Mil­lenium MPS-750X E-Drum Mesh Set Assembly Instructions

Add to my manuals
20 Pages

advertisement

Mil­lenium MPS-750X E-Drum Mesh Set Assembly Instructions | Manualzz

MPS-750X

e-drum set assembly instructions

Musikhaus Thomann

Thomann GmbH

Hans-Thomann-Straße 1

96138 Burgebrach

Germany

Telephone: +49 (0) 9546 9223-0

E-mail: [email protected]

Internet: www.thomann.de

27.05.2020, ID: 454015

Table of contents

Table of contents

1

Safety instructions.......................................................................................................................................................................................................... 4

2

Scope of delivery.............................................................................................................................................................................................................. 5

3

Assembly.............................................................................................................................................................................................................................. 7

4

Protecting the environment.................................................................................................................................................................................... 18

MPS-750X

3

Safety instructions

1 Safety instructions

DANGER!

Danger for children

Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children.

Choking hazard!

Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke!

Never let children unattended use electrical devices.

NOTICE!

Possible staining

The plasticiser contained in the rubber feet of this product may possibly react with the coating of your parquet, linoleum, laminate or PVC floor and after some time cause permanent dark stains.

In case of doubt, do not put the rubber feet directly on the floor, but use felt-pad floor protectors or a carpet.

4 e-drum set

Scope of delivery

2 Scope of delivery

Before you assemble your drum set, make sure the contents of package is complete according to the following list and figure.

20

21

22

23

16

17

18

19

24

25

1

1

1

1

1

1

1

1

1

1

12

13

14

15

8

9

10

11

6

7

4

5

2

3

Item Qty.

1 2 Lateral support tube left and right

2

1

Support tube for left and right crossbeams

Lower horizontal connection tube

1

2

1

2

Crossbeam for the Snare

Crossbeams left and right

Upper horizontal connection tube

Cymbal bracket (Crash and Ride)

2

4

1

3

1

1

1

3

Connection for the cymbal holder (Crash and Ride)

Sleeve for mounting bracket / mounting rod for the pads

Mounting bracket for the pads

Mounting rod for the pads

Hi-hat pad (10 inch)

Crash (12", two zones, with stop function)

Ride (14", three zones, with stop function)

Tom pad (10", two zones, mesh head)

Snare pad (10", two zones, mesh head)

Bass drum pad (8" mesh head)

Bass drum pad pedal

Hi-hat tripod with pedal

Hi-hat bracket e-drum module Millenium MPS-750X

Multiple cable for connecting the pads, cymbals and pedals to the e-drum module

Drum key

Set of drum sticks

User manual e-drum module

MPS-750X

5

Scope of delivery

Item Qty.

26 1 Assembly instructions e-drum set

27 1 Plug-in power supply

6 e-drum set

Assembly

3 Assembly

Overview

Loosen the screws of the clamps before sticking the tubes together. Mount the various elements in the specified sequence. The final positions of the components are shown in the illustration below.

16

17

18

19

12

13

14

15

Hi-hat pad (10 inch)

Crash (12", two zones, with stop function)

Ride (14", three zones, with stop function)

Tom pad (10", two zones, mesh head)

Snare pad (10", two zones, mesh head)

Bass drum pad (8" mesh head)

Bass drum pad pedal

Hi-hat tripod with pedal

MPS-750X

7

Assembly

Assembling the rack

CAUTION!

Danger of cuts on hands and fingers

When connecting the parts, take care for sharp edges on the metal tubes, screws etc.

1.

Attach the clamp (4a) of the snare crossbeam (4) to one of the two lateral support tubes (1).

2.

Then tighten the wing nut of the clamp (4a).

8 e-drum set

Assembly

1.

Fasten the two lateral support tubes (1) in the fastening clamps of the horizontal connecting tube (3).

2.

Then tighten the wing nuts of the fastening clamps.

1.

Attach the crossbeam for the snare (4) to the left support tube (1).

2.

Then tighten the wing nut of the fastening clamps.

MPS-750X

9

Assembly

1.

Attach the two crossbeams (5) to the two lateral support tubes (1).

2.

Then tighten the wing nuts of the fastening clamps.

1.

Fasten the two support tubes for the crossbeams (2) in the fastening clamps of the crossbeams (5).

2.

Then tighten the wing nuts of the fastening clamps.

e-drum set

10

1.

Fasten the two lateral support tubes (1) in the fastening clamps of the horizontal connecting tube (6).

2.

Then tighten the wing nuts of the fastening clamps.

Assembly

MPS-750X

11

Assembly

1.

Attach the two connections for the cymbal holder (8) and the cymbal holder (7) to the two lateral support tubes (1).

2.

Then tighten the wing nuts of the fastening clamps.

e-drum set

12

Assembly

1.

Attach the sleeve for the mounting bracket (9) and the mounting bracket (10) in the bracket for the snare on the crossbeam

(4).

2.

Then attach the sleeves for the mounting rods (9) and the mounting rods (11) in the holders for the tom pads on the right crossbeam (5) and on the horizontal connecting tube (6).

3.

Then tighten the wing nuts of the brackets.

MPS-750X

13

Assembly

Mounting tom pads on the rack

1.

Attach the tom pads (15) to the mounting rods (9) and tighten the wing nuts of the tom pads hand-tight.

2.

Align the pads on the rack to meet your needs, then tighten the wing nuts of the brackets and the wing nuts of the tom pads evenly.

Mounting cymbals on the rack

1.

Unscrew the wing nuts from the cymbal holders (7) and take the felt washers off the holders.

2.

Place the cymbals (13, 14) as shown in the figure on the holders. Be sure to attach the crash pad (12") to the left holder and the ride pad (14") to the right cymbal holder.

3.

Place the felt washers on the cymbals (13, 14) and fix the cymbals with the associated wing nuts on the holders.

e-drum set

14

Assembly

Mounting the Hi-hat on the rack

1.

Screw on the wing nuts of the hi-hat tripod with pedal (19) and open the feet. Then tighten the wing nuts of the brackets.

2.

Insert the hi-hat holder (20) into the hi-hat tripod with pedal (19) and tighten the holder clockwise.

3.

Unscrew the wing nuts from the Hi-hat holder (20) and take the felt washers off the holders.

4.

Place the Hi-hat (12) as shown in the figure on the holder.

5.

Place the felt washers on the cymbals and fix the Hi-hat (12) with the associated wing nut on the holder.

MPS-750X

15

Assembly

Setting up the bass drum pedal

1.

Screw the bass drum pad and the associated foot (17) with the supplied screws using the drum key (23).

2.

Engage the bolt of the foot machine (18) into the provided recess on the bass drum pad (17).

Mounting the drum module on the rack

1.

Put the drum module (21) up to the stop into the free bracket of the left crossbeam (5). Insert the D-sub plug of the multiple cable (22) into the provided socket on the bottom side of the drum module.

2.

Tighten the D-sub plug with the hand screws.

3.

Align the module and tighten the wing nut of the bracket.

Bass Drum positioning

Place the pedal with the bass drum pad centred under the rack. Position the bass drum pedal centred in front of the pad.

e-drum set

16

Assembly

Set-up and cabling

Set up the rack, the pads and the cymbals according to your needs. Finally, position the pedal with the bass drum pad in front of the rack and connect all trigger cables to the e-drum module.

The skin tension of the mesh heads is relatively low in the delivery state in order to avoid damage during transport. For good playa‐ bility and better trigger behaviour, adjust the skin tension to your playing habits.

MPS-750X

17

Protecting the environment

4 Protecting the environment

Disposal of the packaging material

For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling.

Ensure that plastic bags, packaging, etc. are properly disposed of.

Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling.

Please follow the notes and markings on the packaging.

Disposal of your old device

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version.

Do not dispose with your normal household waste.

Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.

18 e-drum set

Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Questions and Answers

What safety precautions should be taken when using the Millenium MPS-750X E-Drum Mesh Set?
Ensure that plastic bags and packaging are disposed of properly and kept away from children, and that children are supervised when using the device due to the risk of choking on small parts.
What is the purpose of the rubber feet on the product, and what precautions should be taken regarding floor surfaces?
The rubber feet contain plasticizers that may react with certain floor coatings, causing permanent stains. It is recommended to use felt-pad floor protectors or a carpet to prevent this.
What are the main components of the Millenium MPS-750X E-Drum Mesh Set?
The main components include lateral support tubes, support tubes for crossbeams, horizontal connection tubes, crossbeams, cymbal brackets, connections for cymbal holders, sleeves for mounting brackets, mounting rods, pads, pedals, tripod, drum module, multiple cable, drum key, and drum sticks.
How do I mount the tom pads on the rack?
Attach the tom pads to the mounting rods and hand-tighten the wing nuts. Adjust the pads' position and then tighten the brackets' and tom pads' wing nuts evenly.
How do I mount the cymbals on the rack?
Remove the wing nuts from the cymbal holders, place the cymbals on the holders as indicated in the manual, add the felt washers, and secure the cymbals with the wing nuts.

Related manuals

Download PDF

advertisement