Waterstone 3600-18-3-SS Hunley 1.75 gpm 4-Hole Kitchen Sink Faucet Installation manual

CONTEMPORARY KITCHEN AND

PREP FAUCET INSTALLATION

INSTRUCTIONS

Kitchen Model #s:

3600-12

3600-18

3800

3825

Prep Model #s:

3500

3900

3925

3600-12 3600-18 3800 3825

3500 3900 3925

BEFORE YOU BEGIN YOUR INSTALLATION:

1 2 3 4

Turn off water supply.

Observe all local plumbing codes.

Inspect plumbing for signs of damage. Replace as necessary.

REQUIRED TOOLS:

Adjustable Wrench

HANDLE POSITION

Waterstone faucets are designed to be installed in 3 different faucet positions. Choose to have the handle on left, front or right. Your faucet is factory configured for the most common positions - a front and right side installation. To reverse this and have the handle positioned on the left, connect the hose for cold water to the hot supply and the hose for hot water to the cold supply. This will maintain the relationship of pulling the handle for hot water or pushing for cold water.

FAUCET INSTALLATION

1.

2.

Phillips Screwdriver

3.

HANDLE ON LEFT

C

COUNTER

OR SINK

HANDLE IN FRONT

4.

DO NOT use petroleum based products on this faucet.

Channel Locks

HANDLE ON RIGHT

F

E

D

B

A

Remove clamp nut (A) and washer (B) from threaded shroud (C).

Fit flexible hoses (D) and rigid sidespray tube (E) through hole on counter or sink. (No plumbers putty is required. O-ring seals base).

Slide washer and thread the clamp nut onto threaded shroud.

Tighten nut snug to underside of sink or counter.

Turn faucet to the desired handle position. Securely tighten clamp screws (F).

A B C D E F

G

A

H C

C D

B

F

E

HOW TO ADJUST HANDLE POSITION AND HANDLE TENSION

FIG.1

ORIGINAL FACTORY POSITION

MAY HIT BACKSPLASH

NEW ADJUSTED POSITION

CLEARS BACKSPLASH

On some kitchen countertops, the handle may hit the backsplash when the faucet handle is positioned to the left or right (Fig. 1). Waterstone gives you the option of adjusting the handle 22.5 degrees to avoid hitting backsplash.

Unscrew and remove metal cap (A) and Hot and Cold Indicator Ring (B). Unscrew and remove holding screw (C) and washer (D). Hold handle (E) in a vertical position. Wiggle and pull straight off faucet. Rotate handle 22 degrees away from backsplash then slide handle back onto valve stem (F). Insert holding screw with washer and tighten. Slide

Hot and Cold Indicator Ring onto handle and thread metal cap back into place. To adjust handle tension, turn ring (G) clockwise to increase or counterclockwise to decrease.

G

A B C D E F

CONNECTING SUPPLY HOSES

Before connecting supply hoses, flush supply stops to clear any debris. Place

HANDLE ON LEFT HANDLE IN FRONT a bucket underneath stops and run water for 5 to 10 seconds. Turn water off. Carefully position hot and cold supplies so they will not interfere with other hoses. Connect supply hoses (A) to supply stops (B). DO NOT use teflon tape or plumbers putty. Turn water back on and check for leaks.

B

OPTIONAL HOT COLD INDICATOR RING

To reverse, or remove Hot and Cold Indicator

F

Ring, unscrew the metal cap, remove ring and metal cap back on.

H C flip. Slide ring back onto handle and screw

C D

E

RED FOR HOT

BLUE FOR COLD

CONNECTING SIDE SPRAY (OPTIONAL)

1.

2.

A

COUNTER

OR SINK

3.

4.

B

C

Insert side spray base (A) into hole of your sink or counter. (No plumbers putty is required) . Slide brass spacer (B) onto shroud.

Screw on attaching nut (C) and securely tighten.

D

Slide sidespray hose (D) through side spray base.

E

F

Turn off water supply. On the faucet, remove cap (E) from end of sidespray tube (F).

Connect and tighten sidespray hose to sidespray tube.

ORIGINAL FACTORY POSITION

MAY HIT BACKSPLASH

NEW ADJUSTED POSITION

CLEARS BACKSPLASH

HANDLE ON LEFT HANDLE IN FRONT HANDLE ON RIGHT

1.

2.

B

C

3.

4.

A

CLEANING AERATOR AND DEBRIS SCREEN

1.

2.

B

3.

C

4.

5.

5.

A

Depending on quality of your household water, the aerator and debris screen may become clogged. We recommend cleaning one week after installation, then a minimum of once of year thereafter. To remove the debris, follow the steps below.

1. Gently unscrew and remove spout tip (A) by hand.

2. Remove O-ring (B). To remove aerator (C), push with finger from bottom.

3. Thoroughly rinse aerator with water until all debris is removed.

4. Place aerator, then O-ring back into spout tip.

5. Gently screw spout tip, by hand, snuggly back onto spout.

INSTALL SOAP/LOTION DISPENSER (OPTIONAL)

1.

2.

A

B

Pull and remove spout

(A) from dispenser body

(B). Remove clamp nut

(C) and brass spacer (D) from threaded shroud.

COUNTER

OR SINK

1-3/8”

HOLE

4.

C

G

D

3.

E

5.

Fit dispenser body through 1-3/8” hole on counter or sink. (No plumbers putty is required) . Slide brass spacer onto shroud.

Screw clamp nut and tighten snug.

Insert open end of red tubing down through dispenser base and into plastic bottle.

Fill plastic bottle with soap or lotion. Thread bottle (E) into bottom of dispenser shroud.

6.

Push down on spout to secure over white

O-rings.

F

Slide red tubing (F) into tube fitting (G) at bottom of spout.

Pump spout a few times to get soap or lotion flowing.

INSTALL AIR SWITCH (OPTIONAL)

1.

2.

A

EXPOSE

THREADS

Before inserting air switch into hole, loosen switch base (A) until threads are exposed.

Slide clear tubing

(B) into tube fitting (C) at bottom of air switch shroud.

B

C

3.

1-1/2”

HOLE

4.

COUNTER

OR SINK

D

Fit air switch and tubing through

1-1/2” hole on counter or sink.

(No plumbers putty is required.

O-ring seals base) .

Slide washer up then screw the clamp nut onto threaded shroud.

Hand tighten nut to underside of sink or counter until snug.

CONTINUED ON NEXT PAGE

CONTINUED FROM PREVIOUS PAGE

5.

6.

7.

8.

GARBAGE DISPOSAL

E

E

Tighten clamp screws (E) securely with screwdriver.

Hand tighten switch base back down to cover threads.

INSTALL SINGLE PORT AIR GAP (OPTIONAL)

1.

2.

A

Slide other end of tubing (F) into tube fitting at bottom of control box (G).

F

G

E

D

3.

Plug control box into undersink electrical outlet. Plug garbage disposal into either dual outlet.

1-1/2”

HOLE

Twist and pull air gap cover (A) off of upper cap nut (B). Unscrew and remove cap nut from piping (C).

B

C

Unscrew and remove top clamp nut (D) from both threadings on piping. Slide gasket (E) off piping and remove.

From underneath counter top, fit air gap piping upward through 1-1/2” hole.

4.

Slide gasket down and screw top clamp nut back onto piping. Adjust the two clamp nuts to fit countertop thickness.

(No plumbers putty is required) .

5.

F

6.

Screw cap nut back onto top of piping until snug. Slide air gap over cap nut and top clamp nut. Be sure to have overflow holes (F) facing sink.

Slide small intake hose

(G) over small connector.

Slide larger drainage hose

(H) over large connector.

Tighten hose clamps.

Turn on water supply and check for leaks.

H

G

INSTALL DUAL PORT AIR GAP (OPTIONAL)

1.

2.

D

A

E

3.

C

B

1-1/2”

HOLE

4.

5.

Pull air gap (A) off of upper cap nut (B). Unscrew and remove cap nut from piping (C).

F

Unscrew and remove top clamp nut (D) from both threadings on piping. Slide gasket (E) off piping and remove.

6.

From underneath counter top, fit air gap piping upward through 1-1/2” hole.

Slide gasket down and screw top clamp nut back onto piping.

Adjust the two clamp nuts to fit countertop thickness. (No plumbers putty is required) .

Slide small intake hose (G) over small connector.

Slide larger drainage hose (H) over large connector. Tighten hose clamps.

Screw cap nut back onto top of piping until snug.

Slide air gap over cap nut and top clamp nut.

Be sure to have overflow holes (F) facing sink.

J

H

G

M

L

K

Third intake hole (J) has 3 options. Use hose connector (K) for additional dishwasher, use filtration hose connector (L) for reverse osmosis unit, or use solid cap (M) to plug third hole.

41180 Raintree Court • Murrieta, CA 92562 • 1-888-304-0660 • 951-304-0520 •www.waterstoneco.com

VEN-038-CKP Rev. A