Headset with Bluetooth
®
Technology
Wireless
Instruction Manual i315
Please read this manual carefully before operating and save it for future reference.
Have a question? Please visit http://www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
USER SAFETY GUIDE
INSTRUCTIONS ON ENVIRONMENT PROTECTION
Do not dispose of this product in the usual household garbage at the end of its life cycle; bring it to a collection point for the recycling of electrical and electronic appliances.
This symbol on the product means the instructions for use or the packaging will inform about the methods of disposal. The materials are recyclable as mentioned in its marking. By recycling, material recycling, and other forms of re-utilization of old appliances, you make an important contribution to the protection of the environment. Please inquire at your local community administration for an authorized disposal location.
Important Safety Instructions
1. Read instructions – All safety and operating instructions should be read before the appliance is operated.
2. Retain instructions – The safety and operating instructions should be retained in a secure place for future reference.
3. Heed warnings – All warnings on the appliance and in the operating instructions should be observed.
4. Follow instructions – All operating and use instructions should be followed.
5. Water and moisture – The appliance should not be used near water (bathtub, kitchen sink, laundry tub, pool, etc.).
6. Heat – The appliance should be situated away from heat
- 1 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
USER SAFETY GUIDE
Important Safety Instructions-Continued
sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
7. Power sources – The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.
8. Cleaning – The appliance should be cleaned with a dry cloth.
9. Objects and liquids entry – Care should be taken so that objects do not fall and liquids are not spilled into the device’s openings.
10. Servicing – The user should not attempt to service the appliance beyond that described in the user's operating instructions. All other servicing should be referred to qualified service professional.
FCC Notice (USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Refer to 47 CFR Sec. 15.19.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
- 2 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
USER SAFETY GUIDE
FCC Notice (USA)-Continued
communications, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Refer to 47 CFR Sec.
15.21.
Industry Canada Notice to Canadian Users
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Refer to IC
RSS 210 Sec. 5.11. The term “IC” before the certification or registration number only means that the registration was performed based on a Declaration of Conformity and that
Industry Canada technical specifications were met. It does not imply that Industry Canada (IC) approved this equipment. Refer to Self-Marking 6(f) and RSP 100 Sec. 4.
- 3 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
USER SAFETY GUIDE
Additional Safety Instructions
• When not in use, keep your device in a safe place where it will not be bent or crushed.
• Keep this device away from children. Some small and detachable parts might be swallowed by children and result in harm to them.
About Electromagnetic Interference (EMI)
This device is designed and manufactured not to exceed the exposure limit for radio frequency energy, which is set by the
Federal Communications Commission of the U.S government.
The term “EMI” is short for the electromagnetic interference caused by the electromagnetic field generated by electronic devices. In fact, most electrical appliances and devices emit electric and magnetic fields, and most of modern electronic devices are susceptible to the EMI if they are inadequately shielded or designed.
• If you use any personal medical device, such as a pacemaker, please consult the manufacture of your medical device to determine if it is adequately shielded from EMI. Your physician might assist you in obtaining this information.
• Please turn off this device if you are instructed to do so, especially on an airplane or in a hospital.
• Please keep away from medical instruments in a hospital or medical unit while using this device.
- 4 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
USER SAFETY GUIDE
IMPORTANT NOTES ON HEARING
Your hearing is very important to you and to us. We strongly recommend you to follow the guideline below in order to prevent possible damage to or loss of hearing.
Hearing experts caution that listening to loud sounds can damage hearing over time. With continuous listening to loud sounds, hearing adapts and will give the impression that volume has reduced. What seems normal may, in fact, be harmful. To guard against this before hearing adapts, set the volume at a low level and slowly increase the volume level until sound can be heard comfortably and clearly without distortion. Damage to hearing is accumulative and is irreversible. Ringing or discomfort in the ears indicates that the volume is too loud. Once a comfortable listening level has been established, do not increase the volume level further.
CAUTION!
If you experience a ringing sound in your ear, lower the volume or discontinue the use of this product.
- 5 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
TABLE OF CONTENTS
GETTING STARTED
Introduction. …..………..……………………………………… 7
What’s Included in the Package…………………………..… 8
What is Bluetooth wireless technology? ............................. 8
Location of Controls…………………………………………… 9
Charging the Headset………………………………………… 10
Turning on the Headset………………………………………. 10
Turning off the Headset………………………………………. 10
Pairing the Headset using Bluetooth Wireless Technology. 11
OPERATING INSTRUCTIONS
Making a call…………………………………………………… 13
Answering a call……………………………………………… 14
Ending a call…………………………………………………… 14
Answering a Call while already on the Phone……………… 15
Rejecting an Incoming Call…………………………………… 15
Transferring Calls between Devices………………………… 15
Call Waiting (3-Way Calling)………………………………… 16
Adjusting the Volume / Mute Function……………………… 16
TROUBLESHOOTING GUIDE
Questions and answers about the product………………… 17
SPECIFICATIONS
Technical information about the product…………………… 17
- 6 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
GETTING STARTED
Headset with
Bluetooth
Wireless Technology
Thank you for purchasing the i315 from iLuv. This headset has been designed wireless mobile phone connection using
Bluetooth wireless technology. Please keep this manual in a safe place for future reference.
• Air-cushioned
• Answer mobile phone calls hands free
• Supports the headset (HSP), hands-free (HFP) profiles
• Standby time up to 260 hours
• Continuous listening time up to 8 hours
• Continuous talking time up to 10 hours
• Communication range up to 33ft
• Compliant wireless technology V2.0 and EDR
- 7 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
GETTING STARTED
What’s included in the package?
• Headset
• Charger
• Spare cushion
• Instruction
• Warranty
What is
Bluetooth
wireless technology?
Bluetooth wireless technology is a short-range wireless communication technology intended to replace the cables connecting electronic devices while maintaining the high level of security. With Bluetooth wireless technology, two devices can be connected at the same time without the need to face each other or the concern of interference from other wireless communication within its optimum range of 33 feet.
Through a process called “Pairing,” two or more devices with
Bluetooth wireless technology can interact with each other without interference from other wireless platforms nearby, including other Bluetooth wireless communications between unrelated devices.
- 8 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
GETTING STARTED
LOCATION OF CONTROLS
1
2
3
4
1. Ear hook
2. Indicator light
3. Volume control
4. Microphone
5
6
7
5. Charging port
6. Multi-function button
7. Air-cushioned ear
piece / speaker
- 9 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
GETTING STARTED
Charging the Headset
Fully charge the headset by connecting the charger to the mini-USB port on the top of the headset.
The red indicator will light up when charging.
Once fully charged, the red indicator will go out.
Turning on the Headset
Press and hold the Multi-function button for approximately five
(5) seconds until the blue indicator light begins flashing.
Note : The blue indicator will continuously flash when the power is on.
Turning off the Headset
Press and hold the Multi-function button for approximately five
(5) seconds until the red indicator flashes briefly.
Note : No light will flash when the power is off.
- 10 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
GETTING STARTED
Pairing the headset with mobile phones using
Bluetooth
wireless technology
1. With the power turned off, press and hold the Multi-function button for approximately seven (7) seconds.
2. Blue and Red lights will blink alternatively.
3. Set both the i315 and the mobile phone to SEARCH mode following the pairing instructions included with the phone , placing both units close together. Typically mobile phones have a Bluetooth menu from which SEARCH can be selected.
4. The mobile phone with Bluetooth wireless technology will identify the Headset.
5. Confirm with “yes,” or “ok.”
6. When asked for a passkey or PIN, enter
0000 (4 zeros) and press “yes,” or “ok.”
7. Phone and headset have successfully paired.
- 11 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
GETTING STARTED
Notes on Pairing
This headset will not be recognized by your mobile phone unless it is properly paired. The i315 cannot pair with mobile phones which are not equipped with Bluetooth wireless technology. To ensure that correct pairing is accomplished, it is important to follow both these instructions and those which accompany the corresponding mobile phone.
Wearing the Headset
The i315 can be worn on either the left of right ear.
Right ear
1. Place the ear hook over the right ear with earpiece in the ear.
2. For placement in the left ear, remove the ear hook as shown.
3. Flip the ear hook and reattach.
4. The i315 can now be worn comfortably on the left ear.
- 12 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
OPERATING INSTRUCTIONS
Making a Call
This headset must also be paired with your phone, enabled by
Bluetooth wireless technology in order to make a call.
1. Normal dialing: a. Dial the telephone number on your mobile phone. b. When the call connects, it will be heard through the headset.
2. Last number redial: After a call has been made, the number can be redialed by short-pressing the Multi-function button.
3. Voice dial function: If your mobile phone supports voice dialing, set up voice tags using the instructions for your phone. For the best connection with i315, pair and use this unit when establishing voice tags. a. Press the button for approximately two (2) seconds. b. Say the name of the person you wish to call. c. The number of the selected person will dial and be connected.
2 sec.
- 13 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
OPERATING INSTRUCTIONS
Answering a Call
Be certain the headset is properly paired with a mobile phone featuring Bluetooth wireless technology before answering a call.
1. An incoming phone call will be indicated by a ring. Press the
Multi-function button once to answer the call.
2. If the headset is off when there is an incoming call, press the
Multi-function button to turn on the headset and answer the call as usual.
Notes on Answering a Call
• When there is an incoming call, some phones might not ring when paired with i315, but there will be a beeping sound from the headset. Press the Multi-function button to answer the phone when you hear this beep.
• Similarly, some phones may not send an incoming call signal to the headset. Press the Multi-function button when the phone rings.
Ending a Call
There are several ways to end a phone call.
1. Press the button on the headset.
2. Press the key on the mobile phone.
3. A call will also end as the person on the other end hangs up.
- 14 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
OPERATING INSTRUCTIONS
Answering a call while already on the Phone
With the i315, it is possible to answer an incoming call while already on the phone.
1. There will be a sound inflection during the phone conversation. Press and hold the Multi-function button until there is a beep . The previous call will be placed on hold without disconnecting and the incoming call can be answered.
2. To return to the previous call, press the Multi-function button again until there is a beep sound.
Note: Your mobile phone with Bluetooth wireless technology must be paired with the i315 BEFORE these functions are attempted.
Rejecting an Incoming Call
When there is an incoming call, press and hold the Multifunction button for approximately two (2) seconds and release to reject the call.
Transferring Calls between Devices
1. To transfer a current call to your mobile phone when using the i315, press the Multi-function button for two (2) seconds.
The call will no longer be communicated through the i315.
Use your mobile phone as normal.
2. To transfer a current call to the i315 when using your mobile phone, press the Multi-function button for two (2) seconds.
The call will now be communicated through the i315.
- 15 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
OPERATING INSTRUCTIONS
Call Waiting (3-Way Calling)
If your mobile phone supports the Hands-Free Profile (HFP), you can use the Call Waiting (3-Way Calling) function on i315.
1. Press and hold the Volume Down ( T ) button for approximately four (4) seconds until three (3) short beeps are heard through the headset. This enables an incoming / waiting call to be picked up and ends the current call.
2. Press and hold the Volume Up ( S ) button for approximately four (4) seconds until three short beeps are heard through the headset. This enables an incoming / waiting call to be picked up while placing the current call on hold.
Adjusting the Volume / Mute Function
1. To adjust the volume, press the Volume Up ( S ) or Volume
Down ( T ) button.
2. To the microphone, press and hold the Volume
Down ( T ) button for approximately two (2) seconds. A melody will sound every ten (10) seconds while the microphone is muted.
3. To cancel the Mute function, press either the Volume Up ( S ) or Volume Down ( T ) button.
- 16 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
TROUBLESHOOTING GUIDE
1. The headset does not work with my mobile phone.
Be certain that your mobile phone is equipped with Bluetooth wireless technology. This headset will only work with such mobile phones. Additionally, your mobile phone must be paired with the headset BEFORE all other pairing.
2. There is interference on the headset with my phone.
The maximum distance for Bluetooth wireless communication is 33 feet (10 meters). When this distance is approached, background noise will increase. Also, a poor signal on the mobile phone may contribute to degradation the quality of sound as well.
3. There is no sound.
Ensure that both the mobile phone and the i315 are turned on, set up, and paired correctly. Be certain that the volume is turned up on both devices.
Specifications
•
•
•
•
•
•
Bluetooth spec. v2.0+EDR compliance
Headset (HSP) and Hands-free Profile (HFP) supported
Bluetooth Class ll
Typically 8 hrs Talk Time
Typically 260 hrs Stand-by Time (Approx. 11 days)
Rechargeable Lithium Polymer Battery
- 17 www.i-Luv.com
Headset w/ Bluetooth technology V10M10_IM_EN_04252007
- 18 www.i-Luv.com
TEL: 516-626-7188
FAX: 516-626-7105 website: www.i-Luv.com iLuv is a trademark of jWIN Electronics Corp. Features and specifications are subject to change without prior notification. iPod is a trademark of Apple
Computer, Inc. The Bluetooth word mark and logos are owned by Bluetooth
SIG, Inc. and any use of such marks by jWIN Electronics Corp. is under license. Mobile phone not included in this package.
© 2007 jWIN Electronics Corp. All rights reserved. No portion of this printed material or product enclosed herewith including design, shape and graphics, may be reproduced or transmitted in any form without the expressed written consent of jWIN Electronics Corp. by any means, electronic or mechanical, including photocopying, recording or the use of an information storage and retrieval system. Any unauthorized distribution or reproduction of this printed material or product, or any portion thereof, will be prosecuted to the fullest possible extent of the law.
Printed in China
