Gaggenau AH530790 Assembly Instructions

Add to my manuals
18 Pages

advertisement

Gaggenau AH530790 Assembly Instructions | Manualzz

Operating and assembly instructions

AH 530-790

AH 530-720

Extractor hood

AH 530-790

AH 530-720

Preface

Safety notes

1. Important notes

1.1 For your safety

1.2 Operating for the first time

1.3 About use

2. Features

3. Operation

4. Cleaning and care

5. Maintenance

6. Assembly instructions

6.1 Technical data

6.2 Installation

Page 3

Page 4-5

Page 4

Page 5

Page 5

Page 6

Page 7-9

Page 10-11

Page 12

Page13-17

Page 13

Page 14-17

1

Preface

With your new extractor hood, working in the kitchen will be even more fun.

The appliance offers you a number of advantages:

– A good extraction capacity with low noise values,

– a large number of control functions,

– optimum illumination of the cooking surface by a dimmable halogen light.

To ensure that you will be able to use this appliance in all its diversity, read through the operating and assembly instructions conscientiously before operating it for the first time . The instructions contain important notes on use, installation and maintenance of the appliance.

On the following page you will find important notes on safety and operation . These will serve to ensure your personal safety and the lasting value of your appliance.

You will find notes on Page 4 that you ought to observe before operating the appliance for the first time .

The chapters entitled “Features” and

“Operation” will tell you all the things your extractor hood is capable of doing and how the appliance is operated.

Tips and hints in the chapter entitled “Cleaning and care” will make sure that your appliance will stay operable and beautiful for a long time.

And now we wish you lots of fun with your new extractor hood.

2

Fig. 1

Safety notes

Read And Save These Instructions.

WARNING - TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

a.) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.

b.) Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

CAUTION:

FOR GENERAL VENTILATION USE ONLY. DO NOT

USE TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS AND VAPORS.

WARNING - TO REDUCE THE RISK OF INJURY

TO PERSONS IN THE EVENT OF A RANGE

TOP GREASE FIRE, OBSERVE THE

FOLLOWING:

a.) SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE

AND CALL THE FIRE DEPARTMENT.

b.) NEVER PICK UP A FLAMING PAN - You may be burned.

c.) DO NOT USE WATER, including wet dishcloth or towels - a violent steam explosion will result.

d.) Use an extinguisher ONLY if:

1. You know you have Class ABC extinguisher, and you already know how to operate it.

2. The fire is small and contained in the area where it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

WARNING - TO REDUCE THE RISK OF A

RANGE TOP GREASE FIRE.

a.) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

b.) Always turn hood ON when cooking at high heat or when cooking flaming foods.

c.) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

d.) Use proper pan size. Always use cookware appropriate for the size of the surface element.

3

4

1. Important notes

1.1 For your safety

– Damaged appliances must not be operated.

– The appliance must only be connected by an authorised specialist , paying attention to the relevant regulations of the power supply companies and the regional construction regulations.

Also observe the assembly instructions!

– Connecting cables must not come into contact with hot cooking surfaces.

– Do not operate the extractor hood without inserted lamps.

– Never operate the appliance without a grease filter.

– Hazardous or explosive substances and vapours must not be extracted!

– The user is responsible for expert use and the perfect condition of the appliance.

– Only ever operate the appliance under supervision.

– Caution!

Over-greased filters are a fire risk!

Only ever deep-fry under the extractor under constant supervision. Pay attention to cleaning the grease filter on a regular basis.

– Fire risk!

Do not flambé meals under the extractor hood!

– Operation of the extractor hood above a hearth for solid fuels (coal or wood etc.) is only partly permitted.

– Gas appliances may only be used under the extractor hood when pots and pans are placed on them!

– When using more than 3 gas-operated rings at the same time, please operate the extractor hood at level 2 or higher. This prevents a buildup of heat in the appliance.

– For safety reasons, do not place any heavy objects on the top of the appliance.

– Do not clean the appliance with a steam cleaning apparatus or with water pressure because this poses a risk of short-circuits .

– Isolate the appliance from the mains during every maintenance operation. To do this, actuate the corresponding fuse.

– Repairs must be carried out by authorised specialists, thus ensuring electrical safety.

– No warranty claims can be lodged in the event of damage caused by failure to observe these instructions.

– Adequate incoming air must be ensured if a wood, coal, gas or oil heater or an open hearth is operated in the same room as the one in which the hood is installed.

– Safe operation is possible whenever the partial vacuum in the place where the firing equipment is installed does not exceed 4 Pa (0.04 mbar).

This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/exhaust air wall boxes or other technical means.

– If the appliance is to be operated only with the window open (to ensure adequate incoming air), you can use the window switch .

A switch (normally open) is fitted on the window.

On the appliance, this switch is connected to the window switch terminal on the main electronics.

The appliance can now only be operated when the window is open.

Important: The window switch must only be connected by an authorised specialist.

Note: The light function works without restriction.

– After a power failure, the extactor will not go on again automatically. You can recommence operation by turning a knob or by pressing any key.

Technical modifications reserved.

1.2 Operating for the first time

Before operating the appliance for the first time, please pay attention to the following notes:

– The appliance must be installed and connected by a specialist before it is operated for the first time.

– The rating plate for this appliance is included with the instructions on a separate sheet. Store the rating plate in the same location as your operating and assembly instructions. You need the rating plate for possible damage and warranty cases.

– Conscientiously read through the operating and assembly instructions before operating the appliance for the first time.

– Remove the packaging from the appliance and dispose of it properly. Pay attention to the fact that there are accessories in the packaging.

Keep packaging elements out of the reach of children!

– Thoroughly clean the appliance before using it for the first time (see chapter entitled “Cleaning and care”).

– Before operating the appliance for the first time, check that the mains connection is in proper working order.

1.3 About use

– The appliance is intended solely for use in the household and must not be put to any other uses.

– In the event of malfunctions, first of all check the household fuses. If the problem has nothing to do with the power supply, please contact your specialist dealer or your local Gaggenau aftersales service.

5

2. Features

1

2

1 Outgoing air duct

2 Control panel

3 Grease filter

4 Lighting

Fig. 2

3 4

6

Fig. 3

Grease filter saturation display

Lighting

Run-on

Extraction level intensive

Extraction level 3

Extraction level 2

Extraction level 1

Motor off

Installation accessories:

Stainless steel-design ventilation duct:

LK 530-010 for ceiling heights of

7 ´´ 3 ´ ´ - 8 ´´ 6 ´ ´ / 2.20 - 2.66 m

LK 530-020 for ceiling heights of

8 ´´ 6 ´ ´ - 10 ´´ 1 ´ ´ / 2.66 - 3.15 m

Aluminium-design ventilation duct:

LK 530-011 for ceiling heights of

7 ´´ 3 ´ ´ - 8 ´´ 6 ´ ´ / 2.20 - 2.66 m

LK 530-021 for ceiling heights of

8 ´´ 6 ´ ´ - 10 ´´ 1 ´ ´ / 2.66 - 3.15 m

3. Operation

Fig. 4

Fig. 5 or or or

The AH 530-790 is 35 3 /

8

´ ´ / 90 cm wide, and the

AH 530-720 is 47 3 /

16

´ ´ / 120 cm wide. Operation of both extractor hoods is identical.

After they have been pressed, all functions selection keys except 0 (“Motor off”) are backlit in green.

Light

The lighting can be switched on or off, regardless of whether the wall extractor is in operation, by pressing the key (see Fig. 4).

When you briefly press the key, the lighting is increased up to the maximum level.

You can dim the lighting to the required level by keeping the key pressed.

Fan levels

Three fan speeds and one intensive speed are available (see Fig. 5). You set the fan level required for each respective cooking situation by pressing the function selector keys 1, 2, 3 or Int .

7

Fig. 6

Fig. 7

8

Fig.. 8

The Int key for the intensive level should be pressed when browning and frying in an open pan

(see Fig. 6).

If you have switched on the hood by selecting the intensive level, it will be switched off again automatically after 5 minutes.

If you press the Int key while the hood is running at fan level 1, 2 or 3 , the electronic control will switch back automatically to the previously selected fan level after 5 minutes (see Fig. 7).

If you would like to end the intensive level before the five minutes have elapsed, press the 0 key

(“Motor off”) or select a different level (see Fig. 8).

You can of course switch off the hood’s extraction function at any time by pressing the 0 key (“Motor off”).

Fig. 9

Fig. 11 or

Fig. 12 or or

Fig. 10 or or or or

Special functions:

Intensive time:

You can set the intensive level running time to 3, 5 or 10 minutes by simultaneously pressing the Int key and the 1, 2 or 3 key and you can store this setting (see Fig. 9). When delivered, the appliance is set to five minutes, i.e. the combination of the Int key and the key 2 .

Delayed shut-off:

Delayed shut-off is possible at any level. First press the required key 1, 2, 3 or Int and then press the key (see Fig. 10).

The delayed shut-off time for all levels is ten minutes. After these ten minutes, the ventilation switches off, but the lighting stays on.

Interval ventilation:

Interval ventilation is a special feature of this appliance which periodically activates the fan for five minutes every hour. You can activate this function by simultaneously pressing the 0 key and, depending on the required extraction capacity, the

1, 2 or 3 key (see Fig. 11).

This mode of operation is indicated by alternating illumination of the key together with the corresponding fan level indicator.

You can switch off interval ventilation by pressing the 0 key (see Fig. 12).

9

4. Cleaning and care

Fig. 13

Cleaning the grease filters

The grease filter saturation display F flashes after an operating time of 30 hours to indicate that you should clean the grease filter (see Fig. 3). The grease filter can of course be cleaned at any time, even if the grease filter saturation display should not start to flash.

The stainless steel grease filters can be removed easily for cleaning (see Fig. 13):

Grip the grease filter handle and push the slide towards the rear. Then pull the grease filter downwards out of the holder; repeat the operation for the other grease filters.

You can clean the stainless steel grease filters in a dishwasher at a maximum temperature of 150 °F /

65 °C, where it should be supported vertically to allow food or rinsing residues to drain off.

The inner parts of the housing should be wiped out with hot rinsing water when replacing the filters.

Note:

When cleaning the inside of the housing avoid protruding parts.

After having cleaned them, re-insert the grease filters in the hood in reverse order.

Important:

The handles of the grease filters must be visible after assembly.

Press the F key to set the elapsed hours counter to zero. Flashing of the indicating lamp goes off.

10

Fig. 14

Fig. 15

Cleaning the extractor hood

Clean the extractor hood and the aluminiumdesign ventilation ducts (LK 530-011/021) with a soft cloth and mild detergent solution only.

Clean the stainless-steel design ventilation ducts (LK 530-010/020) with mild detergent solution and apply stainless steel care agent to the metal surface using a soft cloth.

Cleaning the glass plates

Apply commercially available window cleaning agent with a soft, moist cloth. To facilitate cleaning, you can detach the glass plates as follows:

Detach the grease filters. Inside the extractor hood, you will find three openings on the upper side through which you can lift the glass plates singly with a blunt object (e.g. handle of a wooden spoon) to detach them with greater ease.

If they are extremely soiled, the glass plates can be cleaned in a dishwasher at a maximum temperature of 130 °F / 55 °C.

Note: When putting the glass trays back in place, make sure that you do not scratch the chimney.

Cleaning the aluminium panel

Clean the aluminium panel with a sponge and mild detergent solution only. Wipe with a soft, dry cloth.

Do not use any strong or caustic cleaning agents or brushes and abrasive cleaner to clean it. Do not use strongly alkaline cleaning agents (such as oven spray) because these are aggressive to the aluminium surface. Do not use any abrasive sponges either.

11

5. Maintenance

Fig. 16

The appliance must be disconnected from the power supply during all repair work.

If the appliance does not function correctly, check the fuses first.

If the power supply is functioning correctly, but your appliance still does not work, please contact your

Gaggenau dealer who will provide you with the address and telephone number of your nearest manufacturer’s authorized service agent or contact

Gaggenau USA on (800) 828-9165.

Specify the appliance type (see rating plate).

Repairs may only be carried out by authorised technicians , in order to guarantee the safety of the appliance.

Unauthorised tampering with the appliance will invalidate any warranty claims.

Only ever use original spare parts.

Lamp replacement

Caution: Disconnect the power supply before replacing lamps (switch off the fuse)!

Caution: Lamps may still be hot shortly after use!

Risk of burns.

– Detach the ring from the lamp cover.

Note: Make sure that the glass will not fall out

(Fig. 16).

– Pull out the lamp (Fig. 17).

Defective lamps must only be replaced by lamps of the same type! (12 V/20 W/G4 lampholder)

Inserting the lamp

– Insert the lamp in the lampholder.

Note: Do not touch the halogen lamps with your hands. Use a cloth and touch the lamp only on its edges.

– Engage the lamp cover.

– Connect the appliance to the mains again.

12

Fig. 17

6. Assembly instructions

6.1 Technical data

AH 530-790:

AH 530-720:

Weight: 23.5 kg

Dimensions: 35 3 /

8

´ ´ x 20 10 /

16

´ ´

898 x 550 mm

Weight: 27.5 kg

Dimensions: 47 3 /

16

´ ´ x 20 10 /

16

´ ´

1198 x 550 mm

Electrical connection

Pay attention to the rating plate data.

The appliance must only be connected by an authorised specialist . The specialist is responsible for perfect functioning of the appliance at its installation location. He must explain the operating principle of the appliance to the user with reference to the operating instructions. He must explain to the user how the appliance can be isolated from the mains whenever required.

Connection possibilities

It must be possible to isolate all poles of the appliance from the mains by way of the domestic fuse, or by means of accessible isolating device with a contact gap of at least 3 mm.

13

6.2 Installation

WARNING - TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

a.) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

b.) Sufficient air is needed for proper combustion end exhausting of gases through the flue

(chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire

Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air

Conditioning (ASHRAE), and the local code authorities.

c.) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d.) Ducted fans must always be vented to the outdoors.

e.) If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground

Fault Circuit Interrupter) - protected branch circuit.

f.) NEVER place a switch where it can be reached from a tub or shower.

WARNING:

To reduce the risk of fire, use only metal ductwork.

The applicable regulations of the energy supply companies and the regional construction regulations must be observed when installing the hood.

The minimum distance from the worktop to the bottom edge of the wall hood is for electrical appliances 24 ´ ´ / 600 mm and for gas appliances

27 1 /

2

´ ´ / 700 mm.

The wall hood was conceived for the exhaust air mode . The exhaust air can be routed into a separate exhaust air shaft or directly into the open through the outside wall.

It is not allowed to pass the exhaust air into a flue or exhaust air chimney that is in operation or into a shaft that is linked to the heating basement. Consult the chimney sweep responsible for your district whenever you wish to pass the exhaust air into a chimney that is not in operation.

During the course of planning , a chimney sweep must be consulted if a room air-dependent hearth is operated in the same room as the one in which a hood is operated in the exhaust air mode. Adequate incoming air must be ensured. The applicable construction and safety regulations must be observed.

Adequate incoming air must be ensured if a wood, coal, gas or oil heater or an open hearth is operated in the same room as the one in which the hood is installed.

Safe operation is possible whenever the partial vacuum in the place where the firing equipment is installed does not exceed 4 Pa (0.04 mbar).

This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/exhaust air wall boxes or other technical means.

14

Flexible aluminium pipes, corrosion-protected sheet metal pipes and exhaust air pipes whose material conforms to fire B1 in accordance with

DIN 4102 can be used. Exhaust air pipes should have a nominal diameter of 6 ´ ´ / 150 mm.

Pay particular attention to ensuring that

– the exhaust air ducts and pipes are kept as short as possible

– the pipes are not laid at an acute angle, but as bends and that they are inserted into the shaft at an inclined upward angle and

– there are no cross-sectional constrictions in the upward direction (this reduces the volume flow).

As standard , the blow-out opening of the wall hood is in the upward direction.

To pass exhaust air through the outer wall, we recommend the use of our telescopic wall box

TM 150-045 (Ø 6 ´ ´ / 150 mm).

Note:

To prevent the ingress of water, e.g. condensate or rain water from an uncovered exhaust air shaft, our condensate separator RV 060-150 must be installed in the exhaust air line. The condensate separator must still be acciessible after installation.

The duct units listed below are available depending on the height of the ceiling:

Stainless steel-design ventilation duct:

LK 530-010 for ceiling heights of

7 ´´ 3 ´ ´ - 8 ´´ 6 ´ ´ / 2.20 - 2.66 m

LK 530-020 for ceiling heights of

8 ´´ 6 ´ ´ - 10 ´´ 1 ´ ´ / 2.66 - 3.15 m

Aluminium-design ventilation duct:

LK 530-011 for ceiling heights of

7 ´´ 3 ´ ´ - 8 ´´ 6 ´ ´ / 2.20 - 2.66 m

LK 530-021 for ceiling heights of

8 ´´ 6 ´ ´ - 10 ´´ 1 ´ ´ / 2.66 - 3.15 m

The dimensions above refer to a distance of 5 ´´ 3 ´ ´ /

1.60 m from the floor to the bottom edge of the hood.

If required, individually sized ventilation ducts are available at an extra charge.

The power connection must be placed behind the duct cover on the wall.

260

(10 1 /

4

”)

100 (3

550

(21 10 /

16

”)

Fig. 18

15

15 ( 19 /

32

")

300

(11 13 /

16

")

310

(12 3 /

16

")

230

(9 1 /

16

")

76,5 (3")

396 (15 9 /

16

")

270

(10 5 /

8

")

62 (2 7 /

16

") min. 600 (24”) electric min. 700 (27 1 /

2

”) gas

782/1082

(35 3 /

8

" - 47 3 /

16

")

Fig. 19

Important: Before marking the securing holes, make sure that no electricity or water lines or other lines are laid at the drilling points in the wall.

Proceed as follows:

– From the bottom edge of the hood, mark a center line on the wall.

– With the aid of the drilling template, mark the positions of the screws on the wall (Fig. 19).

– Pay attention to the minimum clearance of 24 ´ ´ /

600 mm for electric cookers and 27 1 /

2

´ ´ / 700 mm for gas cookers. The bottom edge of the template corresponds to the bottom from edge of the hood.

– Using the drilling template, drill the 6 holes for the hood (area I of the drilling template) and the two holes for suspending the chimney (area II of the drilling template). In the top two securing holes for the hood, fix the two hooks d with the countersunk screws c . Make sure that the hooks lie flatly on the wall. In certain circumstances you may have to countersink the drill holes. Fit the included dowels a in the other drill holes.

Note: Pay attention to any special accessories that you may have to fit.

– Screw on the retaining bracket for the chimney paneling.

– Detach the grease filters.

– Hang the hood on the two hooks. Adjust the suspended element with the recessed head screw and align the hood using a spirit level

(Fig. 20).

16

Fig. 20

Fig. 21

Fig. 22

5750197383 en 11.01 SK

– Secure the hood on the wall with the four screws b (Fig. 21).

– Establish the pipe connection.

– Establish the electrical connection.

– Stainless steel chimney only (LK 530-010/020):

Pull the protective film off the chimney’s trims.

Note: Avoid damaging the sensitive metal surfaces.

– Fit the top of the chimney into the base. Make sure that the fastening holes on the side are at the top.

– Put both chimney parts onto the hood.

– Pull the chimney top duct up into its final position and secure the top duct unit with 2 screws on the ceiling holder (Fig. 22).

Note: Avoid scratching the surface when pulling out the top duct element, for example by placing the assembly template over the edge of the bottom chimney duct to protect it.

– Reinsert the grease filters.

– Place the glass plates on the appliance with the printed side facing down.

Note: When putting the glass trays in place, make sure that you do not scratch the chimney.

17

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement