Model:
390
SERIES
INSTALLATION INSTRUCTIONS
E.L. Mustee & Sons, Inc.
5431 West 164th St.
Brook Park, OH 44142
Phone: 216.267.3100
Fax: 216.267.9997
Email: [email protected]
Web: www.mustee.com
CareGiver
®
Fold-Down Padded Seats
READ ALL INSTRUCTIONS CAREFULLY AND INSPECT PRODUCT FOR DAMAGE BEFORE STARTING YOUR INSTALLATION.
Left-hand seat — wall mount
390.402 style
Right-hand seat — wall mount
390.401 style
Rectangular seat — wall mount
390.409 or 390.413 style
INCLUDED IN CARTON:
One (1) seat assembly with two wall brackets (attached)
One (1) middle support “slide” bracket
One (1) template for mounting
TOOLS AND MATERIALS FOR INSTALLATION:
Drill – electric or cordless
3 /
16
" and 1
24" level
/
4
" drill bits
Screwdriver
Tape measure, pencil
Silicone caulk
Eight (8) 1 /
4
" x 3" stainless steel lag screws
Mounting hardware not supplied due to variations in wall backing. Use appropriate fasteners as recommended by a qualified contractor. Fasteners listed are only suggestions and should be chosen to best fit the needs of your specific application.
Model 390.409 Rectangular Seat
(Shown in down/useable position)
IMPORTANT SAFETY CAUTIONS:
■ ■
Due to variances in local building codes and requirements, the installation instructions provided here are only suggestions. IT IS STRONGLY ADVISED that you contact a qualified contractor for application specific advice.
■ ■
CareGiver ® Fold-Down Shower Seats are only as strong as the strength and rigidity of the material to which they are mounted.
Support
Arm
■ ■
The seat is intended for sitting purposes only. ONE person at a time. DO NOT attempt to stand, kneel or use the seat for any other purpose other than sitting.
Upper
Mounting
Bracket
■ ■
The seat is designed to withstand 400 lbs. – when properly installed. Improper installation may cause bodily harm.
■ ■
IMMEDIATELY DISCONTINUE use of the seat if visual signs of fatigue or wear become evident. Regular inspections should be made to confirm that the seat is not pulling away from the wall. If the wall brackets start to pull away from the wall IMMEDIATELY discontinue use and call a qualified contractor.
Up/storage position
Guide
Bracket
In installing from new construction, a steel backer plate with the seat bolted to the plate (through the shower wall) using fender washers is the preferred mounting method.
PREPARATION:
Check local code for proper placement of Fold-Down Padded Seats to meet requirement such as ADA or ANSI 117.1
Consumer Safety Requirements.
Before installing the Fold-Down Padded
Seat you will have to prepare the area.
ROUGH-IN INSTALLATION: Determine where the Fold-Down Padded Seat will be mounted and install bracing to the rough-in framing to support the seat through the shower wall. Provide no smaller than a 2" x 6" blocking in the wall for mounting. Measure from the sub-floor up 13 1 /
4
". Center the 2" x 6" horizontally over three wall studs and with the center of the 2" x 6" at the
13 1 /
4
" mark.
Notch wall studs to accommodate the header and attached with no less than
Six (6) – 5 /
16
" x 3" stainless steel lag screws. (as shown in Fig. 1a)
Before finishing the wall, and using the dimensions of your seat, ensure that the two upper mounting brackets and the top two screws of the guide bracket will line up with the 2" x 6" blocking, while the third bottom screw of the guide bracket will line up with the middle and wall stud. (as shown in Fig. 1b)
Finish the stud wall with tile, Mustee fiberglass shower wall kit or other.
PREPARATION: (continued)
EXISTING WALL INSTALLATION: Locate stud behind the existing shower wall to determine where the Fold-Down Padded
Seat can be safely mounted. Both the upper mounting bracket and guide bracket must be in contact with studwall.
Clean that portion of the shower wall where the Fold-Down Seat will be installed.
INSTALLATION
STEP 1:
Locate the desired seat position making sure that the top of the seat is between 17" – 19" from the finished floor. When measuring, the seat must be in the down, usable position. With a 24" level check from side-to-side and frontto-back to ensure that the seat is level. A slight 2° – 3° rise on the seat from the back wall to the front of the seat is recommended.
STEP 2:
Use a pencil and mark the three screw holes from both upper mounting brackets.
Then mark the three holes from the guide bracket. Be careful of its position, the bottom screw of the guide bracket needs to be centered on the middle wall stud with the two top screws fastened to the 2" x 6". (as shown in Fig. 2)
STEP 3:
Remove the seat. In each of your marked locations, drill the tile only. Then drill 3 / seat using 1 /
4
16
1 /
4
" clearance holes through
" pilot holes through the header board and attach the
" x 3" stainless steel lag screws and fender washers. Use a generous amount of silicone caulk to prevent water seepage into the mounting holes.
STEP 4:
Make sure the seat raises and lowers smoothly. If installed correctly, the seat will remain in the “up” position by itself and will take little effort to lower it.
13 1
4
/ "
Wall Studs, Typically 16" on Center
16" 16"
Fig. 1a
9
11
1 to
1
/ "
/ "
1"
3"to 5"
2" x 6"
Blocking
Center at 13 1
(to achieve
17" – 19" seat height)
/
4
"
Fig. 1b
17"to 19"
Top of seat to finished floor
Fig. 2
CARE & CLEANING
To clean, wipe seat down with mild soap and water.
INSTALLATION QUESTIONS
Questions on the installation or missing parts, call 216-267-3100 or e-mail [email protected] for assistance. Hours of operation are Monday to Friday, 8:30 a.m. to 4:30 p.m. E.S.T.
Please have the installation manual available when calling. DO NOT RETURN PRODUCT TO THE PLACE OF PURCHASE.
Preferred by the “Pros”
As a company committed to continuous improvement, the specifications in this installation manual are subject to change without notice.
SI-246 (11-14)
Patented and patents pending. Assembled and Printed in U.S.A.
