Shiro SC3122 User Manual

• User Manual •

SC3122

Caller ID Phone

SC3122 User Guide

!

• Please ensure the phone is placed in a dry and ventilated place without corrosive air.

• Please install 3 x AA batteries for viewing the LCD display. If the LCD does not display clearly, please change the batteries.

• Before operation, please check if you had applied for caller ID service from Telecom for caller ID display.

FEATURES

：

• FSK/DTMF dual system

• 40 incoming call memories, call back function

• 10 outgoing call memories and conversation time review and redial back

• Long distance area code setting

• Local area code filter

• Pre-dial and edit dialing number

• LCD display of year, month, date and time

• 4 ringing tone selection

• IDD Lock function

• Pulse/Tone and time function

• Ringer Hi/Lo function

• Handsfree Speakerphone Hi/Lo function

• Alarm function

1

SC3122 User Guide

TABLE OF CONTENT

PRODUCT OVERVIEW.....................................................................................3

1. INSTALLING OR REPLACING THE BATTERY .........................................................4

2. SWITCH OPERATION...................................................................................4

IDD LOCK switch.......................................................................................4

RING HI/LO switch ....................................................................................4

VOLUME HI/LO switch ................................................................................4

3. SOFTWARE SETTING ..................................................................................5

4. Function key operation ..............................................................................6

UP key ..................................................................................................6

OUT key ................................................................................................6

DEL key .................................................................................................6

REDIAL key .............................................................................................6

FLASH (600ms) / RING key ...........................................................................6

HANDSFREE (HF) key..................................................................................6

5. ADDITIONAL NOTES ...................................................................................6

INCOMING CALL LCD INDICATOR .....................................................................6

TROUBLESHOOTING GUIDE..............................................................................7

DECLARATION OF CONFORMITY ........................................................................7

2

SC3122 User Guide

PRODUCT OVERVIEW

11

10

9

12 13 14

8

Description:

2. IN USE Led 12. TEL LINE jack

3. RING Led 13. VOLUME (HF) HI/LO Key

4. SET key 14. RING HI/LO Key

5. FLASH/RING

7. HANDSFREE (HF) key

9. UP

10. DEL KEY

3

1

2

3

4

5

6

7

SC3122 User Guide

1. INSTALLING OR REPLACING THE BATTERY

Install 3 Alkaline AA batteries into the battery compartment and re-fit the cover before use.

IMPORTANT —before removing the battery compartment cover, ensure the base unit is disconnected from the telephone line.

Connection and conditions for use

You can connect your SC3122, to public networks in the United Kingdom or to an approved PBX using DTMF signaling. Each item of telephone equipment (phones, fax machines, etc.) has a ringer equivalence numbers (REN) . The RENs of all equipment connected to an exchange line must not add up to more than 4 otherwise, one or more phones may not ring and/or answer calls correctly.

SC3122 has a REN of 1, and most other telephones have a REN of 1 unless marked otherwise.

2. SWITCH OPERATION

IDD LOCK switch

Use the keys provided in the package. The telephone allows all outgoing number if the key is on red point. It cannot dial outgoing number starting with digit 0 when the key is on green point.

RING HI/LO switch

Select your preferred ringing tone either HI or Lo. The selection is at the back of the telephone.

VOLUME HI/LO switch

Select your preferred handsfree speakerphone volume either HI or Lo. The selection is at the back of the telephone.

4

SC3122 User Guide

3. SOFTWARE SETTING

Press SET key to enter menu setting, the phone LCD will display SET 1 DATE , press UP key to select different options. Press SET key again to confirm. Use UP key to select the mode you need. After completing the setting, press SET key to go to the next item. To exit menu, press

DEL key.

By pressing SET key (in the on-hook mode), you can select the following:

SET ITEM OPERATIONS

DATE/TIME LCD displays , press SET key to enter this mode. The year value would flash, use UP key to select value, then press SET key to move to next item.

AREA CODE LCD , press SET key to confirm, LCD display

CODE , press SET key to enter this mode. Use UP key to select value, then press SET key to move to next item.

Area Code is used to filter the number for incoming calls. E.g. Area code = 75 when there’s incoming call with 75 6554556, it will be displayed as 655 4556 only.

LONG CODE LCD panel display SET 3 LCODE , press SET key to enter this mode. LCD displays LCODE , use UP key to select value, then press SET key to move to next item.

To activate this feature, while checking incoming calls using UP key, press REDIAL key twice to add the LONG DIST ACCESS code in front of the number.

FLASH TIME

AUTO-IP

LCD panel display SET 4 FLASH , press SET key to enter this mode. Use

UP key to select value, then press SET key to move to next item.

LCD display SET 5 IP , press SET key to enter this mode. LCD display

AUTO IP OFF and OFF will flashes, use UP key to select value. When

LCD displays AUTO IP ON , press SET key. Then the LCD will display

INPUT CODE for you to enter the IP numbers. Use DEL key to correct any wrong input. After entered all IP number, press SET key to enter into next item. The outgoing call will automatically use IP mode.

Auto IP allows you to replace a sequence of number with single 0. E.g.

Setting 1455 as Auto IP, therefore when you need to dial 1455, just put

0 in front (pre-dial mode), 0 2334565 will be dialed as 1455 2334565.

P/T MODE

ALARM

LCD display SET 6 P-T , press SET key to enter this mode. LCD display

TONE . Use UP key to change it into PULSE , press SET key to move to next item.

LCD display SET 7 ALAR , press SET key to enter this mode. LCD display

5

SC3122 User Guide

ALARM OFF means this function is off. Use UP key to select ON or OFF

The alarm feature is to ensure other telephone is unable to use the same line as your SC3122. Once activated, any other telephone connecting to the same line cannot call out at all and when listening to incoming call, there will be constant noise.

4. Function key operation

UP key

In any mode, press UP key to check all the incoming numbers. If there is no incoming number, the unit will display END . The unit can receive up to 16-digit phone numbers.

OUT key

In any mode, press OUT key to check the outgoing numbers with time. Press REDIAL key to dial the selected number.

DEL key

In any mode, when checking the incoming and outgoing call, press DEL key to delete the number you are checking. Press and hold DEL key for 4 sec and it will delete all incoming call or outgoing call numbers. When you pre-dial, press DEL key to delete one digit one by one.

When you enter IP number or password, use DEL key to delete error digit.

REDIAL key

In the on-hook mode, press this key to redial the last dialed number.

FLASH (600ms) / RING key

In the on-hook mode, press FLASH/RING key, the phone LCD will display TONE 1-4 , which means there are four selectable ringing tones. Select your preferred ringing tone by pressing

FLASH/RING . When LCD panel displays TONE OFF , it means the ringing tone is turned off.

In the on-hook mode, press this key to auto-hang up for 600ms, after that you can press

REDIAL key or dial out another number.

HANDSFREE (HF) key

While on-hook, press the HANDSFREE key to go into handsfree mode. You can talk through the microphone and listen from the speakerphone without lifting the handset. While off-hook, press the HANDSFREE key and put down the handset to go into handsfree mode.

5. ADDITIONAL NOTES

INCOMING CALL LCD INDICATOR

When there is incoming call, the unit will be automatically display the caller number, date and time, and also display its serial number. If the incoming call is in private mode, it will display “__p__”; it will display “__0__” if exchange cannot determine the number; it will display “—E—“ if the call signal contains error.

6

SC3122 User Guide

TROUBLESHOOTING GUIDE

(Q) I do not hear any dial tone from the handset.

(A) Ensure the handset cord is connected correctly from the handset to the handset cord jack at the base. Ensure you have plug in the telephone cable from the telephone to the wall socket correctly. If the problem persists, please check with your local dealer.

(Q) I could not see the caller’s number on the LCD when there is incoming call.

(A) Ensure that you have subscribed Caller ID service from your local telecom provider.

(Q) There is no LCD Display / Backlight after I have connected the telephone line. I can call out normally.

(A) Ensure that you have inserted the batteries on the battery compartment. If there is still no display, change the batteries and ensure it is not empty. If the problem persists, please check with your local dealer.

DECLARATION OF CONFORMITY

The telephone complies with the essential protective requirements and objectives of:

• EC R& TTE Directive 1999/5/EC

• EC Low Voltage Directive 73/23/EEC

• EC EMC Directive 89/336/EEC

And conforms to the following relevant harmonized standards:

• EMC: EN55022, EN55024

• Safety: EN 60950

Created on 28 th October 2005. SC3122 Caller ID Phone.

Please visit us at www.shirocorp.com

.

7