Tektronix MTM400A Technical Reference
Tektronix MTM400A is an advanced MPEG Transport Stream monitor designed to provide comprehensive analysis of video and audio content, ensuring the highest quality of service for digital TV and video streaming applications. With its ability to monitor multiple transport streams simultaneously, it offers real-time monitoring of key parameters, enabling broadcasters and network operators to quickly identify and resolve issues affecting the quality of their services.
Annonce
Annonce
Technical Reference
MTM400A
MPEG Transport Stream Monitor
Specifications and Performance Verification
071-2496-00
This document applies to firmware versions 3.0
and above.
www.tektronix.com
Copyright
©
Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
H
In North America, call 1-800-833-9200.
H Worldwide, visit www.tektronix.com to find contacts in your area.
Table of Contents
General Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications
Electrical, Hardware, and Signal Specifications . . . . . . . . . . . . . . . . . . . . . . . .
Power Source Characteristics
Environmental Characteristics
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mechanical (Physical) Characteristics
Certifications and Compliances
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performance Verification
Requirements
Procedure
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v vii vii
1--1
1--15
1--16
1--16
1--17
2--1
2--1
MTM400A Specifications and Performance Verification i
Table of Contents
List of Figures
Figure 2--1: MTM400A monitor RUI display . . . . . . . . . . . . . . . . . . .
2--3 ii
List of Tables
Table i: Product documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1--1: Remote User Interface (RUI) platform characteristics
Table 1--2: TS processor card - system timing clock . . . . . . . . . . . . .
.
Table 1--3: TS processor card - ASI interface . . . . . . . . . . . . . . . . . .
Table 1--4: TS processor card - SMPTE310M interface . . . . . . . . . .
Table 1--5: TS processor card - alarm connector
Table 1--6: TS processor card - alarms
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
Table 1--7: TS processor card - LTC connector . . . . . . . . . . . . . . . . .
Table 1--8: TS processor card - Ethernet RJ-45 connector . . . . . . . .
Table 1--9: QAM Annex A interface card characteristics
Table 1--10: QAM Annex B2 interface card characteristics
. . . . . . . . .
. . . . . . .
Table 1--11: QAM Annex B2 measurements . . . . . . . . . . . . . . . . . . . .
Table 1--12: QAM Annex C interface card characteristics . . . . . . . .
Table 1--13: 8PSK/QPSK interface card characteristics with
8PSK input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1--14: 8PSK/QPSK interface card characteristics with
QPSK input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1--15: 8PSK and QPSK measurements . . . . . . . . . . . . . . . . . . .
Table 1--16: 8VSB interface card characteristics . . . . . . . . . . . . . . . .
Table 1--17: 8VSB measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1--18: COFDM interface card characteristics . . . . . . . . . . . . .
Table 1--19: COFDM measurements . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1--20: GigE interface card - general characteristics . . . . . . . .
Table 1--21: GigE interface card - Ethernet electrical port
Table 1--22: GigE interface card - Ethernet Optical port
. . . . . . .
. . . . . . . . .
Table 1--23: GigE interface card - ASI input . . . . . . . . . . . . . . . . . . .
vii
1--4
1--4
1--5
1--5
1--1
1--1
1--2
1--2
1--3
1--4
1--6
1--6
1--7
1--7
1--8
1--8
1--9
1--10
1--11
1--12
1--12
1--13
1--14
MTM400A Specifications and Performance Verification
Table of Contents
Table 1--24: GigE interface card - ASI output (active loop-through of ASI/SMPTE input or TS from GigE interface card) . . . . . . .
Table 1--25: GigE interface card - SMPTE310M input
(loop-through to ASI output) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1--26: AC power source characteristics . . . . . . . . . . . . . . . . . . .
Table 1--27: Transport stream card batteries
Table 1--28: Environmental characteristics
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
Table 1--29: Mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . .
Table 1--30: Certifications and compliances . . . . . . . . . . . . . . . . . . . .
Table 1--31: Environmental limits and use classification for safety certification compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1--14
1--14
1--15
1--15
1--16
1--16
1--17
1--19
MTM400A Specifications and Performance Verification iii
Table of Contents iv MTM400A Specifications and Performance Verification
General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
To Avoid Fire or
Personal Injury
Use Proper Power Cord.
Use only the power cord specified for this product and certified for the country of use.
Ground the Product.
This product is grounded through the grounding conductor of the power cord. To avoid electric shock, the grounding conductor must be connected to earth ground. Before making connections to the input or output terminals of the product, ensure that the product is properly grounded.
Ground Equipment Connected to the Product.
Ensure that any equipment connected to this product is grounded and at the same potential.
Observe All Terminal Ratings.
To avoid fire or shock hazard, observe all ratings and markings on the product. Consult the product manual for further ratings information before making connections to the product.
The inputs are not rated for connection to mains or Category II, III, or IV circuits.
Power Disconnect.
The power cord disconnects the product from the power source. Do not block the power cord; it must remain accessible to the user at all times.
Do Not Operate Without Covers.
Do not operate this product with covers or panels removed.
Do Not Operate With Suspected Failures.
If you suspect there is damage to this product, have it inspected by qualified service personnel.
Avoid Exposed Circuitry.
Do not touch exposed connections and components when power is present.
Use Proper Fuse.
Use only the fuse type and rating specified for this product.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Provide Proper Ventilation.
Refer to the manual’s installation instructions for details on installing the product so it has proper ventilation.
MTM400A Specifications and Performance Verification v
General Safety Summary
Terms in this Manual
These terms may appear in this manual:
WARNING.
Warning statements identify conditions or practices that could result in injury or loss of life.
CAUTION.
Caution statements identify conditions or practices that could result in damage to this product or other property.
Symbols and Terms on the Product
These terms may appear on the product:
H
DANGER indicates an injury hazard immediately accessible as you read the marking.
H
WARNING indicates an injury hazard not immediately accessible as you read the marking.
H
CAUTION indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
CAUTION
Refer to Manual
Protective Ground
(Earth) Terminal vi MTM400A Specifications and Performance Verification
Preface
This manual contains the following information about the MTM400A MPEG
Transport Stream Monitor:
H
Specifications lists the electrical, physical, and environmental specifications of the MTM400A monitor.
H
Performance Verification contains a procedure to verify that the MTM400A monitor is operating normally.
Product Documentation
Table i lists the product documentation supporting the MTM400A monitor.
Table i: Product documentation
Item (Tektronix part number)
Quick Start User Manual
(071-2492-xx English,
071-2493-xx Japanese)
RUI v3.0 Upgrade Technical
Reference
(071-2505-xx)
Release Notes
(071-2494-xx)
Purpose
Provides installation and high-level operational overviews
Describes the remote user interface (RUI) changes introduced with the MTM400A monitor
Describes late breaking product information and operational issues
Location
+
+
+
+
+
+
Technical Reference
(071-2495-xx)
Provides in-depth operating information
(this manual)
Specifications and Performance
Verification Technical Reference
(071-2496-xx)
Test Parameter and Configuration
File Technical Reference
(071-2497-xx)
Programmer Manual
(071-2498-xx)
Provides complete product specifications and a procedure for verifying the operation of the instrument
Provides information about using test parameters and configuration files
Provides information about remote command syntax
Declassification and Security Instructions
(071-2499-xx)
Provides instructions for removing your proprietary information from the instrument
+
+
MTM400A Specifications and Performance Verification vii
Preface
Table i: Product documentation (Cont.)
Item (Tektronix part number)
Firmware Upgrade Instructions
(075-0972-xx)
Purpose
Provides instructions for upgrading the product firmware
Hardware Upgrade Instructions
(075-0973-xx)
Provides instructions for installing the optional hardware interface cards
Location
+
Key:
Printed document
MTM400A product documentation CD - PDF format
Tektronix Web site - PDF format viii MTM400A Specifications and Performance Verification
Specifications
Specifications
This section lists the electrical, environmental, and physical specifications of the
MTM400A monitor. All specifications are guaranteed unless labeled typical.
Typical specifications are provided for your convenience and are not guaranteed.
Electrical characteristics apply to test systems operating within the environmental conditions.
Electrical, Hardware, and Signal Specifications
Table 1- 1: Remote User Interface (RUI) platform characteristics
Characteristic
Minimum Specification
Operating System
Disk Space
Ethernet
Installed Software
RAM
CD-ROM Drive
Display
Description
1.2 GHz Intel Pentium Processor (Preferred: 2 GHz)
Microsoft Windows operating systems Windows 2000, Windows XP, and
Windows Vista (Recommended: Windows XP Pro)
2 GB free disk space
10/100-base T
Microsoft Internet Explorer, Version 7.0 minimum;
Sun Java Runtime Environment Version 6 Update 3 minimum (1.6.0_03)
1 GB
8x
1024 x 768 pixel video monitor with 16 available colors
Table 1- 2: TS processor card - system timing clock
Characteristic
PCR Offset Measurement Accuracy
System Timing Clock Drift
Description
2.0 ppm
1.0 ppm per year (maximum)
MTM400A Specifications and Performance Verification 1- 1
Specifications
Table 1- 3: TS processor card - ASI interface
Characteristic
ASI Input
Connector
Transport Stream Rate
Data Format
Signal Amplitude
Termination
Return Loss
Link Rate
ASI Output
Connector
Impedance
Transport Stream Rate
Signal Amplitude
Return Loss
Description
BNC
155 Mbps maximum, 250 kbps minimum
Accepts both Burst and Packet mode ASI format
2.0 V p-p maximum; 200 mV p-p minimum
75 Ω nominal, transformer coupled
10 dB min, 5 MHz to 270 MHz
270 Mbaud 100 ppm
(The Output is an active loop-through of the Input.)
BNC
75
Ω nominal, transformer coupled
Same as the ASI input
1.0 V p-p max, 600 mV p-p min, into a 75
Ω load
10 dB min at 270 MHz
Table 1- 4: TS processor card - SMPTE310M interface
Description Characteristic
SMPTE310M Input
Connector
Termination
Data Format
Input Bit Rate
Signal Amplitude
Return Loss
SMPTE310M Output
Connector
Output Bit Rate
Signal Amplitude
Output Impedance
Return Loss
BNC
75 Ω , transformer coupled
Bi-phase coded. Compliant with SMPTE310M
19,392,658.5 bps 2.8 ppm
2.0 V p-p maximum, 200 mV p-p minimum
10 dB min at 20 MHz
(The Output is an active loop-through of the Input.)
BNC
Same as the SMPTE310M input
600 mV min, 1.0 V max, into a 75 Ω load
75
Ω
, transformer coupled
10 dB min at 20 MHz
1- 2 MTM400A Specifications and Performance Verification
Table 1- 5: TS processor card - alarm connector
26-Pin, D-Type Connector Pin Function Description
RL5NC
DGND
DGND
TTL03
P5V
RL1CC
RL2CC
RL3CC
DGND
TTL02
DGND
P5V
RL1NC
RL2NC
RL3NC
RL4NC
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
Ground
TTL Output 2
Ground
5 V
Relay 1: Normally closed contact
Relay 2: Normally closed contact
Relay 3: Normally closed contact
Relay 4: Normally closed contact
Relay 5: Normally closed contact
Ground
Ground
TTL Output 3
5 V
Relay 1: Common contact
Relay 2: Common contact
Relay 3: Common contact
17
18
19
20
RL4CC
RL5CC
TTL01
DGND
Relay 4: Common contact
Relay 5: Common contact
TTL Output 1
Ground
21
22
23
24
25
TTLI1
RL1NO
RL2NO
RL3NO
RL4NO
TTL Input 1
Relay 1: Normally open contact
Relay 2: Normally open contact
Relay 3: Normally open contact
Relay 4: Normally open contact
26 RL5NO Relay 5: Normally open contact
Connector shell - Chassis ground
Specifications
MTM400A Specifications and Performance Verification 1- 3
Specifications
Table 1- 6: TS processor card - alarms
Characteristic
Alarm Relay
Number of relays
Maximum Switching Current
Maximum Switch Voltage
Contact Resistance
TTL Output Pins of the Alarms Output Connector
Output Type
Logic High Voltage
Logic Low Voltage
Maximum Switching Current
TTL Input Pins of the Alarms Output Connector
Maximum Input Voltage
Logic High Input Voltage
Logic Low Input Voltage
+5 V Output, Pins 4 and 13 of the Alarms Output Connector
Output Voltage
Maximum Output Current
Output Protection
Value
5
1 Amp
24 Vdc
100 milli-
Ω max
TTL open collector, requires external pull-up resistor
2.0 V min
0.8 V max, sinking 100 mA
100 mA
5.1 V
2.0 V min
0.8 V max
4.9 V min, 5.1 V max, no load
100 mA
Fused, self resetting
Table 1- 7: TS processor card - LTC connector
LTC 2-pin connector Pin
1
Function
IN+
Description
2 IN--
Connector shell - Chassis ground
Port Specification
Type
Input Voltage
Linear time code, SMPTE standard to ANSI/SMPTE 12M - 1995
2.0 V p-p differentially minimum
Table 1- 8: TS processor card - Ethernet RJ-45 connector
Characteristic
Connector
Description
10/100 Base-T; RJ-45
Use only good quality screened cable; Cat 6
1- 4 MTM400A Specifications and Performance Verification
Specifications
Table 1- 9: QAM Annex A interface card characteristics
Characteristic
Input Frequency Range
Modulation Format
Modulation Baud Rate, QAM A
Input Signal Level
Modulation Error Ratio (with equalizer)
Receiver Bandwidth, QAM A
Input Termination Impedance
Input Return Loss
Loop Through Power Gain
Loop Through Noise Figure
Loop Through Output Return Loss
Description
51 MHz to 858 MHz, 62.5 kHz steps
16 QAM, 64 QAM, 256 QAM (compliant with DVB-C ETS 300 421)
5.0 Mbaud/s minimum, 6.952 Mbaud/s maximum
--57 dBm (50 dBuV) to --27 dBm (80 dBuV), with a 16, 64, and 256 QAM input, providing five or fewer Transport Error Flags in 10 seconds, which corresponds to a post FEC rate of 1e
--8
38 dB min, with a 64 QAM input and 256 QAM input
8 MHz nominal
75 Ω nominal
6 dB min, 10 dB typical, 51 MHz to 858 MHz
1.5 dB to 4 dB typical, 51 MHz to 858 MHz typical
8 dB typical
Greater than 10 dB typical
Table 1- 10: QAM Annex B2 interface card characteristics
Characteristic
Input Frequency Range
Input Signal Level
Modulation Format
Interleaving Mode
Modulation Baud Rate
Spectrum Polarity
Receiver Bandwidth, QAM B
Connector Type
Input Termination Impedance
Input Return Loss
Ultimate Modulation Error Ratio with Equalizer
Description
88 MHz to 858 MHz
--64 dBm to --19 dBm (45 dBuV to 90 dBuV relative to 75
Ω
)
(With either a 64 or 256 QAM input, there are five or fewer Transport Error Flags in 11 seconds, which corresponds to a post FEC rate of 1e
--8
)
≥ -55 dBm to ensure compliance to EN 55103-2 immunity
64QAM, 256QAM (compliant with ITU J-83 Annex B)
Level 1 and Level 2 interleaving support compliant with all ITU J-83 Annex B, excluding I, J = (128,7) and (128,8), and in 256 QAM excluding (8, 16) and
(16, 8)
64 QAM: 5.056941 Mbaud/s
256 QAM: 5.360537 Mbaud/s
Demodulates both Normal and Inverted IF Spectrum.
6 MHz nominal
F type
75
Ω nominal
5 dB typical
≥
37 dB with equalizer; typical
MTM400A Specifications and Performance Verification 1- 5
Specifications
Table 1- 11: QAM Annex B2 measurements
Characteristic
RF Lock
Input Level (Signal Strength) (Typical)
EVM (Error Vector Magnitude) (Typical)
MER (Modulation Error Ratio) with Equalizer
(Typical)
SNR (Signal to Noise Ratio) (Typical)
BER (Bit Error Ratio)
TEF (Transport Error Flag)
Constellation
Description
RF lock is indicated by LED and Status
Range: --64 dBm to --19 dBm (45 dBuV to 90 dBuV relative to 75 Ω s)
Resolution: 1 dB
Accuracy: 3 dB
Display Range for 64 QAM: ≤ 1% to ≥ 5% rms
Display Range for 256 QAM: ≤ 1% to ≥ 2.5% rms
Resolution: 0.1%
Accuracy: 1%
Display Range:
64 QAM: 22 dB to 37 dB
256 QAM: 28 dB to 37 dB
Resolution: 0.1 dB
Accuracy: 1 dB for MER < 25 dB; 3 db for MER 25 dB to 34 dB
(measured at --30 dBm input)
Display Range:
64QAM: 22 dB to 37 dB
256QAM: 28 dB to 37 dB
Resolution: 1 dB
Accuracy: 1 dB for SNR < 25 dB; 3 db for SNR 25 dB to 34 dB
Pre-RS BER is displayed
Transport Error Flags (uncorrectable error count) in a 1 second window and 10 second window are displayed.
The RF constellation is displayed.
Table 1- 12: QAM Annex C interface card characteristics
Characteristic
Input Frequency Range
Modulation Format
Modulation Baud Rate, QAM C
Input Signal Level
Modulation Error Ratio (with equalizer)
Receiver Bandwidth, QAM C
Input Termination Impedance
Input Return Loss
Description
88 MHz to 858 MHz, 62.5 kHz steps
16 QAM, 64 QAM, 256 QAM (compliant with ITU J-83 Annex C)
4.5 Mbaud/s min; 5.5 Mbaud/s max
--57 dBm (50 dBuV) to --27 dBm(80 dBuV), with a 16, 64, and 256 QAM input, providing five or fewer Transport Error Flags in 12 seconds, which corresponds to a post FEC rate of 1e
--8
38 dB typical, with a 64 QAM input
6 MHz nominal
75
Ω nominal
6 dB min, 10 dB typical, 88 MHz to 858 MHz
1- 6 MTM400A Specifications and Performance Verification
Specifications
Table 1- 13: 8PSK/QPSK interface card characteristics with 8PSK input
Characteristic
Input Frequency Range
Input Signal Amplitude Range
Modulation Format
Modulated Baud Rate
Turbo Viterbi Values Supported
Turbo FEC
Connector Style
Input Termination Impedance
Input Return Loss
LNB Supply Voltage
LNB Supply Maximum Current
LNB 22 kHz Signaling Frequency
LNB 22 kHz Signaling Amplitude
Ultimate Modulation Error Ratio (with equalizer)
Description
950 MHz to 2150 MHz with 1 MHz step size
--60 dBm to --30 dBm for a CBER of <1e
--6
QPSK in accordance with ETSI EN 300 421
1 MBaud min, 30 MBaud max
2/3, 3/4 (2.05), 3/4 (2.1), 5/6, 8/9
Turbo code
F-style
75 Ω nominal
4 dB min, 950 MHz to 2050 MHz typical
Selectable; 13.0 V 1.5 V or 18.0 V 1.5 V, with 100 Ω , 5 watt resistor load
200 mA maximum
17.6 kHz min, 26.4 kHz max (22 kHz 20%)
600 mV p-p with 100
Ω load
26 dB with equalizer
Table 1- 14: 8PSK/QPSK interface card characteristics with QPSK input
Characteristic
Input Frequency Range
Input Signal Amplitude Range
Modulation Format
Modulated Baud Rate
Viterbi Values Supported
FEC
Turbo Viterbi Values Supported
Turbo FEC
Connector Style
Input Termination Impedance
Input Return Loss
LNB Supply Voltage
LNB Supply Maximum Current
LNB 22 kHz Signaling Frequency
LNB 22 kHz Signaling Amplitude
Ultimate Modulation Error Ratio (with equalizer)
Description
950 MHz to 2150 MHz with 1 MHz step size
--60 dBm to --30 dBm for a CBER of <1e
--6
QPSK in accordance with ETSI EN 300 421
1 MBaud min, 30 MBaud max
1/2, 2/3, 3/4, 5/6, 6/7, 7/8
In accordance with ETSI EN 300 421
1/2, 2/3, 3/4, 5/6, 7/8
Turbo code
F-style
75
Ω nominal
4 dB min, 950 MHz to 2050 MHz typical
Selectable; 13.0 V 1.5 V or 18.0 V 1.5 V, with 100
Ω
, 5 watt resistor load
200 mA maximum
17.6 kHz min, 26.4 kHz max (22 kHz 20%)
600 mV p-p with 100 Ω load
26 dB with equalizer
MTM400A Specifications and Performance Verification 1- 7
Specifications
Table 1- 15: 8PSK and QPSK measurements
Characteristic
RF Lock
Input Level (Signal Strength)
EVM (Error Vector Magnitude)
MER (Modulation Error Ratio) with Equalizer
SNR (Signal to Noise Ratio)
Pre Reed Solomon (RS) BER (Bit Error Rate)
Post RS BER and TEF (Transport Error Flag)
Constellation
Description
RF lock is indicated by LED and Status.
Range: --60 dBm to --30 dBm; Resolution: 1 dBm; Accuracy: 5 dBm; typical
Display Range:
≤
4.0% to
≥
30.0% rms; Resolution: 0.1%;
Accuracy: 20% of reading; typical
Display Range: 10 dB to 26 dB with equalizer; Resolution: 1 dB;
Accuracy: 2 dB for range 10 dB to 20 dB; typical
Display Range: 5 dB to 35 dB; Resolution: 1dB;
Accuracy: 2 dB for range from 5 dB to 30 dB; typical
Pre-RS BER is displayed.
Post Reed Solomon BER (TEF ratio), TEF rate, and number of Transport Error
Flags (TEF count) are displayed.
The RF constellation is displayed.
Table 1- 16: 8VSB interface card characteristics
Characteristic
Input Frequency Range
Input Signal Level
Modulation Format
Receiver Bandwidth
Input Termination Impedance
Connector Type
Input Return Loss
Description
54 MHz to 860 MHz, VHF/UHF channels 2 to 69 (to include low VHF frequencies)
--72 dBm to --6 dBm (--23 dBmV to + 43 dBmV)
≥ --60 dBm to ensure compliance to EN 55103-2 immunity
8VSB in accordance with ATSC A/53B.
6 MHz
75 Ω nominal
F type
5 dB minimum; typical
1- 8 MTM400A Specifications and Performance Verification
Specifications
Table 1- 17: 8VSB measurements
Characteristic
RF Lock
Input Level (Signal Strength)
(Typical)
EVM (Error Vector Magnitude)
(Typical)
Equivalent MER (Modulation Error Ratio) with
Equalizer (Typical)
SNR (Signal to Noise Ratio) (Typical)
BER
TEF (Transport Error Flag)
Constellation Diagram
Echo Profile (Typical)
Description
RF lock is indicated LED and Status
Display Range:
--72 dBm to --2 dBm relative to 75 Ω (--23 dBmV to +47 dBmV)
Resolution: 1dB
Accuracy: 3dB
Display Range:
≤
3.0% to
≥
12.5% rms
Resolution: 0.1%
Accuracy: 20% of reading
Display Range: 17 dB to 31 dB with Equalizer
Resolution: 0.1 dB
Accuracy: 1 dB for MER > 25 dB; 3 db for MER 25 dB to 31 dB
(Measured at --30 dBm input. For best MER accuracy, maintain the input signal level between --50 dBm and --15 dBm.)
Display Range: 15 dB to 35 dB
Resolution: 1 dB
Accuracy: 1 dB for SNR < 25 dB; 3 db for SNR 25 dB to 35 dB
Pre-RS BER, SER 1 second and 10 seconds windows values are displayed.
Transport Error Flags (uncorrectable error count) in a 1 second window and 10 second window are displayed.
The 8VSB constellation diagram is a display of I-data history with histograms
(the IQ constellation is not available). This is displayed as Symbol Distribution in the user interface.
Equalizer filter tap information is displayed.
Display Echo Level range: Normalized real tap values over the range of --1 to 1
Display Delay range: --6.7
μ s to 45.5
μ s
MTM400A Specifications and Performance Verification 1- 9
Specifications
Table 1- 18: COFDM interface card characteristics
Characteristic
Input Frequency Range
Input Signal Amplitude Range
Compliance
Tuning Resolution
Tuning Accuracy
Channel Bandwidth
Connector Style
Input Termination Impedance
Input Return Loss
Modulation Schemes Supported
Transmission Modes
Hierarchical modulation
Viterbi puncture rates
Guard Intervals
Spectrum Polarity
Ultimate Modulation Error Ratio, with Equalizer
Description
50 MHz to 858 MHz (to include low VHF)
The receiver delivers QEF (Quasi Error Free) operation over the following signal power ranges:
QPSK (4QAM): --85 dBm to --10 dBm (24 dBuV to 99 dBuV)
16QAM: --80 dBm to --10 dBm (29 dBuV to 99 dBuV)
64QAM: --72 dBm to --15 dBm (37 dBuV to 94 dBuV)
≥
--60dBm to ensure compliance to EN 55103-2 immunity
COFDM (DVB-T) receptions and demodulation, compliant with ETSI EN300-744,
2 K and 8 K transmission modes
166.7 kHz or smaller increments
Better than 50 ppm
7 MHz and 8 MHz (software selectable)
F-style
75
Ω nominal
7 dB minimum, 50 MHz to 858 MHz; typical
QPSK (4QAM), 16QAM, and 64QAM modulation
2 K carriers and 8 K carriers
All hierarchies will be supported, to include no hierarchy, and alpha = 1, 2 and 4.
1/2, 2/3, 3/4, 5/6, 7/8
1/32, 1/16, 1/8, 1/4
The receiver will operate with both inverted and normal spectral polarity.
≥ 37 dB with equalizer; typical
1- 10 MTM400A Specifications and Performance Verification
Specifications
Table 1- 19: COFDM measurements
Characteristic
Overall Receiver Lock Status
Transmission Coding Parameters
Input Level (Signal Strength) (Typical)
RF Carrier Offset
Carrier Power Distribution
SNR (Signal to Noise Ratio) (Typical)
EVM (Error Vector Magnitude) (Typical)
Description
Overall receiver lock status is indicated by an LED on the rear panel.
The receiver reports the current status of the following transmission parameters:
-- QPSK/16, QAM/64, QAM encoding
-- 2K/8K Transmission mode
-- Hierarchy status (hierarchy on/off, alpha value)
-- Viterbi puncture rate
-- Guard Interval Value
-- Gross bit rate in the channel
-- Spectrum polarity (inverted/non inverted)
Ranges, High Sensitivity mode:
QPSK (4QAM): --85 dBm to --10 dBm (24 dBuV to 99 dBuV)
16QAM: --80 dBm to --10 dBm (29 dBuV to 99 dBuV)
64QAM: --72 dBm to --13 dBm (37 dBuV to 96 dBuV)
Ranges, High Resolution mode:
QPSK (4QAM): --45 dBm to --10 dBm (64 dBuV to 99 dBuV)
16QAM: --45 dBm to --10 dBm (64 dBuV to 99 dBuV)
64QAM: --45 dBm to --13 dBm (64 dBuV to 96 dBuV)
Resolution: 1 dBm
Accuracy: 3 dBm
Accuracy: 50 ppm, of the tuned frequency; typical
The carrier-by-carrier signal-to-noise power ratio is displayed.
Channel Flatness in dB can be viewed from spectrum display.
Tilt in dB can be viewed from spectrum display.
Display Range:
6 dB to 40 dB for QPSK (4QAM):
11 dB to 40 dB for 16QAM
16 dB to 40 dB for 64QAM
Resolution: 1 dB
Accuracy: 1 dB to 30 dB SNR (measured at --30 dBm input in high resolution mode)
Display Range:
≤ 1% to ≥ 30% rms, for QPSK
≤
1% to
≥
20% rms, 16QAM
≤
1% to
≥
8.5% rms, 64QAM
Resolution: 0.1%
Accuracy: 1% (1 EVM unit), and additional 20% of reading
MTM400A Specifications and Performance Verification 1- 11
Specifications
Table 1- 19: COFDM measurements (Cont.)
Characteristic
MER (Modulation Error Ratio) with Equalizer
(Typical)
Channel Equalization Status
Constellation
BER
Post RS BER and TEF (Transport Error Flag)
Description
Both MER Peak and MER Average are displayed as measured across all carriers.
Display Range:
6 dB to 37 dB for QPSK (4QAM)
11 dB to 37 dB for 16QAM
16 dB to 37 dB for 64QAM
Resolution: 0.1 dB
Accuracy: 1 dB to 30 dB (Measured at --30 dBm input in High Resolution mode). For best MER accuracy, use High Resolution mode, and maintain the input signal level between --45 dBm and --15 dBm.
Channel estimate I and Q values for each carrier are displayed.
The RF constellation is displayed.
Pre-Viterbi BER and Pre Reed-Solomon BER values are displayed.
Post Reed Solomon BER (uncorrectable error count) and number of Transport
Error Flags are displayed.
Table 1- 20: GigE interface card - general characteristics
Characteristic
Ethernet Port
Transport stream rate over IP
Description
The Ethernet Interfaces supports 1000/100/10 Mbit/s data transmission. The Ethernet
Interface to the card will be an IEEE 802.3 compliant 10/100/1000 Ethernet interface supporting 10/100/1000BT, 1000BSX(multi-mode), and 1000BLX(single-mode).
Two Ethernet interfaces are available - a copper RJ-45 interface and an MSA (multisource agreement) compliant SFP (Small Form-factor Pluggable) connector. The SFP connector will provide for pluggable optical interfaces. Only one interface, either the copper or optical, will be active at a time for video over IP monitoring. The active interface will be selectable via software control.
250 Kbps to 155 Mbps; typical
Table 1- 21: GigE interface card - Ethernet electrical port
Characteristic
Standard
Connector Type
Data Format 10/100 Base T
Data Format 1000 Base T
Description
10/100/1000BASE-T IEEE 802.3
RJ-45
NRZ
Trellis encoded, PAM5 symbols full-duplex on 4-pair Cat-5 UTP per IEEE 802.3ab
1- 12 MTM400A Specifications and Performance Verification
Table 1- 22: GigE interface card - Ethernet Optical port
Characteristic Description
Ethernet Optical Transmitter General Characteristics
Optical Operating Mode
Connector Type
Standard
Data Format
Single Mode or Multimode
Duplex data link MSA compliant SFP connector
1000 BASE-X
NRZ
Ethernet Optical Transmitter - Single mode 1550nm Using Tek supplied SFP module
Output Power --2 dBm to +4 dBm; typical
Center Wavelength - 1550 nm
Total Jitter (Peak-to-Peak)
Extinction Ratio
1530 nm Min, 1550 nm Typ, 1570 nm Max; typical
< 170 ps
≥
9.0 dBm
Ethernet Optical Receiver - Single mode 1550nm Using Tek supplied SFP module
Optical Input Power --26 dBm to --3 dBm, BER 1 X 10
--12
; typical
Input Wavelength 1270 nm =
λ
= 1610 nm
Ethernet Optical Transmitter - Single mode 1310nm Using Tek supplied SFP module
Output Power --11 dBm to --3 dBm; typical
Center Wavelength - 1310 nm
Total Jitter (Peak-to-Peak)
Extinction Ratio
1270 nm Min, 1310 nm Typ, 1355 nm Max; typical
<
170 ps
≥ 9.0 dBm
Ethernet Optical Receiver - Single mode 1310nm Using Tek supplied SFP module
Optical Input Power --19 dBm to --3 dBm, BER 1 X 10
--12
; typical
Input Wavelength 1270 nm =
λ
= 1610 nm
Ethernet Optical Transmitter - Multimode 850nm Using Tek supplied SFP module
Output Power --9.5 dBm to --2 dBm; typical
Center Wavelength - 850 nm
Total Jitter (Peak-to-Peak)
Extinction Ratio
830 nm Min, 850 nm Typ, 860 nm Ma; typical
<
170 ps
≥ 9.0 dBm
Ethernet Optical Receiver - Multimode 850nm Using Tek supplied SFP module
Optical Input Power --17 dBm to 0 dBm, BER 1 X 10
--12
; typical
Input Wavelength 770 nm =
λ
= 860 nm
Specifications
MTM400A Specifications and Performance Verification 1- 13
Specifications
Table 1- 23: GigE interface card - ASI input
Characteristic
Connector
Transport Stream Rate
Data Format
Signal Amplitude
Termination
Return Loss
Link Rate
Description
BNC
250 Kbps to 155 Mbps; typical
Accepts both Burst and Packet mode ASI format
2.0 V p-p max; 200 mV pk to pk min
75
Ω nominal, transformer coupled
10 dB min, 5 MHz to 270 MHz
270 Mbaud
±
100 ppm
Table 1- 24: GigE interface card - ASI output (active loop-through of ASI/SMPTE input or TS from GigE interface card)
Characteristic
Connector
Impedance
Transport Stream Rate
Transport Stream Smoothing
Signal Amplitude
Return Loss
Description
BNC
75 Ω nominal, transformer coupled
250 Kbps to 155 Mbps max
Smoothing mechanism for the TS packets before retransmitting packets out on ASI port
600 mV pk to pk min, 1.0V
p-p max into a 75
Ω load
10 dB min at 270 MHz
Table 1- 25: GigE interface card - SMPTE310M input (loop-through to ASI output)
Characteristic
Connector
Termination
Data Format
Input Bit Rate
Signal Amplitude
Return Loss
Description
BNC
75
Ω nominal, transformer coupled
Bi-phase coded. Compliant with SMPTE310M
19,392,658.5 bps
±
2.8 ppm
2.0V
p-p max; 200 mV pk to pk min
10 dB min at 20 MHz
1- 14 MTM400A Specifications and Performance Verification
Specifications
Power Source Characteristics
Table 1- 26: AC power source characteristics
Characteristic
Source Voltage
Frequency Range
Power Consumption
Peak Inrush Current
Fuse Rating
Description
100 VAC to 240 VAC
50 Hz/60 Hz
1 A max
7.2 A peak at 240 VAC, 50 Hz
Mains fuse is 3.15 A, 250 V
(Not operator replaceable. Refer servicing to qualified service personnel.)
Table 1- 27: Transport stream card batteries
Characteristic
Quantity
Voltage
Capacity
Continuous Discharge (Maximum)
Overall Dimensions (Single cell)
Height
Width (Diameter)
Battery Type
Description
2 (In single carrier)
3 V
210 mAh
3 mA
3.2 mm (0.13 in)
20 mm (0.79 in)
Tektronix part number: 146-0096-xx
MTM400A Specifications and Performance Verification 1- 15
Specifications
Environmental Characteristics
Table 1- 28: Environmental characteristics
Characteristic
Temperature
Operating
Non-operating
Humidity
Operating
Description
+5 ° C to +40 ° C
--10
°
C to +60
°
C
10% to 80% relative humidity up to 31
°
C
Above 31
°
C, decreasing linearly to 50% at 40
°
C
10% to 95% relative humidity, non-condensing Non-operating
Altitude
Operating
Non-operating
0 m to 3000 m (9800 ft)
0 m to 12000 m (40000 ft)
Mechanical (Physical) Characteristics
Table 1- 29: Mechanical characteristics
Characteristic
Classification
Overall Dimensions
Height
Width
Depth
Required Clearance
Weight
Packaged Dimensions
Height
Width
Depth
Weight (Packaged)
Description
Transportable platform also intended for 19-inch rack mounted applications, 1RU high.
44 mm (1.73 in) (1RU)
430 mm (17.13 in)
600 mm (23.62 in)
Top and bottom: 0 mm; Sides: Standard 19 in rack mount
6.0 kg (13.3 lbs); fully loaded
241 mm (9.5 in)
590 mm (23.1 in)
760 mm (30 in)
9 kg (19.7 lbs)
1- 16 MTM400A Specifications and Performance Verification
Specifications
Certifications and Compliances
Table 1- 30: Certifications and compliances
Category
EC Declaration of Conformity - EMC
Australia/New Zealand Declaration of
Conformity - EMC
FCC
EC Declaration of Conformity - Low Voltage
Standard or Description
Meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility.
Compliance was demonstrated to the following specifications as listed in the
Official Journal of the European Communities:
EN 55103 Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use
1
.
Environment E4 - controlled EMC environment
Part 1 Emission
EN 55022 Class A radiated and conducted emissions
EN 55103-1, Annex A Radiated magnetic field emissions
Part 2 Immunity
1
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-11
Electrostatic discharge immunity
RF electromagnetic field immunity
Electrical fast transient / burst immunity
Power line surge immunity
Conducted RF Immunity
Voltage dips and interruptions immunity
EN 55103-2, Annex A Radiated magnetic field immunity
EN 55103-2, Annex B Balanced ports common mode immunity
EN 61000-3-2 AC power line harmonic emissions
EN 61000-3-2 Voltage Changes, fluctuations and flicker
1
Refer to RF interface card specification for minimum RF input level required to ensure EMC immunity performance.
Complies with EMC provision of Radiocommunications Act per the following standard(s):
AS/NZS 2064.1/2 Class A limits for Industrial, Scientific, and Medical
Equipment: 1992
Radiated and conducted emissions do not exceed the levels specified in
FCC 47 CFR, Part 15, Subpart B, for Class A equipment.
Compliance was demonstrated to the following specification as listed in the
Official Journal of the European Union:
Low Voltage Directive 2006/95/EC
EN 61010--1:2001. Safety requirements for electrical equipment for measurement control and laboratory use.
UL61010B-1:2003 Standard for electrical measuring and test equipment.
U.S. Nationally Recognized Testing Laboratory
Listing
Canadian Certification CAN/CSA C22.2 No. 1010.1:1997 Particular requirements for electrical equipment for measurement, control, and laboratory use. Part 1.
MTM400A Specifications and Performance Verification 1- 17
Specifications
Table 1- 30: Certifications and compliances (Cont.)
Category
Additional Compliance
Installation (Overvoltage) Category Descriptions
Overvoltage Category
Pollution Degree Description
Pollution Degree
Standard or Description
IEC61010-12001 Safety requirements for electrical equipment for measurement, control, and laboratory use.
Terminals on this product may have different installation (overvoltage) category designations. The installation categories are:
CAT IV For measurements performed at the source of low--voltage installation.
CAT III For measurements performed in the building installation.
CAT II For measurements performed on circuits directly connected to the low--voltage installation.
CAT I For measurements performed on circuits not directly connected to
MAINS.
Overvoltage Category II (as defined in IEC61010-1)
A measure of the contaminates that could occur in the environment around and within a product. Typically the internal environment inside a product is considered to be the same as the external. Products should be used only in the environment for which they are rated.
Pollution Degree 1 No pollution or only dry, nonconductive pollution occurs.
Products in this category are generally encapsulated, hermetically sealed, or located in clean rooms.
Pollution Degree 2 Normally only dry, nonconductive pollution occurs.
Occasionally a temporary conductivity that is caused by condensation must be expected. This location is a typical office/home environment. Temporary condensation occurs only when the product is out of service.
Pollution Degree 3 Conductive pollution, or dry, nonconductive pollution that becomes conductive due to condensation. These are sheltered locations where neither temperature nor humidity is controlled. The area is protected from direct sunshine, rain, or direct wind.
Pollution Degree 4 Pollution that generates persistent conductivity through conductive dust, rain, or snow. Typical outdoor locations.
Pollution Degree 2 (as defined in IEC61010-1). Rated for indoor use only.
1- 18 MTM400A Specifications and Performance Verification
Specifications
Table 1- 31: Environmental limits and use classification for safety certification compliance
Category
Temperature, operating
Altitude (maximum operating)
Equipment Type
Safety Class
Source Voltage Range
Fuse Rating
Current Rating
Pollution Degree
Standard or Description
+5
°
C to +40
°
C
3000 meters
Test and measuring
Class 1 - grounded product
100 VAC to 240 VAC, 50 Hz/60 Hz, single phase
Mains fuse is 3.15 A, 250 V, Fast; Not operator replaceable. Refer servicing to qualified service personnel.
1 Amp
Pollution Degree 2 (as defined in IEC 61010-1) Note: Rated for indoor use only.
MTM400A Specifications and Performance Verification 1- 19
Specifications
1- 20 MTM400A Specifications and Performance Verification
Performance Verification
Performance Verification
To verify that the MTM400A monitor is operating correctly, perform the following procedure.
Requirements
The MTM400A monitor must be connected to a network and have a valid
IP address as described in the MTM400A Quick Start User Manual .
The client PC must satisfy the requirements listed in Table 1--1 on page 1--1.
Procedure
1.
Connect the MTM400A monitor to an Ethernet network.
2.
Power up the MTM400A monitor and wait for the instrument initialization to complete.
3.
On a client PC (connected to the same network and subnet mask as the
MTM400A monitor), launch the Microsoft Internet Explorer Web browser.
NOTE
. This procedure describes how to access the the MTM400A monitor RUI using the Microsoft Internet Explorer Web browser. The RUI can also be accessed using the Tektronix Web Monitoring Systems Manager (WebMSM). This is described in the WebMSM User Manual, Tektronix part number 071-1239-xx.
MTM400A Specifications and Performance Verification 2- 1
Performance Verification
4.
In the Web browser address bar, enter the network identity or the IP address of the MTM400A monitor, for example: http://TSMonitor01 or http://111.222.333.444.
5.
Press Enter . A Java applet is downloaded from the MTM400A monitor and launched. The file size is approximately 1.5 MB; the download time will depend on the network speed and traffic.
CAUTION.
The Java applet will not run unless a temp directory is properly configured on the PC. A temp directory is set up by default in the Windows XP operating system; previous operating systems may require operator action.
The Java applet will not run unless the Sun Java Virtual Machine is installed.
Type java -version at the command prompt to verify that it is installed and that the version is 1.6.0_03 or greater. If it is not installed, you can download the latest version from the Sun Web site, www.java.com\getjava.
If you have to update the Java version on the PC, you will need to restart this procedure at step 3.
6.
In the Connect to MTM Device dialog box, select the Login Type from the drop-down list, Administrator or User.
7.
Enter the password for the Login Type you selected in step 6. The default password for Administrator is tek; there is no default password for User.
8.
Click Connect to start the connection process.
9.
Read the End User License Agreement if it appears, and then click I Accept .
10.
When the MTM400A monitor RUI opens, click Device in the button bar to display the Device Information view (see Figure 2--1).
11.
In the Device Information view, verify that the Application Firmware
Version is 3.0 or greater.
12.
If the MTM400A monitor connects and presents the RUI, and displays the correct application firmware version in the Device Information window, then the instrument is operating normally.
2- 2 MTM400A Specifications and Performance Verification
Performance Verification
Figure 2- 1: MTM400A monitor RUI display
MTM400A Specifications and Performance Verification 2- 3
Performance Verification
2- 4 MTM400A Specifications and Performance Verification
Download
Offentligt link opdateret
Det offentlige link til din chat er blevet opdateret. You may view and manage your chat links after registration here.
Dokument offentligt link
Annonce