- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- Cal Spas
- Special Edition Spa
- Owner's manual
- 60 Pages
Cal Spas Special Edition Spa 2020 Owner’s Manual
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
LTR20201163, Rev. Z3
6/26/20
Table of Contents
Important Safety Instructions . . . . . . . 1
Preparing for Your New Portable Spa . 2
Pre-Delivery Checklist. . . . . . . . . . . . . . . . . . 2
Planning the Best Location . . . . . . . . . . . . . . 2
Preparing a Good Foundation . . . . . . . . . . . . 3
Opening the Front Door Panel for
Electrical Hookup. . . . . . . . . . . . . . . . . . . . . . 3
240 Volt Electrical Installation . . . . . . . . . . . 4
Wiring Requirement . . . . . . . . . . . . . . . . . . . 5
GFCI Wiring Diagram (NEO) for US &
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
120 Volt Electrical Installation . . . . . . . . . . . 7
Testing the 240 Volt GFCI Breaker. . . . . . . . 7
Filling and Powering Up Your Portable Spa 7
Priming the Pump . . . . . . . . . . . . . . . . . . . . 10
Operating Your Spa . . . . . . . . . . . . . . . 11
Primary Navigation & Functions of NEO
One & Two-pump Systems . . . . . . . . . . . . . 11
Jets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
LED Lighting. . . . . . . . . . . . . . . . . . . . . . . . . 23
Diverter Knobs. . . . . . . . . . . . . . . . . . . . . . . 24
Air Venturis . . . . . . . . . . . . . . . . . . . . . . . . . 24
Waterfalls . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Hydro Streamer Waterfall. . . . . . . . . . . . . . 24
Water Clarity . . . . . . . . . . . . . . . . . . . . 25
Water Quality Terms and Definitions . . . . . 25
Water Testing Methods . . . . . . . . . . . . . . . . 26
Adding Chemicals to the Spa Water . . . . . . 27
1. Balancing the Water Chemistry Levels . 27
2. Sanitation and Shock . . . . . . . . . . . . . . . 29
3. Filtration . . . . . . . . . . . . . . . . . . . . . . . . . 30
4. Regularity (Maintenance Schedule). . . . 31
Generic Names for Chemicals . . . . . . . . . . . 31
Common Water Chemistry Questions . . . . 32
Do’s and Don’ts . . . . . . . . . . . . . . . . . . . . . . 33
Bather Load . . . . . . . . . . . . . . . . . . . . . . . . . 34
Ozonator . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Troubleshooting Water Clarity Problems . . 35
Cleaning and Maintenance and Sound
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Removing and Reseating the Pillows . . . . . 36
Jet Removal and Replacement . . . . . . . . . . 36
Draining Your Portable Spa . . . . . . . . . . . . 37
Winterizing (Cold Climate Draining) . . . . . 38
Cleaning and Replacing the Filter. . . . . . . . 38
Spa Cover and Locking System
Installation . . . . . . . . . . . . . . . . . . . . . . . . . 38
Vacation Care. . . . . . . . . . . . . . . . . . . . . . . . 40
Cleaning Your Spa . . . . . . . . . . . . . . . . . . . . 40
Using the Freedom Sound System . . . . . . . 40
Appendix . . . . . . . . . . . . . . . . . . . . . . . 41
Replacement Parts . . . . . . . . . . . . . . . . . . . 41
Basic Troubleshooting. . . . . . . . . . . . . . . . . 47
“Thermal Creep” . . . . . . . . . . . . . . . . . . . . . 49
Limited Warranty. . . . . . . . . . . . . . . . . . . . . 50
Warranty Registration. . . . . . . . . . . . . . . . . 58
Copyright 2020 LMS. All rights reserved. Duplication without written consent is strictly prohibited.
Cal Spas
®
and Freedom Sound System
™
are registered trademarks.
Due to continuous improvement programs, all models, operation, and/or specifications are subject to change without prior notice.
LTR20201163, Rev. Z3
6/26/20
CONTACT INFORMATION
For customer service, please contact your authorized dealer immediately. If you need additional information and/or assistance, contact:
LMS Customer Service Department
1462 East Ninth Street
Pomona, CA 91766.
Toll Free: 1-800-CAL-SPAS
Fax: 1-909-629-3890
Important Safety Instructions
READ AND FOLLOW ALL INSTRUCTIONS.
DANGER -- Risk of accidental drowning:
Do not allow children to be in or around a spa unless a responsible adult supervises them. Keep the spa cover on and locked when not in use. See instructions enclosed with your cover for locking procedures.
DANGER -- Risk of injury:
The suction fittings in this spa are sized to match the specific water flow created by the pump. Should the need arise to replace the suction fittings, or the pump, be sure the flow rates are compatible.
Never operate the spa if the suction fitting or filter baskets are broken or missing. Never replace a suction fitting with one that is rated less than the flow rate marked on the original suction fitting.
DANGER -- Risk of electric shock:
Install the spa at least 5 feet (1.5 meters) from all metal surfaces. As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal surface is permanently bonded by a minimum #8 AWG solid copper conductor to the outside of the spa’s control box.
Do not permit any external electrical appliances, such as lights, telephones, radios, televisions, and etc., within five feet (1.5 meters) of the spa. Never attempt to operate any electrical device from inside the spa.
Replace a damaged power cord immediately.
Do not bury the power cord.
Connect to a grounded, grounding-type receptacle only.
WARNING -- To reduce the risk of injury:
The spa water should never exceed 104˚F (40˚C). Water temperatures between 100˚F (38˚C) and 104˚F (40˚C) are considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.
High water temperatures have a high potential for causing fetal damage during pregnancy. Women who are pregnant, or who think they are pregnant, should always check with their physician prior to spa usage.
The use of alcohol, drugs or medication before or during spa use may lead to unconsciousness, with the possibility of drowning.
Persons suffering from obesity, a medical history of heart disease, low or high blood pressure, circulatory system problems or diabetes should consult a physician before using the spa.
Persons using medications should consult a physician before using the spa since some medications may induce drowsiness while others may affect heart rate, blood pressure and circulation.
HYPERTHERMIA DANGER:
Prolonged exposure to hot air or water can induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level 3˚F to 6˚F above the normal body temperature of 98.6˚F (or 2˚C to 4˚C above 37˚C). While hyperthermia has many health benefits, it is important not to allow your body’s core temperature to rise above 103˚F (39.5˚C).
Symptoms of excessive hyperthermia include dizziness, lethargy, drowsiness and fainting. The effects of excessive hyperthermia may include:
• Failure to perceive heat
• Failure to recognize the need to exit spa or hot tub
• Unawareness of impending hazard
• Fetal damage in pregnant women
• Physical inability to exit the spa
• Unconsciousness
WARNING:
The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia.
WARNING:
People with infectious diseases should not use a spa or hot tub.
WARNING:
To avoid injury, exercise care when entering or exiting the spa or hot tub.
WARNING:
Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness and
2020 Portable Spas - LES
LTR20201163, Rev. Z3 possible drowning.
WARNING:
Do not use a spa or hot tub immediately following strenuous exercise.
WARNING:
Prolonged immersion in a spa or hot tub may be injurious to your health.
CAUTION
: Maintain water chemistry in accordance with manufacturer’s instructions.
www.calspas.com
1
2
Preparing for Your New Portable Spa
Pre-Delivery Checklist
Most cities and counties require permits for exterior construction and electrical circuits. In addition, some communities have codes requiring residential barriers such as fencing and/or self-closing gates on property to prevent unsupervised access to the property by children. Your dealer can provide information on which permits may be required and how to obtain them prior to the delivery of your spa.
Before Delivery
Plan your delivery route
Choose a suitable location for the spa
Lay a 5 - 8 cm concrete slab
Install dedicated electrical supply
After Delivery
Place spa on slab
Connect electrical components
Planning the Best Location
Safety First
Do not place your spa within 10 feet (3 m) of overhead power lines.
Provide a View with Your Spa
Consider How You Will Use Your Spa
How you intend to use your spa will help you determine where you should position it. For example, will you use your spa for recreational or therapeutic purposes? If your spa is mainly used for family recreation, be sure to leave plenty of room around it for activity. If you will use it for relaxation and therapy, you will probably want to create a specific mood around it.
Think about the direction you will be facing when sitting in your spa. Do you have a special landscaped area in your yard that you find enjoyable? Perhaps there is an area that catches a soothing breeze during the day or a lovely sunset in the evening.
Keep Your Spa Clean
In planning your spa’s location, consider a location where the path to and from the house can be kept clean and free of debris.
Prevent dirt and contaminants from being tracked into your spa by placing a foot mat at the spa’s entrance where the bathers can clean their feet before entering your spa.
Plan for Your Environment
If you live in a region where it snows in the winter or rains frequently, place the spa near a house entry. By doing this, you will have a place to change clothes and not be uncomfortable.
Consider Your Privacy
In a cold-weather climate, bare trees won’t provide much privacy. Think of your spa’s surroundings during all seasons to determine your best privacy options. Consider the view of your neighbors as well when you plan the location of your spa.
Allow for Service Access
Make sure the spa is positioned so that access to the equipment compartment and all side panels will not be blocked.
Many people choose to install a decorative structure around their spa. If you are installing your spa with any type of structure on the outside, such as a gazebo, remember to allow access for service. It is always best to design special installations so that the spa can still be moved, or lifted off the ground.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Preparing a Good Foundation
Your spa needs a solid and level foundation. The area that it sits on must be able to support the weight of the spa, with water and the occupants who use it. If the foundation is inadequate, it may shift or settle after the spa is in place, causing stress that could DAMAGE YOUR
SPA SHELL AND FINISH.
Damage caused by inadequate or improper foundation support is not covered by the warranty. It is the responsibility of the spa owner to provide a proper foundation for the spa.
Place the spa on an elevated 3 to 4” / 30 cm concrete slab.
Pavers, gravel, brick, sand, timbers or dirt foundations are
not
adequate to support the spa.
We strongly recommend that a qualified, licensed contractor prepare the foundation for your spa.
If you are installing the spa indoors, pay close attention to the flooring beneath it. Choose flooring that will not be damaged or stained.
If you are installing your spa on an elevated wood deck or other structure, it is highly recommended that you consult a structural engineer or contractor to ensure the structure will support the weight of 150 pounds per square foot (732 kg / m2).
To properly identify the weight of your new spa when full, remember water weighs 8.33 lbs. per gallon, or 1 kg per liter. For example, an average 8’ spa holds approximately
500 gallons, or 1892 liters, of water. Using this formula, you will find that the weight of the water alone is 4,165 lbs, or
1892 kg. Combined with the dry weight of the spa you will note that this spa will weigh approximately 5,000 lbs, or
2267 kg, when full of water.
3
Opening the Front Door Panel for Electrical Hookup
The following electrical connections must be performed by a licensed electrical contractor.
Unscrew and remove the two corner panels on each side of the spa’s front door.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
4
Reach in and pull the drain assembly through by a few inches. Carefully unscrew the black outer drain knob and then unscrew and remove the front door panel.
Pictured to the right is the inside of the spa behind the front door. The electrician now has access to connect the spa for power. While the front door is off, refer to page 7 for instructions on ensuring the plumbing fittings are secure
(but do not be tempted to over-torque or over-tighten these fittings).
Pull the drain pipe through the front door panel, reattach the black outer drain knob and pull the drain assembly back inside so that the knob is flush with the panel again. Reattach and screw panels back in. (Front door first, then corner panels)
240 Volt Electrical Installation
All 240V spas must be permanently connected (hard wired) to the power supply. See the GFCI and wiring requirements on page 6.
Failure to comply with state and local codes may result in fire or personal injury and will be the sole responsibility of the spa owner.
These instructions describe the only acceptable electrical wiring procedure. Spas wired in any other way will void your warranty and may result in serious injury.
When installed in the United States, the electrical wiring of this spa must meet the requirements of NEC 70 and any applicable local, state, and federal codes.
The electrical circuit must be installed by an electrical contractor and approved by a local building or electrical inspector.
www.calspas.com
The power supplied to the spa must be on a dedicated
GFCI protected circuit as required by NEC 70 with no other appliances or lights sharing the power.
Use copper wire with THHN insulation. Do not use aluminum wire.
Use the table below to determine your GFCI and wiring requirements.
Wires that run over 100 feet must increase wire gauge to the next lower number. For example: A normal 50 amp
GFCI with four #6 AWG copper wires that run over 100 feet would require you to go to four #4 AWG copper wires.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Wiring Requirement
Control System
NEO 1500/ \NEO 2100
GFCI Required
One 50 amp GFCI
Wires Required
Four #6 AWG copper wires
5
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
6
GFCI Wiring Diagram (NEO) for US & Canada
Control System
NEO 1500
GFCI Required
One 40 amp GFCI
Wires Required
Four #8 AWG copper wires
www.calspas.com
See the Cal Spas Pre-Delivery Guide for more information on spa placement for service access and electrical service.
www.calspas.com/manuals
2020 Portable Spas - LES
LTR20201163, Rev. Z3
120 Volt Electrical Installation
Always follow applicable local, state and federal codes and guidelines.
Use only a dedicated electrical line with a 15 amp breaker.
Cord-and-plug connections may not use a cord longer than 15 feet (4.6 m) and must be plugged into a dedicated 15 amp GFCI connection (NEC 680.42(A)
(2)). Do not use extension cords!
Always use a weatherproof-covered receptacle.
Receptacle shall be located not less than 5 feet (1.5 m) from and not exceeding 10 feet (3.0 m) from the inside wall of the spa. (NEC 680.43(A))
Do not bury the power cord. If your cord becomes damaged, replace it before next usage.
All 120V spas must have a GFCI. This can be either a
15 amp GFCI receptacle or a 15 amp GFCI cord and plug kit as shown (CKIT110 - P/N ELE09700086).
Testing the GFCI plug
Test the GFCI plug prior to first use and periodically when the spa is powered.
1. Plug in the GFCI into the power outlet. The indicator should turn on.
2. Press the TEST button.
The GFCI will trip, the indicator will turn off, and the spa will stop operating.
3. Press the RESET button. The GFCI will reset, the indicator will turn on again, and the spa will turn back on.
The spa is now safe to use.
If the GFCI trips while the spa is in use, press the RESET button.
If the GFCI does not reset, unplug the spa and call your local Cal
Spas dealer for service. DO NOT USE THE SPA!
Testing the 240 Volt GFCI Breaker
Test the GFCI breaker prior to first use and periodically when the spa is powered. To test the GFCI breaker follow these instructions (spa should be operating):
1. Press the TEST button on the GFCI. The GFCI will trip and the spa will shut off.
2. Reset the GFCI breaker by switching the breaker to the full OFF position, wait a moment, then turn the breaker back on. The spa should have power again.
Filling and Powering Up Your Portable Spa
1. Inspect the spa equipment.
Inspect all plumbing connections in the equipment area of your spa.
• Make sure unions in the equipment pack are tight. (Be careful not to over-tighten the plumbing fittings.)
• If your spa has gate valves, make sure they are all in the UP or OPEN position.
• Make sure the drain valve is closed and capped. (See page 37 for a description of drain valves.)
Never run the spa with the gate valves closed or without water circulating for long periods of time.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
7
8
2. Remove the cartridge from filter canister.
If you have a skimmer like this:
Grip the filter by the handle and unscrew it from the canister. Never try to pull the filter cartridge while the spa is running in low or high speed (i.e., any speed).
If you have a skimmer like this:
Remove the black skimmer cap and barrel, grip the filter by the handle and unscrew it from the canister.
If you have a skimmer like this:
Rotate and remove the black locking ring. Remove the black skimmer cap and barrel, grip the filter by the handle and unscrew it from the canister.
Replace and lock the locking ring and slide the skimmer cap and barrel back in the canister.
Note:
The skimmer cap and barrel were locked in place at the factory to prevent damage during shipment. It must be unlocked and replaced in the filter canister so that it can float when the spa is filled. If you do not remove the cap and barrel, your spa’s filtration system will not perform as it was designed to.
Teleweir filter skimmer
• 50 square feet filtration
• Spoked cap
Teleweir Mega filter skimmer
• 75 square feet filtration
• Smooth cap
After you remove the filter, remove the plastic wrapper and soak it in water for 30 minutes before you replace it. A dry filter can allow air into the filtration system which can cause the pump to fail to prime.
3. Fill the spa.
Place a garden hose in the filter canister and fill your spa
.
Always fill the spa through the filter canister.
Failure to do so may cause air to be trapped in the filtration system and prevent the pumps from operating properly.
Fill the spa until water level is about six inches from the top.
If the water level is too low or too high, your spa will not operate properly.
Never fill your spa with soft water.
Soft water
makes it impossible to maintain the proper water chemistry and may cause the water to foam, which will ultimately harm the finish of the spa and void your warranty. You may fill your spa with
well water www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
provided the following conditions are met:
1) Purchase and use a pre-filter to run the well water through on the fillup. The pre-filter will be placed before the spa filter in the fill-up flow of water. 2) Have a Total Dissolved Solids (TDS) and metals test performed by a qualified person after the fill-up process but before any spa use.
4. Turn on power to the spa.
When the spa is filled to the correct level, turn on the power at the GFCI breaker. (Ensure that the 120V spas are connected to the proper electrical outlet.)
9
5. Prime the pump. (NEO system)
The system will enter the priming mode.
Priming Mode
will display on the control panel. In Priming Mode, all devices such as jets and lights are operable. Jets can be turned on and off to help prime the pump. The system will exit Priming Mode and go to the Main display when the RETURN button is pressed, or after four minutes of inactivity.
6. Install the filter into the filter canister.
Make sure the filter has soaked at least 30 minutes before you install it. Insert the filter all the way and screw it in. Do not over-torque the cartridge during installation, just hand tighten gently.
7. Adjust water chemistry.
Test and adjust the water chemistry. See the section on page 25 for instructions on keeping your water clear.
8. Let the spa heat up.
When the spa has finished priming, the heater will activate. Put the cover on and let the spa heat to the set temperature.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
10
Priming the Pump
New spa owners often have difficulty the first time they start their spa and the pump fails to prime. This can be frustrating, but these simple instructions can help you.
Sometimes air can become trapped in the pump while filling the spa. You will know this has happened when after you have filled and started the spa, the pump does not seem to function. You will hear the pump operating, but no water will be moving.
There are two methods of priming the pump.
The first method will remove small air bubbles trapped in the pump.
1. Turn the spa on and wait for PR (Priming Mode) to appear on the topside display.
2. Press the JETS 1 button to turn on the pump and let it run for 10 seconds. The pump should be running in low speed.
3. Press the JETS 1 buttons again and let the pump run in high speed for 10 seconds.
4. Press the JETS 1 button again to turn off the pump. The pump should be left in the off position for 10 to 15 seconds.
5. Repeat steps 1 through 4 until water is flowing through all the jets and all air is removed from the plumbing.
The second method will remove a large air lock within the pump.
1. Using a Phillips screwdriver, remove the front panel from the spa and locate the pump.
2. While the spa is operating, turn the bleeder valve counter clockwise with a small pair of pliers or a flat head screwdriver until the air has been released from the pump.
3. If this is unsuccessful, loosen the white union nut on side of the pump with channel locks. When air is bled out, tighten the nut and set the pump on high speed.
The pump will not work properly while air is trapped in it.
Continuing to operate the pump in this way will cause damage.
Whenever you fill your spa, fill it through the filter canister and make sure all jets are open.
Note: If you press the
Temp
button any time during Priming Mode, it will exit that mode and begin Standard Mode.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Operating Your Spa
Primary Navigation & Functions of NEO One & Two-pump Systems
1100 Wave Panel and 1100 Oval Panel
11
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
12
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
13
14
Settings Screens
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Error Screens
15
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
16
Adjusting Date-Time and Filtration Settings
Shown below is the default topside screen. (Your temperature setting may vary according to your preferences.) In order to access and change the internal clock of your spa, first press MENU.
That action will take you to this screen
Use the COOL (Down arrow) to highlight the Date-Time option (which is now highlighted in white).
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Press the MENU button to select the option.
Press the UP-DOWN buttons to increase or decrease the value of each highlighted field.
Press the MENU button to advance to the next field you wish to change.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
17
18
Press RETURN when you have finished setting date and time to save your chosen settings.
Once the screen has reverted back to temperature, you can now adjust Filter Cycles.
NOTE: You do not necessarily have to adjust the Filter Cycles because the default factory settings give you two Filter Cycles per day automatically.
In any case, to access the Filter Cycles, press the MENU button.
This time select Filter Cycles. (Press the MENU button to access the sub-menus.)
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Filter Cycles 1 and 2 are the factory-programmed defaults. These may be satisfactory for your needs, but can be customized if you wish.
If you leave the Filter Cycles option untouched, you will still have Filter Cycles 1 and 2 working for you every day.
Filter Cycles 3 and 4 can also be employed in addition to Filter Cycles 1 and 2 and these Cycles allow full customization as well.
19
Filter Cycles 1, 2, 3 and 4 can all be adjusted in 15 minute increments. Use the MENU button to move from field to field, use the UP and DOWN arrows to make adjustments and then press RETURN once you’re satisfied with your selections for all Cycles. Please note that the system will not allow you to set overlapping or contradictory Cycles.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
20
Operating the NEO Wi-Fi App
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
21
22
Connecting to a Device or Network
1
Direct connection
Range: About 20 feet
Range limit: Limited to the range of the wi-fi module
HOW TO CONNECT TO IT:
Install the app on your phone or device -- see the following section “Installing the app”.
2
Through home network with no internet access
Allows one local connection at a time
Range: About 50 feet
Range limit: Limited to the range of your home router’s signal
HOW TO CONNECT TO IT:
1. Install the app on your phone or device.
2. Exit the app and go to wi-fi settings on your phone or device.
3. Select and enable your local router.
4. Start the app. After you connect, select Settings on the home screen.
5. On the Settings screen, select Advanced, then on the Advanced screen, select Wi-fi Settings.
6. On the Wi-fi screen, select WPA. Then select the name of your home router from the drop-down menu.
7. Enter the SSID and Key for your router, the tap Save and select OK twice.
8. Close the app and re-start it to connect to your home network.
3
Through a network with internet access, using
Cloud connection or other hotspot connection
Allows unlimited simultaneous connections
Range: Worldwide
Range limit: Limited to 3G / 4G / hotspot availability
HOW TO CONNECT TO IT:
Follow connection instructions from section (2) above. The Cloud icon appears automatically when network connection is made. You can then connect to the spa’s wi-fi module.
Internet
Local hotspot
3G or 4G
Wi-fi
Your spa
Wi-fi signal
Phone or other device
Your home network router
Internet cloud connection
Local wi-fi connection
Jets
Almost all of the jets in your spa are adjustable. Rotating the face of an adjustable jet to the left (counterclockwise) will decrease the amount of water flow through the jet. Rotating the face of an adjustable jet to the right
(clockwise) will increase the amount of water flow through the jet. (See example shown here.)
Neck jets adjust in the opposite directions (counterclockwise to increase, clockwise to decrease).
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
LED Lighting
Press the LIGHT button on the topside control panel to turn the spa light on. If your spa has perimeter LED lights, they will also light up at the same time as the spa light.
The LEDs operate in three modes:
1. Cycle:
When you continually press the LIGHT button, the LEDs will cycle through the three main LED colors
(Red, Green, and Blue) or combinations of the three that produce the following colors: light green, purple, light blue, yellow, etc.
Each time you press the button, you immediately advance to the next color in sequence or eventually a different light pattern.
2. Flashing:
When you are cycling through all the colors, the next time you push the LIGHT button, the LED lights may start flashing. This is another normal operational pattern option.
3. Fading cycle:
The next phase of operation when you push the LIGHT button is a slow and/or fast fade random transition from one color to the next.
• If a spa is equipped with more than 100 points of light, the Slow Fading Cycle will flicker during a color change.
• Every air valve and water valve is equipped with 4 LED points.
• Every jet is equipped with 2 LED points.
• Perimeter LEDs take 9 points of light.
• The waterfall takes 4 points of light.
Spas with exterior corner LED lighting generally work in the same mode as described above. The variations in color and patterns provide you with multiple options to suit almost any lighting preference.
23
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
24
Diverter Knobs
Diverter knobs are 1” and 2” knobs located around the top of your spa. They allow you to divert water through jets from one side of the spa to the other, or in most cases from floor jets to wall jets. This is accomplished by rotating the diverter knob to the left (counterclockwise), decreasing the amount of water flow through a section of jets. To increase the amount of water flow through the other section of jets, rotate the handle to the right (clockwise).
Air Venturis
Air venturis are the 1” knobs located around the top of your spa. Each one will let you add a mixture of air with the jet pressure. This is accomplished by rotating the air venturi knob to the left (counterclockwise) to increase the amount of airflow through the jets. To decrease the amount of airflow through the jets, rotate the handle to the right (clockwise).
Waterfalls
Some spa series include optional waterfalls. When the booster pump is on, rotate the dial on top (for the cascade waterfall) or turn the knob (for the hydro streamer -- see below).
Hydro Streamer Waterfall
Your spa may include two to eight streamer waterfalls. When the booster pump is on, turn the
1” diverter knob to adjust the rate of flow to the waterfall jets.
The waterfall jet faces are not adjustable. Do not turn the jet faces because you may accidentally remove them.
Always shut off water to the hydro streamer jets before you place the cover on the spa. Water from the hydro streamer jets sprays in an arc that is higher than the top surface of the spa. When water from the hydro streamer sprays the bottom of the cover, it will collect and run to the edge of the spa and drip over the top.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Water Clarity
This section is intended for new spa owners with no experience with water chemistry. Everyone’s experience with maintaining water quality is different, but there are some general concepts you need to know.
Water maintenance is not difficult, although it requires regular attention. The most important thing to understand about taking care of your spa water is that preventive action is much easier than correcting water quality issues.
Before you begin, we recommend you become familiar with some water quality terms and their definitions (see next page).
Whether you’re filling your spa for the first time (see page
7) or refilling it after draining it for regular maintenance
(see page 37), start and maintain your spa water by following the plan we describe in this section.
1
Chemical Balance
See page 27 to learn how to balance your spa water.
You will need to test and adjust the chemical balance of your spa water. Although this is not difficult, it needs to be done regularly.
You need to test the level of calcium hardness, total alkalinity, and pH.
2
total dissolved solids and phosphates.
Sanitation and Shock
See page 29 to learn how to use sanitizer and shock.
Sanitizers kill bacteria and viruses and keep the water clean. A low sanitizer level will allow microbes to grow quickly in the spa water. We recommend using either chlorine or bromine as your sanitizer.
Spa owners with a bromine generator also need to check
You also need to add shock to the water to stimulate the chemical sanitizer. How much you use and how often depend on
3
frequency and intensity of use.
Spa owners with an ozonator also need to add sanitizer, although their requirements are different.
4
and pump to work harder than they need to, possibly causing them to fail.
The spa’s heating system will only function with the proper amount of water flow through the system.
Filtration
See page 30 for filter cleaning instructions.
Cleaning your filter regularly is the easiest and most effective single thing you can do to keep your water clear.
A clogged or dirty filter will cause the heater
Regularity
See page 31 for the schedule of recommended maintenance.
Clear water requires regular maintenance. Establish a routine based on a regular schedule for your spa water maintenance.
Maintaining your water quality helps the enjoyment of your spa and extends your spa’s life by preventing damage from neglect and chemical abuse.
Water Quality Terms and Definitions
The following chemical terms are used in this section. Understanding their meaning will help you to better understand clear water maintenance. Words in bold type are defined in this table.
Bromine /
Bromamines
Chlorine /
Chloramines
Bromine is an efficient sanitizer chemical for spas. When used as a
sanitizer
, bromine forms compounds called bromamines. Bromine can be added to the spa or automatically generated. See page 29 for discussion on
sanitizers
.
Bromamines are compounds formed when bromine combines with nitrogen from body oils, perspiration, etc.
Unlike chloramines, bromamines have no pungent odor and are effective
sanitizers
.
Chlorine is an efficient sanitizing chemical for spas. We recommend using sodium dichlor-type granulated chlorine because it is totally soluble and nearly
pH
neutral. When used as a
sanitizer
, chlorine forms compounds called chloramines. See page 29 for discussion on
sanitizers
.
Chloramines are compounds formed when chlorine combines with nitrogen from body oils, perspiration, etc.
Chloramines can cause eye irritation as well as having a strong odor. Unlike
bromamines
, chloramines are weaker, slower
sanitizers
. To remove chloramines, see the description of
shock
below.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
25
26
Calcium Hardness
Corrosion
Dichlor
Monopersulphate or MPS
Oxidizer
Ozone pH ppm
Sanitizer
Scale
Shock
Total Alkalinity
Trichlor
Abbreviated as CH. Calcium hardness is a measure of the total amount of dissolved calcium in the water.
Calcium helps control the
corrosive
nature of the spa’s water and is why soft water is not recommended. The low CH level can cause
corrosion
to the equipment and can cause staining of the spa shell. See page 42 for testing for and balancing calcium hardness.
The gradual wearing away of metal spa parts, usually caused by chemical action. Generally, corrosion is caused by low
pH
or by water with levels of
TA
,
CH
,
pH
or sanitizer which are outside the recommended ranges.
Also called sodium dichlor. It is a type of chlorine and is frequently used when
shocking the water
. An effective
chlorine
-based powdered
oxidizer
and
sanitizer
. Dichlor works by oxidizing waste product in the water such as
bromamines
and
chloramines
and causing them to burn off.
Frequently used when
shocking the water
. An effective non-chlorine-based powdered
oxidizer
that works well with both
chlorine
and
bromine
. It works by oxidizing waste product in the water such as
bromamines
and
chloramines
and causing them to burn off.
Shocking the water
with an oxidizing chemical prevents the buildup of contaminants, maximizes
sanitizer
efficiency, minimizes combined
chlorine
and improves water clarity.
Ozone is a powerful oxidizing agent which is produced in nature and artificially. Ozone forms no by-products of
chloramines
(ozone actually oxidizes chloramines) and will not alter the water’s
pH
.
The pH level is the measure of the balance between acidity and alkalinity. Low pH causes the water to be too acid, which will cause
corrosion
, whereas high pH causes the water to be too alkaline, which will cause
scaling
. See page 28 for testing for and balancing pH.
The abbreviation of “parts per million”, the standard measurement of chemical concentration in water. Identical to mg/l (milligrams per liter).
Sanitizer is a chemical added to the water to kill bacteria and viruses and keep the water clean. The two sanitizers we recommend are
chlorine
and
bromine
. See page 29 for discussion of sanitation.
Rough calcium-bearing deposits that can coat spa surfaces, heaters, plumbing lines and clog filters. Generally, scaling is caused by mineral content combined with high
pH
. Additionally, scale forms more readily at higher water temperatures.
Also called shocking the water, shock treatment, or superchlorination. Shocking the water is adding significant doses of
dichlor
or
MPS
to
oxidize
non-filterable organic waste and to remove
chloramines
and
bromamines.
Shock treatment breaks down organic waste contaminants which cause odor and cloudy water. See page 30 for discussion of shocking the water.
Abbreviated as TA. Total alkalinity is the measure of the total levels of carbonates, bicarbonates, hydroxides, and other alkaline substances in the water. TA is important for
pH
control. If the TA is too low, the
pH
will fluctuate out of control, and if it is too high, the
pH
becomes difficult to stabilize. See page 27 for testing for and balancing total alkalinity.
Used as a pool
sanitizer
. NEVER use trichlor in a spa. Trichlor is extremely acidic and will lower the
pH
, causing corrosion to equipment. Using trichlor will void your warranty.
Water Testing Methods
There are two testing methods to choose from:
Test strips are a convenient testing method commonly used by spa owners.
The reagent test kit is a method which provides a high level of accuracy but is more expensive and more difficult to use.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Adding Chemicals to the Spa Water
IMPORTANT: All spa water chemicals, including MPS (shock), chlorine, granulated pH increaser or decreaser, granulated total alkalinity increaser, calcium hardness increaser, liquid stain and scale inhibitor, and liquid de-foamer must always be added directly into or in front of the filter compartment while a jet pump is running, and it must run for a minimum of ten minutes.
1. Fold back the cover.
2. Press the
Jets
or
Jets 1
button.
3. Carefully measure the recommended amount of chemical and slowly pour it into the filter area. Use care not to splash chemicals on your hands, in your eyes, on the spa surface, or on the siding.
4. Close the spa cover.
Warning:
High sanitizer levels can cause discomfort to the user’s eyes, lungs and skin. Always allow the sanitizer level to fall to the recommended range before using the spa.
IMPORTANT NOTE REGARDING SHOCK TREATMENT:
After administering shock to your spa, leave the cover open for a minimum of 20 minutes to allow the oxidizer gas to vent. A high concentration of trapped oxidizer gas which may exist as a result of the shock treatment (not daily sanitation) may eventually cause discoloration or vinyl degradation to the bottom of the cover. This type of damage is considered chemical abuse and is not covered under the terms of the limited warranty.
1. Balancing the Water Chemistry Levels
Maintaining spa water chemistry can be tricky, especially since there are many methods of keeping your water clear and clean. Follow the maintenance schedule on page 31 to determine how often you should test your water.
We do not recommend any brand of chemical. See page 31 for a table of common chemicals used in spas and their generic equivalents.
See a spa dealer for guidance and recommendations on spa chemicals and supplies. Various chemicals often sold under brand names, but a spa dealer can advise you on generic chemicals that are often much less costly than proprietary brands.
Balancing the Total Alkalinity (TA)
Total Alkalinity is a measure of the total levels of carbonates, bicarbonates, hydroxides, and other alkaline substances in the water.
TA is referred to as the water’s “pH buffer”. In other words, it’s a measure of the ability of the water to resist changes in pH level.
TA too high
pH will be too high and may be difficult to stabilize pH
180
160
140
Add an alkalinity decreaser
If the TA is too low, the pH level will fluctuate widely from high to low. Fluctuations in pH can cause corrosion or scaling of the spa components. Low TA can be corrected by adding sodium carbonate
(pH/Alkalinity Up).
TA balance
120
100
80
Ideal TA balance
If the Total Alkalinity is too high, the pH level will tend to be high and may be difficult to bring down. It can be lowered by using sodium bisulfate(pH/Alkalinity Down).
TA too low
pH will fluctuate wildly
60
40
20
Add an alkalinity increaser
Once the TA is balanced, it normally remains stable, although the addition of more water with a high or low alkalinity will raise or lower the TA reading of the water.
Causes scale to deposit on spa and
When the Total Alkalinity is within the recommended range, proceed to the next step.
275
250
225
Dilute the spa with soft water
200
CH balance
175
150
Ideal CH balance
2020 Portable Spas - LES
LTR20201163, Rev. Z3
CH too low
Causes equipment corrosion
125
100
75
Add a calcium hardness increaser
www.calspas.com
pH too high
Too alkaline, causes scaling
pH balance pH too low
Too acidic, causes corrosion
7.2
7.0
6.8
6.6
8.2
8.0
7.8
7.6
7.4
Add a pH decreaser
Ideal pH balance
Add a pH increaser
27
28
TA too high
pH will be too high and may be difficult to stabilize pH
TA balance
180
160
140
120
100
80
Add an alkalinity decreaser
Ideal TA balance
Balancing the Calcium Hardness (CH)
Calcium Hardness is a measure of the total amount of dissolved calcium in the water. Calcium helps control the corrosive nature of the spa’s water. That’s why calcium-low water (commonly known as “soft” water) is not recommended. It is very corrosive to the equipment, and can cause staining of the spa shell.
If the CH is too high (commonly known as “hard water”), formation of scale on the spa’s shell surface and equipment can result. You can use a generic calcium remover to remove hardness from water. CH can also be decreased by dilution – a mixture of 75% hard and 25% soft water will usually yield a reading within the correct range. If soft water is not available or practical for you, a stain and scale inhibitor should be added to the spa water, according to label instructions.
If the CH is too low add CH Increaser.
Balancing the pH
8.0
Add an alkalinity decreaser
Dilute the spa with soft water
Ideal TA balance
Dilute the spa with soft water
Add a pH decreaser
Once the CH is balanced, it normally remains stable, although the addition of more water with a high or low calcium content will raise or lower the CH reading of the water.
When the CH is within the recommended range, proceed to the next step.
The pH level is the measure of acidity and alkalinity. Values above
7.8 are alkaline; those below 7.2 are acidic. Maintaining the proper pH level is extremely important for optimizing the effectiveness of the sanitizer, maintaining water that is comfortable for the user, and preventing equipment deterioration.
If the spa water’s pH level is too low, the following may result:
• The sanitizer will dissipate rapidly.
• The water may become irritating to spa users.
• The spa’s equipment may corrode.
TA too low
pH will fluctuate wildly
TA too high
and may be difficult to stabilize pH deposit on spa and
TA balance
CH balance
TA too low
pH will fluctuate wildly
Causes equipment
CH too high
deposit on spa and
Too alkaline, causes scaling
CH balance pH
CH too low
Too acidic, causes corrosion
pH too high
Too alkaline, causes scaling
pH balance pH too low
Too acidic, causes corrosion
60
40
200
175
150
125
250
225
7.6
7.4
7.2
7.0
8.0
7.8
7.6
7.4
7.2
7.0
6.8
6.6
Add an alkalinity increaser
Ideal CH balance
Add an alkalinity increaser
Add a calcium hardness increaser
Ideal CH balance
Ideal pH balance
Add a calcium hardness increaser
Add a pH increaser
Add a pH decreaser
Ideal pH balance
Add a pH increaser
If the pH is too low, it can be increased by adding sodium hydrogen carbonate (pH/Alkalinity Up) to the spa water.
If the pH level is too high, the following may result:
• The sanitizer is less effective.
• Scale will form on the spa shell surface and the equipment.
• The water may become cloudy.
• The filter cartridge pores may become obstructed.
If the pH is too high, it can be decreased by adding sodium bisulfate (pH/Alkalinity Down) to the spa water.
NOTE: After adding sodium hydrogen carbonate or sodium bisulfate, wait two hours before testing the water for pH.
Measurements taken too soon may not be accurate.
It is important to check the pH on a regular (weekly) basis. The pH will be affected by the bather load, the addition of new water, the addition of various chemicals, and the type of sanitizer used.
When the pH is within the recommended range, proceed to sanitation.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
2. Sanitation and Shock
Sanitizers kill bacteria and other organic waste by breaking them down to non-harmful levels which are filtered out.
Before you fill your spa, you need to decide which chemical sanitizer you wish to use. Consult your Cal Spas dealer for the right decision with regards to your lifestyle and spa usage.
We recommend either
bromine
or
chlorine
as your sanitizer. Both work well when maintained regularly.
DO NOT use Trichlor. Trichlor is very acidic and the hot temperature of the spa causes it to dissolve too quickly. It will cause damage to your spa and will void your warranty.
Whichever plan you decide on, follow it completely and don’t take shortcuts. It will provide you with clean, safe, clear spa water with a minimum of effort. Spa owners with an ozonator still need to use a chemical sanitizer. See page
34 for a description of how the ozonator works.
Whenever you test your chemical levels, your test strip will likely have a test for chlorine or bromine. Make sure your sanitizer falls within the range shown below.
Testing For:
Chlorine Level
Without ozonator
With ozonator
Bromine Level
Without ozonator
With ozonator
Ideal Range (ppm)
Minimum Maximum
3.0 5.0
2.0 4.0
6.7 11.0
5.7 10.0
Starting and Maintaining Sanitizer Levels
Sanitizing your spa with chlorine or bromine is very similar.
Each sanitizer has its advantages and disadvantages.
Bromine:
Whereas chlorine can sometimes cause offensive odors and skin irritation, bromine is less likely to do so.
Additionally, unlike chlorine, when bromine combines with bather waste and other contaminants in the water, it remains a very effective sanitizer. Bromine is also far less pH-dependent than chlorine.
Always remember that bromine by itself is not a sanitizer, and it needs to be activated by shock in order to be effective.
Chlorine:
The most commonly recognized sanitizer is chlorine. However, the effectiveness of chlorine depends heavily on the pH level of the spa water. In order to get the most effective and economical benefit of chlorine, you must maintain a consistent pH level of between 7.2 to 7.6.
A disadvantage of using chlorine is that when chlorine combines with bather waste and other contaminants in the water, not only does it lose its sanitizing ability, it can cause odors and irritate eyes and skin.
1. Establish a baseline by adding either granulated chlorine or bromine.
• Use half an ounce of chlorine for every 500 gallons of water.
• Use half an ounce of bromine for every 100 gallons of water.
2. Run the jets for 10 minutes.
3. Test the water. Make sure the pH, TA, and CH levels all fall within the ranges shown on the previous page.
Make adjustments where they are needed.
4. At this point, if you use bromine, it is not yet activated and
it will not sanitize the water
. You need to shock-oxidize the spa water. Depending on the size of your spa, add one to two ounces of shock. You can use any kind of shock you want.
5. Test the water again. When the water is balanced, your spa is ready to use.
After you choose a sanitizer, you will need to establish a baseline and maintain it regularly.
Starting with fresh water:
Note: If you choose to use bromine, we do not recommend using a floater. You have more control over the bromine level by adding bromine as needed. For more discussion on this, see page 32, “Common Water Chemistry Questions”.
29
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
30
Shocking the Water
In addition to using a chemical sanitizer, you will periodically need to shock the water. Shocking helps refresh the water by breaking down organic waste contaminants which cause odor and cloudy water. After treatment, water quality and clarity is often completely restored.
The two types of shock are sodium dichlor and potassium monopersulfate (MPS). You can use either type of shock regardless of which sanitizer you use. Even if you use bromine, you can use a chlorinated shock if you wish -- in fact, you may find a chlorinated shock is more effective than dichlor or MPS alone.
If irritating chloramines are present, shocking also converts them back to active chlorine. If you use bromine sanitizer, shocking activates the bromide ion (which by itself has no disinfecting capability) which becomes hypobromous acid in water, a good sanitizer.
Add one ounce of oxidizer shock once a week, after heavy bather loads, or if water has a strong odor.
Spa must be running with all of the jets on high for 30 minutes with the cover open. If necessary, repeat shock in
30 minute intervals.
3. Filtration
The filter is the part of your spa that removes the debris from the water and needs to be cleaned on a regular basis to maximize your spa’s filtering performance and heating efficiency.
It is extremely important that you never run the spa without a filter. There is a possibility that debris may be sucked into the plumbing through the filter well.
Cleaning the Filter
In addition to spraying off the filter weekly to remove surface debris, your filter should be deep cleaned periodically to dissolve scale and particles that get lodged deep within the filter fibers and impede the filtration process. Even if the filter looks clean, scale and particles can clog the fibers and prevent water from flowing through the filter resulting in the most common spa problem—no heat, caused by a dirty filter.
We recommend you clean your filter at least once a month, possibly every two weeks depending on how frequently you use your spa, and replace it once a year or as necessary. See page 38 for instructions on removing and cleaning the filter.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
4. Regularity (Maintenance Schedule)
Prior to each use
Test the spa water. Adjust chemical levels as necessary.
Shock the water by adding ½ teaspoon of sodium dichlor per 250 gallons or 1 teaspoon of MPS per 250 gallons.
After each use
Once a week
Add an ounce of oxidizer after heavy bather loads (see page 30 on shocking the water).
Check the filter well and inside the filter pipe for leaves and foreign matter.
Every two to four weeks
Every two to four months
Test the spa water. Adjust chemical levels as necessary.
Shock the water by adding ½ teaspoon of sodium per 250 gallons or 3 teaspoons of
MPS per 250 gallons.
If your water source is high in calcium, add stain and scale preventer.
Deep clean your spa’s filter (see page 38). How often you clean your filter depends on how much you use your spa. There is no harm in frequently cleaning your filter and will only help your spa’s efficiency.
Change the spa water. How often you change the water depends on how much you use the spa. When you change the water, you will need to:
• Clean and polish the acrylic surface (see page 40)
• Clean and treat the spa cover and pillows (see page 40)
• Deep clean the filter (see page 38)
• Refill your spa (see page 7)
Each time you refill the spa
Follow the section “Filling and Powering Up Your Portable Spa” on page 7
.
Once a year
Replace filter cartridges if the pleats appear frayed (see page 38).
Generic Names for Chemicals
Water Chemistry
Common name
pH Up pH Down
Alkalinity increaser
Alkalinity decreaser
Calcium increaser
Calcium decreaser
Usual chemical name
sodium hydroxide sodium bisulfate sodium bicarbonate (baking soda) sodium carbonate sodium carbonate sodium bicarbonate (baking soda) sodium bisulfate
Common brand names
pH Increaser, pH Up, pH Plus, pH Booster pH Decreaser, pH Down, pH Minus, pH
Subtractor, Dry Acid
Alkalinity Increaser, Alkaline Up
Alkalinity Decreaser, Alkaline Down calcium chloride Calcium Increaser, Calcium Up, Calcium Plus,
Hardness Increaser
N/A To decrease calcium hardness, drain several gallons of water from the spa and refill using a mixture of 75% hard water and 25% soft water, or use a stain and scale inhibitor.
31
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
32
Sanitizers
Common name
Chlorine
Bromine
Usual chemical name
sodium dichlor sodium bromide
Common brand names
Both chlorine and bromine are available under numerous brand names
Shock
Common name
MPS
Dichlor
Usual chemical name
monopersulphate sodium dichlor
Common brand names
MPS Shock, Oxy-Spa, SeaKlear
Dichlor Shock
Note: Dichlor (chlorine) is both a sanitizer and a shock. Monopersulphate (MPS), when used as a shock, can be purchased alone as non-chlorinated shock or combined with dichlor, which makes it significantly more effective than MPS alone.
Other chemical additives
Common name
Stain and scale inhibitor
Foam inhibitor
Clarifier
Do NOT use these in your spa:
Usual chemical name Common brand names
These are usually proprietary chemical formulations and cannot be purchased as a single generic chemical.
Metal Stain Gone, Scale Inhibitor, Stain and
Scale Preventer, Stain and Scale Defense
Foam Gone, Foam Down, Defoamer
Water Brite, Spa Bright, Water Clarifier, Clear
Water, Natural Clarifier, Brite & Clear
• Sodium hypoclorite (household bleach)
• Trichlor
• Chemical floaters
• Bromine tablets
• Muriatic acid
• Borax or boric acid in any form, including brand names such as 20 Mule Team Borax or generic as sodium tetraborate
• Cyanuric acid, also called sun protector or chlorine protector
Common Water Chemistry Questions
Question:
Why is the use a floater not recommended to sanitize my spa water?
Answer:
We do not recommend the use of a floater for three reasons:
• The floater is unable to control the rate at which the sanitizer is dissolved into the water. When a floater is first placed in a spa, the sanitizer level can be extremely high. High sanitizer levels can chemically burn or discolor the spa’s shell or the underside of the cover. Then, after a period of time, the sanitizer level dispensed by the floater will fall to near zero. A low sanitizer level will allow viruses, bacteria or algae to grow.
• Floaters tend to stay in one area of the spa most of the time, causing this area to be exposed to extreme sanitizer levels.
• The floater may allow pieces of the highly concentrated sanitizer to fall out and settle on the floor or seat of the spa shell. These pieces of sanitizer will chemically burn (blister) the spa shell. Although your spa shell is specifically designed to resist the effects of spa chemicals, no spa surface can withstand this type of highly concentrated chemical. Remember, chemical abuse is specifically not covered under the terms of the warranty.
Question:
When I open my spa, I smell chlorine. How do I get rid of this smell?
Answer:
There are two types of chlorine in your spa. The first is the Free Available Chlorine, which is the chlorine available to sanitize your spa. This free Available Chlorine does not have an odor. The second is Chloramine, which is residue from chlorine already expended. Chloramines have a strong chlorine odor. The smell from
Chloramines can be eliminated by shocking the water. If you smell chlorine in the water, your spa is reminding
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
you to add a shock treatment.
Question:
Why can’t I fill my spa with soft water?
Answer:
Soft water is essentially the same as regular water, except that most or all of the calcium has been replaced by sodium. Soft water may be corrosive to the heater and other components. Replacement of spa components damaged by soft water is extremely expensive.
Question:
I am trying to reduce the number of chemicals to which my family is exposed. Do I really need to use so many chemicals and in such large amounts?
Answer:
While over-exposure to any chemical can be unhealthy, many low levels of chemicals are effective and beneficial. In the case of spa water, the chemicals we recommend are needed to protect the user from waterborne pathogens (disease-causing microbes) and to prevent corrosion of spa components.
Question:
Why isn’t water chemistry damage covered by the warranty?
Answer:
The chemical levels and water quality of the water in the spa are under your direct control. With proper basic care, the spa will provide many years of hot water relaxation. If you are unsure about any chemical or its usage in the spa, contact your spa dealer.
Do’s and Don’ts
• DO add all chemicals slowly into or in front of the filter compartment with the jet pump operating for ten minutes.
• DO use special care if using baking soda to clean either the interior or exterior plastic surfaces.
• DO use only a granular form of bromine sanitizer.
• DON’T use swimming pool (muriatic) acid to lower pH.
• DON’T splash pH increaser additives on the siding.
• DON’T use compressed sanitizers.
The use of bromine sticks or tablets in floaters, which may become trapped in a lounge or cooling seat (or sink to the spa floor), have been shown to cause discoloration of or surface distress to a spa’s shell.
• DON’T use a floater type sanitization system as a low or no maintenance solution to your spa maintenance program.
Floating dispensers can become trapped in one area and cause an over-sanitization (or chemical burn) of that particular area.
If the dispenser setting is too high, the high concentration can discolor the spa shell and damage the underside of the cover.
Automatic floating dispensers have a tendency to either over-brominate or under-brominate as the rate of erosion varies greatly. Damage to the spa and cover can occur very quickly.
• DON’T use a sanitizer which is not designed for spas.
• DON’T use household bleach (liquid sodium hypochlorite).
• DON’T broadcast or sprinkle the chemicals onto the water surface. This method may cause chemically-induced spa surface blistering (chemical abuse).
33
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
34
Bather Load
“Bather Load” is the term used to describe the number of people using a spa, combined with the length of usage, and the frequency of usage. All these factors have a great effect on the spa water. The higher the bather load, the more chemicals need to be added and a longer filtration time will be needed.
Recommendations are designed for spas with average bather load (3 to 4 people, 15 minutes of usage, three times a week at 100 degrees) If your bather load exceeds these guidelines, and you experience water quality problems, increase the amount of filtration first, (go to the next higher filtration number) then if water quality is still not adequate, consult the advice of your Cal Spas dealer for additional chemical or system recommendations. Be sure to give them your bather load information.
Ozonator
The ozone generator releases ozone into the spa water. You will still need to test for chlorine or bromine and occasionally replenish it to return the sanitizer level to the baseline.
For spas without a circulation pump, pump 1 will run at low speed and the ozonator will run during filtration. You will need to increase your filtration to a minimum of six hours per day.
For spas with a circulation pump, the ozonator will run with the circulation pump.
The spa’s control system is factory-programmed with one filter cycle that will run in the evening when energy rates are often lower. The time and duration of the filter cycle can be set according to your needs. In addition, a second filter cycle can be enabled. Filtration time may need to be increased with heavy bather load.
See instructions for setting filtration cycles on page 16.
Always make sure water diverter valves are turned all the way to the left or right and never left in the center position during filtration cycles. When the diverter valve is in the center position, there is not enough suction from the pump in order to inject ozone into the spa. The ozonator will generate ozone, but it will not be injected into the water.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Troubleshooting Water Clarity Problems
Problem
Cloudy Water
Water Odor
Probable Causes
Dirty filter
Excessive oils / organic matter
Improper sanitization
Suspended particles / organic matter
Overused or old water
Excessive organics in water
Improper sanitization
Low pH
Chloramine level too high
Low pH
Bacteria or algae growth
Buildup of oils and dirt
Chlorine Odor
Musty Odor
Organic Buildup /
Scum Ring Around
Spa
Algae Growth
Eye Irritation
Skin Irritation /
Rash
Stains
Scale
High pH
Low sanitizer level
Low pH
Low sanitizer level
Unsanitary water
Free chlorine level above 5 ppm
Total alkalinity and/or pH too low
High iron or copper in source water
High calcium content in water – total alkalinity and pH too high
Possible Solutions
Clean filter and run jet pump
Shock spa with sanitizer
Add sanitizer
Adjust pH and/or alkalinity to recommended range
Drain and refill the spa
Shock spa with sanitizer
Add sanitizer
Adjust pH to recommended range
Shock spa with sanitizer
Adjust pH to recommended range
Shock spa with sanitizer – if problem is visible or persistent, drain, clean and refill the spa
Wipe off scum with clean rag – if severe, drain the spa, use a spa surface and tile cleaner to remove the scum and refill the spa
Shock spa with sanitizer and adjust pH
Shock spa with sanitizer and maintain sanitizer level
Adjust pH
Shock spa with sanitizer and maintain sanitizer level
Shock spa with sanitizer and maintain sanitizer level
Allow free chlorine level to drop below 5 ppm before spa use
Adjust total alkalinity and/or pH
Use a stain and scale inhibitor
Adjust total alkalinity and pH – if scale requires removal, drain the spa, scrub off the scale, refill the spa and balance the water
Use a stain and scale inhibitor
35
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
36
Cleaning and Maintenance and Sound System
Removing and Reseating the Pillows
You can remove the pillows for cleaning and maintenance quickly and easily. This method works for all types of pillows.
Grab the lower edge of the pillow with both hands firmly and pull up. As you do this, the pillow inserts will pop out of the holes.
Reseat the pillows by aligning the pillow inserts with the holes and striking the pillow hard enough to insert the pegs back into the holes.
Jet Removal and Replacement
Jets can be easily removed for cleaning.
Screw-in jet removal
Grasp the outer rim of the jet and turn it counter-clockwise. The jet will unscrew from the fitting until it is free.
To replace the jet, place it in the fitting and turn it clockwise until it is snug in place and it can be rotated freely about half a turn. Do not overtighten the jet.
Snap-in SQR jet removal
Grasp the outer rim of the jet and turn it counter-clockwise until it completely stops.
You may feel it slightly loosen pop out a bit from the fixture. Pull the jet out from the jet fixture. The jet will be very snug and may require some force to remove it. DO NOT PRY
OUT JETS.
To replace any jet, place it in the fitting and turn it clockwise until it snaps in and can be rotated freely about half a turn. Do not overtighten the jet.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Draining Your Portable Spa
Your spa should be drained every four to six months for cleaning and maintenance and refilled with fresh tap water. See page 40 for instructions on cleaning the shell, cover, and pillows. See page 7 for instructions on refilling your spa.
Before you begin, turn off power to the spa at the breaker and remove all filters.
1. Locate your drain.
For spas with drain inside the spa
Using a Phillips screwdriver, remove the screws to the access panel and open it. Locate hose ending with the ¾ inch hose-bib fixture as shown below.
For spas with cabinet-mounted drain
Pull the knob out of the cabinet. The cabinet drain is screwed into the drain pull knob.
37
2. Remove the cap.
Make sure the valve is in the closed position, then unscrew and remove the cap. Unscrew the cap.
For spas with drain inside the spa For spas with cabinet-mounted drain
3. Connect valve to a garden hose.
Attach a garden hose to the hose-bib fixture. Place the other end of the garden hose where you would like the water to drain.
4. Drain the spa.
Turn the valve on the hose-bib fixture to open the drain.
When the spa has drained completely, turn the valve on the hose-bib fixture, remove garden hose, and replace the cap.
For all spas
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
38
Winterizing (Cold Climate Draining)
In many areas of the country, the temperature drops below 32˚F (0°C). We recommend that you always have your spa full of water and running at normal spa temperatures (80˚F to 100˚F, 26.7°C to 37.8°C). This will help reduce the risk of freezing in your spa and your spa’s equipment.
Warning: If you find the need to drain your spa, be aware of the potential of freezing in your spas equipment and plumbing. Even if the directions below are followed perfectly, there is no guarantee that your spa will not suffer freeze damage. Freeze damage is not covered by your warranty.
1. Remove the filter baskets and filters.
2. Drain your spa completely as described in the instructions above.
3. Vacuum water from the spa’s main drain and from the jets with a wet/dry vacuum.
4. Open the bleeder valves on the pumps.
5. Disconnect the unions from both sides of all pumps.
6. Blow any remaining water out of the jets and equipment area with the wet/dry vacuum.
7. When the spa has completely finished draining, close the bleeder valves and re-connect the unions on all pumps. Replace the filters and filter baskets.
8. Cover your spa with a good spa cover and an all-weather tarp to ensure that neither rain nor snow enters the spa.
Cleaning and Replacing the Filter
Filtration is one of the most important steps you can take to ensure clean, clear water. It is far less expensive to fix water clarity problems by filtering your spa than by using excessive amounts of chemicals, excessive filtration times, or by water replacement.
See the section “Cleaning the Filter” on page 30 for more information.
Set the spa in SERENITY MODE before you remove the filter. SERENITY MODE pauses all spa operations for service functions like cleaning or replacing the filter. See page 14 for instructions on using SERENITY MODE.
1. Remove the filter by unscrewing it and pulling it up and out.
2. Place the dirty filter into a bucket of water deep enough to cover the filter. Add 8 oz. of liquid filter cleaner to the bucket of water.
Note:
It is a good idea to keep a spare filter to use in the spa while the dirty filter is being deep cleaned. This way, you can rotate the filters and both will last longer.
3. Soak the filter for a minimum of 24 hours.
4. Spray the filter with a water hose. Spray each pleat carefully.
5. Reinstall the filter. Do not overtighten.
Spa Cover and Locking System Installation
Important! Keep the spa covered when not in use!
• Covered spas will use less electricity in maintaining your set temperature.
• Covering your spa will protect your spa’s finish from the sun’s ultraviolet rays.
• You are required to keep the spa covered to maintain warranty coverage.
• Covering your spa helps prevent children from drowning in the spa.
In addition, while the spa cover is rigid, it is not designed to support any weight. Therefore, as a safety precaution and to preserve the life of your cover, you must not sit, stand, or lie on it, nor should you place objects of any kind on top of it.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Step 1
- Place cover on spa. Make sure it is correctly positioned.
Step 2
-
Position the tie-down hardware (attached to the straps of your cover) on the side of the spa so they are easily reached by the cover tie-down straps.
39
Step 3
-
With the straps pulled taut (but not overly tight), lightly drill the location for screw placement. Gently drill 3 holes - one for each screw slot in the lock. (If you do not have a low torque drill, use the lowest torque setting on the drill you have.) DO NOT drill all the way in but instead just make a guide for starters.
Step 4
-
Use a screwdriver to finish screwing in the 3 screws. (Repeat this process for the other 3 corners.)
Step 5
- Keep the cover fastened down at all times when not in use. Locking hardware may be locked with a key (which is provided).
Step 6
- The provided key will allow you to lock down spa access.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
40
Vacation Care
You can leave your spa unattended for up to two weeks if you follow these instructions.
ALWAYS lock your cover using the cover locks if you plan to be away from home and the spa is filled with water.
1. Select the Low Range temp choice used for vacation mode.
2. Following the water quality instructions starting on page 25, adjust the pH.
3. Shock the water (add either chlorine or bromine sanitizer).
4. When you return, check and adjust the pH and shock the water.
If you will not be using your spa for longer than 14 days and a spa maintenance service is not available, we strongly recommend you drain or winterize your spa.
Cleaning Your Spa
Spa Cover and Pillows
Due to the constant punishment your spa cover and pillows receive, you should protect them by applying a vinyl and leather cleaner as part of your monthly maintenance plan. Use a product that is specifically designed to protect spa covers and pillows from chemical and ultraviolet light damage without leaving an oily residue behind that is normally associated with common automotive vinyl protectants.
Warning:
Do not
use automotive vinyl protectants on spa covers or pillows. These products are generally oil-based and will cause severe water clarity issues that are difficult to correct.
Spa Shell
Each time you drain your spa, before you refill it you should clean your spa shell with an all-purpose cleaner and apply a coat of surface protectant.
Use a low detergent, non-abrasive cleaner specifically formulated to clean the spa without damaging its acrylic finish.
Use a non-oil based surface protectant that is specifically formulated to protect the spa’s finish from the chemicals and minerals associated with normal spa use.
Using the Freedom Sound System
The Freedom Sound System
™
entertainment option contains a Bluetooth-enabled speaker system that is available for certain Cal Spa models. Any Bluetooth-enabled device can be used to play audio through your spa.
Before you can use the sound system, you need to pair the Bluetooth module with your device. The Bluetooth module is installed within the spa cabinet. Everything can be done with your device. The example shown below is from an iPhone device. Your device may appear differently. Before you begin, make sure Bluetooth in enabled on your device.
1. Select Bluetooth from your device’s option list.
2. Select
SWA8-6BT...
from the list of available devices to pair.
3. Allow your device to pair with the spa’s Bluetooth module.
4. When the devices have been connected, the device
SWA8-6BT...
will be highlighted.
Only one Bluetooth device can be paired with the Freedom Sound System
™
at any time.
Once your device is paired and connected, all sounds from your device will be played through the sound system, including system sounds and telephone.
1 2 3 4 www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Appendix
Replacement Parts
Screw-in Jet Inserts
Description Used by
ELE 2” Euro No Eyeball
PLUCS2295021S
Patio
Patio+
Inground Spas
Please visit www.quickspaparts.com to order your replacement parts.
Screw-in Jet Inserts
Description Used by
MFD 3.5” Maxi Flow Directional
PLUCS2295091S
Patio
Patio+
Inground Spas
41
ED 2” Euro Directional
PLUCS2295051S
MED 3” XL Cluster Storm
Directional
PLUCS2295031S
Patio
Patio+
Inground Spas
PSD 5” Power Storm
PLUCS2295131S
Patio
Patio+
Inground Spas
Patio
Patio+
Inground Spas
mfd 3” Micro Flow Directional
PLUCS2295061S
Patio
Patio+
Inground Spas
ET 2” Cluster Storm Twin
PLUCS2295161S
MMP 3” Mini Multi-Massage
PLUCS2295171S
Patio
Patio+
Inground Spas
Patio
Patio+
Inground Spas
Note:
All Cal Spa models use a combination of screw-in and snap-in jet inserts where removable jets are used.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
42
Screw-in Jet Inserts
Description Used by
PSTR 5” Power Storm Twin Roto
PLUCS2295181S
Patio
Patio+
Inground Spas
Please visit www.quickspaparts.com to order your replacement parts.
Screw-in Jet Inserts
Description Used by
T 5” Tornado Adjustable
PLUCS2295201S
Patio
Patio+
Inground Spas
MMP 5” Power Storm Riffed
PLUCS2295141S
Patio
Patio+
Inground Spas
2” Neck Jet Directional
PLU29923-014-000
Patio
Patio+
Inground Spas
PST 5” Power Storm Wagon Wheel
PLUCS2295191S
Patio
Patio+
Inground Spas
www.calspas.com
If you need jet bodies, go to www.quickspaparts.
com or refer to the Cal Spa Replacement
Parts Catalog, which can be downloaded from www.calspas.com/replacementparts.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Water Diverter Valves
Diverter Valve 2” Titanium
Black (CS600303T1-TT)
PLU21300465
Diverter Valve 1” Titanium
Black (CS600426T1-TT)
PLU21300453
Diverter Valve 1½” On/Off
ASSY (600-4601)
PLU21100045
Air Control Valve
Air Control with Titanium
Black CS660350T1-TT
PLU21300504
Aquatic Air Therapy (AAT)
Air Control
PLU25059-211-00
Drains
Drain Super Hi Flo Suction
2½” Black (640-3581LGV)
PLU21400146
Low Profile Drain ¾” Black
(640-0511)
PLU21400401
Please visit www.quickspaparts.com to order your replacement parts.
Pillows
Cascade Pillow No
Insert Black
ACC01401031
43
Infinity Pillow Ribbed
Black
ACC01401051
Infinity Pillow Plain
Black
ACC01401061
Y Pillow recess
ACC01401101
50 sq ft
Filters
FIL50-5D13H15FCT-3
2020 Portable Spas - LES
LTR20201163, Rev. Z3
If you need jet bodies, go to www.quickspaparts.
com or refer to the Cal Spa Replacement
Parts Catalog, which can be downloaded from www.calspas.com/replacementparts.
www.calspas.com
44
Please visit www.quickspaparts.com to order your replacement parts.
Filters
FIL75-5D17H15FCT-3
75 sq ft
FIL75-7D155H2MCT-3
75 sq ft
Mega
DYNA FLO
XTRA Lo-Pro
75 SQ. Ft.
FIL11703305
2” CV, 4
SCALLOP
(less cartridge)
50 square foot teleweir skimmer:
Teleweir Skimmers
Filter attaching cap assembly
FIL11700013
Filter skimmer inner pipe
FIL11700012
75 square foot teleweir mega skimmer:
Filter attaching cap assembly
FIL11700025
Filter skimmer inner pipe
FIL11700026
Waterfalls
Cascade II Waterfall
Black textured with valve and logo 12
-3/8” ‘14
PLU21800825TEX
Cascade II Waterfall
Curved Black
Textured with Valve and Logo 12-3/8”
‘14
PLU21800828
If you need jet bodies, go to www.quickspaparts.
com or refer to the Cal Spa Replacement
Parts Catalog, which can be downloaded from www.calspas.com/replacementparts.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
1-LED light string
LIT16100330
2-LED light string
LIT16100331
LED Lights
4-LED light string
LIT16100332
1 to 3 ext. cord
LIT16100335
1 to 1 port ext. cord
LIT16100338
Please visit www.quickspaparts.com to order your replacement parts.
LED Lights
Interior light with logic
(7 LED)
LIT16100333
Interior light without logic
(7 LED)
LIT16100337
Main light housing, LED lens, fitting nut
LIT16100336
Replacement Cabinet Panels
The complete selection of replacement cabinets for all models is very extensive and too lengthy for this owner’s manual. To order replacement panels for your spa, visit www.quickspaparts.com.
45
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
46
Covers
All spa covers are designed with a tapered height, angling downward from the center to the sides to drive off rain and prevent water from pooling. The covers listed below are filled with either 1.5 lb or 2.0 lb foam.
Standard
4” - 2.5”
1.5 Lb. foam
Deluxe
5” - 3”
2.0 Lb. foam
Taper Dark
Brown
Basic
54” x 78”
Fits spa models: PZ-
517L, PPZ-525L
64” x 84”
Fits spa model:
PPZ-537L
72” x 72” triangle
Fits spa models:
PZ-617T, PPZ-628T
78” x 84”
Fits spa models:
PZ-621L, PPZ-631L
78” round
Fits spa model:
P2511R
87” x 87”
Fits spa model:
EP-760DL, EC-754DL
COV5478BDB-3
COV6484BDB-3
COV7272TRBDB-3
COV7884BDB-3
COV78RDBDB-3
COV8787BDB-3
Taper Black
Basic
COV5478BBK-3
COV6484BBK-3
COV7272TRBBK-3
COV7884BBK-3
COV78RDBBK-3
COV8787BBK-3
Taper Gray
Basic
COV5478BG-3
COV6484BG-3
COV7272TRBG-3
COV7884BG-3
COV78RDBG-3
COV8787BG-3
Taper Dark
Brown
Standard
COV5478SDB-3
COV6484SDB-3
Taper Black
Standard
Taper Gray
Standard
COV7272TRSDB-3 COV7272TRSBK-3 COV7272TRSG-3
COV7884SDB-3
N/A
COV8787SDB-3
COV5478SBK-3
COV6484SBK-3
COV7884SBK-3
N/A
COV8787SBK-3
COV5478SG-3
COV6484SG-3
COV7884SG-3
N/A
COV8787SG-3
93” x 130”
Fits spa model: EC-947E
84” x 84” (7 foot spas)
Fits spa models: P2-722L,
P2-722B, PP-732L+, PP-732B+,
EC-735L, EC-735B, EC751L,
EC751B, EP-761L, EP-761B,
PL-760L, PL-760B, PPL7L+
93” x 93” (8 foot spas)
Fits spa models: EC-835L,
EG835B, EC-851L, EC-851B,
EC-852L, EC-864L, EC-864B,
EP-861L, EP-864B, PL-860L,
PL-861B, PL-880L, PL-881B,
PPL-8B+
Black
Deluxe
COV93130DBBK-3
N/A
N/A
Taper Black
Deluxe
COV93130DBK-3
Taper Dark Brown
Deluxe
COV93130DDB-3
Taper Gray
Deluxe
COV93130DG-3
COV8484SBK-3
(Standard)
COV9393DBK-3
COV8484SDB-3
(Standard)
COV9393DDB-3
COV8484SG-3
(Standard)
COV9393DG-3
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Basic Troubleshooting
The troubleshooting guidance provided here is intended to cover the most common problems a spa owner may encounter.
For more in-depth troubleshooting, go to www.calspas.com/troubleshooting.
Possible Solutions Symptom
Problems starting up
Pump won't prime
Breaker keeps shutting off
See priming instructions on page 10.
Reset the GFCI breaker. If this continues, contact your dealer or a qualified spa technician.
Power and system problems
System won’t start up or breaker keeps shutting off
Control panel doesn’t respond
Spa does not turn off
Power may be shut off. Turn on GFCI circuit breaker. If this continues, contact your dealer or a qualified spa technician.
Turn on or reset the GFCI circuit breaker. If this does not solve the problem, contact your dealer or a qualified spa technician.
If you hear the pump running but the control panel doesn’t respond, contact your dealer
Spa may be trying to heat up. Check if spa is in Ready or Rest mode.
In cold climates, if spa is not equipped with full foam or any kind of insulation, it will try to maintain the set temperature. Set the spa to low temperature range and set the temperature to 80°F.
Spa may be in filter cycle. If it is, this is normal and no adjustment is necessary.
There may be a problem. See Error Screens on page 15.
Message on the control panel
Heat problems
Spa water does not get hot Spa may be in low temperature range. Set the spa to high temperature range.
The filter may be dirty or may need to be replaced. Clean or replace the filter.
The water level may be too low. Fill the spa with water level at 4 to 6 inches from the top.
The temperature is not turned up high enough. Raise temperature on topside control.
Cover the spa. The cover will keep heat in the spa and help keep heat from escaping. Make sure cover is on at all times when spa is not in use.
The heater element may be old, deteriorated, coated with scale, or defective.
Contact your dealer for more assistance.
The gate valves may be partially or completely closed. NEVER OPERATE YOUR
SPA WITH THE GATE VALVES CLOSED!
47
If you need jet bodies, go to www.quickspaparts.
com or refer to the Cal Spa Replacement
Parts Catalog, which can be downloaded from www.calspas.com/replacementparts.
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
48
Please visit www.quickspaparts.com to order your replacement parts.
Symptom
Spa overheats - temperature greater than 110°F / 43°C
Possible Solutions
Overheating can occur during summer months and may not necessarily indicate a malfunction. When it occurs, a message code may also appear on the control panel.
Temperature may be set too high. Turn the set temperature down to a lower temperature.
Filtration time may be too long. Turn the filtration cycles down during the warm months.
The spa may not be properly ventilated. Make sure the front of the spa is not blocked to allow air flow.
High speed pumps may have been running too long. Limit pump running time to no more than 15 to 30 minutes.
Water pressure problems
Low water pressure
No water pressure (no water stream from any jets)
Jets surge on and off
Pump problems
Pump runs constantly – will not shut off
Noisy pump
Jet valves may be partially or fully closed. Open the jet valves.
Filter cartridge may be dirty. Clean or replace the filter.
Pump may have airlock. Remove airlock by priming spa (page 10)
The suction fittings may be blocked. Remove any debris that may be blocking them.
The filter skimmer may be blocked. Remove the blockage.
Gate valves may be closed. Open gate valves. Note: Never operate your spa with the gate valves closed!
Spa may be running in filtration mode. Press JETS or JETS 1 button to turn on high speed pump.
Power may be switched off. Turn the power back on.
The pump may be defective. After you have tried all other troubleshooting, contact your dealer for assistance.
Water level may be too low. Add water to normal level.
There may be a problem with circuit board. Contact your dealer.
The water level may be too low. Fill the spa with water level at 4 to 6 inches from the top.
Filter cartridge may be dirty. Clean or replace the filter.
Pump may have airlock. Remove airlock by priming spa (page 10)
The suction fittings may be blocked. Remove any debris that may be blocking the suction fittings.
Gate valves may be closed. Open gate valves. Note: Never operate your spa with the gate valves closed!
Air may be leaking into the suction line. Contact your dealer for assistance.
Debris may be inside the pump. Contact your dealer for assistance.
Noise may be a sign of damage. Contact your dealer for service.
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Symptom
Pump turns off during operation
Possible Solutions
Automatic timer may have completed its cycle. Press JETS or JETS 1 button to start the cycle again.
Pump may have overheated due to the vents on the equipment door being blocked. Make sure the front of the spa is not blocked to allow air flow.
The pump motor may be defective. Contact your dealer for assistance.
A burning smell may be a sign of damage. Contact your dealer for service.
Pump has a burning smell while running
Pump does not run Pump may have over heated. Let it cool for an hour and try operating the spa for a shorter time.
Power to the spa may be shut off. Turn on or reset the GFCI circuit breaker.
If this does not solve the problem, contact your dealer or a qualified spa technician.
“Thermal Creep”
Cal Spas are designed with energy-efficient components and systems that are meant to sustain heat generated by the equipment, which is then cycled back into the spa water. In hot weather or in situations where the spa is set to extended run times, Thermal
Creep may occur. Thermal Creep is a condition where the measured water temperature can be higher than the set temperature.
To manage Thermal Creep you may:
Vent your cover.
This means placing a folded cloth about ¾” (2cm) thick under all four corners of the cover before you lock the cover down.
Open your cover.
Opening the cover at night will also quickly cool the water down if desired.
Open all air controls.
Set your filtration cycles to run during the cooler times of the day or night.
Reduce the length of your filter cycles.
Visit your local dealer for additional guidance.
Since Thermal Creep only occurs in well-insulated hot tubs, it is not indicative of something that is wrong with your spa or its equipment.
49
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
50
Limited Warranty
This Limited Warranty is extended to the original purchaser of a Cal Spa brand portable spa manufactured after
January 1, 2020 and installed for residential use in the United States of America and Canada. This warranty begins on the date of delivery of the spa, but in no event later than one year from the date of manufacture.
This warranty applies only to this spa line:
Special Edition
Shell Structural
Warranted against water loss due to defects in the spa shell.
Shell Finish
Warranted against blistering, cracking, or delaminating of the interior surface of the spa shell.
Equipment and Controls
Electrical equipment components – specifically limited to the pumps, standard titanium heater, and control system – are warranted against malfunctions due to defects in workmanship or materials.
Plumbing
Warranted against leaks due to defects in workmanship or materials.
Cabinet - Synthetic or Fiberglass
Warranted against defects in workmanship or materials. Normal wear and weathering of the finish will occur naturally over time and are not defects.
5 years
2 years
2 years
1 year
1 year
Warranties for Other Components
The fuses, headrests, cabinet finish, and filters are warranted to be free of defects in workmanship and material at the time of delivery. All stereo-related components (receiver, speakers, sub-woofer, stereo media locker, power supply, wireless remote control etc.) are warranted against malfunction due to defects in workmanship or material for one year from the original date of delivery. All other factory-installed components not mentioned specifically, including, but not limited to the wood frame, jets, diverter valves, LED lighting systems, filter lids, and mechanical components, are warranted against malfunction due to defects in workmanship and material for two years from the original date of delivery. The spa cover delivered with the spa is warranted for 90 days.
Genuine Cal Spas Parts & Accessories
This Limited Warranty is void if Cal Spas (the “Manufacturer”) or its designated representative determines that the spa has been subjected to damage or failure due to installation of aftermarket parts that are not genuine Cal Spas branded parts and accessories. This disclaimer includes, but is not limited to filters, ozone systems, salt systems, repair parts and other accessories.
Genuine Cal Spas brand parts and accessories are built to our highest standards of quality, durability and performance, and they are designed to work with your spa to ensure optimal performance and function.
Performance
This warranty begins on the date of delivery of the spa, but in no event later than one year from the date of manufacture.
To obtain service in the event of a defect covered by this Limited Warranty, notify your Cal Spa dealer or Cal Spas as soon as possible and use all reasonable means to protect the spa from further damage. Upon proof of purchase, a designated service representative will correct the defect subject to the terms and conditions contained in this Limited Warranty. There will be no charge for parts or labor to repair the defect, although providing access to affect the repair is your responsibility as the spa owner. Freight charges for replacement parts is the responsibility of the spa owner. You may be assessed reasonable repairman travel mileage charges.
In the event that the spa is removed to a repair facility for repair and reinstalled, the cost of removal and reinstallation will be your responsibility as the spa owner. If the Manufacturer determines that repair of the covered defect is not feasible, it
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
Please visit www.quickspaparts.com to order your replacement parts.
reserves the right to provide a replacement spa instead. In such an event, reasonable costs for removal of the original spa, shipping costs from the factory for the replacement spa and delivery and installation of the replacement will be your responsibility as the spa owner. The replacement spa will carry the balance of the original spa’s warranty. Spa covers are not included.
This warranty ends either by specified time frame, ownertransfer, relocation, or installation of any component other than by manufacturer.
Warranty Limitations
This Limited Warranty is void if Cal Spas or its designated representative determines that the spa has been subjected to alteration, neglect, misuse or abuse, or freight damage caused by the common carrier; any repairs have been attempted by anyone other than a designated representative; the failure is caused by accident, acts of God or other causes beyond the control of the Manufacturer; neglect, misuse and abuse include any installation, operation or maintenance of the spa other than in accordance with the instructions contained in the owner’s manual provided with the spa, including but not limited to the failure to maintain proper water chemistry and chemical balance and the use of abrasive or improper cleaners or non-genuine parts and accessories. This Limited
Warranty does not provide coverage for any item attached to or installed on the spa after the date of manufacture or for gaining access to any component for repair or replacement.
Spa units in commercial use are excluded from any coverage whatsoever. The spa owner accepts liability for repair work performed by anyone other than the Manufacturer or a designated Cal Spa representative. This Limited Warranty is void if damage occurs to the spa shell because of excessive heat buildup due to failure to cover a spa that is empty of water while exposed to direct sunlight.
Proration of Warranty
Units determined by the Company to be non-repairable will be replaced on a prorated basis with the same or a comparable unit. The user will be charged one percent of the current retail cost for each full month of ownership from the date of purchase through the date failure is determined to be non-repairable. This charge will be waived during the first twelve months of ownership.
Disclaimers
The Manufacturer and its representatives shall not be liable for any injury, loss, cost or other damage, whether incidental or consequential, arising out of any defect covered by this limited warranty, including without limitation, loss of use of the spa and cost for removal of defective product even if the Manufacturer was advised of the possibility of damage.
The liability of the Manufacturer under this limited warranty, if any, shall not exceed the original amount paid for the defective product. Coverage under this limited warranty shall commence as of the original date of delivery and the duration of such coverage shall not extend for any reason whatsoever beyond the stated time periods. These disclaimers shall be equally applicable to any service provided by the Manufacturer and its designated representatives.
Legal Rights
This Limited Warranty gives you specific legal rights. You may also have other rights that vary from state to state.
Some states do not allow limitations on how long an implied warranty lasts, so this limitation may not apply to you.
Limitations
The Manufacturer disclaims all warranties, expressed or implied, in fact or in law, to the extent allowed by your
State’s Law, including the warranty of merchantability and fitness for use, except as stated specifically herein. All warranty service must be performed by the Manufacturer or its designated representative using authorized Cal Spa parts. No agent, dealer, distributor, service company or other party is authorized to change, modify or extend the terms of this limited warranty in any manner whatsoever.
The Manufacturer will not be responsible for any statements or representations made in any form that go beyond, are broader than, or are inconsistent with any authorized literature or specifications furnished by Cal Spas.
If you need jet bodies, go to www.quickspaparts.
com or refer to the Cal Spa Replacement
Parts Catalog, which can be downloaded from www.calspas.com/replacementparts.
51
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
52
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
53
54
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
55
56
www.calspas.com
2020 Portable Spas - LES
LTR20201163, Rev. Z3
2020 Portable Spas - LES
LTR20201163, Rev. Z3
www.calspas.com
57
58
Warranty Registration
Registering your new Cal Spas product is quick and easy. It is important that you register your Cal Spas product as soon as possible. By taking just a few quick minutes to register, you can enjoy product alerts, more efficient support, and quicker service.
Go to https://calspas.com/register-your-spa.php. Fill in your information and click “SEND WARRANTY INFO”
Locating the product serial number:
The serial number of your spa is located on a metal plate attached to the inside of the door for the equipment area. You will need this number to properly register your spa and activate coverage. Write this information in the space provided below.
Spa Model: ___________________________________________________________________________________
Spa Serial Number: ____________________________________________________________________________
Date Purchased: _______________________________________________________________________________
Date Installed: ________________________________________________________________________________
Dealer’s Phone Number: ________________________________________________________________________
Dealer’s Address: ______________________________________________________________________________
Please visit www.quickspaparts.com to order your replacement parts.
www.calspas.com
LTR20201163, Rev. Z3
6/26/20
2020 Portable Spas - LES
LTR20201163, Rev. Z3
advertisement
Related manuals
advertisement
Table of contents
- 3 Important Safety Instructions
- 4 Pre-Delivery Checklist
- 4 Planning the Best Location
- 5 Preparing a Good Foundation
- 5 Electrical Hookup
- 6 240 Volt Electrical Installation
- 7 Wiring Requirement
- 8 Canada
- 9 120 Volt Electrical Installation
- 9 Testing the 240 Volt GFCI Breaker
- 12 Priming the Pump
- 13 Operating Your Spa
- 13 One & Two-pump Systems
- 25 LED Lighting
- 26 Diverter Knobs
- 26 Air Venturis
- 26 Waterfalls
- 26 Hydro Streamer Waterfall
- 27 Water Clarity
- 27 Water Quality Terms and Definitions
- 28 Water Testing Methods
- 29 Adding Chemicals to the Spa Water
- 31 2. Sanitation and Shock
- 32 3. Filtration
- 33 4. Regularity (Maintenance Schedule)
- 33 Generic Names for Chemicals
- 34 Common Water Chemistry Questions
- 35 Do’s and Don’ts
- 36 Bather Load
- 36 Ozonator
- 37 Troubleshooting Water Clarity Problems
- 38 System
- 38 Removing and Reseating the Pillows
- 38 Jet Removal and Replacement
- 39 Draining Your Portable Spa
- 40 Winterizing (Cold Climate Draining)
- 40 Cleaning and Replacing the Filter
- 40 Installation
- 42 Vacation Care
- 42 Cleaning Your Spa
- 42 Using the Freedom Sound System
- 43 Appendix
- 43 Replacement Parts
- 49 Basic Troubleshooting
- 51 “Thermal Creep
- 52 Limited Warranty
- 60 Warranty Registration