11° PMG Series
osewill Thank you for purchasing a Rosewill Power Supply.
Please read the instruction manual before use and retain for future reference.
INSTALLATION
If replacing an existing PSU in a system, you will first need to remove the old
PSU. Please proceed as follows:
1. Disconnect the AC power cord from your existing power supply unit.
2. Disconnect the power supply from all the components in the PC, make sure that all the
connectors are unplugged.
3. Remove the four screws from the rear of the case that hold the old power supply to the
chassis, and then remove the old power supply unit from case.
Installing the Power Supply:
1. Make sure the I/O switch of the PSU is at off “O” position.
2. Install the Power supply unit in the appropriated space in the PC case and secure it by
screwing the four screws into the rear of the power supply.
3. Connect the 20+4 pin main power cable to the motherboard 20+4 pin socket.
The detachable 4 pin section of the connector can be separated to support a 20 pin
connection or section together to support a 24 pin socket.
4. Connect the 4+4 PIN (8 PIN) power cable to the mainboard. If your mainboard supports only
4 PIN jack, connect only the right side of the connector to the mainboard.
Pin1 Pind
+12V CPU power connector Right
(EPS 8 Pin/4+4Pin) Pint Ping сом [а oF +12V DC
com || [GG] +12v oc coM |] {dE +12v DC
=) COM dal +12V DC Ll CoM |G] GIF +12v pc
Pin2 Pin4 com |G] GIA +12v pc
Pin4 Pin5
AS aa
5. If you are using a graphics card with a 6 PIN/8 PIN connector, please connect the respective
connector to the socket on the board.
If your graphics card supports more than one socket, please connect the respective
connector to the socket on board.
6. Connect the SATA or Peripheral 4 PIN Molex connectors to the hard disk or SSDs or optical
drive.
7. Connect any others internal components that require power to the appropriate connector.
8. Make sure all the cables are securely seated.
9. Connect the AC power cord into the back of the power supply and switch on I/O switch at
input “I” position.
10. Your PSU is now connected and ready.
[ELECTRONIC SPECIFICATIONS
AC Input
Model No. DC Output | +3.3V +5V +12V -12V +5VSB
Voltage | Current
Max Output | ¿gp 18A 45.7A 0.3A | 2.5A
Current
100V Max
PMGSSO [low | 744% | Combined 100W 548.4w | 3.6w | 12.5W
Wattage
Total Output 590W
AC Input
Model No. DC Output | +3.3V +5V +12V -12V +5VSB
Voltage | Current
Max Output | tea | 184 | 541A | 03A | 25A
Current
100V Max
PMG650 | oy | 24° | Combined 100W 649.2W | 3.6W | 12.5W
Wattage
Total Output 650W
AC Input
Model No. DC Output | +3.3V +5V +12V -12V +5VSB
Voltage | Current
Max Output | tea | 184 | 625A | 0.3A | 2.5А
Current
100V Max
PMG750 | doy | 24° | combined 100W 750W | 3.6W | 12.5w
Wattage
Total Output 750W
|CONNECTORS
PMG Series
Cable / | = 3
20+4 PIN 4+4 PIN 6+2 PIN S-ATA 4 PIN 4 PIN
Motherboard CPU PCI-E Connector Molex Floppy
Connector Connector Connector Connector Connector
PMG550 1 1 2 6 3 1
PMG650 1 1 4 8 4 1
PMG750 1 1 4 8 4 1
PRODUCT FEATURES
e 80 Plus Gold certified to deliver over 90% efficiency
e ATX 12V V2.3 ready, supports EPS 12V 2.92 and backwards compatible with ATX 12V 2.01
e Active Power Factor Correction (PFC) with PF value of 0.95
e Maximum Protection: Over-voltage protection, short circuit protection, over power protection
e Long lasting, ultra-quiet 135 mm fan
e Extra-long cables support full size gaming chassis
e Crossfire and SLl support
e MTBF > 100,000 hours at 80% load, ambient temperature at 25°C
[PACKAGE CONTENTS
e PMG Power Supply Unit x1
e Modular Cable Set x1
e Cable Bag x1
e Quick User Guide x 1
e AC Power Cord x1
e Cable Tie x3
e Mounting Screw x4
[SAFETY & WARNING
e Due to the high voltage inside the power supply, do not attempt to remove the cover of power
supply. The warranty will be void if the cover is removed.
e Do not insert any objects into the open ventilation or fan grill area of the power supply.
e Do not store the power supply in high humidity and high temperature environment,
e Do not plug or unplug the power cord with wet hand.
| TROUBLESHOOTING
If you installed the new power supply and the system is not working
properly, please check the following:
e Make sure the AC power cord is plugged correctly into PSU inlet socket and power switch is
at input “I” position.
e Make sure the wall socket, extension power cord, power strip or surge protector in use, fully
functional and wall power switch turned on.
e Make sure that all the connectors from power supply are correctly plugged into the
mainboard.
e Make sure there are no short circuits within the systems that could result from defective
hardware or misplaced connectors.
e lf your are not sure, take all parts out of the housing and only leave the mainboard inside
together with the power supply. Disconnect all plugs, check them and then connect
them again to the respective sockets.
КС Ms A E
Reset
Technical Support Information techsupport @ rosewill.com 1-800-575-9885
Please register your product at www.rosewill.com for complete warranty information and support for your product. PMG Series_A
">
