MyBinding Morgana BM61 User Manual
MyBinding Morgana BM61 is a booklet maker that combines features from large and advanced systems into one compact unit. It can be installed against a collator/feeder or run as a stand-alone unit. The BM61 can staple and fold or just fold a variety of paper sizes and types, making it ideal for creating booklets, brochures, and other printed materials.
Advertisement
Advertisement
Morgana BM61 Booklet
Maker with Side
Jogging Unit
Instruction Manual
Booklet Maker BM 61
Operator Manual
Doc No. T10185
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Morgana Systems Limited ▪ United Kingdom ▪ www.morgana.co.uk ▪ Telephone: ( 01908 ) 608888 ▪ Facsimile: ( 01908 ) 692399
BOOKLET MAKER BM 61
Operating Instruction
Booklet Maker Reference
Part no: 61255
Doc no: T10185
Rev. date: 5 Apr 2013
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Safety Information
When using this machine, following safety precautions should always be followed.
Notation conventions
Whenever necessary, the following points for attention are indicated in this manual.
WARNING:
Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.
CAUTION:
Indicates a potentiality hazardous situation which, if instructions are not followed, may result in minor or moderate injury or damage to machine or property.
Note
This sign refers to:
• Remarks for making the operation much easier. You get practical hints or knowledge to assist you in the machine operation such as:
• Preparations required before operating
• How to prevent papers from being misfed or damaged
• Precautions required or actions to take after misoperation
• Limitations like numerical limits, functions that cannot be used together or conditions, under which a particular function cannot be used or obtained.
• Information.
[ ]
Keys that appear on the machine’s display panel.
Safety during operation
WARNING:
• Always connect the equipment to a properly grounded power source (wall outlet). If in doubt, have the power source checked by a qualified electrician.
• Improper grounding of the equipment can result in electrical shock.
• To avoid hazardous electric shock, do not remove any covers or screws other than those specified in this manual.
• Turn off the power and disconnect the power plug (by pulling the plug, not the cable) if any of the following conditions exists:
• You drop objects or spill something into the equipment.
• You suspect that your equipment needs service or repair.
• Your equipment’s covers has been damaged.
• You notice unusual noises or odours when operating the equipment.
• If the power cable or plug becomes worn out or otherwise damaged
• Before cleaning and care.
• Before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equiment
• This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
• The product (System) which is connected to this machine will be class A.
Note
The domestic environment is an environment where the use of broadcast radio and television recievers may be expected within a distance of 10 m of the apparatus concerned.
TABLE OF CONTENTS
What You Can Do With This Machine ............................................................................................ 5
Main Components ........................................................................................................................... 6
1. Basics ............................................................................................... 11
2. Settings ............................................................................................ 13
3. Operation.......................................................................................... 17
4. Troubleshooting .............................................................................. 19
5. General remarks .............................................................................. 21
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Page Intentionally Blank
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
What You Can Do With This Machine
BM 61 stand alone unit
BM 61 against a collator/feeder 510
The BM 61 automatic Booklet Maker combines features from large and advanced systems into one compact unit designed to meet the highest demands for productivity, safety and ease of operation .
The BM 61 can be installed against a collator/feeder or run as a stand alone unit. The bookletmaker can be installed against ’s collator model 310/306 or against collator/feeder model 510.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
5
Main Components
General
1 2
3
4
5
6
6
1. Top cover
2. Upper pressure roller assembly
3. Press area, machine release
4. Control panel
5. Fold stop assembly
6. Stacker
(Only used for ON-line operation to Collator)
(Press here and the Booklet Maker will be released from the Collator and can be rolled away)
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Infeed section, upper
1 2 3 4 5 6
11
10
1. Upper guide, side jogger
2. Side jogger, rear
3. Scale, paper length
4. Rear jogger roller
5. Side jogger, front
6. Upper guide, side jogger
7. Release handle, side jogger
8. Scale, paper width
9. Anvil
10. Release handle, side jogger
11. Scale upper pressure roller assembly
9
7
8
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
7
8
Infeed section, upper
1 2
9
8
3
7 6 5 4
1. Positioning holes, small paper width (310/306:Used for A4/8½” paper widths or sizes nearby.
2. Positioning holes, large paper width (310/306: Used for A3/11” paper widths or sizes
3. Positioning mark (green) nearby. 510: Used for all paper sizes)
(Shall correspond to the green mark on the
Collator)
(Used for adjustment to correct paper length) 4. Paper stop crank
5. Rear jogger latch
6. Rear jogger adjustment latch
9. Docking Bracket
(Used to lower the rear jogger and enable
OFF-line
(Used to position the rear jogger to the paper
7. Receptacle, connection cable length)
(The connection cable from the Collator here)
8. Knob, adjustment for odd paper size (By loosening the knob the Docking Bracket can be individually positioned for odd paper sizes)
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Control Panel
2
0
I
1 3 4 5 6 7 8
1. Power switch
2. Low staples indicator
3. Jam indicator *
4. Stapling ON / OFF
5. Folding ON / OFF
6. Automatic start ON / OFF
Automatic start SAFE MODE/ FAST MODE
7. Time delay
8. Manual start button
(Can only be used OFF-line)
(Can only be used ON-line)
(Can only be used OFF-line)
(Can only be used OFF-line)
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920 9
Accessories (optional)
3
1 2
4
10
1. Belt Stacker
2. Adapter
3. Delivery Tray
4. Knob, Delivery Tray (By loosening the knob the Delivery Tray can be adjusted
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
1. Basics
Turning On / Off the Power
Plug the power cord into the wall outlet and into the bookletmaker.
Set power switch (A) to 1 to turn on the power, if power on the green lamp (B) will lit.
To turn off the power set power switch (A) to 0, if power off the green lamp (B) will also be turned off
(B)
(A)
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920 11
12
Paper Settings
Set up for non-standard paper sizes
This procedure is to enable ON-line operation with paper sizes that deviate from the standard
A4/A3 and 81/2“x11”/11”x17” sizes.
1.
Perform the setup of the Booklet Maker for the paper size.
2.
Attach the Booklet Maker to the Collator, using the positioning holes on tBookletMaker that best matches the paper size. (Green mark on rear side jogger as close as possible to the Docking Bracket).
3.
Loosen the knob for adjustment to odd paper sizes on the Docking Bracket.
4.
Move the Booklet Maker sidewise until the green mark on the rear side jogger is aligned with the green mark on the Collator.
5.
Tighten the knob.
Reset to standard paper sizes
1.
Disconnect the Booklet Maker from the Collator by pressing the Docking Bracket
(green marked side).
2.
Loosen the knob for adjustment to odd paper sizes.
3.
Slide the Docking Bracket back to align it with the chassis in the Booklet Maker, it will lock into place.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
2. Settings
ON-line
Stapling and folding
1.
Open the top cover.
2.
Set the two side joggers to the correct paper size according to the scale.
3.
Insert a set to the stapling area.
4.
Move the rear side jogger up against the paper to verify that the side jogger aligns the sheets.
Note
When checking the alignment, do not squeeze the release handle, only push on top ofthe side jogger at the green label, to simulate the jogging action that the BM 61 does during run.
5.
Turn the paper stop crank until the trail edge of the set is in line with the scale for paper length.
6.
Move the rear jogger up against the trail edge of the set.
7.
Remove the set.
8.
Position the upper pressure roller according to the scale.
9.
Position the stapler heads over the anvils to be used.
10. Attach the Booklet Maker to the Collator and make sure that the green mark on the
Docking Bracket aligns with the green mark on the Collator.
11. Set the stapling switch to ON position.
12. Set the folding switch to ON position.
13. Close the top cover.
14. Set the power switch to ON position.
Folding only
1. Same procedure as above with the exception that on point 11 the switch is set to OFF position and point 9 is not performed.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
13
14
OFF-line
Stapling and folding
1.
Remove the upper pressure roller assembly.
2.
Flip over the side jogger upper guides (both side joggers).
3.
Lower the rear jogger unit by pressing the rear jogger unit forward and downwards
(green marked).
4.
Open the top cover.
5.
Set the side jogger to the correct paper size according to the scale.
6.
Insert a set into the stapling area.
7. Move the rear side jogger up against the paper to verify that the side jogger aligns the sheets.
Note
When checking the alignment, do not squeeze the release handle, only push on top of the side jogger at the green label, to simulate the jogging action that the BM 61 does during run.
8.
Turn the paper stop crank until the trail edge of the set is in line with the scale for paper length.
9.
Remove the set.
10. Position the stapler heads over the correct anvils.
11. Set the stapling switch to ON position.
12. Set the folding switch to ON position.
13. Close the top cover.
14. Set the power switch to ON position.
Folding
1.
Same procedure as the last one, with the exception that on point 11 the switch is set to OFF position and point 10 is not performed.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
4.1.5 Block stapling - Option 1
1.
Lower the rear jogger by pressing the rear jogger unit forward (green marked).
2.
Remove the upper pressure roller assembly.
3.
Flip over the side jogger upper guides (both side joggers).
4.
Open the top cover.
5.
Set the side jogger to the correct paper size according to the scale.
6.
Insert a set into the stapling area.
7.
Move the rear side jogger up against the paper to verify that the side jogger aligns the sheets.
Note
When checking the alignment, do not squeeze the release handle, only push on top of the side jogger at the green label, to simulate the jogging action that the BM 61 does during run.
8.
Turn the paper stop crank to position the set to the stapler.
9.
Remove the set.
10. Position the stapler heads over the correct anvils.
11. Close the top cover.
12. Set the stapling switch to ON position.
13. Set the folding switch to OFF position.
14. Select manual or automatic start.
15. Flip down the fold stop to enable the sets to pass through the machine.
16. Set the power switch to ON position.
Note
By using the adapter (optional) either the Belt Stacker or the Delivery Tray can be used for stacking of stapled sets.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
15
16
4.1.6 Block stapling - Option 2
1.
Lower the rear jogger by pressing the rear jogger unit forward (green marked).
2.
Remove the upper pressure roller.
3.
Flip over the side jogger upper guides (both side joggers).
4.
Open the top cover.
5.
Set the side jogger to the correct paper size according to the scale.
6.
Insert the two red pins in the holes in the side joggers. (The pins are stored inside the machine over the fold rolls). These will stop the set in the correct position (in this mode the set will not be transported through the machine).
7.
Insert set into the stapling area.
8.
Move the rear side jogger up against the paper to verify that the side jogger aligns the sheets.
Note
When checking the alignment, do not squeeze the release handle, only push on top of the side jogger at the green label, to simulate the jogging action that the BM 61 does during run.
9.
Remove the set.
10. Position the stapler heads over the correct anvils.
11. Set the stapling switch to ON position.
12. Set the folding switch to OFF position.
13. Select manual start.
14. Close the top cover.
15. Set the power switch to ON position.
16. To operate insert one set and press the manual start button. When stapled, remove set and insert the next one.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
3. Operation
Operating the bookletmaker
Operating ON-line
1.
Verify that the set up of the Booklet Maker is completed.
2.
Select “third party output” on the Collator.
3.
Press “calibration” on the Collator.
4.
The set will enter the Booklet Maker and remain in the stapling section unstapled.
5.
Verify that the set is completed/correct press the Collator start button.
6.
Select speed with button as shown below. (Only possible with model 510)
High Speed
Safe Mode
Operating OFF-line
1.
Select manual or automatic start.
Manual start: Make sure that the time delay is set to minimum. Press the manual start
button for each operation.
Automatic start:The set will automatically be stapled as it is inserted in the
BookletMaker.
2.
When operating, insert one set at a time. Align the set with your fingertip. When automatic mode is selected, set time delay to allow careful alignment.
Note
The manual start button will light up when the next set may be inserted.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
17
Page Intentionally Blank
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
4. Troubleshooting
Troubleshooting
PROBLEM
Paper jam in fold roller section
Stapler jam
Bad sheet alignment side
Bad sheet alignment front to back
Not possible to select third party eject on
Collator
Paper jam into side guides
Paper jam in infeed area
Set remaining in stapling section
POSSIBLE CAUSES
Folding not selected
Side joggers set too tight
ACTION
Select folding on control panel
Adjust side joggers correctly
Too much material on belt stacker Switch on power, when the green button is lit, push it immediately for reversal feed motion on rolls.
Stapler not aligned with anvils Align staplers with anvil
Side joggers incorrectly adjusted Adjust side joggers to the paper size
Rear jogger incorrectly adjusted
Upper pressure roller missing
Upper pressure roller incorrectly positioned
Connection cable not attached
Top cover open
Power switch set to OFF position
Booklet Maker in jam condition
Booklet Maker incorrectly positioned to Collator
Paper size setting incorrect
Adjust rear jogger
Mount upper pressure roller
Position the upper pressure roller to correct paper size
Attach connection cable
Close top cover
Set power switch to ON position
Clear jam in Booklet Maker
Reposition the Booklet Maker for the correct paper size
Adjust side joggers to the correct paper size
Fold down upper guides Upper guides on side jogger unfolded
Upper pressure roller incorrectly positioned
Rear jogger unit lowered in ONline mode
Lower stapler
Misfeed in Collator
Paper jam in Booklet Maker
Side jogger set too tight
Reposition the pressure roller
Raise the rear jogger
Load stapler
Correct problem in Collator and restart
Clear paper jam
Adjust the side joggers to the correct paper size
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
19
Page Intentionally Blank
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
5. General remarks
Do’s And Don’ts
Always connect the equipment to a properly grounded power source receptacle. When in doubt, have the receptacle checked by a qualified electrician
Warning
• Improper connection of the equipment grounding conductor can result in electrical shock.
• Always follow all warnings marked on, or supplied with, the equipment.
• Always locate the equipment on a solid support surface with adequade strenghth for the weight of the machine.
• Always exercise care in moving or relocating the equipment
• Always keep magnets and all devices with strong magnetic field away from the machine.
• Do not use a ground adapter plug to connect the equipment to a power source receptacle that lacks a ground connection terminal.
• Do not attempt any maintenance function that is not specifically described in this docu mentation.
• Do not remove the covers or guards that are fastened with screws.
• Do not install the unit near a radiator or any other heat source.
• Do not override or “cheat” electrical or mechanical interlock devices.
• Do not operate the equipment if you notice unusual noises or odours. Disconnect the power cord from the power source receptacle and call your customer service engineer to correct the problem.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
21
Placing Your Machine
Machine Environment
• Always locate the equipment on a solid support surface with adequate strength for the weight of the machine.
• Always keep magnets and all devices with strong magnetic fields away from the machine.
If the place of installation is air-conditioned or heated, do not place the machine where it will be:
• Subjected to sudden temperature changes.
• Directly exposed to cool air from an air-conditioner.
• Directly exposed to heat from a heater.
Power Connection
• Always connect the equipment to a properly grounded power source. If in doubt, have the power source checked by a qualified electrician.
Warning
Improper grounding of the equipment can result in electrical shock.
• Never connect the machine to a power source that lacks a ground connection terminal.
22
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
6. Specifications
Technical specification
Capacity
Speed -
Model 510
High
BM 61 (ON-line)
10 sheets 80 gsm (incl. cover)
10 sheets 20 lb bond (incl. cover)
1800 A4 sized booklets/hour
1600 A3 sized booklets/hour
Low 1600 A4 sized booklets/hour
1200 A3 sized booklets/ hour
BM 61 (OFF-line)
22 sheets 80 gsm
22 sheets 20 lb bond
Adjustable up to 1800 A5 or
1400 A4 sized booklets/hour
Speed - Model 310/306
Paper size
Stapler head
Low stapler detection
Jam detection
Jogging
Min
Max
Height
Width
Depth
Weight
Voltage
1600 A4 sized booklets/hour
1400 A4 sized booklets/hour
Adjustable up to 1800 A5 or
1400 A4 sized booklets/hour
200 x 270 mm, 7 7 /
8
” x 10 5 /
8
”
305 x 440 mm, 12” x 17 1 /
4
”
210 chisel point
Yes
Yes
Side and back
550 mm (880 mm incl. base)
21 5 /
8
” (34 5 /
8
” incl. base)
780 mm (1420 mm incl. Belt Stacker)
30 11 /
16
“ (55 7 /
8
“ incl Belt Stacker)
500 mm
19 5 /
16
“
58 kg
128 lb
115 V 60 Hz
230/240 V 50 Hz
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
23
Page Intentionally Blank
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Notes
Notes
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Download
Public link updated
The public link to your chat has been updated.
Document public link
Advertisement
