Owner’s Manual & Safety Instructions
Save This Manual
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
21a
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.
Copyright © 2020 by Harbor Freight Tools ® . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Read this material before using this product.
Failure to do so can result in serious injury.
Page 1
Tools required for assembly and service may not be included.
READ AND SAVE THESE INSTRUCTIONS.
RULES FOR SAFE OPERATION
1. WARNING! TO PREVENT SERIOUS
INJURY: To reduce the risk of fire or electric shock, do not use this
Fan with any solid-state speed control device.
10.
11.
DO NOT use fan in window.
Rain may create electrical hazard.
Complete the assembly of the fan before switching on the fan.
2. This appliance is for use on a nominal 120-V circuit and has a grounding attachment plug.
Make sure that the appliance is connected to an outlet having the same configuration as the plug.
No adaptor should be used with this appliance.
12. Maintain labels and nameplates on the fan.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
13. Use only in dry areas.
Do not use in bathrooms, laundry area, near sinks or other sources of water.
3. Do not leave Fan running while unattended.
14. This fan is not a toy.
Keep it out of reach of children.
4. Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
15. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
5. Do not run cord under carpeting.
Do not cover cord with throw rugs, runners, or similar coverings.
Arrange cord away from traffic area and where it will not be tripped over.
6. Never insert fingers, pencils, or any other object through Front or Rear
Blade Guards.
7. Disconnect Fan when moving it from one location to another.
16. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all conditions and situations that may occur. It must be understood by operator that common sense and caution are factors which cannot be built into this fan, but must be supplied by operator.
8. Disconnect Fan before removing grills for cleaning.
9. Be sure fan is on a stable surface when operating to avoid overturning.
Item 93532 For technical questions, please call 1-888-866-5797. Page 2
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Addresses practices not related to personal injury.
Specifications
Fan Blade
Fan Guard
Diameter
Motor
Amperage
120 VAC, Single Phase Continuous Duty
High -1.85, Low - 1.45
HOUSEHOLD USE ONLY
Item 93532 For technical questions, please call 1-888-866-5797. Page 3
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
ASSEMBLY AND OPERATING INSTRUCTIONS
NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 9 .
Warning!
Always make sure the Power Cord of the Fan is unplugged from its electrical outlet prior to making any adjustments to the fan.
Warning! To reduce the risk of fire or electric shock, do not use this fan with any solidstate speed control device.
ASSEMBLY
1. Attach the two Wheels (16) to the Drum (5) using one Bolt (17) per Wheel.
2. Assemble the Foot Stand (18) to the Drum (5) using four Bolts (20).
3. Inspect the fully assembled fan with it resting on its wheels and the base.
IMPORTANT: The Pads at the bottom of the Base MUST sit flat on the floor.
If they do not, remove the Foot Stand (18), turn it 180°, and reinstall it.
OPERATION
1. Situate the Fan in a dry location out of children’s reach and away from normal room traffic.
2. Plug in the Power Cord (10).
3. Set the Control (13) to either LOW or HIGH, depending on your preference.
4. When finished, set the Control (13) to OFF.
Item 93532 For technical questions, please call 1-888-866-5797. Page 4
INSPECTION, MAINTENANCE, AND CLEANING
1. WARNING! TO PREVENT SERIOUS INJURY: Make sure the Control (13) of the Fan is in its “OFF” position and that the Fan is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
2. BEFORE EACH USE, inspect the general condition of the Fan. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use.
Do not use damaged equipment.
3. Periodically, check to see that the Blade (3) has no dirt or debris accumulating on its surface. If necessary, use compressed air to clean the unit.
4. Before each use, check that the Power Cord (10) has no tears, frays, or cracks.
Do not use the Fan if you find any irregularities. Contact a qualified service technician.
Item 93532 For technical questions, please call 1-888-866-5797. Page 5
PARTS LIST
Part Description Qty.
1 Screw
2 Front Guard
6
1
3 Blade
4 Screw
5 Drum
6 Handle
7 Rear Guard
8 Washer
9 Switch Box
10 Power Cord
11 Switch
12 Capacitor
13 Control
14 Motor
15 Wheel Holder
16 Wheel
17 Wheel Bolt
18 Foot Stand
19 Rubber Foot
20 Foot Stand Bolt
2
10
1
1
1
1
2
1
1
1
6
1
2
2
4
2
2
2
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Item 93532 For technical questions, please call 1-888-866-5797. Page 6
ASSEMBLY DIAGRAM
NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Reference UPC 193175334145.
Item 93532 For technical questions, please call 1-888-866-5797. Page 7
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
