OPERATOR`S MANUAL - Industrial Cleaning Equipment

OPERATOR`S MANUAL - Industrial Cleaning Equipment
VHP
OPERATOR’S MANUAL
■ vhp2-1500 (1.109-556.0)
■ vhp3-2000 (1.109-557.0)
Ti
Gd
NIN zzar
AR r Ha
W pove
use vapor fuel only
89139490-1
LIS T E D
®
For technical assistance or the Landa Dealer nearest you,
consult our web page at www.landa.com
8.913-949.0
CONTENTS
Introduction & Important Safety Information...................................... 3-5
Component Identification...................................................................... 6
Installation......................................................................................... 7-8
Pre-Operation Checklist....................................................................... 8
Instructions for Lighting........................................................................ 9
Assembly Instructions......................................................................... 10
Operating Instructions........................................................................ 11
Detergents and General Cleaning Techniques................................... 12
Shutting Down and Clean up.............................................................. 13
Storage............................................................................................... 13
Troubleshooting............................................................................. 14-15
Maintenance and Service.............................................................. 16-17
Oil Change Record............................................................................. 17
Exploded View.............................................................................. 18-19
Exploded View Parts List............................................................... 20-22
Hose & Spray Gun Assembly............................................................. 23
Pump Exploded View and Parts List.............................................. 24-25
VRT 3 Unloader Exploded Views and Parts List................................ 26
Injector Assemblies............................................................................ 27
Warranty............................................................................................. 28
Spanish.......................................................................................... 29-37
Model Number ______________________________
Serial Number ______________________________
Date of Purchase ____________________________
The model and serial numbers will be found on a decal attached
to the pressure washer. You should record both serial number and
date of purchase and keep in a safe place for future reference.
2
LANDA VHP • 8.913-949.0 • Rev. 5/13
Thank you for purchasing this Pressure Washer.
We reserve the right to make changes at any time
without incurring any obligation.
Owner/User Responsibility:
The owner and/or user must have an understanding of
the manufacturer’s operating instructions and warnings
before using this pressure washer. Warning information
should be emphasized and understood. If the operator
is not fluent in English, the manufacturer’s instructions
and warnings shall be read to and discussed with
the operator in the operator’s native language by the
purchaser/owner, making sure that the operator comprehends its contents.
DANGER: Improper connection of the equipmentgrounding conductor can result in a risk of electrocution. Check with a qualified electrician or
service personnel if you are in doubt as to whether
the outlet is properly grounded. Do not modify the
plug provided with the product - if it will not fit the
outlet, have a proper outlet installed by a qualified
electrician. Do not use any type of adaptor with
this product.
WARNING: Keep wand, hose, and
water spray away from electric
wiring or fatal electric shock may
result.
6. To protect the operator from
electrical shock, the machine keep water
must be electrically grounded.
spray away from
It
is the responsibility of the electrical wiring.
owner to connect this machine
to a UL grounded receptacle of proper voltage and
amperage ratings. Do not spray water on or near
electrical components. Do not touch machine with
wet hands or while standing in water. Always disconnect power before servicing.
WARNING
Owner and/or user must study and maintain for future
reference the manufacturers’ instructions.
The operator must know how to stop the machine
quickly and understand the operation of all controls.
Never permit anyone to operate the engine without
proper instructions.
SAVE THESE INSTRUCTIONS
This manual should be considered a permanent
part of the machine and should remain with it if
machine is resold.
When ordering parts, please specify model and
serial number. Use only identical replacement parts.
This machine is to be used only by trained operators.
Important Safety
Information
WARNING: To reduce the risk of
injury, read operating instructions carefully before using.
1. Read the owner's manual
thoroughly. Failure to follow
instructions could cause malfunction of the machine and
read operator’s
manual thoroughly
result in death, serious bodily
prior to use.
injury and/or property damage.
2. Know how to stop the machine and bleed pressure
quickly. Be thoroughly familiar with the controls.
3. Stay alert — watch what you are doing.
4. Do not replace LP tank while machine is running.
5. All installations must comply with local codes. Contact your electrician, plumber, utility company or the
selling distributor for specific details. If your machine
is rated 250 volts or less, single phase will be provided with a ground fault circuit interrupter (GFCI).
If rated more than 250 volts, or more than single
phase this product should only be connected to a
power supply receptacle protected by a GFCI.
PRESSURE WASHER OPERATOR’S MANUAL
INTRODUCTION & Important Safety Information
WARNING WARNING: Flammable liquids
can create fumes which can ignite, causing property damage
or severe injury.
WARNING: Risk of explosion —
Operate only where open flame
risk of explosion:
or torch is permitted.
If gas smell
present turn off
supply
WARNING
WARNING: Risk of fire — Do not
change tanks when the product
is operating or still hot.
WARNING: Use vapor fuel only.
7. Oil burning appliances shall
be installed only in locations
risk of fire.
do not add fuel
where combustible dusts and
when operating
flammable gases or vapors
machine.
are not present. Do not store
or use gasoline near this machine.
8. Keep operating area clear of all persons.
WARNING
use protective
eye wear
and clothing
when operating
this equipment.
LANDA VHP • 8.913-949.0 • Rev. 5/13
WARNING: High pressure spray
can cause paint chips or other
particles to become airborne
and fly at high speeds. To avoid
personal injury, eye, hand and
foot safety devices must be
worn.
9. Eye, hand, and foot protection
must be worn when using this
equipment.
3
OPERATOR’S MANUAL
PRESSURE WASHER
Important Safety Information
WARNING
WARNING:This machine exceeds
85 db appropriate ear protection
must be worn.
ear protection
must be worn
CAUTION: Hot discharge fluid.
Do not touch or direct discharge
stream at persons.
HOT discharge fluid: do NOT TOUCH OR
DIRECT DISCHARGE
STREAM AT PERSONS.
WARNING
Risk Of Injury.
Hot Surfaces
Can Cause Burns
WARNING: This machine produces hot water and must have
insulated components attached
to protect the operator.
WARNING: Risk of injury. Hot
surfaces can cause burns. Use
only designated gripping areas
of spray gun and wand. Do not
place hands or feet on non-insulated areas of the pressure
washer.
10.To reduce the risk of injury, close supervision is
necessary when a machine is used near children.
Do not allow children to operate the pressure
washer. This machine must be attended during
operation.
WARNING
Trigger Gun Kicks
back - Hold with
both hands
WARNING
risk of injection
or severe injury
To persons. keep
clear of nozzle.
WARNING: Grip cleaning wand
securely with both hands before
starting. Failure to do this could
result in injury from a whipping
wand.
11.Never make adjustments on
machine while in operation.
12. Be certain all quick coupler fittings are secured before using
pressure washer.
WARNING: High pressure developed by these machines will
cause personal injury or equipment damage. Keep clear of
nozzle. Use caution when operating. Do not direct discharge
stream at people, or severe injury or death will result.
WARNING: Protect machine from
WARNING
freezing.
13. To keep machine in best
operating conditions, it is
important you protect machine
from freezing. Failure to protect
machine from freezing
Protect from
freezing
could cause malfunction of the
machine and result in death,
serious bodily injury, and/or property damage. Follow storage instructions specified in this manual.
14. Inlet water must be clean fresh water and no hotter
then 90°F.
WARNING WARNING: Risk of asphyxiation.
Use this product only in a well
ventilated area.
15. Avoid installing machines in
small areas or near exhaust
fans. Adequate oxygen is
risk of
needed for combustion or
asphyxiation. use
this product only
dangerous carbon monoxide
in a well
will result.
ventilated area.
16.Manufacturer will not be liable for any changes
made to our standard machines or any components
not purchased from us.
17. The best insurance against an accident is precaution and knowledge of the machine.
WARNING: Be extremely careful
when using a ladder, scaffolding
or any other relatively unstable
location. The cleaning area
should have adequate slopes
and drainage to reduce the possibility of a fall due to slippery
RISK OF INJURY
FROM FALLS WHEN
surfaces.
USING LADDER.
18.Do not overreach or stand on unstable support.
Keep good footing and balance at all times.
19. Do not operate this machine when fatigued or under
the influence of alcohol, prescription medications,
or drugs.
20.Follow the maintenance instructions specified in
the manual.
21. Do not replace LP tank while machine is running.
Serious injury could result.
WARNING: Use vapor fuel only.
22. The LP models are designed to run on vapor propane fuel. Do not use liquid fuel. Have a qualified
serviceman install and service your equipment.
WARNING
4
LANDA VHP • 8.913-949.0 • Rev. 5/13
23.Never expose a spark or flame where there may
be unburned gas present.
24. Install the machine 18” above the floor and about
2 feet from wall providing adequate ventilation and
space.
25.When making repairs disconnect from electrical
source and shut off gas valve.
26. Install this machine on non combustible flooring.
27. Do not allow acids, caustic or abrasive fluids to pass
through the pump.
28.Never run pump dry or leave spray gun closed
longer than 1-2 minutes.
WARNING: If connection is made to portable water
supply, a back flow device must be provided.
PRESSURE WASHER OPERATOR’S MANUAL
Important Safety Information
Follow the maintenance instructions specified in the manual.
Example Of Down
Draft Diverter
For Gas Fired
Machines
5
LANDA VHP • 8.913-949.0 • Rev. 5/13
PRESSURE WASHER
Component Identification
Discharge
Nipple
High Limit
Snap Switch
OPERATOR’S MANUAL
Detergent
Injector
High Pressure
Hose Hanger
Quick
Coupler
Rupture
Disk
Collar
Wand
Holder
Reversed View
Pump &
Burner Switch
Water Supply
(not included)
Wand
Rest
Propane
Hose
Brass Soap
Nozzle
LP Tank
(not
included)
GFCI
LP Shelf
Trigger
Nozzle
Quick
Coupler
Variable
Pressure
Wand
Variable Pressure
Control Handle
89139490-2
Spray Gun
6
LANDA VHP • 8.913-949.0 • Rev. 5/13
High
Pressure
Hose
WARNING: Moving this machine on an incline may
cause instability and could result in the machine
tipping over. Equipment damage or bodily harm
could occur.
Place machine in a convenient location providing ample
support, drainage and room for maintenance.
These machines are intended for indoor use. Machine must be stored indoors when not in use.
setting. Follow the installation and adjustment instructions provided with your replacement valve.
Note: Air for combustion and ventilation along with
exhaust flue sizing must conform to methods outlined
in current American Standard (ANSI-Z223.1) National
Fuel Gas Code or National Standard of Canada CSA149.1 and CSA-149.2 “Installation Code for Gas Burning Appliances”.
Electrical:
Location:
The location should protect the machine from damaging environmental conditions, such as wind, rain and
freezing.
1.The machine should be run on a level surface
where it is not readily influenced by outside sources
such as strong winds, freezing temperatures, rain,
etc. Consider accessibility for the replacing of LP
tanks, refilling of detergents, adjustments and
maintenance when selecting a location. Normal
precautions should be taken by the operator to
prevent excess moisture from reaching electrical
components.
2.It is recommended that a partition be made between the wash area and the machine to prevent
direct spray from the spray gun to come in contact
with machine. Excess moisture reaching the electrical controls will reduce the machine life and may
cause electrical shorts.
3.During installation, beware of poorly ventilated
locations or areas where exhaust fans may cause
an insufficient supply of oxygen. Sufficient combustion can only be obtained when there is a sufficient
supply of oxygen available for the amount of fuel
being burned. If it is necessary to install in a poorly
ventilated area, outside fresh air may have to be
piped to the burner and a fan installed to bring air
into the room. Avoid small locations or areas near
exhaust fans.
This machine, when installed, must be electrically
grounded in accordance to local codes. Check for
proper power supply using a volt meter. The VHP215021D requires a 20 amp receptacle to comply with
UL 1776 certification standards.
Venting:
PRESSURE WASHER OPERATOR’S MANUAL
Installation
Regulations or ventilation concerns may call for a
chimney or furnace pipe.
When venting, if the machine is to be in an enclosed
area with a chimney on it, be sure the chimney is the
same size as the stack on the machine. Poor draft
will cause machine to soot and not operate efficiently.
When placing for installation, keep in mind that the
pressure washer should be positioned in such a manner that the stack will be as straight as possible and
protrude through the roof of the building at a proper
location and at sufficient height to eliminate downdraft.
The chimney of gas fired machines should be installed
with a down draft diverter.
Draft Diverter:
A draft diverter should be installed above the heating
coil. The diverter serves to sever the chimney effect
created in all sections of furnace pipe positioned below
to enhance the draft through the burner. It also helps
prevent freezing of the coil due to wind chill factors.
NOTE: the draft diverter is not standard on VHP machines.
Gas Codes:
Confer with local gas company and with proper municipal officials regarding any specific code or regulations governing the installation. The installation must
conform to local codes.
The gas pressure coming out of the regulator and going
to the burner ring has been factory set for elevations of
0 to 2000 ft. Altitudes greater than 2000 ft will require
adjustments to the gas manifold pressures. Consult
your local service dealer/distributor for high altitude
adjustments. In Canada, certification for installation
at altitudes over 4500 feet above sea level is the jurisdiction of local authorities. You should not readjust the
burner ring gas pressure. If you replace your gas valve,
you will need to adjust the new valve. Refer to your
machine’s specification plate for the correct pressure
When the pressure washer is installed in a tightly closed
room without ventilation openings to the outdoors or
other rooms, provisions shall be made for supplying
air for combustion through special openings, one near
the floor line and the other near the ceiling, each to be
sized on the basis of one square inch or more of free
area for each 1,000 BTU input per hour.
LANDA VHP • 8.913-949.0 • Rev. 5/13
7
PRESSURE WASHER
OPERATOR’S MANUAL
Installation
Placement:
Shut-Off Valve:
Do not locate near any combustible material. Keep all A gas shut-off valve has been installed between the gas
flammable material at least 20 feet away.
supply line and the washer. The plumbing also includes
Allow enough space for servicing the machine.
a union between the shut-off valve and the burner.
Local code will require certain distances from floor and
Condensation from Coils:
walls. (Two feet away should be adequate.)
When cold water is being pumped into the water heater
Water Source:
coils, and the burners are on, condensation will form on
Water source for machine should be supplied by a 5/8" the coils and drip down into the burner compartment
I.D. garden hose with a city water pressure of not less giving the appearance of a leaking coil, particularly on
than 30 psi. If the water supply is inadequate, or if the cold humid days.
garden hose is kinked, the machine will run very rough
Check Water Heater Coil for Leaks:
and the burner will not fire.
With the burner “OFF” start the pumping machine and
Connection:
allow to run for a few minutes. Look into the burner
Connect the wand, nozzle, hose and spray gun (where compartment with a drop light or flashlight. If no leak
applicable). On pipe thread connections, use teflon is visible, then subsequent water dripping from the coil
tape to avoid water leaks. (See Component Identifica- will be from condensation in the flue gases when the
burner is on, as described in the previous paragraph.
tion.)
Attach high pressure hose to discharge nipple by pulling the quick coupler collar back and inserting it onto
the discharge nipple. Then push the collar forward to
secure. A detergent injector could be inserted between
the hose coupler and the discharge nipple. (See page
10.)
Place detergent dip tube into liquid soap or detergent
solution. Avoid letting tube suck air.
Caution: When installing propane hose to LP tank,
please note that it has left hand threads.
Inspection and Testing:
Before turning gas under pressure into piping, all openings from which gas can escape should be closed.
Immediately after turning on gas, the system should
be checked for leaks. This can be done by watching the
1/2 cubic foot test dial and allowing 5 minutes to show
any movement, or by soaping each pipe connection
and watching for bubbles. If a leak is found, make the
necessary repairs and repeat the above test.
Defective pipes or fittings should be replaced and not
repaired. Never use a flame or fire in any form to locate
gas leaks, use a soap solution.
After the piping and meter have been checked completely, purge the system of air. DO NOT bleed the air
inside an enclosed room.
The pressure washer and its individual shut-off valve
must be disconnected from the gas supply piping
system during the pressure testing of that system at
test pressure in excess of 1/2 psig or damage to the
gas valve will occur.
8
Pre-Start Check List
Is machine protected from downdraft and excessive wind?
Is machine shielded from moisture
or water spray?
Is the voltage correct and circuit
breaker and supply cord adequate
according to specifications and
serial plate notation?
Is the machine electrically
grounded?
Is there ample water supply?
Have all flammable liquids or gases
been removed from installation
location?
Is the machine properly vented to
allow adequate air flow?
Is there an adequate gas supply for
the BTU rating of the burner?
Have gas lines been checked for
gas leaks?
Have all operators using this
machine been instructed properly
& have they read the manual?
Has the machine been installed
according to the instructions in the
operator's manual?
Is the incoming gas supply pressure
to the machine between 6-14 water
column inches or 1/2 psig?
LANDA VHP • 8.913-949.0 • Rev. 5/13
YES
NO
WARNING: If “NO” has been checked on any of the
above questions, do not operate.
WARNING
risk of fire or
explosion:
follow
instructions
exactly.
WARNING: If you do not follow
instructions exactly, a fire or
explosion may result causing
property damage, personal injury or loss of life.
1. This machine has a pilot
which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
2.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor
because propane gas is heavier than air and will
settle on the floor.
For your safety:
“What to do if you smell gas”
a. Do not try to light any appliance.
b. Do not touch any electrical switch; do not
use any phone in your building.
c. Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
PRESSURE WASHER OPERATOR’S MANUAL
instructions for lighting
d. If you cannot reach your gas supplier, call
the fire department.
3. Use only your hand to push in or turn gas control
knob. Never use tools. If the knob will not push in
or turn by hand, don’t try to repair it, call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
4.Do not use this machine if any part has been
under water. Immediately call a qualified service
technician to inspect the machine and to replace
any part of the control system or any gas control
that has been under water.
9
LANDA VHP • 8.913-949.0 • Rev. 5/13
PRESSURE WASHER
OPERATOR’S MANUAL
Assembly Instructions
Detergent
Injector
Spray
Gun
High
Pressure
Hose
Detergent
Suction
Tube
STEP 1: Connect power cord to
proper electrical outlet according
to serial plate information. Push
in GFCI reset button. The VHP215021D requires a 20 amp receptacle.
Safety
Latch
Discharge
Nipple
STEP 2: Connect high pressure
hose to discharge nipple by sliding quick coupler collar back. (If
detergent is to be applied, insert
a detergent injector.) Insert quick
coupler onto discharge nipple and
secure by pushing quick coupler
collar forward.
High
Pressure
Hose
STEP 3: Attach the high pressure
hose to the spray gun using teflon
tape on hose threads. Move safety
latch into locked position.
Propane
Hose
STEP 4: Check oil level by using
supplied dip-stick. Use SAE 30W
non-detergent only.
STEP 5: Connect propane hose to
a propane tank.
Operating Instructions
Turn Pump/
Burner
Switch Off
10
STEP 1: STOP! Read operator’s manual
before operating this machine. Failure to
read operation and warning instructions may
result in personal injury or property damage.
Connect water supply hose to inlet connector and turn water on.
89139490-5
STEP 2: Turn all switches off. Remove and
position LP tank as far from machine as supply
hose will allow.
LANDA VHP • 8.913-949.0 • Rev. 5/13
PRESSURE WASHER
Operating Instructions
Coupler
Collar
STEP 4: Pull the spring-loaded
collar of the wand coupler collar back to insert your choice
of pressure nozzle. Caution:
Never replace nozzles without
Grip spray gun variable pressure wand engaging the safety latch on
securely. Then turn the variable pressure the spray gun trigger.
control handle counterclockwise to flush
any debris out of soap nozzle.
STEP 5: Release the coupler
collar and push the nozzle until
the collar clicks. Pull the nozzle to
make sure it is seated properly.
OPERATOR’S MANUAL
STEP 3: Before installing nozzle, Pull
trigger on spray gun allowing water to flow
until all air has been discharged from the
system. Check for water leaks and tighten
as needed.
Brass Soap
Variable Pressure
Nozzle
Wand (VP)
High
Pressure
Nozzle
Variable Pressure
Control Handle
Control
Knob
Trigger
STEP 6: Selection of high or low pressure is accompanied by turning the handle. Note: High
pressure nozzle must be inserted at end of wand to
obtain high pressure. To apply soap read operator's
manual.
Gas
Valve
STEP 7: Open valve on LP tank, then slightly depress
main gas valve control knob on the right side of the machine and turn it counterclockwise to the Pilot position.
NOTE: Knob cannot be turned from “Pilot” to “OFF” unless
the knob is slightly depressed.
Pump and Burner
Switch
Red
Ignitor
89139490-6
STEP 9: Turn switch to pump position and
pull the trigger on the spray gun. Turn variable pressure control wand handle clockwise
to obtain pressure for cold water operation.
For hot water, turn the switch to the burner
position and pull the trigger on the spray gun.
To apply detergent, read section on Detergents and General Cleaning Techniques.
Step 8: Depress the control knob all the way and hold it in. After
five (5) seconds, depress the red ignitor until you hear a loud click.
Repeat 3 or 4 times if necessary until pilot is lit. If pilot does not
remain lit, repeat operation allowing a longer period of time before
releasing the gas valve knob. After the pilot lights, continue to hold
the control knob down for about one (1) minute before releasing.
Look at the pilot viewing mirror at the rear of the machine.
Turn gas control knob counterclockwise to “ON.”
11
LANDA VHP • 8.913-949.0 • Rev. 5/13
PRESSURE WASHER
OPERATOR’S MANUAL
detergents & general Cleaning techniques
WARNING
WARNING: Some detergents
may be harmful if inhaled or
ingested, causing severe nausea, fainting or poisoning. The
harmful elements may cause
property damage or severe
injury.
STEP 1: Use detergent designed
specifically for pressure washers.
Household detergents could damage the pump. Prepare detergent
solution as required by the manufacturer. Fill a container with pressure washer detergent. Place the
filter end of detergent suction tube
into the detergent container.
STEP 2: Apply safety latch to spray gun trigger.
Secure black detergent nozzle into quick coupler.
NOTE: Detergent cannot be applied using the yellow
nozzle.
STEP 3: With the motor
running, pull trigger to operate machine. Liquid detergent is drawn into the machine and mixed with water
at an approximate ratio of 15
to 1. Turn pressure control
handle on wand counterclockwise. This lowers the pressure by directing the water
flow through the soap nozzle and allow detergent
injector to siphon soap.
motion keeping the spray nozzle approximately 1 foot
from cleaning surface. Use overlapping strokes as you
clean and rinse any surface. For best surface cleaning
action, spray at a slight angle.
Recommendations:
• Before cleaning any surface, an inconspicuous
area should be cleaned to test spray pattern and
distance for maximum cleaning results.
• If painted surfaces are peeling or chipping,
use extreme caution as pressure washer may
remove the loose paint from the surface.
• Keep the spray nozzle a safe distance from the surface you plan to clean. High pressure wash
a small area, then check the surface for damage. If no damage is found, continue to pressure
washing.
CAUTION - Never use:
• Bleach, chlorine products and other corrosive
chemicals
• Liquids containing solvents (i.e., paint thinner,
gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the machine and will damage the surface being cleaned.
rinsing
It will take a few seconds for the detergent to clear.
Apply safety latch to spray gun. Remove black soap
nozzle from the quick coupler. Select and install the
desired high pressure nozzle. NOTE: You can also stop
detergent from flowing by simply removing detergent
siphon tube from bottle.
Apply detergent to work area. Do not allow detergent
to dry on surface.
IMPORTANT:You must flush the detergent injection
system after each use by placing the suction tube
into a bucket of clean water, then run the pressure
washer in low pressure for 1-2 minutes.
cleaning tips
12
Pre-rinse cleaning surface with fresh water. Place detergent suction tube directly into cleaning solution and
apply to surface at low pressure (for best results, limit
your work area to sections approximately 6 feet square
and always apply detergent from bottom to top). Allow
detergent to remain on surface 1-3 minutes. Do not
allow detergent to dry on surface. If surface appears
to be drying, simply wet down surface with fresh water.
If needed, use brush to remove stubborn dirt. Rinse at
high pressure from top to bottom in an even sweeping
LANDA VHP • 8.913-949.0 • Rev. 5/13
Pump Switch
89139490-7
STEP 2: After water has cooled,
turn pump off. Turn main gas valve
off, then close the valve on the LP
tank. Secure the LP tank to the
machine when moving it.
STEP 3: Turn the water off. To protect from freezing, pull the trigger
on spray gun to allow water to drain
from the system.
STEP 4: Squeeze trigger on spray
gun to relieve remaining pressure.
Move safety latch into its locked
position.
OPERATOR’S MANUAL
STEP 1: Remove detergent suction
tube from container and insert into
one (1) gallon of fresh water. Flush
detergent lines with fresh water,
switch to the pump position and
continue to spray water allowing
burner to cool.
PRESSURE WASHER
shutting down and clean-up
STORAGE
CAUTION: Always store your pressure washer in a
location where the temperature will not fall below
32°F (0°C). The pump in this machine is susceptible
to permanent damage if frozen. FREEZE DAMAGE
IS NOT COVERED BY WARRANTY.
1. Stop the pressure washer, squeeze spray gun trigger to release pressure.
2.Detach water supply hose and high pressure hose.
3. Turn on the machine for a few seconds, until remaining water exits. Turn engine off immediately.
4. Drain the gas and oil from the engine.
5.Do not allow high pressure hose to become kinked.
6. Store the machine and accessories in a room which
does not reach freezing temperatures.
CAUTION: Failure to follow the above directions will
result in damage to your pressure washer.
When the pressure washer is not being operated or is
being stored for more than one month, follow these
instructions:
1. Replenish engine oil to upper level.
2. Drain gasoline from fuel tank, fuel line, fuel valve
and carburetor.
3.Pour about one teaspoon of engine oil through
the spark plug hole, pull the starter grip several
times and replace the plug. Then pull the starter
grip slowly until you feel increased pressure which
indicates the piston is on its compression stroke and
leave it in that position. This closes both the intake
and exhaust valves to prevent rusting of cylinder.
4. Cover the pressure washer and store in a clean, dry
place that is well ventilated away from open flame
or sparks. NOTE: The use of a fuel additive, such
as STA-BIL®, or an equivalent, will minimize the
formulation of fuel deposits during shortage. Such
additives may be added to the gasoline in the fuel
tank of the engine, or to the gasoline in a storage
container.
After Extended Storage
CAUTION: Prior to restarting, thaw out any
possible ice from pressure washer hoses,
spray gun or wand.
Engine Maintenance
During the winter months, rare atmospheric conditions
may develop which will cause an icing condition in the
carburetor. If this develops, the engine may run rough,
lose power and may stall. This temporary condition can
be overcome by deflecting some of the hot air from the
engine over the carburetor area. NOTE: Refer to the
engine manufacturer's manual for service and maintenance of the engine.
LANDA VHP • 8.913-949.0 • Rev. 5/13
13
problem
possible cause
solution
pulsation
Faulty pulsation damper
Check precharge. If low, recharge or install
new one.
low
pressure
Worn nozzle
Replace with nozzle of proper size.
Belt slippage
Tighten or replace with correct belt.
Air leak in inlet plumbing
Disassemble, reseal and reassemble.
Relief valve stuck, partially plugged or
improperly adjusted. Valve seat worn
Clean and adjust relief valve; check for
worn or dirty valve seats. Kit available.
Inlet suction strainer clogged or
improperly sized
Clean. Use adequate size. Check more
frequently.
Worn packing.
Abrasives in pumped in cavitation.
Inadequate water
Install proper filter. Suction at inlet manifold must be limited to lifting less than 20
feet of water or 8.5 psi vacuum.
Fouled or dirty inlet or discharge valves
Clean inlet and discharge valve
assemblies.
Worn inlet, discharge valve blocked
or dirty
Replace worn valves, valve seats and/or
discharge hose.
Leaky discharge hose
Replace.
pump runs
extremely rough,
pressure
very low
Restricted inlet or air entering the inlet
plumbing
Proper size inlet plumbing; check for air
tight seal.
water leakage
from under
manifold.
Worn packing
Install new packing.
oil leaking in area
of crankshaft
Worn crankshaft seal or improperly
installed oil seal O-ring
Remove oil seal retainer and replace
damaged O-ring and/or seals.
Bad bearing
Replace bearing.
excessive
play in end of
crankshaft
pulley
Worn main bearing from excessive
tension on drive belt
Replace crankcase bearing and/or
tension drive belt.
water in
crankcase
Humid air condensing into water inside Change oil intervals. Use any high grade
crankcase
automotive 30 weight non-detergent oil.
PRESSURE WASHER
Troubleshooting Guide
Troubleshooting
Worn packing and/or piston rod sleeve;
O-rings on plunger retainer worn
Worn crankcase piston rod seals
Replace packing. Replace O-rings.
oil leaking at
rear portion
of crankcase
loud knocking
Worn crankcase piston rod seals
Replace seals.
Pulley loose on crankshaft
Check key and tighten set screw.
noise in pump
Broken or worn bearing
Replace bearing.
oil leaking from
underside of
crankcase
14
Inlet restrictions and/or air leaks. Stuck Replace worn cup or cups. Clean out
inlet or discharge valve
foreign material. Replace worn valves.
Replace seals.
LANDA VHP • 8.913-949.0 • Rev. 5/13
problem
pump
noisy
possible cause
Air in suction line
solution
Check water supply and connections on
suction line.
Broken or weak inlet or discharge
valve springs
Check and replace if necessary.
Excessive matter in valves
Check and clean if necessary.
Worn bearings
Check and replace if necessary.
presence of
water in oil
Oil seal worn
Check and replace if necessary.
High humidity in air
Check and change oil twice as often.
water dripping
from under pump
Piston packing worn
Check and replace if necessary.
O-ring plunger retainer worn
Check and replace if necessary.
Pump protector
Check inlet water pressure.
Oil dripping
Oil seal worn
Check and replace if necessary.
excessive
vibration in
delivery line
Irregular functioning of the valves
Check and replace if necessary.
Relief valve
leaks water
Wrong nozzle size, debris in nozzle
Clean or replace with correct nozzle.
burner will
not light
No fuel
Open gas valve.
Pilot light is out
Light pilot.
Defective high limit switch
Replace switch.
Burner smokes
Stack restriction
See venting under installation (page 7).
pilot does
not light
Manual pilot valve closed
Open pilot valve.
Gas leak in pilot
Call qualified serviceman.
Piezo ignitor
Adjust spark gap. Secure wires.
pilot ignites but
will not stay on
when gas cock
dial is released
Pilot too far away from thermocouple
Adjust thermocouple closer to flame.
Thermocouple loose at regulator
safety valve
Tighten to firm fit.
short
thermocouple
life
Excessive heat from pilot light
Decrease pilot supply gas.
Thermocouple too close to pilot
Adjust thermocouple farther away.
burner cycling
on/off
Defective high limit switch
Replace switch.
washer will
not steam
Steam valve closed
Open valve (counterclockwise).
Burner not on
Turn burner switch to "ON" position.
Coil dirty or sooty
See coil maintenance section.
Steam valve clogged
Clean or replace.
PRESSURE WASHER Troubleshooting Guide
Troubleshooting
15
LANDA VHP • 8.913-949.0 • Rev. 5/13
PRESSURE WASHER
OPERATOR’S MANUAL
Maintenance & Service
PREVENTATIVE
MAINTENANCE
1.Check to see that the water pump is properly
lubricated.
2.Follow winterizing instructions to prevent freeze
damage to the pump and coils.
3. Always neutralize and flush detergent from system
after use.
4. If water is known to be high in mineral content, use
a water softener in your water system or de-scale
as needed.
5. Do not allow acidic, caustic or abrasive fluids to be
pumped through system.
6.Always use high grade quality Landa cleaning
products.
7.Never run pump dry for extended periods
of time.
8. Periodically delime coils as per instructions.
It is advisable, periodically, to visually inspect the
burner. Check air inlet to make sure it is not clogged
or blocked. Wipe off any oil spills and keep this equipment clean and dry.
The areas around the Landa washer should be kept
clean and free of combustible materials, gasoline and
other flammable vapors and liquids.
The flow of combustion and ventilating air to the burner
must not be blocked or obstructed in any manner.
MAINTENANCE AND SERVICE
Unloader Valves:
Unloader valves relieve pressure in the line when
the shut-off spray gun is closed. Unloader valves are
preset and tested at the factory before shipping. Occasional adjustment of the unloader may be necessary to maintain correct pressure. (Contact your local
dealer for correct procedure in adjusting unloader
valve.) Tampering with the factory setting may cause
personal injury and/or property damage, and will void
the manufacturer's warranty.
Winterizing Procedure:
Damage due to freezing is not covered by warranty.
Adhere to the following cold weather procedures whenever the washer must be stored or operated outdoors
under freezing conditions.
During winter months, when temperatures drop below
32°F, protecting your machine against freezing is necessary. Store the machine in a heated room. If this is not
possible then mix a 50/50 solution of anti-freeze/water
into a 5 gallon bucket and with a short section of garden
hose elevate the bucket and turn the pump on to siphon
the anti-freeze through the machine. If compressed air
is available, an air fitting can be screwed into the inlet
connector and, by injecting compressed air, all water
will be blown out of the system.
High Limit Hot Water Thermostat:
For safety, each machine is equipped with a high limit
control switch. In the event the temperature of the water
should exceed its operating temperature, the high limit
control will turn the burner off until the water cools.
Pumps:
Use only SAE 30 weight non-detergent oil. Change oil
after first 50 hours of use. Thereafter, change oil every
three months or at 500 hour intervals. Oil level should
be checked through use of the dipstick found on the
top of the pump or by the red dot visible through the oil
gauge window. Oil should be maintained at that level.
Cleaning of Coils:
In alkaline water areas, lime deposits can accumulate
rapidly inside the coil pipes. This growth is increased by
the extreme heat build up in the coil. The best prevention for liming conditions is to use high quality cleaning
detergents. In areas where alkaline water is an extreme
problem, periodic use of Landa Deliming Powder (part
#9-028008) will remove lime and other deposits before
coil becomes plugged. (See Deliming Instructions for
use of Landa Deliming Powder.)
Deliming Coils:
Periodic flushing of coils is recommended.
1. Fill a container with 4 gallons of water, then add 1
lb. of deliming powder. Mix thoroughly.
2. Remove wand assembly from spray gun and put
spray gun into container. Secure the trigger on the
spray gun into the open position.
3. Attach a short section (3-5 ft.) of garden hose to
machine to siphon solution from an elevated container. Turn pump switch on allowing solution to be
pumped through coils back into the container. Solution should be allowed to circulate 2-4 hours.
4. After circulating solution, flush entire system with
fresh water. Reinstall wand assembly to spray
gun.
Removal of Soot and Heating Coil:
In the heating process, fuel residue in the form of soot
deposits may develop between the heating coil pipe
and block air flow which will affect burner combustion.
When soot has been detected on visual observation,
the soot on the coil must be washed off after following
the coil removal steps.
16
LANDA VHP • 8.913-949.0 • Rev. 5/13
1.Remove the tank head assembly by unscrewing
the three Tek screws and lifting the tank head off.
2. Remove the two pipe nipples and associated fittings.
3. Lift the coil out of the outer wrap.
CAUTION:The coil weighs about 80 lbs. Use proper
lifting techniques.
4. Clean, repair and replace the coil by reversing the
above steps.
Pressure Relief Valve:
Each machine is equipped with a relief valve to relieve
pressure in the system when higher than normal operating pressures are encountered. Unusually high pressures come from an object plugging the spray nozzle.
This problem can easily be remedied by removing the
obstruction. If operating pressure of machine is found
to be normal and relief valve continues to leak, repair
or replace the valve.
Propane Cylinder Capacity:
An important consideration with propane systems is the
capacity of the supply cylinder relative to the needs of
the burner. The burner operates on propane as a gas;
as gas is used from the propane cylinder, the liquid in
the cylinder boils to maintain gas pressure. This boiling
process cools the liquid, and in a heavy, continuousdemand situation, the liquid temperature can fall to
the point at which it cannot provide gas as rapidly as
is needed. In this case, it may be necessary to warm
the propane cylinder by directing a warm spray, not
over 120° F, on the cold cylinder or by manifolding two
propane bottles together to increase total vaporization
capacity. It is recommended that a minimum 30 lb.
vapor propane bottle be used on the machine.
PRESSURE WASHER OPERATOR’S MANUAL
Maintenance & Service
Rupture Disk
If pressure from pump or thermal expansion should
exceed safe limits, the rupture disk will burst, allowing
high pressure to be discharged through hose to ground.
When disk ruptures, it needs to be replaced.
oil change record
Date Oil Changed
Month/Day/Year
No. of Operating
Hours Since
Last Oil Change
Date Oil Changed
Month/Day/Year
No. of Operating
Hours Since
Last Oil Change
17
LANDA VHP • 8.913-949.0 • Rev. 5/13
33
TING
RA
IN
RU
ST
NS
IO
CT
PRESSURE WASHER
OPE
ON
CI
RA
IN
RU
ST
NS
IO
CT
D'
OPE
N
TIO
RA
43
48
54
18
LANDA VHP • 8.913-949.0 • Rev. 5/13
131
l.
fue
or
g.
vap
tin
ne
era
pa
op
pro
e
on .
for
be
run ttle
elf g.
to bo
sh
d
ne ne ly. om rtin
pa
sig
on kfr e sta
de a pro g
is to rtin tan for
ne be
t
ine ec po pa al
ch nn ns
nu
ma co tra pro ma
is t for or 's
Th no is vap tor
Do elf ve era
l.
Sh mo op
fue
Re ad
or
Re
g.
vap
tin
ne
era
pa
op
pro
e
on .
for
be
run ttle
elf g.
to bo
sh
d
ne ne ly. om rtin
pa
sig
on kfr e sta
de a pro g
is to rtin tan for
ne be
t
ine ec po pa al
ch nn ns
nu
pro
ma co tra
ma
is t for or 's
Th no is vap tor
Do elf ve era
Sh mo op
l.
Re ad
fue
Re
or
g.
vap
tin
ne
era
pa
op
pro
e
on .
for
be
run ttle
elf g.
to bo
sh
d
ne ne ly. om rtin
pa
sig
on kfr e sta
de a pro g
is to rtin tan for
ne be
t
ine ec po pa al
ch nn ns
nu
ma co tra pro ma
is t for or 's
Th no is vap tor
Do elf ve era
Sh mo op
Re ad
Re
89139490-4
Tank
(Not Included,
Optional)
37
27
112
53
46
43
OPE
55
DE
42
50
S
39
41
21
114
40
125
110
35
28
140
36
30
38
16
NE
IO
24
129
CC
RU
ST
18
15
25
13
31
32
8
15
IN
52
16
111
51
115
116
20
View A-A
108
109
19
6
26
13
29
4
29
23
137
1
17
12 133
3
9
11
2
127
84
10
7
Electronic Ignition
(Optional)
5
OPERATOR’S MANUAL
exploded view — left side
34
14
49
45
47
44
57
61
136
73
77 123
135
Nev
IO
ual.
N
117
107
89139490-3
106
122
95
112
LANDA VHP • 8.913-949.0 • Rev. 5/13
94
105
91
120
101
103
100
95
120
96
89
86
11
119
94
75
98
97
102
102
99
120
97
130
90
112
91 92
139
132
CA
UT
79
88
85
121
121
87
22
119
80
122
· er
· Blea Use
· Liqu ch,
:
· Tri-s ids
· Amm odiu contchlo
ThesAcid
rine
surfa -basonia m ainin
phos prod
Use e
g
ce chem ed prod
phat solve ucts
man bein
prod ucts
icals
e nts and
ufac g
ucts
prod
clea
(i.e. othe
turer will
ucts
ned. harm
pain r
’s
corro
dete
t thinn
the
sive
rgen
unit
er, chem
ts
and
gaso
as
icals
reco will
line,
mme dam
oil)
age
nded
the
in
man
78
93
76
65
72
120
104
126
92
120
95
128
134
82
11
71
64
62
118
83
43
81
69
59
58
68
66
124
133
63
125
92
60
56
68
67
59
70
138
PRESSURE WASHER OPERATOR’S MANUAL
exploded view — Right side
For
Detail See
View A-A
74
19
PRESSURE WASHER
OPERATOR’S MANUAL
Exploded View Parts list
ITEMPART NO.
DESCRIPTIONQTY
ITEMPART NO. DESCRIPTIONQTY
1
8.912-918.0 Cover, Electrical Box
1
29
9.802-695.0 Nut, 10/32” Keps
8
2
9.800-016.0 Label, Disconnect PWR Supply 1
30
9.802-127.0 Nipple, 1/2" JIC x 3/8" Pipe
1
3
9.802-764.0 Screw, 10/32" x 3/4", Hex
2
31
9.802-036.0 Nipple, 1/2" JIC x 3/8" Pipe
1
4 9.802-551.0 Transformer 240/480V - 120V (3-2000)
1
32
9.802-767.0 Screw, 3/8" x 3/4" Whiz Loc
4
33
8.900-822.0 Label, VHP Operating Instr.
1
5 8.716-173.0 Fuse, Paper 1 Amp 250V Midget (3-2000)
1
34
8.706-984.0 Adapter, 1/2" x 1/2" Pipe
1
6 8.933-007.0 Fuse, 1 Amp 600V Midget
(3-2000)
2
35
8.706-844.0 Tee 1/2" Female, Pipe 1
36
8.706-797.0 Nipple, 1/2" Hex
1
37
9.802-128.0 Nipple, 1/2" JIC x 1/2" Pipe
1
38
8.707-254.0 Pump Protector, 3/8" PTP
1
7
9.802-793.0 Nut, Cage, 1/4" x 16 GA.
7
8
8.912-917.0 Box, Electrical, VHW, Belt
1
39 9.802-151.0 Swivel, 1/2" JIC Fem,
Push-On
9.802-762.0▲ Screw, 10/32" x 1-1/4"
1
9.802-695.0▲ Nut, 10/32" Keps
(Electric Ignition)
6
10
9.800-040.0▲ Label, Ground
1
9 8.912-919.0 Cover, Pump & Motor,
VHW Belt
1
10 8.912-888.0 Holder, Wand Bracket,
VHW/VHP
1
11 9.802-754.0 Screw, 1/4" x 1/2", HH NC,
Whiz Loc
42
8.912-873.0 Support, Propane Tank, VHP
1
16
43
9.802-792.0 Nut, Cage, 3/8" x 12 Ga.
16
12
9.800-033.0 Label, Warning Hot Water
1
44
8.912-864.0 Brace, LP Bottle, VHP
1
13
9.802-449.0 Switch, 3 PS, 115V-230V, 1 PH 1
45
8.912-879.0 Bracket, Propane Tank, VHP
1
14
8.912-916.0 Panel, Control, VHW, Belt
46
8.912-882.0 Strap, Propane Tank, R/H VHP 1
47
8.912-885.0 Strap, Propane Tank, L/H VHP 1
48
8.719-063.0 Knob, 3/8" - 16 x 1-1/2" VHP
1
9.804-029.0 Pulley, AK64H, (2-15024D)
9.802-380.0 Pulley, BK80H (3-20024A)
1
1
1
40
4-02110000 Hose, 1/2" Push-On 2
12"
41 9.802-339.0 Motor, 2 HP, 1 PH 3450 RPM,
C-Face (2-1500)
1
9.802-341.0 Motor, 5 HP 1 PH 3450 RPM
C-Face (3-2000)
1
9.800-032.0▲ Label, Motor Overload Reset,
Lexan
1
15 9.802-759.0 Screw, 10/32" x 1/2"
BHSOC BLK
(Electric Ignition)
8
12
16
5
17 9.802-553.0 Transformer, 120/240 -24V
.050 KVA
(Electronic Ignition Option)
49
1
18
9.802-514.0 Strain Relief, 1/2" LQ Tite
4
50 8.715-517.0 Pulley, Bore, AK21 x 5/8"
(2-15024D)
1
9.802-377.0 Pulley, BK32 (3-20024A)
1
9.803-897.0▲ Bushing, H x 3/4 (3-20024A) 1
19
9.802-525.0 Locknut, 1/2"
4
51
9.802-402.0 Bushing, HX24mm
1
1
52
9.804-026.0 Belt, AX31 (2-15024D)
9.802-413.0 Belt, BX32 (3-20024A)
1
1
9.802-776.0 Nut, 5/16", ESNA, NC
20 9.802-433.0
9.802-431.0
Plug, GFCI, 240V, 20 Amp
(3-2000)
Cord w/GFCI, 120V 20 Amps
(2-1500)
1
21
8.932-969.0 Label, Warning, Service Cord
1
22
9.802-772.0 Screw, 10/32" x 1/4"
2
23
9.802-771.0 Screw, 10/32" x 3/4"
4
24 9.802-146.0 Swivel, 1/2" MP x 3/4" GHF
w/Strainer
1
25
1
8.933-006.0 Switch Flow MV 60, Yellow
26 8.918-210.0 Hose, 3/8" x 16", 2 Wire,
Pressure Loop
1
27 8.750-299.0 Unloader, VRT 3, 8 GPM
@4500 PSI
1
28
1
8.706-168.0 Elbow, 3/8" Male Pipe
20
LANDA VHP • 8.913-949.0 • Rev. 5/13
ITEMPART NO.
53
DESCRIPTIONQTY
8.717-749.0 Regulator, Propane, R532CFF 1
54 8.711-851.0 Hose, 3/8" x 10',
Propane Assembly
1
55 8.717-790.0 Tank, Propane 10.5 Gal. 30 lb. w/ Gauge Optional
1
56
8.712-185.0 Switch, Snap, 225 DR Hi-Limit 1
57
9.149-003.0 Manifold Coil Outlet Discharge 1
58
9.802-171.0 Nipple, 3/8" x 3/8" NPT ST Male1
59
9.802-013.0 Nipple, 1/2" x 2.5" Galv.
2
60
8.706-248.0 Plug, 3/8" Allen Counter sunk
1
61
8.706-216.0 Tee, 1/2", FPT Steel
1
62
4-02110000 Hose, 1/2", Push-On
2.5 ft.
63 9.802-043.0 Elbow, 1/2" JIC x 1/2" Fem,
90 DGR
1
64 8.915-981.0 Wrap, Outer Coil, VHW
9.800-021.0▲ Label, Hot Water Outlet
1
1
65
1
9.803-134.0 Coil, Dura, 14.5" Dia, Sch 80
66 8.719-968.0 Holder, Wand, VHW/VHP
Zinc Plated
67 9.803-029.0 Tank Head Assembly,
16" Dia x 8" Stack
1
ITEMPART NO.
DESCRIPTIONQTY
86 8.718-150.0 Pilot, VHP
1
8.718-075.0▲ Orifice, Pilot, LP, Small
1
9.803-610.0▲ Pilot, Ignitor (Electric Ignition)1
9.803-562.0▲ Cable, Ignition, 48” (Electric
Ignition)
1
87 8.718-092.0 Thermocouple, 24"
White Rodgers
1
88
1
9.802-681.0 Wire, 15" Assembly
9.802-682.0▲ TCB, GND
1
89
1
8.718-069.0 Electrode, Piezo Assembly
90 9.802-911.0 Tubing, Aluminum, 1/4"
Deadsoft
36"
91
8.912-868.0 Axle, 23", VHW
2
92
90-4005
4
93
9.800-031.0 Label, VHP Pilot Light
94
4-0303
95
9.802-782.0 Collar, 5/8" Bore Shaft
4
96
9.802-027.0 Elbow, 3/4", Black, 90°
1
97
9.802-018.0 Nipple, 3/4" x 3". Black Pipe
2
98
9.802-049.0 Union, 3/4", Black Pipe
1
Washer, 5/8", Flat, SAE
1
Wheel and Tire Assy, 4" w/Tube 4
4
99 8.718-045.0 Valve, Gas,
WR 36103A-410, 3/4"
9.803-616.0▲ Valve, Gas (Elec Ign)
9.803-618.0▲ LP convert Kit (Elec Ign)
1
1
1
1
100 8.912-858.0 Axle, Holder Assembly
VHW/VHP
2
101 8.706-108.0 Nipple, Blk, Pipe 3/4" x 3-1/2"
1
2
1
68
9.800-006.0 Label, "Hot/Caliente" w/Arrows 2
69
9.802-825.0 Retainer Clip
70 9.802-904.0 Insulation, Tank Head
16" OD x 8" ID
71
8.912-899.0 Handle, VHW/VHP/MVP w/HNG1
72
8.912-871.0 Panel, Chassis, Front/Back
73
8.912-881.0 Reflector, Pilot Light, VHP/VHG 1
102 8.718-648.0 U-Bolt, 1/4" x 1-1/2" x 2-1/2"
w/Plate
74
9.802-678.0 Ignitor, Piezo
1
103 8.706-108.0 Nipple, 3/4" x 3-1/2", Black Pipe 1
75
8.912-875.0 Support, Burner Ring
1
104 8.706-222.0 Tee, 3/4" NLK Pipe
1
4
105 9.802-018.0 Nipple, 3/4" x 3", Black Pipe
1
106 8.706-320.0 Cap, 3/4", Black Pipe
1
76 9.802-778.0 Nut, Whiz Loc 5/16 Flange
1
77 8.904-857.0 Pump, Landa LD3030,
3@ 3000 1
78
8.912-920.0 Retainer, Take-up, Pump
1
79
9.802-733.0 Bolt, 3/8" x 3-1/2" Tap
2
80
9.803-131.0 Rail, Pump Combo 1
81
8.912-923.0 Base, Main, VHP, Belt
1
82 8.718-054.0 Burner Ring, X-11 w/640-69
Jet Orifices
1
83 9.802-064.0 Grommet, Rubber,
Nozzle Holder
1
84 9.802-463.0 Fuse, Paper, Buss FNM-1/2
250V Midget TD
(Electronic Ignition Option)
1
PRESSURE WASHER OPERATOR’S MANUAL
Exploded View Parts list
107 8.912-877.0 Support, Gas Train, VHP/VHG 1
108 9.804-608.0 Cap, Vinyl FKT (Yellow)
1
109 8.912-930.0 Assy, Lever Brake
1
110 8.912-928.0 Bracket, Wheel Brake
1
111 8.718-980.0 Washer, 5/16", Flat, SAE
12
112 9.802-775.0 Nut, 1/4" Flange, Whiz Loc
8
85 8.912-890.0 Bracket, Pilot Light, VHP/VHG 1
8.719-957.0 Bracket, Pilot Light, VNG-S (Electric Ignition)
1
21
LANDA VHP • 8.913-949.0 • Rev. 5/13
PRESSURE WASHER
OPERATOR’S MANUAL
Exploded View Parts list
ITEMPART NO.
DESCRIPTIONQTY
114 8.725-394.0 Washer, 3/8", SAE, Flat
8
115 8.718-785.0 Screw, 3/8" x 3/8", SCKT
SHDR, Zinc
1
116 90-1995
Screw, 1/4" x 1/2" BH SOL CS 4
ITEMPART NO. DESCRIPTIONQTY
129 8.900-300.0 Label, Landa
1
130 8.932-963.0 Label, Liquid Propane
1
131 8.900-829.0 Label, VHP, Propane Tank
1
132 8.912-894.0 Brace, Chassis
1
117 9.802-684.0 Jet Orifice #69, Drill to #66 32
133 9.184-030.0 Spacer, Rupture Disk
1
118 9.802-769.0 Screw, 3/8" x 1-3/4" Whiz Loc
4
119 9.802-781.0 Nut, 3/8" Flange Whiz Loc
11
134 8.707-019.0 Hose Barb, 1/2" Barb x 3/8"
MPT, Push-On
1
120 9.802-767.0 Screw, 3/8" x 3/4" Whiz Loc
18
135 9.800-018.0 Label, Tipover Hazard
1
121 8.932-965.0 Label, Exposed Pulley
2
122 9.802-794.0 Nut, Cage, 1/4" x 12 GA
10
136 9.800-049.0 Label, Manufacturer's
Cleaning Solutions
1
123 8.706-168.0 Elbow, 3/8" Male Pipe 1
137 9.803-613.0 Module, Ignition (Electric Ign.) 1
124 9.151-014.0 Rupture Disk, 5000 PSI
1
138 9.803-108.0 Retainer Ring, Insulation
1
125 8.916-090.0 Label, Landa
2
139 8.718-618.0 Bolt, 5/16" x 3/4" NC
4
126 8.706-109.0 Nipple, 3/8" x 7", Black Pipe
1
140 9.802-518.0 Strain Relief 3/4
1
127 8.933-007.0 Fuse, KTK-R1 600V
Midget Fuse
(Electronic Ignition Option)
2
128 90-19710
5
Screw, 1/4" x 3/4", Whiz Loc
22
LANDA VHP • 8.913-949.0 • Rev. 5/13
▲ Not Shown
PRESSURE WASHER OPERATOR’S MANUAL
Hose & Spray Gun Exploded View
2
1
High Pressure
Nozzle
6
8
5
7
4
3
Hose & Spray Gun Exploded View Parts list
ITEMPART NO.
DESCRIPTIONQTY
ITEMPART NO.
1 9.802-224.0 Downstream Injector Assy.,
Non Adj #2, 2-3 GPM
1
9.802-096.0▲ Quick Coupler O-Ring, 1/4" 1
2
1
Nozzle, SAQCMeg 1503,
Yellow (2-1500)
Nozzle, SAQCMEG, 15035,
Yellow (3-2000)
Nozzle, SAQCMEG 1504,
Yellow (2-1100)
Nozzle, SAQCMEG 1505.5
Yellow (3-700)
▲ Not Shown
9.802-166.0 Coupler, 3/8" Female
7
DESCRIPTIONQTY
9.802-165.0 Coupler, 1/4" Male, Brass
3 8.739-026.0 Hose, 3/8" x 50', 1-Wire,
Tuff-Skin
1
4 8.751-234.0 Gun, Landa, L1050,
5000 PSI, 10.4 GPM
1
5
8.711-293.0 Wand, Only, VP, Zinc
1
8 8.712-333.0
8.712-338.0
8.712-346.0
8.712-358.0
6
9.802-286.0 Brass Soap Nozzle, 1/8"
1
9.802-100.0▲ Quick Coupler O-Ring, 3/8" 1
1
1
1
1
1
23
LANDA VHP • 8.913-949.0 • Rev. 5/13
8.725-169.0 LD 3025R.1
8.904-857.0 LD 3030R.1
8.904-856.0 LD 4020R.1
OPERATOR’S MANUAL
PRESSURE WASHER
LD.1 Series Pump exploded view
TORQUE
SPECS
Item #
Ft.-lbs
14
65
17
18
25
7.6
34
7
44
13
LD.1 Series Pump exploded view parts list
itemPart no. Description QTY
itemPart no. Description QTY
1
11* 9.803-947.0 O-Ring Ø1.78 x 15.54
6
3
12* See Kits Below Valve Assembly
6
3
13* 9.803-948.0 O-Ring Ø2.62 x 18.77
6
3
14
9.803-949.0 Valve Plug
6
See Kits Below Pressure Ring 18mm (4020, 3025)
3
15
9.803-950.0 Copper Washer 1/4
1
5*
9.803-938.0 Crankcase 1
2* See Kits Below Plunger Oil Seal
3*
See Kits Below O-Ring Ø1.78 x 28.30
4* See Kits Below Pressure Ring 15mm (3030)
16
9.803-951.0 Brass Plug G1/4
1
See Kits Below U-Seal, 15mm (3030)
3
17
9.803-952.0 Manifold Stud Bolt
8
See Kits Below U-Seal, 18mm (4020, 3025) 3
18 9.802-884.0 Washer
8
6* See Kits Below Intermediate Ring 15mm
(3030)
3
19
9.803-198.0 Copper Washer 3/8
1
See Kits Below Intermediate 18mm
(4020, 3025)
20
9.802-925.0 Brass Plug 3/8
2
3
7* See Kits Below Intermed. Ring 15mm (3030)
3
See Kits Below Intermed. Ring 18mm
(4020, 3025)
12
9.803-953.0 Bearing Cover
2
27
9.803-954.0 Bearing Seal
1
3
28
9.802-914.0 Snap Ring
1
9.803-955.0 Ball Bearing
2
8
9.802-926.0 Brass Plug 1/2"
1
29
9
9.803-199.0 Copper Washer 1/2"
1
30 9.803-956.0 Crankshaft
1
1
31
9.803-167.0 Crankshaft Key
1
32
9.803-957.0 Oil Dipstick
1
10
24
25 9.802-939.0 Screw
26
9.803-946.0 Manifold Housing
LANDA VHP • 8.913-949.0 • Rev. 5/13
itemPart no. Description QTY
33
8.933-010.0 Crankshaft Seal
1
34* See Kits Below Plunger Nut 3
35* See Kit BelowCopper Spacer
3
36* See Kits Below Plunger, 15mm (3030)
3
See Kits Below Plunger, 18mm
(4020, 3025)
3
37* See Kits Below Copper Spacer
3
38* See Kits Below O-Ring Ø1.78 x 5.28
3
39* See Kits Below Teflon Ring
3
40* See Kits Below Plunger Rod
3
41
9.803-965.0 Connecting Rod Pin
3
42
9.803-966.0 Connecting Rod
3
43
9.803-218.0 Spring Washer
6
44
8.933-020.0 Connecting Rod Screw
6
45
9.803-202.0 Sight Glass
1
46 9.803-197.0 Gasket
1
47
9.803-968.0 Crankcase Cover
1
48
9.803-969.0 O-Ring Ø2.62 x 107.62
1
PRESSURE WASHER OPERATOR’S MANUAL
LD.1 Series Pump exploded view parts list (cont)
* Available in kit (See below)
Repair kit
number
8.725-354.0
8.725-356.0
8.725-355.0
8.725-357.0
9.803-934.0
9.803-935.0
9.803-936.0
9.803-937.0
Plunger Seal
15mm
LD-3030
Plunger Seal
18mm
LD-3025
LD-4020
Complete Seal
Packing,
15mm
LD-3030
Complete Seal
Packing, 18mm
LD-3025
LD-4020
Plunger
15mm
LD-3030
Plunger
18mm
LD-3025
LD4020
Complete
Valve
Plunger Oil
Seals
item numbers
included
3, 5, 7
3, 5, 7
3, 4, 5,
6, 7
3, 4, 5,
6, 7,
34, 35, 36,
37, 38
34, 35, 36,
37, 38
11, 12, 13
2
Number of
cylinders kit
will service
3
3
1
1
1
1
6
3
KIT DESCRIPTION
25
LANDA VHP • 8.913-949.0 • Rev. 5/13
8.750-297.0, 8 GPM, 2320 PSI
8.750-298.0, 8 GPM, 3630 PSI
8.750-299.0, 8 GPM, 4500 PSI
20
OPERATOR’S MANUAL
PRESSURE WASHER
VRT3 Unloader exploded view and parts list
DESCRIPTIONQTY
25
18
8.750-713.0
8.750-712.0
Outlet Fitting
Knob, Unloader
8.750-709.0
Repair Kit, VRT3, 2320/3630 PSI
8.750-710.0
Repair Kit, VRT3, 4500 PSI
14
19
ITEMPART NO.
1
1
(Kit Items: 3, 4, 6, 9-12, 21, 24)
8
9
18
10
9
26
17
1
22
16
23
3
15
15
13
21
4
5
25
6
6
12
11
24
7
2
Unloader Adjustment Procedures
1.
2.
3.
4.
5.
Remove lock nut (Item 19).
Remove adjustment knob (Item 18).
Loosen the two (2) nuts (Item 15), move them upward on stem (Item 8) until you see 4 or more threads below the nut.
Re-attach adjusting knob (Item 18).
Start machine. Open the trigger of the spray gun. Increase pressure by turning adjustment knob (Item 18) clockwise until
pressure is at the desired operating pressure.
6. Remove the adjustment knob (Item 18), tighten the lower nut (Item 15) tightly against the upper nut (Item 15).
Re-attach adjustment knob (Item 18) and screw down until contact is made with the nuts (Items 15). Screw down lock nut
(Item 19) onto the stem (Item 8) until the threads cut into the nylon insert of the lock nut (Item 19).
*If adjustment knob (Item 18) DOES NOT make contact with upper nut (Items 15), remove adjusting knob (Item 18), re-adjust
(raise) nuts (Items 15) on stem (Item 8) and re-attach adjustment knob (Item 18), then repeat step #6.
**If adjustment knob (Item 18) DOES make contact with upper nut; release the trigger of the spray gun and watch the
pressure gauge for the pressure increase (“spike”). This “spike” SHOULD NOT exceed 500 psi above the operating pressure.
If “spike” pressure exceeds the 500 psi limit, remove the adjusting knob (Item 18) and re-adjust (lower) the nuts (Items 15)
on the stem (Item 8). Re-attach the adjusting knob (Item 18), then repeat step #6.
26
LANDA VHP • 8.913-949.0 • Rev. 5/13
3-700, 3-1100, 3-2000
1
PRESSURE WASHER OPERATOR’S MANUAL
injector assemblY #2 — 4-011182
2
3
4
ITEMPART NO.
DESCRIPTIONQTY
1 9.802-215.0 Injector, Detergent, Non Adjust,
#2, 2-3 GPM
1
2 6.390-126.0 Clamp, Hose, .46-, .54 ST1
3
4-02080000 Tube, 1/4" x 1/2", Clear Vinyl 6 ft.
4
8.707-057.0 Strainer, 1/4", Hose Barb
1
27
LANDA VHP • 8.913-949.0 • Rev. 5/13
PRESSURE WASHER WARRANTY
28
LANDA LIMITED NEW PRODUCT WARRANTY
PRESSURE WASHERS
WHAT THIS WARRANTY COVERS
All LANDA pressure washers are warranted by LANDA to the original purchaser to be free from defects in materials
and workmanship under normal use, for the periods specified below. This Limited Warranty is subject to the exclusions
shown below, is calculated from the date of the original purchase, and applies to the original components only. Any parts
replaced under this warranty will assume the remainder of the part’s warranty period.
SEVEN YEAR PARTS AND ONE YEAR LABOR WARRANTY:
Components manufactured by LANDA, such as frames, handles, top and bottom wraps, float tanks, fuel tanks, belt
guards, and internal components on the oil-end of Landa manufactured pumps. General, AR, Liberty, Comet and swash
and wobble plate pumps have a one year warranty. Heating coils have a five year warranty from date of original machine
purchase.
ONE YEAR PARTS AND ONE YEAR LABOR WARRANTY:
All other components, excluding normal wear items as described below, will be warranted for one year on parts and
labor. Parts and labor warranty on these parts will be for one year regardless of the duration of the original component
manufacturer’s part warranty.
WARRANTY PROVIDED BY OTHER MANUFACTURERS:
Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these
manufacturers’ local authorized service centers. LANDA is not authorized and has no responsibility to provide warranty
service for such components.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover the following items:
1. Normal wear items, such as nozzles, spray guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings, packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump
protectors.
2. Damage or malfunctions resulting from accidents, abuse, modifications, alterations, incorrect installation, improper servicing, failure to follow manufacturer’s maintenance instructions, or use of the equipment beyond its
stated usage specifications as contained in the operator’s manual.
3. Damage due to freezing, chemical deterioration, scale build up, rust, corrosion, or thermal expansion.
4. Damage to components from fluctuations in electrical or water supply.
5. Normal maintenance service, including adjustments, fuel system cleaning, and clearing of obstructions.
6. Transportation to service center, field labor charges, or freight damage.
WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE
While not required for warranty service, we request that you register your LANDA pressure washer by returning the completed registration card. In order to obtain warranty service on items warranted by LANDA, you must return the product
to your Authorized LANDA Dealer, freight prepaid, with proof of purchase, within the applicable warranty period. If the
product is permanently installed, you must notify your Authorized LANDA Dealer of the defect. Your Authorized LANDA
Dealer will file a claim with Landa, who must subsequently verify the defect. In most cases, the part must be returned
to LANDA freight prepaid with the claim. For warranty service on components warranted by other manufacturer’s, your
Authorized LANDA Dealer can help you obtain warranty service through these manufacturers’ local authorized service
centers.
LIMITATION OF LIABILITY
LANDA’S liability for special, incidental, or consequential damages is expressly disclaimed. In no event shall LANDA’S
liability exceed the purchase price of the product in question. LANDA makes every effort to ensure that all illustrations
and specifications are correct, however, these do not imply a warranty that the product is merchantable or fit for a
particular purpose, or that the product will actually conform to the illustrations and specifications. Our obligation under
this warranty is expressly limited at our option to the replacement or repair at a service facility or factory designated by
us, of such part or parts as inspection shall disclose to have been defective. THE WARRANTY CONTAINED HEREIN
IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF
MERCANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO THE DURATION
OF THIS WRITTEN WARRANTY. LANDA does not authorize any other party, including authorized LANDA Dealers, to
make any representation or promise on behalf of LANDA, or to modify the terms, conditions, or limitations in any way.
It is the buyer’s responsibility to ensure that the installation and use of LANDA products conforms to local codes. While
LANDA attempts to assure that its products meet national codes, it cannot be responsible for how the customer chooses
to use or install the product. Some states do not allow limitations on how long an implied warranty lasts or the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
LANDA
www.landa.com
LANDA VHP • 8.913-949.0 • Rev. 5/13
Gracías por comprar un Lavadora a Presión Landa.
Estas instrucciones y advertencias corresponden a
los modelos VHP.
Landa se reserva el derecho de hacer cualquier
cambio en cualquier momento sin contraer ninguna
obligación.
Responsabilidades del Dueño/Usuario:
El dueño y/o usuario debe estudiar y mantener las
instrucciones del fabricante para futuras referencias.
Cuidar estas instrucciones
Este manual debe ser considerado una parte permanente de la máquina y debe quedarse consigo
si máquina es revendida. Al ordenar las partes,
especifican por modelo y número de serie. Utilice
repuestos sólo idénticos. Esta máquina debe ser
utilizada solamente por los operadores entrenados.
SEGURIDAD DE LA MAQUINA
PRECAUCION: Para reducir el
riesgo de accidentes, lea las
instrucciones cuidadosamente
antes de usar la unidad.
1. Lea todo el manual para operadores cuidadosamente.
Al no seguir las instrucciones
puede causar el mal funcionamiento de la unidad y
provocar la muerte, o causar serias heridas y/o
daños en la propiedad.
2. Todas las instalaciones deben cumplir con los códigos locales. Póngase en contacto con un técnico
eléctrico, plomero, compañía de servicios públicos
o distribuidor de ventas para mayores detalles.
WARNING
ADVERTENCIA
WARNING
ADVERTENCIA
ADVERTENCIA: Riesgo de asfixia. Use este producto solo en
areas bien ventiladas.
3. Evite instalar unidades en
áreas pequeñas o cerca de
ventiladores de gases de escape. Los gases de escape
contienen gas venenoso de
ADVERTENCIA: Liquidos inflamables pueden crear gases
que se encienden causando
daños a la propiedad y heridas
severas.
4. Aparatos de encendido con
petróleo deberán de ser instalados en lugares donde
residuos de combustibles, vapores o gases inflamables no estén normalmente presentes.
En modelos de encendido con petróleo utilice únicamente kerosene #1 o diesel. No utilize gasolina,
solventes o alcohol. El utilizarlo resultará en fuego
y/o explosión.
WARNING
ADVERTENCIA
ADVERTENCIA: mantenga el
chorro de agua, la varilla y la
manguera de alta presion lejos
del cableado electrico ya que
puede ocurrir un choque fatal.
lea la etiqueta de avertencia del
cable electrico.
5. Para proteger al operador de
un choque eléctrico, la máquina deberá de estar
conectada a tierra. Es la responsabilidad del
dueño de conectar esta máquina a un receptáculo a tierra aprobado por UL con el amperage y
voltaje indicados. No moje sobre o cerca de los
componentes eléctricos; no toque la máquina con
las manos mojadas o cuando esté parado sobre
agua. Siempre desconecte la máquina cuando le
dé servicio de mantenimiento.
WARNING
ADVERTENCIA
MANUAL DEL OPERADOR
El dueño y/o usuario debe estar al tanto de las instrucciones de operación y de las advertencias del
fabricante antes de usar su lavadora a presión Landa.
La información de advertencia debe ser enfatizada y
comprendida. Si el operador no domina el inglés, el
comprador/dueño deberá leer y discutir con éste las
instrucciones y las advertencias del fabricante en el
idioma natal del operador, asegurándose de que éste
entienda su contenido.
monóxido decarbono; la exposición puede causar
pérdida del conocimiento y causar la muerte. Los
gases de escape también contienen químicos, en
ciertas cantidades, que se sabe, causan cáncer,
defectos de nacimiento, o daños al sistema reproductivo.
EQUIPO DE LAVADO A PRESIÓN
introduccion & seguridad de la maquina
ADVERTENCIA: Sostenga la pistona aspersora con ambas manos ya que con la alta
presion esta puede tener retroceso.
6.Sujete firmemente con ambas manos la varilla
aspersora antes de encender la maquina; de no
seguir esta recomendación puede resultar en
heridas por golpe de la misma.
7. No coloque la máquina cerca de objetos inflamables si el motor esta caliente.
29
LANDA VHP • 8.913-949.0 • Rev. 5/13
EQUIPO DE LAVADO A PRESIÓN
MANUAL DEL OPERADOR
seguridad de la maquina
ADVERTENCIA: Este equipo
puede producir un fluido de
alta presion a chorro que puede
penetrar la piel y sus tejidos,
causando graves heridas y
posible amputacion.
8. No reemplazar el tanque
depropano líquido mientras la unidad está funcionando. Podrían ocurrir accidentes
serios.
ADVERTENCIA
WARNING
ADVERTENCIA
WARNING
ADVERTENCIA: Usar combustible líquido solamente.
9. Este equipo está diseñado
para funcionar a gas. No usar
combustible líquido. Disponer
de un técnico de servicio calificado para instalar y proveer
servicio de mantenimiento a
su equipo.
15. Los gases de propano líquido son más pesados
que el aire y se esparcirán sobre el piso. Proveer
siempre espacio y ventilación adecuados alrededor de estas unidades.
16. Durante las reparaciones, desconectar el suministro eléctrico y cerrar la válvula de gas.
17.Apagar el quemador, abrir la pistola de paso y
enfriar hasta 100° F antes de apagar la máquina.
18. La máquina no debe estar desatendida durante la
operación.
19. No adecuada para conectar un respiradero de gas
Tipo B, si la temperatura de la chimenea excede
243° C (470° F).
20. Sila máquina va a ser instalada en forma permanente, instalar una campana de tiro con la descarga
de gases fuera del edificio.
ADVERTENCIA
WARNING
10. El agua de ingreso debe estar fría.
11. No operar el equipo cuando se esté fatigado o bajo
la influencia de alcohol o drogas. Mantener el área
de operación libre de personas.
12. Nunca producir chispas o llamas donde exista la
presencia de gas.
13. Nunca intentar encender el piloto a menos que la
válvula manual haya estado cerrada por 5 minutos.
14. Nunca operar la máquina con el tanque de propano
líquido colocado en el soporte. Retirar el tanque
de propano líquido de la máquina tan lejos como
lo permita la manguera.
30
LANDA VHP • 8.913-949.0 • Rev. 5/13
ADVERTENCIA: Si se percibe
olor a gas, cerrar el suministro
de gas.
21.Si se percibe olor a gas,
cerrar el suministro de gas,
apagar toda llama abierta y
revisar las uniones aplicando
una solución de jabón. Si
el olor persiste, llamar a su
proveedor de gas inmediatamente.
Este equipo es para uso en interior.
aire de combustión a través de aberturas especiales,
una cerca del piso y otra cerca del techo; cada una
medida en base a una pulgada cuadrada o más de
área libre por cada 1,000 BTU de consumo por hora.
Ubicación:
Colocación:
Colocar la máquina en una ubicación conveniente,
con amplio apoyo, drenaje y espacio para servicio de
mantenimiento.
La ubicación deberá proteger la máquina de las condiciones perjudiciales del medio ambiente, tales como
viento, lluvia y congelamiento.
Regulaciones Sobre Gases:
Consultar con la compañía de gas local y con las
autoridades municipales respecto a las normas o
regulaciones específicas que rijan el montaje. El montaje debe hacerse de acuerdo con las regulaciones
municipales locales.
Aspecto Eléctrico:
Esta máquina, al ser instalada, debe ser puesta a tierra
según las regulaciones municipales locales. Verificar el
adecuado suministro de energía usando un voltímetro.
El voltímetro VHP2-15021D requiere un receptáculo
de 20 amp para cumplir con los estándares de certificación UL 1776.
Respiradero:
Cuando la lavadora a presión es instalada en un
espacio muy estrecho sin aberturas de ventilación
al exterior, deben tomarse medidas para suministrar
Permitir suficiente espacio para dar servicio de mantenimiento a la unidad.
Regulaciones municipales locales requieren mantener ciertas distancias entre el piso y las paredes.
(Dos pies de distancia deberían ser suficientes.)
Suministro de Agua:
El suministro de agua para la unidad deberá ser provisto por una manguera de jardin de 5/8” de diámetro
interno con una presión de agua local no menor a 30
psi. Si el suministro de agua es insuficiente, o si la
manguera está torcida, la unidad funcionará mal y el
quemador no arrancará.
Conexión:
Conectar la varilla, boquilla y pistola (como corresponda). En las conexiones de tubería de rosca,
usar cinta de teflón para evitar fugas de agua. (Ver
Identificación del Componente.)
MANUAL DEL OPERADOR
1.La máquina deberá funcionar en una superficie
nivelada donde no sufra la influencia de factores
externos tales como vientos fuertes, temperaturas
de congelamiento, lluvia, etc. Al seleccionar la
ubicación, considerar accesibilidad para reemplazar Tanques de propano líquido, reabastecer
detergentes, reajustes y mantenimiento. El operador deberá tomar precauciones para prevenir
los excesos de humedad que puedan afectar los
componentes eléctricos.
2. Es recomendable hacer una partición entre el área
de lavado y la máquina para prevenir el rociado
directo de la pistola cuando está en contacto con
la máquina. La humedad excesiva en los controles
eléctricos reducirá la vida útil de la unidad y podría
causar cortocircuitos.
3.Durante el montaje, evitar áreas con ventilación
insuficiente o áreas donde los ventiladores generen insuficiente suministro de oxígeno. Se puede
obtener una buena combustión, solamente cuando
hay suficiente suministro de oxígeno disponible
para la cantidad de combustible incinerado. Si se
instala en una área con ventilación insuficiente,
suministrar aire fresco exterior al quemador con un
ventilador instalado dentro del ambiente. Evitar espacios estrechos o áreas cerca de ventiladores.
No colocar la máquina cerca de materiales combustibles. Mantener todo material inflamable a 20 pies de
distancia por lo menos.
EQUIPO DE LAVADO A PRESIÓN
instalacion
Conectar la manguera de alta presión al niple de descarga jalando el collar de acoplamiento hacia atrás e
insertándolo en el niple de descarga. Luego, empujar
el collar hacia adelante para asegurarlo. Un inyector
detergente podría ser insertado entre el acoplamiento
de la manguera y el niple de descarga.
Colocar el tubo de productos detergentes en el jabón
líquido o solución detergente. Evitar que el tubo succione aire.
PRECAUCION: Al instalar la manguera de gas
propano al Tanque de propano líquido, por favor,
notar que las roscas están hacia la izquierda.
Inspección y Prueba:
Antes de mantener el gas a presión en las tuberías,
cerrar todas la aberturas por donde pueda escapar
el gas. Inmediatamente después de encender el gas,
debe revisarse el sistema en busca de fugas. Esto
puede hacerse observando el indicador de prueba de
½ pie cúbico y esperando 5 minutos para observar
cualquier movimiento, o aplicando una solución de
jabón a cada conexión de la tubería y observando las
burbujas. Si se detectan fugas, hacer las reparaciones
necesarias y repetir la prueba anterior.
LANDA VHP • 8.913-949.0 • Rev. 5/13
31
EQUIPO DE LAVADO A PRESIÓN
MANUAL DEL OPERADOR
instalacion
Las tuberías y accesorios defectuosos deben ser cambiados, no deben ser reparados. Nunca usar ningún
tipo de llama o fuego para localizar fugas de gas, usar
una solución de jabón.
Luego que la tubería y el medidor han sido revisados
completamente, purgar el aire del sistema. NO purgar
el aire dentro de un ambiente cerrado.
La lavadora a presión y la válvula individual de cierre
deben ser desconectados del sistema de tuberías de
suministro de gas durante la prueba de presión donde
una presión sobre ½ psig podría dañar la válvula de
gas.
Válvula de Cierre:
Se ha instalado una válvula de cierre entre la línea
de suministro de gas y la lavadora. La instalación
también incluye una unión entre la válvula de cierre
y el quemador.
Condensación en los Serpentines:
Cuando se bombea agua fría por los serpentines del
calentador y los quemadores están encendidos, se producirá condensación sobre los serpentines y goteará
al compartimiento del quemador dando la impresión
de fugas en los serpentines, particularmente en días
húmedos y fríos.
Revisar el Serpentín del Calentador de
Agua en busca de Fugas:
2.ANTES DE ENCENDER revisar alrededor del
equipo para detectar posible olor a gas. Revisar
al nivel del piso ya que el gas propano es más
pesado que el aire y se acumula sobre el piso.
Para su seguridad: ”¿Qué hacer si se detecta
olor a gas?”
a.No tratar de encender ningún equipo.
b.No tocar ningún interruptor eléctrico; no
usar ningún teléfono del edificio.
c.Llamar inmediatamente a su proveedor
de gas usando un teléfono del vecindario.
Seguir las instrucciones de su proveedor
de gas.
d.Si no se puede ubicar a su proveedor de
gas, llamar al departamento de bomberos.
3. Usar solamente la mano para presionar o girar la
perilla de control del gas. Nunca usar herramientas. Si no se puede presionar o girar la perilla
con la mano, no tratar de repararla, llamar a un
técnico de servicio calificado. El uso de fuerza
durante la reparación podría resultar en incendio
o explosión.
4.No usar la máquina cuando una de sus partes
ha estado sumergida en agua. Llamar inmediatamente a un técnico de servicio calificado para
revisar la máquina y reemplazar cualquier parte
del sistema de control o de control de gas que ha
estado sumergida en agua.
Con el quemador “APAGADO” arrancar la unidad de
bombeo y dejar que funcione por unos minutos. Observar el compartimiento del quemador con una lámpara
o una linterna de mano. Si no se observa ninguna
fuga, el goteo de agua del serpentín será producto
de la condensación de gases combustibles cuando el
quemador está encendido, como se ha descrito en el
párrafo anterior.
INSTRUCCIONES
PARA EL ENCENDIDO
ADVERTENCIA
WARNING
ADVERTENCIA: El incumplimiento de las instrucciones
podría resultar en incendio o
explosión causando daños a la
propiedad, accidentes personales o fatales.
1. El equipo tiene un piloto que
puede ser encendido en
forma manual. Al encender
el piloto, seguir éstas instrucciones en forma estricta.
32
LANDA VHP • 8.913-949.0 • Rev. 5/13
6. Abrir la válvula del Tanque de propano líquido, luego presionar ligeramente la perilla de la válvula del
control principal de gas que está sobre el costado
derecho de la máquina y girar en dirección opuesta
las agujas del reloj a la posición Piloto. NOTA: la
perilla no puede ser girada de “Piloto” a “APAGADO” a menos que sea presionada ligeramente.
7.Presionar la perilla de control completamente y
mantenerla en ésa posición. Después de cinco
(5) segundos, presionar el encendedor rojo hasta
escuchar un sonido fuerte. Repetir este paso 3 ó 4
veces, si fuera necesario, hasta encender el piloto.
Si el piloto no enciende, repetir la operación permitiendo un período de tiempo más largo antes de
soltar la perilla de la válvula de gas. Después que
el piloto encienda, continuar manteniendo la perilla
de control hacia abajo aproximadamente por un
(1) minuto antes de soltarla. Observar la mirilla del
piloto en la parte posterior de la máquina.
8.Girar la perilla de control de gas en el sentido
opuesta a las agujas del reloj hasta el punto de
“ENCENDIDO.”
9. Para operar con agua fría, girar el interruptor a la
posición de la bomba y accionar el gatillo de la
pistola de rociado.
• Asegure la boquilla de alta presión en el ex
tremo de la varilla.
• Gire la manilla para ajustar la presión.
• Para aplicar detergente debe usarse baja presión.
• Lea el manual para operar, previamente.
10. Para operar con agua caliente, girar el interruptor
a la posición del quemador y accionar el gatillo de
la pistola de rociado.
11.Para aplicar detergente, leer las instrucciones
sobre el uso del inyector detergente.
12. Para Detener: limpiar las líneas de productos detergentes con agua fresca, cambiar a la posición
de la bomba y continuar rociando agua hasta
enfriar el quemador.
13.Después que el agua se ha enfriado, apagar la
bomba. Apagar la llave principal de gas, luego
cerrar la válvula del Tanque de propano líquido.
Revisar que el Tanque de propano líquido esté fijo
a la máquina cuando ésta sea transportada.
14. Cerrar el agua. Para protección contra el congelamiento, accionar el gatillo de la pistola de rociado
para drenar el agua del sistema.
MANUAL DEL OPERADOR
1.ALTO! Leer cuidadosamente el manual del
operador antes de operar esta máquina. El incumplimiento de las instrucciones y advertencias
puede causar una operación defectuosa de la
unidad y puede causar heridas serias y/o daños
a la propiedad.
2. Apagar todos los interruptores.
3. Retirar y colocar el Tanque de propano líquido de
la máquina tan lejos como lo permita la manguera
de suministro.
4.Conectar la manguera de suministro de agua y
abrir el agua. Accionar el gatillo de la pistola de
rociado y dejar fluir agua hasta descargar todo el
aire del sistema. Revisar si hay fugas de agua y
ajustar según sea necesario.
5. Conectar el cable de energía a la conexión eléctrica apropiada de acuerdo a la información de
la placa de serie. Presionar el botón de reajuste
GFCI. El voltímetro VHP2-15021 D requiere un
receptáculo de 20 amp para cumplir con la certificación UL.
EQUIPO DE LAVADO A PRESIÓN
INSTRUCCIONES DE OPERACION
Para Usar Vapor:
(Modelo VHP3-70021D solamente)
1.Girar la perilla del control en descargador en el
sentido opuesta a las agujas del reloj. Esto reduce
el fluir del agua por el serpentín.
2. La presión del agua disminuirá aproximadamente
a 250 psi y la temperatura aumentará aproximadamente 250° F.
3. Después de usar vapor, girar la perilla del control
en el descargador en el sentido de la agujas del
reloj hasta que pare. Bajará la temperatura. Antes de apagar la lavadora, dejar que funcione sin
prender el quemador para enfriar el serpentín.
Boquilla de
Bronce para
Jabón
Boquilla
de Alta
Presión
Manija de Control
de Presión Variable
Gatillo
33
LANDA VHP • 8.913-949.0 • Rev. 5/13
EQUIPO DE LAVADO A PRESIÓN
MANUAL DEL OPERADOR
MANTENIMIENTO Y SERVICIO
MANTENIMIENTO
PREVENTIVO
1. Revisar si la bomba de agua está lubricada apropiadamente.
2. Seguir las instrucciones para acondicionamiento
de invierno y prevenir daños por congelamiento de
la bomba y los serpentines.
3.Siempre neutralizar y limpiar después de usar
productos detergentes en el sistema.
4. Si el agua tiene alto contenido de minerales, usar
un ablandador de agua o eliminador de escamas
en el sistema, según sea necesario.
5. No permitir que líquidos ácidos, caústicos o abrasivos sean bombeados a través del sistema.
6. Siempre usar productos de limpieza de alta calidad
Landa.
7. Nunca hacer funcionar la bomba en seco por extensos períodos de tiempo.
8. Periódicamente, limpiar los depósitos de cal de los
serpentines según las instrucciones.
Se aconseja inspeccionar regularmente, el quemador en forma visual. Revisar el ingreso de aire para
asegurar que no esté atascado o bloqueado. Limpiar
todos los derrames de aceite y mantener la máquina
limpia y seca.
Las áreas alrededor de la lavadora Landa deberán
mantenerse limpias y libres de materiales combustibles, gasolina y otros líquidos inflamables.
El flujo de combustión y aire de ventilación al quemador no deben ser obstruídos o bloqueados de ninguna
manera.
MANTENIMIENTO Y SERVICIO
Válvulas de Descarga:
Las válvulas de descarga liberan la presión en la línea
cuando la pistola de rociado está cerrada. La válvulas
de descarga son programadas y verificadas antes
de salir de fábrica. Ocasionalmente, deben regularse
para mantener la presión correcta. (Ver la sección del
manual sobre válvulas de descarga para el procedimiento correcto de regulación de la válvula.)
Procedimiento de Acondicionamiento
para el Invierno:
El daño debido al congelamiento no está cubierto por
la garantía. Respetar los siguientes procedimientos
para el clima frío siempre que la lavadora deba almacenarse u operarse a la intemperie bajo condiciones
de congelamiento.
Durante los meses de invierno, cuando la temperatura
baja a menos de 32° F, se debe proteger la máquina
del congelamiento según sea necesario. Almacenar la
máquina en un ambiente con calefacción. Si ésto no
es posible, mezclar una solución 50/50 de anticongelante/agua en un depósito de 5 galones. Colocar una
sección corta de manguera de jardin en el depósito y
conectar a la máquina. Elevar el depósito y prender la
bomba para sifonear el anticongelante a la máquina.
Si se dispone de aire comprimido, puede instalarse
un accesorio de aire al conector de entrada y todo el
agua será evacuada fuera del sistema.
Termostato de Control de Agua Caliente:
Para seguridad, cada unidad está equipada con un
interruptor de control de temperatura. Si la temperatura
del agua excede la temperatura de operación, el control
apagará el quemador hasta que el agua se enfríe.
Bombas:
Usar solamente aceite no-detergente SAE 20/30.
Cambiar el aceite después de las primeras 50 horas
de uso. Luego, cambiar el aceite cada tres meses o
en intervalos de 500 horas. El nivel de aceite debe
ser revisado usando la varilla de medir ubicada en la
bomba o el punto rojo visible a través de la ventana del
calibrador. El aceite debe mantenerse en ése nivel.
Limpieza de Serpentines:
En áreas de agua alcalina, los depósitos de cal pueden
acumularse en los serpentines rápidamente. Estos
depósitos se incrementarán con la alta temperatura
generada en los serpentines. La mejor prevención para
la sedimentación es usar productos de limpieza de alta
calidad. En áreas donde el agua alcalina es un problema,
el uso regular de Polvo eliminador de cal Landa (parte
#9-028008) limpiará la cal y otros sedimentos antes
que obstruyan el serpentín.
Eliminador de cal de Serpentines:
Se recomienda un lavado periódico de los serpentines.
1. Llenar un depósito con 4 galones de agua y luego
añadir 1 libra de polvo desincrustante. Mezclar
completamente.
2. Retirar la varilla de la pistola y colocar la pistola en
un depósito. Asegurar que el gatillo de la pistola
esté en posición abierta.
3.Unir una sección corta (3-5 pies) de manguera
de jardin a la máquina para sifonear la solución
hacia un depósito elevado. Encender la bomba
para que la solución sea bombeada a través de
los serpentines de regreso al depósito. La solución
deberá circular por 2-4 horas.
34
LANDA VHP • 8.913-949.0 • Rev. 5/13
4. Después de hacer circular la solución, lavar todo
el sistema con agua fresca. Reinstalar la varilla en
la pistola.
Remoción de Hollín del Serpentín de
Calentamiento:
Durante el proceso de calentamiento pueden producirse residuos de combustible en forma de hollín
entre los serpentines de calentamiento, bloquear el
flujo de aire y afectar la combustión del quemador.
Cuando se observe hollín, debe limpiarse después de
seguir los pasos para desmontar el serpentín.
PRECAUCION: El serpentín pesa casi 80 libras.
Usar técnicas de levantamiento apropiadas.
4. Limpiar, reparar y reemplazar el serpentín siguiendo los pasos anteriores pero a la inversa.
Válvula de Alivio de Presión:
Cada unidad está equipada con una válvula de alivio
de presión para descargar la presión del sistema cuando se detectan presiones de operación más altas
de lo normal. Las altas presiones inusitadas provienen
de algún objeto que obstruye la boquilla de rociado.
Este problema se puede remediar fácilmente al retirar
la obstrucción. Si la presión de operación de la unidad
es normal y la válvula de alivio sigue con fugas, reparar
o reemplazar la válvula.
Capacidad del Cilindro de Gas Propano:
Una importante consideración con los sistemas de gas
propano, es la capacidad del cilindro de suministro en
relación a las necesidades del quemador. El quemador opera con gas propano del cilindro, el líquido del
cilindro ebulle para mantener la presión del gas. Este
proceso de ebullición enfría el líquido y, en una situación de demanda continua y exigente, la temperatura
del líquido puede disminuir a un punto que no puede
suministrar gas tan rápido como se requiere. En este
caso, podría ser necesario calentar el Cilindro de Gas
Propano rociando agua caliente que no exceda 120°
F, sobre el cilindro frío o al colocar dos botellas de gas
propano juntas para incrementar la capacidad total de
vaporización. Se recomienda usar una botella de gas
propano de 30 libras de capacidad en la unidad.
ADVERTENCIA: Algunos productos detergentes
pueden ser dañinos cuando se los inhala o ingiere, causar náuseas, desmayo o envenenamiento
agudo. Los elementos dañinos pueden causar
daño a la propiedad o lesiones graves.
El conjunto de inyectores para productos detergentes
de Landa se puede utilizar para hacer sifón y mezclar
los detergentes.
1. Apague el motor y cierre la entrada de agua. Antes
de acoplar el inyector de productos detergentes,
abra la pistola de rociado para aliviar la presión.
2. Para acoplar el inyector de productos detergentes
entre la unidad de lavado a presión y la manguera
de alta presión, tire del cuello del acoplador de
conexión rápida del inyector hacia atrás y coloque
el manguito de unión de descarga. La flecha de la
válvula de inyección debe apuntar en la dirección
del flujo.
3. Conecte la manguera de descarga de presión al
manguito de unión de inyección con el acoplador
de conexión rápida. Empuje el cuello del acoplador
hacia el manguito de unión.
4. Haga arrancar la unidad tal como se describe en
las Instrucciones para operar la unidad.
5.Coloque el tubo de aspiración para el producto
detergente en el recipiente de la solución detergente.
6.Instale la boquilla para detergente en el acople
rápido.
7. Abra la pistola a gatillo. La proporción de agua y
del producto detergente es de aproximadamente
15 a 1.
8. Para limpiar, coloque el tubo para el producto
detergente en un recipiente con agua limpia y
siga los pasos 5 y 7 para evitar que los depósitos
detergentes dañen el inyector.
9. Si la unidad cuenta con una extensión de presión
variable; para limpiar, alivie la presión haciendo
girar la manija para el control de presión en sentido
contrario a las agujas del reloj. Esto dirige el flujo
de agua a través de la boquilla de jabón y permite
que el inyector del producto detergente succione
el jabón. Para enjuagar con agua a alta presión,
simplemente gire la manija de control en la dirección de las agujas del reloj.
NOTA: El inyector para los productos detergentes
no puede hacer sifón cuando la manija de control,
de la extensión de presión variable, se encuentra
en posición de alta presión.
MANUAL DEL OPERADOR
1.Retirar el ensamble del tanque destornillando
los tres tornillos Tek y levantando el cabezal del
tanque.
2. Retirar los dos niples de la tubería y los accesorios
correspondientes.
3. Levantar el serpentín fuera de la envoltura exterior.
USO DEL INYECTOR DE
PRODUCTOS detergenteS
EQUIPO DE LAVADO A PRESIÓN
MANTENIMIENTO Y SERVICIO
35
LANDA VHP • 8.913-949.0 • Rev. 5/13
MANUAL DEL OPERADOR
EQUIPO DE LAVADO A PRESIÓN
identificacion de componentes
Inyector
Detergente
Disco de Alta
Presión
Colgador de
Manguera de
Alta Presión
Acoplamiento
Rápido
Niple de
Descarga
Interruptor de
Resorte de
Límite Alto
Manguera de
Suministro de
Agua (no se
incluye)
Boquilla de
Bronce para
Jabón
Colgador
de Varilla
Interruptor
de Bomba &
Quemador
Sostén de
la Varilla
Manguera
de Gas
Propano
Tanque
de Gas
Propano
(no se
incluye)
GFCI
Manguera
de Alta
Presión
Gatillo
Pistola de
Rociado
Boquilla de Alta
Presión
Manija de Control
de Presión Variable
Varilla de Presión
Variable
36
LANDA VHP • 8.913-949.0 • Rev. 5/13
ESTA GARANTÍA NO CUBRE:
Esta garantía no cubre los siguientes artículos:
1. Artículos que tienen un desgaste normal, como ser boquillas, pistolas, mangueras de descarga, extensiónes,
acopladores de conexión rápida, sellos, filtros, juntas, anillos en “O”, empaquetados, pistones, montaje de válvulas,
filtros de malla, correas, cepillos, etc.
2. Daño o malfuncionamiento debido a accidentes, abuso, modificaciones, alteraciones, instalación inapropiada,
servicio inapropiado, incumplimiento de las instrucciones de mantenimiento del fabricante o uso del equipo con
otros fines que no se adhieran a las especificaciones contenidas en el Manual del Operador.
3. Daño a causa de heladas, deterioro debido a productos químicos, acumulación de escamas, oxidación, corrosión
o expansión térmica.
4. Daño a los componentes debido a fluctuaciones en el suministro eléctrico o ala fuente de agua.
5. Servicio de mantenimiento normal, incluso los ajustes, limpieza del sistema de combustible y de obstrucciones.
6. Transporte al centro de servicios, cargos por mano de obra en planta o daño ocurrido durante el flete.
MANUAL DEL OPERADOR
QUÉ CUBRE ESTA GARANTÍA
LANDA garantiza al primer comprador que todos los equipos LANDA de lavado a presión están libres de defectos de
materiales y de fabricación durante el uso normal de la unidad y durante el tiempo que se indica más abajo. Esta Garantía
Limitada está sujeta a las exclusiones que se muestran a continuación. Dicha garantía entra en vigencia a partir de la fecha
de la compra del equipo y se aplica únicamente a los componentes originales. Cualquier parte que se reemplace durante
el período cubierto por esta garantía estará comprendida en el período de garantía restante para dicha parte.
GARANTÍA DE SIETE AÑOS PARA LAS PARTES Y DE UN AÑO PARA LA MANO DE OBRA:
Esta garantía cubre los componentes fabricados por Landa, como por ejemplo bastidores, manijas, envoltura de bobinas,
tanques con flotador, tanques para combustible, cubiertas de correas y bobinas. Los componentes internos relacionados
con el aceite de las bombas marca bombas propietarias tienen una garantía de 7 años. Las bombas con la marca General,
AR, Liberty, Comet y los bombas que “swash” o “wobble-plate” tienen una garantía de un año.
GARANTÍA DE UN AÑO PARA LAS PARTES Y DE UN AÑO PARA LA MANO DE OBRA:
El resto de los componentes, sin incluir el desgaste normal de los artículos que se describen abajo, estará cubierto por el
período que especifique su fabricante original, con un año. La garantía para la mano de obra que se aplica a estas partes
será de un año, sin perjuicio de la duración de la garantía del fabricante del componente original.
GARANTÍA SUMINISTRADA POR OTROS FABRICANTES:
Los motores, generadores y máquinas están cubiertos por la garantía de sus fabricantes. Los centros de servicios locales
autorizados por sus fabricantes prestan el servicio de mantenimiento y reparación de dichas unidades. LANDA no puede
proporcionar garantía alguna para estos artículos.
EQUIPO DE LAVADO A PRESIÓN
GARANTÍA DE LANDA PARA SUS PRODUCTOS
EQUIPOS DE LAVADO A PRESIÓN
QUÉ DEBE HACER PARA OBTENER EL SERVICIO DE LA GARANTÍA
A pesar de no ser necesario para el servicio de garantía, le solicitamos que registre su unidad para el lavado a presión.
Para ello, llene la tarjeta de registro y envíela a vuelta de correo. Para obtener el servicio de LANDA de la garantía, debe
hacer llegar el producto a un Distribuidor de LANDA autorizado, con flete prepago, acompañado del comprobante de la
compra, dentro del período prescrito por la garantía. En caso de que el producto esté instalado de forma permanente,
deberá notificar el defecto a su Distribuidor Autorizado de LANDA. El distribuidor Autorizado de LANDA presentará un
reclamo a Landa la cual deberá verificar el defecto. En la mayoría de los casos, deberá enviar la parte a LANDA con flete
prepago junto con el reclamo. Para el servicio de la garantía de los componentes garantizados por otros fabricantes, su
Distribuidor Autorizado de LANDA le ayudará a obtener el servicio que necesite de estos fabricantes por medio de sus
centros locales de servicio autorizado.
LIMITACIÓN DE LA RESPONSABILIDAD
LANDA especificamente renuncia a la responsabilidad de todo daño y perjuicio especial, incidental, o consecuencial. La
responsabilidad de LANDA con respecto a todo reclamo de cualquier índole, no superará, bajo circunstancia alguna, el
precio de compra del producto en cuestión. LANDA ha puesto todo su empeño para asegurarse de que las ilustraciones
y especificaciones son las que corresponden; no obstante, estas no implican la garantía de comerciabilidad o de aptitud
para un fin en particular o que el producto sea un fiel reflejo de las ilustraciones y especificaciones. LA GARANTÍA
CONTENIDA EN LA PRESENTE REEMPLAZA A CUALQUIER OTRA GARANTÍA, SEA EXPRESA, IMPLÍCITA, INCLUSO
TODA GARANTÍA IMPLÍCITADE APTITUD PARA UN FIN EN PARTICULAR. LANDA no autoriza a terceros, incluso a los
Distribuidores Autorizados de LANDA , a efectuar manifestación o promesa alguna en nombre de LANDA ni a modificar los
términos, condiciones o limitaciones en modo alguno. Es responsabilidad del Comprador asegurarse de que la instalación y
el uso de los productos LANDA se realice de acuerdo con los códigos locales. Bien que Landa intenta asegurarse de que
sus productos cumplan con los códigos nacionales, no se responsabiliza por el procedimiento de utilización del producto
ni por su instalación por parte del Comprador.
37
LANDA VHP • 8.913-949.0 • Rev. 5/13
Form #8.913-949.0 • Revised 5/13 • Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising