Spark Modern Fires 54 3ft Fire Ribbon Vent Free Vu Thru Installation Manual

Add to My manuals
28 Pages

advertisement

Spark Modern Fires 54 3ft Fire Ribbon Vent Free Vu Thru Installation Manual | Manualzz

FIRE RIBBON

Unvented (Vent-Free) Gas Fireplace

Owner’s Operation and Installation Manual

MODEL 54

FR-N, FR-P

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

— Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

— Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilating air must be provided.

Refer to page 4,

Air for Combustion and

Ventilation.

Report # 0321GF00

8S

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency, or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

This fireplace has been tested and approved by OMNI-Test

Heaters.

Laboratories, Inc. under ANSI

Z21.11.2 20

19

Unvented Gas-Fired Room

This appliance may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

2

TABLE OF CONTENTS

Safety Information ........................................................ 2

Local Codes .................................................................. 3

Locating Firebox ........................................................... 4

Product Dimensions ...................................................... 4

Air For Combustion and Ventilation ............................ 4

Installation ..................................................................... 7

Built-In Fireplace Installation ....................................... 8

Operating Fireplace ..................................................... 11

Inspecting Burners ...................................................... 15

Cleaning and Maintenance .......................................... 16

Troubleshooting .......................................................... 17

Wiring Diagram .......................................................... 21

Specifications .............................................................. 21

Parts List and Illustrated Parts Breakdown ................. 22

Warranty Information .................................. Back Cover

SAFETY INFORMATION

IMPORTANT: A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer's barrier for this appliance.

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this fireplace.

Improper use of this fireplace can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.

DANGER: Carbon monoxide poisoning may lead to death!

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

Carbon Monoxide Poisoning:

Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness, or nausea. If you have these signs, the fireplace may not be working properly.

Get fresh air at once!

Have fireplace serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol, and those at high altitudes.

Propane/LP Gas:

Propane/LP gas is odorless. An odormaking agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade.

Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to safe and proper operation of this fireplace.

WARNING: Any change to this heater or its controls can be dangerous.

WARNING: Do not use a blower insert, heat exchanger insert, or other accessory not approved for use with this fireplace.

WARNING: Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns. Ceiling fans can create drafts that alter burner flame patterns. Altered burner patterns can cause sooting.

Do not place clothing or other flammable material on or near the appliance. Never place any objects on the heater.

Fireplace front and sides become very hot when running fireplace. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.

Carefully supervise young children when they are in the room with fireplace. When using the hand-held remote accessory, keep selector switch in the OFF position to prevent children from turning on burners with remote.

Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.

1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

2. Do not place propane/LP supply tank(s) inside any structure. Locate propane/LP supply tank(s) outdoors

(propane/LP units only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in your building

• immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions

• if you cannot reach your gas supplier, call the fire department

4. This fireplace shall not be installed in a bedroom or bathroom.

5. Do not use this fireplace as a wood-burning fireplace.

6. To prevent the creation of soot, follow the instructions in

Cleaning and Maintenance

section.

Keep the appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

7. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

8. This fireplace needs fresh air ventilation to run properly. This fireplace has an Oxygen Depletion Sensing

(ODS) safety shutoff system. The ODS shuts down the fireplace if not enough fresh air is available. See

Air for Combustion and Ventilation

, pages 4 through

6. If fireplace keeps shutting off, see

Troubleshooting,

pages 17 through 20.

9. Do not run fireplace

• where flammable liquids or vapors are used or stored

• under dusty conditions

10. Do not use this fireplace to cook food or burn paper or other objects.

11. Do not use fireplace if any part has been exposed to or under water. Immediately call a qualified service technician to inspect the fireplace and to replace any part of the control system and any gas control which has been under water.

12. Turn fireplace off and let cool before servicing. Only a qualified service person should service and repair fireplace.

13. Operating fireplace above elevations of 4,500 feet could cause pilot outage.

14. To prevent performance problems, do not use propane/

LP fuel tanks of less than 100 lbs. capacity.

15. Provide adequate clearances around air openings.

LOCAL COdES

Install and use fireplace with care. Follow all local codes.

In the absence of local codes, use the latest edition of The

National Fuel Gas Code ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

State of Massachusetts:

Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for bedroom and bathroom installation in the Commonwealth of

Massachusetts.

The installation must be made by a licensed plumber or gas fitter in the

Commonwealth of Massachusetts.

3

4

LOCATINg FIREBOx

PLANNING

Carefully plan where you will install the firebox. This will save time and money later during the installation process.

Before installing, consider the following:

1. Determine the best firebox location. Allow for wall and ceiling clearances (see

Built-In Fireplace Installation,

page 8).

2. Allow for location of control switch in wall adjacent to fireplace. There is 9 linear feet of provided wire.

3. Gather everything needed to complete the installation.

4. Make sure installation location will provide proper air for combustion and ventilation.

PROduCT dIMENSIONS

5.

25 ”

5”

28.25”

11”

11”

TOP VIEW

FRONT VIEW

41.16”

36”

36”

RIGHT SIDE VIEW

31.25”

2”

18”

18”

28.25”

18”

18”

AIR FOR COMBuSTION

ANd VENTILATION

WARNING: This heater shall not be installed in a room or space unless the required volume of indoor combustion air is provided by the method described in the

National Fuel Gas Code, ANSI Z223.1/

NFPA 54,

the

International Fuel Gas Code,

or applicable local codes.

Read the following instructions to insure proper fresh air for this and other fuelburning appliances in your home.

Today’s homes are built more energy efficient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.

ELECTRICAL

There is a provided “J” box, accessible from either end of the fireplace. Electrical connection should be made by a qualified installer. Follow all local codes.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from

National Fuel Gas Code

ANSI Z223.1/NFPA 54,

Section 5.3,

Air for Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will help you classify your space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

Unusually tight construction is defined as construction where: a. walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder with a rating of one perm (6 x 10 per pa-sec-m

2 or sealed

and

-11 kg

) or less with openings gasketed b. weather stripping has been added on openable windows and doors

and

c. caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wallceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air. See

Ventilation Air From Outdoors

, page 5

.

If your home does not meet all of the three criteria above, proceed to

Determining Fresh-Air Flow for

Fireplace Location

, page 6.

Confined and Unconfined Space

The National Fuel Gas Code ANSI Z223.1/NFPA 54 defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m

3

per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m

3

per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconfined space.

* Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconfined space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor on the wall connecting the two spaces (see Figure 1). You can also remove door into adjoining room (see Figure 1). Follow the

National Fuel Gas Code ANSI Z223.1/NFPA 54,

Section 5.3,

Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

Ventilation

Grills

Into Adjoining

Room,

Option 1

Or

Remove

Door into

Adjoining

Room,

Option

3

Figure 1 - Ventilation Air from Inside Building

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts.

You must provide two permanent openings: one within

12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces.

Follow the

National Fuel Gas Code ANSI Z223.1/NFPA

54,

Section 5.3,

Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

IMPORTANT:

Do not provide openings for inlet or outlet air into attic if attic has a thermostat-controlled power vent.

Heated air entering the attic will activate the power vent.

Outlet

Air

12"

12"

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilated

Attic

Outlet

Air

To Attic

To

Crawl

Space

Inlet

Air

Inlet Air

Ventilated

Crawl Space

Figure 2 - Ventilation Air from Outdoors

5

AIR FOR COMBuSTION

ANd VENTILATION

Continued

DETERMINING FRESH-AIR FLOW

FOR FIREPLACE LOCATION

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space.

Space:

Includes the room in which you will install fireplace plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = cu. ft. (volume of space)

Example:

Space size 22 ft. (length) x 18 ft. (width) x

8 ft. (ceiling height) = 3168 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

_______ (volume of space) x 20 = (Maximum Btu/Hr the space can support)

Example:

3168 cu. ft. (volume of space) x 20 = 63,360

(maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free fireplace _____________ Btu/Hr

Gas water heater* ______________ Btu/Hr

Gas furnace ___________________ Btu/Hr

Vented gas heater ______________ Btu/Hr

Gas fireplace logs ______________ Btu/Hr

Other gas appliances*

+

________ Btu/Hr

Total

=

________ Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

Example:

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

____ Btu/Hr (max. the space can support)

____ Btu/Hr (actual amt. of Btu/Hr used)

Example: 63,300 Btu/Hr (maximum the space can support)

73,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A. Rework work sheet, adding the space of an adjoining room.

If the extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See

Ventilation Air from Inside Building,

page 5.

B. Vent room directly to the outdoors. See

Ventilation Air from Outdoors,

page 5.

C. Install a lower Btu/Hr fireplace, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space.

You will need no additional fresh air ventilation.

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the

National Fuel Gas Code, ANSI Z223.1/

NFPA 54,

Air for Combustion and Ventilation, or applicable local codes.

Total

=

________ Btu/Hr

6

INSTALLATION

NOTICE: This appliance is intended for supplemental heating. Use this heater along with your primary heating system.

Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualified service person must install fireplace. Follow all local codes.

WARNING: Never install the fireplace

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture, clothing, or other flammable objects are less than

42 inches from the front, top, or sides of the fireplace

• in high traffic areas

• in windy or drafty areas

CAUTION: This fireplace creates warm air currents. These currents move heat to wall surfaces next to fireplace. Installing fireplace next to vinyl or cloth wall coverings or operating fireplace where impurities

(such as tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls.

Note:

Your fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface on the rear, sides, or top of your fireplace, except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be placed directly against wall or framing materials.

Use the dimensions shown for rough openings to create the easiest installation (see

Built-In Fireplace Installation

, page 8).

IMPORTANT:

Vent-free heaters add moisture to the air.

Although this is beneficial, installing fireplace in rooms without enough ventilation air may cause mildew to form from too much moisture. See

Air for Combustion and

Ventilation,

page 4.

IMPORTANT:

Make sure the fireplace is level. If fireplace is not level, fireplace will not work properly.

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP) for your fireplace. If your gas supply is not correct, do not install fireplace. Call dealer where you bought fireplace for proper type fireplace.

WARNING: This appliance is equipped for either natural or propane (LP) gas. Field conversion is not permitted.

INSTALLATION CLEARANCES

WARNING: Maintain the minimum clearances. If you can, provide greater clearances from floor, ceiling, and adjoining wall.

Carefully follow the instructions below. This will ensure safe installation.

Minimum Wall and Ceiling Clearances

A. Clearances from the side of the fireplace opening to any combustible material and wall should follow diagram in

Figure 3.

Example:

The face of a mantel, bookshelf, etc. is made of combustible material and protrudes

3.5" from the wall. This combustible material must be 4" from the side of the fireplace cabinet (see Figure 3).

B. Clearances from the top of the fireplace opening to the ceiling should not be less than 42 inches.

C. When the firebox is installed on carpeting or other combustible material, other than wood flooring, the firebox should be installed on a metal or wood panel extending the full width and depth of the enclosure.

D. Clearances from the bottom of firebox to the floor is 0 inches.

CAUTION: Do not install the firebox directly on carpet or vinyl.

Example

*Minimum 16 inches from Side Wall

Figure 3 - Minimum Clearance for Combustible to Wall

7

8

INSTALLATION

Continued

NOTICE: If installing on combustible flooring other than wood (carpet, vinyl flooring, vinyl tile, etc.), a metal or wood panel extending the full length and depth of the unit must be installed under the fireplace.

NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.

VENT FREE FIRE

RIBBON FRAMING

DIMENSIONS

VENT FREE FIRE RIBBON

FACING DIMENSIONS

MINIMUM NON-COMBUSTIBLE

MATERIALS

Remote

Switch

Remote

Switch

31.5”

COMBUSTIBLE

MATERIAL

NON-COMBUSTIBLE

MATERIAL AREA

2 8.2

5 ”

0.50”

42”

Figure 4 - Installation Specifications

42”

INSTALLING GAS PIPING TO

FIREPLACE LOCATION

WARNING: This appliance requires a

1/2" NPT (National Pipe Thread) inlet connection to the pressure regulator.

WARNING: A qualified service person must connect fireplace to gas supply. Follow all local codes.

CAUTION: Never connect propane/LP fireplace directly to the propane/LP supply.

This fireplace requires an external regulator

(not supplied). Install the external regulator between the fireplace and propane/LP supply.

WARNING: Never connect natural gas fireplace to private (non-utility) gas wells.

This gas is commonly known as wellhead gas.

Installation Items Needed

Before installing fireplace, make sure you have the items listed below.

• external regulator for propane/LP unit only (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• test gauge connection *

• sediment trap (optional)

• tee joint

• pipe wrench

• approved flexible gas line with gas connector (if allowed by local codes) (not provided)

* A CSA/AGA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA/AGA design-certified equipment shutoff valve from your dealer.

For propane/LP units, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 13 inches of water. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 5. Pointing the vent down protects it from freezing rain or sleet.

External

Regulator

Vent

Pointing

Down

Propane/LP

Supply Tank

Figure 5 - External Regulator with Vent Pointing Down

CAUTION: Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to fireplace. If pipe is too small, undue loss of pressure will occur.

Installation must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from fireplace.

NEW CONSTRUCTION

Remove the remote receiver from the heat shield inside the fireplace access area. Route the wire extension cable out the side of the fireplace to the best location for access to the switch. There is a total of 9 feet (3 meters) of wire.

Mount the switch into an electrical box in an adjacent wall.

Be careful not to damage the wires.

EXISTING CONSTRUCTION

As an option, the remote receiver may be retained inside the fireplace bottom. Battery access is better when located in an adjacent wall.

SHUTOFF VALVE

IMPORTANT: Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.

Check your building codes for any special requirements for locating equipment shutoff valve to fireplaces.

Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged fireplace valves.

Never use sealant on flare threads.

CSA/AGA Design-

Certified Equipment

Shutoff Valve With

1/8" NPT Tap*

Approved

Flexible

Gas Line

3" Minimum

Tee

Joint

Pipe

Nipple

Cap

Sediment

Trap

Figure 6 - Gas Connection

CAUTION: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.

We recommend that you install a sediment trap in supply line as shown in Figure 6. Locate sediment trap where it is within reach for cleaning. Install in piping system between fuel supply and fireplace. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into fireplace gas controls. If sediment trap is not installed or is installed wrong, fireplace may not run properly.

CONNECTING FIREPLACE TO GAS

SUPPLY

1. Remove access panel.

2. Route gas line (provided by installer) from equipment shutoff valve to fireplace. Route flexible gas supply line through one of the access holes.

3. Attach the flexible gas line to gas supply as per Figure

7. Check tightness of flexible gas line attached to gas regulator of fireplace and check all gas connections for leaks (see

Checking Gas Connections,

page 10).

NOTICE: Most building codes do not permit concealed gas connections. A flexible gas line is provided to allow accessibility from the fireplace (see Figure 7). The flexible gas supply line connection to the equipment shutoff valve should be accessible.

To Fireplace

Gas Regulator

Flexible Gas

Line from

Equipment

Shutoff Valve

Equipment

Shutoff Valve

To External

Regulator

Figure 7 - Attaching Flexible Gas Lines Together

* Purchase the optional CSA/AGA design-certified equipment shutoff valve from your dealer.

** Minimum inlet pressure for purpose of input adjustment.

9

INSTALLATION

Continued

CHECKING GAS CONNECTIONS

Note: If fireplace is fully assembled, you must first remove the floor tray and heat shield before checking gas connections. Refer to the illustrated parts list in this manual for the floor tray and heat shield locations. Replace floor tray and heat shield after checking gas connections.

Test Pressures Equal To or Less Than 1/2

PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 8).

2. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter of natural gas or using compressed air.

3. Check all joints from gas meter to equipment shutoff valve for natural gas or propane/LP supply to equipment shutoff valve for propane/LP. Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

4. Correct all leaks at once.

WARNING: Test all gas piping and connections, internal and external to unit, for leaks after installing or servicing. Correct all leaks at once.

POSITION

WARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once.

Equipment

Shutoff

Valve

CAUTION: Make sure external regulator has been installed between propane/

LP supply and fireplace. See guidelines under

Connecting Fireplace to Gas Supply,

page 9.

Pressure Testing Gas Supply Piping

System

Test Pressures In Excess Of 1/2 PSI

(3.5 kPa)

1. Disconnect fireplace with its main gas valve (control valve) and equipment shutoff valve from gas supply pipping system. Pressures in excess of 1/2 psi will damage fireplace gas regulator.

2. Cap off open end of gas pipe where equipment shutoff valve was connected.

3. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter of natural gas or using compressed air.

4. Check all joints of gas supply piping system. Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Reconnect fireplace and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.

OFF

Closed

Figure 8 - Equipment Shutoff Valve

MANUAL SHUT-OFF VALVE GRH/OV 020

PRESSURE TESTING FIREPLACE

GAS CONNECTIONS

1. Open equipment shutoff valve (see Figure 8).

2. Open main gas valve located on or near gas meter for natural gas or open propane/LP supply tank valve.

3. Make sure control knob of fireplace is in the OFF position.

4. Check all joints from equipment shutoff valve to gas control valve. Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light fireplace (see

Operating Fireplace,

page 11).

Check all other internal joints for leaks.

7. Turn off fireplace (see

Turning Off The Appliance,

page

11).

10

OPERATINg FIREPLACE

FOR YOUR SAFETY

READ BEFORE

LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A. This appliance is equipped with an ignition device which automatically lights the pilot. Do Not try to light the pilot by hand.

B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not

use any phone in your building.

• Immediately call your gas supplier from a neigh bor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

C. Main gas valve in this appliance is not serviceable and does not have any control knobs or switches to operate. Do not remove heat shields covering the valve and electronic devices; do not try to repair or modify the valve as it may result in a fire or explo sion. Call a qualified service technician if you have any safety concerns.

D. Do not use this appliance if any part has been under water. Immediately call a qualified service techni cian to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

OPERATING

INSTRUCTIONS

1. STOP! Read the safety information, starting on page 2.

2. Remove floor tray from the appliance (see illustrated parts list).

3. Turn off all electric power to the appliance. Unplug

DC adapter from the power outlet.

4. Do not attempt to light the pilot by hand.

5. Lift and remove heat shield covering electronic components inside of the unit (see illustrated parts list).

6. Turn main shutoff valve counterclockwise to the ON position.

7. Set remote receiver switch to OFF position.

ON REMOTE OFF

PRG

Figure 9a - Remote Receiver Switch in OFF Position

8. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information.

If you don’t smell gas, go to the next step.

Note:

Before applying any power supply to the DFC board, please verify that the electrical connections are in accordance to Figure 24, page 21.

9. Plug supplied DC adapter into 110V power outlet.

10. Connect the wire to the DC input plug at the unit.

11. Replace heat shield.

12. Locate remote receiver either inside the unit (see illustrated parts list), or mounted in adjacent wall.

Make sure that the remote receiver switch is in

“REMOTE” (middle) position.

ON REMOTE OFF

ON REMOTE OFF

PRG

Figure 9b - Remote Receiver Switch in REMOTE

Position

13. Replace floor tray.

14. If the appliance will not operate, follow the instruc tions “To Turn Off Gas To Appliance” and call your service technician or gas supplier.

Initializing the System for the First Time

1. Set the remote receiver switch to the OFF position.

PRG

Figure 9c - Remote Receiver Switch in OFF Position

2. If installed, set the pilot flame mode selector switch to the IPI position.

3. Install 4 AA batteries into the battery holder and verify the polarity indicated on the battery holder.

Connect the battery holder to the DFC’s main wiring harness.

11

4. Connect the AC/DC wall adapter to the DFC’s DCjack connector on the main wiring harness and plug it into the main power supply.

Setting the Appliance into Continuous Pilot

Ignition Mode

1. Set the IPI/CPI pilot mode switch to the CPI posi tion (switch closed). At that point the unit will im mediately ignite the pilot flame. The pilot flame will remain ON.

Note:

If pilot does not stay lit, contact a qualified service person or gas supplier for repairs.

ON REMOTE OFF

PRG

2. If necessary, remove access panel from the appliance to access manual shutoff valve on gas line.

3. Turn the gas control manual valve clockwise to the full OFF position.

4. If necessary, replace access panel.

Command Definitions

Pilot

IPI/CPI

Switch

Opened, IPI

Opened, IPI

Closed, CPI

Closed, CPI

Main

Turn-On

Switch

Opened

Closed

Opened

Closed

Command

Name

Turn-OFF

Turn-ON

Pilot-ON

Turn-ON

Fireplace

State

Flames OFF

Pilot & Main

Burner Flames

ON

Pilot Flame ON

Pilot & Main

Burner Flames

ON

Figure 9d - Remote Receiver Switch in ON Position

Turning ON the Appliance

1. Slide the remote receiver switch to the ON position.

This will allow the main burner to ignite.

Turning OFF the Appliance

1. Slide the remote receiver switch to the OFF position.

This will turn off the main burner.

Note:

If the Continuous Pilot ignition mode is selected, the pilot flame will remain ON. To turn the pilot flame completely OFF, switch the appliance into Intermittent

Pilot ignition mode and set the IPI/CPI pilot mode switch to the IPI position (switch opened).

Note:

You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

WARNING: Make sure the remote receiver switch is in the OFF position when you are away from home for long periods of time. Heater may come on automatically with remote receiver switch in the “REMOTE” position.

TO TURN OFF GAS

TO APPLIANCE

1. Turn off all electric power to the appliance if service is to be performed. Unplug DC adapter from the power outlet.

REMOTE CONTROL

OPERATION

Proflame G-Fire System Operation

Initializing the System for the First Time

1. Install the 4 AA batteries into the receiver batter bay.

Note the polarity of the batteries and insert into the battery bay as indicated on the battery cover (+/-).

2. Place the 3-position slider switch in the REMOTE position.

3. Insert the end of a paper clip into the hole marked

PRG on the receiver front cover. The receiver will beep three times to indicate that it is ready to synchronize with a transmitter.

4. Install the 3 AAA batteries in the transmitter battery bay located on the base of the transmitter.

5. Press the ON button on the transmitter. The receiver will beep four times to indicate the transmitter’s command is accepted. The system is now initialized.

Temperature Indication Display

1. With the system in the OFF position, press the

THERMOSTAT key and the MODE key at the same time.

2. Look at the LCD screen on the transmitter to verify that a °C or °F is visible to the right of the room temperature display (see Figure 10).

12

2. Press the up-arrow key to increase the flame height.

Note:

If you press the up-arrow while the remote system is ON but the flame is OFF, the flame will come on in the high position. A single “beep” from the receiver will confirm the command.

Figure 10 - Remote Control Display in Farenxheit and

Celsius

Turning ON the Appliance

1. Press the ON/OFF button on the transmitter. The transmitter screen will display all active icons. The receiver will command the DFC board to start the ignition process. Once the pilot flame is lit, the DFC board will open the main valve outlet and the main burner will ignite. A single “beep” from the receiver will confirm the command.

Turning OFF the Appliance

1. Press the ON/OFF button on the transmitter. The transmitter LDC display will only show the room temperature and icon (see Figure 11). The receiver disconnects and will command the DFC board to turn off the burner. Depending upon the system model (IPI or CPI), the pilot may shut off (IPI model) or remain lit (CPI model) and the main burner turns off. A single “beep” from the receiver will confirm the command.

Flame OFF Flame Level 1

Flame Level 5 Flame Level Max.

Figure 12 - Remote Control Displaying Flame Levels

Figure 11 - Remote Control Displaying Room

Temperature

Flame Height Control

Proflame GT

1. With the system ON and the flame present in the appliance, press the down-arrow key to turn flame

OFF.

2. Press the up-arrow key and the flame will turn

ON.

Proflame GTM & GTMF

These units have six flame levels (see Figure 12).

1. With the system ON and the flame level at maximum height, press the down-arrow key once to reduce the flame height by one step. Continue pressing downarrow key until flame is turned OFF.

Figure 13 - Remote Control Displaying Split Flow Mode

Room Thermostat

(Transmitter Operation)

The remote control can operate as a room thermostat.

The thermostat can be set to a desired temperature to control the comfort level in the room.

1. To activate this function, press the Thermostat key.

The LCD display on the transmitter will change to show that the room thermostat is ON and the set temperature is now displayed (see Figure 14).

2. Adjust the set temperature by pressing the up or down-arrow keys until the desired set temperature is displayed on the LCD screen (see Figure 14).

Room

Temperature

Set

Temperature

Figure 14 - Remote Control Displaying Room

Temperature and Set Temperature

13

Smart Thermostat

(Transmitter Operation- Proflame GTM, GTMF, &

GTMFS only)

The Smart Thermostat function adjusts the flame height in accordance to the difference between the set point temperature and the actual room temperature. As the room temperature gets closer to the set point, the Smart

Function will modulate the flame down.

1. To activate this function, press the Thermostat key until the word “SMART” appears to the right of the temperature bulb on the LCD screen (see Figure

15).

2. To adjust the set temperature, press the up or down-arrow keys until the desired set temperature is displayed on the LCD screen.

Low Battery Power Detection

Receiver

The life span of the receiver batteries depends upon various factors: battery quality, number of appliance ig nitions, number of thermostat set point changes, etc.

When the receiver batteries are low, no “beep” will sound from the receiver when a transmitter command is sent. Replace batteries when this happens.

Transmitter

The life span of the transmitter batteries depends upon various factors: battery quality, number of appliance ig nitions, number of thermostat set point changes, etc.

When the transmitter batteries are low, an icon will appear on the LCD display (see Figure 17). Replace batteries when this icon appears.

Figure 15 - Remote Control Displaying Smart

Thermostat Function

Key Lock

This function will lock the keys to avoid unsupervised operation.

1. To activate this function, press the MODE and UP keys at the same time. A lock icon will appear on the

LCD screen (see Figure 16).

2. To deactivate this function, press the MODE and UP keys at the same time. The lock icon will disappear from the LCD screen.

Figure 17 - Remote Control Displaying Low Battery

Manual Override

If the receiver or transmitter batteries are low or depleted, the appliance can still be turned on manually.

1. Move the receiver’s three-position slider to the ON position. This will bypass the remote control feature of the system and the appliance main burner will turn on.

Figure 16 - Remote Control Displaying Key Lock

Mode

14

Command Definitions

Pilot IPI/CPI

Switch

Receiver Slider

Position

Opened, IPI

Opened, IPI

Closed, CPI

Closed, CPI

“OFF”

“REMOTE”

& “OFF received”

“ON”

“OFF”

“REMOTE”

& “ON received”

“REMOTE”

& “OFF received”

“ON”

“REMOTE”

& “ON received”

Command

Name

Turn-OFF

Turn-ON

Pilot-ON

Turn-ON

Fireplace

State

Flames OFF

Pilot & Main

Burner Flames

ON

Pilot Flame ON

Pilot & Main

Burner Flames

ON

INSPECTINg BuRNERS

Check pilot flame pattern and burner flame patterns often.

PILOT FLAME PATTERN

Figure 18 shows a correct pilot flame pattern. Figure 19 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the flame sensor. This will cause the flame sensor to cool. When the flame sensor cools, the fireplace will shut down.

If pilot flame pattern is incorrect, as shown in Figure 19

• turn fireplace off (see

Turning OFF The Appliance,

page 11)

• see

Cleaning and Maintenance,

page 16

Note:

The correct pilot flame on natural gas units will have a slight curve, but flame should be blue and have no yellow or orange color.

Pilot Burner

MAIN BURNER

Periodically inspect all burner flame holes with the fireplace running. Some burner flame holes may become blocked by debris or rust, with no flame present. If so, turn off fireplace and let cool. Remove blockage. Blocked burner flame holes may create soot.

FRONT BURNER FLAME PATTERN

Figure 20 shows correct front burner flame pattern. Figure 21 shows incorrect front burner flame pattern. The correct burner flame pattern shows yellow tipping at top of blue flame.

If front burner flame pattern is incorrect, as shown in

Figure 21

• turn fireplace off (see

Turning OFF The Appliance,

page 11)

• see

Troubleshooting,

page 17

Flame Sensor

Figure 18 - Correct Pilot Flame Pattern

Pilot Burner

Flame Sensor

Figure 19 - Incorrect Pilot Flame Pattern

Figure 20 - Correct Front Burner Flame Pattern

Showing Blue Flame with Yellow/White Tips

Figure 21 - Incorrect Front Burner Flame Pattern

Showing Solid Yellow/Orange Flame

15

CLEANINg ANd

MAINTENANCE

WARNING: Turn off fireplace and let cool before cleaning.

6. In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure

23). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

CAUTION: Keep burner and control compartment clean. See installation and operating instructions accompanying heater. Inspect these areas of fireplace before each use. Have fireplace inspected yearly by a qualified service person. Fireplace may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.

WARNING: Failure to keep the primary air opening of the burner clean may result in sooting and property damage.

Figure 22 - Injector Holder On Outlet Burner Tube

BURNER INjECTOR HOLDER AND

PILOT AIR INLET HOLE

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning flame.

Keep these holes clear of dust, dirt, lint, and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualified service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than

30 PSI. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don't follow directions on the can, you could damage the pilot assembly.

1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2. Inspect burner, pilot, and primary air inlet holes on injector holder for dust and dirt (see Figure 22).

3. Blow air through the ports and holes in the burner.

4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.

5. Blow air into the primary air holes on the injector holder.

Burner

Tube

Pilot

Assembly

Figure 23 - Pilot Inlet Air Hole

Ports/Slots

Pilot Air

Inlet Hole

Replace any screen or guard (heat shield or cover), before operating appliance.

16

TROUBLESHOOTING

Help is available by emailing to

[email protected]

or calling 866-938-3846.

WARNING: Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater.

CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/pilot unit.

Note:

All troubleshooting items are listed in order of operation.

OBSERVED PROBLEM

When remote button is pressed, there is no spark at ODS/pilot

When remote button is pressed, there is spark at ODS/pilot but no ignition

Pilot light stays on when main burner is turned OFF

POSSIBLE CAUSE

1. Ignitor electrode not connected to ignitor cable

2. Ignitor cable pinched or wet

3. Broken ignitor cable

4. Bad ignitor

5. Ignitor electrode broken

6. Ignitor electrode positioned wrong

1. Gas supply turned off or equipment shutoff valve closed

2. Air in gas lines when installed

3. Depleted gas supply

4. ODS/pilot is clogged

5. Gas regulator setting is not correct

1. Switch in wiring harness set to wrong position

2. IPI/CPI switch in wrong position

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if pinched by any metal or tubing.

Keep ignitor cable dry

3. Replace ignitor cable

4. Call for service

5. Replace pilot assembly

6. Replace pilot assembly

1. Turn on gas supply or open equipment shutoff valve

2. Continue holding down control knob. Repeat igniting operation until air is removed

3. Contact local propane/LP gas company

4. Clean ODS/pilot (see

Cleaning and Maintenance,

page 16) or replace ODS/ pilot assembly

5. Replace gas control

1. Change switch position

2. Check toggle switch in wiring harness marked CPI/IPI.

Make sure switch is in IPI position

17

18

OBSERVED PROBLEM

ODS/pilot lights but flame goes out

Burner does not light after

ODS/pilot is lit

Delayed ignition burner

TROUBLESHOOTING

continued

POSSIBLE CAUSE

1. Equipment shutoff valve not fully open

2. Pilot flame not touching flame sensor, which allows flame sensor to cool, causing pilot flame to go out. This problem could be caused by one or both of the following:

A) Low gas pressure

B) Dirty or partially clogged

ODS/pilot

3. Flame sensor connection loose at control valve

4. Flame sensor damaged

5. Control valve damaged

6. Safety interlock system has been triggered

REMEDY

1. Fully open equipment shut off valve

2. A) Contact local propane/LP gas company

B) Clean ODS/pilot (see

Cleaning and Maintenance,

page 16) or replace ODS/ pilot assembly

3. Hand tighten until snug, then tighten 1/4 turn more

4. Replace pilot assembly

5. Replace control valve

6. Wait one minute for safety interlock system to reset.

Repeat ignition operation.

1. Inlet gas pressure is too low

2. Burner orifice clogged

3. Thermopile leads disconnected or improperly connected

4. Burners will not come on in remote position

5. Wire disconnected from gas control

1. Contact local natural or propane/LP gas company

2. Clean burner (see

Cleaning and Maintenance,

page 16) or replace burner orifice

3. Reconnect leads (see

Wiring

Diagram,

page 21)

4. Replace battery in transmitter and receiver

5. Reconnect wire (see

Wiring

Diagram,

page 21)

1. Manifold pressure is too low

2. Burner orifice clogged

1. Contact local natural or propane/LP gas company

2. Clean burner (see

Cleaning and Maintenance,

page 16) or replace burner orifice

OBSERVED PROBLEM

Burner backfiring during combustion

Slight smoke or odor during initial operation

Moisture/condensation noticed on windows

Heater produces a whistling noise when burner is lit

White powder residue forming within burner box or on adjacent walls or furniture

Remote does not function

TROUBLESHOOTING

continued

POSSIBLE CAUSE

1. Burner orifice is clogged or damaged

2. Damaged burner

3. Gas regulator defective

REMEDY

1. Clean burner (see

Cleaning and Maintenance,

page 16) or replace burner orifice

2. Replace damaged burner

3. Replace gas regulator

1. Residues from manufacturing processes

2. Not enough air

3. Gas regulator defective

1. Not enough combustion/ ventilation air

1. Advance control to HI position when burner is cold

2. Air in gas line

3. Air passageways on heater blocked

4. Dirty or partially clogged burner orifice

1. When heated, vapors from furniture polish, wax, carpet cleaners, etc. turn into white powder residue

1. Remote is “locked”

2. Battery is not installed.

Battery power is low

1. Problem will stop after a few hours of operation

2. Check burner for dirt and debris. If found, clean burner (see

Cleaning and

Maintenance,

page 16)

3. Replace gas control

1. Refer to

Air for Combustion and Ventilation

require ments (page 4)

1. Turn control knob to LO position and let warm up for a minute

2. Operate burners until air is removed from line. Have gas line checked by local natural or propane/LP gas company

3. Observe minimum installation clearances (see pages 8)

4. Clean burner (see

Cleaning and Maintenance,

page 16) or replace burner orifice

1. Turn heater off when using furniture polish, wax, cleaners, or similar products

1. See instructions on page 14,

Key Lock

2. Replace batteries in receiver and remote control

19

20

TROUBLESHOOTING

continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT:

Operating fireplace where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.

OBSERVED PROBLEM

Fireplace produces a clicking/ ticking noise just after burners are lit or shut off

POSSIBLE CAUSE

1. Metal expanding while heating or contracting while cooling

REMEDY

1. This is common with most fireplaces. If noise is excessive, contact qualified service person

Fireplace produces unwanted odors

Fireplace shuts off in use

(ODS operates)

Gas odor even when control knob is in OFF position

Gas odor during combustion

1. Fireplace burning vapors from paint, hair spray, glues, cleaners, chemicals, new carpet, etc. (see

IM-

PORTANT

statement above)

2. Low fuel supply (propane/

LP gas only)

3. Gas leak.

See Warning statement at top of page

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

1. Gas leak.

See Warning statement at top of page

2. Control valve or gas control defective

1. Foreign matter between control valve and burner

2. Gas leak.

See Warning statement at top of page

1. Open window and ventilate room. Stop using odor causing products while fireplace is running

2. Refill supply tank (propane/

LP gas only)

3. Locate and correct all leaks

(see

Checking Gas Connections,

page 10)

1. Open window and/or door for ventilation

2. Contact local natural or propane/LP gas company

3. Clean ODS/pilot (see

Cleaning and Maintenance,

page 16)

1. Locate and correct all leaks

(see

Checking Gas Connections,

page 10)

2. Replace control valve or gas control

1. Take apart gas tubing and remove foreign matter

2. Locate and correct all leaks

(see

Checking Gas Connections,

page 10)

WIRINg dIAgRAM

Note:

For proper operation of optional accessories, the wires from the switch to the control must be connected exactly as shown.

Figure 24 - Wiring Diagram

SPECIFICATIONS

Model FR-N

Btu (Variable) ....................................24,000/34,000

Type Gas ..............................................Natural Gas

Ignition ..................................................... Electronic

Pressure Manifold ....................................3.5" W.C.

Inlet Gas Pressure (in. of water)

Maximum .................................................. 10.5"

Minimum* ....................................................... 5"

Shipping Weight ........................................ 120 lbs.

* For input adjustment

Model FR-P

Btu (Variable) ....................................25,000/34,000

Type Gas ..............................................Propane/LP

Ignition ..................................................... Electronic

Pressure Manifold .....................................10” W.C.

Inlet Gas Pressure (in. of water)

Maximum ..................................................... 13”

Minimum* ..................................................... 11”

Shipping Weight ........................................ 120 lbs.

* For input adjustment

21

22

PaRTS LIST

This list contains replaceable parts used in your firebox.

For parts, call 866-938-3846 or email to

[email protected]

KEY

NO.

3

4

5

6

1

2

7

8

9

10

11

12

13

14

15

16

17

18

19

PART NuMBER

FR-N FR-P dESCRIPTION

0.885.001

0.885.002

Proflame valve w/stepper motor

NG - 3.5” to 1.6”

Proflame valve w/stepper motor

LP - 10.0” to 6.4”

0.584.302

84009426000

0.584.302

IPI Ignition board

Vent-free pilot, NG

– 84009608000 Vent-free pilot, LP

30108400020 30108400020 Spark wire (V-F pilot)

30108400021 30108400021 Sensor wire (V-F pilot)

0.584.912 0.584.912 Wire harness and pilot ground wire + CPI/IPI switch

0.584.521

D540000

0.584.521

D540000

Proflame receiver kit

Burner assembly

D540001

D540003

D540004

D540006

D540007

D540008

D540009

D540010

D540002

D540004

D540006

D540007

D540008

D540009

D540010

Burner orifice, NG

Burner orifice, LP

Primary air plate, NG

Wiring heatshield

Valve bracket (pair)

Burner mounting bracket (pair)

3/16” Pilot flex tube

3/8” Flex - Valve to burner

3/8” Inlet flex connector

Items Available - Not Shown

QTY.

1

1

F200066

D540015

0.584.850

0.584.022

0.584.906

D540011

D540012

D540013-XXX D540013-XXX Various tray media - optional

D540014-XXX D540014-XXX Stones - optional (kit)

C100020

F200066

D540015

0.584.850

0.584.022

0.584.906

D540011

D540012

C100020

Shutoff valve

Owners operation & installation manual

Wall AC/DC power adaptor

Proflame GTM transmitter

W-H 750mm (GT/GTM/S) wall adaptor power connector

Firebox floor panel

Media tray - optional

Duplex outlet

1

1

1

1

1

W100074P W100074P Mandatory Safety Screen 2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

ILLUSTRaTED PaRTS BREaKDOWN

23

Mandatory S afety Screen Installation

Part Number: W100074P

1.

Locate and unwrap the safety screen supplied. Look at the fireplace face inner corners and find the notches (slots) in each corner as they will be used to attach the safety screen.

2.

Position the upper end of the screen into the fireplace opening using the notches on two side tabs.

3.

Rotate the bottom of the screen inward and position the center tab into the notch on the fireplace tray. Bottom side tabs should rest inside the firebox opening.

4.

Make sure the safety screen is secured in front of the fireplace.

2

4

INSTALLATION RECORD

The installer should complete the form below that describes the details of the installation. Having this written record of installation information available will greatly expedite trouble-shooting should any problem arise with your fireplace. The installer should keep a duplicate of this form for their records. Accurate completion of this form is required for warranty coverage and for any technical support by Spark Modern Fires.

Date Purchased:

Purchaser/Dealer:

Installer:

Fireplace S/N on product ID tag:

Date Installed:

FUEL:

Natural Gas

Inlet Pressure Measured After Installation:

L.P. Propane

Manifold Pressure Measured After Installation:

High Fire:

In. W.C.

Low Fire:

In. W.C.

In. W.C.

ALTITUDE:

Feet Above Sea Level

Was Stove Derated?

Yes

No

SMF22013

NOTES

The installer should complete the form below that describes the details of the installation. Having this written record of installation information available will greatly expedite trouble-shooting should any problem arise with your fireplace. The installer should keep a duplicate of this form for their records. Accurate completion of this form is required for warranty coverage and for any technical support by Spark Modern Fires.

Date Purchased:

Purchaser/Dealer:

Installer:

Fireplace S/N on product ID tag:

Date Installed:

FUEL:

Natural Gas

Inlet Pressure Measured After Installation:

L.P. Propane

Manifold Pressure Measured After Installation:

High Fire:

In. W.C.

Low Fire:

In. W.C.

In. W.C.

VENTING:

Please Verify The Brand And Model Of Venting Used:

Vent Termination (Cap):

Horizontal

Vertical

Vent Cap Model No:

CONFIGURATION:

Total Horizontal Run:

Total Vertical Run:

Quantity 90° Elbows:

Quantity 45° Elbows:

Feet/Inches

Feet/Inches

ALTITUDE:

Feet Above Sea Level

Was Stove Derated?

Yes

No

If Yes To What Orifice Size?

Unusual Structure Near Vent?

Inside Corner

Trees/Shrubs

Other

Termination:

(Please Describe)

Snorkel

Vent Configuration Sketch Required Below:

Prevalent Wind Conditions?

Other Installation Notes:

WARRANTY INFORMATION

Model:

Serial No.:

Always specify model and serial numbers when communicating with the factory.

LIMITED LIFETIME WARRANTY

The following components are warranted for life to the original owner, subject to proof of purchase: Firebox, Combustion Chamber, and Steel Burner.

BASIC WARRANTY

Spark Modern Fires warrants the components and materials in your gas appliance to be free from manufacturing and material defects for a period of two years from date of installation. After installation, if any of the components manufactured by Spark Modern Fires in the appliance are found to be defective in materials or workmanship, Spark Modern Fires will, at its option, replace or repair the defective components at no charge to the original owner. Spark Modern Fires will also pay for reasonable labor cost incurred in replacing or repairing such components for a period of two years from date of installation. Any products presented for warranty repair must be accompanied by a dated proof of purchase.

This Limited Lifetime Warranty will be void if the appliance is not installed by a qualified installer in accordance with installation instructions. The Limited Lifetime Warranty will also be void if the appliance is not operated and maintained according to the operating instructions supplied with the appliance, and does not extend to (1) firebox/burner assembly damaged by accident, neglect, misuse, abuse, alterations, negligence of others, including the installation thereof by unqualified installers, (2) the costs of removal, re-installation or transportation of defective parts on the appliance, or (3) identical or consequential damage.

All service work must be performed by an authorized service representative.

This warranty is expressly in lieu of other warranties, express or implied, including the warranty of merchantability of fitness for purpose and of all other obligations or liabilities.

Spark Modern Fires does not assume for it any other obligations or liabilities in connection with sale or use of the appliance. I n states that do not allow limitations on how long an implied warranty lasts, or do not allow exclusion of indirect damage, those limitations of exclusions may not apply to you. You may also have additional right not covered in the

Limited Lifetime Warranty. Spark Modern Fires reserves the right to investigate any and all the claims against this Warranty and decide upon method of settlement.

For information about this warranty contact:

SPARK MODERN FIRES

99B Greenwood Ave Bethel, CT 06801 USA P. 203.791.2725 F. 203.798.8661

WWW.SPARKFIRES.COM

Rev. No:

12

/201

9

advertisement

Related manuals