Wisycom MTP40S User Manual

Add to My manuals
24 Pages

advertisement

Wisycom MTP40S User Manual | Manualzz

MTP40S User Manual

Wideband Wireless

Professional Pocket

Transmitter

SN: ________________

Rev.07 (ref. FW 1.30.0P)

Date: 01 February 2018

MTP40S User Manual

I

NTRODUCTION

“MTP40S is an extremely small and light pocket transmitter especially designed for professional wireless microphone applications”

Very easy and quick to use thanks to OLED display, dedicated buttons and a joggle selector.

MTP40S benefits also of the latest Wisycom RF technology along with an enhanced robustness against noise and inter-modulation.

Fig. 1

Turn on wireless:

Move the Wireless

power switch

in

“I” position.

1

Turn on display:

Push <select switch> and hold it.

Open MIC Body:

Push the side buttons and flip down the cover, to access internal setup controls and batteries.

❶ Switch to enable wireless transmission, it also indicates the battery status and peak/mute operation (with PTT)

❷ In order to allow front visibility same colour information on (1) is replicated with this LED

Oled display for transmitter setup

❹ <

ch

>, <

gain

> and 3 positions <selector>

Battery holder

❻ Cover (to open push side buttons)

1.

Front LED RGB.

6

5

4

Fig. 2

2

2

3

MTP40S User Manual

S

AFETY INSTRUCTION

Read this safety instruction and the manual first

Follow all instructions and information.

Do not lose this manual.

Do not use this apparatus under the rain or near the water.

Do not install the apparatus near heaters or in hot environments, do not use outside the operating temperature range.

Do not open the apparatus, only qualified service technician are enabled to operate on it. The apparatus needs servicing when it is not properly working or is damaged by liquids, moisture or other objects are fallen in the apparatus.

Use only accessories or replacement parts authorized or specified by the manufacturer.

Clean the apparatus only with dry cloths, do not use liquids.

Report the serial number and the purchasing date in front of the manual. It is needed to have proper replacement parts or accessories from the manufacturer.

When replacement parts are needed, use only replacement parts authorized from the manufacturer. Substitution with not authorized parts could result in electric shock, hazards or fire.

Keep attention on all the labels with warnings or hazards on the apparatus.

L

ED INDICATIONS

Led indication with LED RGB (

red

,

green

,

blue

) in front led ( ❷ ):

- Wireless transmission status:

Green

when RF transmission power is on (on power on the device, this LED is

red

and become green when the RF transmission power is on).

- Battery status:

green

steady, slowly blinking (< 25%), quickly blinking (<12%).

- Modulation peek (if activated and the limiter is disabled):

red

.

- Ptt status:

red

if active (push to talk “pushed”).

- Limiter in action (if activated):

blue

.

B

ATTERIES

MTP40S is working with 2 AA alkaline, NiMH or Lithium batteries (select correct type on setup controls). Battery status can be checked on internal OLED display or looking the LED status on front

❷ .

BATTERY SUBSTITUTION

Open transmitter cover and insert batteries following polarity indicated.

Attention: always replace both the batteries

3

MTP40S User Manual

P

OWERING UP

Move the wireless power switch (see Fig. 1) in “I” position to activate wireless transmission: the front LED ❷ lights up red and then green when the RF transmission power is on (blinking when battery is low!)

S

ETUP CONTROL

Open transmitter Body to access the “display and controls” area (Fig. 3):

A.

Graphics Display (

OLED

)

B.

Channel selection buttons (

ch

)

C.

MIC gain setup buttons (

gain

)

D.

3 position selector (

up

/

down

/

click

)

+

CLICK

-

A

B

C

D

Fig. 3

OLED POWER UP (OLED IS IN OFF CONDITION)

Pushing down selector (

click

), oled turns on. A first menu with serial NO and brand logo is displayed, then <status> menu enters automatically.

Pushing and holding selector, serial NO menu is displayed.

OLED POWER DOWN (OLED IS IN ON CONDITION)

Display turns off automatically after 15 sec, unless in <AUDIO> menu (with audio level < 5% from nominal).

4

MTP40S User Manual

DISPLAY MENU

Setup menu are accessed in sequence:

STATUS

PRESET

TUNING

Current

Load

Save

CH

GR

Freq

AUDIO

RF/Battery

LED

MIC

Name

Info

IRDA

Lock

*

Depending on the Power Profile

AF In Gain

AF Level

Phase

HPass Filter

Noise R.

Limiter

RF Power

Battery

Led Light

Led Mode

Mode

PTT

FACTORY/USER/PRESET1/2/3/4/5/6/7/8

USER

00-59

00-39

1: 470.000÷640.000

2: 566.000÷798.000

3: 510.000÷698.000

-60 ÷ +40 dB (1dB step)

-54 ÷ +46 dBu (1dBu step)

0/180

Flat/60/80/120/170/250/400Hz

ENR-Wisy/ENC-Wisy

On/Off

10/50/100mW *

Alkaline/NiMH/Lithium

0

÷

16

None/ModPeak/PTT

2 wires/2wires+bias/3 wires/

2wire&pha/2w+bias&pha

Disable/Normal/Muting/No Data

Preset parameters

5

MTP40S User Manual

Using <+/-> selector all menus can be accessed in sequence, push <click> to enter edit mode (in the left side of the display appear the word EDIT and the parameter start blinking):

+

CLICK

-

<+/-> to setup field

<click> again to confirm changes and exit.

exit without confirmation

if no button is pressed after a few seconds time out.

<START UP> menu

These menus are displayed during power up for few seconds.

First one gives information of antenna to be used. The number displayed is the center-band of the antenna to be used.

The second menu gives indication on product:

- product id (MTP40S),

- the firmware release (ex. 1.30.0A),

- the band in extended format and

- the serial number.

Keep selector pushed to hold this menu!

<STATUS> menu

This is the first menu displayed after power up.

Major info are displayed:

-

Current channel/group (i.e. CH:00 GR:39)

-

Current frequency (i.e. 566.000 MHz)

-

Mic gain (i.e. AF: +00 dB) and high pass filter (i.e. HP:60 Hz)

-

“RF 100” or RF 50” or “RF 10” on top right if RF transmission is active respectively at 100mW or 50mW or 10mW

-

On left, battery bar is displayed

<PRESET> menu

This menu can be entered by scrolling selector, or pushing

at the same time

both quick channel setup buttons (<

ch

> &

<gain>

).

MTP40S can recall configuration presets. “FACTORY” recalls the

Wisycom factory configuration. “USER” recalls the user configuration (the transmitter configuration is copied into the

USER using the “save to” submenu). All “USER” menus are not locked by default, thus this is quick way to unlock features!

When the user changes some parameters from the PRESET configuration (for less than frequency) a star appears on the topright corner until a save command is executed.

The other 8 configuration presets are user programmable thru the infrared and the PC interface

(using the programmer UPK 300/UPK

Mini

or the receiver MRK950/MRK960).

We provide the device with some preset configurations specifically designed for certain types of microphone or applications (it’s possible to change these presets in any time using the TX manager).

All parameters can be “left unchanged”, “changed” or “changed and lock”, allowing a very flexible way to pre-program MTP40S configuration.

6

MTP40S User Manual

<TUNING> menu

This menu can be entered by scrolling selector or using

quick channel setup

buttons (<

ch

>).

In this menu current channel/group and frequencies can be setup.

The name of the group is shown on the top right of the display.

Sync

group is a quick self-settable channel synchronized by receiver

(with SYNC group, on the top right of the display is shown the name of the synchronized receiver).

Use the selector to change values (<

+/-

>) and <

click

> to confirm.

Using quick channel setup buttons (<

CH>

), it is possible to enter quickly in the tuning menu. Note that the menu has a different layout (see the side image)

<AUDIO> menu

This menu can be entered by scrolling selector or using quick gain setup buttons (<

gain>

).

The sensitivity of the audio input is settable between “

AF Gain

(measured in dB) or “

AF Level

” (measured in dBu).

To help proper audio gain setting, an audio bar is supplied (with maximum peak indicator) indicating the headroom to audio peak

(0 dB , nominal deviation 40KHz).

Set the gain, with the maximum input signal, avoiding the peak on the audio bar.

TRY TO SETUP TO HAVE A MAX PEAK HOLD BAR CLOSE TO -6dB

.

Using quick gain setup buttons (<

GAIN

>), it is possible to enter quickly in the audio gain menu. Note that the menu has a different layout (see the side image)

The second <AUDIO> menu allows to set:

- Audio phase: 0° or 180°

Note:

Since common "2-wires + bias" microphones invert the phase, when the MIC mode of the transmitter is set to “2wires+ bias”, the phase is automatically inverted and so the complete system (MTP4x+MIC) has 0° phase (an asterisk appear on the display near the phase to indicate that the phase was inverted).

-High Pass Filter: applies different audio HP filter: Flat/ 60Hz/

80Hz/ 120Hz/ 170Hz/ 250Hz/ 400Hz.

The third <AUDIO> menu allows to set:

-Noise reduction:

ENR-Wisy:

designed for maximum noise reduction

ENC-Wisy:

designed for maximum audio fidelity (use this in case of special vocal application or to remote instruments)

-Limiter: if is set “On”, an input audio signal above the peak threshold (

up to 30 dB above peak

) is not cut but attenuate, without lost quality. The limiter acts as a variable attenuator (thanks to the feedback system), maintaining a distortion <3%.

When the limiter intervene, the front led turns blue.

If this parameter is set “Off”, the limiter is disable.

7

MTP40S User Manual

<RF/BATTERY> menu

This menu can be entered by scrolling selector.

RF power can be setup to 10mW, 50mW or 100mW (depending on the Power profile).

Use the Battery menu to select the type of battery used.

MTP40S support Alkaline/NiMH/Lithium battery type.

Use the selector to change values (<

+/-

>) and <

click

> to confirm.

<LED> menu

This menu can be entered by scrolling selector.

Led Light allows to change the brightness of the front led (0÷16) .

Led Mode:

- None: allows to disable modulation peak LED on front led

(the red light)

- ModPeak: allows to enable modulation peak LED on front led

(become RED when audio get close to saturation when the limiter is not enable)

- PTT: allows to enable RED color on front led when PTT button is pushed.

<MIC> menu

This menu can be entered by scrolling selector.

Mode

: Following Mic mode can be setup (for LEMO option)

-2 wires:

(PTT is possible) for external audio input

-2 wires + bias:

(PTT is possible) for most 2 wires MIC

-3 wires:

(no PTT) for most 3 wires MIC

-2 wires & pha:

to connect a wired mic thru a 48V adapter

(PHA48)

-2 wires+bias & pha:

Allow to connect a ‘2 wires + bias’ MIC or a ‘2 wires & phantom’ MIC

(with PHA48)

PTT

setting defines how and what information the transmitter has to send in normal use or when the PTT button is pushed.

- Disable

: when the PTT button is pushed, nothing happen. (the transmitter sends AF+Tone squelch)

- Normal

: when the PTT button is pushed, the transmitter send a different RF signal. According to the receiver configuration the audio can be enabled/disable on LINE (and/or COM).

- Muting

: the transmitter doesn’t send the audio. The voice is cut, it doesn’t enter to the microphone

- No Data

: the transmitter sends neither tone squelch nor battery data.

Use the selector to change values (<

+/-

>) and <

click

> to confirm.

NOTE: For DPA option (2 pin microdot audio connector), even if the MIC mode menu allows to set one of the 5

MIC modes, only

2 wires

or

2 wires+bias

mode are possible.

<NAME> menu

This menu can be entered by scrolling selector.

In this menu it’s possible to see the frequency set on the device and the name of the transmitter.

It’s possible to enter on this menu also pressing at the same time the CH/GAIN buttons ( B + C )

8

MTP40S User Manual

<INFO> menu

This menu can be entered by scrolling selector.

In this menu it’s possible to see:

-

FW version

-

HW version

-

Serial number

-

Bandwidth

-

Bootloader version

-

Option

<IRDA> menu

This menu can be entered by scrolling selector.

While there is this menu, the device can be connected to IRDA for setup or firmware upgrades.

Note: if the IRDA interface is enabled and there’s no communication for around 10 seconds, the IRDA interface is automatically turned off.

On power on the device, the IRDA interface is enabled for 14 seconds.

<LOCK> menu

This menu can be entered by scrolling selector.

Long pressing (2 sec.) selector button (

click

) it locks MTP40S in transmission mode.

To unlock, long pressing (2 sec.) selector button again.

<BOOTLOAD> menu

This menu can be entered by turning on the transmitter while pushing

at the same time

both quick channel setup buttons (<

ch

> &

<gain>

) or connecting the device via IRDA using the IR Programmer for

FW update

Device is forced in bootloader mode to allow

FIRMWARE UPDATE

.

9

MTP40S User Manual

The following table sums up which parameters can be set and the related range settings.

MENU

PARAM

ETER

CH

GR

MEANING

Channel

Group

RANGE SETTINGS

TUNING

AUDIO

RF/BATTERY

Freq

AF In Gain

AF Level

Phase

HP Filt.

Noise R.

Limiter

Battery

Frequency

Gain of the audio signal

Audio signal phase

High Pass filter

Noise reduction

Limiter

RF Power RF Power

0 ÷ 59

0 ÷ 39 + SYNC GROUP depends on the MTP40S Model:

1 470-640

2

3

566-698

510-698

-60dB ÷ +40dB step of 1dB

-54dBu ÷ +46dBu step of 1dBu

0° or 180°

Flat/60/80/120/170/250/400 Hz

ENR: Wisycom Extended-NR, noise optimized

ENC: Wisycom Extended-NC, voice optimized

On/Off

10mW or 50mW or 100mW (depending on the power profile)

Alkaline, NiMH or Lithium

LED

Led Light

Led Mode

Battery type

Power switch green brightness

It defines when the power switch led

(see Fig. 3) has to become RED

0 ÷ 16

None: never

ModPeak: when audio get close to saturation

PTT: when the PTT button is pushed

MIC

Mode

PTT Mode

MIC type

It defines how and what information the transmitter has to send

’2 wires’

‘2 wires + bias’

‘3 wires’

‘2 wires & phantom’

‘2 wires + bias & phantom’

Disable

:when the PTT button is pushed, nothing happen. (the transmitter sends AF+Tone squelch)

Normal

: when the PTT button is pushed, the transmitter send a different RF signal. According to the receiver configuration the audio can be enabled/disable on LINE (and/or COM).

Muting

: the transmitter doesn’t send the audio. The voice is cut, it doesn’t enter to the microphone

No Data

: the transmitter sends neither tone squelch nor battery data.

10

MIC Mode setting (only for LEMO option):

MIC Mode:

’2 wires’:

Pin out

1=GND

3=AF

‘2 wires + bias’:

‘3 wires’:

‘2 wires & phantom’:

1=GND

3=AF+5.5V

1=GND

2=5.5V

3=AF

1=GND

2=3.1V (power for

PHA48)

3=AF

1=GND

2=3. 1V (power for

PHA48)

3=AF+5,5V

‘2 wires + bias & phantom’:

3 PIN LEMO CONNECTOR

(use FVB.00.003.NLN on Mic)

Gain

-60/40 dB

-60/40 dB

-60/40 dB

-60/40 dB

-60/40 dB

PTT

Disable

Normal

Muting

No data

Disable

Normal

Muting

No data

Disable

No data

Disable

No data

Disable

No data

MTP40S User Manual

Led Mode

None

Mod. Peak

PTT

None

Mod. peak

PTT

None

Mod. peak

None

Mod. peak

None

Mod. peak

11

MTP40S User Manual

ACCESSORIES AND PARTS

AWF30-B1-507

For MTP40S-

X

-

X

1

Band 470 ÷ 547 MHz

Antenna Code label 507

AWF30-B1-590

For MTP40S-

X

-

X

1

Band 547 ÷ 640 MHz

Antenna Code label 590

AWF30-B2-616

For MTP40S-

X

-

X

2

Band 566 ÷ 672 MHz

Antenna Code label 616

AWF30-B3-552

For MTP40S-

X

-

X

3

Band 510 ÷ 595 MHz

Antenna Code label 552

AWF30-B2-732

For MTP40S-

X

-

X

2

Band 672 ÷ 798 MHz

Antenna Code label

AWF30-B3-646

For MTP40S-

X

-

X

3

Antenna Code label

732

Band 595 ÷ 698 MHz

646

CAL48

Cable to connect an MTP30 (with option /PHA) or

MTP40/40S to a PHA48 to use microphone with

XL3/48V connection

CAL120

AF cable (120cm), LEMO 3pole / XLR-3F connectors

PHA48

Plug-on for XLR3 Mic with 48V Phantom power.

To be used with CAL48 (connected to an MTP30/40/40S)

NEW REV2 with 4mA Phantom current!

ADT40

Power Adapter for MTP30/40/40S.

Power input: 9-18V DC feeding (internal switching regulation).

Variants:

ADT40: without connector (pigtail)

(Shield= GND ,

Blue Red

= Vdc)

ADT40X: with XLR-4pin power connector

ADT40H: with Hirose-4pin power connector

NOTE: MTP30/40/40S must have ADT option to pass thru cable

UPK300E / UPK

Mini

Infrared programming kit

(interface + software) USB interface

UPK300E

12

Antenna Code label

UPK

Mini

MTP40S User Manual

H

OW TO USE

W

ISYCOM

TX M

ANAGER

Wisycom TX Manager allows to read, modify and update the configuration of Wisycom transmitters.

It is necessary to

 connected the programmer UPK300E/UPK

Mini

or the receiver MRK950/MRK960 to the PC thru

USB connection

 run the Wisycom TX Manager

 enable the IRDA communication on the transmitter (see IRDA menu)

NOTE: Wisycom IR Programmer doesn’t work whit MRK950/MRK960 if it is connected to the PC using an Ethernet cable.

The Wisycom IR Programmer’s window is divided in 4 parts (see the image below):

Interface

and

Device

panel contains all the major information of the connected

d

evice

Current Settings

panel shows the current configuration. Thanks the PRESET panel, a previous saved configuration can be chosen and loaded like current setting.

Tuning Frequencies

panel allows to handle Groups, Channels and Frequencies

Presets

panel allows to read, change and save different configurations

❶ ❷ ❸ ❹

13

MTP40S User Manual

10 different configurations are available:

• FACTORY configuration is a locked configuration: no parameter can be changed.

USER configuration is the only configuration that can be saved using the OLED display (see

<PRESET> menu). Note: It is not possible to change the name of this configuration.

Other 8 configurations where the user can change both the name and the values of all parameters.

INTERFACE AND DEVICE PANEL (

)

At the beginning, the program checks which IR devices are detected and they appears on the

Interface

panel.

The user has to select the device and push <connect> button in order to open the communication with the IR device. A picture on the top in the Interface panel help the user in this selection showing the type of devices detected. During this process the “IR activity” led blinks to indicate that the program wait connection’s answer from the IR device.

A successful connection is signaled with the “interface connection” green led, while a failed connection is signaled with the “communication error” led.

Once a supported device is found, the software automatically reads all the data related to the remote configuration, as well as the frequencies that are pre-programmed.

Firstly, in order to avoid unwanted operation, no parameters can be changes and the EDIT button, presents on the bottom of

Device

panel, is yellow and set to LOCKED state. Pushing the EDIT button, it becomes grey and sets to UNLOCKED state to indicate that the configurations can be modified.

In this panel it’s possible to assign a name to the TX (not available for FW v.1.22.0F or previous).

Under this parameter, there is a flag to hide the info menu on the TX (not available for FW v.1.22.0F or previous)

CURRENT SETTINGS PANEL (

)

In the Current Settings panel the user can

 with Preset panel → load one of the 10 available configurations

 with other panels → modify all the configuration’s parameters (the same that are changeable in the OLED display). Each parameter can be locked or hidden clicking the related lock/hidden button, so the set value cannot be changed next or cannot be visible on the OLED display.

ATTENTION: All the modifies applied to the Current Settings panel are instantaneous: they are applied directly to the device and save in its memory but no saved in the preset configuration.

14

MTP40S User Manual

TUNING FREQUENCIES PANEL (

)

With the Tuning Frequencies panel the user can select a frequencies group (0÷39) and for each one execute the following operations:

modify the Group’s Name

lock and/or hidden the group

for each channel (0 ÷59) of the selected group: change the frequency value and the related status (locked/hidden) (in the center grid frequency)

The SAVE button, at the top of the panel, save the changes of the group selected

(name group, lock/hidden group).

To change a frequency value for a specific channel: double click on the grid frequency panel (row=channel’s number), insert the new frequency value and press OK button.

To lock/hide a specific channel, double click on the grid frequency panel.

NOTE: keeping pressed the CTRL button on the keyboard and clicking the wanted channel/group shown on the frequencies grid, the tuning process is executed. It is equivalent to configure the

Tuning in the Current Settings panel but it is easier. The device is re-tuned immediately, so be sure that the RF power is turned off while changing frequencies with other RF systems in use around you!

15

MTP40S User Manual

If the currently tuned channel is on the same group that is listed on the grid, the background color of the related cell (channel) on the grid becomes yellow.

Using the LOAD/SAVE button, at the bottom of the panel, it is possible to

load/save

the frequencies for the selected group from/to a .wdf file. To save the frequencies of all the groups click to the related button above. The legacy option save the channels without the hidden/lock info.

16

MTP40S User Manual

PRESETS PANEL (

)

The Preset panel allows to manage all the 10s available configurations.

For each configuration it is possible to set the name and all the parameters value except for

FACTORY and USER configurations (see table below).

PRESETS:

FACTORY

USER

OTHERS

NAME*

LOCK/DON’T CARE PARAMETERS

VALUE

√=change is allowed

* Be careful to write a meaningful name for the preset because the name will appear on the settings list of the device menu! Please, avoid empty names.

If a parameter is “locked”, it cannot be modified by device menu (using OLED display), while if “don’t care” propriety is active, when the user load the configuration, the parameter’s value doesn’t changed.

ATTENTION: Changes are applied only after a “save” action.

NOTE:

“a trick

” In case of the user have a locked parameter and he is in great need for modify it, he can save the configuration to USER configuration by OLED (see PRESET menu) and then load the

USER configuration (in this way all the parameters have the lock propriety disable and the user can modify all the parameters).

FILE MENU

Using a file menu at the top left of the panel it is possible to

load/save all the configuration

values of the device to/from a .wcf file (Wisycom

Configuration File).

Save a .wcf file

With an infrared device correctly connected, select File->Save User Configuration and select the destination file.

Load a .wcf file

To load a user configuration select File->Load User Configuration and select a previously saved data file; a form will be shown, where it's possible to select which data has to be restored and which skipped. This allow the user to load a particular configuration while keeping other data.

17

MTP40S User Manual

TECHNICAL SPECIFICATIONS

Switchable channels

Switching window

Frequencies

Frequency stability

Temp. range

Max RF power

Spurious emissions

Modulation

Nominal deviation

Telemetry feature

AF input connector

LEMO option

2400 allocated by 40 groups of 60 channels (in specific frequency range), quickly selectable with dedicated buttons

Up to 232 MHz, depending on band (see

Variants

on the next page)

Quartz PLL frequency synthesizer circuit (25 kHz step)

± 2,5 ppm (in the rated temperature range)

-10 ÷ +55 °C

10mW (ERP) (to respect some local norm)

50 mW (ERP) (note: in some countries middle power can be disabled, for local norm!)

100 mW (ERP) (note: in some countries high power can be disabled, for local norm!)

< 2 nW wideband FM, with pre-emphasis

±40 kHz (Peak deviation = ±56 kHz)

MTP40S transmits also a digitally modulated sub-carrier, suitable for:

tone-squelch operating

remote battery monitoring

optional PTT (push to talk) operation

Configurable on ‘mic’ display menu in 5 options:

’2 wires’

:

‘2 wires + bias’

: gain selectable -60 ÷ +40 dB (-54 dBu ÷ +46 dBu peak), no bias voltage gain selectable -60 ÷ +40 dB (-54 dBu ÷ + 46 dBu peak), 5.5 V on 4k7 bias supply

‘3 wires

:

‘2 wires & phantom’

‘2 wires + bias & phantom’:

gain selectable -60 ÷ +40 dB (-54 dBu ÷ +46 dBu peak) gain selectable -60 ÷ +40 dB (-54 dBu ÷ +46 dBu peak), gain selectable -60 ÷ +40 dB (-54 dBu ÷ + 46 dBu peak), 5.5 V on 4k7 bias supply

AF input level

Max. input level

Noise-Reduction

AF bandwidth

Distortion

Signal-to-noise ratio

Led

Display

PTT function

Power supply

MTP40S Battery life

(2 AA alkaline)

100 dB adjustable range from -54dBu (775 uV) to 46dBu (15.5 V) at peak deviation (1kHz), adjustable in 1 dB steps

+46 dBu (15.5 V) at clipping, +20 dBu (7.75 V) at nominal level

ENR (Wisycom Extended-NR), with independent Attack- and Recovery-time, noise optimized

ENC (Wisycom Extended-NC), with independent Attack- and Recovery-time, voice optimized & with reduced pre-emphasis

45 Hz ÷ 21 KHz (3dB)

55 Hz ÷ 20 KHz (1dB)

< 0.3 % (0.15 % typ.)

typ. 115 dB (A) rms

with 40 kHz deviation

typ. 121 dB (A) rms

with 56 kHz deviation

Led indication with RGB led (red, green, blue) on wireless power switch:

Wireless transmission status:

GREEN

on/off

Modulation peek (if activated & the limiter is disabled):

RED

Battery lifetime status:

GREEN

- steady (> 25%)

- slowly blinking (< 25%) - quickly blinking (<12%)

Ptt status:

RED

if active

Limiter into action: Blue

High contrast OLED (Organic light-emitting diode) white display (128 x 32 pixels)

8 step battery lifetime indication: 7 bars (100%-87%-75%-63-50%-38%-25%) and “empty bar” quickly blinking (12% remaining)

Pin 3 of the AF connector can be setup to an external push button

2 AA size batteries (Alkaline, rechargeable NiMH or Lithium)

approx. 14 hours @ 10mW continuous working

approx. 10 hours @ 50mW continuous working

approx. 7 hours @ 100mW continuous working

73 x 61 x 17.5 mm (Height-Width-Depth) without clip

Approx. 80 g. without batteries (120g with batt.)

Dimensions

Weight

18

MTP40S User Manual

MTP40

S

Note: unit is mm

POWER PROFILE & COUNTRY

FREQUENCY RANGE:

EU

max power 50mW (Europe)

VARIANTS:

▪ AUDIO CONNECTOR

LM

3 PIN LEMO CONNECTOR

DP

2 PIN DPA MICRODOT CONNECTOR

0W1 / EUX

max power 100mW (Europe)

US

max power 50mW (USA)

USX

max power 100mW (USA & Canada)

▪ COLOR

PV

body color titanium gray (ceramic coating)

JP

max power 10mW (Japan)

NZ

max power 100mW (New Zealand)

CN

max power 50mW (China)

BL

body color black (powder coating)

▪ FREQUENCY RANGE

B5

470-654 MHz

B2

566-798 MHz

OPTIONS:

ADT

hole on battery housing for ADT40

B3

510-698 MHz

For commercial code, see Variants area of Wisycom Products on website

19

MTP40S User Manual

Compliance

Model

MTP40S

MTP40S-EU

MTP40S-0W1

MTP40S-EUX

In Compliance with

EN 301 489-1/-9

EN 600065

EN 300 422-1/-2

EN 301 489-1/-9

EN 600065

EN 300 422-1/-2

EN 300 454-1/-2

MTP40S-US

MTP40S-USX

PART 74

FCC-ID:

POUMTP40

Limited to 698MHz

PART 74

FCC-ID:

POUMTP40SUSX

RSS-123, RSS-102

IC:

11967A-MTP40SUSX

Limited to 698MHz

Max Power

50mW

100mW

*

1

50mW

100mW

*

2

Country

Europe

Europe

USA

USA, Canada

MTP40S-JP

MTP40S-NZ

Limited to 714 MHz

10mW

MIC marking identifier can be found in the battery compartment.

EN 300 422-1/-2

EN 300 454-1/-2

100mW

Limited to the range

502÷698MHz

Japan

New Zealand

*

1

MTP40S-0W1 / MTP40S-EUX is not an SRD device, thus it requires specific authorization by your local frequency authority!

*

2

in accordance with KDB 447498 D01 General RF Exposure Guidance v05r02.

Before putting the device into operation, please observe the respective country-specific regulations!

20

MTP40S User Manual

MANUFACTURER DECLARATIONS

In compliance with the following requirements

RoHS Directive (2002/95/EC)

WEEE Directive (2002/96/EC)

Please dispose of the diversity transmitter at the end of its operational lifetime by taking it to your local collection point or recycling center for such equipment

Battery Directive (2006/66/EC)

The supplier batteries or rechargeable batteries can be recycled. Please dispose of them as special waste or return them to your specialist dealer. In order to protect the environment, only dispose of exhausted batteries.

FCC Conformity

The Wisycom microphone pocket transmitter model MTP40S complies with the following requirements:

- FCC (Federal Communications Commission) Part 74

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operations.

Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC ID can be found inside the battery compartment.

FCC-ID: POUMTP40

MTP40S US option

FCC-ID: POUMTP40SUSX

MTP40S USX option

21

MTP40S User Manual

Industry Canada Conformity (MTP40S USX)

EN

This device complies with Industry Canada RSS-123. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

FR

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio RSS-

123. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

ITALY ONLY

Obblighi di informazione agli utilizzatori

ai sensi dell’art. 13 del Decreto Legislativo 25 luglio 2005, n. 151 “Attuazione delle Direttive 2002/95/CE,

2002/96/CE e 2003/108/CE, relative alla riduzione dell’uso di sostanze pericolose nelle apparecchiature elettriche ed elettroniche, nonché allo smaltimento dei rifiuti”

Smaltimento di apparecchiature elettriche ed elettroniche di tipo professionale

Il simbolo del cassonetto barrato riportato sull’apparecchiatura o sulla sua confezione indica che il prodotto alla fine della propria vita utile deve essere raccolto separatamente dagli altri rifiuti.

La raccolta differenziata della presente apparecchiatura giunta a fine vita è organizzata e gestita dal produttore. L’utente che vorrà disfarsi della presente apparecchiatura dovrà quindi contattare il produttore e seguire il sistema che questo ha adottato per consentire la raccolta separata dell’apparecchiatura giunta a fine vita.

L’adeguata raccolta differenziata per l’avvio successivo dell’apparecchiatura dismessa al riciclaggio, al trattamento e allo smaltimento ambientale compatibile contribuisce ad evitare possibili effetti negativi sull’ambiente e sulla salute e favorisce il reimpiego e/o riciclo dei materiali di cui è composta l’apparecchiatura.

Lo smaltimento abusivo del prodotto da parte del detentore comporta l’applicazione delle sanzioni amministrative previste dalla normativa vigente.

Smaltimento batterie usate

Questo prodotto può contenere batterie. Questo simbolo apposto sulle batterie significa che non possono essere smaltite insieme a normali rifiuti domestici, bensì devono essere depositate negli appositi punti di raccolta delle batterie.

Iscrizione al Registro A.E.E. n. IT09100000006319

.

22

DECLARATION OF CONFORMITY

MTP40S User Manual

23

MTP40S User Manual

Via Spin 156

I-36060 Romano d’Ezzelino

Italy

Tel. +39 -0424 -382605

Fax +39 - 0424 - 382733 www.wisycom.com

e-mail: [email protected]

24

advertisement

Related manuals