Universal Bluetooth

®

Headset H560

H560

MOTOMANUAL

1

Figure 1

2

3

4

Figure 2

5

6

1

2

Figure 3

Figure 4 Figure 5

English

European Union Directives Conformance Statement

Hereby, Motorola Inc., declares that this H560 is in compliance with the essential requirements and other relevant provisions of

Directive 1999/5/EC.

You can view your product’s Declaration of Conformity (DoC) to Directive

1999/5/EC (the R&TTE Directive) at www.motorola.com/rtte.

Caring for the Environment by Recycling

When you see this symbol on a Motorola product, do not dispose the product with household waste.

Recycling Mobile Phones and Accessories

Do not dispose of mobile phones or electrical accessories, such as chargers or headsets, with your household waste. In some countries or regions, collection systems are set up to handle electrical and electronic waste items.

Contact your regional authorities for more details. If collection systems aren’t available, return unwanted mobile phones or electrical accessories to any

Motorola Approved Service Centre in your region.

FCC Notice to Users

Users are not permitted to make changes or modify the device in any way.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. See-

47-CFR-Sec.-15.21.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See-47-CFR-Sec.-15.19(3).

3

English

Before you begin

See figure 1 on page 1.

Take a moment before you get started to familiarize yourself with your new

H560 Headset.

1. Volume buttons

2. Speaker

3. Call button

4. Power switch

5. Indicator light

6. Microphone

Charging your headset

See figure 2 on page 1

Verify slide switch is in the off position (toward the charging port).

The indicator light turns red or yellow when the battery is charging. It may take up to 1 minute for the indicator light to turn on. When the headset’s battery is fully charged (about 2 hours), the indicator light turns green.

Note: Headset is not functional while charging.

This product uses a lithium ion, rechargeable, non-replaceable battery.

Your battery is designed to last the life of the product. It should only be removed by a recycling facility. ANY ATTEMPT TO REMOVE OR REPLACE

YOUR BATTERY WILL DAMAGE THE PRODUCT.

4

English

Wearing your headset

See figure 3 on page 2

Your H560 headset is supplied with multiple earbuds. The earbud is fitted onto the end of your headset’s earpiece speaker, and placed onto your ear when using your headset.

Your headset’s performance is greatly dependent upon achieving a good fit on your ear. Therefore, we recommend trying all the supplied earbuds with your headset.

You can wear your H560 headset on your left or right ear. The headset comes ready for the right ear.

Placing the headset on your right ear :

Placing the headset on the left ear :

See figure 4 on page 2

See figure 5 on page 2

Turning headset on and off

To turn ON your headset, slide the switch toward the microphone. The indicator light flashes blue 3 times, then :

UÊÊÊy>ÅiÃʈ˜ÊLÕiÊ>˜`Ê«ÕÀ«iÊ­ˆvÊ«>ˆÀi`Ê>˜`ÊVœ˜˜iVÌi`Ê܈̅Ê>˜œÌ…iÀÊ`iۈVi®°

UÊÊÊLiVœ“iÃÊÃÌi>`ˆÞÊLÕiÊ­ˆvÊÀi>`ÞÊ̜ÊLiÊ«>ˆÀi`®°

To turn OFF your headset, slide the switch toward the charging plug. The indicator light flashes 3 times then turns off.

5

English

Pairing your headset

Your phone’s Bluetooth feature is off by default. To use your headset, turn on the Bluetooth feature in your phone. Please check your phone’s user’s guide.

Note : The Bluetooth feature remains on until you turn the feature off.

Before you can use your headset, you must pair it with your phone.

1 Ensure headset is in pairing mode

Power on headset by sliding the Power switch towards the microphone to initiate easy pairing. After a few moments, the indicator light will be steadily lit in blue to indicate headset is in pairing mode.

If the headset does not enter pairing mode, see “Troubleshooting” for help.

2 Set your phone to look for your headset

UÊÊÊ*iÀvœÀ“Ê >Ê `iۈViÊ `ˆÃVœÛiÀÞÊ vÀœ“Ê ̅iÊ «…œ˜i°Ê œÀÊ `iÌ>ˆÃÊ >LœÕÌÊ `iۈViÊ discovery, consult your phone’s user’s guide. The phone lists Bluetooth devices it finds.

UÊÊÊ-iiVÌÊ Motorola H560 in the list of discovered devices and confirm by following the on-screen prompts.

UÊÊÊ7…i˜Ê«Àœ“«Ìi`ÊLÞÊ̅iÊ«…œ˜i]Êi˜ÌiÀÊ̅iÊ«>ÃÎiÞÊ 0000 and confirm.

Pairing is successful when the headset indicator light changes from steadily lit to flashing blue and purple.

6

English

Test and use

Your phone and headset are now paired and ready to make and receive calls.

To confirm they are successfully paired and operating properly, place the headset over your ear and make a call from your phone. You will hear ringing from the headset.

After you have successfully paired your phone and headset, you do not need to repeat these steps each time you use the headset.

Note: If desired, your headset can be restored to original factory settings.

This action will erase all pairing information stored in your headset. Thus, you will need to pair your phone and headset again. To restore your headset to original factory settings, press and hold both Volume buttons and the Call button at the same time for 10 seconds.

Changing volume button orientation

You can change the orientation of the volume buttons on your headset.

1. Turn the headset power off.

2. Press and hold the Volume button you want to assign as the «volume up» button and slide the switch toward the microphone. The indicator light flashes blue 3 times, then steady blue. When connected, it will flash blue/ purple.

7

English

Using your headset: making & receiving calls

Your headset supports both Hands-free and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone’s user’s guide for more information.

Note: Some features are phone/network dependent.

Function

Receive a call

End a call

Reject a call

Action

Tap the call button

Tap the call button

Press and hold a volume button until the

Make a voice dial call Tap the call button and wait for voice

prompt

Redial last call Press and hold the call button until you hear 2 tones

Answer second incoming call Use phone to answer (follow your phone’s

instructions)

Mute or unmute a call Tap both volume buttons

8

English

Indicator lights

Checking battery level

While your headset is turned on and not on a call, you can check the battery charge level by pressing and holding both Volume buttons. The indicator light displays charge status for 5 seconds. The colour of the light indicates the remaining talk time.

Headset Indicator

Green

Yellow

Red

Available Talk Time

Up to 7 hours

From 2 to 5 hours

Less than 2 hours

To save battery power, turn OFF the headset when you don’t use it for an extended time by sliding the switch towards the charging plug.

Charging status (with charger plugged in)

Headset Indicator

Red

Yellow

Green

Headset Status

Charging (below 50% charge)

Charging (above 50% charge)

Charging complete

9

English

Operating status (with no charger plugged in)

Headset Indicator

Off

3 blue flashes

Steady blue

Rapid blue/purple flashes

Quick blue flash

Slow blue pulse

Slow blue flash

Slow red flash

Slow purple pulse

Steady red

Quick red flash

Headset Status

Power off

Powering on/off

Pairing mode

Connection successful

Incoming/outgoing call

Connected (on a call)

Standby (not on a call)

Idle (not connected to phone)

Connected call muted

Attempting to connect

Low battery

Note: After 20 minutes on a call or of inactivity, the light stops flashing to conserve power, but the headset remains on.

10

English

Audio tones

Audio Tone

Ascending tone

2 descending tones

Ring tone

2 short tones when pressing

Volume button

High/low tones repeated every 60 sec.

No audio indications; deteriorating quality

2 ascending tones

2 rapid ascending tones

2 rapid descending tones

Low tone every 10 seconds

Headset Status

Powering on

Powering off

Incoming call

Volume at minimum or maximum

Low battery

Out of range

Connected to phone

Mute enabled

Mute disabled

Mute reminder

11

English

Troubleshooting

My headset will not enter pairing mode

Make sure that any devices previously paired with the headset are turned off. If the indicator light is not steadily lit in blue, turn off both the other device and headset, wait 10 seconds, then turn headset back on. Wait for the indicator light to become steadily lit in blue, indicating the headset is now in pairing mode.

My phone doesn’t find my headset

Make sure the indicator light on your headset is on (lit in blue) and steady when your phone is searching for devices.

My headset worked before but now it’s not working

Make sure your phone is on, and the Bluetooth feature is turned on in your phone. If Bluetooth was turned off or was turned on only temporarily, you may need to restart it and pair your phone and headset again.

If you have any additional questions, please call your hotline number

(0870-9010-555) or visit us at www.hellomoto.com.

12

motorola.com

MOTOROLA and the Stylized M Logo are registered in the US Patent &

Trademark Office. All other product or service names are the property of their respective owners. The Bluetooth trademark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Motorola, Inc. is under license. © 2007 Motorola, Inc. All rights reserved.

6803578F47 - Printed in the EU.