Eneo DMR-104, DMR-104/Extens Operating Instructions Manual

Add to my manuals
12 Pages

advertisement

Eneo DMR-104, DMR-104/Extens Operating Instructions Manual | Manualzz

eSATA External Storage

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product ’ s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

COMPLIANCE NOTICE OF FCC:

THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL

DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE

REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED

IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO

FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION

MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS

EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE, IN WHICH CASE

USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.

WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE

FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-

CAUSING EQUIPMENT REGULATIONS.

The information in this manual is believed to be accurate as of the date of publication. We are not responsible for any problems resulting from the use thereof. The information contained herein is subject to change without notice.

Revisions or new editions to this publication may be issued to incorporate such changes.

WEEE ( Waste Electrical & Electronic Equipment )

Correct Disposal of This Product

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

i

Operating Instructions

Important Safeguards

ii

1. Read Instructions

All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Cleaning

Unplug this equipment from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.

4. Attachments

Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury.

5. Water and/or Moisture

Do not use this equipment near water or in contact with water.

6. Ventilation

Place this equipment only in an upright position. This equipment has an open-frame Switching Mode Power Supply (SMPS), which can cause a fire or electric shock if anything is inserted through the ventilation holes on the side of the equipment.

7. Placing and Accessories

Do not place this equipment on an unstable cart, stand or table. The equipment may fall, causing serious injury to a child or adult, and serious damage to the equipment.

This equipment and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may cause the equipment and cart combination to overturn.

8. Power Sources

This equipment should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power, please consult your equipment dealer or local power company.

9. Power Cords

Operator or installer must remove power and TNT connections before handling the equipment.

10. Lightning

For added protection for this equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the equipment due to lightning and power-line surges.

11. Overloading

Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.

12. Objects and Liquids

Never push objects of any kind through openings of this equipment as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the equipment.

13. Servicing

Do not attempt to service this equipment yourself. Refer all servicing to qualified service personnel.

14. Damage requiring Service

Unplug this equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A.

When the power-supply cord or the plug has been damaged.

B.

If liquid is spilled, or objects have fallen into the equipment.

C.

If the equipment has been exposed to rain or water.

D.

If the equipment does not operate normally by following the operating instructions, adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the equipment to its normal operation.

E.

If the equipment has been dropped, or the cabinet damaged.

F.

When the equipment exhibits a distinct change in performance – this indicates a need for service.

15. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

16. Safety Check

Upon completion of any service or repairs to this equipment, ask the service technician to perform safety checks to determine that the equipment is in proper operating condition.

17. Field Installation

This installation should be made by a qualified service person and should conform to all local codes.

18. Correct Batteries

Warning: Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

19. Tmra

A manufacturer’s maximum recommended ambient temperature

(Tmra) for the equipment must be specified so that the customer and installer may determine a suitable maximum operating environment for the equipment.

20. Elevated Operating Ambient Temperature

If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).

21. Reduced Air Flow

Installation of the equipment in the rack should be such that the amount of airflow required for safe operation of the equipment is not compromised.

22. Mechanical Loading

Mounting of the equipment in the rack should be such that a hazardous condition is not caused by uneven mechanical loading.

23. Circuit Overloading

Consideration should be given to connection of the equipment to supply circuit and the effect that overloading of circuits might have on over current protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

24. Reliable Earthing (Grounding)

Reliable grounding of rack mounted equipment should be maintained.

Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).

eSATA External Storage

Table of Contents

Chapter 1 — Introduction .......................................................................................... 1

Features ................................................................................................................ 1

Package Contents ................................................................................................. 1

Specifications ........................................................................................................ 1

Rear Panel ............................................................................................................ 2

Front Panel ............................................................................................................ 2

Chapter 2 — Installation ............................................................................................ 3

HDD Models .......................................................................................................... 3

Installation ............................................................................................................. 3

DVR Connection.................................................................................................... 5 iii

Operating Instructions iv

eSATA External Storage

Chapter 1 — Introduction

FEATURES

Your eSATA external storage device has a Serial ATA (SATA) interface. It is easy to install in a cabinet along with a Digital Video Recorder (DVR) and its maximum of four SATA hard disk drives offers excellent space savings. It has the following features:

 19-inch rack mount type

 SATA-to-SATA port multiplier solution

 Maximum of 3.0Gbps transfer rate (SATA II)

 Maximum of four hard disk drives

 Maximized space saving and capacity relative to cost

 Easy expandability creating a very large storage pool

PACKAGE CONTENTS

The package contains the following:

 eSATA External Storage

 AC Power Cord

 eSATA Cable

 Operating Instructions (This document)

 SATA HDD Carrier and Screws

NOTE: The SATA HDD carrier and screws are not provided separately if hard disk drives are already installed in the unit.

WARNING: ROUTE POWER CORDS SO THAT THEY ARE NOT A TRIPPING HAZARD.

MAKE CERTAIN THE POWER CORD WILL NOT BE PINCHED OR ABRADED BY FURNITURE.

DO NOT INSTALL POWER CORDS UNDER RUGS OR CARPET. THE POWER CORD HAS

A GROUNDING PIN. IF YOUR POWER OUTLET DOES NOT HAVE A GROUNDING PIN

RECEPTACLE, DO NOT MODIFY THE PLUG. DO NOT OVERLOAD THE CIRCUIT BY

PLUGGING TOO MANY DEVICES IN TO ONE CIRCUIT.

SPECIFICATIONS

Host Connectivity

External eSATA port (DVR connection)

Max. Transfer Speed (SATA II): 3.0Gbps, Cable Length: Max. 2.0m

Disk Connectivity SATA Hard Disk Drive (Max. 4), 1.5Gbps or 3.0Gbps (Auto detection)

Dimensions (W x H x D) 19.06 x 1.73 x 17.72 (484mm x 44mm x 450mm)

Unit Weight

Shipping Weight

11.9 lbs. (5.4kg) (HDD not installed)

18.3 lbs. (8.3kg) (HDD not installed)

Operating Temperature

Operating Humidity

Power

41°F to 113°F (5°C to 45°C)

20% to 70% (Non-condensing)

115V ~ 230VAC, Max. 2A, 50/60Hz

NOTE: Specifications are subject to change without notice.

1

Operating Instructions

REAR PANEL

① Power Fan : Keeps the SMPS inside the unit at an optimal temperature.

② Cooling Fan : Keeps the unit at an optimal temperature.

③ Connection LED : Lights when data is being transferred to or from the unit.

④ eSATA Port : Connect to a DVR to transfer data.

⑤ Operation LED : Lights when the unit is connected to a DVR.

⑥ Power Switch : Turns the unit on or off.

⑦ Power Connector : Connect to a power outlet using the power cord.

FRONT PANEL

① Power LED : The LED is lit when the system is operating.

② HDD LED (1 to 4) : A green LED is lit when a SATA hard disk drive is installed. A red LED is lit when data is transferring to or from the unit. Green and red LEDs flicker when any error occurs in the installed SATA hard disk drives.

③ Ventilation Holes : Allows air to pass through the unit for cooling.

2

eSATA External Storage

Chapter 2 — Installation

HDD MODELS

Some models of hard disk drives might not work properly, and it is recommended that you use the following hard disk drives models:

Capacity Manufacturer Model Name Remark

250GB

500GB

750GB

Seagate ST3250820SCE

Western Digital WD2500AVJS

Seagate ST3500830SCE

Western Digital WD5000AVJS

Hitachi HDS721050CLA362

Seagate ST3750840SCE

Western Digital WD7500AVCS

1TB

Seagate ST31000340SV

Western Digital WD10EVCS

2TB Hitachi HDS722020ALA330

NOTE: The list is subject to change without notice. Ask your dealer or distributor for the latest list.

INSTALLATION

Install the SATA hard disk drives (maximum of 4) following these instructions.

1.

Remove screws from the top cover and slide the top cover toward the back.

2.

Prepare the SATA HDD carrier.

3

Operating Instructions

3.

Place the hard disk drive on the SATA HDD carrier and attach it firmly with the screws.

NOTES:

 There is no need to change the master/slave jumper settings.

 The front and rear of the carrier are not the same. Center the hard disk drive on the carrier.

4.

Attach the SATA HDD carrier assembly to the unit base and screw it down with the pan head screw.

5.

Connect a power cable and SATA cable to each hard disk drive. The SATA cables should be connected in the order shown.

NOTES:

 Connect the cables tightly paying attention to the cable orientation.

 If the SATA cables are not connected in order, the HDD indicator LEDs will not match the HDD operation.

4

eSATA External Storage

6.

Close the top cover and screw it down.

DVR CONNECTION

The eSATA external storage is connected to the DVR using the closed eSATA cable.

CAUTIONS:

 Shut down the DVR system and remove the power cable from the DVR before connecting the unit.

 You must connect and disconnect the power cables in the following order:

– Connecting: Unit → DVR

– Removing: DVR → Unit

1.

Connect one end of the eSATA cable to the eSATA port on the rear panel of the storage unit and the other end to the eSATA port on the rear panel of the DVR.

2.

Connect the power cord to the storage unit and to the power outlet and turn on the power switch on the rear panel of the storage unit.

3.

Connect the DVR power cord and turn on the DVR system.

CAUTION: Make certain that storage unit’s power switch is turned on before turning on the DVR system.

4.

LEDs on the front and rear panels of the storage unit are lit.

CAUTION: Do NOT remove the eSATA cable while the unit or DVR is operating, otherwise, the unit or DVR may not operate correctly.

V1.0 5

eneo ® is a registered trademark of Videor E. Hartig GmbH

Exclusive distribution through specialised trade channels only.

Videor E. Hartig GmbH

Carl-Zeiss-Straße 8 · 63322 Rödermark, Germany

Tel. +49 (0) 60 74 / 888-0 · Fax +49 (0) 60 74 / 888-100 Technical changes reserved. www.videor.com © C opyright by Videor E. Hartig GmbH 06/2011

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement