GEPON ONU 300Mbps
Wi-Fi Router with
1 PON and 1 Giga Port
DG-GR1310
V1.2
05-01-2021
Copyright
Copyright 2020 by DIGISOL SYSTEMS LTD. All rights reserved.
Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without written consent from the company.
Trademarks:
are the property of the respective manufacturers.
Overview
1:1 Product Description
DG-GR1310 ONU meets telecom operators FTTO (office), FTTD (Desk),
FTTH (Home) broadband speed, SOHO broadband access, video surveillance and other requirements and design an EPON Gigabit Ethernet products. It is based on mature and stable, cost-effective EPON technology, high reliability, easy management, configuration flexibility and good quality of service (QoS) guarantees to meet the technical performance of the module IEEE802.3ah.
Figure 1 1GE + WiFi
1:2 Application Chart
Figure 2
1:3 Technical Parameters
Technical item
PON interface
Wavelength
Optical interface
DG-GR1310
1EPON connector, SC single-mode/single-fiber, downlink/uplink 1.25Gbps
Tx1310nm,Rx 1490nm
SC connector
LAN interface
Wireless
LED
1x 10/100/1000Mbps auto adaptive Ethernet interfaces
RJ-45 connector
Compliant with IEEE802.11b/g/n, 300Mbps,
2T2R 1 internal antenna, 1 external antenna
5, For Status of POWER, LOS, PON, LAN, Wi-Fi
Operating condition Temperature: -5°C ~ +55°C
Humidity: 10% ~ 90% (non-condensing)
Storing condition
Power supply
Temperature: -30 °C ~ 60 °C
Humidity: 10% ~ 90% (non-condensing)
DC 12V/0.5A
Power consumption ≤6W
Dimension 120mm×78mm×30mm (L×W×H)
Net weight 0.13Kg
1:4 Package Content
Contents
ONU
Power Adapter
QIG
Quantity
1 PCS
1 PCS
1 PCS
Installation
2:1 Installation Requirements
To avoid equipment damage caused by improper use and personal injury, please observe the following precautions:
● Do not place the device near water or in damp places, in order to
prevent water or moisture from entering the device.
● Do not place the device in an unstable place, avoid falling damage to
equipment.
● Make sure that the supply voltage of the device matches the required
voltage value.
● Do not open the equipment chassis without permission.
● Unplug before cleaning the power plug; prohibit the use of liquid cleaning.
Installation Environment Requirements
ONU equipment must be installed in the interior, and to ensure the following conditions:
● Confirmation at the ONU installation at sufficient space to facilitate
cooling machine.
● ONU suitable operating temperature of 5°C ~55 °C ,
humidity 10% to 90%.
Electromagnetic Environment
ONU equipment in use can be affected by external electromagnetic interferences, such as radiation and conduction through the impact on the device, this should note the following:
● Device workplace should avoid radio transmitters, radar stations, and
high-frequency interference from power equipment.
● Users cable typically require alignment indoors if outdoor lightning
traces measures should.
Equipment Installation
ONU product is a fixed configuration cassette equipment, site equipment installation is relatively simple. Simply install the device on a specified place, connecting the upstream fiber subscriber line connections, connect the power cable. Actual operation is as follows:
1.
Installed on the desktop
Place the machine on a clean bench, this installation is relatively simple, you can observe the following operation:
● Ensure the smooth workbench.
● Around the device enough space for heat dissipation.
● Do not place objects on the device.
2.
Mounted on the wall
● The ONU equipment chasis has two cruciform recess, install two
screws in the wall in accordance to the position of the groove.
● The original selected two mounting screws gently snap into recesses
aligned.
● Slowly let go, so that the device under the support of the screw
hanging on the wall.
2:2 Panel Lights
LED
Power
Optical signal loss
Registration
Interface
WiFi
Mark
Power
LOS
REG
LINK/
ACT
WiFi
Status
On
Off
Blink
Off
On
Off
Description
The device is powered up
The device is powered down
Device does not receive optical signals
Device has received optical signal
The device is registered to the PON system
Device is not registered to the PON system
Blink Device registration is incorrect
Fast Blink Port is sending or/and receiving data
On Port is connected properly (LINK)
Off
Blink
On
Off
Port connection exception or not connected
Port is sending or/and receiving data (ACT)
WiFi running
WiFi not Working
Web Management
EPON ONU provides simple Web management functions, including Device
Information, modify Lan Managemenet IP address, Loid and Password,
Configuration File backup and restore, firmware upgrade etc...
NOTE:
About More ONU Detail Configurations should be configured via ONU Web.
3:1 Default configuration
The following is the default device configuration information.
●
Local (LAN access) Username: admin / Password: stdONUi0i
● LAN port management IP address: 192.168.1.1/24
3:2 Basic configuration
Figure 3 Web Login
Web login default username: admin , password: stdONUi0i
Figure 4 Device Information
Status Menu displays the current device base Information's. Including
Hardware Version, Software Version, Device Model, Device ID.
Note:
All the device information may be changed, the received device shall prevail.
Figure 5 Modify Loid and Password
LOID Menu displays the current device Loid and Password informations.
Loid: 0-24 bytes.
Password: fixed 10 bytes.
Note:
All the changes take effect in the equipment after the restart
Figure 6 Restore Default
Restore Default: The operation to restore the device to its factory configuration.
Note:
1. Press RST button over 10 seconds, onu can restore factory defaults and reboot.
Figure 7 Upgrade
Firmware upgrade Menu displays the current equipment upgrades related information.
Figure 8 Backup/ Restore Configuration
Download: The operation to backup configuration from the device.
Upload : The operation to restore configuration from a configuration file.
Troubleshooting
1. After power all the lights are lit?
Reasons:
1) Power connection errors
2) Power is not normal.
Solution:
1) Check that the power cable is connected
2) The rear panel of the power supply is turned on.
2. GE / FE led does not light?
Reasons:
1) Network cable is damaged or loose connection
2) Cable type error;
3) Long lines outside the allowable range.
Solution:
1) Replace the network cable, and pay attention to the standard
Ethernet cable must be parallel or crossing lines.
3. After working for some time to stop working?
Reasons:
1) Power supply is not working properly
2) The equipment from overheating.
Solution:
1) Check if there is contact with abnormal voltage is too high or too low;
2) Check the ambient conditions, vents are normal ventilation.
4. LOS led flashes?
Reasons:
1) Fiber failure;
2) Central office equipment failure.
Solution:
1) Inspect fiber is connected properly, is connected to the correct connector, optical power is normal.
2) Contact your operator.
5. PON led flashes?
Reasons:
1) Fiber optic connector is loose;
2) Central office equipment failure;
3) Fiber optic connectors are dust.
Solution:
1) Inspect fiber is connected properly;
2) Cotton ball with alcohol swabbing fiber optic connectors;
3) Contact your operator.
DIGISOL SYSTEMS LIMITED
L-7, Verna Industrial Estate,
Salcete, GOA - 403722 www.digisol.com
Digisol is a Subsidiary of Smartlink Holdings Limited
1800 209 3444 [email protected]
