BOSS BCB-30X Pedal Board Owner Manual

Add to my manuals
1 Pages

advertisement

BOSS BCB-30X Pedal Board Owner Manual | Manualzz

BCB-30X

Pedal Board Owner’s Manual

English Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the document(s) where it will be available for immediate reference.

Effect Unit Installation Examples

By cutting the included holding pad to match the shape of the products that you want to install, you can hide the cabling and create a clean layout.

Example 1 Example 2 Example 3

Do It Yourself 1 (Cutting the Holding Pad)

When installing stompboxes, you can save layout time by using the existing pre-cuts in the holding pad to remove unneeded portions.

The cutouts at the left and right of the holding pad indicate the positions that are above the cable guides

(places to conceal long cables) when it is placed in the case. Use these cutouts when deciding where to position your effect units, and cut the holding pad so that cables can be accommodated neatly when the effect units are installed.

* If you use a knife to cut the holding pad, take care not to injure yourself.

* When cutting the cutouts, take care not to damage nearby equipment with the knife.

Cutouts

Holding pad

Making Connections

Cable guide

For details on the BCB-30X, refer to the Boss website.

https://www.boss.info/global/ products/bcb-30x/

For BOSS cables, refer to the BOSS website (Accessories).

https://www.boss.info/global/ categories/accessories/boss_cables/

Do It Yourself 2 (Keeping the Cables Neat)

If the power supply parallel cable and long patch cables are aligned with the cable guide, the cables can be managed neatly.

Cable guide

MEMO

To detach the lid, lift it to the position shown in the illustration, and then press in the direction of the arrow.

USING THE UNIT SAFELY

About WARNING and CAUTION Notices

Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.

Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.

* Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.

About the Symbols

The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled.

The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power-cord plug must be unplugged from the outlet.

WARNING

Do not disassemble or modify by yourself

Do not carry out anything unless you are instructed to do so in the owner’s manual. Otherwise, you risk causing malfunction.

Do not repair or replace parts by yourself

Be sure to contact your dealer, a

Roland service center, or an official

Roland dealer.

For a list of Roland service centers and official Roland dealers, refer to the Roland website.

Do not place in an unstable location

Otherwise, you risk injury as the result of the unit toppling over or dropping down.

ALWAYS OBSERVE THE FOLLOWING

WARNING

Do not use or store in the following types of locations

• Subject to temperature extremes

(e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are

• Damp (e.g., baths, washrooms, on wet floors); or are

• Exposed to steam or smoke; or are

• Subject to salt exposure; or are

• Exposed to rain; or are

• Dusty or sandy; or are

• Subject to high levels of vibration and shakiness; or are

• Placed in a poorly ventilated location.

Be cautious to protect children from injury

Always make sure that an adult is on hand to provide supervision and guidance when using the unit in places where children are present, or when a child will be using the unit.

WARNING

Do not drop or subject to strong impact

Otherwise, you risk causing damage or malfunction.

CAUTION

Avoid climbing on top of the unit, or placing heavy objects on it

Otherwise, you risk injury as the result of the unit toppling over or dropping down.

Take care so as not to get fingers pinched

When handling the following moving parts, take care so as not to get fingers, toes, etc., pinched.

Whenever a child uses the unit, an adult should be on hand to provide supervision and guidance.

• Lid

• If you use a knife to cut the holding pad, take care not to injure yourself.

• When trimming the cutouts, take care that the knife does not damage nearby devices.

Placement

• Depending on the material and temperature of the surface on which you place the unit, its rubber feet may discolor or mar the surface.

Maintenance

• Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.

IMPORTANT NOTES

Additional Precautions

• When disposing of the packing carton or cushioning material in which this unit was packed, you must observe the waste disposal regulations that apply to your locality.

• When opening/closing the lid, please be careful not to get your fingers pinched between the movable part and the unit. In places where small children are present, make sure that an adult provides supervision and guidance.

Intellectual Property Right

• Roland, BOSS are either registered trademarks or trademarks of Roland

Corporation in the United States and/or other countries.

• Company names and product names appearing in this document are registered trademarks or trademarks of their respective owners.

For EU Countries

Manufacturer: Roland Corporation

2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN

Importer: Roland Corporation

ENA 23 Zone 1 nr. 1620 Klaus-Michael Kuehnelaan 13, 2440 Geel, BELGIUM

For EU Countries

* To prevent malfunctions or speaker damage, be sure to minimize the volume of all devices and power them off before you make connections.

* After you have made connections correctly, you must observe the following procedure when turning on the power

Malfunctions or speaker damage might occur if you fail to observe the correct order.

When turning the power on: Power-on the amp last.

When turning the power off: Power-off the amp first.

Main Specifications

Dimensions

Inside dimensions

Weight

Accessories

Option

(sold separately)

330 (W) x 307 (D) x 100 (H) mm

13 (W) x 12-1/8 (D) x 3-15/16 (H) inches

66 (H) mm

2-5/8 (H) inches

1.3 kg

2 lbs 14 oz

4-pin parallel DC cable x 1

Pre-cut insert pad (thickness: 10 mm) x 1

Owner’s Manual

AC adaptor: PSA series

Pre-cut insert pad (thickness: 10 mm)

* This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website.

© 2020 Roland Corporation

1

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Questions and Answers

What are the dimensions of the Boss BCB-30X?
The dimensions of the Boss BCB-30X are 13 (W) x 12-1/8 (D) x 3-15/16 (H) inches, or 330 (W) x 307 (D) x 100 (H) mm.
What accessories come with the Boss BCB-30X?
The Boss BCB-30X comes with a pre-cut insert pad (thickness: 10 mm), a 4-pin parallel DC cable, and an owner's manual.
What is the weight of the Boss BCB-30X?
The Boss BCB-30X weighs 2 lbs 14 oz, or 1.3 kg.
What is the power supply for the Boss BCB-30X?
The Boss BCB-30X uses an AC adaptor from the PSA series (sold separately).
What are some precautions to take when using the Boss BCB-30X?
Do not use or store the Boss BCB-30X in extreme temperatures, damp or dusty areas, or areas exposed to salt, steam, smoke, or high levels of vibration. Avoid climbing on top of the unit or placing heavy objects on it. Be cautious of moving parts and sharp edges.
How do I make connections to the Boss BCB-30X?
To make connections to the Boss BCB-30X, first ensure that all devices are powered off and the volume is minimized. Connect the power supply and any necessary cables, and then power on the devices in the following order: first the effects units, then the amp.

Related manuals

Download PDF

advertisement