- Computers & electronics
- Audio & home theatre
- Bluetooth music receivers
- Samsung
- HW-Q60T
- Owner's manual
advertisement
FULL MANUAL
HW-Q60T
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register your product at www.samsung.com/register
SAFETY INFORMATION
SAFETY WARNINGS
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Refer to the table below for an explanation of symbols which may be on your Samsung product.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION
• TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
• This apparatus shall always be connected to a
AC outlet with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.
• Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases on the apparatus.
• To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.
This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.
This symbol indicates that this product has included important literature concerning operation and maintenance.
Class II product : This symbol indicates that it does not require a safety connection to electrical earth (ground).
If this symbol is not present on a product with a power cord, the product
MUST have a reliable connection to protective earth (ground).
AC voltage : This symbol indicates that the rated voltage marked with the symbol is AC voltage.
DC voltage : This symbol indicates that the rated voltage marked with the symbol is DC voltage.
Caution, Consult instructions for use :
This symbol instructs the user to consult the user manual for further safety related information.
ENG - ii
PRECAUTIONS
1.
Ensure that the AC power supply in your house complies with the power requirements listed on the identification sticker located on the bottom of your product. Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation (7~10 cm).
Make sure the ventilation slots are not covered. Do not place the unit on amplifiers or other equipment which may become hot.
This unit is designed for continuous use. To fully turn off the unit, disconnect the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.
2.
During thunderstorms, disconnect the AC plug from the wall outlet. Voltage peaks due to lightning could damage the unit.
3.
Do not expose the unit to direct sunlight or other heat sources. This could lead to overheating and cause the unit to malfunction.
4.
Protect the product from moisture (i.e. vases), and excess heat (e.g. a fireplace) or equipment creating strong magnetic or electric fields. Unplug the power cable from the AC wall socket if the unit malfunctions.
Your product is not intended for industrial use. It is for personal use only. Condensation may occur if your product has been stored in cold temperatures. If transporting the unit during the winter, wait approximately
2 hours until the unit has reached room temperature before using.
5.
The battery used with this product contains chemicals that are harmful to the environment. Do not dispose of the battery in the general household trash. Do not expose the battery to excess heat, direct sunlight, or fire. Do not short circuit, disassemble, or overheat the battery.
Danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type.
ABOUT THIS MANUAL
The user manual has two parts: this simple paper
USER MANUAL and a detailed FULL MANUAL you can download.
USER MANUAL
See this manual for safety instructions, product installation, components, connections, and product specifications.
FULL MANUAL
You can access the FULL MANUAL on
Samsung’s on-line customer support centre by scanning the QR code. To see the manual on your PC or mobile device, download the manual in document format from Samsung’s website. (http://www.samsung.com/support)
Design and specifications are subject to change without prior notice.
ENG - iii
CONTENTS
01 Checking the Components 2
Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 2
02 Product Overview
Front Panel / Top Panel of the Soundbar
3
03 Connecting the Soundbar 5
Connecting the Soundbar to the Subwoofer
– Automatic connection between the Subwoofer and the Soundbar
– Manually connecting the Subwoofer if automatic connection fails
Connecting an SWA-8500S (Sold Separately) to your Soundbar
04
05
Connecting to your TV
Method 1. Connecting with a Cable
– Connecting a TV using an HDMI Cable
– Connecting using an Optical Cable
Method 2. Connecting Wirelessly
– Connecting a TV via Bluetooth
Connecting an External Device
Connecting using an HDMI Cable
Connecting using an Optical Cable
10
15
06 Connecting a USB Storage Device 17
ENG - iv
07 Connecting a Mobile Device
08 Using the Remote Control
Adjusting the Soundbar volume with a TV remote control
Using the Hidden Buttons (Buttons with more than one function)
Output specifications for the different sound effect modes
09 Installing the Wall Mount
10 Placing the Soundbar on a TV stand
11 Software Update
12 Troubleshooting
13 Licence
14 Open Source Licence Notice
15 Important Notes About Service
16 Specifications and Guide
18
22
27
29
30
32
33
33
33
34
ENG - v
01 CHECKING THE COMPONENTS
PAIR
VOL WOOFER
SOUNDBAR
Soundbar Main Unit Subwoofer Remote Control / Batteries
x 2
Power Cord
(Subwoofer, Soundbar)
AC/DC Adapter
(Soundbar)
HDMI Cable
x 2 x 2 x 2
Screw
Wall Mount Guide
Holder-Screw Bracket-Wall Mount
• For more information about the power supply and power consumption, refer to the label attached to the product. (Label: Bottom of the Soundbar Main Unit)
• To purchase additional components or optional cables, contact a Samsung Service Centre or
Samsung Customer Care.
• The appearance of the accessories may differ slightly from the illustrations above.
Inserting Batteries before using the Remote Control (AA batteries X 2)
Slide the back cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries
(1.5V) oriented so that their polarity is correct. Slide the back cover back into position.
ENG - 2
02 PRODUCT OVERVIEW
Front Panel / Top Panel of the Soundbar
Position the product so that the SAMSUNG logo is located on the top.
Top Panel
Display
Displays the product’s status and current mode.
(Power) Button
Turns the power on and off.
•
Auto Power Down Function
The unit turns off automatically in the following situations:
– In
D.IN
/
HDMI
/
BT
/
USB
Mode : If there is no audio signal for 20 minutes.
-/+ (Volume) Button
Adjusts the volume.
• When adjusted, the volume level appears on the Soundbar’s front display.
(
Source) Button
Selects the source input mode.
Input mode
Optical Digital input
ARC (HDMI OUT) input
HDMI input
BLUETOOTH mode
USB mode
Display
D.IN
D.IN
TV ARC (Auto conversion)
HDMI
BT
USB
• To turn on
“BT PAIRING
” mode, change the source to “
BT
” mode, and then press and hold the
(Source)
button for more than 5 seconds.
• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.
• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.
• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio
Setup menu of your TV. Refer to the owner’s manual supplied with your TV.
ENG - 3
Bottom Panel of the Soundbar
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
Connect a USB device here to play music files stored on the USB device through the Soundbar.
DC 24V (Power Supply In)
Connect the AC/DC power adapter.
HDMI
Inputs digital video and audio signals simultaneously using an HDMI cable.
Connect to the HDMI output of an external device.
HDMI TO TV (ARC)
Connect to the HDMI (ARC) jack on a TV.
DIGITAL AUDIO IN (OPTICAL)
Connect to the digital (optical) output of an external device.
• When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug.
Do not pull the cable.
• Do not connect this unit or other components to an AC outlet until all connections between components are complete.
ENG - 4
03 CONNECTING THE SOUNDBAR
Connecting Electrical Power
Use the power components to connect the Subwoofer and Soundbar to an electrical outlet in the following order:
1.
Connect the power cord to the Subwoofer.
2.
Connect the power output cable to the power adapter, and then to the Soundbar.
3.
Connect the power cord to a wall socket.
See the illustrations below.
• For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label: Bottom of the Soundbar Main Unit)
Power Cord
DC 24V
POWER
Power Cord
Connecting
Electrical Power
AC/DC Adapter
USB (5V 0.5A)
DC 24V
Bottom of the
Soundbar Main Unit
Rear of Subwoofer
Connecting
Electrical Power
• Make sure to rest the AC/DC Adapter flat on a table or the floor. If you place the AC/DC Adapter so that it is hanging with the AC cord input facing upwards, water or other foreign substances could enter the Adapter and cause the Adapter to malfunction.
ENG - 5
Connecting the Soundbar to the Subwoofer
When the subwoofer is connected, you can enjoy rich bass sound.
Automatic connection between the Subwoofer and the Soundbar
When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the subwoofer is automatically connected to the Soundbar.
• When auto pairing is complete, the blue indicators at the rear of the subwoofer turn on.
LED Indicator Lights on the Rear of Subwoofer
LED
Blue
Red
Red and blue
Status
On
Description
Successfully connected
(normal operation)
-
Resolution
Blinking
On
Blinking
Recovering the connection
Standby (with the Soundbar main unit turned off)
Connection failed
Malfunction
Check if the power cable attached to the main Soundbar unit is connected properly or wait about 5 minutes. If blinking persists, try manually connecting the subwoofer.
Check if the power cable attached to the main Soundbar unit is connected properly.
Connect again. See the instructions for
See the contact information for the
Samsung Service Centre in this manual.
ENG - 6
Manually connecting the Subwoofer if automatic connection fails
Before performing the manual connection procedure below:
• Check whether the power cables for the Soundbar and subwoofer are connected properly.
• Make sure that the Soundbar is turned on.
1.
Press and hold
ID SET
on the rear of the subwoofer for at least 5 seconds.
• The red indicator on the rear of the subwoofer turns off and the blue indicator blinks.
5 Sec
Rear of Subwoofer
2.
Press and hold the
Up
button on the remote control for at least 5 seconds.
• The
ID SET
message appears on the display of the Soundbar for a moment, and then it disappears.
• The Soundbar will automatically power on when
ID SET
is complete.
PAIR
5 Sec
SAMSUNG logo is on the top
ID SET
SOUN
D
MOD
E
3.
Check if the LINK LED is solid blue (connection complete).
The LINK LED indicator stops blinking and glows a solid blue when a connection is established between the Soundbar and the
Wireless Subwoofer.
Blue is On
ENG - 7
NOTES
• Do not connect the power cord of this product or your TV to a wall outlet until all connections between components are complete.
• Before moving or installing this product, be sure to turn off the power and disconnect the power cord.
• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the
STANDBY LED on the rear of the sub-woofer will turn red after blinking in blue several times.
• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar, interference may cause some sound interruption.
• The maximum transmission distance of the main unit’s wireless signal is about 10 meters, but may vary depending on your operating environment. If a steel-concrete or metallic wall is between the main unit and the wireless subwoofer, the system may not operate at all because the wireless signal cannot penetrate metal.
PRECAUTIONS
• Wireless receiving antennas are built into the wireless subwoofer. Keep the unit away from water and moisture.
• For optimal listening performance, make sure that the area around the wireless subwoofer and the
Wireless Receiver Module (sold separately) is clear of any obstructions.
Connecting an SWA-8500S (Sold Separately) to your Soundbar
Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit
(SWA-8500S, sold separately) to your Soundbar.
1.
Connect the Wireless Receiver Module to 2 Surround Speakers.
– The speaker cables are colour coded.
SURROUND-LEFT
SURROUND-LEFT
L
L R
ID SET
R
SURROUND SPEAKERS OUT
ID SET
SURROUND-RIGHT
SURROUND-RIGHT
ENG - 8
2.
Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.
• The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not blink, press the
ID SET
button on the back of the Wireless Receiver Module with a pen tip for
5~6 seconds until the LINK LED indicator blinks (in Blue). For more about the LED, please refer to the SWA-8500S user manual.
SURROUND SPEAKERS OUT
R
5 Sec
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
ID SET
ID SET
STANDBY
LINK
STANDBY
LINK
POWER
Blue blinking
POWER
3.
Press and hold the
Up
button on the remote control for at least 5 seconds.
• The
ID SET
message appears on the display of the Soundbar for a moment, and then it disappears.
• The Soundbar will automatically power on when
ID SET
is complete.
PAIR
5 Sec
SAMSUNG logo is on the top
ID SET
SOUN
D
MOD
E
CAUTION
• If your Soundbar was playing music when it connects to the SWA-8500S, you may hear some stuttering from the woofer as the connection finalises.
4.
Check if the LINK LED is solid blue (connection complete).
STANDBY
STANDBY
LINK
LINK
The LINK LED indicator stops blinking and glows a solid blue when a connection is established between the Soundbar and the
Wireless Receiver Module.
Blue is On
5.
If the SWA-8500S is not connected, repeat the procedure from Step 2.
ENG - 9
04 CONNECTING TO YOUR TV
Hear TV sound from your Soundbar through wired or wireless connections.
• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using the TV’s remote control.
– This feature is supported by 2017 and later Samsung Smart TVs that support Bluetooth when you connect the Soundbar to the TV using an optical cable.
– This function also allows you to use the TV menu to adjust the sound field and various settings as well as the volume and mute.
Method 1. Connecting with a Cable
When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on the TV is changed, you will experience better sound quality. (The TV menu may use different words for
Dolby Digital and PCM depending on the TV manufacturer.)
Connecting a TV using an HDMI Cable
Connect to the HDMI IN
(ARC) port of your TV.
HDMI Cable
Bottom of the Soundbar
HDMI IN
(ARC)
Connect to the HDMI TO TV (ARC) port of the Soundbar main unit.
Top of the Soundbar
TV ARC
1.
With the Soundbar and TV turned on, connect the HDMI cable as shown in the figure.
2.
“
TV ARC
” appears in the display window of the Soundbar main unit and the Soundbar plays TV sound.
ENG - 10
• If TV sound is inaudible, press the
(Source)
button on the remote control or on the top of the Soundbar to switch to “
D.IN
” mode. The screen displays “
D.IN
” and “
TV ARC
” in sequence, and TV sound is played.
• If “
TV ARC
” does not appear in the display window of the Soundbar main unit, confirm that the
HDMI cable is connected to the correct port.
• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.
NOTES
• HDMI is an interface that enables the digital transmission of video and audio data with just a single connector.
• If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.
• We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one whose diameter is less than 14 mm.
• This function is not available if the HDMI cable does not support ARC.
Connecting using an Optical Cable
Bottom of the Soundbar
DIGITAL AUDIO IN (OPTICAL)
Optical Cable
(not supplied)
Top of the Soundbar
OPTICAL OUT
D.IN
1.
Connect the
DIGITAL AUDIO IN (OPTICAL)
jack on the Soundbar to the OPTICAL OUT jack of the TV with a digital Optical Cable (not supplied).
2.
Press the
(Source)
button on the top panel or remote control, and then select the “
D.IN
” mode.
ENG - 11
Using the Q-Symphony Function
For Q-Symphony, the Soundbar syncs with a Samsung TV to output sound through two devices for optimum surround effect. When the Soundbar is connected, the menu, “
TV+Soundbar
” appears under the
Sound Output
menu of the TV. Select the corresponding menu.
TV Menu
HDMI Cable
OR
D.IN
Optical Cable (not supplied)
• TV menu example:
TV series name + [AV] Soundbar series name (HDMI)
NOTES
• It can operate according to the Codec supported by TV.
• This function is supported only when the HDMI Cable or Optical Cable (not supplied) is connected.
• This function is available in Samsung TVs released in 2020 and some Soundbar models.
ENG - 12
Method 2. Connecting Wirelessly
Connecting a TV via Bluetooth
When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.
• Only one TV can be connected at a time.
PAIR
OR
D
MOD
E
The initial connection
1.
Press the
PAIR
button on the remote control to enter the “
BT PAIRING
” mode.
(OR)
a.
Press the
(Source)
button on the top panel and then select “
BT
”.
“
BT
” changes to “
BT PAIRING
” in a few seconds automatically or changes to “
BT READY
” if there is a connect record.
b.
When “
BT READY
” appears, press and hold the
(Source)
button on the top panel of the
Soundbar for more than 5 seconds to display “
BT PAIRING
”.
2.
Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)
3.
Select “
[AV] Samsung Soundbar Q6T-Series
” from the list on TV’s screen.
An available Soundbar is indicated with “
Need Pairing
” or “
Paired
” on the TV’s Bluetooth device list. To connect the TV to the Soundbar, select the message, and then establish a connection.
• When the TV is connected, [
TV Name
] → “
BT
” appears on the Soundbar’s front display.
4.
You can now hear TV sound from the Soundbar.
If the device fails to connect
• If a previously connected Soundbar listing (e.g. “
[AV] Samsung Soundbar Q6T-Series
”) appears in the list, delete it.
• Then repeat steps 1 through 3.
NOTE
• After you have connected the Soundbar to your TV the first time, use the “
BT READY
” mode to reconnect.
ENG - 13
Disconnecting the Soundbar from the TV
Press the
(Source)
button on the top panel or on the remote control and switch to any mode but “
BT
”.
• Disconnecting takes time because the TV must receive a response from the Soundbar.
(The time required may differ, depending on the TV model.)
• To cancel the automatic Bluetooth connection between the Soundbar and TV, press the
Left
button on the remote control for 5 seconds with the Soundbar in “
BT READY
” status. (Toggle On → Off)
What is the difference between BT READY and BT PAIRING?
•
BT READY
: In this mode, you can search for previously connected TVs or connect a previously connected mobile device to the Soundbar.
•
BT PAIRING
: In this mode, you can connect a new device to the Soundbar. (Press the
PAIR
button on the remote control or press and hold the
(Source)
button on the top of the Soundbar for more than 5 seconds while the Soundbar is in “
BT
” mode.)
NOTES
• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
• The Soundbar automatically turns off after 20 minutes in the Ready state.
• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances:
– If there is a strong electrical field around the Soundbar.
– If two or more Bluetooth devices are simultaneously paired with the Soundbar.
– If the Bluetooth device is turned off, not in place, or malfunctions.
• Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
ENG - 14
05 CONNECTING AN EXTERNAL DEVICE
Connect to an external device via a wired connection or Bluetooth connection to play the external device’s sound through the Soundbar.
Connecting using an HDMI Cable
Bottom of the Soundbar
HDMI OUT
HDMI
External Device
HDMI Cable
HDMI IN
(ARC)
HDMI Cable
Top of the Soundbar
HDMI
1.
Connect an HDMI cable from the
HDMI
jack on the back of the product to the HDMI OUT jack on your digital device.
2.
Connect an HDMI cable from the
HDMI TO TV (ARC)
jack on the back of the product to the HDMI IN jack on your TV.
3.
Press the
(Source)
button on the top panel or on the remote control, and then select “
HDMI
”.
4.
“
HDMI
” mode is displayed on the Soundbar display panel and sound plays.
ENG - 15
Connecting using an Optical Cable
Bottom of the Soundbar
Optical Cable
(not supplied)
DIGITAL AUDIO IN (OPTICAL)
OPTICAL OUT
Top of the Soundbar
BD / DVD player /
Set-top box /
Game console
D.IN
1.
Connect
DIGITAL AUDIO IN (OPTICAL)
on the main unit to the OPTICAL OUT jack of the Source
Device using a digital Optical Cable (not supplied).
2.
Select “
D.IN
” mode by pressing the
(Source)
button on the top panel or on the remote control.
ENG - 16
06 CONNECTING A USB STORAGE DEVICE
You can play music files located on USB storage devices through the Soundbar.
USB (5V 0.5A)
DC 24V
USB port
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
USB
1.
Connect the USB device to the USB port on the bottom of the product.
2.
Press the
(Source)
button on the top panel or on the remote control, and then select “
USB
”.
3.
“
USB
” appears in the display screen.
4.
Play music files from the USB storage device through the Soundbar.
• The Soundbar automatically turns off (Auto Power Down) if no USB device has been connected for more than 20 minutes.
File Format Type Compatibility list
Extension
*.mp3
Codec
MPEG1 Layer2
MPEG1 Layer3
MPEG2 Layer3
MPEG2.5 Layer3
WMA7/8/9 (Audio Only)
Vorbis
Sampling Rate
32kHz ~ 48kHz
32kHz ~ 48kHz
16kHz ~ 24kHz
8kHz ~ 12kHz
32kHz ~ 48kHz
32kHz ~ 48kHz
Bit rate
32kbps ~ 320kbps
32kbps ~ 320kbps
8kbps ~ 160kbps
8kbps ~ 160kbps
32kbps ~ 320kbps
45kbps ~ 500kbps
*.wma
*.ogg
*.aac
*.m4a
*.mp4
*.wav
*.flac
*.aiff
AAC-LC
(MPEG2/MPEG4 Audio Only)
32kHz ~ 48kHz 32kbps ~ 320kbps
LPCM
FLAC
AIFF
32kHz ~ 192kHz
32kHz ~ 192kHz
32kHz ~ 192kHz
1,024kbps ~ 9,216kbps
162kbps ~ 8,100kbps
1,024kbps ~ 9,216kbps
• If there are too many folders and files stored on the USB device, it may take the Soundbar some time to access and play files.
ENG - 17
07 CONNECTING A MOBILE DEVICE
Connecting via Bluetooth
When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.
• The connection is limited to one TV or two Bluetooth devices at the same time.
PAIR
OR
Bluetooth device
D
MOD
E
The initial connection
1.
Press the
PAIR
button on the remote control to enter the “
BT PAIRING
” mode.
(OR)
a.
Press the
(Source)
button on the top panel and then select “
BT
”.
“
BT
” changes to “
BT PAIRING
” in a few seconds automatically or changes to “
BT READY
” if there is a connect record.
b.
When “
BT READY
” appears, press and hold the
(Source)
button on the top panel of the
Soundbar for more than 5 seconds to display “
BT PAIRING
”.
2.
On your device, select “
[AV] Samsung Soundbar Q6T-Series
” from the list that appears.
• When the Soundbar is connected to the Bluetooth device, [
Bluetooth Device Name
] → “
BT
” appears in the front display.
3.
Play music files from the device connected via Bluetooth through the Soundbar.
If the device fails to connect
• If a previously connected Soundbar listing (e.g. “
[AV] Samsung Soundbar Q6T-Series
”) appears in the list, delete it.
• Then repeat steps 1 and 2.
NOTE
• After you have connected the Soundbar to your mobile device the first time, use the “
BT READY
” mode to reconnect.
ENG - 18
What is the difference between BT READY and BT PAIRING?
•
BT READY
: In this mode, you can search for previously connected TVs or connect a previously connected mobile device to the Soundbar.
•
BT PAIRING
: In this mode, you can connect a new device to the Soundbar. (Press the
PAIR
button on the remote control or press and hold the
(Source)
button on the top of the Soundbar for more than 5 seconds while the Soundbar is in “
BT
” mode.)
NOTES
• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
• The Soundbar automatically turns off after 20 minutes in the Ready state.
• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances:
– If there is a strong electrical field around the Soundbar.
– If several Bluetooth devices are simultaneously paired with the Soundbar.
– If the Bluetooth device is turned off, not in place, or malfunctions.
• Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
• The Soundbar supports SBC data (44.1kHz, 48kHz).
• Connect only to a Bluetooth device that supports the A2DP (AV) function.
• You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free) function.
• Once you have paired the Soundbar to a Bluetooth device, selecting “
[AV] Samsung Soundbar
Q6T-Series
” from the device’s scanned devices list will automatically change the Soundbar to “
BT
” mode.
– Available only if the Soundbar is listed among the Bluetooth device’s paired devices.
(The Bluetooth device and the Soundbar must have been previously paired at least once.)
• The Soundbar will appear in the Bluetooth device’s searched devices list only when the Soundbar is displaying “
BT READY
”.
Bluetooth Power On (SOUND MODE)
If a previously paired Bluetooth device tries to pair with the Soundbar when the Bluetooth Power On function is on and the Soundbar is turned off, the Soundbar turns on automatically.
1.
Press and hold the
SOUND MODE
button for more than 5 seconds on the remote while the
Soundbar is turned on.
2.
“
ON-BLUETOOTH POWER
” appears on the Soundbar’s display.
ENG - 19
Disconnecting the Bluetooth device from a Soundbar
You can disconnect a Bluetooth device from the Soundbar. For instructions, see the Bluetooth device’s user manual.
• The Soundbar will be disconnected.
• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display
“
BT DISCONNECTED
” on the front display.
Disconnecting the Soundbar from the Bluetooth device
Press the
(Source)
button on the top panel or on the remote control, and then change to any mode except “
BT
”.
• Disconnecting takes time because the Bluetooth device must receive a response from the
Soundbar. (Disconnection time may differ, depending on the Bluetooth device)
• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display
“
BT DISCONNECTED
” on the front display.
NOTES
• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
• The Soundbar automatically turns off after 20 minutes in the Ready state.
More About Bluetooth
Bluetooth is a technology that enables Bluetooth-compliant devices to interconnect easily with each other using a short wireless connection.
• A Bluetooth device may cause noise or malfunction, depending on usage, if:
– A part of your body is in contact with the receiving/transmitting system of the Bluetooth device or the Soundbar.
– It is subject to electrical variation from obstructions caused by a wall, corner, or office partition.
– It is exposed to electrical interference from same frequency-band devices including medical equipment, microwave ovens, and wireless LANs.
• Pair the Soundbar with the Bluetooth device while they are close together.
• The further the distance between the Soundbar and Bluetooth device, the worse the quality is.
If the distance exceeds the Bluetooth operational range, the connection is lost.
• In poor reception areas, the Bluetooth connection may not work properly.
• The Bluetooth connection only works when it is close to the unit. The connection will be automatically cut off if the Bluetooth device is out of range. Even within range, the sound quality may be degraded by obstacles such as walls or doors.
• This wireless device may cause electric interference during its operation.
ENG - 20
Bluetooth Multi connection
The Soundbar can be connected to 2 Bluetooth devices at the same time.
Bluetooth device A Bluetooth device B
1.
Connect the Soundbar to up to two Bluetooth devices. (See page 18)
2.
Play music from one of the connected Bluetooth devices while two devices are connected.
3.
To play music from the Bluetooth device “B” while playing from the device “A”, pause or stop playback on the device “A” and then start playing on the device “B”.
• The device won’t switch if playing music from the device “B” without pausing or stopping the device “A” first.
4.
In versions prior to AVRCP V1.4, the switching time of the device playing music may be delayed.
NOTES
• If you attempt to connect a 3rd Bluetooth device, the A or B devices will disconnect.
(A device that is not currently playing will be disconnected.)
• Only one Samsung TV, or 2 Bluetooth devices can be connected at the same time.
• The Soundbar will be disconnected from Bluetooth devices when it receives a connection request from a Samsung TV.
ENG - 21
08 USING THE REMOTE CONTROL
How to Use the Remote Control
SOUND
MODE
PAIR
VOL WOOFER
SOUNDBAR
Turns the Soundbar on and off.
Power
Press to select a source connected to the
Soundbar.
Source
Press the
(Mute)
button to mute the sound.
VOL
Mute
PAIR
SOUND
MODE
SOUND MODE
SOUND
You can select the desired sound effect by choosing
STANDARD
,
SURROUND SOUND
,
GAME
PRO
,
ADAPTIVE SOUND
, or
DTS VIRTUAL:X
.
–
STANDARD
Outputs the original sound.
SOUND
MODE
VOL
PAIR
–
SURROUND SOUND
Provides a wider sound field than standard.
VOL
–
GAME PRO
WOOFER
MODE
Provides stereoscopic sound to immerse you in the action while gaming.
WOOFER
VOL
–
ADAPTIVE SOUND
Analyzes the content in real time and automatically provides the optimal sound field based on the characteristics of the content.
–
DTS VIRTUAL:X
Immersive 3D sound from any content.
ENG - 22
PAIR
SOUND
MODE
Bluetooth
PAIR
•
DRC (Dynamic Range Control)
Lets you apply dynamic range control to Dolby Digital tracks. Press and hold the
SOUND MODE
button while the Soundbar is powered off to turn DRC (Dynamic Range
Control) on or off. With the DRC turned on, loud sound is reduced. (The sound may be distorted.)
•
Bluetooth Power
This feature automatically turns the Soundbar on when it receives a connection request from a previously connected TV or Bluetooth device. The setting is On by default.
– Press and hold the
SOUND MODE
button for more than 5 seconds to turn off the
Bluetooth Power function.
Press the
PAIR
button. “
BT PAIRING
” appears in the Soundbar’s display.
You can connect the Soundbar to a new Bluetooth device in this mode by selecting the
Soundbar from the Bluetooth device's search list.
Press the
p
button to pause a music file temporarily.
When you press the button again, the music file plays.
Play / Pause
VOL WOOFER
PAIR
Press the indicated areas to select Up/Down/Left/Right.
SOUND
MODE
PAIR
Left/Right
VOL
VOL WOOFER
WOOFER
Press Up/Down/Left/Right on the button to select or set functions.
•
Repeat
To use the Repeat function in “
USB
” mode, press the
Up
button.
•
Music Skip
Press the
Right
button to select the next music file. Press the
Left
button to select the previous music file.
•
ID SET
Press and hold the
Up
button for 5 seconds to complete
ID SET
(when connecting to an accessary item).
ENG - 23
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
VOL
Sound Control
SOUND
MODE
SOU
ND
MO
DE
VOL
PAIR
•
Volume Restriction function
To protect your hearing, the Volume Restriction function restricts the volume to 20 if you turn on the Soundbar when the volume is set higher than 20.
– The default value for the Volume Restriction function is Off. You must turn it on to activate it.
– When turned on, the Volume Restriction function stays on even when the power is turned off.
– To turn Volume Restriction on or off, press and hold the
Down
button on the remote control for 5 seconds. With Volume Restriction off, “
V FREE
” appears on the front display. With the function on, “
V LOCK
” appears.
You can select
TREBLE
,
BASS
, or
AUDIO SYNC
• To control the volume of the treble or bass sound, press the
Sound Control
button to select
TREBLE
or
BASS
and then adjust the volume between -6~+6 by using the
Up/
Down
buttons.
• Press and hold the
(Sound Control)
button for about 5 seconds to adjust the sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and 10kHz are selectable using the
Left/Right
buttons and each can be adjusted to a setting between
-6 to +6 using the
Up/Down
buttons.
• If the video on the TV and audio from the Soundbar are not synchronised, press the
Sound Control
button to select
AUDIO SYNC
and then set the audio delay between
0~300 milliseconds by using the
Up/Down
buttons. (Not available in “
USB
” or “
BT
” mode.)
• If Surround Speakers are connected, the Rear Speaker function can be turned ON/OFF by using the
Up/Down
buttons to adjust the volume within a -6 to +6 range.
•
AUDIO SYNC
is only supported for some functions.
PAIR
PAIR
R
WOOFE
MODE
SOUND
MODE
SOUNDB
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Rock the
WOOFER
button forward or backward to adjust the volume of the subwoofer to
-12 or between -6 to +6. To set the subwoofer volume level to 0, press the button in.
VOL
VOL
WOOFER
SOU
ND
MO
DE
WOOFER
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Rock the
VOL
button forward or backward to adjust the volume.
•
Mute
Press the
VOL
button in to mute the sound. Press it in again to unmute the sound.
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
ENG - 24
Adjusting the Soundbar volume with a TV remote control
If you have a Samsung TV, you can adjust the Soundbar’s volume using the IR remote control that came with your Samsung TV.
First use the TV menu to set the TV audio on your
Samsung TV to external speakers, then use your
Samsung remote to control the Soundbar’s volume. For more information, see the TV’s user manual. The default mode for this function is control by a Samsung TV remote. If your TV is not a Samsung TV, follow the directions below to change the settings of this function.
1.
Turn Off the Soundbar.
BYE
4.
If you want to return the Soundbar to the default mode (control by a Samsung TV remote), push up and hold the
WOOFER
button for 5 seconds repeatedly until
“
SAMSUNG-TV REMOTE
” appears in the display.
SOU
ND
MO
DE
5 Sec
(Default mode)
SAMSUNG-TV REMOTE
VOL
WOOFE
R
SOUNDB
AR
– Each time you push the
WOOFER
button up and hold it for 5 seconds, the mode switches in the following order:
“
SAMSUNG-TV REMOTE
” (Default mode)
→ “
OFF‑TV REMOTE
” → “
ALL‑TV REMOTE
”.
– This function may not be available, depending on the remote control.
– Manufacturers supporting this function:
VIZIO, LG, Sony, Sharp, PHILIPS,
PANASONIC, TOSHIBA, Hisense, RCA
2.
If you do not want to use this function, push up and hold the
WOOFER
button for
5 seconds repeatedly until “
OFF-TV
REMOTE
” appears in the display.
SOU
ND
MO
DE
5 Sec OFF-TV REMOTE
VOL
WOOFE
R
SOUNDB
AR
3.
If you want to control the Soundbar with your TV’s remote, push up and hold the
WOOFER
button for 5 seconds repeatedly until “
ALL-TV REMOTE
” appears in the display. Then, use your TV’s menu to select external speakers.
5 Sec
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
ALL-TV REMOTE
ENG - 25
Using the Hidden Buttons (Buttons with more than one function)
Remote Control Button
WOOFER (Up)
p
(Play / Pause)
Left
Up
Down
(Sound Control)
SOUND MODE
Hidden Button
Function
TV remote control On/Off (Standby)
Initialise (Standby)
TV Auto connect On/Off (BT Ready)
ID SET (Standby)
Volume Restriction On/Off (Standby)
7 Band EQ
DRC ON/OFF (Standby)
Bluetooth Power
Reference page
Output specifications for the different sound effect modes
Surround
VOL
SOUND
MODE
Effect
STANDARD
Bluetooth
POWER
SURROUND
SOUND
SOUND MODE
GAME PRO
ADAPTIVE
SOUND
WOOFER
DTS VIRTUAL:X
Input
2.0 ch
5.1 ch
2.0 ch
5.1 ch
2.0 ch
5.1 ch
2.0 ch
5.1 ch
2.0 ch
5.1 ch
Without Wireless Rear
Speaker Kit
2.1 ch
3.1 ch
4.1 ch
5.1 ch
4.1 ch
5.1 ch
4.1 ch
5.1 ch
3.1 ch
3.1 ch
Output
With Wireless Rear
Speaker Kit
4.1 ch
5.1 ch
6.1 ch
7.1 ch
6.1 ch
7.1 ch
6.1 ch
7.1 ch
5.1 ch
5.1 ch
• The Samsung Wireless Rear Speaker Kit can be purchased separately. To purchase a Kit, contact the vendor you purchased the Soundbar from.
ENG - 26
09 INSTALLING THE
WALL MOUNT
Wallmount Components
Wall Mount Guide
Installation Precautions
• Install on a vertical wall only.
• Do not install in a place with high temperature or humidity.
• Verify whether the wall is strong enough to support the product’s weight. If not, reinforce the wall or choose another installation point.
• Purchase and use the fixing screws or anchors appropriate for the kind of wall you have (plaster board, iron board, wood, etc.). If possible, fix the support screws into wall studs.
• Purchase wall mounting screws according to the type and thickness of the wall you want to mount the Soundbar on.
– Diameter: M5
– Length: 35 mm or longer recommended.
• Connect cables from the unit to external devices before you install the Soundbar on the wall.
• Make sure the unit is turned off and unplugged before you install it. Otherwise, it may cause an electric shock.
x 2
Holder-Screw
x 2
Bracket-Wall Mount
x 2
Screw
1.
Place the
Wall Mount Guide
against the wall surface.
• The
Wall Mount Guide
must be level.
• If your TV is mounted on the wall, install the Soundbar at least 5 cm below the TV.
5 cm or more
ENG - 27
2.
Align the
Wall Mount Guide’s Centre Line
with the centre of your TV (if you are mounting the Soundbar below your TV), and then fix the
Wall Mount Guide
to the wall using tape.
• If you are not mounting below a TV, place the
Centre Line
in the centre of the installation area.
5.
Push a screw (not supplied) through each
Holder-Screw
, and then screw each screw firmly into a support screw hole.
6.
Install the 2
Bracket-Wall Mounts
in the correct orientation on the bottom of the
Soundbar using 2
Screws
.
Centre Line
3.
Push a pen tip or sharpened pencil tip through the centre of the
A-TYPE
images on each end of the Guide to mark the holes for the supporting screws, and then remove the
Wall Mount Guide
.
4.
Using an appropriately sized drill bit, drill a hole in the wall at each marking.
• If the markings do not correspond to the positions of studs, make sure you insert appropriate anchors or mollies into the holes before you insert the support screws. If you use anchors or mollies, make sure the holes you drill are large enough for the anchors or mollies you use.
• When assembling, make sure the hanger part of the
Bracket-Wall Mounts
are located behind the rear of the Soundbar.
Rear of Soundbar
Right end of Soundbar
ENG - 28
7.
Install the Soundbar with the attached
Bracket-Wall Mounts
by hanging the
Bracket-Wall Mounts
on the
Holder-Screws
on the wall.
10 PLACING THE
SOUNDBAR ON A
TV STAND
Place the Soundbar on a TV stand.
8.
Slide the Soundbar down as shown below so that the
Bracket-Wall Mounts
rest securely on the
Holder-Screws
.
• Insert the
Holder-Screws
into the wide
(bottom) part of the
Bracket-Wall
Mounts
, and then slide the
Bracket-Wall
Mounts
down so that the
Bracket-Wall
Mounts
rest securely on the
Holder-Screws
.
3cm o r more
As illustrated in the image, align the centre of the
Soundbar with the centre of the TV, carefully place the Soundbar onto the TV stand.
For optimal sound quality, position the Soundbar at least 3 cm away from the TV front.
NOTE
• Make sure the Soundbar is placed on a flat and solid surface.
ENG - 29
11 SOFTWARE
UPDATE
Samsung may offer updates for the Soundbar’s system firmware in the future.
USB port
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
If an update is offered, you can update the firmware by connecting a USB device with the firmware update stored on it to the USB port on your Soundbar. For more information about how to download update files, go to the Samsung website at www.samsung.com
Support.
Then, select the product type or enter the model number of your Soundbar, select the Software &
Apps option, and then Downloads. Note that the option names can vary.
Update Procedure
Important:
The updating function erases all user settings. We recommend you write down your settings so that you can easily reset them after the update. Note that updating the firmware resets the subwoofer connection too.
1.
Connect a USB thumb drive to the USB port on your computer.
Important:
Make sure there are no music files on the USB thumb drive. This may cause the firmware update to fail.
2.
Go to the Samsung website
(samsung.com)
select Enter Model
Number and enter the model of your
Soundbar. Select manuals and downloads and download the latest software file.
3.
Save the downloaded software to a USB stick and select “Extract Here” to unzip the folder.
4.
Turn off the Soundbar and connect the USB stick containing the software update to the
USB port.
5.
Turn on the Soundbar. Within 3 minutes,
“
UPDATE
” is displayed and updating begins.
6.
When the update finishes, the Soundbar turns off. Press the
p
button on the remote control for 5 seconds. “
INIT
” appears on the display and then the Soundbar turns off.
The update is complete.
• This product has a DUAL BOOT function.
If the firmware fails to update, you can update the firmware again.
7.
Restore your settings on the Soundbar.
ENG - 30
If UPDATE is not displayed
1.
Turn off the Soundbar, disconnect and then reconnect the USB storage device that contains the update files to the Soundbar’s
USB port.
2.
Disconnect the Soundbar’s power cord, reconnect it, and then turn on the Soundbar.
NOTES
• The firmware update may not work properly if audio files supported by the Soundbar are stored in the USB storage device.
• Do not disconnect the power or remove the
USB device while updates are being applied.
The main unit will turn off automatically after completing the firmware update.
• After the update is completed, the user setup in the Soundbar is initialised so you can reset your settings. We recommend you write down your settings so that you can easily reset them after the update. Note that updating firmware resets the subwoofer connection too.
If the connection to the subwoofer is not re-established automatically after the
If the software update fails, check if the USB stick is defective.
• Mac OS users should use MS-DOS (FAT) as the
USB format.
• Updating via USB may not be available, depending on the USB storage device manufacturer.
ENG - 31
12 TROUBLESHOOTING
Before seeking assistance, check the following.
The unit will not turn on.
Is the power cord firmly plugged into the wall outlet and power adapter?
;
Unplug and reconnect the power cord to the wall outlet and the power adapter to make sure the connection is secure.
Is the power adapter firmly connected to the main unit?
;
Disconnect the power adapter from the
Soundbar, and reconnect to make sure the connection is firm and secure.
A function does not work when the button is pressed.
Is there static electricity in the air?
;
Disconnect the power plug and connect it again.
Sound dropouts occur in BT mode.
;
See the Bluetooth connection sections on
Sound is not produced.
Is the Mute function on?
;
Press the
(Mute)
button to cancel the mute function.
Is the volume set to minimum?
;
Adjust the Volume.
The remote control does not work.
Are the batteries drained?
;
Replace with new batteries.
Is the distance between the remote control and
Soundbar main unit too far?
;
Move the remote control closer to the
Soundbar main unit.
The red LED on the subwoofer blinks and the subwoofer is not producing sound.
This issue can occur if the subwoofer is not connected to the Soundbar main unit.
;
Try to connect your subwoofer again. (See
The subwoofer drones and vibrates noticeably.
Try to adjust the vibration of your subwoofer.
;
Rock the
WOOFER
button on your remote control forward or backward to adjust the subwoofer level. (to -12, or between -6 ~
+6).
ENG - 32
13 LICENCE 14 OPEN SOURCE
LICENCE NOTICE
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
To send inquiries and requests regarding open sources, contact Samsung via Email
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol together, Digital Surround, and the Digital Surround logo are registered trademarks or trademarks of
DTS, Inc. in the United States and/or other countries.
© DTS, Inc. All Rights Reserved.
15 IMPORTANT
NOTES ABOUT
SERVICE
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol together, Virtual:X, and the DTS Virtual:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc.
All Rights Reserved.
• Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.
• An administration fee may be charged if either
(a) an engineer is called out at your request and there is no defect with the product (i.e. where the user manual has not been read).
(b) you bring the unit to a repair centre and there is no defect with the product (i.e. where the user manual has not been read).
• You will be informed of the administration fee amount before a technician visits.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Samsung Electronics Co.,
Ltd. is under license. Other trademarks and trade names are those of their respective owners.
ENG - 33
16 SPECIFICATIONS AND GUIDE
Specifications
Model Name
USB
Weight
Dimensions (W x H x D)
Operating Temperature Range
Operating Humidity Range
AMPLIFIER
Rated Output power
Supported play formats
WIRELESS DEVICE OUTPUT POWER
BT max transmitter power
SRD max transmitter power
HW-Q60T
5V/0.5A
3.4 kg
980.0 x 58.0 x 105.0 mm
+5°C to +35°C
10 % ~ 75 %
30W x 6 + 10W x 2
LPCM 2ch, Dolby Audio™
(supporting Dolby® Digital), DTS, DTS Virtual:X
6mW at 2.402GHz – 2.480GHz
25mW at 5.725GHz – 5.825GHz
Subwoofer Name
Weight
Dimensions (W x H x D)
AMPLIFIER
Rated Output power
WIRELESS DEVICE OUTPUT POWER
SRD max transmitter power
PS-WR65BB
6.2 kg
205.0 x 353.0 x 303.2 mm
160W
25mW at 5.725GHz – 5.825GHz
Overall Standby Power Consumption (W)
Bluetooth
Port deactivation method
2.0W
Press and hold the
SOUND MODE
button for more than 5 seconds to turn off Bluetooth Power function.
NOTES
• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
• Weight and dimensions are approximate.
ENG - 34
• Hereby, Samsung, declares that this equipment is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: http://www.samsung.com go to Support > Search Product
Support and enter the model name.
This equipment may be operated in all EU countries.
[Correct disposal of batteries in this product]
(Applicable in countries with separate collection systems)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66.
If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
For information on Samsung’s environmental commitments and product specific regulatory obligations e.g. REACH, WEEE, Batteries, visit: http://www.samsung.com/uk/aboutsamsung/samsungelectronics/corporatecitizenship/data_corner.html
COMMISSION REGULATION (EU) 2019/1782
Ecodesign requirements for external power supplies : www.samsung.com/global/ecodesign_component
ENG - 35
SICHERHEITSINFORMATIONEN
HINWEISE ZUR SICHERHEIT
ZUR VERMEIDUNG VON STROMSCHLÄGEN DARF
DIESES GERÄT NICHT GEÖFFNET WERDEN.
ES ENTHÄLT KEINE BAUTEILE, DIE VOM
BENUTZER GEWARTET ODER REPARIERT
WERDEN KÖNNEN. WARTUNGS- UND
REPARATURARBEITEN DÜRFEN NUR VON
FACHPERSONAL AUSGEFÜHRT WERDEN.
In der nachstehenden Tabelle finden Sie eine
Erklärung zu Symbolen, die sich möglicherweise auf Ihrem Samsung-Produkt befinden.
ACHTUNG
GEFAHR ELEKTRISCHER
SCHLÄGE! GERÄT NICHT
ÖFFNEN!
Dieses Symbol zeigt an, dass im Inneren
Hochspannung vorhanden ist. Es ist gefährlich, Teile im Inneren dieses
Bildschirms zu berühren.
WARNUNG
Dieses Symbol weist darauf hin, dass diesem Gerät wichtige Anweisungen zum
Betrieb und zur Wartung beigefügt sind.
Produkt der Klasse-II: Dieses Symbol zeigt an, dass das Gerät keinen elektrischen Erdungsanschluss (Masse) benötigt. Wenn dieses Symbol bei einem
Produkt mit Netzkabel nicht vorhanden ist, MUSS das Produkt zuverlässig mit einem Schutzleiter (Erde) verbunden sein.
Wechselspannung: Dieses Symbol zeigt an, dass es sich bei der mit diesem
Symbol gekennzeichneten
Nennspannung um eine
Wechselspannung handelt.
Gleichspannung: Dieses Symbol zeigt an, dass es sich bei der mit diesem Symbol gekennzeichneten Nennspannung um eine Gleichspannung handelt.
Achtung! Gebrauchsanweisung beachten: Dieses Symbol weist den
Benutzer an, weitere sicherheitsrelevante Informationen der
Gebrauchsanweisung zu entnehmen.
DEU - ii
• Setzen Sie das Gerät nicht Nässe oder
Feuchtigkeit aus, um die Gefahr eines
Brandes bzw. eines elektrischen Schlags zu vermeiden.
ACHTUNG
• UM ELEKTRISCHE SCHLÄGE ZU VERMEIDEN,
RICHTEN SIE DEN BREITEN KONTAKTSTIFT
DES STECKERS AN DEM BREITEN
STECKPLATZ AUS, UND STECKEN SIE DEN
STECKER VOLL EIN.
• Dieses Gerät darf nur an eine Netzsteckdose mit Schutzerdung angeschlossen werden.
• Um das Gerät vom Netzbetrieb zu trennen, muss der Stecker aus der Netzsteckdose gezogen werden. Deshalb sollte der
Netzstecker jederzeit zugänglich und leicht trennbar sein.
• Das Gerät keinem Spritz- oder Tropfwasser aussetzen. Keine mit Flüssigkeit gefüllten
Behälter, wie Vasen auf das Gerät stellen.
• Um das Gerät vollständig auszuschalten, muss der Netzstecker aus der Steckdose gezogen werden. Somit muss der Netzstecker immer bequem erreichbar sein.
HINWEISE
1.
Stellen Sie sicher, dass die Stromversorgung in Ihrem Haushalt den auf dem Etikett auf der Unterseite des Geräts angegebenen
Anforderungen entspricht. Stellen Sie Ihr
Produkt horizontal auf einer geeigneten
Unterlage (Möbel) auf, so dass rundherum ausreichend Platz 7~10 cm zur Belüftung bleibt. Achten Sie darauf, dass die
Belüftungsöffnungen nicht abgedeckt sind.
Stellen Sie das Gerät nicht auf Verstärker oder andere Geräte, die heiß werden können.
Das Gerät ist für Dauerbetrieb eingerichtet.
Um das Gerät vollständig auszuschalten, den
Stecker aus der Steckdose ziehen. Ziehen Sie den Netzstecker des Geräts wenn Sie beabsichtigen, es für längere Zeit nicht zu nutzen.
2.
Ziehen Sie bei Gewittern das Stromkabel aus der Steckdose. Durch Blitze verursachte
Spannungsspitzen können zur Beschädigung des Geräts führen.
3.
Halten Sie das Gerät von direkter
Sonneneinstrahlung oder anderen
Wärmequellen fern. Dies kann zu einer
Überhitzung führen und zu einer
Fehlfunktion des Geräts führen.
4.
Schützen Sie das Produkt vor Feuchtigkeit
(z. B. Vasen), übermäßiger Hitze (z. B.
Kamine) oder Geräten, die starke magnetische oder ele trische Felder erzeugen. Trennen Sie das Netzkabel bei
Fehlfunktionen des Geräts von der
Stromversorgung. Ihr Produkt ist nicht für den gewerblichen Einsatz vorgesehen.
Verwenden Sie dieses Produkt nur für den privaten Bereich. Wenn Ihr Produkt oder die
CD bei kalten Temperaturen aufbewahrt wurden, kann Kondensation auftreten. Wenn
Sie das Gerät bei kaltenTemperaturen transportiert haben, warten Sie mit der
Inbetriebnahme circa 2 Stunden, bis das
Gerät Raumtemperatur erreicht hat.
5.
Die in diesem Produkt verwendeten
Batterien enthalten umweltschädliche
Chemikalien. Entsorgen Sie die Batterien nicht im Hausmüll. Entsorgen Sie Batterien niemals in einem Feuer. Schließen Sie die
Batterien nicht kurz, zerlegen und
überhitzen Sie sie nicht.
Bei unsachgemäßem Austausch von
Batterien besteht Explosionsgefahr. Setzen
Sie nur Batterien des gleichen oder eines gleichwertigen Typs ein.
ÜBER DIESES HANDBUCH
Das Benutzerhandbuch hat zwei Teile: dieses einfache BENUTZERHANDBUCH auf Papier und ein detailliertes VOLLSTÄNDIGES HANDBUCH, welches Sie herunterladen können.
BENUTZERHANDBUCH
Siehe dieses Handbuch für Sicherheitshinweise,
Produktinstallation, Komponenten,
Verbindungen und Produktspezifikationen.
VOLLSTÄNDIGES HANDBUCH
Sie können auf die VOLLSTÄNDIGES
HANDBUCH im Online-Kundendienstcenter von Samsung durch Scannen des QR-Codes zugreifen. Um die Gebrauchsanweisung auf
Ihrem PC oder Mobilgerät anzusehen, laden
Sie sich die Gebrauchsanweisung im
Dokumentenformat von der Samsung-
Webseite herunter.
(http://www.samsung.com/support)
Design und technische Daten können sich ohne vorherige Ankündigung ändern.
DEU - iii
INHALT
01 Überprüfen der Komponenten 2
Einlegen der Batterien vor der Verwendung der Fernbedienung
02 Produktübersicht
Bedienfeld auf der Vorder-/Oberseite der Soundbar
03 Anschliessen der Soundbar
3
5
Verbinden der Soundbar mit dem Subwoofer
– Automatische Verbindung zwischen Subwoofer und Soundbar
– Manuelles Verbinden des Subwoofers bei Fehlschlagen der automatischen Verbindung
Verbinden des SWA-8500S (separat erhältlich) mit einer Soundbar
04 Anschluss an ihr Fernsehgerät
10
Methode 1. Verbindung mit einem Kabel
– Einen Fernseher über ein HDMI-Kabel verbinden
– Verbindung mit einem optischen Kabel
Methode 2. Drahtlose Verbindung
– Verbindung eines Fernsehers per Bluetooth
05 Verbindung Mit Einem Externen Gerat
Herstellen 15
Verbindung mit einem optischen Kabel
06 Verbinden eines USB speichergeräts
17
DEU - iv
07 Anschliessen eines Mobilgeräts
08 Verwenden der Fernbedienung
18
22
So verwenden Sie die Fernbedienung
Anpassen der Soundbar-Lautstärke mit einer TV-Fernbedienung
Verwenden der verborgenen Tasten (Tasten mit mehr als einer funktion)
Ausgabe-spezifikationen für die unterschiedlichen sound-effekt-modi
09 Installieren der Wandhalterung 27
Vorsichtsmaßnahmen für die Installation
Komponenten für die Anbringung an der Wand
10 Platzieren der Soundbar auf einem TV-ständer
29
11 Softwareaktualisierung
Wenn UPDATE nicht angezeigt wird
12 Fehlerbehebung
30
32
13 Lizenz
14 Bekanntmachung zu Open Source Lizenzen
15 Wichtige Hinweise zum Kundendienst
16 Spezifikationen und Leitfaden
33
33
33
34
DEU - v
01 ÜBERPRÜFEN DER KOMPONENTEN
PAIR
VOL WOOFER
SOUNDBAR
Soundbar-Hauptgerät Subwoofer Fernbedienung / Batterien
x 2
Stromkabel
(Subwoofer, Soundbar)
Netzadapter
(Soundbar)
HDMI-Kabel
Montagehilfe für die Wandhalterung
x 2
Aufhängungsschraube
x 2
Wandhalterung
x 2
Schraube
• Weitere Informationen zur benötigten Stromversorgung und zum Stromverbrauch finden Sie auf dem Etikett am Gerät. (Etikett: Unterseite des Soundbar-Hauptgeräts)
• Wenden Sie sich für den Kauf zusätzlicher Komponenten oder optionaler Kabel an ein
Servicezentrum oder den Kundendienst von Samsung.
• Das Aussehen des Zubehörs kann etwas von den Abbildungen oben abweichen.
Einlegen der Batterien vor der Verwendung der Fernbedienung
(AA-Batterien X 2)
Schieben Sie die rückseitige Abdeckung in
Pfeilrichtung, bis sie vollständig entfernt ist.
Legen Sie 2 AA-Batterien (1,5V) so ausgerichtet ein, dass ihre Polarität richtig ist. Schieben Sie die rückseitige Abdeckung wieder vollständig zurück.
DEU - 2
02 PRODUKTÜBERSICHT
Bedienfeld auf der Vorder-/Oberseite der Soundbar
Positionieren Sie das
Produkt so, dass sich das
SAMSUNG Logo auf der
Oberseite befindet.
Bedienfeld auf der Oberseite
Anzeige
Zeigt den Status und den aktuellen Modus des Produkts an.
(Strom)-Taste
Schaltet den Strom ein und aus.
•
Auto Power Down-Funktion
In folgenden Situationen wird das Gerät automatisch ausgeschaltet.
– Modus
D.IN
/
HDMI
/
BT
/
USB
: Wenn seit mehr als 20 Minuten kein Audiosignal empfangen wurde.
-/+ (Lautstärke)-Taste
Stellt die Lautstärke ein.
• Der Lautstärkepegel wird beim Einstellen auf der vorderen Anzeige der Soundbar angezeigt.
(Quelle)-Taste
Wählt den Quelleneingangsmodus aus.
Eingangsmodus
Optischer digitaler Eingang
ARC (HDMI OUT)-Eingang
HDMI-Eingang
BLUETOOTH-Modus
USB-Modus
D.IN
Anzeige
D.IN
TV ARC (Automatische Umwandlung)
HDMI
BT
USB
• Zum Einschalten des Modus „
BT PAIRING
“ schalten Sie die Quelle auf den Modus „
BT
“ um und halten
Sie dann die taste
(Quelle)
länger als 5 Sekunden lang gedrückt.
• Nach dem Anschluss des Netzkabels muss 4 bis 6 Sekunden gewartet werden, bis der Netzschalter bedient werden kann.
• Wenn Sie dieses Gerät einschalten, vergeht eine Verzögerungszeit von 4 bis 5 Sekunden, bevor eine
Tonausgabe erfolgt.
• Wenn Sie den Ton nur über den Soundbar hören wollen, müssen Sie die Lautsprecher des
Fernsehgeräts im Audio Setup Menü Ihres Fernsehgeräts ausschalten. Weitere Informationen über
Ihr Fernsehgerät finden Sie im Benutzerhandbuch, das im Lieferumfang Ihres TVs enthalten war.
DEU - 3
Unterseite der Soundbar
HDMI
USB (5V 0.5A)
DC 24V
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
Hier ein USB-Gerät anschließen, um Musikdateien auf dem USB-Gerät über die Soundbar wiederzugeben.
DC 24V (Stromversorgungseingang)
Den Netzadapter anschließen.
HDMI
Gibt digitale Video- und Audiosignale über ein HDMI-Kabel simultan ein.
An den HDMI-Ausgang eines externen Geräts anschließen.
HDMI TO TV (ARC)
An die HDMI (ARC)-Buchse an einem Fernseher anschließen.
DIGITAL AUDIO IN (OPTICAL)
An den digitalen (optischen) Ausgang eines externen Geräts anschließen.
• Ziehen Sie, wenn Sie das Stromkabel des AC/DC-Adapters von der Steckdose trennen möchten, am
Stecker. Ziehen Sie nicht am Kabel.
• Schließen Sie dieses Gerät oder andere Geräteteile nicht an eine AC-Steckdose an, bis alle
Anschlüsse zwischen den Teilen hergestellt sind.
DEU - 4
03 ANSCHLIESSEN DER SOUNDBAR
Stromanschluss
Verwenden Sie die Stromkomponenten, um den Subwoofer und die Soundbar in der folgenden
Reihenfolge an die Stromversorgung anzuschließen:
1.
Schließen Sie das Stromkabel an den Subwoofer an.
2.
Schließen Sie das Stromausgangskabel an das Netzteil und danach an die Soundbar an.
3.
Schließen Sie das Stromkabel an die Steckdose an.
Siehe die nachfolgenden Abbildungen.
• Weitere Informationen zur benötigten Stromversorgung und zum Stromverbrauch finden Sie auf dem Etikett am Gerät. (Etikett: Unterseite des Soundbar-Hauptgeräts)
POWER
Stromkabel
Stromkabel
DC 24V
Stromanschluss
Netzadapter
USB (5V 0.5A)
DC 24V
Unterseite des
Soundbar-Hauptgeräts
Rückseite des
Subwoofers
Stromanschluss
• Achten Sie darauf, dass der Netzadapter flach auf einem Tisch oder dem Fußboden liegt.
Wenn Sie den Netzadapter in hängender Position mit dem Netzkabeleingang nach oben platzieren, könnten Wasser oder sonstige Fremdstoffe in den Adapter gelangen und zu Fehlfunktionen führen.
DEU - 5
Verbinden der Soundbar mit dem Subwoofer
Wenn der Subwoofer verbunden ist, können Sie einen vollen Bass-Ton genießen.
Automatische Verbindung zwischen Subwoofer und Soundbar
Wenn Sie den Strom einschalten, nachdem Sie die Stromkabel an die Soundbar und den Subwoofer angeschlossen haben, wird der Subwoofer automatisch mit der Soundbar verbunden.
• Wenn die automatische Kopplung abgeschlossen ist, leuchten die blauen Anzeigeleuchten auf der
Rückseite des Subwoofers auf.
LED-Anzeigelichter auf der Rückseite des Subwoofers
LED
Blau
Rot
Rot und blau
Status
Ein
Beschreibung
Erfolgreich verbunden
(normaler Betrieb)
-
Abhilfe
Blinkend
Ein
Verbindung wird wieder hergestellt
Prüfen Sie, ob das am Soundbar-Hauptgerät angeschlossene Stromkabel richtig verbunden ist oder warten Sie 5 Minuten. Falls das Blinken andauert, versuchen Sie, den Subwoofer
manuell anzuschließen. Siehe Seite 7.
Standby (bei ausgeschaltetem
Soundbar-Hauptgerät)
Verbindung fehlgeschlagen
Blinkend Fehlfunktion
Prüfen Sie, ob das Stromkabel richtig am
Soundbar-Hauptgerät angeschlossen ist.
Erneut verbinden. Siehe die Anweisungen zur
manuellen Verbindung auf Seite 7.
Siehe die Kontaktinformationen für das
Samsung Servicezentrum in dem Handbuch.
DEU - 6
Manuelles Verbinden des Subwoofers bei Fehlschlagen der automatischen Verbindung
Vor dem Ausführen der folgenden Verbindungsschritte:
• Überprüfen Sie, ob die Stromkabel der Soundbar und des Subwoofers richtig angeschlossen sind.
• Stellen Sie sicher, dass die Soundbar eingeschaltet ist.
1.
Halten Sie
ID SET
auf der Rückseite des Subwoofers mindestens 5 Sekunden lang gedrückt.
• Die rote Anzeigeleuchte auf der Rückseite des Subwoofers erlischt und die blaue
Anzeigeleuchte blinkt.
5 Sec
Rückseite des Subwoofers
2.
Halten Sie die Taste
Oben
auf der Fernbedienung länger als 5 Sekunden gedrückt.
• Für kurze Zeit erscheint nun die Meldung
ID SET
im Display der Soundbar und erlischt dann.
• Die Soundbar wird automatisch eingeschaltet, wenn
ID SET
abgeschlossen ist.
PAIR
5 Sec
Das SAMSUNG-Logo befindet sich auf der Oberseite
ID SET
SOUN
D
MOD
E
3.
Prüfen Sie, ob die LINK-LED blau leuchtet (Verbindung hergestellt).
Die LINK-LED-Anzeige blinkt nicht länger, sondern leuchtet blau, wenn zwischen der
Soundbar und dem Wireless-Subwoofer eine
Verbindung besteht.
Leuchtet blau
DEU - 7
HINWEISE
• Schließen Sie das Stromkabel dieses Produkts oder Ihr TV-Gerät nicht an eine Steckdose an, bis alle
Anschlüsse zwischen den Teilen hergestellt sind.
• Stellen Sie vor dem Verschieben oder Aufstellen des Produkts sicher, dass das Gerät ausgeschaltet ist und das Stromkabel getrennt.
• Wenn die Haupteinheit ausgeschaltet ist, geht der drahtlose Subwoofer in den Standby-Modus und die STANDBY-LED auf der Rückseite blinkt mehrmals blau und wird dann rot.
• Wenn Sie in der Nähe der Soundbar ein Gerät mit gleicher Frequenz (5,8GHz) verwenden, kann es zu Interferenzen und damit zu Tonunterbrechungen kommen.
• Die maximale Übertragungsentfernung des drahtlosen Signals der Haupteinheit beträgt ca. 10 m, kann jedoch in Abhängigkeit Ihrer Betriebsumgebung unterschiedlich sein. Wenn sich eine
Stahlbeton- oder Metallwand zwischen der Haupteinheit und dem drahtlosen Subwoofer befindet, funktioniert die Anlage möglicherweise gar nicht, weil das drahtlose Signal Metall nicht durchdringen kann.
VORSICHTSMASSNAHMEN
• Es sind Antennen für den drahtlosen Empfang in den drahtlosen Subwoofer eingebaut. Halten Sie die Einheiten fern von Wasser und Feuchtigkeit.
• Für eine optimale Wiedergabeleistung stellen Sie sicher, dass der Bereich um den drahtlosen
Subwoofer und das Drahtlosempfängermodul (separat erhältlich) frei von Behinderungen ist.
Verbinden des SWA-8500S (separat erhältlich) mit einer Soundbar
Erweitern Sie das System um echten drahtlosen Surround-Sound, indem Sie das Drahtlose
Rücklautsprecherkit (SWA-8500S, separat erhältlich) von Samsung an Ihre Soundbar anschließen.
1.
Verbinden Sie das drahtlose Empfangsmodul an 2 Surround-Lautsprecher.
– Die Lautsprecherkabel sind farbcodiert.
SURROUND-LEFT
SURROUND-LEFT
L
L R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
ID SET
R
SURROUND SPEAKERS OUT
ID SET
SURROUND-RIGHT
SURROUND-RIGHT
DEU - 8
2.
Überprüfen Sie den Standby-Status des drahtlosen Empfangsmoduls, nachdem es an eine
Steckdose angeschlossen worden ist.
• Die LINK LED-Anzeige (blaue LED-Lampe) auf dem drahtlosen Empfängermodul blinkt. Wenn die LED nicht blinkt, halten Sie die Taste
ID SET
auf der Rückseite des drahtlosen
Rücklautsprecherkits mit einer Stiftspitze 5 bis 6 Sekunden lang gedrückt, bis die LED-
Verbindungsanzeige LINK auf dem drahtlosen Rücklautsprecherkit blinkt (blau). Weitere
Informationen zur LED finden Sie im Benutzerhandbuch des SWA-8500S.
SURROUND SPEAKERS OUT
R
5 Sec
ID SET
ID SET
STANDBY
LINK
STANDBY
LINK
POWER
Blinkt blau
POWER
3.
Halten Sie die Taste
Oben
auf der Fernbedienung länger als 5 Sekunden gedrückt.
• Für kurze Zeit erscheint nun die Meldung
ID SET
im Display der Soundbar und erlischt dann.
• Die Soundbar wird automatisch eingeschaltet, wenn
ID SET
abgeschlossen ist.
PAIR
5 Sec
Das SAMSUNG-Logo befindet sich auf der Oberseite
ID SET
SOUN
D
MOD
E
ACHTUNG
• Wenn die Soundbar Musik abspielt, während sie mit der SWA-8500S eine Verbindung herstellt, hören Sie möglicherweise ein Stottern aus dem Woofer, während die Verbindung hergestellt wird.
4.
Prüfen Sie, ob die LINK-LED blau leuchtet (Verbindung hergestellt).
STANDBY
LINK
STANDBY
LINK
Die LINK-LED-Anzeige blinkt nicht länger, sondern leuchtet blau, wenn zwischen der
Soundbar und dem drahtlosen
Empfangsmodul eine Verbindung besteht.
Leuchtet blau
5.
Wenn der SWA-8500S nicht angeschlossen ist, wiederholen Sie den Vorgang ab Schritt 2.
DEU - 9
04 ANSCHLUSS AN IHR FERNSEHGERÄT
Hören Sie den TV-Ton durch kabelgebundene oder kabellose Verbindungen über Ihre Soundbar.
• Wenn die Soundbar an einen ausgewählten Samsung TV angeschlossen ist, kann die Soundbar über die Fernbedienung des Fernsehers bedient werden.
– Diese Funktion wird durch Samsung Smart-Fernsehermodelle von 2017 und später unterstützt, die Bluetooth unterstützen, wenn Sie die Soundbar mit einem optischen Kabel mit dem
Fernseher verbinden.
– Mit dieser Funktion können Sie auch das TV-Menü verwenden, um das Klangfeld und verschiedene Einstellungen sowie die Lautstärke und die Stummschaltung anzupassen.
Methode 1. Verbindung mit einem Kabel
Wenn Rundfunksignale Dolby Digital sind und die Einstellung für „Digitales Ausgangsaudioformat” auf Ihrem
Fernseher auf PCM gestellt ist, wird empfohlen, die Einstellung auf Dolby Digital zu ändern. Nach dem
Ändern der Einstellung können Sie eine bessere Soundqualität genießen. (Das Menü des Fernsehers kann je nach dem Hersteller des Fernsehers unterschiedliche Bezeichnungen für Dolby Digital und PCM verwenden.)
Einen Fernseher über ein HDMI-Kabel verbinden
Überprüfen Sie (ARC) am
HDMI IN-Anschluss Ihres
Fernsehers.
HDMI-Kabel
Unterseite der Soundbar
HDMI IN
(ARC)
Überprüfen Sie den HDMI TO TV (ARC)
-Anschluss am Soundbar-Hauptgerät.
Oberseite der Soundbar
TV ARC
1.
Bei eingeschalteter Soundbar und eingeschaltetem Fernseher das HDMI-Kabel wie in der
Abbildung gezeigt anschließen.
2.
Das Anzeigefenster des Soundbar-Hauptgeräts zeigt „
TV ARC
“ an und die Soundbar gibt den
TV-Ton wieder.
DEU - 10
• Falls der Ton des Fernsehers nicht hörbar ist, drücken Sie die Taste
(Quelle)
auf der
Fernbedienung oder auf der Oberseite der Soundbar, um in den „
D.IN
“-Modus zu wechseln. Der
Bildschirm zeigt der Reihe nach „
D.IN
“ und „
TV ARC
“ an und der TV-Ton wird wiedergegeben.
• Wenn im Displayfenster des Soundbar-Hauptgeräts „
TV ARC
“ nicht angezeigt wird, stellen Sie sicher, dass das HDMI-Kabel an den korrekten Anschluss angeschlossen ist.
• Ändern Sie die Lautstärke der Soundbar mit den Lautstärketasten an der TV-Fernbedienung.
HINWEISE
• HDMI ist eine Schnittstelle, die die digitale Übertragung von Video- und Audiodaten mit einem einzigen Anschluss ermöglicht.
• Wenn das TV-Gerät über einen ARC-Anschluss verfügt, verbinden Sie das HDMI-Kabel mit dem
HDMI-IN-(ARC)-Anschluss.
• Wir empfehlen, falls möglich, die Verwendung eines kernlosen HDMI-Kabels. Wenn Sie ein HDMI-
Kabel mit Kern verwenden, sollte der Kabeldurchmesser weniger als 14 mm betragen.
• Diese Funktion ist nicht verfügbar, wenn das HDMI-Kabel ARC nicht unterstützt.
Verbindung mit einem optischen Kabel
Unterseite der Soundbar
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
Optisches Kabel
(nicht mitgeliefert)
Oberseite der Soundbar
OPTICAL OUT
D.IN
1.
Verbinden Sie den Anschluss
DIGITAL AUDIO IN (OPTICAL)
der Soundbar über ein optisches
Digitalkabel (nicht mitgeliefert) mit dem Anschluss OPTICAL OUT des Fernsehers.
2.
Drücken Sie die Taste
(Quelle)
auf dem Bedienfeld der Oberseite oder auf der Fernbedienung und wählen Sie dann den „
D.IN
“-Modus aus.
DEU - 11
Verwenden der Q-Symphony-Funktion
Bei der Q-Symphony wird die Soundbar mit einem Samsung Fernsehgerät synchronisiert, um Ton aus zwei Geräten für einen optimalen Surround-Effekt zu erzielen. Wenn die Soundbar verbunden ist, erscheint das Menü „
TV+Soundbar
“ unter dem
Tonausgabe
-Menü des Fernsehgeräts. Wählen Sie das entsprechende Menü aus.
Menü des
Fernsehgeräts
HDMI-Kabel
ODER
D.IN
Optisches Kabel
(nicht mitgeliefert)
• Beispiel für Menü des Fernsehgeräts:
TV Serienbezeichnung + [AV] Soundbar Serienbezeichnung (HDMI)
HINWEISE
• Kann entsprechend des von dem Fernsehgerät unterstützten Codecs betrieben werden.
• Diese Funktion wird nur unterstützt, wenn das HDMI-Kabel oder das optische Kabel (nicht mitgeliefert) verbunden ist.
• Diese Funktion ist bei Samsung Fernsehgeräten verfügbar, die 2020 veröffentlicht wurden, sowie bei einigen Soundbar-Modellen.
DEU - 12
Methode 2. Drahtlose Verbindung
Verbindung eines Fernsehers per Bluetooth
Wenn ein Fernseher über Bluetooth verbunden wird, können Sie einen Stereoton ohne lästige Kabel hören.
• Es kann nur ein Fernseher gleichzeitig verbunden werden.
PAIR
ODER
D
MOD
E
Die erste Verbindung
1.
Drücken Sie die Taste
PAIR
auf der Fernbedienung, um in den Modus „
BT PAIRING
“ zu wechseln.
(ODER)
a.
Drücken Sie die Taste
(Quelle)
auf dem Bedienfeld der Oberseite und wählen Sie dann „
BT
“ aus.
„
BT
“ wird in wenigen Sekunden automatisch zu „
BT PAIRING
“ oder zu „
BT READY
“, falls eine Verbindung bereits verzeichnet wurde.
b.
Wenn „
BT READY
“ erscheint, die Taste
(Quelle)
auf dem Bedienfeld der Oberseite der Soundbar für mehr als 5 Sekunden gedrückt halten, damit „
BT PAIRING
“ angezeigt wird.
2.
Wählen Sie den Bluetooth-Modus an dem Fernseher aus. (Weitere Informationen finden Sie im
Handbuch des Fernsehers.)
3.
Wählen Sie „
[AV] Samsung Soundbar Q6T-Series
“ aus der Liste auf dem Bildschirm des Fernseher aus.
Eine verfügbare Soundbar wird durch „
Need Pairing
“ oder „
Paired
“ auf der Bluetooth-Geräteliste des
Fernsehers angezeigt. Zum Verbinden der Soundbar wählen Sie die Meldung und stellen Sie eine
Verbindung her.
• Wenn der Fernseher verbunden ist, erscheint [
Name des Fernsehers
]“ → „
BT
“ auf der vorderen
Anzeige des Fernsehers.
4.
Sie können den TV-Ton jetzt aus der Soundbar hören.
Falls das Gerät nicht verbunden werden kann
• Falls die Auflistung der zuvor verbundenen Soundbar (z. B. „
[AV] Samsung Soundbar Q6T-Series
“) in der Liste erscheint, löschen Sie sie.
• Wiederholen Sie dann die Schritte 1 bis 3.
HINWEIS
• Nachdem Sie die Soundbar zum ersten Mal mit Ihrem Fernseher verbunden haben, verwenden Sie den Modus „
BT READY
“ um erneut eine Verbindung herzustellen.
DEU - 13
Trennen der Soundbar vom Fernseher
Drücken Sie die Taste
(Quelle)
auf dem Bedienfeld der Oberseite oder auf der Fernbedienung und wechseln Sie dann in einen beliebigen Modus außer in den „
BT
“-Modus.
• Das Trennen dauert einige Zeit, da der Fernseher ein Antwortsignal von der Soundbar empfangen muss. (Die benötigte Zeit kann je nach Fernsehermodell unterschiedlich sein.)
• Um die automatische Bluetooth-Verbindung zwischen der Soundbar und dem Fernsehgerät aufzuheben, drücken Sie die Taste
Links
an der Fernbedienung für 5 Sekunden, wenn sich die
Soundbar im Status „
BT READY
“ befindet. (Einschalten → Ausschalten)
Was ist der Unterschied zwischen BT READY und BT PAIRING?
•
BT READY
: In diesem Modus können Sie nach zuvor verbundenen Fernsehern suchen oder ein zuvor verbundenes Mobilgerät mit der Soundbar verbinden.
•
BT PAIRING
: In diesem Modus können Sie ein neues Gerät mit der Soundbar verbinden. (Drücken
Sie die Taste
PAIR
auf der Fernbedienung oder halten Sie die Taste
(Quelle)
auf der Oberseite der Soundbar für mehr als 5 Sekunden gedrückt, während die Soundbar im „
BT
“-Modus ist.)
HINWEISE
• Falls sie beim Verbinden mit einem Bluetooth-Gerät nach einem PIN-Code gefragt werden, geben
Sie <0000> ein.
• Im Bluetooth-Verbindungsmodus geht die Bluetooth-Verbindung verloren, wenn der Abstand zwischen der Soundbar und dem Bluetooth-Gerät 10 m überschreitet.
• Die Soundbar schaltet sich nach 20 Minuten im Bereitschaftszustand automatisch aus.
• Die Soundbar könnte unter den folgenden Umständen die Bluetooth-Suche oder -Verbindung eventuell nicht korrekt ausführen:
– Wenn die Soundbar von einem starken elektrischen Feld umgeben ist.
– Falls zwei oder mehr Bluetooth-Geräte gleichzeitig mit der Soundbar gekoppelt sind.
– Wenn das Bluetooth-Gerät ausgeschaltet ist, sich nicht an der richtigen Stelle befindet oder nicht funktioniert.
• Elektronische Geräte können Funkstörungen verursachen. Elektromagnetische Wellen erzeugende
Geräte müssen vom Soundbar-Hauptgerät ferngehalten werden - z. B. Mikrowellen, WLAN-Geräte etc.
DEU - 14
05 VERBINDUNG MIT EINEM EXTERNEN
GERAT HERSTELLEN
Stellen Sie über eine Kabel- oder Bluetooth-Verbindung eine Verbindung mit einem externen Gerät her, um den Ton des externen Geräts über die Soundbar wiederzugeben.
Über ein HDMI-Kabel verbinden
Unterseite der Soundbar
HDMI OUT
HDMI
Externes Gerät
HDMI-Kabel
HDMI IN
(ARC)
HDMI-Kabel
Oberseite der Soundbar
HDMI
1.
Verbinden Sie den Anschluss
HDMI
auf der Rückseite des Geräts über ein HDMI-Kabel mit dem
Anschluss HDMI OUT Ihres Digitalgeräts.
2.
Verbinden Sie den Anschluss
HDMI TO TV (ARC)
auf der Rückseite des Geräts über ein
HDMI-Kabel mit dem Anschluss HDMI IN Ihres Fernsehers.
3.
Drücken Sie die Taste
(Quelle)
auf dem Bedienfeld der Oberseite oder auf der Fernbedienung und wählen Sie dann „
HDMI
“ aus.
4.
Der Modus „
HDMI
“ wird auf dem Anzeigefeld der Soundbar angezeigt und der Ton wird wiedergegeben.
DEU - 15
Verbindung mit einem optischen Kabel
Unterseite der Soundbar
DIGITAL AUDIO IN (OPTICAL)
Optisches Kabel
(nicht mitgeliefert)
Oberseite der Soundbar
OPTICAL OUT
BD / DVD-Player /
Set-Top-Box /
Spielkonsole
D.IN
1.
Verbinden Sie den Anschluss
DIGITAL AUDIO IN (OPTICAL)
am Hauptgerät über ein optisches
Digitalkabel (nicht mitgeliefert) mit dem Anschluss OPTICAL OUT des Quellgeräts.
2.
Wählen Sie den „
D.IN
“-Modus aus, indem Sie die Taste
(Quelle)
auf dem Bedienfeld der
Oberseite oder auf der Fernbedienung drücken.
DEU - 16
06 VERBINDEN EINES USB SPEICHERGERÄTS
Sie können Musikdateien, die sich auf Speichergeräten befinden, über die Soundbar wiedergeben.
USB-Anschluss
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
USB
1.
Verbinden Sie das USB-Gerät mit dem USB-Anschluss an der Unterseite des Geräts.
2.
Drücken Sie die Taste
(Quelle)
auf dem Bedienfeld der Oberseite oder auf der Fernbedienung und wählen Sie dann „
USB
“ aus.
3.
Auf dem Anzeigebildschirm wird „
USB
“ angezeigt.
4.
Musikdateien vom Speichergerät über die Soundbar wiedergeben.
• Die Soundbar wird automatisch ausgeschaltet (Auto Power Down), wenn länger als
20 Minuten kein USB-Gerät angeschlossen wurde.
Kompatibilitätsliste
Verlängerung
*.mp3
Codec
MPEG1 Layer2
MPEG1 Layer3
MPEG2 Layer3
MPEG2.5 Layer3
WMA7/8/9 (Nur Audio)
Vorbis
Samplingrate
32kHz ~ 48kHz
32kHz ~ 48kHz
16kHz ~ 24kHz
8kHz ~ 12kHz
32kHz ~ 48kHz
32kHz ~ 48kHz
Bitrate
32 ~ 320kbps
32 ~ 320kbps
8 ~ 160kbps
8 ~ 160kbps
32 ~ 320kbps
45 ~ 500kbps
*.wma
*.ogg
*.aac
*.m4a
*.mp4
*.wav
*.flac
*.aiff
AAC-LC
(MPEG2/MPEG4 Nur Audio)
32kHz ~ 48kHz 32 ~ 320kbps
LPCM
FLAC
AIFF
32kHz ~ 192kHz
32kHz ~ 192kHz
32kHz ~ 192kHz
1024 ~ 9216kbps
162 ~ 8100kbps
1024 ~ 9216kbps
• Sind zu viele Ordner und Dateien auf dem USB-Gerät gespeichert, kann es einige Zeit dauern, bis die Soundbar auf die Dateien zugreifen und abspielen kann.
DEU - 17
07 ANSCHLIESSEN EINES MOBILGERÄTS
Anschließen per Bluetooth
Wenn ein Mobilgerät über Bluetooth verbunden wird, können Sie einen Stereoton ohne lästige Kabel hören.
• Die Verbindung ist auf einen Fernseher oder zwei Bluetooth-Geräte gleichzeitig eingeschränkt.
PAIR
ODER
Bluetooth-Gerät
D
MOD
E
Die erste Verbindung
1.
Drücken Sie die Taste
PAIR
auf der Fernbedienung, um in den Modus „
BT PAIRING
“ zu wechseln.
(ODER)
a.
Drücken Sie die Taste
(Quelle)
auf dem Bedienfeld der Oberseite und wählen Sie dann „
BT
“ aus.
„
BT
“ wird in wenigen Sekunden automatisch zu „
BT PAIRING
“ oder zu „
BT READY
“, falls eine Verbindung bereits verzeichnet wurde.
b.
Wenn „
BT READY
“ erscheint, die Taste
(Quelle)
auf dem Bedienfeld der Oberseite der
Soundbar für mehr als 5 Sekunden gedrückt halten, damit „
BT PAIRING
“ angezeigt wird.
2.
Wählen Sie „
[AV] Samsung Soundbar Q6T-Series
“ aus der Liste aus.
• Wenn eine Soundbar mit dem Bluetooth-Gerät verbunden ist, wird [
Bluetooth-Gerätename
] →
„
BT
“ in der vorderen Anzeige angezeigt.
3.
Geben Sie Musikdateien auf dem über Bluetooth verbundenen Gerät über die Soundbar aus.
Falls das Gerät nicht verbunden werden kann
• Falls die Auflistung der zuvor verbundenen Soundbar (z. B. „
[AV] Samsung Soundbar Q6T-Series
“) in der Liste erscheint, löschen Sie sie.
• Wiederholen Sie dann Schritt 1 und 2.
HINWEIS
• Nachdem Sie die Soundbar zum ersten Mal mit Ihrem Mobilgerät verbunden haben, verwenden Sie den Modus „
BT READY
“ um erneut eine Verbindung herzustellen.
DEU - 18
Was ist der Unterschied zwischen BT READY und BT PAIRING?
•
BT READY
: In diesem Modus können Sie nach zuvor verbundenen Fernsehern suchen oder ein zuvor verbundenes Mobilgerät mit der Soundbar verbinden.
•
BT PAIRING
: In diesem Modus können Sie ein neues Gerät mit der Soundbar verbinden. (Drücken
Sie die Taste
PAIR
auf der Fernbedienung oder halten Sie die Taste
(Quelle)
auf der Oberseite der Soundbar für mehr als 5 Sekunden gedrückt, während die Soundbar im „
BT
“-Modus ist.)
HINWEISE
• Falls sie beim Verbinden mit einem Bluetooth-Gerät nach einem PIN-Code gefragt werden, geben
Sie <0000> ein.
• Im Bluetooth-Verbindungsmodus geht die Bluetooth-Verbindung verloren, wenn der Abstand zwischen der Soundbar und dem Bluetooth-Gerät 10 m überschreitet.
• Die Soundbar schaltet sich nach 20 Minuten im Bereitschaftszustand automatisch aus.
• Die Soundbar könnte unter den folgenden Umständen die Bluetooth-Suche oder -Verbindung eventuell nicht korrekt ausführen:
– Wenn die Soundbar von einem starken elektrischen Feld umgeben ist.
– Falls mehrere Bluetooth-Geräte gleichzeitig mit der Soundbar gekoppelt werden.
– Wenn das Bluetooth-Gerät ausgeschaltet ist, sich nicht an der richtigen Stelle befindet oder nicht funktioniert.
• Elektronische Geräte können Funkstörungen verursachen. Elektromagnetische Wellen erzeugende
Geräte müssen vom Soundbar-Hauptgerät ferngehalten werden - z. B. Mikrowellen, WLAN-Geräte etc.
• Der Soundbar unterstützt SBC data (44,1kHz, 48kHz).
• Nur an ein Bluetooth-Gerät anschließen, das die A2DP (AV) Funktion unterstützt.
• Es kann keine Verbindungen zwischen dem Soundbar und Bluetooth-Geräten hergestellt werden, die nur die HF (Hands Free) Funktion unterstützen.
• Nachdem Sie eine Verbindung zwischen der Soundbar und einem Bluetooth-Gerät hergestellt haben, wird durch Auswahl von „
[AV] Samsung Soundbar Q6T-Series
“ aus der Liste der gefundenen Geräte die Soundbar automatisch in den „
BT
“-Modus umgeschaltet.
– Ist nur verfügbar, wenn der Soundbar in der Liste der verbundenen Geräte des Bluetooth-
Geräts aufgelistet ist. (Es muss zuvor mindestens einmal eine Verbindung zwischen dem
Soundbar und dem Bluetooth-Gerät hergestellt worden sein.)
• Der Soundbar erscheint nur in der Liste der vom Bluetooth-Gerät gefundenen Geräte, wenn der
Soundbar „
BT READY
“ anzeigt.
Bluetooth Power Ein (SOUND MODE)
Wenn die Funktion das Gerät über Bluetooth Power Ein aktiviert und der Soundbar ausgeschaltet ist und ein Bluetooth-Gerät, mit dem bereits zuvor eine Verbindung mit dem Soundbar hergestellt wurde, versucht, eine Verbindung mit dem Soundbar herzustellen, schaltet sich der Soundbar automatisch ein.
1.
Halten Sie die Taste
SOUND MODE
mindestens 5 Sekunden gedrückt, während die Soundbar eingeschaltet ist.
2.
Auf dem Display der Soundbar erscheint „
ON-BLUETOOTH POWER
“.
DEU - 19
Das Bluetooth-Gerät von der Soundbar trennen
Sie können die Verbindung zwischen dem Bluetooth-Gerät und Soundbar trennen. Die Anleitung hierzu finden Sie in der Bedienungsanleitung des Bluetooth-Geräts.
• Verbindung zum Soundbar wird getrennt.
• Wenn die Soundbar von dem Bluetooth-Gerät getrennt ist, zeigt die Soundbar „
BT DISCONNECTED
“ auf der vorderen Anzeige an.
Trennen der Soundbar vom Bluetooth-Gerät
Drücken Sie die Taste
(Quelle)
auf dem Bedienfeld oder Oberseite oder auf der Fernbedienung und wechseln Sie dann in einen beliebigen Modus außer in den „
BT
“-Modus.
• Das Trennen dauert einige Zeit, da das Bluetooth-Gerät ein Antwortsignal von der Soundbar empfangen muss. (Die Zeit zum Trennen kann je nach Bluetooth-Gerät unterschiedlich sein)
• Wenn die Soundbar von dem Bluetooth-Gerät getrennt ist, zeigt die Soundbar „
BT DISCONNECTED
“ auf der vorderen Anzeige an.
HINWEISE
• Bei einer Bluetooth Verbindung geht die Bluetooth Verbindung verloren, wenn der Abstand zwischen dem Soundbar und dem Bluetooth Gerät 10 m überschreitet.
• Wenn sich der Soundbar für mehr als 20 Minuten im Bereitschaftszustand befindet, schaltet er sich automatisch aus.
Mehr über Bluetooth
Bluetooth ist eine neue Technologie, mit der es möglich ist, Bluetooth-fähige Geräte über eine kurze
Funkverbindung miteinander zu verbinden.
• Ein Bluetooth Gerät kann Störungen erzeugen oder falsch funktionieren, wenn:
– Das Empfangs-/Sendesystem eines Bluetooth-Geräts oder der Haupteinheit mit einem
Körperteil berührt wird.
– Die Funkübertragung durch Wände, Ecken oder Bürotrennwände behindert wird.
– Interferenzen mit Geräten auftreten, welche dasselbe Frequenzband verwenden, wie medizinische Geräte, Mikrowellenherde oder Funknetzwerke.
• Wenn Sie Soundbar über das Bluetooth Gerät betreiben möchten, stellen Sie sicher, dass der
Abstand kurz gehalten wird.
• Mit zunehmender Entfernung zwischen Soundbar und Bluetooth-Gerät nimmt die Qualität der
Bluetooth-Verbindung ab. Wenn die Distanz den Bluetooth-Betriebsbereich übersteigt, geht die
Verbindung verloren.
• In Gebieten mit geringer Empfangssensibilität ist die Funktion der Bluetooth-Verbindung möglicherweise eingeschränkt.
• Die Bluetooth-Verbindung funktioniert nur mit Geräten in unmittelbarer Nähe. Die Verbindung wird automatisch unterbrochen, wenn dieser Radius überschritten wird. Selbst innerhalb dieses Radius kann die Klangqualität durch Hindernisse wie Mauern oder Türen beeinträchtigt werden.
• Dieses Drahtlosgerät kann während des Betriebs elektrische Störungen verursachen.
DEU - 20
Bluetooth-Mehrfachverbindung
Die Soundbar kann mit 2 Bluetooth-Geräten gleichzeitig verbunden werden.
Bluetooth-Gerät A Bluetooth-Gerät B
1.
Verbinden Sie die Soundbar mit bis zu zwei Bluetooth-Geräten. (Weitere Informationen finden Sie
2.
Spielen Sie Musik von einem der angeschlossenen Bluetooth-Geräte ab, während zwei Geräte verbunden sind.
3.
Um Musik vom Bluetooth-Gerät „B“ während der Wiedergabe vom Gerät „A“ abzuspielen, pausieren oder stoppen Sie die Wiedergabe auf dem Gerät „A“ und starten Sie dann die
Wiedergabe auf dem Gerät „B“.
• Das Gerät schaltet nicht um, wenn Musik vom Gerät „B“ abgespielt wird, ohne dass das Gerät
„A“ zuerst pausiert oder gestoppt wird.
4.
In früheren Versionen als AVRCP V1.4 kann die Schaltzeit des Gerätes, das Musik abspielt, verzögert sein.
HINWEISE
• Falls Sie versuchen ein 3. Bluetooth-Gerät zu verbinden, werden die Geräte A oder B getrennt.
(Das Gerät, welches gerade nicht abspielt wird, wird getrennt.)
• Es können nur ein Samsung Fernsehgerät oder 2 Bluetooth-Geräte gleichzeitig angeschlossen werden.
• Die Soundbar wird von Bluetooth-Geräten getrennt, wenn sie eine Verbindungsanforderung von einem Samsung-TV erhält.
DEU - 21
08 VERWENDEN DER FERNBEDIENUNG
So verwenden Sie die Fernbedienung
SOUND
MODE
PAIR
VOL WOOFER
SOUNDBAR
Schaltet die Soundbar ein und aus.
VOL
Strom
Drücken Sie dies, um eine an die Soundbar angeschlossene Quelle auszuwählen.
Quelle
Stummschaltung
Drücken Sie die Taste (
Stummschaltung
), um den Ton stumm zu schalten. Drücken Sie sie erneut, um den Ton wieder einzuschalten.
SOUND
MODE
SOUND MODE
SOUND
Sie können den gewünschten Toneffekt durch
Wahl von
STANDARD
,
SURROUND SOUND
,
GAME PRO
,
ADAPTIVE SOUND
oder
DTS
VIRTUAL:X
auswählen.
PAIR
–
STANDARD
Gibt den Originalton aus.
–
SURROUND SOUND
VOL
BASS
BASS
–
Standard.
GAME PRO
Liefert einen stereoskopischen Sound, der
Sie beim Spielen in die Handlung eintauchen lässt.
–
ADAPTIVE SOUND
Analysiert den Inhalt in Echtzeit und stellt automatisch das optimale Schallfeld auf
VOL BASS zur Verfügung.
–
DTS VIRTUAL:X
Immersiver 3D-Sound aus jedem Inhalt.
DEU - 22
VOL
PAIR
SOUND
MODE
Bluetooth
PAIR
•
DRC (Dynamic Range Control)
DRC-Funktion (Dynamic Range Control) auf Dolby Digital-Tracks anwenden. Drücken
Sie die Taste
SOUND MODE
und halten Sie sie gedrückt, während die Soundbar ausgeschaltet ist, um DRC (Dynamic Range Control) ein- oder auszuschalten. Bei aktiviertem DRC wird lauter Ton reduziert. (Der Ton könnte verzerrt werden.)
•
Bluetooth Power
Mit dieser Funktion schaltet sich die Soundbar automatisch ein, wenn sie eine
Verbindungsanfrage von einem zuvor verbundenen Fernseher oder Bluetooth-Gerät erhält. Diese Einstellung ist standardmäßig eingeschaltet.
– Halten Sie die Taste
SOUND MODE
für mindestens 5 Sekunden gedrückt, um die
Bluetooth Power-Funktion auszuschalten.
Drücken Sie die
PAIR
-Taste. Im Soundbar-Display wird „
BT PAIRING
“ angezeigt.
In diesem Modus können Sie die Soundbar mit einem neuen Bluetooth-Gerät verbinden, indem Sie die Soundbar aus der Bluetooth-Gerätesuchliste auswählen.
Drücken Sie die
p
-Taste, um eine Musikdatei vorübergehend anzuhalten.
Wenn Sie die Taste erneut drücken, wird die Musikdatei wiedergegeben.
Wiedergabe /
Pause
BASS
PAIR
SOUND
MODE
Oben/Unten/
VOL
VOL
Drücken Sie die angegebenen Bereiche zum Auswählen von
Oben/Unten/Links/Rechts.
BASS
BASS
Drücken Sie Oben/Unten/Links/Rechts auf der Taste zum Auswählen oder Einstellen von
Funktionen.
•
Wiederholen
Zum Verwenden der Wiederholungsfunktion im „
USB
“-Modus drücken Sie die
Oben
-
Taste.
•
Musiktitel überspringen
Drücken Sie die Taste
Rechts
, um die nächste Musikdatei auszuwählen. Drücken Sie die
Taste
Links
, um die vorherige Musikdatei auszuwählen.
•
ID SET
Drücken und halten Sie die Taste
Oben
für 5 Sekunden gedrückt, um
ID SET
abzuschließen (beim Verbinden mit einem Zubehörelement).
DEU - 23
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
•
Lautstärkebeschränkungsfunktion
Um Ihr Gehör zu schützen, beschränkt die Lautstärkebegrenzungsfunktion die
Lautstärke auf 20, wenn Sie die Soundbar einschalten und die Lautstärke höher als
20 eingestellt ist.
– Der Standardwert für die Lautstärkebegrenzungsfunktion ist Aus. Sie müssen sie einschalten, um sie zu aktivieren.
– Wenn sie eingeschaltet wird, bleibt die Lautstärkebegrenzungsfunktion auch dann eingeschaltet, wenn die Stromversorgung ausgeschaltet wird.
– Ein- oder Ausschalten der Lautstärkebegrenzungsfunktion halten Sie die Taste
Unten
an der Fernbedienung 5 Sekunden lang gedrückt. Bei ausgeschalteter
Lautstärkebegrenzungsfunktion erscheint „
V FREE
“ in der vorderen Anzeige.
Bei eingeschalteter Funktion erscheint „
V LOCK
“.
Klangsteuerung
SOUND
MODE
PAIR
Sie können unter
TREBLE
,
BASS
, oder
AUDIO SYNC
auswählen.
• Um die Lautstärke der Höhen oder des Basses zu regeln, drücken Sie die Taste
Klangsteuerung
, um
TREBLE
oder
BASS
auszuwählen und passen Sie dann die
Lautstärke mit den
Oben/Unten
-Tasten zwischen -6~+6 an.
• Drücken Sie die Taste
(Klangsteuerung)
und halten Sie sie ca. 5 Sekunden lang gedrückt, um den Klang für jedes Frequenzband anzupassen. 150Hz, 300Hz, 600Hz,
1,2kHz, 2,5kHz, 5kHz und 10kHz sind durch Verwendung der Tasten
Links/Rechts
wählbar und können mit den Tasten
Oben/Unten
auf eine Einstellung zwischen
-6 bis +6 eingestellt werden.
• Falls das Video auf dem Fernseher und der Ton der Soundbar nicht synchron sind, drücken Sie die
Klangsteuerung
-Taste, um
AUDIO SYNC
auszuwählen und stellen Sie dann mit den
Oben/Unten
-Tasten die Audioverzögerung zwischen 0~300 Millisekunden ein. (Nicht verfügbar im „
USB
“- oder „
BT
“-Modus.)
• Wenn die Sourroundlautsprecher angeschlossen sind, kann die Rücklautsprecher-
Funktion auf EIN/AUS gestellt werden, indem die
Oben/Unten
-Tasten verwendet werden, um die Lautstärke in einem Bereich von -6 bis +6 einzustellen.
•
AUDIO SYNC
wird nur bei einigen Funktionen unterstützt.
PAIR
VOL
SOU
ND
MO
DE
VOL
WOOFE
R
SOUND
MODE
SOUND
MODE
PAIR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Bewegen Sie die
WOOFER
-Taste vor oder zurück, um die Lautstärke des Tieftöners auf -12 oder von -6 bis +6 einzustellen. Um die Lautstärke des Subwoofers auf 0 zu stellen, drücken
Sie die Taste.
VOL
VOL
BASS
BASS
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Bewegen Sie die
VOL
-Taste vor oder zurück, um die Lautstärke einzustellen.
•
Stummschaltung
Drücken Sie die Taste
VOL
, um den Ton stumm zu schalten. Drücken Sie sie erneut, um den Ton wieder einzuschalten.
DEU - 24
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Anpassen der Soundbar-Lautstärke mit einer TV-Fernbedienung
Bei einem Samsung TV kann die Lautstärke der Soundbar mit der IR-Fernbedienung, die im Lieferumfang des Samsung TV enthalten ist, eingestellt werden.
Stellen Sie zuerst den Fernsehton im TV-Menü Ihres
Samsung TV auf externe Lautsprecher, und verwenden Sie dann die Samsung-Fernbedienung, um die Lautstärke der Soundbar zu einzustellen. Weitere
Informationen finden Sie im Benutzerhandbuch des
Fernsehgeräts. Standardmäßig wird diese Funktion von der Fernbedienung des Samsung TV gesteuert.
Wenn es sich bei Ihrem Fernsehgerät nicht um einen
Samsung TV handelt, befolgen Sie die nachstehenden
Anweisungen, um die Einstellungen dieser Funktion zu ändern.
1.
Schalten Sie die Soundbar aus.
BYE
2.
Wenn Sie diese Funktion nicht verwenden möchten, drücken Sie die Taste
WOOFER
nach oben und halten Sie sie für 5 Sekunden wiederholt gedrückt, bis „
OFF-TV REMOTE
“ in der Anzeige erscheint.
4.
Wenn Sie die Soundbar in den
Standardmodus zurücksetzen möchten
(Steuerung über eine Samsung-TV-
Fernbedienung), drücken Sie die Taste
WOOFER
nach oben und halten Sie sie für 5
Sekunden wiederholt gedrückt, bis
„
SAMSUNG-TV REMOTE
“in der Anzeige erscheint.
SOU
ND
MO
DE
5 Sec
VOL
WOOFE
R
SOUNDB
AR
(Standardmodus)
SAMSUNG-TV REMOTE
– Jedes Mal, wenn Sie die
WOOFER
-Taste nach oben drücken und für mindestens
5 Sekunden gedrückt halten, ändert sich der Modus in der folgender Reihenfolge:
„
SAMSUNG-TV REMOTE
“
(Standardmodus) → „
OFF-TV REMOTE
“ →
„
ALL-TV REMOTE
“.
– Diese Funktion ist je nach Fernbedienung eventuell nicht verfügbar.
– Diese Funktion wird von den folgenden
Herstellern unterstützt:
VIZIO, LG, Sony, Sharp, PHILIPS,
PANASONIC, TOSHIBA, Hisense, RCA
SOU
ND
MO
DE
5 Sec OFF-TV REMOTE
VOL
WOOFE
R
SOUNDB
AR
3.
Wenn Sie die Soundbar mit der
Fernbedienung Ihres Fernsehers steuern wollen, drücken Sie wiederholt die Taste
WOOFER
nach oben und halten Sie sie für 5
Sekunden gedrückt, bis „
ALL-TV REMOTE
“ in der Anzeige erscheint. Verwenden Sie dann das Menü Ihres Fernsehers, um externe
Lautsprecher auszuwählen.
5 Sec
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
ALL-TV REMOTE
DEU - 25
Verwenden der verborgenen Tasten (Tasten mit mehr als einer funktion)
Fernbedienungstaste
WOOFER (Oben)
p
(Wiedergabe / Pause)
Verborgene Taste
Funktion
TV-Fernbedienung Ein/Aus (Standby)
Links
Oben
Unten
(Klangsteuerung)
Initialisieren (Standby)
Automatische TV-Verbindung Ein/Aus
(BT Bereit)
ID SET (Standby)
Lautstärkebeschränkung Ein/Aus
(Standby)
7 Band EQ
DRC ON/OFF (Standby)
SOUND MODE
Bluetooth Power
Referenzseite
Ausgabe-spezifikationen für die unterschiedlichen sound-effektmodi
Surround
VOL
SOUND
MODE
Effekt
STANDARD
Bluetooth
POWER
SURROUND
SOUND
SOUND MODE
GAME PRO
ADAPTIVE
SOUND
WOOFER
DTS VIRTUAL:X
Eingang
2.0 Kanal
5.1 Kanal
2.0 Kanal
5.1 Kanal
2.0 Kanal
5.1 Kanal
2.0 Kanal
5.1 Kanal
2.0 Kanal
5.1 Kanal
Ohne drahtloses
Rücklautsprecherkit
2.1 Kanal
3.1 Kanal
4.1 Kanal
5.1 Kanal
4.1 Kanal
5.1 Kanal
4.1 Kanal
5.1 Kanal
3.1 Kanal
3.1 Kanal
Ausgang
Mit drahtlosem
Rücklautsprecherkit
4.1 Kanal
5.1 Kanal
6.1 Kanal
7.1 Kanal
6.1 Kanal
7.1 Kanal
6.1 Kanal
7.1 Kanal
5.1 Kanal
5.1 Kanal
• Das drahtlose Rücklautsprecherkit von Samsung ist separat erhältlich. Für den Erwerb eines Kits kontaktieren Sie den Händler, bei dem Sie die Soundbar erworben haben.
DEU - 26
09 INSTALLIEREN DER
WANDHALTERUNG
Komponenten für die
Anbringung an der Wand
Vorsichtsmaßnahmen für die
Installation
• Installieren Sie nur an einer vertikalen Wand.
• Installieren Sie nicht an einem Ort mit hoher
Temperatur oder Feuchtigkeit.
• Überprüfen Sie, ob die Wand stark genug ist, um das Gewicht des Produkts zu tragen. Falls nicht, verstärken Sie die Wand oder wählen
Sie einen anderen Installationsort.
• Kaufen und verwenden Sie
Befestigungsschrauben oder Verankerungen, die für Ihre Wandart geeignet sind
(Gipskartonplatte, Eisenplatte, Holz, etc.).
Fixieren Sie die Befestigungsschrauben falls möglich mit Wandverankerungen.
• Kaufen Sie Schrauben für die Wandmontage entsprechend der Art und der Dicke der
Wand, an der Sie die Soundbar montieren wollen.
– Durchmesser: M5
– Länge: 35 mm oder länger empfohlen.
• Schließen Sie die Kabel vom Gerät an externe
Geräte an, bevor sie die Soundbar an der
Wand installieren.
• Stellen Sie sicher, dass das Gerät ausgeschaltet und der Netzstecker gezogen ist, bevor Sie es installieren. Andernfalls kann es zu einem elektrischen Schlag kommen.
Montagehilfe für die Wandhalterung
x 2
Aufhängungsschraube
x 2 x 2
Schraube
Wandhalterung
1.
Platzieren Sie die
Montagehilfe für die
Wandhalterung
an der Wand.
• Die
Montagehilfe für die Wandhalterung
muss waagerecht positioniert sein.
• Falls Ihr Fernseher an der Wand befestigt ist, installieren Sie die Soundbar mindestens 5 cm unterhalb des
Fernsehers.
5 cm oder mehr
DEU - 27
2.
Richten Sie die
Mittellinie der Montagehilfe für die Wandhalterung
auf die Mitte des
Fernsehers aus (wenn Sie die Soundbar unter dem Fernseher montieren) und befestigen
Sie dann die
Montagehilfe für die
Wandhalterung
mit Klebeband an der Wand.
• Wenn Sie die Soundbar nicht unter einem
Fernseher montieren, stellen Sie sicher, dass sich die
Mittellinie
in der Mitte des
Montagebereichs befindet.
5.
Stecken Sie eine Schraube (nicht enthalten) durch jede
Aufhängungsschraube
und drehen Sie dann jede Schraube in einem
Aufhängungsschraubenloch.
6.
Installieren Sie 2
Wandhalterung
mit der richtigen Ausrichtung auf der Unterseite der
Soundbar unter Verwendung von 2
Schrauben
.
Mittellinie
3.
Drücken Sie die Spitze eines Stifts oder einen spitzen Bleistift durch die Mitte der
A-TYPE
-
Bilder an beiden Enden der Montagehilfe, um die Löcher für die Aufhängungsschrauben zu markieren. Entfernen Sie dann die
Montagehilfe für die Wandhalterung
.
4.
Bohren Sie mit einem geeigneten Bohrer an jeder Markierung ein Loch in die Wand.
• Wenn die Markierungen nicht den
Positionen der Halterungsbolzen entsprechen, achten Sie darauf, geeignete
Dübel oder Molly-Dübel in die Löcher einzuführen, bevor Sie die
Aufhängungsschrauben einführen. Wenn
Sie Dübel oder Molly-Dübel verwenden, achten Sie darauf, dass die gebohrten
Löcher für die verwendeten Dübel oder
Molly-Dübel groß genug sind.
DEU - 28
• Achten Sie beim Zusammenbau darauf, dass sich die Aufhängungsteile der
Wandhalterungen
hinter der Rückseite der Soundbar befinden.
Rückseite der Soundbar
Rechtes Ende der Soundbar
7.
Montieren Sie die Soundbar mithilfe der befestigten
Wandhalterungen
, indem Sie die
Wandhalterungen
an die
Aufhängungsschrauben
an der Wand hängen.
10 PLATZIEREN DER
SOUNDBAR AUF
EINEM TV-
STÄNDER
Platzieren Sie die Soundbar auf einen TV-Ständer.
8.
Schieben Sie die Soundbar wie nachfolgend dargestellt nach unten, sodass die
Wandhalterung
sicher auf den
Aufhängungsschraube
ruhen.
• Setzen Sie die
Aufhängungsschraube
in den breiten (unteren) Teil der
Wandhalterung
ein und schieben Sie dann die
Wandhalterung
nach unten, sodass die
Wandhalterung
sicher auf den
Aufhängungsschraube
ruhen.
3 cm o der m ehr
Richten Sie wie auf der Abbildung dargestellt die
Mitte der Soundbar auf die Mitte des Fernsehers aus und positionieren Sie die Soundbar vorsichtig auf dem Fernsehständer.
Für eine optimale Tonqualität positionieren Sie die
Soundbar mindestens 3 cm von der TV-
Vorderseite entfernt.
HINWEIS
• Achten Sie darauf, dass die Soundbar auf einer flachen und stabilen Oberfläche platziert ist.
DEU - 29
11 SOFTWAREAKTUALISIERUNG
Samsung kann in Zukunft Aktualisierungen für das Firmwaresystem der Soundbar anbieten.
USB-Anschluss
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
Wenn eine Aktualisierung angeboten wird, können Sie die Firmware aktualisieren, indem Sie ein USB-Gerät mit der darauf gespeicherten
Firmware-Aktualisierung an den USB-Anschluss der Soundbar anschließen. Weitere Informationen zum Herunterladen der Aktualisierungsdateien finden Sie auf der Samsung Webseite unter
(www.samsung.com→Support).
Wählen Sie dann den Produkttyp oder geben Sie die Modellnummer Ihrer Soundbar ein, wählen Sie die Option Software & Apps und dann Downloads.
Beachten Sie, dass die Namen der Option variieren können.
Updateverfahren
Wichtig:
Die Aktualisierungsfunktion löscht alle
Benutzereinstellungen. Wir empfehlen Ihnen, Ihre
Einstellungen aufzuschreiben, damit Sie sie nach der
Aktualisierung einfach wieder einstellen können.
Beachten Sie, dass das Aktualisieren der Firmware auch den Subwoofer-Anschluss zurücksetzt.
1.
Schließen Sie einen USB-Stick an den
USB-Anschluss Ihres Computers an.
Wichtig:
Stellen Sie sicher, dass sich keine
Musikdateien auf dem USB-Stick befinden.
Dies kann dazu führen, dass das Firmware-
Update fehlschlägt.
2.
Gehen Sie auf die Samsung-Website unter
(samsung.com)
wählen Sie Modellnummer eingeben und geben Sie das Modell Ihrer
Soundbar ein. Wählen Sie Handbücher und
Downloads und laden Sie die neueste
Softwaredatei herunter.
3.
Speichern Sie die heruntergeladene Software auf einem USB-Speicher und wählen Sie „Hier extrahieren“, um den Ordner zu entzippen.
4.
Schalten Sie die Soundbar aus und schließen Sie den USB-Stick mit dem Software-Update an den USB-Anschluss an.
5.
Schalten Sie die Soundbar ein. Innerhalb von
3 Minuten wird „
UPDATE
“ angezeigt und der
Aktualisierungsprozess beginnt.
6.
Wenn das Update abgeschlossen ist, wird die
Soundbar ausgeschaltet. Halten Sie die Taste
p
auf der Fernbedienung 5 Sekunden lang gedrückt. „
INIT
“ wird auf dem Bildschirm angezeigt und die Soundbar wird ausgeschaltet. Das Update ist abgeschlossen.
• Dieses Produkt verfügt über eine DUAL-
BOOT-Funktion. Wenn die Firmware nicht aktualisiert werden kann, können Sie sie erneut aktualisieren.
7.
Stellen Sie Ihre Einstellungen an der
Soundbar wieder her.
DEU - 30
Wenn UPDATE nicht angezeigt wird
1.
Schalten Sie die Soundbar aus, trennen Sie das Speichergerät mit den Update-Dateien und verbinden Sie es anschließend erneut mit dem USB-Anschluss der Soundbar.
2.
Ziehen Sie das Stromkabel der Soundbar ab, schließen Sie es erneut an und schalten Sie dann die Soundbar ein.
HINWEISE
• Das Aktualisieren der Firmware funktioniert gegebenenfalls nicht richtig, wenn von der
Soundbar unterstützte Audiodateien auf dem
Speichergerät gespeichert sind.
• Unterbrechen Sie während des
Aktualisierungsprozesses nicht die
Stromversorgung und entfernen Sie nicht den
USB-Speicher. Wenn die Aktualisierung der
Firmware abgeschlossen ist, wird das
Hauptgerät automatisch ausgeschaltet.
• Nach Abschluss der Aktualisierung wird die
Benutzerkonfiguration in der Soundbar initialisiert, so dass Sie Ihre Einstellungen wieder einstellen können. Wir empfehlen Ihnen,
Ihre persönlichen Einstellungen schriftlich zu notieren, damit Sie sie nach dem Update leicht wiederherstellen können.
Beachten Sie, dass durch die Aktualisierung der
Firmware auch die Subwoofer-Verbindung zurückgesetzt wird.
Wenn die Verbindung zum Subwoofer nach dem Update nicht automatisch
wiederhergestellt wird, siehe Seite 6.
Wenn das Software-Update fehlschlägt, prüfen
Sie, ob der USB-Speicher defekt ist.
• Benutzer von Mac OS sollten als USB-Format
MS-DOS (FAT) verwenden.
• Abhängig vom Hersteller des Speichergeräts ist eine Aktualisierung über USB gegebenenfalls nicht verfügbar.
DEU - 31
12 FEHLERBEHEBUNG
Bevor Sie sich an den Kundendienst wenden, überprüfen Sie bitte die folgenden Punkte.
Das Gerät wird nicht eingeschaltet.
Ist das Netzkabel fest mit der Steckdose und dem Netzteil verbunden?
;
Ziehen Sie das Netzkabel aus der Steckdose und dem Netzteil heraus und schließen Sie es wieder an, um eine sichere Verbindung zu gewährleisten.
Ist das Netzteil fest mit dem Hauptgerät verbunden?
;
Trennen Sie das Netzteil von der Soundbar und schließen Wie es wieder an, um eine feste und sichere Verbindung zu gewährleisten.
Eine Funktion funktioniert nicht, wenn die
Taste gedrückt wird.
Gibt es statische Elektrizität in der Luft?
;
Trennen Sie den Netzstecker und schließen
Sie ihn erneut an.
Im BT-Modus kommt es zu Tonaussetzern.
;
Siehe die Abschnitte zur Bluetooth-
Verbindung auf Seite 13 und 18.
Es wird kein Ton wiedergegeben.
Ist die Stummschaltfunktion aktiviert?
;
Drücken Sie die Taste
(
Stummschaltung
), um die
Stummschaltfunktion zu deaktivieren.
Ist die Lautstärke auf das Minimum eingestellt?
;
Passen Sie die Lautstärke an.
Die Fernbedienung funktioniert nicht.
Sind die Batterien leer?
;
Tauschen Sie sie gegen neue aus.
Ist der Abstand zwischen Fernbedienung und
Soundbar-Hauptgerät zu groß?
;
Gehen Sie mit der Fernbedienung näher an das Soundbar-Hauptgerät heran.
Die rote LED am Subwoofer blinkt und der
Subwoofer gibt keinen Ton aus.
Dieses Problem kann auftreten, wenn der
Subwoofer nicht an das Soundbar-Hauptgerät angeschlossen ist.
;
Versuchen Sie, den Subwoofer erneut zu
Der Subwoofer brummt und vibriert spürbar.
Versuchen Sie, die Vibration Ihres Subwoofers anzupassen.
;
Bewegen Sie die
WOOFER
-Taste an Ihrer
Fernbedienung vor oder zurück, um den
Subwoofer-Pegel einzustellen. (bis -12 oder zwischen -6 ~ +6).
DEU - 32
13 LIZENZ 14 BEKANNTMACHUNG
ZU OPEN SOURCE
LIZENZEN
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
Wenn Sie Fragen bezüglich des Themas Open
Source haben, wenden Sie sich bitte per E-Mail unter der Adresse an Samsung
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol together, Digital Surround, and the Digital Surround logo are registered trademarks or trademarks of
DTS, Inc. in the United States and/or other countries.
© DTS, Inc. All Rights Reserved.
15 WICHTIGE
HINWEISE ZUM
KUNDENDIENST
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol together, Virtual:X, and the DTS Virtual:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc.
All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
• Die Abbildungen in dieser Anleitung dienen nur als Referenz und können sich vom aktuellen Produkt unterscheiden.
• Es kann eine Gebühr erhoben werden, wenn:
(a) Ein Techniker auf Ihre Anfrage bestellt wird und am Gerät kein Defekt vorliegt
(z. B. weil Sie diese Bedienungsanleitung nicht gelesen haben).
(b) Sie das Gerät in einer Reparaturwerkstatt abgegeben haben und am Gerät kein
Defekt vorliegt
(z. B. weil Sie diese Bedienungsanleitung nicht gelesen haben).
• Die Höhe dieser Gebühr wird Ihnen mitgeteilt, bevor irgendwelche Arbeiten durchgeführt werden oder der Hausbesuch erfolgt.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Samsung Electronics Co.,
Ltd. is under license. Other trademarks and trade names are those of their respective owners.
DEU - 33
16 SPEZIFIKATIONEN UND LEITFADEN
Technische daten
Modellname
USB
Gewicht
Abmessungen (B × H × T)
Betriebstemperatur
Zulässige Luftfeuchtigkeit
VERSTÄRKER
Nennausgangsleistung
Unterstützte Wiedergabeformate
AUSGANGSLEISTUNG DES DRAHTLOSGERÄTS
BT max. Transmitterleistung
SRD max. Transmitterleistung
HW-Q60T
5V/0,5A
3,4 kg
980,0 x 58,0 x 105,0 mm
+5°C bis +35°C
10 % ~ 75 %
30W x 6 + 10W x 2
LPCM 2ch, Dolby Audio™
(unterstützt Dolby® Digital), DTS, DTS Virtual:X
6mW bei 2,402GHz - 2,480GHz
25mW bei 5,725GHz – 5,825GHz
Subwoofername
Gewicht
Abmessungen (B × H × T)
VERSTÄRKER
Nennausgangsleistung
AUSGANGSLEISTUNG DES DRAHTLOSGERÄTS
SRD max. Transmitterleistung
PS-WR65BB
6,2 kg
205,0 x 353,0 x 303,2 mm
160W
25mW bei 5,725GHz – 5,825GHz
Gesamtstromverbrauch im Bereitschaftszustand (W)
Bluetooth
Anschlussdeaktivierungsmethode
2,0W
Halten Sie die Taste
SOUND MODE
für mindestens 5 Sekunden gedrückt, um die
Bluetooth Power-Funktion auszuschalten.
HINWEISE
• Samsung Electronics Co., Ltd behält sich das Recht auf unangekündigte Änderungen vor.
• Gewicht und Abmessungen können von den Angaben abweichen.
DEU - 34
• Samsung erklärt hiermit, dass dieses Gerät der Richtlinie
2014/53/EU entspricht.
Der vollständige Text der EU-Konformitätserklärung ist unter folgender
Internetadresse abrufbar: http://www.samsung.com geben Sie unter Support >
Produktsupport suchen den Modellnamen ein.
Dieses Gerät kann in allen EU-Ländern betrieben werden.
[Korrekte Entsorgung der Batterien dieses Produkts]
(Gilt für Länder mit Abfalltrennsystemen)
Die Kennzeichnung auf der Batterie bzw. auf der dazugehörigen Dokumentation oder Verpackung gibt an, dass die Batterie zu diesem Produkt nach seiner Lebensdauer nicht zusammen mit dem normalen
Haushaltsmüll entsorgt werden darf. Wenn die Batterie mit den chemischen Symbolen Hg, Cd oder Pb gekennzeichnet ist, liegt der Quecksilber-, Cadmium- oder Blei-Gehalt der Batterie über den in der EG-
Richtlinie 2006/66 festgelegten Referenzwerten. Wenn Batterien nicht ordnungsgemäß entsorgt werden, können sie der menschlichen Gesundheit bzw. der Umwelt schaden.
Bitte helfen Sie, die natürlichen Ressourcen zu schützen und die nachhaltige Wiederverwertung von stofflichen Ressourcen zu fördern, indem Sie die Batterien von anderen Abfällen getrennt über Ihr örtliches kostenloses Altbatterie- Rücknahmesystem entsorgen.
Korrekte Entsorgung von Altgeräten
(Elektroschrott)
(Gilt für Länder mit Abfalltrennsystemen)
Die Kennzeichnung auf dem Produkt, Zubehörteilen bzw. auf der dazugehörigen Dokumentation gibt an, dass das Produkt und Zubehörteile (z. B. Ladegerät,Kopfhörer, USB-Kabel) nach ihrer Lebensdauer nicht zusammen mit dem normalen Haushaltsmüll entsorgt werden dürfen. Entsorgen Sie dieses Gerät und
Zubehörteile bitte getrennt von anderen Abfällen, um der Umwelt bzw. der menschlichen Gesundheit nicht durch unkontrollierte Müllbeseitigung zu schaden. Helfen Sie mit, das Altgerät und Zubehörteile fachgerecht zu entsorgen, um die nachhaltige Wiederverwertung von stofflichen Ressourcen zu fördern.
Private Nutzer wenden sich an den Händler, bei dem das Produkt gekauft wurde, oder kontaktieren die zuständigen Behörden, um in Erfahrung zu bringen, wo Sie das Altgerät bzw. Zubehörteile für eine umweltfreundliche Entsorgung abgeben können.
Gewerbliche Nutzer wenden sich an ihren Lieferanten und gehen nach den Bedingungen des
Verkaufsvertrags vor. Dieses Produkt und elektronische Zubehörteile dürfen nicht zusammen mit anderem
Gewerbemüll entsorgt werden.
Für Informationen über die Umweltverpflichtungen und produktspezifischen regulatorischen
Verpflichtungen von Samsung wie z. B. REACH, WEEE, Batterien, besuchen Sie: http://www.samsung.com/uk/aboutsamsung/samsungelectronics/corporatecitizenship/data_corner.html
VERORDNUNG (EU) 2019/1782 DER KOMMISSION
Ökodesign-Anforderungen an externe Netzteile www.samsung.com/global/ecodesign_component
DEU - 35
INFORMATIONS RELATIVES À LA SÉCURITÉ
AVERTISSEMENTS
POUR ÉVITER LES RISQUES DE CHOC
ÉLECTRIQUE, NE DÉMONTEZ PAS LE CAPOT.
L’APPAREIL NE CONTIENT PAS DE PIÈCES
RÉPARABLES PAR L’UTILISATEUR ; S’ADRESSER
À UN SERVICE APRÈS-VENTE QUALIFIÉ.
Reportez-vous au tableau ci-dessous pour une explication des symboles pouvant figurer sur votre produit Samsung.
ATTENTION
RISQUE DE CHOC
ÉLECTRIQUE. NE PAS
OUVRIR
Ce symbole indique que ce produit est alimenté par haute tension. Il est dangereux de toucher la moindre pièce située à l'intérieur de ce produit.
Ce symbole indique qu'une documentation importante relative au fonctionnement et à l'entretien est fournie avec le produit.
Produit de classe II : ce symbole indique qu'aucun branchement de sécurité à la terre (prise de terre) n'est requis.
Si ce symbole n'est pas présent sur un produit avec un cordon d'alimentation, le produit DOIT avoir une connexion de protection fiable à la terre.
Tension CA : ce symbole indique que la tension nominale indiquée par le symbole est une tension CA.
Tension CC : ce symbole indique que la tension nominale indiquée par le symbole est une tension CC.
Mise en garde, Consulter le mode d'emploi : ce symbole avertit l'utilisateur qu'il doit consulter le manuel d'utilisation pour en savoir plus sur les informations relatives à la sécurité.
FRA - ii
AVERTISSEMENT
• Afin de diminuer les risques d’incendie ou de choc électrique, n’exposez pas cet appareil à la pluie ou à l’ humidité.
ATTENTION
• POUR PRÉVENIR LES CHOCS ÉLECTRIQUES,
BRANCHEZ LA FICHE AU FOND, EN
PRENANT SOIN D’INSÉRER LA TIGE LARGE
DANS LA FENTE LARGE.
• Cet appareil doit toujours être branché à une prise terre.
• Pour déconnecter l’appareil du circuit principal, la prise doit être débranchée de la prise principale ; il est de ce fait nécessaire que la prise principale soit facile d’accès.
• Évitez toute projection d’eau sur l’appareil.
Ne posez jamais d’objet contenant un liquide
(ex : un vase) dessus.
• Pour éteindre complètement l’appareil, vous devez retirer le cordon d’alimentation de la prise murale. Par conséquent, le cordon d’alimentation doit être facilement accessible
à tout moment.
PRÉCAUTIONS
1.
Vérifiez que l’alimentation électrique CA de votre domicile respecte les conditions en matière d’alimentation répertoriées sur l’étiquette d’identification située au bas de votre produit. Posez votre produit à plat sur un meuble stable en veillant à laisser un espace de 7 à 10 cm autour de l’appareil afin d’assurer une ventilation correcte de celui-ci.
Faites attention à ne pas obstruer les orifices de ventilation. Ne posez pas l’ensemble sur un amplificateur ou un autre appareil susceptible de chauffer. Cet ensemble est conçu pour une utilisation en continu. Pour entièrement éteindre l’appareil, débranchez la fiche CA de la prise murale. Débranchez l’appareil si vous envisagez de ne pas l’utiliser durant une longue période.
2.
En cas d’orage, débranchez la fiche de l’appareil de la prise murale. Les surtensions occasionnées par l’orage pourraient endommager votre appareil.
3.
N’exposez pas l’ensemble aux rayons directs du soleil ou à toute autre source de chaleur.
Ceci pourrait entraîner une surchauffe et un dysfonctionnement de l’appareil.
4.
Protégez le produit de l’humidité (comme les vases) et d’une chaleur excessive (comme une cheminée) ou de tout équipement capable de créer des champs magnétiques ou électriques. Débranchez le câble d’alimentation en cas de dysfonctionnement.
Votre produit n’est pas prévu pour un usage industriel. Ce produit ne peut être utilisé qu’à des fins personnelles. Une condensation peut se former si le produit ou un disque a
été stocké à basse température.
Si vous devez transporter l’ensemble pendant l’hiver, attendez environ 2 heures que l’appareil ait atteint la température de la pièce avant de l’utiliser.
FRA - iii
5.
Les piles utilisées dans ce produit peuvent contenir des produits ch miques dangereux pour l’environnement. Ne jetez pas les piles dans votre poubelle habituelle. Ne vous débarrassez pas des piles en les faisant brûler. Ne court-circuitez pas, ne désassemblez pas ni ne faites pas surchauffer les batteries. Le remplacement incorrect de la batterie entraîne un risque d’explosion. Ne la remplacez que par une batterie du même type.
À PROPOS DE CE
MANUEL
Le manuel d’utilisateur est composé de deux parties : ce MANUEL D’UTILISATEUR sur papier et un MANUEL COMPLET détaillé à télécharger.
MANUEL D’UTILISATEUR
Consultez ce manuel pour en savoir plus sur les consignes de sécurité, l’installation du produit, les connexions et les spécifications du produit.
MANUEL COMPLET
Vous pouvez accéder au MANUEL COMPLET sur le centre d’assistance clientèle en ligne de
Samsung ou en scannant le code QR.
Pour consulter le manuel sur votre PC ou appareil mobile, téléchargez-le au format document depuis le site Web de Samsung.
(http://www.samsung.com/support)
La présentation et les spécifications peuvent faire l'objet de modifications sans préavis.
SOMMAIRE
01 Contrôle des Composants 2
02 Présentation du Produit 3
Panneau frontal/supérieur de la Soundbar
Panneau inférieur de la Soundbar
03 Connexion de la Soundbar
5
Connexion de l’alimentation électrique
Connexion de la Soundbar au Caisson de basse
– Connexion automatique entre le Caisson de basse et la Soundbar
– Connexion manuelle du Caisson de basse si la connexion automatique échoue
Connexion du SWA-8500S (Vendue séparément) à une Soundbar
04 Connexion à votre Téléviseur 10
Méthode 1. Connexion avec un câble
– Connexion d’un téléviseur à l’aide d’un câble HDMI
– Connexion à l’aide d’un câble optique
– Connexion à un téléviseur via Bluetooth
05 Connexion à un Appareil Externe
15
Connexion à l’aide d’un câble HDMI
Connexion à l’aide d’un câble optique
06 Connexion d’un périphérique de stockage USB
17
FRA - iv
FRA - v
01 CONTRÔLE DES COMPOSANTS
PAIR
VOL WOOFER
SOUNDBAR
Unité principale Soundbar Caisson de basse Télécommande/Piles
x 2
Cordon d’alimentation
(Caisson de basse, Soundbar)
Adaptateur CA/CC
(Soundbar)
Câble HDMI
Guide de fixation murale
x 2
Vis de fixation
x 2
Support de fixation murale
Vis
x 2
• Pour plus d’informations sur l’alimentation et la consommation électriques, reportez-vous à l’étiquette collée sur le produit. (Étiquette : Bas de l’Unité Principale Soundbar)
• Pour acheter des composants supplémentaires ou des câbles optionnels, contactez un Centre de service Samsung ou le Service client de Samsung.
• L’aspect des accessoires peut légèrement différer des illustrations ci-dessus.
Insertion des piles avant l’utilisation de la télécommande (Piles AA X 2)
Faites glisser le couvercle arrière dans la direction de la flèche jusqu’à ce qu’il soit complètement retiré. Insérez 2 piles AA (1,5 V) orientées de sorte que la polarité soit correcte. Remettez le couvercle arrière en le faisant glisser dans sa position.
FRA - 2
02 PRÉSENTATION DU PRODUIT
Panneau frontal/supérieur de la Soundbar
Placez le produit de sorte que le logo SAMSUNG se trouve sur le dessus.
Panneau supérieur
Affichage
Affiche l'état et le mode actuel du produit.
Touche (Alimentation)
Allume et éteint l'appareil.
•
Fonction Auto Power Down
L’appareil s’éteint automatiquement dans les situations suivantes.
– Mode
D.IN
/
HDMI
/
BT
/
USB
: S’il n’y a pas de signal audio pendant 20 minutes.
Touche -/+ (Volume)
Règle le volume.
• Une fois ajusté, le niveau de volume apparaît sur l’affichage avant de la Soundbar.
Touche
(
Source)
Sélectionne le mode d'entrée de la source.
Mode d’entrée
Entrée numérique optique
Entrée ARC (HDMI OUT)
Entrée HDMI
Mode BLUETOOTH
Mode USB
D.IN
Affichage
D.IN
TV ARC (Conversion automatique)
HDMI
BT
USB
• Pour activer le mode «
BT PAIRING
», changez la source sur le mode «
BT
», puis appuyez et maintenez enfoncée la touche
(Source)
pendant plus de 5 secondes.
• Lorsque vous branchez le cordon CA, la touche Marche/Arrêt fonctionne pendant 4 à 6 secondes.
• Lorsque vous mettez l’unité sous tension, il faut compter 4 ou 5 secondes de retard avant le déclenchement du son.
• Si vous souhaitez bénéficier du son du Soundbar uniquement, vous devrez éteindre les enceintes du téléviseur depuis le menu Audio Setup de votre téléviseur. Reportezvous au manuel fourni avec votre téléviseur.
FRA - 3
Panneau inférieur de la Soundbar
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
Permet de connecter un périphérique USB pour lire des fichiers musicaux sur le périphérique USB via la
Soundbar.
DC 24V (Entrée d'alimentation électrique)
Permet de connecter l'adaptateur CA/CC.
HDMI
Permet l'entrée de signaux numériques vidéo et audio simultanément à l'aide du câble HDMI.
Permet de connecter la sortie HDMI d'un appareil externe.
HDMI TO TV (ARC)
Permet de connecter une prise jack HDMI (ARC) sur un téléviseur.
DIGITAL AUDIO IN (OPTICAL)
Permet de connecter la sortie numérique (optique) d'un appareil externe.
• Lorsque vous débranchez le câble d’alimentation de l’adaptateur d’alimentation CA/CC d’une prise de courant murale, retirez la fiche. Ne tirez pas le câble.
• Ne branchez pas cette unité ou d’autres composants à une prise CA tant que toutes les connexions entre les composants ne sont pas terminées.
FRA - 4
03 CONNEXION DE LA SOUNDBAR
Connexion de l’alimentation électrique
Utilisez les composants d’alimentation pour connecter le Caisson de basse et la Soundbar à une prise
électrique dans l’ordre suivant :
1.
Connectez le cordon d’alimentation au Caisson de basse.
2.
Branchez le câble de sortie d’alimentation sur l’adaptateur secteur, puis à la Soundbar.
3.
Connectez le cordon d’alimentation à la prise murale.
Reportez-vous aux illustrations ci-dessous.
• Pour plus d’informations sur l’alimentation et la consommation électriques requises, reportez-vous
à l’étiquette collée sur le produit. (Étiquette : Partie inférieure de l’unité principale Soundbar)
POWER
Cordon d’alimentation
Cordon d’alimentation
Connexion de l’alimentation
électrique
DC 24V
Arrière du
Caisson de basse
Connexion de l’alimentation
électrique
Adaptateur CA/CC
USB (5V 0.5A)
DC 24V
Partie inférieure de l’unité principale
Soundbar
• Veillez à poser l’adaptateur CA/CC à plat sur une table ou sur le sol. Si l’adaptateur CA/CC pend et que l’entrée du cordon CA est située face vers le haut, de l’eau ou d’autres substances étrangères risquent de pénétrer dans l’adaptateur et d’entraîner des dysfonctionnements.
FRA - 5
Connexion de la Soundbar au Caisson de basse
Lorsque le Caisson de basse est connecté, vous pouvez profiter de la puissance sonore des graves.
Connexion automatique entre le Caisson de basse et la Soundbar
Lorsque vous mettez l’appareil sous tension après avoir connecté les câbles d’alimentation à la
Soundbar et au Caisson de basse, le Caisson de basse est automatiquement connecté à la Soundbar.
• Une fois l’appariement automatique effectué, les indicateurs bleus situés à l’arrière du Caisson de basse s’allument.
Témoins indicateurs LED sur l’arrière du Caisson de basse
LED
Bleu
Rouge
Rouge et bleu
État
Activé
Description
Connexion réussie
(fonctionnement normal)
-
Résolution
Clignotement
Activé
Clignotement
Récupération de la connexion
En veille (avec l’unité principale de la Soundbar
éteinte)
Échec de la connexion
Dysfonctionnement
Vérifiez si le câble d’alimentation fixé à l’unité principale Soundbar est connecté correctement ou attendez environ
5 minutes. Si le clignotement continue, essayez de connecter manuellement le
caisson de basse. Voir page 7.
Vérifiez que le câble d’alimentation sur l’unité principale Soundbar est connecté correctement.
Reconnectez. Reportez-vous aux instructions sur la connexion manuelle à
Reportez-vous aux informations de contact du Centre de service Samsung dans le manuel.
FRA - 6
Connexion manuelle du Caisson de basse si la connexion automatique échoue
Avant d’effectuer la procédure de connexion manuelle ci-dessous :
• Vérifiez que les câbles d’alimentation pour la Soundbar et le Caisson de basse sont connectés correctement.
• Assurez-vous que la Soundbar est allumée.
1.
Appuyez sur la touche
ID SET
à l’arrière du Caisson de basse, et maintenez-la enfoncée pendant au moins 5 secondes.
• L’indicateur rouge à l’arrière du Caisson de basse s’éteint et l’indicateur bleu clignote.
5 Sec
Arrière du Caisson de basse
2.
Appuyez sur la touche
Haut
de la télécommande, et maintenez-la enfoncée pendant au moins
5 secondes.
• Le message
ID SET
s’affiche un moment sur l’écran de la Soundbar, avant de disparaître.
• La Soundbar est automatiquement mise sous tension lorsque
ID SET
est terminé.
PAIR
5 Sec
Le logo SAMSUNG est sur le dessus
ID SET
SOUN
D
MOD
E
3.
Vérifiez que le voyant LED LINK s’éclaire en bleu en continu (connexion établie).
Le voyant LED LINK arrête de clignoter et s’éclaire en bleu en continu lorsqu’une connexion est établie entre la Soundbar et le
Caisson de basse sans fil.
Allumé en bleu
FRA - 7
REMARQUES
• Ne branchez pas le cordon d’alimentation de ce produit ou votre téléviseur à une prise de courant murale tant que toutes les connexions entre les composants ne sont pas terminées.
• Avant de déplacer ou d’installer ce produit, assurez-vous de le mettre hors tension et de débrancher le cordon d’alimentation.
• Si l’unité principale est hors tension, le subwoofer sans fil entrera en mode veille et la LED de
STANDBY à l’arrière s’allumera en rouge après avoir clignoté en bleu plusieurs fois.
• Si vous utilisez un appareil qui utilise la même fréquence (5,8 GHz) que la Soundbar près de cette
Soundbar, les interférences peuvent provoquer des interruptions de son.
• La distance de transmission maximale du signal sans fil de l’unité principale est d’environ 10 mètres, mais peut varier en fonction de votre environnement d’exploitation. Si un mur en béton armé ou métallique se trouve entre l’unité principale et le subwoofer sans fil, le système risque de ne pas fonctionner du tout, car le signal sans fil ne peut pas passer à travers le métal.
PRÉCAUTIONS
• Les antennes de réception sans fil sont intégrées au subwoofer sans fil. Gardez les unités à l’abri de l’eau et de l’humidité.
• Pour des performances d’écoute optimales, assurez-vous que la zone autour de l’emplacement du subwoofer sans fil et du module de réception sans fil (vendu séparément) ne présente pas d’obstacles.
Connexion du SWA-8500S (Vendue séparément) à une Soundbar
Passez au vrai son surround sans fil en connectant votre kit d’enceintes arrière sans fil Samsung
(SWA-8500S, vendu séparément) à votre Soundbar.
1.
Connectez le module de réception sans fil à 2 enceintes surround.
– Les câbles d’enceinte répondent à un code couleur.
SURROUND-LEFT
SURROUND-LEFT
L
L R
ID SET
R
SURROUND SPEAKERS OUT
ID SET
SURROUND-RIGHT
SURROUND-RIGHT
FRA - 8
2.
Vérifiez l’état de veille du module de réception sans fil après l’avoir branché à une prise électrique.
• Le voyant LED LINK (LED bleue) situé sur le module de réception sans fil clignote. Si la LED ne clignote pas, appuyez sur la touche
ID SET
au dos du module de réception sans fil avec la pointe d’un stylo pendant 5 à 6 secondes jusqu’à ce que le voyant LED LINK clignote (en bleu). Pour plus d’informations sur la LED, veuillez vous reporter au manuel d’utilisation SWA-8500S.
SURROUND SPEAKERS OUT
R
5 Sec
ID SET
ID SET
STANDBY
LINK
STANDBY
LINK
POWER
Clignotement bleu
POWER
3.
Appuyez sur la touche
Haut
de la télécommande, et maintenez-la enfoncée pendant au moins
5 secondes.
• Le message
ID SET
s’affiche un moment sur l’écran de la Soundbar, avant de disparaître.
• La Soundbar est automatiquement mise sous tension lorsque
ID SET
est terminé.
PAIR
5 Sec
Le logo SAMSUNG est sur le dessus
ID SET
SOUN
D
MOD
E
ATTENTION
• Si votre Soundbar diffuse de la musique au moment où elle est connectée au SWA-8500S, vous pourriez entendre du bruit provenant du woofer une fois la connexion terminée.
4.
Vérifiez que le voyant LED LINK s’éclaire en bleu en continu (connexion établie).
STANDBY
LINK
STANDBY
LINK
Le voyant LED LINK arrête de clignoter et s’éclaire en bleu en continu lorsqu’une connexion est établie entre la Soundbar et le module de réception sans fil.
Allumé en bleu
5.
Si le SWA-8500S n’est pas connecté, répétez la procédure de l’étape 2.
FRA - 9
04 CONNEXION À VOTRE TÉLÉVISEUR
Écoutez le son du téléviseur depuis la Soundbar via des connexions câblées ou sans fil.
• Lorsque la Soundbar est connectée à un téléviseur Samsung TV sélectionné, la Soundbar peut être contrôlée à l’aide de la télécommande du téléviseur.
– Cette fonction est prise en charge par les téléviseurs Samsung Smart TV sortis en 2017 et ultérieurement, et qui prennent en charge le Bluetooth lorsque vous connectez la Soundbar au téléviseur à l’aide d’un câble optique.
– Cette fonction vous permet également d’utiliser le menu du téléviseur pour ajuster le champ sonore et de nombreux réglages ainsi que le volume et la coupure du son.
Méthode 1. Connexion avec un câble
Lorsque les signaux de diffusion sont Dolby Digital et le réglage «Format audio de sortie numérique» est PCM sur votre téléviseur, il est recommandé de modifier le réglage sur Dolby Digital. Une fois le réglage modifié, vous pouvez profiter d’une meilleure qualité sonore. (Il se peut que le menu du téléviseur utilise des mots différents pour Dolby Digital et PCM en fonction du fabricant.)
Connexion d’un téléviseur à l’aide d’un câble HDMI
Contrôle de (ARC) au port
HDMI IN de votre téléviseur.
Câble HDMI
Partie inférieure de la Soundbar
HDMI IN
(ARC)
Contrôlez le port HDMI TO TV (ARC) de l'unité principale Soundbar.
Partie supérieure de la Soundbar
TV ARC
1.
Avec la Soundbar et le téléviseur allumés, connectez le câble HDMI tel qu’illustré.
2.
«
TV ARC
» apparaît sur la fenêtre d’affichage de l’unité principale Soundbar et vous pouvez entendre le son du téléviseur.
FRA - 10
• Si le son du téléviseur est inaudible, appuyez sur le bouton
(Source)
de la télécommande ou de la partie supérieure de la Soundbar pour passer en mode «
D.IN
». L’écran affiche successivement «
D.IN
» et «
TV ARC
», et vous pouvez entendre le son du téléviseur.
• Si «
TV ARC
» n’apparaît pas sur la fenêtre d’affichage de l’unité principale Soundbar, vérifiez que le câble HDMI est connecté au bon port.
• Utilisez les touches de volume sur la télécommande du téléviseur pour modifier le volume de la
Soundbar.
REMARQUES
• HDMI est une interface qui permet la transmission numérique de données vidéo et audio avec un seul connecteur.
• Si le téléviseur possède un port ARC, connectez le câble HDMI au port HDMI IN (ARC).
• Il est recommandé d’utiliser un câble HDMI sans fil si possible. Si vous utilisez un câble HDMI à fil, utilisez un câble dont le diamètre est inférieur à 14 mm.
• Cette fonction n’est pas disponible si le câble HDMI ne prend pas en charge l’ARC.
Connexion à l’aide d’un câble optique
Partie inférieure de la Soundbar
DIGITAL AUDIO IN (OPTICAL)
Câble optique
(non fourni)
OPTICAL OUT
Partie supérieure de la Soundbar
D.IN
1.
Raccordez la prise
DIGITAL AUDIO IN (OPTICAL)
de la Soundbar à la prise OPTICAL OUT du téléviseur à l’aide d’un câble optique (non fourni) numérique.
2.
Appuyez sur le bouton
(Source)
du panneau supérieur ou de la télécommande, puis sélectionnez le mode «
D.IN
».
FRA - 11
Utilisation de la fonction Q-Symphony
Pour Q-Symphony, la Soundbar se synchronise avec un téléviseur Samsung pour diffuser le son via deux périphériques pour un effet surround optimal. Quand la Soundbar est connectée, le menu
«
TV+Soundbar
» apparaît dans le menu
Sortie son
du téléviseur. Sélectionnez le menu correspondant.
Menu TV
Câble HDMI
OU
D.IN
Câble optique (non fourni)
• Exemple de menu TV :
TV Nom de série + [AV] Soundbar Nom de série (HDMI)
REMARQUES
• Il peut fonctionner selon le codec pris en charge par le téléviseur.
• Cette fonction n’est prise en charge que lorsque le câble HDMI ou le câble optique (non fourni) est connecté.
• Cette fonction est disponible sur les téléviseurs Samsung sortis en 2020 et sur certains modèles de
Soundbar.
FRA - 12
Méthode 2. Connexion sans fil
Connexion à un téléviseur via Bluetooth
Lorsqu’un téléviseur est connecté à l’aide de Bluetooth, vous pouvez écouter le son stéréo sans tracas de câblage.
• Seul un téléviseur à la fois peut être connecté.
PAIR
OU
D
MOD
E
Connexion initiale
1.
Appuyez sur la touche
PAIR
de la télécommande pour passer au mode «
BT PAIRING
».
(OU)
a.
Appuyez sur le bouton
(Source)
situé sur le panneau supérieur, puis sélectionnez
«
BT
».
«
BT
» passe automatiquement en «
BT PAIRING
» en quelques secondes ou en «
BT READY
» en cas de connexion enregistrée.
b.
Lorsque «
BT READY
» apparaît, maintenez le bouton
(Source)
enfoncé sur le panneau supérieur de la Soundbar pendant plus de 5 secondes pour afficher «
BT PAIRING
».
2.
Sélectionnez le mode Bluetooth sur le téléviseur. (Pour plus d’informations, reportez-vous au manuel du téléviseur.)
3.
Sélectionnez «
[AV] Samsung Soundbar Q6T-Series
» dans la liste sur l’écran du téléviseur.
Une Soundbar disponible est indiquée «
Need Pairing
» ou «
Paired
» dans la liste des appareils
Bluetooth sur le téléviseur. Pour connecter la Soundbar, sélectionnez le message et établissez la connexion.
• Lorsque le téléviseur est connecté, [
Nom du téléviseur
]→ «
BT
» apparaît sur l’affichage avant de la Soundbar.
4.
Vous pouvez maintenant entendre le son du téléviseur depuis la Soundbar.
Si la connexion de l’appareil échoue
• Si la liste de Soundbar connectées précédemment (par ex. «
[AV] Samsung Soundbar Q6T-Series
» apparaît dans la liste, supprimez-la.
• Ensuite, répétez les étapes 1 à 3.
REMARQUE
• Après avoir connecté la Soundbar au téléviseur pour la première fois, utilisez le mode «
BT READY
» pour la reconnexion.
FRA - 13
Déconnexion de la Soundbar à partir du téléviseur
Appuyez sur le bouton
(Source)
du panneau supérieur ou de la télécommande et activez l’un des modes, à l’exception du mode «
BT
».
• La déconnexion prend du temps parce que le téléviseur doit recevoir une réponse de la Soundbar.
(Le temps requis peut varier selon le modèle de téléviseur.)
• Pour annuler la connexion Bluetooth automatique entre la Soundbar et le téléviseur, appuyez sur la touche
Gauche
sur la télécommande pendant 5 secondes avec la Soundbar en mode «
BT READY
».
(Commutez Activé → Désactivé)
Quelle est la différence entre BT READY et BT PAIRNG ?
•
BT READY
: Dans ce mode, vous pouvez rechercher les téléviseurs connectés précédemment ou connecter un appareil mobile connecté précédemment à la Soundbar.
•
BT PAIRING
: Dans ce mode, vous pouvez connecter un nouvel appareil à la Soundbar. (Appuyez sur le bouton
PAIR
de la télécommande ou maintenez le bouton
(Source)
situé sur la partie supérieure de la Soundbar enfoncé pendant plus de 5 secondes lorsque la Soundbar est en mode
«
BT
».)
REMARQUES
• Si un code PIN est demandé lors de la connexion d’un appareil Bluetooth, saisissez <0000>.
• En mode de connexion Bluetooth, la connexion Bluetooth sera perdue si la distance entre la
Soundbar et l’appareil Bluetooth dépasse 10 m.
• La Soundbar s’éteint automatiquement après 20 minutes en état Prêt.
• Il se peut que la Soundbar ne puisse pas effectuer correctement la recherche Bluetooth ou la connexion dans les circonstances suivantes:
– En cas de champ électrique puissant autour de la Soundbar.
– Si deux appareils Bluetooth ou plus sont appariés simultanément avec la Soundbar.
– Si l’appareil Bluetooth est éteint, non installé, ou présente un dysfonctionnement.
• Les appareils qui génèrent des ondes électromagnétiques doivent être conservés à distance de l’unité principale Soundbar - par ex. des micro-ondes, des appareils LAN sans fil, etc.
FRA - 14
05 CONNEXION À UN APPAREIL EXTERNE
Raccordez un appareil externe via une connexion câblée ou une connexion Bluetooth pour écouter le son de l’appareil externe via la Soundbar.
Connexion à l’aide d’un câble HDMI
Partie inférieure de la Soundbar
HDMI OUT
HDMI
Appareil externe
Câble HDMI
HDMI IN
(ARC)
Câble HDMI
Partie supérieure de la Soundbar
HDMI
1.
Raccordez un câble HDMI de la prise
HDMI
au dos du produit à la prise HDMI OUT de votre appareil numérique.
2.
Raccordez un câble HDMI de la prise
HDMI TO TV (ARC)
au dos du produit à la prise HDMI IN de votre téléviseur.
3.
Appuyez sur le bouton
(Source)
du panneau supérieur ou de la télécommande, puis sélectionnez
«
HDMI
».
4.
Le mode «
HDMI
» s’affiche sur le panneau d’affichage de la Soundbar et vous pouvez entendre le son.
FRA - 15
Connexion à l’aide d’un câble optique
Partie inférieure de la Soundbar
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
Câble optique
(non fourni)
Partie supérieure de la Soundbar
OPTICAL OUT
Lecteur BD/DVD /
Boîtier décodeur /
Console de jeu
D.IN
1.
Raccordez
DIGITAL AUDIO IN (OPTICAL)
de l’unité principale à la prise OPTICAL OUT de l’appareil source à l’aide d’un câble optique (non fourni) numérique.
2.
Sélectionnez le mode «
D.IN
» en appuyant sur le bouton
(Source)
situé sur le panneau frontal ou sur la télécommande.
FRA - 16
06 CONNEXION D’UN PÉRIPHÉRIQUE DE
STOCKAGE USB
Vous pouvez lire des fichiers musicaux situés sur les périphériques de stockage USB via la Soundbar.
USB (5V 0.5A)
DC 24V
Port USB
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
USB
1.
Connectez l’appareil USB au port USB situé sur la partie inférieure du produit.
2.
Appuyez sur le bouton
(Source)
du panneau supérieur ou de la télécommande, puis sélectionnez «
USB
».
3.
«
USB
» apparaît sur l’écran d’affichage.
4.
Lisez des fichiers musicaux depuis le périphérique de stockage USB via la Soundbar.
• La Soundbar s’éteint automatiquement (Auto Power Down) si aucun périphérique USB n’a été connecté pendant plus de 20 minutes.
Liste de compatibilités
Extension
*.mp3
Codec
MPEG1 Layer2
MPEG1 Layer3
MPEG2 Layer3
MPEG2.5 Layer3
WMA7/8/9 (Audio uniquement)
Vorbis
Débit d'échantillonnage
32 ~ 48 kHz
32 ~ 48 kHz
16 ~ 24 kHz
8 ~ 12 kHz
32 ~ 48 kHz
32 ~ 48 kHz
Débit binaire
32 ~ 320 kbps
32 ~ 320 kbps
8 ~ 160 kbps
8 ~ 160 kbps
32 ~ 320 kbps
45 ~ 500 kbps
*.wma
*.ogg
*.aac
*.m4a
*.mp4
*.wav
*.flac
*.aiff
AAC-LC
(MPEG2/MPEG4 Audio uniquement)
32 ~ 48 kHz 32 ~ 320 kbps
LPCM
FLAC
AIFF
32 ~ 192 kHz
32 ~ 192 kHz
32 ~ 192 kHz
1024 ~ 9216 kbps
162 ~ 8100 kbps
1024 ~ 9216 kbps
• Si votre périphérique USB contient trop de dossiers et de fichiers, la Soundbar mettra peut-être du temps à accéder à vos fichiers et à les lancer.
FRA - 17
07 CONNEXION À UN APPAREIL MOBILE
Connexion via Bluetooth
Lorsqu’un appareil est connecté à l’aide de Bluetooth, vous pouvez écouter le son stéréo sans tracas de câblage.
• La connexion est limitée à un téléviseur ou deux appareils Bluetooth à la fois.
PAIR
OU
Appareil Bluetooth
D
MOD
E
Connexion initiale
1.
Appuyez sur la touche
PAIR
de la télécommande pour passer au mode «
BT PAIRING
».
(OU)
a.
Appuyez sur le bouton
(Source)
situé sur le panneau supérieur, puis sélectionnez
«
BT
».
«
BT
» passe automatiquement en «
BT PAIRING
» en quelques secondes ou en «
BT READY
» en cas de connexion enregistrée.
b.
Lorsque «
BT READY
» apparaît, maintenez le bouton
(Source)
enfoncé sur le panneau supérieur de la Soundbar pendant plus de 5 secondes pour afficher «
BT PAIRING
».
2.
Sélectionnez «
[AV] Samsung Soundbar Q6T-Series
» dans la liste.
• Lorsqu’une Soundbar est connectée à l’appareil Bluetooth, [
Nom de l’appareil Bluetooth
] →
«
BT
» apparaît sur l’affichage avant.
3.
Lisez des fichiers musicaux à partir de l’appareil, connecté via Bluetooth, via la Soundbar.
Si la connexion de l’appareil échoue
• Si la liste de Soundbar connectées précédemment (par ex. «
[AV] Samsung Soundbar Q6T-Series
» apparaît dans la liste, supprimez-la.
• Ensuite, répétez les étapes 1 et 2.
REMARQUE
• Après avoir connecté la Soundbar au appareil mobile pour la première fois, utilisez le mode «
BT
READY
» pour la reconnexion.
FRA - 18
Quelle est la différence entre BT READY et BT PAIRING ?
•
BT READY
: Dans ce mode, vous pouvez rechercher les téléviseurs connectés précédemment ou connecter un appareil mobile connecté précédemment à la Soundbar.
•
BT PAIRING
: Dans ce mode, vous pouvez connecter un nouvel appareil à la Soundbar. (Appuyez sur le bouton
PAIR
de la télécommande ou maintenez le bouton
(Source)
situé sur la partie supérieure de la Soundbar enfoncé pendant plus de 5 secondes lorsque la Soundbar est en mode
«
BT
».)
REMARQUES
• Si un code PIN est demandé lors de la connexion d’un appareil Bluetooth, saisissez <0000>.
• En mode de connexion Bluetooth, la connexion Bluetooth sera perdue si la distance entre la
Soundbar et l’appareil Bluetooth dépasse 10 m.
• La Soundbar s’éteint automatiquement après 20 minutes en état Prêt.
• Il se peut que la Soundbar ne puisse pas effectuer correctement la recherche Bluetooth ou la connexion dans les circonstances suivantes:
– En cas de champ électrique puissant autour de la Soundbar.
– En cas d’appariement simultané de plusieurs appareils Bluetooth avec la Soundbar.
– Si l’appareil Bluetooth est éteint, non installé, ou présente un dysfonctionnement.
• Les appareils qui génèrent des ondes électromagnétiques doivent être conservés à distance de l’unité principale Soundbar - par ex. des micro-ondes, des appareils LAN sans fil, etc.
• Le Soundbar prend en charge les données SBC (44,1 kHz, 48 kHz).
• Effectuez uniquement la connexion à un périphérique Bluetooth qui prend en charge la fonction A2DP (AV).
• Vous ne pouvez pas connecter le Soundbar à un périphérique Bluetooth qui prend en charge uniquement la fonction HF (Hands Free).
• Lorsque vous avez apparié la barre audio à un périphérique Bluetooth, sélectionner «
[AV] Samsung
Soundbar Q6T-Series
» parmi la liste des périphériques connectés à ce périphérique placera automatiquement la barre audio en mode «
BT
».
– Disponible uniquement si le Soundbar est listé dans les périphériques appariés du périphérique
Bluetooth. (Le périphérique Bluetooth et le Soundbar doivent être appariés au préalable au moins une fois)
• Le Soundbar apparaîtra dans la liste des périphériques recherchés du périphérique Bluetooth uniquement lorsque le Soundbar affiche «
BT READY
».
Bluetooth Power Activé (SOUND MODE)
Lorsque la fonction Bluetooth Power Activé est activée et que le Soundbar est désactivé, si un périphérique Bluetooth précédemment associé essaye de se connecter au Soundbar, le Soundbar s’active automatiquement.
1.
Appuyez sur la touche
SOUND MODE
et maintenez-la enfoncée pendant plus de 5 secondes sur la télécommande pendant que la Soundbar est sous tension.
2.
«
ON-BLUETOOTH POWER
» s’affiche sur l’écran de la Soundbar.
FRA - 19
Déconnexion de l’appareil Bluetooth d’une Soundbar
Vous pouvez déconnecter le périphérique Bluetooth du système Soundbar. Pour les instructions, reportez-vous au manuel d’utilisation de ce périphérique.
• Le système Soundbar sera déconnecté.
• Lorsque la Soundbar est déconnectée de l’appareil Bluetooth, la Soundbar affichera
«
BT DISCONNECTED
» sur l’affichage avant.
Déconnexion de la Soundbar à partir de l’appareil Bluetooth
Appuyez sur le bouton
(Source)
situé sur le panneau supérieur ou la télécommande , puis passez dans n’importe lequel des modes, à l’exception du mode «
BT
».
• La déconnexion prend du temps parce que l’appareil Bluetooth doit recevoir une réponse de la
Soundbar. (La durée de déconnexion peut varier selon l’appareil Bluetooth)
• Lorsque la Soundbar est déconnectée de l’appareil Bluetooth, la Soundbar affichera
«
BT DISCONNECTED
» sur l’affichage avant.
REMARQUES
• En mode Bluetooth, la connexion sera perdue si la distance entre le système Soundbar et le périphérique Bluetooth dépasse 10 m.
• Le système Soundbar s’éteint après 20 minutes en état Prêt.
À propos du Bluetooth
Le système Bluetooth est une technologie qui permet de connecter facilement entre eux des périphériques compatibles Bluetooth à l’aide d’une liaison sans fil courte distance.
• Ce périphérique Bluetooth peut générer du bruit ou créer des dysfonctionnements en fonction des conditions d’utilisation lorsque:
– Une partie du corps de l’appareil est en contact avec le système de réception/transmission du périphérique Bluetooth ou du système Soundbar.
– Il est soumis à des variations électriques provenant d’obstructions provoquées par un mur, un coin ou des cloisonnements de bureaux.
– Il est exposé à des interférences électriques provenant d’appareils utilisant la même bande de fréquences (exemple : équipements médicaux, fours à micro-ondes et réseaux LAN sans fil).
• Associer le système Soundbar et le périphérique Bluetooth tout en maintenant une faible distance.
• Plus la distance est grande entre l’Soundbar et le périphérique Bluetooth, plus la qualité de la transmission se dégrade. Si la distance excède la plage opérationnelle Bluetooth, la connexion est perdue.
• Dans les zones où la réception est faible, la connexion Bluetooth peut ne pas fonctionner correctement.
• La connexion Bluetooth ne fonctionne que lorsqu’elle est proche de l’appareil. La connexion s’interrompt automatiquement lorsque cette plage est dépassée. Même si la distance est respectée, il est possible que la qualité sonore soit détériorée par des obstacles (ex. : murs, portes).
• Cet appareil sans fil peut causer des interférences électriques lors de son fonctionnement.
FRA - 20
Connexion Multi-Bluetooth
Il est possible de connecter la Soundbar à 2 appareils Bluetooth à la fois.
Appareil Bluetooth A Appareil Bluetooth B
1.
Connectez la Soundbar jusqu’à deux appareils Bluetooth. (Voir page 18)
2.
Lisez de la musique à partir de l’un des appareils Bluetooth connectés lorsque deux appareils sont connectés.
3.
Pour lire de la musique à partir de l’appareil Bluetooth «B» alors que la lecture est en cours à partir de l’appareil «A», mettez la lecture en pause ou arrêtez-la sur l’appareil «A», puis lancez la lecture sur l’appareil «B».
• L’appareil ne commutera pas sur de la musique est en cours de lecture à partir de l’appareil «B» tant que vous n’avez pas mis en pause ou arrêté l’appareil «A».
4.
Dans les versions antérieures à AVRCP V1.4, la durée de commutation de l’appareil sur lequel de la musique est en cours de lecture peut être supérieure.
REMARQUES
• Si vous essayez de connecter un troisième appareil Bluetooth, l’appareil A ou B sera déconnecté.
(L’appareil qui n’est pas en cours de lecture sera déconnecté.)
• Un seul téléviseur Samsung, ou 2 appareils Bluetooth peuvent être connectés en même temps.
• La Soundbar sera déconnecté des appareils Bluetooth si elle reçoit une demande de connexion d’un téléviseur Samsung TV.
FRA - 21
08 UTILISATION DE LA TÉLÉCOMMANDE
Comment utiliser la télécommande
SOUND
MODE
PAIR
VOL WOOFER
SOUNDBAR
Allume et éteint la Soundbar.
Alimentation
Appuyez pour sélectionner une source connectée à la Soundbar.
Source
Appuyez sur la touche (
Coupure de son
) pour
VOL
Coupure de son
touche pour activer le son.
SOUND
MODE
SOUND MODE
SOUND
Vous pouvez sélectionner l'effet sonore souhaité en choisissant parmi
STANDARD
,
SURROUND
SOUND
,
GAME PRO
,
ADAPTIVE SOUND
ou
DTS
VIRTUAL:X
.
–
STANDARD
PAIR
–
SURROUND SOUND
VOL
SOUND
MODE
VOL norme.
–
GAME PRO
Fournit un son stéréoscopique vous permettant une immersion dans l’action pendant le jeu.
WOOFER
VOL
–
ADAPTIVE SOUND
Analyse le contenu en temps réel et fournit automatiquement le champ sonore optimal sur la base des caractéristiques du contenu.
–
DTS VIRTUAL:X
Son 3D immersif à partir de n’importe quel contenu.
FRA - 22
PAIR
SOUND
MODE
Bluetooth
PAIR
•
DRC (Dynamic Range Control)
Vous permet d’effectuer une commande de plage dynamique des pistes Dolby Digital.
Appuyez et maintenez enfoncée la touche
SOUND MODE
pendant que la Soundbar est hors tension pour activer ou désactiver le DRC (Dynamic Range Control). Avec la fonction DRC activée, le bruit est réduit. (Le son peut être déformé.)
•
Bluetooth Power
Cette fonction allume automatiquement la Soundbar à la réception d’une demande de connexion d’un téléviseur ou d’un appareil Bluetooth connecté précédemment. Le réglage est activé par défaut.
– Appuyez et maintenez enfoncée la touche
SOUND MODE
pendant plus de
5 secondes pour désactiver la fonction Bluetooth Power.
Appuyez sur la touche
PAIR
. «
BT PAIRING
» s'affiche sur l'écran de la Soundbar.
Vous pouvez connecter la Soundbar à un nouvel appareil Bluetooth dans ce mode en sélectionnant la Soundbar dans la liste de recherche d'appareils Bluetooth.
Appuyez sur la touche
p
pour mettre le fichier musical temporairement en pause.
Si vous appuyez à nouveau sur la touche, le fichier musical est lu.
Lecture / Pause
VOL WOOFER
PAIR
Appuyez sur les zones indiquées pour sélectionner Haut/Bas/
Gauche/Droite.
Haut/Bas/
PAIR
Gauche/
VOL
VOL WOOFER
WOOFER
Appuyez sur Haut/Bas/Gauche/Droite sur la touche pour sélectionner ou paramétrer les fonctions.
•
Répétition
Pour utiliser la fonction de répétition en mode «
USB
», appuyez sur la touche
Haut
.
•
Saut de fichier musical
Appuyez sur la touche
Droite
pour sélectionner le fichier musical suivant.
Appuyez sur la touche
Gauche
pour sélectionner le fichier musical précédent.
•
ID SET
Appuyez et maintenez enfoncée la touche
Haut
pendant 5 secondes pour terminer
ID SET
(lors de la connexion à un accessoire).
FRA - 23
SOUND
MODE
Commande sonore
PAIR
•
Fonction de restriction du volume
Pour protéger votre audition, la fonction Restriction du volume limite le volume à 20 si vous allumez la Soundbar lorsque le volume est réglé plus haut que 20.
– La valeur par défaut pour la fonction Restriction du volume est désactivée.
Vous devez la régler sur activée pour l’activer.
– Lorsqu’elle est activée, la fonction Restriction du volume reste activée même lorsque l’alimentation est coupée.
– Pour activer ou désactiver Restriction du volume, appuyez et maintenez enfoncée la touche
Bas
sur la télécommande pendant 5 secondes. Lorsque Volume
Restriction (Restriction du volume) est désactivée, «
V FREE
» apparaît sur l’affichage avant. Lorsque cette fonction est activée, «
V LOCK
» apparaît.
Vous pouvez sélectionner parmi
TREBLE
,
BASS
, ou
AUDIO SYNC
.
• Pour contrôler le volume des aigus et des graves, appuyez sur la touche
Commande sonore
pour sélectionner
TREBLE
ou
BASS
puis ajustez le volume, de -6 à +6, à l’aide des touches
Haut/Bas
.
• Appuyez et maintenez enfoncée la touche
(Commande sonore)
pendant environ
5 secondes pour ajuster le son pour chaque bande de fréquence. 150 Hz, 300 Hz,
600 Hz, 1,2 kHz, 2,5 kHz, 5 kHz et 10 kHz peuvent être sélectionnés à l’aide des touches
Gauche/Droite
et chaque réglage peut être défini entre -6 et +6 à l’aide des touches
Haut/Bas
.
• Si l’image sur le téléviseur et le son de la Soundbar ne sont pas synchronisés, appuyez sur la touche
Commande sonore
pour sélectionner
AUDIO SYNC
puis réglez le décalage audio de 0 à 300 millisecondes à l’aide des touches
Haut/Bas
. (Non disponible en mode «
USB
» ou «
BT
»)
• Si les enceintes Surround sont connectées, il est possible d’activer/de désactiver la fonction enceinte arrière en utilisant les boutons
Haut/Bas
pour ajuster le volume à l’intérieur d’une plage allant de -6 à +6.
•
AUDIO SYNC
n’est pris en charge que dans certaines fonctions.
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
VOL
SOU
ND
MO
DE
VOL
WOOFE
R
SOUND
MODE
PAIR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Déplacez la touche
WOOFER
vers l'avant ou l'arrière pour ajuster le volume du subwoofer sur -12 ou entre -6 et +6. Pour régler le niveau de volume du caisson de basse sur 0, appuyez sur la touche.
VOL WOOFER
WOOFER
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Déplacez sur la touche
VOL
vers l'avant ou l'arrière pour ajuster le volume.
•
Coupure de son
Appuyez sur la touche
VOL
pour couper le son. Appuyez de nouveau sur cette touche pour activer le son.
FRA - 24
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Réglage du volume de la
Soundbar avec une télécommande de téléviseur
Si vous avez un téléviseur Samsung, vous pouvez régler le volume de la Soundbar à l’aide de la télécommande IR fournie avec votre téléviseur Samsung.
Utilisez d’abord le menu du téléviseur pour régler le son de votre téléviseur Samsung sur les enceintes externes, puis utilisez votre télécommande Samsung pour contrôler le volume de la Soundbar. Pour plus d’informations, reportezvous au manuel d’utilisateur du téléviseur. Le mode par défaut de cette fonction est contrôlé par une télécommande de téléviseur Samsung. Si votre téléviseur n’est pas un téléviseur Samsung, suivez les instructions ci-dessous pour changer les réglages de cette fonction.
1.
Éteignez la Soundbar.
BYE
2.
Si vous ne voulez pas utiliser cette fonction, poussez la touche
WOOFER
vers le haut et maintenez-la enfoncée pendant 5 secondes jusqu’à ce que «
OFF-TV REMOTE
» apparaisse à l’écran.
4.
Si vous voulez restaurer la Soundbar en mode par défaut (contrôlé par une télécommande d’un téléviseur Samsung), poussez la touche
WOOFER
vers le haut et maintenez-la enfoncée pendant 5 secondes jusqu’à ce que «
SAMSUNG-TV REMOTE
» apparaisse à l’écran.
5 Sec
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
(Mode par défaut)
SAMSUNG-TV REMOTE
– Chaque fois que vous poussez la touche
WOOFER
vers le haut et la maintenez enfoncée pendant 5 secondes, le mode commute dans l’ordre suivant :
«
SAMSUNG-TV REMOTE
» (Mode par défaut) → «
OFF-TV REMOTE
» → «
ALL-TV
REMOTE
».
– La disponibilité de cette fonction dépend de la télécommande.
– Fabricants prenant en charge cette fonction: VIZIO, LG, Sony, Sharp, PHILIPS,
PANASONIC, TOSHIBA, Hisense, RCA
SOU
ND
MO
DE
5 Sec OFF-TV REMOTE
VOL
WOOFE
R
SOUNDB
AR
3.
Si vous voulez contrôler la Soundbar avec la télécommande de votre téléviseur, poussez la touche
WOOFER
vers le haut et maintenez-la enfoncée pendant 5 secondes jusqu’à ce que
«
ALL-TV REMOTE
» apparaisse à l’écran.
Utilisez ensuite le menu de votre téléviseur pour sélectionner les enceintes externes.
5 Sec
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
ALL-TV REMOTE
FRA - 25
Utilisation des touches dissimulées (Touches avec plus d’une fonction)
Touche de télécommande
Touche dissimulée
WOOFER (Haut)
p
(Lecture / Pause)
Gauche
Fonction
Télécommande de votre téléviseur
Activer/Désactiver (Veille)
Initialiser (Veille)
Activation/désactivation de la connexion automatique au téléviseur (BT prêt)
Haut
Bas
(Commande sonore)
ID SET (Veille)
Restriction du volume Activer/Désactiver
(Veille)
EQ bande 7
DRC ON/OFF ( Veille)
SOUND MODE
Bluetooth Power
Page de référence
page
page
page
Spécifications de sortie pour les différents modes d’effets sonores
Sortie
Surround
SOUND
MODE
Bluetooth
POWER
SURROUND
SOUND
SOUND MODE
Effet
STANDARD
GAME PRO
ADAPTIVE
SOUND
Entrée
2.0 canaux
5.1 canaux
2.0 canaux
5.1 canaux
2.0 canaux
5.1 canaux
2.0 canaux
5.1 canaux
Sans kit d’enceintes arrière sans fil
2.1 canaux
3.1 canaux
4.1 canaux
5.1 canaux
4.1 canaux
5.1 canaux
4.1 canaux
5.1 canaux
Avec kit d’enceintes arrière sans fil
4.1 canaux
5.1 canaux
6.1 canaux
7.1 canaux
6.1 canaux
7.1 canaux
6.1 canaux
7.1 canaux
2.0 canaux 3.1 canaux 5.1 canaux
VOL WOOFER
DTS VIRTUAL:X
5.1 canaux 3.1 canaux 5.1 canaux
• Le kit d’enceintes arrière sans fil Samsung peut être acheté séparément. Pour acheter un kit, contactez le vendeur chez qui vous avez acheté la Soundbar.
FRA - 26
09 INSTALLATION
DU SUPPORT
MURAL
Composants de fixation au mur
Guide de fixation murale
Précautions d’installation
• Installez sur un mur vertical uniquement.
• N’installez pas dans un endroit à température
élevée ou humide.
• Vérifiez si le mur est suffisamment robuste pour supporter le poids du produit.
Sinon, renforcez le mur ou choisissez un autre point d’installation.
• Achetez et utilisez les vis de fixation ou les ancrages appropriés pour le type de mur dont vous disposez (plaque de plâtre, plaque métallique, bois, etc.). Si possible, fixez les vis portantes dans les poteaux.
• Achetez les vis de support mural selon le type et l’épaisseur du mur sur lequel vous souhaitez monter la Soundbar.
– Diamètre: M5
– Longueur: 35 mm ou plus recommandés.
• Connectez les câbles depuis l’unité aux appareils externes avant d’installer la
Soundbar sur le mur.
• Assurez-vous que l’unité est éteinte et débranchée avant de l’installer. Sinon, cela pourrait provoquer un choc électrique.
x 2
Vis de fixation
x 2
Vis
x 2
Support de fixation murale
1.
Placez le
Guide de fixation murale
contre le mur.
• Le
Guide de fixation murale
doit être de niveau.
• Si votre téléviseur est monté sur le mur, installez la Soundbar à au moins 5 cm sous le téléviseur.
5 cm minimum
FRA - 27
2.
Alignez la
Ligne centrale du Guide de fixation murale
avec le centre de votre téléviseur (si vous fixez la Soundbar sous votre téléviseur), puis fixez le
Guide de fixation murale
au mur avec du ruban adhésif.
• Si vous ne fixez pas la Soundbar sous un téléviseur, placez la
Ligne centrale
au centre de la zone d’installation.
5.
Enfoncez une vis (non fournie) dans chaque
Vis de fixation
, puis vissez fermement chaque vis dans un trou pour vis portante.
6.
Installez les
Support de fixation murale
sur la partie inférieure de la Soundbar, en veillant à les positionner correctement, en utilisant 2
Vis
.
Ligne centrale
3.
Appuyez avec la pointe d’un stylo ou d’un crayon bien taillé au centre des images
A-TYPE
à chaque extrémité du guide pour marquer les trous des vis portantes, puis retirez le
Guide de fixation murale
.
4.
À l’aide d’une mèche appropriée, faites un trou dans le mur au niveau de chaque marque.
• Si les marques ne correspondent pas aux positions des poteaux muraux, veillez à insérer les ancrages ou les chevilles Molly appropriées dans les trous avant d’insérer les vis portantes. Si vous utilisez des ancrages ou des chevilles Molly, pensez à percer des trous suffisamment larges pour les accueillir.
• Lors de l’assemblage, veillez à ce que l’accroche des
Support de fixation murale
se trouve sur l’arrière de la
Soundbar.
Arrière de la Soundbar
Extrémité droite de la Soundbar
FRA - 28
7.
Installez la Soundbar, sur laquelle sont fixés les
Supports de fixation murale
, en accrochant les
Supports de fixation murale
sur les
Vis de fixation
sur le mur.
10 INSTALLATION
DE LA
SOUNDBAR SUR
UN SOCLE DE
TÉLÉVISEUR
8.
Faites glisser la Soundbar vers le bas, comme indiqué ci-dessous, afin que les
Support de fixation murale
reposent de manière sûre sur les
Vis de fixation
.
• Insérez les
Vis de fixation
dans la partie large (inférieure) des
Support de fixation murale
, puis faites glisser les
Support de fixation murale
vers le bas afin que les
Support de fixation murale
reposent de manière sûre sur les
Vis de fixation
.
Placez la Soundbar sur un socle de téléviseur.
3 cm o u plus
Comme indiqué sur l’illustration, alignez le centre de la Soundbar avec le centre du téléviseur, en insérant avec précaution la Soundbar dans le socle du téléviseur.
Pour obtenir une qualité sonore optimale, positionnez la Soundbar à une distance d’au moins 3 cm de la partie avant du téléviseur.
REMARQUE
• Veillez à ce que la Soundbar soit placée sur une surface plane et stable.
FRA - 29
11 MISE À JOUR DU
LOGICIEL
Samsung peut proposer des mises à jour pour le microprogramme du système de la Soundbar prochainement.
Port USB
USB (5V 0.5A)
DC 24V
HDMI
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
Si une mise à jour est proposée, vous pouvez mettre à jour le microprogramme en connectant le périphérique USB contenant la mise à jour du microprogramme enregistré au port USB de votre
Soundbar. Pour plus d’informations sur comment télécharger des fichiers de mise à jour, rendezvous sur le site Samsung
(www.samsung.com
Support).
Ensuite, sélectionnez le type de produit ou entrez le modèle de votre Soundbar, sélectionnez l’option Logiciels et applications, puis
Téléchargements. Notez que les noms d’option peuvent varier.
Procédure de mise à jour
Important :
La fonction de mise à jour efface tous les paramètres utilisateur. Nous vous recommandons d’écrire vos paramètres pour pouvoir les rétablir après la mise à jour. Notez que la mise à jour du micrologiciel réinitialise
également la connexion du subwoofer.
1.
Connectez une clé USB au port USB de votre ordinateur.
Important:
Assurez-vous qu’il n’y a pas de fichiers musicaux sur la clé USB. Cela peut entraîner l’échec de la mise à jour du micrologiciel.
2.
Rendez-vous sur le site Web Samsung sur
(samsung.com)
sélectionnez Entrer le numéro de modèle et entrez le modèle de votre Soundbar. Sélectionnez les manuels et les téléchargements, et téléchargez le dernier fichier du logiciel.
3.
Sauvegardez le logiciel téléchargé sur une clé USB et sélectionnez «Extraire ici» pour dézipper le fichier.
4.
Éteignez la Soundbar et connectez la clé USB contenant la mise à jour logicielle au port
USB.
5.
Allumez la Soundbar. Dans les 3 minutes qui suivent, «
UPDATE
» s’affiche et la mise à jour commence.
6.
Lorsque la mise à jour est terminée, la
Soundbar s’éteint. Appuyez sur la touche
p
de la télécommande pendant 5 secondes.
«
INIT
» s’affiche à l’écran puis la Soundbar s’éteint. La mise à jour est terminée.
• Ce produit est équipé de la fonction DUAL
BOOT. Si la mise à jour du micrologiciel
échoue, vous pouvez exécuter à nouveau la mise à jour.
7.
Restaurez vos paramètres sur la Soundbar.
FRA - 30
Si UPDATE ne s’affiche pas
1.
Éteignez la Soundbar, déconnectez et ensuite reconnectez le périphérique de stockage qui contient le fichier de mise à jour au port USB de la Soundbar.
2.
Débranchez le cordon d’alimentation de la
Soundbar, rebranchez-le, puis allumez la
Soundbar.
REMARQUES
• La mise à jour du micrologiciel peut ne pas se faire correctement si les fichiers audio reconnus par la Soundbar sont stockés dans le périphérique de stockage.
• N’éteignez pas l’appareil et ne retirez pas le périphérique USB lorsque les mises à jour sont en train d’être appliquées. L’unité principale s’éteindra automatiquement après avoir terminé la mise à jour du micrologiciel.
• Une fois la mise à jour terminée, la configuration d’utilisateur est initialisée dans la Soundbar. Nous vous recommandons d’écrire vos paramètres pour pouvoir les rétablir après la mise à jour. Notez que la mise
à jour du micrologiciel réinitialise également la connexion du subwoofer.
Si la connexion au subwoofer n’est pas rétablie automatiquement après la mise à
jour, reportez-vous à la page 6.
Si la mise à jour du logiciel échoue, contrôlez si la clé USB est défectueuse.
• Les utilisateurs de Mac OS doivent utiliser
MS-DOS (FAT) comme format USB.
• L’exécution de la mise à jour via USB peut ne pas être possible en fonction du fabricant du périphérique de stockage.
FRA - 31
12 DÉPANNAGE
Avant de contacter l’assistance, veuillez lire ce qui suit.
L’unité ne s’allume pas.
Le cordon d’alimentation est-il bien branché dans la prise murale et dans l’adaptateur d’alimentation?
;
Débranchez et reconnectez le cordon d’alimentation à la prise murale et à l’adaptateur d’alimentation pour vous assurer que la connexion est bien établie.
L’adaptateur d’alimentation est-il fermement connecté à l’unité principale?
;
Déconnectez l’adaptateur d’alimentation de la Soundbar et reconnectez-le pour vous assurer que la connexion est solide et sûre.
Une fonction ne répond pas lorsque la touche est enfoncée.
De l’électricité statique est-elle présente dans l’air?
;
Débranchez la fiche secteur et rebranchezla.
Des distorsions sonores se font entendre en mode BT.
;
Consultez les sections sur la connexion
Aucun son n’est produit.
La fonction de coupure du son est-elle activée ?
;
Appuyez sur le touche
(Coupure de son)
pour annuler la fonction de sourdine.
Le volume est-il réglé à son minimum ?
;
Réglez le volume.
La télécommande ne fonctionne pas.
Les piles sont-elle usées ?
;
Remplacez avec des piles neuves.
Est-ce que la distance entre la télécommande et l’unité principale Soundbar est trop grande ?
;
Rapprochez la télécommande de l’unité principale Soundbar.
La LED rouge sur le caisson de basse clignote et le caisson de basse ne produit aucun son.
Ce problème peut se produire si le caisson de basse n’est pas connecté à l’unité principale
Soundbar.
;
Essayez de reconnecter votre caisson de
Le caisson de basse bourdonne et vibre considérablement.
Essayez de régler les vibrations de votre caisson de basse.
;
Déplacez la touche
WOOFER
de votre télécommande vers l’avant ou l’arrière pour ajuster le volume du subwoofer.
(sur -12 ou entre -6 et +6)
FRA - 32
13 LICENCE 14 AVIS DE LICENCE
LIBRE
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
Pour toute requête et demande concernant les sources ouvertes, contactez Samsung via e-mail à l’adresse ([email protected]).
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol together, Digital Surround, and the Digital Surround logo are registered trademarks or trademarks of
DTS, Inc. in the United States and/or other countries.
© DTS, Inc. All Rights Reserved.
15 REMARQUE
IMPORTANTE À
PROPOS DU
SERVICE
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol together, Virtual:X, and the DTS Virtual:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc.
All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
• Les figures et les illustrations du présent
Manuel d’utilisation sont fournies à titre de référence uniquement et peuvent différer de l’apparence du produit réel.
• Des frais supplémentaires pourront vous être facturés dans les cas suivants :
(a) Vous demandez l’intervention d’un ingénieur, mais il s’avère que l’appareil ne présente aucune anomalie (par ex. vous n’avez pas lu ce Manuel d’utilisation).
(b) Vous portez l’unité à un centre de réparation, mais il s’avère que celle-ci ne présente aucune défaillance (par ex. vous n’avez pas lu ce Manuel d’utilisation).
• Le montant de ces frais administratifs vous sera notifié avant que tout travail ou toute visite à votre domicile ne soit effectuée).
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Samsung Electronics Co.,
Ltd. is under license. Other trademarks and trade names are those of their respective owners.
FRA - 33
16 SPÉCIFICATIONS ET GUIDE
Spécifications
Nom du modèle
USB
Poids
Dimensions (L x H x P)
Plage de températures en fonctionnement
Plage d’humidité en fonctionnement
AMPLIFICATEUR
Puissance de sortie nominale
Formats de lecture pris en charge
PUISSANCE DE SORTIE DE L’APPAREIL SANS FIL
Puissance de transmission BT max.
Puissance de transmission SRD max.
HW-Q60T
5V/0,5A
3,4 kg
980,0 x 58,0 x 105,0 mm
+5°C à +35°C
10 % ~ 75 %
30W x 6 + 10W x 2
LPCM 2ch, Dolby Audio™
(prise en charge de Dolby® Digital), DTS, DTS Virtual:X
6 mW à 2,402 GHz - 2,480 GHz
25 mW à 5,725 GHz – 5,825 GHz
Nom du caisson de basse
Poids
Dimensions (L x H x P)
AMPLIFICATEUR
Puissance de sortie nominale
PUISSANCE DE SORTIE DE L’APPAREIL SANS FIL
Puissance de transmission SRD max.
PS-WR65BB
6,2 kg
205,0 x 353,0 x 303,2 mm
160W
25 mW à 5,725 GHz – 5,825 GHz
Consommation électrique totale en veille (W)
Bluetooth
Méthode de désactivation du port
2,0W
Appuyez et maintenez enfoncée la touche
SOUND MODE
pendant plus de 5 secondes pour désactiver la fonction Bluetooth Power.
REMARQUES
• Samsung Electronics Co., Ltd se réserve le droit de modifier les caractéristiques sans préavis.
• Le poids et les dimensions sont approximatifs.
FRA - 34
• Samsung déclare par la présente que cet équipement est conforme à la directive 2014/53/UE.
Le texte complet de la déclaration de conformité de l’UE est disponible à l’adresse Internet suivante : http://www.samsung.com, puis allez dans
Assistance > Sélectionner un produit et saisissez le nom de modèle.
Cet équipement peut fonctionner dans tous les pays de l’Union européenne.
[Elimination des batteries de ce produit]
(Applicable aux pays disposant de systèmes de collecte séparés)
Le symbole sur la batterie, le manuel ou l’emballage indique que les batteries de ce produit ne doivent pas
être éliminées en fin de vie avec les autres déchets ménagers. L’indication éventuelle des symboles chimiques Hg, Cd ou Pb signifie que la batterie contient des quantités de mercure, de cadmium ou de plomb supérieures aux niveaux de référence stipulés dans la directive CE 2006/66.
Si les batteries ne sont pas correctement éliminées, ces substances peuvent porter préjudice à la santé humaine ou à l’environnement.
Afin de protéger les ressources naturelles et d’encourager la réutilisation du matériel, veillez à séparer les batteries des autres types de déchets et à les recycler via votre système local de collecte gratuite des batteries.
Les bons gestes de mise au rebut de ce produit (Déchets d’équipements électriques &
électroniques)
(Applicable aux pays disposant de systèmes de collecte séparés)
Ce symbole sur le produit, ses accessoires ou sa documentation indique que ni le produit, ni ses accessoires
électroniques usagés (chargeur, casque audio, câble USB, etc.) ne peuvent être jetés avec les autres déchets ménagers. La mise au rebut incontrôlée des déchets présentant des risques environnementaux et de santé publique, veuillez séparer vos produits et accessoires usagés des autres déchets. Vous favoriserez ainsi le recyclage de la matière qui les compose dans le cadre d’un développement durable.
Les particuliers sont invités à contacter le magasin leur ayant vendu le produit ou à se renseigner auprès des autorités locales pour connaître les procédures et les points de collecte de ces produits en vue de leur recyclage. Les entreprises et particuliers sont invités à contacter leurs fournisseurs et à consulter les conditions de leur contrat de vente. Ce produit et ses accessoires ne peuvent être jetés avec les autres déchets.
Pour obtenir des informations sur les engagements environnementaux de Samsung et sur les obligations réglementaires spécifiques à l’appareil, par ex. la réglementation REACH WEEE, rendez-vous sur : http://www.samsung.com/uk/aboutsamsung/samsungelectronics/corporatecitizenship/data_corner.html
RÈGLEMENT (UE) 2019/1782 DE LA COMMISSION
Exigences d’écoconception applicables aux sources d’alimentation externe : www.samsung.com/global/ecodesign_component
FRA - 35
INFORMAZIONI SULLA SICUREZZA
NORME PER LA SICUREZZA
PER RIDURRE I RISCHI DI FOLGORAZIONE, NON
RIMUOVERE IL COPERCHIO (O IL RETRO),
ALL’INTERNO NON VI SONO PARTI RIPARABILI
DALL’UTENTE. PER L’ASSISTENZA TECNICA FARE
RIFERIMENTO A PERSONALE QUALIFICATO.
Fare riferimento alla seguente tabella per una descrizione dei simboli che è possibile trovare sul proprio prodotto Samsung.
ATTENZIONE
RISCHIO DIFOLGORAZIONE.
NON APRIRE.
Questo simbolo indica che all'interno sono presenti tensioni pericolose.
E' pericoloso toccare in qualsiasi modo le parti interne di questo prodotto.
Questo simbolo indica la disponibilità di informazioni importanti nella letteratura del prodotto relative al funzionamento e alla manutenzione del dispositivo.
Prodotto di Classe II: Questo simbolo indica che il prodotto non necessita di una connessione di sicurezza alla terra.
Se questo simbolo non è presente su un prodotto con un cavo di alimentazione, il prodotto DEVE disporre di una connessione sicura a una presa di corrente dotata di messa a terra.
Tensione CA: Questo simbolo indica che la tensione contrassegnata con questo simbolo è di tipo CA.
Tensione CC : Questo simbolo indica che la tensione contrassegnata con questo simbolo è di tipo CC.
Attenzione, consultare le Istruzioni per l’uso: Questo simbolo indica all’utente la necessità di consultare il manuale dell’utente per ottenere ulteriori informazioni sulla sicurezza.
AVVERTENZA
• Per ridurre i rischi d’incendio e di scosse elettriche non esporre l’ apparecchio a pioggia o umidità.
ATTENZIONE
• PER EVITARE SCOSSE ELETTRICHE, INSERIRE
CORRETTAMENTE E COMPLETAMENTE LA
SPINA.
• Questo dispositivo deve essere sempre collegato ad una presa elettrica dotata di messa a terra di protezione.
• Per scollegare il dispositivo dalla rete elettrica, lo spinotto deve essere estratto dalla presa, pertanto esso deve essere facilmente raggiungibile.
• Non schizzare o sgocciolare liquidi sull’apparecchio. Non sistemare oggetti pieni di liquidi, come dei vasi, sull’apparecchio.
• Per spegnere completamente l’apparecchio, estrarre la spina di alimentazione dalla presa di rete.
Di conseguenza, la spina di alimentazione deve essere facilmente e prontamente accessibile in qualsiasi momento.
ITA - ii
PRECAUZIONI
1.
Assicurarsi che l’alimentazione CA della propria abitazione sia conforme ai requisiti di potenza riportati sull’adesivo di identificazione situato sulla parte inferiore del prodotto. Installare il prodotto orizzontalmente, su un supporto adeguato
(mobile), verificando che vi sia spazio sufficiente per una corretta ventilazione 7 -
10 cm. Assicurarsi che le aperture di ventilazione non siano coperte. Non sistemare l’unità su amplificatori o altri dispositivi che possono diventare caldi.
Questa unità è progettata per un uso continuo. Per spegnere completamente l’unità, scollegare il connettore CA dalla presa di rete. Scollegare l’unità dalla presa se si prevede di non utilizzarla per un periodo prolungato.
2.
Durante i temporali, scollegare la spina di alimentazione dalla presa. I picchi di alta tensione provocati dai fulmini potrebbero danneggiare l’unità.
3.
Non esporre l’unità alla luce diretta del sole o ad altre fonti di calore. Questo potrebbe causare il surriscaldamento e il malfunzionamento dell’unità.
4.
Tenere il prodotto lontano da fonti di umidità
(ad es. vasi) e calore eccessivo (ad es. fuoco) o da apparecchi che generano un forte campo magnetico o elettrico. In caso di malfunzionamento dell’unità, scollegare il cavo di alimentazione dalla presa di corrente.
Il prodotto non è destinato all’uso industriale.
Questo prodotto è destinato esclusivamente all’uso personale. Se il prodotto o il disco vengono conservati a basse temperature, potrebbe formarsi della condensa.
Trasportando l’unità in inverno, attendere circa 2 ore prima di utilizzarla, in modo che ritorni a temperatura ambiente.
ITA - iii
5.
Le batterie utilizzate con questo prodotto contengono sostanze chimiche dannose per l’ambiente. Non smaltirle con i comuni rifiuti domestici. Non gettare le batterie nel fuoco.
Non cortocircuitare, smontare o surriscaldare le batterie. Una installazione scorretta delle batterie può causarne l’esplosione. Sostituire solo con batterie dello stesso tipo o equivalenti.
INFORMAZIONI SUL
MANUALE
Il manuale utente è composto da due parti: il presente MANUALE UTENTE semplificato in formato cartaceo e un MANUALE COMPLETO dettagliato che è possibile scaricare.
MANUALE UTENTE
Consultare questo manuale per istruzioni di sicurezza, informazioni sull’installazione del prodotto, i componenti, i collegamenti e le specifiche del prodotto.
MANUALE COMPLETO
È possibile accedere al MANUALE COMPLETO nel centro di assistenza clienti Samsung online scansionando il codice QR. Per visualizzare il manuale sul proprio PC o dispositivo mobile, scaricarlo dal sito Web Samsung in formato documento.
(http://www.samsung.com/support)
Le caratteristiche e le specifiche sono soggette a modifiche senza preavviso.
SOMMARIO
01 Verifica dei componenti 2
Inserimento delle batterie prima dell’utilizzo del telecomando
02 Panoramica del prodotto
3
Pannello anteriore / Pannello superiore della Soundbar
Pannello inferiore della Soundbar
03 Collegamento della Soundbar
5
04
Collegamento alla rete elettrica
Connessione della Soundbar al Subwoofer
– Connessione automatica tra il subwoofer e la Soundbar
– Connessione manuale del subwoofer in caso di connessione automatica non riuscita
Collegamento del kit SWA-8500S (venduto separatamente) alla
Collegamento alla TV
Metodo 1. Collegamento mediante un cavo
– Collegamento di una TV tramite un cavo HDMI
– Collegamento tramite un cavo ottico
Metodo 2. Connessione wireless
– Connessione di una TV mediante Bluetooth
05 Collegamento di un dispositivo esterno
10
15
Collegamento tramite un cavo HDMI
Collegamento tramite un cavo ottico
06 Collegamento di un dispositivo di memoria USB
17
ITA - iv
07 Connessione di un dispositivo mobile
08 Utilizzo del telecomando
Come utilizzare il telecomando
Regolazione del volume della Soundbar tramite il telecomando di una TV
Utilizzo dei pulsanti nascosti (pulsanti con più di una funzione)
Specifiche di uscita per diverse modalità di effetti sonori
09 Installazione del supporto a parete
Precauzioni per l’installazione
Componenti per il montaggio a parete
10 Collocamento della Soundbar sul piedistallo di una TV
11 Aggiornamento del software
Se non compare la scritta UPDATE
12 Risoluzione dei problemi
13 Licenza
14 Avviso di licenza open source
15 Nota importante sul servizio
16 Specifiche e guida
18
22
27
29
30
32
33
33
33
34
ITA - v
01 VERIFICA DEI COMPONENTI
PAIR
VOL WOOFER
SOUNDBAR
Unità principale della Soundbar Subwoofer Telecomando / Batterie
x 2
Cavo di alimentazione
(Subwoofer, Soundbar)
Adattatore CA/CC
(Soundbar)
x 2
Rondella di fissaggio
x 2
Cavo HDMI
Guida per il montaggio a parete Supporto per montaggio a parete
Vite
x 2
• Per ulteriori informazioni sull’alimentazione e il consumo di energia, vedere l’etichetta applicata al prodotto. (Etichetta : Fondo dell’Unità Principale della Soundbar)
• Per acquistare componenti aggiuntivi o cavi opzionali, contattare un Centro servizi Samsung o l’Assistenza clienti Samsung.
• L’aspetto degli accessori può variare leggermente dalle illustrazioni riportate sopra.
Inserimento delle batterie prima dell’utilizzo del telecomando
(2 batterie AA)
Far scorrere il coperchio posteriore nella direzione della freccia fino alla completa rimozione.
Inserire 2 batterie AA (1,5 V) orientate in maniera tale da rispettarne la polarità. Far scorrere il coperchio posteriore fino al raggiungimento della posizione iniziale.
ITA - 2
02 PANORAMICA DEL PRODOTTO
Pannello anteriore / Pannello superiore della Soundbar
Posizionare il prodotto in modo tale che il logo
SAMSUNG si trovi nella parte superiore.
Pannello superiore
Visualizzazione
Consente di visualizzare lo stato e il modo attuale del prodotto.
Tasto (Alimentazione)
Consente di accendere e spegnere il dispositivo.
•
Funzione Auto Power Down
L’unità si spegne automaticamente nelle situazioni elencate di seguito.
– Modalità
D.IN
/
HDMI
/
BT
/
USB
: Se non è presente un segnale audio per 20 minuti.
Tasto -/+ (Volume)
Consente di regolare il volume.
• Una volta effettuata la regolazione, il livello del volume viene visualizzato sul display frontale della Soundbar.
Tasto (Sorgente)
Consente di selezionare il modo di ingresso della sorgente.
Modo di ingresso
Ingresso digitale ottico
Ingresso ARC (HDMI OUT)
Ingresso HDMI
Modo BLUETOOTH
Modo USB
D.IN
Visualizzazione
D.IN
TV ARC (Conversione automatica)
HDMI
BT
USB
• Per attivare il modo “
BT PAIRING
”, cambiare la sorgente passando al modo “
BT
”, quindi tenere premuto il tasto
(Sorgente)
per almeno 5 secondi.
• Quando si inserisce il cavo CA, il tasto di accensione diventa operativo in 4 - 6 secondi.
• Quando si accende l’unità vi è un ritardo di 4 - 5 secondi prima che venga riprodotto il suono.
• Per attivare solo l’audio del Soundbar, disattivare i diffusori della TV nel menu di configurazione audio della TV. Vedere il manuale fornito con il televisore.
ITA - 3
Pannello inferiore della Soundbar
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
DC 24V
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
Collegare a un dispositivo USB per riprodurre file musicali sul dispositivo USB tramite la Soundbar.
DC 24V (Ingresso alimentazione)
Collegare l’adattatore CA/CC.
HDMI
Consente l’ingresso di segnali audio e video contemporaneamente utilizzando un cavo HDMI.
Collegare all’uscita HDMI di un dispositivo esterno.
HDMI TO TV (ARC)
Collegare alla presa jack HDMI (ARC) di una TV.
DIGITAL AUDIO IN (OPTICAL)
Collegare all’uscita digitale (ottica) di un dispositivo esterno.
• Quando si disconnette il cavo di alimentazione dell’adattatore CA/CC da una presa a muro, tirare la spina. Non tirare il cavo.
• Non collegare questa unità o altri componenti a una presa CA fino a quanto tutti i collegamenti tra i componenti sono stati completati.
ITA - 4
03 COLLEGAMENTO DELLA SOUNDBAR
Collegamento alla rete elettrica
Per collegare il subwoofer e la Soundbar a una presa elettrica, utilizzare i componenti di alimentazione nel seguente ordine:
1.
Collegare il cavo di alimentazione al subwoofer.
2.
Collegare il cavo di alimentazione in uscita all’adattatore di corrente, quindi alla Soundbar.
3.
Collegare il cavo di alimentazione a una presa a muro.
Vedere le figure sottostanti.
• Per ulteriori informazioni sulla potenza elettrica assorbita e sul consumo di energia, vedere l’etichetta applicata al prodotto. (Etichetta: Fondo dell’unità principale della Soundbar)
POWER
Cavo di alimentazione
Cavo di alimentazione
DC 24V
Collegamento alla rete elettrica
Adattatore CA/CC
USB (5V 0.5A)
DC 24V
Fondo dell’unità principale della Soundbar
Retro del subwoofer
Collegamento alla rete elettrica
• Assicurarsi di poggiare l’adattatore CA/CC orizzontalmente su un tavolo o sul pavimento. Se si posiziona l’adattatore CA/CC in modo che penda con l’ingresso del cavo CA rivolto verso l’alto, acqua o altre sostanze estranee potrebbero penetrare nell’adattatore e causarne il malfunzionamento.
ITA - 5
Connessione della Soundbar al Subwoofer
Quando è collegato il subwoofer, vengono riprodotti potenti toni bassi.
Connessione automatica tra il subwoofer e la Soundbar
Al momento dell’accensione dopo il collegamento dei cavi di alimentazione alla Soundbar e al subwoofer, il subwoofer si connette automaticamente alla Soundbar.
• Una volta completata l’associazione automatica, si accendono gli indicatori blu sul retro del subwoofer.
Indicatori LED sul retro del subwoofer
LED
Blu
Rosso
Rosso e blu
Stato
Acceso
Descrizione
Connessione riuscita
(funzionamento normale)
-
Soluzione
Lampeggiante
Acceso
Ripristino della connessione
Standby (con l’unità principale della Soundbar spenta)
Connessione non riuscita
Lampeggiante Malfunzionamento
Controllare che il cavo di alimentazione connesso all’unità principale della Soundbar sia collegato correttamente oppure attendere circa 5 minuti. Se continua a lampeggiare, provare a connettere manualmente il subwoofer. Consultare la
.
Verificare che il cavo di alimentazione sia collegato correttamente all’unità principale della Soundbar.
Procedere nuovamente alla connessione.
Vedere le istruzioni relative alla connessione manuale a pagina
.
Consultare il manuale per i recapiti del
Centro servizi Samsung.
ITA - 6
Connessione manuale del subwoofer in caso di connessione automatica non riuscita
Prima di eseguire la procedura di connessione manuale descritta di seguito:
• Verificare che i cavi di alimentazione della Soundbar e del subwoofer siano collegati correttamente.
• Assicurarsi che la Soundbar sia accesa.
1.
Tenere premuto
ID SET
sul retro del subwoofer per almeno 5 secondi.
• L’indicatore rosso sul retro del diffusore si spegne e l’indicatore blu lampeggia.
5 Sec
Retro del subwoofer
2.
Tenere premuto il tasto
Su
del telecomando per almeno 5 secondi.
• Il messaggio
ID SET
viene visualizzato brevemente sul display della Soundbar, poi scompare.
• La Soundbar si accenderà automaticamente una volta completata l’
ID SET
.
PAIR
5 Sec
Il logo SAMSUNG si trova sulla parte superiore
ID SET
SOUN
D
MOD
E
3.
Verificare che il LED LINK sia di colore blu fisso (connessione completata).
L’indicatore a LED LINK smette di lampeggiare e diventa blu fisso quando si stabilisce una connessione tra la Soundbar e il subwoofer wireless.
Blu fisso
ITA - 7
NOTE
• Non collegare il cavo di alimentazione di questo prodotto o la tua TV a una presa a muro fino a quanto tutti i collegamenti tra i componenti sono stati completati.
• Prima di spostare o installare questo prodotto, assicurarsi di spegnerlo e scollegare il cavo di alimentazione.
• Se l’unità principale è spenta, il subwoofer wireless entrerà in modo stand-by e l’indicatore Led di
STANDBY sul retro diventerà rosso dopo aver lampeggiato in blu per diverse volte.
• Se si utilizza un dispositivo che sfrutta la medesima frequenza (5,8 GHz) della Soundbar nelle vicinanze della Soundbar, le interferenze potrebbero causare alcune interruzioni del suono.
• La distanza di trasmissione massima del segnale wireless dell’unità principale è di circa 10 metri, ma può variare a seconda dell’ambiente di funzionamento. Se tra l’unità principale e il subwoofer si frappone una parete metallica o di cemento armato, il sistema potrebbe non funzionare affatto in quanto il segnale wireless non è in grado di attraversare il metallo.
PRECAUZIONI
• Le antenne di ricezione wireless sono integrate nel subwoofer wireless. Tenere le unità al riparo da acqua e umidità.
• Per prestazioni di ascolto ottimali, assicurarsi che l’area circostante il diffusore wireless e il posizionamento del modulo di ricezione wireless (venduto separatamente) siano sgombri da ostacoli.
Collegamento del kit SWA-8500S (venduto separatamente) alla
Soundbar
Per provare il vero impianto audio surround wireless, collegare il kit di diffusori posteriori wireless
Samsung (SWA-8500S, venduto separatamente) alla Soundbar.
1.
Collegare il modulo ricevitore wireless ai 2 diffusori surround.
– Il cavi dei diffusori sono identificati tramite un codice colore.
SURROUND-LEFT
SURROUND-LEFT
L
L R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
ID SET
R
SURROUND SPEAKERS OUT
ID SET
SURROUND-RIGHT
SURROUND-RIGHT
ITA - 8
2.
Dopo aver inserito il modulo ricevitore wireless in una presa elettrica, verificare che sia in stato di standby.
• L’indicatore LINK a LED (LED blu) sul Modulo ricevitore wireless lampeggia. Se il LED non lampeggia, premere il tasto
ID SET
sul retro del Modulo ricevitore wireless con la punta di una penna per 5~6 secondi fino a che l’indicatore LINK a LED lampeggia (in blu). Per ulteriori informazioni sul LED, fare riferimento al manuale utente del prodotto SWA-8500S.
SURROUND SPEAKERS OUT
R
5 Sec
ID SET
ID SET
STANDBY
LINK
STANDBY
LINK
POWER
Blu lampeggiante
POWER
3.
Tenere premuto il tasto
Su
del telecomando per almeno 5 secondi.
• Il messaggio
ID SET
viene visualizzato brevemente sul display della Soundbar, poi scompare.
• La Soundbar si accenderà automaticamente una volta completata l’
ID SET
.
PAIR
5 Sec
Il logo SAMSUNG si trova sulla parte superiore
ID SET
SOUN
D
MOD
E
ATTENZIONE
• Se la Soundbar stava riproducendo musica al momento del collegamento al kit SWA-8500S, potrebbero udirsi alcune irregolarità emesse dal woofer durante il completamento della connessione.
4.
Verificare che il LED LINK sia di colore blu fisso (connessione completata).
STANDBY
LINK
STANDBY
LINK
L’indicatore a LED LINK smette di lampeggiare e diventa blu fisso quando si stabilisce una connessione tra la Soundbar e il modulo ricevitore wireless.
Blu fisso
5.
Se il kit SWA-8500S non si connette, ripetere la procedura dal passaggio 2.
ITA - 9
04 COLLEGAMENTO ALLA TV
È possibile ascoltare l’audio della TV dalla Soundbar grazie a connessioni cablate o wireless.
• Quando la Soundbar è collegata a specifici modelli di televisore Samsung, è possibile controllarla utilizzando il telecomando della TV.
– Questa funzione è supportata dalle Smart TV Samsung del 2017 e successive che sono in grado di supportare il Bluetooth quando si collega la Soundbar alla TV con un cavo ottico.
– Questa funzione consente inoltre di utilizzare il menu della TV per regolare il campo sonoro e diverse impostazioni, oltre al volume e alla funzione di muto.
Metodo 1. Collegamento mediante un cavo
Quando i segnali di radiodiffusione sono di tipo Dolby Digital e nella TV il “Formato audio dell’uscita digitale” è impostato su PCM, si raccomanda di modificare l’impostazione passando a Dolby Digital.
Una volta modificata l’impostazione, è possibile godere di una qualità audio più elevata. (Sul menu del
TV le diciture per Dolby Digital e PCM potrebbero essere diverse a seconda del produttore del TV.)
Collegamento di una TV tramite un cavo HDMI
Verificare la presenza del
(ARC) presso la porta
HDMI IN della propria TV.
Cavo HDMI
Fondo della Soundbar
HDMI IN
(ARC)
Verificare la porta HDMI TO TV (ARC) dell'unità principale della Soundbar.
Parte superiore della Soundbar
TV ARC
1.
Con la Soundbar e la TV accese, collegare il cavo HDMI come illustrato nella figura.
2.
“
TV ARC
” compare nella finestra di visualizzazione dell’unità principale della Soundbar e la
Soundbar riproduce l’audio della TV.
ITA - 10
• Se l’audio della TV è inudibile, premere il tasto
(Sorgente)
sul telecomando o sulla parte superiore della Soundbar per passare al modo “
D.IN
”. Sullo schermo vengono visualizzati “
D.IN
” e “
TV ARC
” n sequenza e viene riprodotto l’audio della TV.
• Se “
TV ARC
” non compare nella finestra di visualizzazione dell’unità principale della Soundbar, verificare che il cavo HDMI sia collegato alla porta corretta.
• Utilizzare i tasti del volume del telecomando della TV per regolare il volume della Soundbar.
NOTE
• L’HDMI è un’interfaccia che permette la trasmissione digitale di dati audio e video con un singolo connettore.
• Se la TV è dotata di una porta ARC, collegare il cavo HDMI all’ingresso HDMI IN (ARC).
• Consigliamo l’uso di un cavo HDMI coreless, se possibile. Se si utilizza un cavo HDMI cored, usarne uno il cui diametro sia inferiore ai 14 mm.
• Questa funzione non è disponibile, se il cavo HDMI non supporta l’ARC.
Collegamento tramite un cavo ottico
Fondo della Soundbar
Cavo ottico
(non fornito in dotazione)
DIGITAL AUDIO IN (OPTICAL)
Parte superiore della Soundbar
OPTICAL OUT
D.IN
1.
Collegare la presa jack
DIGITAL AUDIO IN (OPTICAL)
della Soundbar alla presa jack OPTICAL OUT della TV con un cavo ottico (non fornito in dotazione) digitale.
2.
Premere il tasto
(Sorgente)
sul pannello superiore o sul telecomando, quindi selezionare il modo “
D.IN
”.
ITA - 11
Utilizzo della funzione Q-Symphony
Per Q-Symphony, la Soundbar si sincronizza con un TV Samsung per emettere l’audio attraverso due dispositivi per un effetto surround ottimale. Quando la Soundbar è connessa, viene visualizzato il menu
“
TV+Soundbar
” nel menu
Uscita audio
del TV. Selezionare il menu corrispondente.
Menu del TV
Cavo HDMI
OPPURE
D.IN
Cavo ottico (non fornito in dotazione)
• Esempio di menu del TV:
TV Nome serie + [AV] Soundbar Nome serie (HDMI)
NOTE
• Può funzionare a seconda del Codec supportato dal TV.
• Questa funzione è supportata solo quando è collegato il cavo HDMI o il cavo ottico (non fornito in dotazione).
• Questa funzione è disponibile nei TV Samsung rilasciati nel 2020 e in alcuni modelli di Soundbar.
ITA - 12
Metodo 2. Connessione wireless
Connessione di una TV mediante Bluetooth
In caso di connessione di una TV mediante Bluetooth, è possibile percepire l’audio stereo senza i fastidi dovuti al cablaggio.
• È possibile connettere solo una TV alla volta.
PAIR
OPPURE
D
MOD
E
La connessione iniziale
1.
Premere il tasto
PAIR
sul telecomando per accedere alla modalità “
BT PAIRING
”.
(OPPURE)
a.
Premere il tasto
(Sorgente)
sul pannello superiore, quindi selezionare “
BT
”.
“
BT
” passa automaticamente in pochi secondi a “
BT PAIRING
” oppure a “
BT READY
” se presente un record di connessione.
b.
Quando compare “
BT READY
”, tenere premuto il tasto
(Sorgente)
nel pannello superiore della Soundbar per più di 5 secondi per visualizzare “
BT PAIRING
”.
2.
Selezionare il modo Bluetooth sulla TV. (Per ulteriori informazioni, consultare il manuale della TV.)
3.
Selezionare “
[AV] Samsung Soundbar Q6T-Series
” dall’elenco visualizzato nella schermata della
TV. Una Soundbar disponibile è indicata con “
Need Pairing
” o “
Paired
” nell’elenco dei dispositivi
Bluetooth della TV. Per connettersi alla Soundbar, selezionare il messaggio e stabilire una connessione.
• Una volta connessa la TV, viene visualizzato il messaggio [
Nome TV
] → “
BT
” sul display frontale della Soundbar.
4.
Ora è possibile percepire l’audio della TV dalla Soundbar.
Se il dispositivo non riesce a connettersi
• Se la voce relativa alla Soundbar precedentemente connessa (ad es. “
[AV] Samsung Soundbar
Q6T-Series
”) compare nell’elenco, cancellatela.
• Ripetere quindi i passaggi da 1 a 3.
NOTA
• Una volta connessa la Soundbar alla TV per la prima volta, utilizzare la modalità “
BT READY
” per la riconnessione.
ITA - 13
Disconnessione della Soundbar dalla TV
Premere il tasto
(Sorgente)
sul pannello superiore o sul telecomando, quindi passare a un modo qualsiasi eccetto “
BT
”.
• La disconnessione richiede tempo perché la TV deve ricevere una risposta dalla Soundbar. (Il tempo necessario potrebbe variare a seconda del modello di TV.)
• Per annullare la connessione Bluetooth automatica tra la Soundbar e il TV, premere il tasto
Sinistra
del telecomando per 5 secondi con la Soundbar in stato “
BT READY
”. (Attivazione → Disattivazione)
Qual è la differenza tra BT READY e BT PAIRING?
•
BT READY
: in questa modalità è possibile cercare delle TV già connesse in passato o connettere alla Soundbar un dispositivo mobile connesso in passato.
•
BT PAIRING
: in questa modalità, è possibile connettere un nuovo dispositivo alla Soundbar.
(Premere il tasto
PAIR
sul telecomando o tenere premuto il tasto
(Sorgente)
nella parte superiore della Soundbar per più di 5 secondi mentre la Soundbar è in modo “
BT
”.)
NOTE
• Se viene richiesto un codice PIN durante la connessione a un dispositivo Bluetooth, immettere
<0000>.
• Nel modo di connessione Bluetooth, la connessione Bluetooth viene persa se la distanza tra la
Soundbar e il dispositivo Bluetooth supera i 10 m.
• La Soundbar si spegne automaticamente dopo 20 minuti nello stato Pronto.
• La Soundbar potrebbe non essere in grado di effettuare la ricerca o la connessione Bluetooth correttamente nelle seguenti condizioni:
– Se la Soundbar è circondata da un potente campo elettrico.
– Se due o più dispositivi Bluetooth sono associati contemporaneamente alla Soundbar.
– Se il dispositivo Bluetooth è spento, fuori posto o presenta malfunzionamenti.
• I dispositivi elettronici potrebbero causare interferenze radio. I dispositivi che generano onde elettromagnetiche, come ad esempio forni a microonde, LAN wireless e così via, devono essere tenuti lontano dall’unità principale della Soundbar.
ITA - 14
05 COLLEGAMENTO DI UN DISPOSITIVO
ESTERNO
È possibile connettere un dispositivo esterno tramite una connessione cablata o Bluetooth per riprodurne l’audio attraverso la Soundbar.
Collegamento tramite un cavo HDMI
Fondo della Soundbar
HDMI OUT
HDMI
Dispositivo esterno
Cavo HDMI
HDMI IN
(ARC)
Cavo HDMI
Parte superiore della Soundbar
HDMI
1.
Collegare un cavo HDMI dalla presa jack
HDMI
, situata sul retro del prodotto, alla presa jack HDMI
OUT del dispositivo digitale.
2.
Collegare un cavo HDMI dalla presa jack
HDMI TO TV (ARC)
, situata sul retro del prodotto, alla presa jack HDMI IN della TV.
3.
Premere il tasto
(Sorgente)
sul pannello superiore o sul telecomando, quindi selezionare
“
HDMI
”.
4.
Il modo “
HDMI
” è visualizzato sul pannello display della Soundbar e l’audio viene riprodotto.
ITA - 15
Collegamento tramite un cavo ottico
Fondo della Soundbar
HDMI TO TV
(ARC)
Cavo ottico
(non fornito in dotazione)
DIGITAL AUDIO IN (OPTICAL)
Parte superiore della Soundbar
OPTICAL OUT
Lettore BD / DVD /
Decoder /
Console per videogiochi
D.IN
1.
Collegare il
DIGITAL AUDIO IN (OPTICAL)
ell’unità principale alla presa jack OPTICAL OUT del dispositivo sorgente utilizzando un cavo ottico (non fornito in dotazione) digitale.
2.
Selezionare il modo “
D.IN
” premendo il tasto
(Sorgente)
sul pannello superiore o sul telecomando.
ITA - 16
06 COLLEGAMENTO DI UN DISPOSITIVO DI
MEMORIA USB
È possibile riprodurre tramite la Soundbar file musicali contenuti in dispositivi di memoria.
USB (5V 0.5A)
DC 24V
Porta USB
HDMI
HDMI TO TV
(ARC)
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
USB
1.
Connettere il dispositivo USB alla porta USB nella parte inferiore del prodotto.
2.
Premere il tasto
(Sorgente)
sul pannello superiore o sul telecomando, quindi selezionare “
USB
”.
3.
Nel display viene visualizzato “
USB
”.
4.
Riprodurre file musicali dal dispositivo di memoria tramite la Soundbar.
• La Soundbar si spegne automaticamente (Auto Power Down) se non è stato collegato alcun dispositivo USB per più di 20 minuti.
Elenco della compatibilità
Estensione
*.mp3
Codec
MPEG1 Layer2
MPEG1 Layer3
MPEG2 Layer3
MPEG2.5 Layer3
WMA7/8/9 (solo audio)
Vorbis
Frequenza di campionamento
32 kHz ~ 48 kHz
32 kHz ~ 48 kHz
16 kHz ~ 24 kHz
8 kHz ~ 12 kHz
32 kHz ~ 48 kHz
32 kHz ~ 48 kHz
Velocità di trasmissione
32 ~ 320 kbps
32 ~ 320 kbps
8 ~ 160 kbps
8 ~ 160 kbps
32 ~ 320 kbps
45 ~ 500 kbps
*.wma
*.ogg
*.aac
*.m4a
*.mp4
*.wav
*.flac
*.aiff
AAC-LC
(MPEG2/MPEG4 solo audio)
LPCM
FLAC
AIFF
32 kHz ~ 48 kHz
32 kHz ~ 192 kHz
32 kHz ~ 192 kHz
32 kHz ~ 192 kHz
32 ~ 320 kbps
1024 ~ 9216 kbps
162 ~ 8100 kbps
1024 ~ 9216 kbps
• Se nel dispositivo USB sono presenti troppi file e cartelle, la Soundbar potrebbe impiegare qualche istante per l’accesso a e la riproduzione dei file.
ITA - 17
07 CONNESSIONE DI UN DISPOSITIVO MOBILE
Connessione tramite Bluetooth
In caso di connessione di un dispositivo mobile mediante Bluetooth, è possibile percepire l’audio stereo senza i fastidi dovuti al cablaggio.
• La connessione è limitata a una TV o a due dispositivi Bluetooth contemporaneamente.
PAIR
OPPURE
Dispositivo Bluetooth
D
MOD
E
La connessione iniziale
1.
Premere il tasto
PAIR
sul telecomando per accedere alla modalità “
BT PAIRING
”.
(OPPURE)
a.
Premere il tasto
(Sorgente)
sul pannello superiore, quindi selezionare “
BT
”.
“
BT
” passa automaticamente in pochi secondi a “
BT PAIRING
” oppure a “
BT READY
” se presente un record di connessione.
b.
Quando compare “
BT READY
”, tenere premuto il tasto
(Sorgente)
nel pannello superiore della Soundbar per più di 5 secondi per visualizzare “
BT PAIRING
”.
2.
Selezionare “
[AV] Samsung Soundbar Q6T-Series
” all’elenco visualizzato.
• Quando una Soundbar è connessa al dispositivo Bluetooth, nel display frontale viene visualizzato il messaggio [
Nome dispositivo Bluetooth
] → “
BT
”.
3.
Riprodurre file musicali dal dispositivo, connesso tramite Bluetooth, tramite la Soundbar.
Se il dispositivo non riesce a connettersi
• Se la voce relativa alla Soundbar precedentemente connessa (ad es. “
[AV] Samsung Soundbar
Q6T-Series
”) compare nell’elenco, cancellatela.
• Quindi ripetere i passaggi 1 e 2.
NOTA
• Una volta connessa la Soundbar alla dispositivo mobile per la prima volta, utilizzare la modalità
“
BT READY
” per la riconnessione.
ITA - 18
Qual è la differenza tra BT READY e BT PAIRING?
•
BT READY
: in questa modalità è possibile cercare delle TV già connesse in passato o connettere alla Soundbar un dispositivo mobile connesso in passato.
•
BT PAIRING
: in questa modalità, è possibile connettere un nuovo dispositivo alla Soundbar
(Premere il tasto
PAIR
sul telecomando o tenere premuto il tasto
(Sorgente)
nella parte superiore della Soundbar per più di 5 secondi mentre la Soundbar è in modo “
BT
”.)
NOTE
• Se viene richiesto un codice PIN durante la connessione a un dispositivo Bluetooth, immettere
<0000>.
• Nel modo di connessione Bluetooth, la connessione Bluetooth viene persa se la distanza tra la
Soundbar e il dispositivo Bluetooth supera i 10 m.
• La Soundbar si spegne automaticamente dopo 20 minuti nello stato Pronto.
• La Soundbar potrebbe non essere in grado di effettuare la ricerca o la connessione Bluetooth correttamente nelle seguenti condizioni:
– Se la Soundbar è circondata da un potente campo elettrico.
– Se si effettua l’associazione di diversi dispositivi Bluetooth con la Soundbar in contemporanea.
– Se il dispositivo Bluetooth è spento, fuori posto o presenta malfunzionamenti.
• I dispositivi elettronici potrebbero causare interferenze radio. I dispositivi che generano onde elettromagnetiche, come ad esempio forni a microonde, LAN wireless e così via, devono essere tenuti lontano dall’unità principale della Soundbar.
• Il Soundbar supporta i dati SBC (44,1kHz, 48kHz).
• Effettuare il collegamento esclusivamente a un dispositivo Bluetooth che supporti la funzione
A2DP (AV).
• Non è possibile collegare il Soundbar a un dispositivo Bluetooth che supporta soltanto la funzione
HF (Hands Free).
• Una volta stabilito il collegamento tra la Soundbar e un dispositivo Bluetooth, selezionando
“
[AV] Samsung Soundbar Q6T-Series
” dall’elenco dei dispositivi trovati, la Soundbar passa automaticamente al modo “
BT
”.
– Disponibile solo se il Soundbar è elencato tra i dispositivi collegati al dispositivo Bluetooth.
(Il dispositivo Bluetooth e il Soundbar devono essere stati collegati in precedenza almeno una volta).
• Il Soundbar appare nell’elenco dei dispositivi cercati del dispositivo Bluetooth solo se il Soundbar visualizza “
BT READY
”.
Accensione Bluetooth Power (SOUND MODE)
Quando la funzione Accensione Bluetooth Power è attivata e il Soundbar è spento, se un dispositivo
Bluetooth collegato in precedenza prova a collegarsi al Soundbar, il Soundbar si accende automaticamente.
1.
Tenere premuto il tasto
SOUND MODE
sul telecomando per più di 5 secondi mentre si accende la
Soundbar.
2.
“
ON-BLUETOOTH POWER
” viene visualizzato sul display della Soundbar.
ITA - 19
Disconnettere il dispositivo Bluetooth dalla Soundbar
È possibile scollegare il dispositivo Bluetooth dall’Soundbar. Per le istruzioni, vedere il manuale utente del dispositivo Bluetooth.
• L’Soundbar viene scollegato.
• Una volta disconnessa la Soundbar dal dispositivo Bluetooth, nel suo display frontale verrà visualizzato il messaggio “
BT DISCONNECTED
”.
Disconnessione della Soundbar dal dispositivo Bluetooth
Premere il tasto
(Sorgente)
sul pannello superiore o sul telecomando, quindi passare a un modo qualsiasi eccetto “
BT
”.
• La disconnessione richiede tempo perché il dispositivo Bluetooth deve ricevere una risposta dalla
Soundbar. (Il tempo di disconnessione potrebbe variare a seconda del dispositivo Bluetooth)
• Una volta disconnessa la Soundbar dal dispositivo Bluetooth, nel suo display frontale verrà visualizzato il messaggio “
BT DISCONNECTED
”.
NOTE
• In modo di connessione Bluetooth, la connessione cade se la distanza tra l’Soundbar e il dispositivo
Bluetooth supera 10 m.
• L’Soundbar si spegne automaticamente dopo 20 minuti in modo Pronto.
Ulteriori informazioni sul Bluetooth
Bluetooth è una tecnologia che permette di collegare facilmente tra di loro dispositivi compatibili con
Bluetooth attraverso una connessione wireless a breve raggio.
• Il dispositivo Bluetooth può provocare rumorosità o malfunzionamenti, a seconda delle condizioni di utilizzo, se:
– Una parte del corpo è a contatto con il sistema di ricezione / di trasmissione del dispositivo
Bluetooth o dell’Soundbar.
– È soggetto a variazioni elettriche dovute a interferenze derivanti da riflessioni dei segnali su pareti, spigoli o tramezzature d’ufficio.
– È esposto a interferenze elettriche derivanti da dispositivi della stessa banda di frequenza, incluse apparecchiature mediche, forni a microonde e LAN wireless.
• Collegare l’Soundbar al dispositivo Bluetooth mantenendo una distanza ravvicinata.
• Maggiore è la distanza tra l’Soundbar e il dispositivo Bluetooth, peggiore è la qualità.
Se la distanza supera il raggio d’azione del Bluetooth, la connessione si interrompe.
• In aree a bassa sensibilità di ricezione, la connessione Bluetooth potrebbe non funzionare correttamente.
• Il collegamento Bluetooth funziona solo nelle vicinanze del dispositivo. La connessione viene automaticamente interrotta se la distanza è superiore a questo limite. La qualità del suono si riduce in presenza di ostacoli quali pareti o porte, anche entro il limite indicato.
• Questo dispositivo wireless potrebbe causare interferenze elettriche durante il suo funzionamento.
ITA - 20
Connessione multipla Bluetooth
La Soundbar può essere connessa a 2 dispositivi Bluetooth contemporaneamente.
Dispositivo Bluetooth A Dispositivo Bluetooth B
1.
Connettere la Soundbar a un massimo di due dispositivi Bluetooth. (Consultare la pagina 18)
2.
Riprodurre la musica da uno dei dispositivi Bluetooth connessi mentre ne sono connessi due.
3.
Per riprodurre la musica dal dispositivo Bluetooth “B” durante la riproduzione dal dispositivo “A”, mettere in pausa o arrestare la riproduzione dal dispositivo “A”, quindi avviare la riproduzione dal dispositivo “B”.
• Non verrà cambiato dispositivo se la musica verrà riprodotta dal dispositivo “B” senza aver prima messo in pausa o arrestato il dispositivo “A”.
4.
Nelle versioni precedenti ad AVRCP V1.4, il tempo necessario per passare da un dispositivo che riproduce la musica all’altro potrebbe essere maggiore.
NOTE
• Se si cerca di connettere un 3° dispositivo Bluetooth, uno tra i dispositivi A o B verrà disconnesso.
(Verrà disconnesso un dispositivo non attualmente in fase di riproduzione.)
• È possibile connettere solo un TV Samsung o 2 dispositivi Bluetooth contemporaneamente.
• La Soundbar verrà disconnessa dai dispositivi Bluetooth se riceverà una richiesta di connessione da una TV Samsung.
ITA - 21
08 UTILIZZO DEL TELECOMANDO
Come utilizzare il telecomando
SOUND
MODE
PAIR
VOL WOOFER
SOUNDBAR
Consente di accendere e spegnere la Soundbar.
VOL
Alimentazione
Premere per selezionare una sorgente collegata alla Soundbar.
Sorgente
Premere il tasto
(Muto)
per disattivare
Muto
SOUND
MODE
SOUND MODE
PAIR
BASS desiderato scegliendo tra
STANDARD
,
SURROUND SOUND
,
GAME PRO
,
ADAPTIVE
SOUND
o
DTS VIRTUAL:X
.
–
STANDARD
Emette l’audio originale.
–
SURROUND SOUND
VOL
BASS
–
BASS quello standard.
GAME PRO
Fornisce l’audio stereoscopico che consente la piena immersione nell’azione di gioco.
–
ADAPTIVE SOUND
Analizza il contenuto in tempo reale e fornisce automaticamente il campo sonoro ottimale in base alle caratteristiche del
VOL BASS
–
DTS VIRTUAL:X
Audio 3D immersivo da qualsiasi contenuto.
ITA - 22
VOL
PAIR
SOUND
MODE
Bluetooth
PAIR
•
DRC (Dynamic Range Control)
Consente di applicare il controllo della gamma dinamica alle tracce Dolby Digital.
Tenere premuto il tasto
SOUND MODE
mentre la Soundbar è spenta per attivare o disattivare il DRC (Dynamic Range Control). Se DRC è acceso, si riduce il volume dell’audio. (L’audio potrebbe essere distorto.)
•
Bluetooth Power
Questa funzione accende automaticamente la Soundbar nel momento in cui riceve una richiesta di connessione da una TV o da un dispositivo Bluetooth già connessi in passato.La funzione è Attiva per impostazione predefinita.
– Tenere premuto il tasto
SOUND MODE
per più di 5 secondi per disattivare la funzione Bluetooth Power.
Premere il tasto
PAIR
. Sul display della Soundbar viene visualizzato “
BT PAIRING
”.
In questa modalità è possibile connettere la Soundbar a un nuovo dispositivo Bluetooth selezionando la Soundbar dall’elenco di ricerca del dispositivo Bluetooth.
Premere il tasto
p
per sospendere temporaneamente la riproduzione di un file musicale.
Premendo nuovamente il tasto, si riavvia la riproduzione
Riproduci /
Sospendi
BASS
PAIR
SOUND
MODE
Su/Giù/
Sinistra/
PAIR
VOL
VOL
Premere le aree indicate per selezionare Su/Giù/Sinistra/
Destra.
BASS
BASS
Premere Su/Giù/Sinistra/Destra sul tasto per selezionare o impostare funzioni.
•
Ripeti
Per utilizzare la funzione Ripeti nel modo “
USB
”, premere il tasto
Su
.
•
Salta brano
Premere il tasto
Destra
per selezionare il file musicale successivo. Premere il tasto
Sinistra
per selezionare il file musicale precedente.
•
ID SET
Tenere premuto il tasto
Su
per 5 secondi per completare l’
ID SET
(in caso di connessione a un elemento accessorio).
ITA - 23
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
VOL
•
Funzione di limitazione del volume
Per proteggere l’udito dell’utente, la funzione Limitazione volume limita il volume a
20 se la Soundbar viene accesa quando il volume è più alto di 20.
– Il valore predefinito per la funzione Limitazione volume è Non attiva. Per utilizzarla è necessario attivarla.
– Se attivata, la funzione Limitazione volume rimane attiva anche se il dispositivo viene spento.
– Per attivare o disattivare la funzione Limitazione volume, tenere premuto il tasto
Giù
sul telecomando per 5 secondi. Quando la funzione Limitazione volume è disattivata, sul display anteriore verrà visualizzato “
V FREE
”. Quando la funzione è attiva, verrà visualizzato “
V LOCK
”.
Controllo audio
SOUND
MODE
PAIR
È possibile selezionare
TREBLE
,
BASS
o
AUDIO SYNC
.
• Per controllare il volume dell’audio di alti e bassi, premere il tasto
Controllo audio
per selezionare
TREBLE
o
BASS
, quindi regolare il volume tra -6~+6 utilizzando i tasti
Su/
Giù
.
• Tenere premuto il pulsante
(Controllo audio)
per circa 5 secondi per regolare il suono di ciascuna banda di frequenza. È possibile utilizzare i pulsanti
Sinistra/Destra
per selezionare 150 Hz, 300 Hz, 600 Hz, 1,2 kHz, 2,5 kHz, 5 kHz e 10 kHz e ciascuna selezione può essere regolata tra -6 e +6 mediante i pulsanti
Su/Giù
.
• Se il video della TV e l’audio della Soundbar non sono sincronizzati, premere il tasto
Controllo audio
per selezionare
AUDIO SYNC
, quindi impostare il ritardo audio tra
0~300 millisecondi utilizzando i tasti
Su/Giù
. (Non disponibile nel modo “
USB
” o “
BT
”.)
• Se sono collegati dei Diffusori surround, è possibile accendere/spegnere la funzione dei diffusori posteriori usando i tasti
Su/Giù
per regolare il volume in un intervallo compreso tra -6 e +6.
• La funzione
AUDIO SYNC
è supportata soltanto in alcune funzioni.
SOU
ND
MO
DE
VOL
PAIR
PAIR
R
WOOFE
MODE
SOUND
MODE
SOUNDB
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Far oscillare il tasto
WOOFER
avanti o indietro per regolare il volume del subwoofer a -12 o tra -6 e +6. Per impostare il volume del subwoofer su 0, premere il tasto.
VOL
VOL
BASS
BASS
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
Far oscillare il tasto
VOL
avanti o indietro per regolare il volume.
•
Muto
Premere il tasto
VOL
per disattivare l’audio. Premerlo nuovamente per riattivare l’audio.
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
ITA - 24
Regolazione del volume della
Soundbar tramite il telecomando di una TV
Se si è in possesso di una TV Samsung, è possibile regolare il volume della Soundbar utilizzando il telecomando a infrarossi fornito in dotazione con la TV Samsung.
Prima di tutto utilizzare il menu della TV Samsung per impostare l’audio della TV sui diffusori esterni, dopodiché utilizzare il telecomando Samsung per controllare il volume della Soundbar. Per ulteriori informazioni, consultare il manuale utente della
TV. La modalità predefinita per questa funzione è il controllo mediante un telecomando Samsung.
Se la propria TV non è una TV Samsung, seguire le indicazioni sotto riportate per modificare le impostazioni relative alla funzione.
1.
Spegnere la Soundbar.
BYE
2.
Se non si desidera utilizzare questa funzione, tenere premuto il tasto
WOOFER
verso l’alto per 5 secondi ripetutamente finché non viene visualizzato il messaggio “
OFF-TV
REMOTE
” nel display.
4.
Se si desidera ripristinare la modalità predefinita della Soundbar (controllo mediante il telecomando di un TV Samsung), tenere premuto verso l’alto il tasto
WOOFER
per 5 secondi ripetutamente fino a quando sul display non appare “
SAMSUNG-TV
REMOTE
”.
5 Sec
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
(Modalità predefinita)
SAMSUNG-TV REMOTE
– Ogni volta in cui si tiene premuto il tasto
WOOFER
verso l’alto per 5 secondi, la modalità cambia seguendo quest’ordine:
“
SAMSUNG-TV REMOTE
” (Modalità predefinita) → “
OFF-TV REMOTE
” →
“
ALL-TV REMOTE
”.
– Questa funzione potrebbe non essere disponibile a seconda del telecomando.
– Produttori che supportano questa funzione: VIZIO, LG, Sony, Sharp, PHILIPS,
PANASONIC, TOSHIBA, Hisense, RCA
SOU
ND
MO
DE
5 Sec
OFF-TV REMOTE
VOL
WOOFE
R
SOUNDB
AR
3.
Se si desidera controllare la Soundbar con il telecomando della propria TV, tenere premuto il tasto
WOOFER
verso l’alto per 5 secondi ripetutamente finché non viene visualizzato il messaggio “
ALL-TV REMOTE
”.
Dopodiché utilizzare il menu della propria TV per selezionare i diffusori esterni.
5 Sec
SOU
ND
MO
DE
VOL
WOOFE
R
SOUNDB
AR
ALL-TV REMOTE
ITA - 25
Utilizzo dei pulsanti nascosti (pulsanti con più di una funzione)
Tasto del telecomando
WOOFER (Su)
p
(Riproduci / Sospendi)
Sinistra
Su
Giù
(Controllo audio)
Tasto nascosto
Funzione
Acceso/Spento Telecomando della TV
(Standby)
Inizializzazione (Standby)
Accensione/Spegnimento della connessione automatica TV
(BT Pronto)
ID SET (Standby)
Acceso/Spento Limitazione del volume
(Standby)
EQ 7 bande
DRC ON/OFF (Standby)
SOUND MODE
Bluetooth Power
Pagina di riferimento
Specifiche di uscita per diverse modalità di effetti sonori
Uscita
Surround
SOUND MODE
VOL
SOUND
MODE
Effetto
STANDARD
Bluetooth
POWER
SURROUND
SOUND
GAME PRO
ADAPTIVE
SOUND
WOOFER
DTS VIRTUAL:X
Ingresso
2.0 canali
5.1 canali
2.0 canali
5.1 canali
2.0 canali
5.1 canali
2.0 canali
5.1 canali
2.0 canali
5.1 canali
Senza kit di diffusori posteriori wireless
2.1 canali
3.1 canali
4.1 canali
5.1 canali
4.1 canali
5.1 canali
4.1 canali
5.1 canali
3.1 canali
3.1 canali
Con kit di diffusori posteriori wireless
4.1 canali
5.1 canali
6.1 canali
7.1 canali
6.1 canali
7.1 canali
6.1 canali
7.1 canali
5.1 canali
5.1 canali
• È possibile acquistare il kit di diffusori posteriori wireless Samsung separatamente. Per acquistare un kit, contattare il venditore da cui avete acquistato la Soundbar.
ITA - 26
09 INSTALLAZIONE
DEL SUPPORTO A
PARETE
Componenti per il montaggio a parete
Guida per il montaggio a parete
Precauzioni per l’installazione
• Installare solamente su pareti verticali.
• Non installare in luoghi caratterizzati da alte temperature e livelli di umidità.
• Verificare che la parete sia sufficientemente robusta da sostenere il peso del prodotto. In caso contrario, provvedere a rinforzare la parete o scegliere un altro luogo di installazione.
• Acquistare e utilizzare viti e ancoraggi di fissaggio adatti alla tipologia di parete scelta
(cartongesso, ferro, legno, ecc.). Se possibile, fissare le viti di supporto ai montanti della parete.
• Acquistare viti per il montaggio a parete a seconda della tipologia e dello spessore del muro su cui si intende montare la Soundbar.
– Diametro: M5
– Lunghezza: si consiglia 35 mm o maggiore.
• Collegare i cavi dall’unità ai dispositivi esterni prima di installare la Soundbar sulla parete.
• Assicurarsi che l’unità sia spenta e scollegata dalla rete elettrica prima di installarla. In caso contrario, potrebbe provocare scosse elettriche.
x 2
Rondella di fissaggio
x 2
Vite
Supporto per montaggio a parete
1.
Posizionare la
Guida per il montaggio a parete
contro la superficie della parete.
• La
Guida per il montaggio a parete
deve essere livellata.
• Se la TV è montata sulla parete, installare la Soundbar almeno 5 cm sotto la TV.
Almeno 5 cm
x 2
ITA - 27
2.
Allineare la
Linea centrale della Guida per il montaggio a parete
con il centro della TV (in caso di montaggio della Soundbar sotto la
TV), quindi fissare la
Guida per il montaggio a parete
alla parete con del nastro adesivo.
• Se non si intende montare la Soundbar sotto una TV, posizionare la
Linea centrale
al centro dell’area di installazione.
5.
Far passare una vite (non fornita in dotazione) attraverso ciascuna
Rondella di fissaggio
, quindi avvitare saldamente ciascuna vite in un apposito foro.
6.
Installare 2
Supporto per montaggio a parete
con l’orientamento corretto sul fondo della Soundbar, utilizzando 2
Viti
.
Linea centrale
3.
Con la punta di una penna o di una matita temperata forare il centro delle immagini
A-TYPE
su ciascuna estremità della Guida per contrassegnare i punti destinati ai fori delle viti di supporto, quindi rimuovere la
Guida per il montaggio a parete
.
• Durante l’assemblaggio, assicurarsi che la parte a sospensione dei
Supporti per montaggio a parete
sia situata dietro la parte posteriore della Soundbar.
Retro della Soundbar 4.
Utilizzando una punta da trapano delle giuste dimensioni, praticare un foro nella parete in corrispondenza di ciascun segno.
• Se i segni non corrispondono alle posizioni di montanti, assicurarsi di inserire ancoraggi o tasselli appropriati nei fori prima di inserire le viti di supporto.
Se si utilizzano ancoraggi o tasselli, assicurarsi che i fori praticati siano sufficientemente grandi da accogliere gli ancoraggi o i tasselli utilizzati.
Estremità destra della Soundbar
ITA - 28
7.
Installare la Soundbar con gli annessi
Supporti per montaggio a parete
appendendo i
Supporti per montaggio a parete
alle
Rondelle di fissaggio
sulla parete.
10 COLLOCAMENTO
DELLA
SOUNDBAR SUL
PIEDISTALLO DI
UNA TV
Collocare la Soundbar sul piedistallo di una TV.
8.
Far scorrere la Soundbar verso il basso come illustrato di seguito, in modo che le
Supporto per montaggio a parete
si appoggino saldamente sulle
Rondella di fissaggio
.
• Inserire le
Rondella di fissaggio
nella parte larga (fondo) delle
Supporto per montaggio a parete
, quindi far scorrere le
Supporto per montaggio a parete
verso il basso, in modo che le
Supporto per montaggio a parete
si appoggino saldamente sulle
Rondella di fissaggio
.
3 cm o
più
Come illustrato nell’immagine, allineare il centro della Soundbar con il centro del TV, quindi, prestando la massima attenzione, posizionare la
Soundbar sul piedistallo del TV.
Per una qualità audio ottimale, posizionare la
Soundbar ad almeno 3 cm dalla parte anteriore della TV.
NOTA
• Assicurarsi di collocare la Soundbar su una superficie piana e solida.
ITA - 29
11 AGGIORNAMENTO
DEL SOFTWARE
In futuro Samsung potrebbe fornire aggiornamenti del firmware del sistema della
Soundbar.
Porta USB
USB (5V 0.5A)
DC 24V
HDMI
DIGITAL AUDIO IN (OPTICAL)
USB (5V 0.5A)
Se viene messo a disposizione un aggiornamento,
è possibile aggiornare il firmware collegando un dispositivo USB, su cui è stato preventivamente salvato l’aggiornamento del firmware, alla porta
USB della Soundbar. Per ulteriori informazioni su come scaricare i file di aggiornamento, visitare il sito Web Samsung all’indirizzo
(www.samsung.com
Support).
Selezionare quindi il tipo di prodotto o fornire il numero di modello della Soundbar, selezionare l’opzione Software & Apps, quindi Downloads.
Tenere presente che i nomi delle opzioni possono variare.
Procedura per l’aggiornamento
Importante:
la funzione di aggiornamento rimuove tutte le impostazioni dell’utente. Si raccomanda di prendere nota delle proprie impostazioni in modo da poterle reimpostare con facilità dopo l’aggiornamento. tenendo presente che l’aggiornamento del firmware ripristina anche il collegamento al subwoofer.
1.
Connettere la chiavetta USB alla porta USB del computer.
Importante:
assicurarsi che la chiavetta USB non contenga file musicali. In caso contrario l’aggiornamento del firmwall potrebbe non riuscire.
2.
Visitare il sito Samsung su (samsung.com)
selezionare Enter Model Number, quindi fornire il modello della Soundbar.
Selezionare la sezione relativa a manuali e download, quindi scaricare il file di software più recente.
3.
Salvare il software scaricato su un archivio
USB e selezionare “Estrai qui” per decomprimere la cartella.
4.
Spegnere la Soundbar e connettere la chiavetta USB contenente l’aggiornamento software alla porta USB.
5.
Accendere la Soundbar. Entro 3 minuti, comparirà la scritta “
UPDATE
”, e l’aggiornamento avrà inizio.
6.
Una volta completato l’aggiornamento, la
Soundbar si spegnerà. Tenere premuto il tasto
p
del telecomando per 5 secondi.
“
INIT
” comparirà sul display, quindi la
Soundbar si spegnerà. L’aggiornamento è completato.
• Il prodotto ha una funzione DUAL BOOT.
Se il firmware non riesce a completare l’aggiornamento, sarà possibile aggiornare nuovamente il firmware.
7.
Ripristinare le impostazioni della Soundbar.
ITA - 30
Se non compare la scritta
UPDATE
1.
Spegnere la Soundbar, scollegare e ricollegare il dispositivo di archiviazione che contiene i file di aggiornamento alla porta
USB della Soundbar.
2.
Scollegare il cavo di alimentazione della
Soundbar, ricollegarlo, quindi accendere la
Soundbar.
NOTE
• L’aggiornamento del firmware potrebbe non funzionare correttamente se sul dispositivo di archiviazione sono presenti file audio supportati dalla Soundbar.
• Non scollegare l’alimentazione o rimuovere il dispositivo USB durante l’applicazione degli aggiornamenti. L’unità principale si spegnerà automaticamente dopo il completamento dell’aggiornamento del firmware.
• Una volta completato l’aggiornamento, la configurazione dell’utente nella Soundbar viene avviata ed è possibile ripristinare le proprie impostazioni. Consigliamo di prendere nota delle impostazioni, così da poterle ripristinare al termine dell’aggiornamento.
Attenzione: l’aggiornamento del firmware azzererà anche la connessione al subwoofer.
Se la connessione al subwoofer non viene ristabilita automaticamente dopo l’aggiornamento, fare riferimento a
Se l’aggiornamento software fallisce, verificare che l’archivio USB non sia difettoso.
• Gli utenti di Mac OS dovrebbero usare
MS-DOS (FAT) come formato USB.
• L’aggiornamento tramite USB potrebbe non essere disponibile, a seconda del produttore del dispositivo di archiviazione.
ITA - 31
12 RISOLUZIONE DEI PROBLEMI
Prima di contattare l’assistenza, controllare quanto segue.
L’unità non si accende.
Il cavo di alimentazione è saldamente collegato alla presa a parete e all’alimentatore?
;
Scollegare il cavo di alimentazione e ricollegarlo alla presa a parete e all’alimentatore per assicurarsi che la connessione è sicura.
L’alimentatore è saldamente collegato all’unità principale?
;
Scollegare l’alimentatore dalla Soundbar, quindi ricollegarlo per assicurarsi che la connessione sia salda e sicura.
Una funzione non risponde quando viene premuto il tasto.
È presente elettricità statica nell’aria?
;
Scollegare la spina del cavo di alimentazione e ricollegarla.
Si verificano interruzioni dell’audio nel modo BT.
;
Consultare le sezioni relative alla
connessione Bluetooth, alle pagine 13 e
Non viene riprodotto l’audio.
La funzione Muto è attiva?
;
Premere il tasto (
Muto
) per disattivare la funzione Muto.
Il volume è impostato al minimo?
;
Regolare il volume.
Il telecomando non funziona.
Le batterie sono esaurite?
;
Sostituirle con batterie nuove.
La distanza tra il telecomando e l’unità principale della Soundbar è troppa?
;
Avvicinare il telecomando all’unità principale della Soundbar.
Il LED rosso sul subwoofer lampeggia e il subwoofer non emette alcun suono.
Il problema può verificarsi se il subwoofer non
è collegato all’unità principale della
Soundbar.
;
Provare a connettere nuovamente il
subwoofer (consultare la pagina 6).
Il subwoofer emette un ronzio e vibra notevolmente.
Provare a regolare le vibrazioni del subwoofer.
;
Far oscillare il tasto
WOOFER
sul telecomando avanti o indietro per regolare il livello di subwoofer. (su -12, oppure tra -6
~ +6).
ITA - 32
13 LICENZA 14 AVVISO DI
LICENZA OPEN
SOURCE
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
Per inviare richieste e domande sulle open source, contattare Samsung tramite e-mail
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol together, Digital Surround, and the Digital Surround logo are registered trademarks or trademarks of
DTS, Inc. in the United States and/or other countries.
© DTS, Inc. All Rights Reserved.
15 NOTA
IMPORTANTE SUL
SERVIZIO
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol together, Virtual:X, and the DTS Virtual:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc.
All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Samsung Electronics Co.,
Ltd. is under license. Other trademarks and trade names are those of their respective owners.
• Le figure e le illustrazioni del presente manuale utente sono fornite soltanto come riferimento. Possono differire rispetto all’aspetto effettivo del prodotto.
• È possibile che vengano addebitate delle spese amministrative nei seguenti casi:
(a) l’uscita del tecnico in seguito a una chiamata non rileva difetti nel prodotto (ad es. nel caso l’utente abbia omesso di leggere questo manuale utente).
(b) utente ha portato l’unità presso un centro di riparazione che non rileva difetti nel prodotto (ad es. nel caso l’utente abbia omesso di leggere questo manuale utente).
• L’importo di tali spese amministrative verrà comunicato all’utente prima di eseguire una visita a domicilio o un eventuale intervento di manutenzione.
ITA - 33
16 SPECIFICHE E GUIDA
Specifiche
Nome del modello
USB
Peso
Dimensioni (L x A x P)
Temperatura di esercizio
Umidità di esercizio
AMPLIFICA TORE
Potenza di uscita nominale
Formati di riproduzione supportati
POTENZA IN USCITA DEL DISPOSITIVO WIRELESS
Potenza max. trasmettitore BT
Potenza max. trasmettitore SRD
HW-Q60T
5V/0,5A
3,4 kg
980,0 x 58,0 x 105,0 mm
+5°C e +35°C
10 % e 75 %
30W x 6 + 10W x 2
LPCM 2ch, Dolby Audio™
(che supporta Dolby® Digital), DTS, DTS Virtual:X
6 mW a 2,402 GHz - 2,480 GHz
25 mW a 5,725 GHz – 5,825 GHz
Nome del subwoofer
Peso
Dimensioni (L x A x P)
AMPLIFICA TORE
Potenza di uscita nominale
POTENZA IN USCITA DEL DISPOSITIVO WIRELESS
Potenza max. trasmettitore SRD
PS-WR65BB
6,2 kg
205,0 x 353,0 x 303,2 mm
160W
25 mW a 5,725 GHz – 5,825 GHz
Consumo energetico complessivo in standby (W)
Bluetooth
Metodo di disattivazione porta
2,0W
Tenere premuto il tasto
SOUND MODE
per più di
5 secondi per disattivare la funzione Bluetooth
Power.
NOTE
• Samsung Electronics Co., Ltd si riserva il diritto di modificare le specifiche senza preavviso.
• Peso e dimensioni sono approssimativi.
ITA - 34
• Samsung dichiara che questa apparecchiatura è conforme alla Direttiva
2014/53/UE.
Il testo completo della Dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: http://www.samsung.com > Supporto > Chiedi Supporto >
Inserire il nome del modello. Questa apparecchiatura può essere utilizzata in tutte le nazioni dell’UE.
[Corretto smaltimento delle batterie del prodotto]
(Applicabile nei Paesi con sistemi di raccolta differenziata)
Il simbolo riportato sulla batteria o sulla sua documentazione o confezione indica che le batterie di questo prodotto non devono essere smaltite con altri rifiuti al termine del ciclo di vita. Dove raffigurati, i simboli chimici Hg, Cd o Pb indicano che la batteria contiene mercurio, cadmio o piombo in quantità superiori ai livelli di riferimento della direttiva CE 2006/66.
Se le batterie non vengono smaltite correttamente, queste sostanze possono causare danni alla salute umana o all’ambiente.
Per proteggere le risorse naturali e favorire il riutilizzo dei materiali, separare le batterie dagli altri tipi di rifiuti e utilizzare il sistema di conferimento gratuito previsto nella propria area di residenza.
Corretto smaltimento del prodotto
(rifiuti elettrici ed elettronici)
(Applicabile nei Paesi con sistemi di raccolta differenziata)
Il simbolo riportato sul prodotto, sugli accessori o sulla documentazione indica che il prodotto e i relativi accessori elettronici (quali caricabatterie, cuffia e cavo USB) non devono essere smaltiti con altri rifiuti al termine del ciclo di vita. Per evitare eventuali danni all’ambiente o alla salute causati dallo smaltimento dei rifiuti non corretto, si invita l’utente a separare il prodotto e i suddetti accessori da altri tipi di rifiuti, conferendoli ai soggetti autorizzati secondo le normative locali.
Gli utenti domestici, in alternativa alla gestione autonoma di cui sopra, potranno consegnare l’apparecchiatura che si desidera smaltire al rivenditore, al momento dell’acquisto di una nuova apparecchiatura di tipo equivalente. Presso i rivenditori di prodotti elettronici con superficie di vendita di almeno 400 m2 è inoltre possibile consegnare gratuitamente, senza obbligo di acquisto, i prodotti elettronici da smaltire con dimensioni inferiori a 25 cm.
Gli utenti professionali (imprese e professionisti) sono invitati a contattare il proprio fornitore e verificare i termini e le condizioni del contratto di acquisto. Questo prodotto e i relativi accessori elettronici non devono essere smaltiti unitamente ad altri rifiuti commerciali.
Per informazioni sugli impegni ambientali assunti da Samsung e gli obblighi normativi specifici del prodotto, ad es. REACH, WEEE, batterie, visitare la pagina http://www.samsung.com/it/aboutsamsung/sustainability/environment/our-commitment/data/
REGOLAMENTO (UE) 2019/1782 DELLA COMMISSIONE
Specifiche per la progettazione ecocompatibile degli alimentatori esterni : www.samsung.com/global/ecodesign_component
ITA - 35
© 2020 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Centre.
UK
Area
`
Europe
Contact Centre
0333 000 0333
Web Site
IRELAND (EIRE) 0818 717100
GERMANY
FRANCE
ITALIA
SPAIN
PORTUGAL
LUXEMBURG
NORWAY
DENMARK
FINLAND
SWEDEN
91 175 00 15
808 207 267
261 03 710
NETHERLANDS 088 90 90 100
BELGIUM
POLAND
HUNGARY
AUSTRIA
06196 77 555 77
01 48 63 00 00
800-SAMSUNG (800.7267864)
02-201-24-18
21629099
707 019 70
030-6227 515
0771 726 786
801-172-678* lub +48 22 607-93-33*
Specjalistyczna infolinia do obsługi zapytań dotyczących telefonów komórkowych: 801-672-678*
* (opłata według taryfy operatora)
0680SAMSUNG (0680-726-7864)
0800 72 67 864 (0800-SAMSUNG)
SWITZERLAND 0800 726 786 www.samsung.com/uk/ support www.samsung.com/ie/ support www.samsung.com/de/ support www.samsung.com/fr/ support www.samsung.com/it/ support www.samsung.com/es/ support www.samsung.com/pt/ support www.samsung.com/be_ fr/support www.samsung.com/nl/ support www.samsung.com/be/ support (Dutch) www.samsung.com/ be_fr/support (French) www.samsung.com/no/ support www.samsung.com/dk/ support www.samsung.com/fi / support www.samsung.com/se/ support http://www.samsung.com/ pl/support/ www.samsung.com/hu/ support www.samsung.com/at/ support www.samsung.com/ch/ support (German) www.samsung.com/ ch_fr/support (French)
Area Contact Centre
Web Site
CZECH
SLOVAKIA
CROATIA
BOSNIA
NORTH
MACEDONIA
MONTENEGRO 020 405 888
SLOVENIA
SERBIA
KOSOVO
ALBANIA
BULGARIA
ROMANIA
CYPRUS
GREECE
LITHUANIA
LATVIA
ESTONIA
800 - SAMSUNG (800-726786)
0800 - SAMSUNG (0800-726 786)
072 726 786
055 233 999
023 207 777
080 697 267 (brezplačna številka)
011 321 6899
0800 10 10 1
045 620 202
8-800-77777
8000-7267
800-7267 www.samsung.com/cz/ support www.samsung.com/sk/ support www.samsung.com/hr/ support www.samsung.com/ support www.samsung.com/mk/ support www.samsung.com/ support www.samsung.com/si/ support www.samsung.com/rs/ support www.samsung.com/ support www.samsung.com/al/ support
*3000 Цена на един градски разговор
0800 111 31 Безплатен за всички оператори
*8000 (apel in retea)
08008-726-78-64 (08008-SAMSUNG)
Apel GRATUIT
Atenţie: Dacă efectuaţi apelul din reţeaua Digi (RCS/RDS), vă rugăm să ne contactaţi formând numărul
Telverde fără ultimele două cifre, astfel: 0800872678.
8009 4000 only from landline, toll free
80111-SAMSUNG (80111 726 7864) only from land line
(+30) 210 6897691 from mobile and land line www.samsung.com/bg/ support www.samsung.com/ro/ support www.samsung.com/gr/ support www.samsung.com/lt/ support www.samsung.com/lv/ support www.samsung.com/ee/ support
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 5.1ch sound
- Virtual DTS:X
- Acoustic Beam Technology
- Samsung Q-Symphony
- Bluetooth Multi Connect
Related manuals
advertisement
Table of contents
- 6 Inserting Batteries before using the Remote Control (AA batteries X 2)
- 7 Front Panel / Top Panel of the Soundbar
- 8 Bottom Panel of the Soundbar
- 9 Connecting Electrical Power
- 10 Connecting the Soundbar to the Subwoofer
- 10 Automatic connection between the Subwoofer and the Soundbar
- 11 Manually connecting the Subwoofer if automatic connection fails
- 12 Connecting an SWA-8500S (Sold Separately) to your Soundbar
- 14 Method 1. Connecting with a Cable
- 14 Connecting a TV using an HDMI Cable
- 15 Connecting using an Optical Cable
- 17 Method 2. Connecting Wirelessly
- 17 Connecting a TV via Bluetooth
- 19 Connecting using an HDMI Cable
- 20 Connecting using an Optical Cable
- 22 Connecting via Bluetooth
- 26 How to Use the Remote Control
- 29 Adjusting the Soundbar volume with a TV remote control
- 30 Using the Hidden Buttons (Buttons with more than one function)
- 30 Output specifications for the different sound effect modes
- 31 Installation Precautions
- 31 Wallmount Components
- 34 Update Procedure
- 35 If UPDATE is not displayed
- 38 Specifications
- 44 Einlegen der Batterien vor der Verwendung der Fernbedienung (AA-Batterien X 2)
- 45 Bedienfeld auf der Vorder-/Oberseite der Soundbar
- 46 Unterseite der Soundbar
- 47 Stromanschluss
- 48 Verbinden der Soundbar mit dem Subwoofer
- 48 Automatische Verbindung zwischen Subwoofer und Soundbar
- 49 Manuelles Verbinden des Subwoofers bei Fehlschlagen der automatischen Verbindung
- 50 Verbinden des SWA-8500S (separat erhältlich) mit einer Soundbar
- 52 Methode 1. Verbindung mit einem Kabel
- 52 Einen Fernseher über ein HDMI-Kabel verbinden
- 53 Verbindung mit einem optischen Kabel
- 55 Methode 2. Drahtlose Verbindung
- 55 Verbindung eines Fernsehers per Bluetooth
- 57 Über ein HDMI-Kabel verbinden
- 58 Verbindung mit einem optischen Kabel
- 60 Anschließen per Bluetooth
- 64 So verwenden Sie die Fernbedienung
- 67 Anpassen der Soundbar-Lautstärke mit einer TV-Fernbedienung
- 68 Verwenden der verborgenen Tasten (Tasten mit mehr als einer funktion)
- 68 Ausgabe-spezifikationen für die unterschiedlichen sound-effekt-modi
- 69 Vorsichtsmaßnahmen für die Installation
- 69 Komponenten für die Anbringung an der Wand
- 72 Updateverfahren
- 73 Wenn UPDATE nicht angezeigt wird
- 76 Technische daten
- 82 Insertion des piles avant l’utilisation de la télécommande (Piles AA X 2)
- 83 Panneau frontal/supérieur de la Soundbar
- 84 Panneau inférieur de la Soundbar
- 85 Connexion de l’alimentation électrique
- 86 Connexion de la Soundbar au Caisson de basse
- 86 Connexion automatique entre le Caisson de basse et la Soundbar
- 87 Connexion manuelle du Caisson de basse si la connexion automatique échoue
- 88 Connexion du SWA-8500S (Vendue séparément) à une Soundbar
- 90 Méthode 1. Connexion avec un câble
- 90 Connexion d’un téléviseur à l’aide d’un câble HDMI
- 91 Connexion à l’aide d’un câble optique
- 93 Méthode 2. Connexion sans fil
- 93 Connexion à un téléviseur via Bluetooth
- 95 Connexion à l’aide d’un câble HDMI
- 96 Connexion à l’aide d’un câble optique
- 98 Connexion via Bluetooth
- 102 Comment utiliser la télécommande
- 105 Réglage du volume de la Soundbar avec une télécommande de téléviseur
- 106 Utilisation des touches dissimulées (Touches avec plus d’une fonction)
- 106 Spécifications de sortie pour les différents modes d’effets sonores
- 107 Précautions d’installation
- 107 Composants de fixation au mur
- 110 Procédure de mise à jour
- 111 Si UPDATE ne s’affiche pas
- 114 Spécifications
- 120 Inserimento delle batterie prima dell’utilizzo del telecomando (2 batterie AA)
- 121 Pannello anteriore / Pannello superiore della Soundbar
- 122 Pannello inferiore della Soundbar
- 123 Collegamento alla rete elettrica
- 124 Connessione della Soundbar al Subwoofer
- 124 Connessione automatica tra il subwoofer e la Soundbar
- 125 Connessione manuale del subwoofer in caso di connessione automatica non riuscita
- 126 Collegamento del kit SWA-8500S (venduto separatamente) alla Soundbar
- 128 Metodo 1. Collegamento mediante un cavo
- 128 Collegamento di una TV tramite un cavo HDMI
- 129 Collegamento tramite un cavo ottico
- 131 Metodo 2. Connessione wireless
- 131 Connessione di una TV mediante Bluetooth
- 133 Collegamento tramite un cavo HDMI
- 134 Collegamento tramite un cavo ottico
- 136 Connessione tramite Bluetooth
- 140 Come utilizzare il telecomando
- 143 Regolazione del volume della Soundbar tramite il telecomando di una TV
- 144 Utilizzo dei pulsanti nascosti (pulsanti con più di una funzione)
- 144 Specifiche di uscita per diverse modalità di effetti sonori
- 145 Precauzioni per l’installazione
- 145 Componenti per il montaggio a parete
- 148 Procedura per l’aggiornamento
- 149 Se non compare la scritta UPDATE
- 152 Specifiche