Aten VS482B Video Switch User Manual

4-Port True 4K HDMI Switch with Dual Output

VS482B User Manual

www.aten.com

VS482B User Manual

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Caution : Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Warning : Operation of this equipment in a residential environment could cause radio interference.

Achtung: Der Gebrauch dieses Geräts in Wohnumgebung kann

Funkstörungen verursachen.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

KCC Statement

RoHS

This product is RoHS compliant.

© Copyright 2020 ATEN® International Co., Ltd.

Manual Date: 2020-12-16

ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.

All other brand names and trademarks are the registered property of their respective owners. The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. ii

VS482B User Manual

User Information

Online Registration

Be sure to register your product at our online support center:

International http://eservice.aten.com

Telephone Support

For telephone support, call this number:

International

China

Japan

Korea

North America

886-2-8692-6959

86-400-810-0-810

81-3-5615-5811

82-2-467-6789

1-888-999-ATEN ext 4988

1-949-428-1111

User Notice

All information, documentation, and specifications contained in this manual are subject to change without prior notification by the manufacturer. The manufacturer makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the manufacturer's software described in this manual is sold or licensed as is .

Should the programs prove defective following their purchase, the buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV interference caused by unauthorized modifications to this device. It is the responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

iii

VS482B User Manual

Package Contents

 1 VS482B 4-Port True 4K HDMI Switch with Dual Output

 1 IR Remote Control Unit

 1 Power Adapter

 1 Mounting kit

 1 User Instructions*

Note: 1. Make sure that all the components are present and in good order.

If anything is missing or was damaged in shipping, contact your dealer.

2. Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit, and/or any of the devices connected to it.

iv

VS482B User Manual

Contents

EMC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

1. Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Source Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Display Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

VS482B Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

VS482B Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

IR Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2. Hardware Setup

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

VS482B Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing the RS-232 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3. Operation

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Manual Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Remote Control Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Switch Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Audio Return Channel (ARC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Enabling ARC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

IR Command Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

RS-232 Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Configuring the Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Switch Port Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

v

VS482B User Manual

Standby/Power Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Switch Mode Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

EDID Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

CEC Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Mute Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

ARC Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Echo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Baud Rate Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Powering Off and Restarting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

OSD Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Input Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Audio Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

OSD Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

System Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

4. The Firmware Upgrade Utility

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . . 35

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

vi

VS482B User Manual

About this Manual

This User Manual is provided to help you get the most from your VS482B system. It covers all aspects of installation, configuration and operation. An overview of the information found in the manual is provided below.

Chapter 1, Introduction, introduces you to the VS482B system. Its purpose, features and benefits are presented, and its front and back panel components are described.

Chapter 2, Hardware Setup, describes how to set up your VS482B installation and all necessary steps are provided.

Chapter 3, Operation, explains the fundamental concepts involved in operating the VS482B via the front panel pushbuttons, remote control, RS-232 serial interface and OSD menu. In addition, Switch Modes, Audio Return

Channel (ARC) and RS-232 commands are discussed in detail.

Chapter 4, The Firmware Upgrade Utility, explains how to download the VS482B’s firmware and upgrade the device using the utility.

An Appendix, provides specifications and other technical information regarding the VS482B.

vii

VS482B User Manual

Conventions

This manual uses the following conventions:

Monospaced

[ ]

1.

♦

→

Indicates text that you should key in.

Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them:

[Ctrl+Alt].

Numbered lists represent procedures with sequential steps.

Bullet lists provide information, but do not involve sequential steps.

Indicates selecting the option (on a menu or dialog box, for example), that comes next. For example, Start

→

Run means to open the Start menu, and then select Run .

Indicates critical information.

Product Information

For information about all ATEN products and how they can help you connect without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

International

North America http://www.aten.com

http://www.aten-usa.com

viii

Chapter 1

Introduction

Overview

The ATEN VS482B Switch is an ideal solution for application requiring superior video resolution of True 4K when connecting 4 HDMI A/V sources to

2 HDMI displays. Complying with HDMI, the switch’s Audio Return Channel

(ARC) function allows users to send audio without having to attach a separate audio cable.

Furthermore, the VS482B offers switching methods between HDMI sources by front panel pushbuttons, IR remote control and RS-232 commands, enabling users to effortlessly select desired input. Equipped with EDID

Expert™, the VS482B benefits users with optimum EDID settings for smooth power-up and highest-quality display across different screens. Featuring above functionalities provides you a practical solution for auditorium, home theater, meeting rooms, trade shows, shopping centers, and more.

1

VS482B User Manual

Features

 Allows up to 4 HDMI A/V sources to be connected to 2 HDMI displays

 Superior video quality – up to 4096 x 2160 / 3840 x 2160 @ 60Hz (4:4:4);

HDR supported

 HDMI (3D, Audio Return Channel, Deep Color); HDCP 2.2 compliant

 Supports Auto Switch – the VS482B automatically switches to a newly plugged-in source

 Audio Return Channel (ARC) function – connects an HDMI cable to the

ARC port to send audio from your source device to your audio/video receiver

 OSD for system configuration settings and information display

 Switching between HDMI input sources via front panel pushbuttons, IR remote control and RS-232 commands

 EDID Expert™ – selects optimum EDID settings for smooth power-up, high-quality display, and use of the best resolution across different screens

 Built-in bi-directional RS-232 serial control port for high-end system control

 HDMI audio can be extracted to stereo audio and digital audio (optical/ coaxial) outputs

 Supports 5.1 channel audio output

 Supports Consumer Electronic Control (CEC)

 Rack mountable

2

Chapter 1. Introduction

Requirements

The following equipment is required for a complete VS482B installation:

Source Device

 HDMI Type A output connector(s)

Note: A DVI/HDMI adapter is required when connecting a DVI source device.

Display Device

 Up to 2 display devices or receivers with an HDMI Type A input connector

Cables

 4 HDMI cables

Note: 1. No cables are included in this package. We strongly recommend that you purchase high-quality cables of appropriate length since this will affect the quality of the audio and video display. Contact your dealer to purchase the correct cable sets.

2. If you wish to utilize the VS482B’s high-end serial controller function, you will also need to purchase an appropriate RS-232 cable.

See Installing the RS-232 Controller , page 10.

3

VS482B User Manual

Components

VS482B Front View

1 2 3 4 5

6 7

No.

1

Component

Port LEDs

2 ARC LED

3

4

Power Pushbutton

Power LED

5

6

IR Receiver

Port Selection

Pushbuttons

7 ARC button

Description

The selected port’s LED (green) lights up to indicate that the port is selected.

The LED (blue) lights up when the ARC function is enabled.

Press this button to turn on / off the switch.

 The LED (green) lights up when the switch is powered on.

 The LED (orange) lights up to indicate that the switch is in standby mode.

This receives signals from the IR remote control.

Pressing a port selection pushbutton routes the A/V source from the corresponding input port to the output port for display.

Press this button to enable / disable the ARC function.

4

Chapter 1. Introduction

VS482B Rear View

1 2 3 4 5 6 7 8

No.

1

2

3

Component

Power Jack

IR EXT (Extender)

Port

RS-232 Serial Port

4

5

6

Stereo Audio Out

Ports

Digital Audio Out

Ports

HDMI Out Port

(port 2)

7 HDMI Out Port

(port 1) (ARC In)

8 HDMI In Ports

Description

The power adapter cable plugs in here.

Connect the IR Extender to this port.

Note: The IR receiver can be purchased separately.

This is the serial remote port for input source selection and high-end system control, including firmware upgrade.

The red port is for the right audio channel, and the white port is for the left audio channel.

Connect the optical and coaxial audio cables to these ports.

The cable from the HDMI display or receiver device plugs in here.

Note: The ARC audio signal will be transmitted when the ARC is enabled. For more information, see

Enabling ARC , page 14.

 The cable from the HDMI display device or receiver plugs in here.

 Connect the ARC audio input connector or receiver to this port. The ARC audio can be transmitted back

(to audio receivers) through this connectivity

The cables from the HDMI source devices can plug into any of four available ports.

5

VS482B User Manual

IR Remote Control

1

2

3

4

5

6

7 8

9

2

3

4

5

No.

1

6

7

8

9

Component

Up / Down / Left /

Right Arrows

Setup

On

Off

Press this to power on the display.

Press this to power off the display.

Port Selection Buttons

1~4

Press a button to bring the focus directly to the source device attached to its associated port.

Menu

Info button

ARC

HDMI Mute

Description

Press the Up / Down / Left / Right button to cycle through the OSD menu/selection.

Press this to confirm the selection on the OSD screen.

Press this to open / close the OSD menu.

Press this button to display information about the source device on the upper left side of the screen. The information can include: Source port number; Source port number + Source Type; or turned off.

Enable / Disable ARC function. See ARC Commands , page 24.

Enable / Disable audio for the HDMI output port.

See Switch Mode , page 12.

6

Chapter 2

Hardware Setup

1. Important safety information regarding the placement of this

device is provided on page 41. Please review it before

proceeding.

2. Make sure that the power to all devices connected to the installation are turned off.

3. Make sure that all devices you will be installing are properly grounded.

Rack Mounting

For convenience and flexibility, the VS482B can be mounted on system racks.

To rack mount a unit do the following:

1. Using the screws provided in the Mounting Kit, screw the mounting bracket to the side of the unit as show in the diagram below:

Phillips hex head

M3x6

7

VS482B User Manual

2. Screw the bracket into a convenient location on the rack.

Note: These screws are not provided. We recommend that you use M5 x 12

Phillips Type I cross, recessed type screws.

Grounding

To prevent damage to your installation it is important that all devices are properly grounded.

1. Use a grounding wire to ground the VS482B by connecting one end of the wire to the grounding terminal, and the other end of the wire to a suitable grounded object.

2. Make sure that the devices that the VS482B connects to are properly grounded.

8

Chapter 2. Hardware Setup

Installation

Installation of the VS482B is simply a matter of plugging in the appropriate cables.

VS482B Installation

To install the switch, refer to the installation diagram below as you perform the following steps:

1. Connect your audio devices (such as speakers or AVRs) to the Stereo

Audio Out Ports or Digital Audio Out Ports.

2. Use an HDMI cable to connect the HDMI Input port on the video display device to the HDMI Out Ports on the back of the VS482B.

3. Use HDMI cables to connect the HDMI Output ports on the source device(s) to the HDMI In Ports on the back of the VS482B.

4. (Optional) To edit the VS482B system settings through the RS-232 Serial

Port, connect the hardware / software controller here.

5. Plug the provided power adapter into an appropriate AC power source; plug the power adapter cable into the Power Jack on the back of the

VS482B.

6. Power on the VS482B, the display, and source devices.

HDMI Source Devices

Power

Jack

5

Hardware / Software

Controller

4

3

1

Multi-channel Audio

2 or or

HDMI Output Devices

9

VS482B User Manual

Installing the RS-232 Controller

In order to use the RS-232 serial interface to attach a high-end controller (such as a PC) to the VS482B, use a serial cable such as a modem cable. The end connecting to the VS482B should have a 9-pin male connector. Connect this to the serial interface on the rear of the VS482B. Refer to number 5 on the previous diagram.

Note:

To configure the controller serial port, see page 16.

10

Chapter 3

Operation

Overview

The 4-Port True 4K HDMI Switch with Dual Output offers easy and flexible source device selection with either the front panel pushbuttons, remote control, or through the RS-232 serial interface, and system settings via OSD menu.

Note: 1. Whenever the VS482B is powered on and there is no video input source connected, it automatically selects Port 1 as the active port

(i.e., the Port 1 LED lights up). You may choose one of the methods outlined below to select a different port as your active port.

2. The VS482B takes about 10-20 seconds to boot up and apply system configuration settings when first powered on.

Manual Port Selection

To select an HDMI source device, press the pushbutton on the front panel that corresponds to the port to which the device is connected.

Note: The Port LED (green) light indicates which port is currently selected.

Remote Control Selection

To select a source device with the remote control, press the number button that corresponds to the port which the HDMI device is connected.

See IR Remote Control , page 6 for more details.

Note: Aim the remote control at the IR receiver located on the front panel of the VS482B. For optimum performance, make sure there is a clear lineof-sight between the remote control unit and the IR receiver.

11

VS482B User Manual

Switch Mode

You can choose how the VS482B behaves when a new input source is

connected. The switch modes can be set via RS-232 commands (see Switch

Mode Commands , page 19) by connecting a computer or hardware controller

to the VS482’s RS-232 port. If you are using a computer you can download the

RS-232 AP GUI from our website to configure these additional settings. There are three Switch Modes as follows:

 Default – The switch behaves normally without automatic switching operation.

 Next – Switch priority is placed on the next port that has a new source connected to it (default).

 Auto – Places priority on a selected port so that when a source is connected to the said port, the VS482B automatically switches to it, and the port can not be changed until the source is unplugged or auto switching is disabled.

In addition, the Go To function, which can be turned On or Off via RS-232 commands, enables the VS482B to switch to the next port with a powered on source device when the current input source is off. Refer to

Switch Mode

Commands , page 19 for more details.

12

Chapter 3. Operation

Audio Return Channel (ARC)

Audio Return Channel (ARC) allows an HDMI source device that receives content via air waves (such as a TV or STB connected to a satellite antenna) to send audio “upstream” to your HDMI display devices using only one HDMI cable.

Initial Setup

The VS482B supports dual HDMI outputs for HDTVs and/or audio/video receiver (AVR) applications, as shown in the following diagram.

HDMI Sources

VS482B or

Audio Output or

HDMI Displays

The audio/video coming from the HDMI sources (Blu-ray, DVD, etc.) are received by the VS482B and then passed on to the HDMI displays (TV, projector or AVR).

However if the HDMI audio or video is coming from the TV (through a satellite antenna or STB), you can enable ARC so that audio is sent to the AVR/

HDMI receiver through the HDMI cable or the device(s) connected to the

audio output port(s). See p. 14 for the diagram.

Note: 1. Without ARC, you must connect another cable, specifically for passing audio, from the TV to the AVR or the device(s) connected to the audio output port(s).

2. The ARC function requires an HDTV built-in ARC function and must be connected to the correct HDMI output port. Check your HDTV’s user manual for this information.

13

VS482B User Manual

Enabling ARC

With ARC enabled, the TV can act as the HDMI source and send audio

“upstream” to the AVR or speakers connected to the HDMI output ports of the

VS482B.

Note: The HDMI output port 1 is also the ARC input port, depending on

whether the ARC feature is enabled or disabled. See ARC Commands , page 24 for more information.

In the following diagram, audio from the TV goes to the VS482B through the

ARC Input port, and is then passed on to the AVR via the HDMI cable or the audio devices connected to the HDMI output ports. A user can also connect to an audio device (receiver) using an optical or coaxial audio connector.

VS482B

ARC input port

Satellite

STB etc.

Audio output

Audio/Video Receiver

(HDMI output port 2)

No need for another cable for audio

Note: 1. The scenario above works only if the TV supports HDMI and has

ARC enabled.

2. The ARC LED (blue) lights up to indicate that the ARC function is enabled. There is no audio output if your HDTV does not support

ARC function or if the ARC function is not enabled.

14

IR Command Code

1

2

5

6

7

 Carry Frequency: 38KHz

 IR Protocol: NEC

 Customer Code: 00FD

 Data Code:

Function

Up

Left

Down

Right

Setup

ON

OFF

Port 1

Port 2

Port 3

Port 4

MENU

Info

ARC

HDMI MUTE

07

08

09

1B

04

05

06

1E

Data Code

10

1D

02

0C

19

12

0E

8

9

3

4

Chapter 3. Operation

15

VS482B User Manual

RS-232 Serial Interface

The VS482B’s built-in bi-directional RS-232 serial interface allows system control through a high-end controller, PC, and/or home automation / home theater software package.

Configuring the Serial Port

The controller’s serial port should be configured as follows:

Baud Rate

Data Bits

Parity

Stop Bits

Flow Control

19200

8

None

1

None

Switch Port Commands

These actions can also be performed by keying the command into the text box, and clicking Send .

The formula for Switch commands is as follows:

Switch Command + Input Command + Port number [Enter]

1. For example, to switch input port to port 02, type the following: sw i02 [Enter]

2. To switch to the next port, input the following: sw + [Enter]

3. To turn off video output, type the following: sw + off [Enter]

The following tables show the possible values for the Switch Port string:

Command sw

Description

Switch command

Input Command i

Description

Input command

16

Chapter 3. Operation

Port number xx

Description

01-04 port (default is 01)

Control on off

+

-

Description

Turn on the display

Turn off the display

Next Port

Previous Port

The following table shows the available command list:

Command Input Port Control Enter sw i xx

Description

[Enter] Switch Input Port sw on off

[Enter] Turn on (Display out)

[Enter] Turn off (No output) sw +

-

[Enter] Switch to the next input

[Enter] Switch to the previous input

Note: 1. Each command string can be separated with a space.

2. The Port Number command string can be skipped, and the default value will be used.

17

VS482B User Manual

Standby/Power Commands

The Standby/Power feature enables the VS482B to enter power saving mode.

The formula for Standby/Power commands is as follows:

Standby + Control command [Enter]

1. For example, to disable the Standby/Power feature, input the following: standby off [Enter]

The following tables show the possible values for the Standby string :

Command standby

Description

Standby/Power command

Control on off

Description

Turn on power saving mode

Turn off power saving mode

The following table shows the available command list:

Command Control standby on standby off

Enter

[Enter]

[Enter]

Description

Power saving mode on

Power saving mode off

18

Chapter 3. Operation

Switch Mode Commands

You can choose how the VS482B behaves when a new input source is connected to it. By default the Next switch mode setting is enabled. Use the commands below to select a different mode. There are three Switch Modes:

Next - Switch priority is placed on the next port that has a new source device connected to it (default).

Default - The switch behaves normally without automatic switching.

Auto - Places priority on a selected port so that when a source is connected to the said port, the VS482B automatically switches to it, and the port can not be changed until the source is unplugged or auto switching mode is disabled with the default command.

In addition, the Go To function enables the VS482B to switch to the next port with a powered on source device when the current input source device is powered off.

The formula for Switch Mode commands is as follows:

Switch Command + Input Command + Port Number + Control +

[Enter]

1. For example, to enable auto switching for port 02, type the following: swmode i02 auto [Enter]

2. To enable the auto switch next mode, type the following: swmode next [Enter]

3. To turn auto switching off, type the following: swmode default [Enter]

4. To enable the Go To function, type the following: swmode goto on [Enter]

The following tables show the possible values for the Switch Mode string:

Command swmode

Description

Switch Mode command

Input Command i

Description

Input command

Port number xx

Description

01-04 port (default is 01)

19

VS482B User Manual

Control default next auto goto on goto off

Description

No automatic switching operation

Priority is placed on the next port that has a new source connected to it (default)

Priority is placed on a selected port

Switch to the next port with a powered on source device when the current input source is off

Disable Go To function

The following table shows the available command list:

Command Input Port Control Enter swmode i xx default

Description

[Enter] Use Default switch mode swmode next auto

[Enter] Use Next switch mode

[Enter] Use Auto switch mode goto on [Enter] Enable Go To function goto off [Enter] Disable Go To function

20

Chapter 3. Operation

EDID Commands

Extended Display Identification Data (EDID) is a data format that contains a display's basic information and is used to communicate with the video source/ system. You can set up which EDID mode the VS482B uses with the following command:

EDID Command + Control (port1 / auto / default) [Enter]

1. For example, to use the Port1 EDID setting, type the following: edid port1 [enter]

The following tables show the possible values for the EDID string:

Command edid

Description

Enable EDID selection

Control port1 remix default

Description

Implement the EDID of the connected display to Port 1, and pass it to the video source

Implement the EDID of all connected displays. The

VS482B uses the best resolution for all displays.

Implements ATEN’s default

EDID (default).

The following table shows the available command list:

Command Control edid port1 edid edid remix default

Enter

[Enter]

[Enter]

[Enter]

Description

The EDID from Port 1 is passed to the video source

The VS482B implements the EDID of all connected displays and uses the best resolution for all displays (default)

ATEN’s default EDID is passed to the video source

21

VS482B User Manual

CEC Commands

Consumer Electronics Control (CEC) allows interconnected HDMI devices to communicate and respond to one remote control. The formula for CEC mode selection commands is as follows:

CEC Command + Control (Off / Auto / Port1) [Enter]

1. For example, to use the Port1 CEC setting, type the following: cec port1 [enter]

The following tables show the possible values for the Standby string:

Command cec

Description

Enable CEC selection

Control off auto port1

Description

Disable CEC (default)

Apply the video source’s CEC to all display output

Apply the video source’s CEC only to port 1

The following table shows the available command list:

Command Control cec off cec auto cec port1

Enter

[Enter]

[Enter]

[Enter]

Description

CEC off (default)

Connect the video source’s CEC with all display output

Apply the video source’s CEC only to port

1

22

Chapter 3. Operation

Mute Commands

Enable or disable audio coming from the output port(s) using the following command:

Mute Command + Control (On / Off) [Enter]

1. For example, to mute the audio, type the following: mute on [enter]

The following tables show the possible values for the Mute string :

Command mute

Description

Enable / Disable audio of HDMI output port

Control on off

Description

Mute on; audio from HDMI output port is disabled

Mute off; audio output enabled

(default)

Note: Each command string can be separated with a space.

The following table shows the available command list:

Command Control mute on mute off

Enter

[Enter]

[Enter]

Description

Mute on (no audio)

Mute off (audio out)

23

VS482B User Manual

ARC Commands

Audio Return Channel (ARC) allows a source device (TV, STB, etc.) to send audio “upstream” to an audio/video receiver using only one HDMI cable. The formula for enabling/disabling ARC is as follows:

ARC Command + Control (On / Off) [Enter]

1. For example, to enable ARC, type the following: arc on [enter]

The following tables show the possible values for the ARC string:

Command arc

Description

Enable / Disable ARC

Control on

Description

ARC on; output audio passes from HDMI output port 1 to HDMI output port

ARC is disabled (default) off

The following table shows the available command list:

Command Control arc arc on off

Enter

[Enter]

[Enter]

Description

ARC on

ARC off

24

Chapter 3. Operation

Echo

The Echo function lets the VS482B perform front panel and IR control operations, but not commands received through the RS-232 interface.

The formula for the Echo command is as follows:

Echo Command + Control (on/off) + [Enter]

1. For example, to enable the Echo function, type the following: echo on [enter]

The following tables show the possible values for the Echo string:

Command echo

Description

Enable / Disable Echo function

Control on off

Description

Echo function on

Echo function off (default)

The following table shows the available command list:

Command Control echo echo on off

Enter

[Enter]

[Enter]

Description

Echo on

Echo off

Reset

You can reset the VS482B to default factory settings. The formula for the Reset command is as follows:

Reset Command [Enter]

The following tables show the possible values for the Reset string :

Command reset

Description

Reset the device settings

The following table shows the available command list:

Command reset

Enter

[Enter]

Description

Reset the device settings

25

VS482B User Manual

Baud Rate Setting

You can select the RS-232 Baud Rate you want the VS482B to use. Options are 9600, 19200 (default) 38400 and 115200.

The formula for Baud Rate setting command is as follows:

Baud Command + Control [Enter]

1. For example, to select 38400 as your baud rate, type the following: baud 38400 [enter]

The following tables show the possible values for the Baud Rate string

Command baud

Description

Sets the RS-232 baud rate

Control

9600

19200

38400

115200

Description

Use 9600 baud rate

Use 19200 baud rate

Use 38400 baud rate

Use 115200 baud rate

The following table shows the available command list:

Command baud

Control

9600 / 19200 / 38400 /

115200

Enter

[Enter]

Description

Sets the RS-232 baud rate

26

Chapter 3. Operation

Verification

After entering a command, a verification message appears at the end of the command line as follows:

 Command OK - indicates that the command is correct and successfully performed by the switch

 Command incorrect - indicates that the command has the wrong format and/or values.

Powering Off and Restarting

If you power off the VS482B, follows these steps before powering it on again:

1. Power off the attached devices.

2. Unplug the power adapter cable from the VS482B.

3. Wait 10 seconds, and then plug the power adapter cable back in.

4. After the VS482B is powered on, power on the attached devices.

27

VS482B User Manual

OSD Menu

Use the MENU pushbutton on the remote control to view the OSD menu and

cycle through the options in the order shown in the table below. See IR Remote

Control , page 6 for details on how to use the remote control.

Menu Page

Input Setting HDMI 1

HDMI 2

Sub-Menu Page(s)

HDMI device / Blu-ray player / DVD player /

Game Console / Set Top Box / Portable Device

/ PC

HDMI device / Blu-ray player / DVD player /

Game Console / Set Top Box / Portable Device

/ PC

HDMI 3

HDMI 4

HDMI device / Blu-ray player / DVD player /

Game Console / Set Top Box / Portable Device

/ PC

HDMI device / Blu-ray player / DVD player /

Game Console / Set Top Box / Portable Device

/ PC

Audio Setting ARC

Audio Channel

Disable

AUTO

/ Enable

/ Stereo / 5.1 Channel

HDMI Audio Output On / Off

OSD Setting Message Display

Mode

Transparency

Channel / Full / Off

0 ~100 (default is 75 )

System Setting EDID

CEC

Reset to Default

Version

Default / Port1 / Remix

Off / Auto / Port1

On / Off

Version Number

Note: 1. The highlighted texts indicate the VS482BB’s default setting.

2. The OSD function is disabled while 3D content is being displayed.

Switch to 2D content or a different input port to enable the OSD.

28

Chapter 3. Operation

Input Setting Menu

Use this screen to select the video source device(s) for the HDMI input port(s).

1. Use the drop-down menu to select a video source device for HDMI 1 input port. Options are as follows.

Note: The default value HDMI Device does not point to any device. It means there is no video source selected for that HDMI input port.

2. Do the same for HDMI 2, HDMI 3 and HDMI 4 input ports.

29

VS482B User Manual

Audio Setting

Use this screen to configure the VS482B audio settings.

1. Use the drop-down menu to Enable or Disable ARC on the VS482B.

See Audio Return Channel (ARC) , page 13 for more details on this feature.

2. Use the drop-down menu to select which audio channel receiver the

VS482B uses. The default value is Auto .

3. Use the drop-down menu to turn on/off the audio coming from the HDMI output port(s). Select On to enable audio from the active HDMI output port, and select Off to disable it.

30

OSD Setting

Use this screen to configure the VS482B OSD settings.

Chapter 3. Operation

1. Use the drop-down menu to select which display mode the VS482B uses to display information in the upper left corner of the screen. Options are as follows.

 Channel - This shows the source port number.

 Full

- This shows the source port number and source type. See Input

Setting Menu , page 29 for the list of source types.

 Off - There is no information shown.

31

VS482B User Manual

2. Select the visibility of the OSD menu when it is invoked. Press the menu button to enter the adjustment menu. Use the drop-down menu to select a value. The value 100 shows a fully visible and opaque OSD menu. The default value is 85 .

32

System Setting

Use this screen to configure the VS482B system settings.

Chapter 3. Operation

1. Use the drop-down menu to set up which EDID mode the VS482B uses.

See Verification , page 27 for more details.

2. Use the drop-down menu to select how the video source’s CEC is applied.

See Verification , page 27 for more details.

3. Set this to On to have the VS482B return to default settings when it is reset. Otherwise, select Off .

4. This read-only field shows the firmware version of the VS482B.

33

VS482B User Manual

This Page Intentionally Left Blank

34

Chapter 4

The Firmware Upgrade Utility

Introduction

The purpose of the Windows-based Firmware Upgrade Utility is to provide an easy process for upgrading the VS482B. The program comes as part of a

Firmware Upgrade Package that is specific for each device.

As new firmware versions become available, new firmware upgrade packages are posted on our website. Check the website regularly to find the latest information and packages.

Downloading the Firmware Upgrade Package

To download the firmware upgrade package:

1. On our Website go to: Download - Firmware and choose the device model, or from the VS482B product page under the Resources tab, select

Firmware . A list of available firmware upgrade packages appears.

2. Choose the firmware upgrade package that you wish to install (usually the most recent) and download it to your computer.

35

VS482B User Manual

Preparation

To prepare for the firmware upgrade, do the following:

1. Use an RS-232 cable to connect a COM port on your computer to the RS-

232 Serial Port of your VS482B.

VS482B

2. Unplug the VS482B’s power adapter.

3. Hold-down front panel pushbutton 1 and plug the power adapter into the

VS482B to power the unit.

4. If successful, the port 1 LED will start flashing and you can start the upgrade process as explained on the next page.

36

Chapter 4. The Firmware Upgrade Utility

Starting the Upgrade

To upgrade the firmware:

1. Run the downloaded firmware upgrade package file either by doubleclicking the file icon, or by opening a command line and entering the full path to it.

The Firmware Upgrade Utility welcome screen appears:

Note: The screens shown in this section are for reference only. The wording and layout of the actual screens put up by the Firmware

Upgrade Utility may vary slightly from these examples.

2. Read and Agree to the License Agreement (click the I Agree radio button).

37

VS482B User Manual

3. Click Next to continue. The Firmware Upgrade Utility main screen appears. The devices capable of being upgraded are listed in the Device

List panel:

4. Click Next to perform the upgrade. The Port LEDs 1, 3, and 4 will flash while the upgrade is in process.

If you enabled Check Firmware Version , the Utility compares the device's firmware level with that of the upgrade files. If it finds that the device's version is higher than the upgrade version, it brings up a dialog box informing you of the situation and gives you the option to continue or cancel.

38

If you didn't enable Check Firmware Version , the Utility installs the upgrade files without checking whether they are a higher level, or not.

Status messages appear in the Status Messages panel, and the progress toward completion is shown on the Progress bar.

Chapter 4. The Firmware Upgrade Utility

Upgrade Succeeded

After the upgrade has completed, all port LEDs will stop flashing and a screen appears to inform you that the procedure was successful:

Click Finish to close the Firmware Upgrade Utility .

Upgrade Failed

If the Upgrade Succeeded screen doesn't appear, it means that the upgrade failed to complete successfully. See the next section, Firmware Upgrade

Recovery , for how to proceed.

39

VS482B User Manual

Firmware Upgrade Recovery

There are three conditions that call for firmware upgrade recovery:

 When a firmware upgrade is manually aborted.

 When the mainboard firmware upgrade fails.

 When the I/O firmware upgrade fails.

To perform a firmware upgrade recovery, do the following:

1. Power off the device.

2. Connect the RS-232 cable to the RS-232 Serial Port .

3. Repeat the upgrade procedure.

40

Appendix

Safety Instructions

General

 Read all of these instructions. Save them for future reference.

 Follow all warnings and instructions marked on the device.

 This product is for indoor use only.

 Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result.

 Do not use the device near water.

 Do not place the device near, or over, radiators or heat registers.

 The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered.

 The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided.

 Never spill liquid of any kind on the device.

 Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

 The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.

 To prevent damage to your installation it is important that all devices are properly grounded.

 The device is equipped with a DC adapter. This is a safety feature.

 Position system cables and power cables carefully; Be sure that nothing rests on any cables.

 Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock.

 Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.

41

VS482B User Manual

 If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair.

 Liquid has been spilled into the device.

 The device has been exposed to rain or water.

 The device has been dropped, or the cabinet has been damaged.

 The device exhibits a distinct change in performance, indicating a need for service.

 The device does not operate normally when the operating instructions are followed.

 Only adjust those controls that are covered in the operating instructions.

Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.

42

Appendix

Rack Mounting

 Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack.

 Always load the rack from the bottom up, and load the heaviest item in the rack first.

 Make sure that the rack is level and stable before extending a device from the rack.

 Use caution when pressing the device rail release latches and sliding a device into or out of a rack; the slide rails can pinch your fingers.

 After a device is inserted into the rack, carefully extend the rail into a locking position, and then slide the device into the rack.

 Do not overload the AC supply branch circuit that provides power to the rack. The total rack load should not exceed 80 percent of the branch circuit rating.

 Make sure that all equipment used on the rack – including power strips and other electrical connectors – is properly grounded.

 Ensure that proper airflow is provided to devices in the rack.

 Ensure that the operating ambient temperature of the rack environment does not exceed the maximum ambient temperature specified for the equipment by the manufacturer.

 Do not step on or stand on any device when servicing other devices in a rack.

43

VS482B User Manual

Technical Support

International

 For online technical support – including troubleshooting, documentation, and software updates: http://support.aten.com

 For telephone support, see Telephone Support , page iii:

North America

Email Support

Online Technical

Support

Telephone Support

Troubleshooting

Documentation

Software Updates [email protected]

http://www.aten-usa.com/support

1-888-999-ATEN ext 4988

When you contact us, please have the following information ready beforehand:

 Product model number, serial number, and date of purchase

 Your computer configuration, including operating system, revision level, expansion cards, and software

 Any error messages displayed at the time the error occurred

 The sequence of operations that led up to the error

 Any other information you feel may be of help

44

Appendix

Specifications

Function

Display Connections

Connectors Video Input Interfaces

Impedance

Max.

Distance

Video Output Interfaces

Impedance

Max.

Distance

Optical Audio

Coaxial Audio

Stereo Audio

RS-232 Port

Switches

LEDs

EDID Settings

IR Control

Power

IR Extension Port

Port Switch

Mode Selection

Power Button

Input

Audio

Power

VS482B

2

4 x HDMI Type A Female (Black)

100 Ώ

3 m (4096 x 2160 @ 60Hz, 4:4:4)

2 x HDMI Type A Female (Black)

100 Ώ

3 m (4096 x 2160 @ 60Hz, 4:4:4)

1 x Toslink (Black)

1 x RCA (Orange)

2 x RCA (Red / White)

1 x DB-9 Female (Black)

Function: Port Switching & Firmware

Upgrade

Baud Rate: 19200, Data Bits: 8, Stop Bits:

1, Parity: No, Flow Control: No

1 x DC Jack

1 x Mini Stereo Jack Female (Black)

Pushbutton x 4 (HDMI In)

Pushbutton x 1 (ARC ON / OFF)

Pushbutton x 1 (Power ON / OFF)

4 x HDMI In (Green)

1 x ARC ON / OFF (Green)

1 x Power ON / OFF (Green / Orange)

EDID Mode: Default (4K @ 60Hz) / Port-1

/ Remix

1 x IR Receiver

45

VS482B User Manual

Video

Function

Max. Data Rate

Max. Pixel Clock

Compliance

Max. Resolution

Max. Distance

Power Consumption

Environment Operating Temperature

Storage Temperature

Physical

Properties

Humidity

Housing

Weight

Dimensions (L x W x H)

VS482B

18 Gbps (6Gbps Per Lane)

600 MHz

HDMI (3D, Audio Return Channel, Deep

Color)

HDCP 2.2

Consumer Electronic Control (CEC)

4096 x 2160 / 3840 x 2160 @ 60Hz

(4:4:4)

Up to 3 m (Input / Output)

DC 5V:3.29W:15BTU

0–40ºC

-20–60ºC

0–80% RH, Non-condensing

Metal

2.16 Kg (4.76 lb)

43.72 x 15.88 x 4.40 cm

(17.21 x 6.25 x 1.73 in.)

46

Appendix

Limited Warranty

ATEN warrants its hardware in the country of purchase against flaws in materials and workmanship for a Warranty Period of two [2] years (warranty period may vary in certain regions/countries) commencing on the date of original purchase. This warranty period includes the LCD panel of ATEN LCD

KVM switches . Select products are warranted for an additional year (see A+

Warranty for further details). Cables and accessories are not covered by the

Standard Warranty.

What is covered by the Limited Hardware Warranty

ATEN will provide a repair service, without charge, during the Warranty

Period. If a product is detective, ATEN will, at its discretion, have the option to (1) repair said product with new or repaired components, or (2) replace the entire product with an identical product or with a similar product which fulfills the same function as the defective product. Replaced products assume the warranty of the original product for the remaining period or a period of 90 days, whichever is longer. When the products or components are replaced, the replacing articles shall become customer property and the replaced articles shall become the property of ATEN.

To learn more about our warranty policies, please visit our website: http://www.aten.com/global/en/legal/policies/warranty-policy/

47