ESAB Remote Pendant Instruction manual

Add to my manuals
12 Pages

advertisement

ESAB Remote Pendant Instruction manual | Manualzz

REMOTE PENDANT OPERATING INSTRUCTIONS

Manual 0-5263

Remote Pendant

Cigweld Pty Ltd

71 Gower Street

Preston, Victoria, Australia, 3072

Telephone: +61 3 9474 7400 • FAX: +61 3 9474 7391

Email: [email protected]

Website: www.cigweld.com.au

Trigger

Knob

Part Number: W4016900

Instruction Sheet

Pin

F

G

H

I, J

A

B, C

D

E

8 Pin Receptacle

10 Pin

10 Pin

Description

Potentiometer Wiper

Not Used

Trigger Switch

Potentiometer Maximum

Not Used

Trigger Switch

Potentiometer Minimum

Not Used

Control Pendant

Art # A-12069

Art # A-12068

Pin

7

8

5

6

3

4

1

2

8 Pin

8m 10P-8P Connecting Cable (supplied with the control pendant)

8 Pin

Potentiometer Maximum

Potentiometer Minimum

Not Used

3

1

6

Description

Not Used

Trigger Switch

Trigger Switch

Not Used

8

2

5

Potentiometer Wiper

© 2013 by Victor Technologies Industries

0-5263 1 May 15, 2013

REMOTE PENDANT

WARNING

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks or severe burns. The electrode and work circuit is electrically live whenever the output is on. The input power circuit and machine internal circuits are also live when power is on. In semiautomatic or automatic wire welding, the wire, wire reel, drive roll housing, and all metal parts touching the welding wire are electrically live.

Incorrectly installed or improperly grounded equipment is a hazard.

1. Do not touch live electrical parts.

2. Wear dry, hole-free insulating gloves and body protection.

3. Insulate yourself from work and ground using dry insulating mats or covers.

4. Disconnect input power or stop engine before installing or servicing this equipment. Lock input power disconnect switch open, or remove line fuses so power cannot be turned on accidentally.

5. Properly install and ground this equipment according to its Owner’s Manual and national, state, and local codes.

6. Turn off all equipment when not in use. Disconnect power to equipment if it will be left unattended or out of service.

7. Use fully insulated electrode holders. Never dip holder in water to cool it or lay it down on the ground or the work surface. Do not touch holders connected to two welding machines at the same time or touch other people with the holder or electrode.

8. Do not use worn, damaged, undersized, or poorly spliced cables.

9. Do not wrap cables around your body.

10. Ground the workpiece to a good electrical (earth) ground.

11. Do not touch electrode while in contact with the work (ground) circuit.

12. Use only well-maintained equipment. Repair or replace damaged parts at once.

13. In confined spaces or damp locations, do not use a welder with AC output unless it is equipped with a voltage reducer. Use equipment with DC output.

14. Wear a safety harness to prevent falling if working above floor level.

15. Keep all panels and covers securely in place.

WARNING

ARC RAYS can burn eyes and skin; NOISE can damage hearing.

Arc rays from the welding process produce intense heat and strong ultraviolet rays that can burn eyes and skin. Noise from some processes can damage hearing.

1. Use a Welding Helmet or Welding Faceshield fitted with a proper shade of filter (see ANSI Z49.1 and AS

1674 listed in Safety Standards) to protect your face and eyes when welding or watching.

2. Wear approved safety glasses. Side shields recommended.

3. Use protective screens or barriers to protect others from flash and glare; warn others not to watch the arc.

May 15, 2013 2 0-5263

REMOTE PENDANT

4. Wear protective clothing made from durable, flame-resistant material (wool and leather) and foot protection.

5. Use approved ear plugs or ear muffs if noise level is high.

6. Never wear contact lenses while welding.

WARNING

FUMES AND GASES can be hazardous to your health.

Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health.

1. Keep your head out of the fumes. Do not breath the fumes.

2. If inside, ventilate the area and/or use exhaust at the arc to remove welding fumes and gases.

3. If ventilation is poor, use an approved air-supplied respirator.

4. Read the Material Safety Data Sheets (MSDSs) and the manufacturer’s instruction for metals, consumables, coatings, and cleaners.

5. Work in a confined space only if it is well ventilated, or while wearing an air-supplied respirator. Shielding gases used for welding can displace air causing injury or death. Be sure the breathing air is safe.

6. Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapours to form highly toxic and irritating gases.

7. Do not weld on coated metals, such as galvanized, lead, or cadmium plated steel, unless the coating is removed from the weld area, the area is well ventilated, and if necessary, while wearing an air-supplied respirator. The coatings and any metals containing these elements can give off toxic fumes if welded.

WARNING

WELDING can cause fire or explosion.

Sparks and spatter fly off from the welding arc. The flying sparks and hot metal, weld spatter, hot workpiece, and hot equipment can cause fires and burns. Accidental contact of electrode or welding wire to metal objects can cause sparks, overheating, or fire.

1. Protect yourself and others from flying sparks and hot metal.

2. Do not weld where flying sparks can strike flammable material.

3. Remove all flammables within 35 ft (10.7 m) of the welding arc. If this is not possible, tightly cover them with approved covers.

4. Be alert that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas.

5. Watch for fire, and keep a fire extinguisher nearby.

6. Be aware that welding on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side.

7. Do not weld on closed containers such as tanks or drums.

8. Connect work cable to the work as close to the welding area as practical to prevent welding current from travelling long, possibly unknown paths and causing electric shock and fire hazards.

9. Do not use welder to thaw frozen pipes.

10. Remove stick electrode from holder or cut off welding wire at contact tip when not in use.

0-5263 3 May 15, 2013

REMOTE PENDANT

WARNING

FLYING SPARKS AND HOT METAL can cause injury.

Chipping and grinding cause flying metal. As welds cool, they can throw off slag.

1. Wear approved face shield or safety goggles. Side shields recommended.

2. Wear proper body protection to protect skin.

WARNING

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode.

Since gas cylinders are normally part of the welding process, be sure to treat them carefully.

1. Protect compressed gas cylinders from excessive heat, mechanical shocks, and arcs.

2. Install and secure cylinders in an upright position by chaining them to a stationary support or equipment cylinder rack to prevent falling or tipping.

3. Keep cylinders away from any welding or other electrical circuits.

4. Never allow a welding electrode to touch any cylinder.

5. Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and associated parts in good condition.

6. Turn face away from valve outlet when opening cylinder valve.

7. Keep protective cap in place over valve except when cylinder is in use or connected for use.

8. Read and follow instructions on compressed gas cylinders, associated equipment, and CGA publication

P-1 listed in Safety Standards.

WARNING

MOVING PARTS can cause injury.

Moving parts, such as fans, rotors, and belts can cut fingers and hands and catch loose clothing.

1. Keep all doors, panels, covers, and guards closed and securely in place.

2. Stop engine before installing or connecting unit.

3. Have only qualified people remove guards or covers for maintenance and troubleshooting as necessary.

4. To prevent accidental starting during servicing, disconnect negative (-) battery cable from battery.

5. Keep hands, hair, loose clothing, and tools away from moving parts.

6. Reinstall panels or guards and close doors when servicing is finished and before starting engine.

!

WARNING

This product, when used for welding or cutting, produces fumes or gases which contain chemicals know to the State of California to cause birth defects and, in some cases, cancer. (California

Health & Safety code Sec. 25249.5 et seq.)

NOTE

Considerations About Welding And The Effects of Low Frequency Electric and Magnetic Fields

May 15, 2013 4 0-5263

REMOTE PENDANT

The following is a quotation from the General Conclusions Section of the U.S. Congress, Office of Technology

Assessment, Biological Effects of Power Frequency Electric & Magnetic Fields - Background Paper, OTA-BP-

E-63 (Washington, DC: U.S. Government Printing Office, May 1989): “...there is now a very large volume of scientific findings based on experiments at the cellular level and from studies with animals and people which clearly establish that low frequency magnetic fields and interact with, and produce changes in, biological systems. While most of this work is of very high quality, the results are complex. Current scientific understanding does not yet allow us to interpret the evidence in a single coherent framework. Even more frustrating, it does not yet allow us to draw definite conclusions about questions of possible risk or to offer clear science-based advice on strategies to minimize or avoid potential risks.”

To reduce magnetic fields in the workplace, use the following procedures.

1. Keep cables close together by twisting or taping them.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cable around the body.

4. Keep welding power source and cables as far away from body as practical.

ABOUT PACEMAKERS:

The above procedures are among those also normally recommended for pacemaker wearers.

Consult your doctor for complete information.

0-5263 5 May 15, 2013

REMOTE PENDANT

Air - Arc Gouging

Recommended Protective Filters for Electric Welding

Description of Process

Manual Metal Arc Welding - covered electrodes (MMAW)

Gas Metal Arc Welding (GWAW)

(MIG) other than Aluminium and

Stainless Steel

Gas Metal Arc Welding (GMAW)

(MIG) Aluminium and Stainless Steel

Gas Tungsten Arc Welding (GTAW)

(TIG)

Flux-cored Arc Welding (FCAW) -with or without shielding gas.

Plasma - Arc Cutting

Plasma - Arc Spraying

Plasma - Arc Welding

Submerged - Arc Welding

Resistance Welding

Approximate Range of

Welding Current in Amps

Less than or equal to 100

100 to 200

200 to 300

300 to 400

Greater than 400

Less than or equal to 150

150 to 250

250 to 300

300 to 400

Greater than 400

Less than or equal to 250

250 to 350

Less than or equal to 100

100 to 200

200 to 250

250 to 350

Greater than 350

Less than or equal to 300

300 to 400

400 to 500

Greater than 500

Less than or equal to 400

50 to 100

100 to 400

400 to 800

Less than or equal to 20

20 to 100

100 to 400

400 to 800

Minimum Shade Number of

Filter(s)

8

10

11

12

13

10

11

12

13

14

12

13

10

11

12

13

14

11

12

13

14

12

10

12

14

15

8

10

12

14

2(5)

Safety Spectacles or eye shield

Refer to standard AS/NZS 1338.1:1992 for comprehensive information regarding the above table

May 15, 2013 6 0-5263

REMOTE PENDANT

Description

The CIGWELD Remote Pendant consists of a trigger switch and volts control potentiometer. It is specially designed to allow use of voltage sensing wirefeeders with a range of CIGWELD power sources.

The trigger enables and disables the Power Source welding output, and the potentiometer controls welding voltage.

Refer to list below for compatible CIGWELD power sources.

Installation

Attach the 8-pin connector on one end of the 10p-8p cable to the 8-pin receptacle on the front of the remote pendant. And attach the 10-pin connector to the 10-pin receptable on the front of the welding machine. To complete the connection, align the keyway, insert the plug, and rotate the threaded collar fully clockwise.

Operation

Set the trigger switch to "1" position to start the machine output functions. The remote pendant potentiometer controls the welding voltage up to the level set on the welding power source. Note that the maximum voltage must be set on the power source by the operator prior to the remote pendant being connected. With the remote pendant connected, the power source will only display minimum preview Volts until the Knob is rotated then it displays actual welding voltage when welding. Rotate the knob clockwise to increases the welding voltage; turning anti-clockwise decreases the welding voltage. Reseting the tirgger to "0" position completely extinguishes the arc and initiates the post-flow shielding gas timer (where fitted).

This remote pendant is fully compatible with the following CIGWELD power sources:

Transmig 350i Part No: W1005353 and W1005359

Transmig 450i Part No: W1005453

Transmig 550i Part No: W1005553

Note 1: Other Power Source may not be fully compatible with the remote pendant.

The remote pendant potentiometer controls the welding voltage up to the level set on the welding power source.

Note that the maximum voltage must be set on the power source by the operator prior to the remote pendant being connected. Rotate the remote pendant potentiometer clockwise to increase the welding voltage; rotate anti-clockwise to decrease the welding voltage. The Power Source will preview the welding volts.

Set the Power Source to 10 pin Remote mode by pressing the remote / local button so the Remote LED is on, and by pressing the 10 pin / 19 pin button until the 10 pin LED is on. The remote control pendant potentiometer can adjust between 0 - 100% of the Power Source output volts setting. As an example, if the output voltage on the power source front panel is set to 35V, the remote control device will be able to adjust between 14V to

35V over its complete range of rotation. If higher welding voltage is required, set the Power Source to Local mode, adjust the output voltage, then return the Power Source to Remote mode.

Set the trigger switch to the "1" position to turn on the Power Source welding power output. Set the trigger switch to "0" to turn off the Power Source welding power output.

Note 2: On some Power Sources, the welding output voltage at no load may be higher than the welding output voltage.

0-5263 7 May 15, 2013

REMOTE PENDANT

TERMS OF WARRANTY – JANUARY 2013

1. The Trade Practices Act 1974 (Commonwealth) and similar State Territory legislation relating to the supply of goods and services, protects consumers’ interests by ensuring that consumers are entitled in certain situations to the benefit of various conditions, warranties, guarantees, rights and remedies

(including warranties as to merchantability and fitness for purpose) associated with the supply of goods and services. A consumer should seek legal advice as to the nature and extent of these protected interests. In some circumstances, the supplier of goods and services may legally stipulate that the said conditions, warranties, guarantees, rights and remedies are limited or entirely excluded. The warranties set out in Clause 2 shall be additional to any nonexcludable warranties to which the Customer may be entitled pursuant to any statute.

2. Subject to Clause 3. CIGWELD gives the following warranties to the Customer:

Insofar as they are manufactured or imported by CIGWELD, goods will upon delivery be of merchantable quality and reasonably fit for the purpose for which they are supplied by CIGWELD.

CIGWELD will repair or, at its option, replace those of the goods which, upon examination, are found by

CIGWELD to be defective in workmanship and/or materials.

CIGWELD reserves the right to request documented evidence of date of purchase.

3. The Warranty in Clause 2;

Is conditional upon:

The Customer notifying CIGWELD or our Accredited Distributor in writing of its claim within seven (7) days of becoming aware of the basis thereof, and at its own expense returning the goods which are the subject of the claim to CIGWELD or nominated Accredited Distributor/Accredited Service Provider.

The goods being used in accordance with the Manufacturer’s Operating Manuals, and under competent supervision.

Does not apply to:

Obsolete goods sold at auction, second-hand goods and prototype goods.

Breakdown or malfunction caused by accident, misuse or normal wear and tear.

Repairs or replacement made other than by CIGWELD or Accredited Service Providers, unless by prior arrangement with CIGWELD.

Replacement parts or accessories which may affect product safety or performance and which are not manufactured, distributed or approved by CIGWELD.

4. CIGWELD declares that, to the extent permitted by law, it hereby limits its liability in respect of the supply of goods which are not of a kind ordinarily acquired for personal, domestic or household use or consumption to any one or more of the following (the choice of which shall be at the option of CIGWELD).

The replacement of the goods or the supply of equivalent goods.

The repair of goods.

The payment of cost of replacing the goods or acquiring equivalent goods.

The payment of the cost of having goods repaired.

5. Except as provided in Clauses 2 to 4 above, to the extent permitted by statute, CIGWELD hereby excludes all liability for any loss, damage, death or injury of any kind whatsoever occasioned to the

Customer in respect of the supply of goods including direct, indirect, consequential or incidental loss, damage or injury of any kind.

May 15, 2013 8 0-5263

REMOTE PENDANT

WARRANTY SCHEDULE – JANUARY 2013

These warranty periods relate to the warranty conditions in clause 2. All warranty periods are from date of sale from the Accredited Distributor of the equipment. Notwithstanding the foregoing, in no event shall the warranty period extend more than the time stated plus one year from the date CIGWELD delivered the product to the Accredited Distributor. Unless otherwise stated the warranty period includes parts and labour.

CIGWELD reserves the right to request documented evidence of date of purchase.

WARRANTY PERIOD

REMOTE PENDANT

3 Months

Please note that the information detailed in this statement supersedes any prior published data produced by

CIGWELD.

0-5263 9 May 15, 2013

Australia Terms of Warranty – 2013

Effective 1st January 2012, all warranties against defects (also known as a manufacturer’s warranty) supplied with goods or services must comply with the new Australian consumer law regulations (2010).

This Warranty Statement should be read in conjunction with the Warranty Schedule contained in the operating instructions of the product. This schedule contains the warranty period applicable to the product

Any claim under this warranty must be made within the warranty period which commences on the date of purchase of the product. To make a claim under the warranty, take the product

(with proof of purchase from a Cigweld Accredited Seller) to the store where you purchased the product or contact Cigweld Customer Care 1300 654 674 for advice on your nearest Service

Provider.

All costs associated with lodging the warranty claim including the return of goods to Cigweld or our Nominated Accredited Distributor/Accredited Service Provider are the responsibility of the consumer.

This warranty is given.

Cigweld Pty Ltd

A.B.N. 56007226815

71 Gower Street, Preston

Victoria, Australia, 3072

Phone: 1300 654 674

Email: [email protected]

Website: www.cigweld.com.au

This warranty is provided in addition to other rights and remedies you have under law: Our goods come with guarantees which cannot be excluded under the Australian Consumer Law.

You are entitled to replacement or refund for a major failure and to compensation for other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Failures due to incorrect use are not covered by this warranty and consumers are reminded to only use the product in accordance with the Operating Instruction supplied with the product.

Additional copies of Operating Instructions are available from Cigweld Customer Care 1300 654

674 or the Website.

GLOBAL CUSTOMER SERVICE CONTACT INFORMATION

Cigweld, Australia

71 Gower Street

Preston, Victoria

Australia, 3072

Telephone: 61-3-9474-7400

Fax: 61-3-9474-7391

Email: [email protected]

Victor Technologies USA

2800 Airport Road

Denton, Tx 76207 USA

Telephone: (940) 566-2000

800-426-1888

Fax: 800-535-0557

Email: [email protected]

Victor Technologies Canada

2070 Wyecroft Road

Oakville, Ontario

Canada, L6L5V6

Telephone: (905)-827-1111

Fax: 905-827-3648

Victor Technologies Europe

Europe Building

Chorley North Industrial Park

Chorley, Lancashire

England, PR6 7Bx

Telephone: 44-1257-261755

Fax: 44-1257-224800

PT. Victor Technologies Utama Indonesia

Jl. Angsana II Blok AE No. 28

Delta Silicon I, Cikarang - Sukaresmi

Bekasi, 17550

Indonesia

Tel: +62 21 8990 6095

Fax: +62 21 8990 6096 / 1867 http://www.victortechnologies.com

Victor Technologies, China

No.100 Lao Hongjing Rd,

Minhang District

Shanghai 200235

China

Telephone: 86-21-64072626

Fax: 86-21-64483032

Victor Technologies Asia Sdn Bhd

Lot 151, Jalan Industri 3/5A

Rawang Integrated Industrial Park - Jln Batu Arang

48000 Rawang Selangor Darul Ehsan

West Malaysia

Telephone: 603+ 6092 2988

Fax : 603+ 6092 1085

Victor Technologies Italy

OCIM, S.r.L.

Via Benaco, 3

20098 S. Giuliano

Milan, Italy

Tel: (39) 02-98 80320

Fax: (39) 02-98 281773

Victor Technologies International

2070 Wyecroft Road

Oakville, Ontario

Canada, L6L5V6

Telephone: (905)-827-9777

Fax: 905-827-9797

Asia Pacific Regional Headquarters

71 Gower Street

Preston, Victoria, Australia, 3072

Telephone: +61 3 9474 7400

FAX: +61 3 9474 7391

Email: [email protected]

www.cigweld.com.au

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement