Raymarine Maxiview ST80 Operation & Setup
Raymarine Maxiview ST80 is a multifunctional display that provides a wide range of sailing and navigation data. It is designed to be easy to use, with a simple and intuitive interface. The display is large and clear, and can be customized to show the information that is most important to you. Maxiview ST80 is also waterproof and can be used in all weather conditions.
Advertisement
Advertisement
Distributed by
Any reference to Raytheon or
RTN in this manual should be interpreted as Raymarine.
The names Raytheon and RTN are owned by the
Raytheon Company.
ST80
Maxiview
Operation & Setup
Maxiview
ST80 Maxiview Operation and Setup
Package Contents
1. Maxiview display head
2. Thumb nuts (2)
3. Threaded fixing studs (2)
4. White sun cover
5. SeaTalk cable
6. Installation template
7. Operation manual
8. Warranty card
9. Operation cue card
10. Display head installation guide
1
2
Contents
ST80 Maxiview Operation and Setup
Chapter 1: Introduction ............................................................. 7
Quick Reference Guide ............................................... 7
Chapter 2: Operation ............................................................... 10
2.1 General ...................................................................... 10
Operating the Maxiview using the Remote Keypad .... 10
Keypad Beeps ........................................................... 10
Gaining Control of the Maxiview ........................ 10
2.2 Speed Chapter ............................................................ 11
Boat Speed Page ........................................................ 11
Speed Over Ground (SOG) Page ................................ 12
Velocity Made Good (VMG) to Wind Page ................ 12
Log/Trip Page ........................................................... 13
Average Speed .......................................................... 14
Maximum Speed Page ............................................... 14
2.3 Depth Chapter ............................................................ 15
Depth Page ................................................................ 15
Minimum Depth Page ............................................... 16
Depth Offset Page ..................................................... 16
2.4 Wind Chapter ............................................................. 17
Apparent Wind Speed page ....................................... 17
Apparent Wind Angle Page ....................................... 17
True Wind Speed Page (Relative to the Vessel) .......... 18
True Wind Angle (Relative to the Vessel) .................. 18
True Wind Angle (Referenced to the Compass) .......... 19
2.5 Heading Chapter ......................................................... 19
Heading Page ............................................................ 19
Steering Page ............................................................ 20
Course Over Ground (COG) Page .............................. 20
Bearing to Waypoint (BTW) Page ............................. 21
Tack Course Page ...................................................... 21
ST80 Maxiview Operation and Setup 3
2.6 Navigate Chapter ........................................................ 22
Position Page ............................................................. 22
Course Over Ground (COG) & Bearing to Waypoint
(BTW) ...................................................................... 22
Cross Track Error ...................................................... 23
Velocity Made Good (VMG) to Waypoint Page ......... 23
Waypoint Data Page .................................................. 24
Date/Time/Tide Page ................................................ 25
2.7 Race Timer Chapter .................................................... 26
Race Start Page ......................................................... 26
2.8 Multi-Line .................................................................. 27
Help/Setup Page ........................................................ 27
Multi-line Setup ........................................................ 28
List of Multi-line Selections ................................ 29
Multi-line Factory Defaults ................................. 30
2.9 Illumination ............................................................... 31
Resetting the Contrast ................................................ 32
2.10 Data Lost .................................................................. 32
2.11 Man Overboard and Alarms ...................................... 32
Man Overboard ......................................................... 32
Dead Reckoned MOB ......................................... 32
Lat/Lon MOB ........................................................... 33
Incomplete MOB Data .............................................. 33
MOB Audible Alarm .......................................... 34
Alarms ...................................................................... 34
Audible Alarms ......................................................... 35
4 ST80 Maxiview Operation and Setup
Chapter 3: Setup ...................................................................... 36
3.1 Entering Setup ............................................................ 36
Speed Chapter ........................................................... 37
Response Pages .................................................. 37
Trend Indicator Thresholds ................................. 38
Display Format ................................................... 40
Depth Chapter ........................................................... 40
Depth Response .................................................. 41
Trend Indicator Thresholds ................................. 41
Depth Display Format ......................................... 42
Wind Chapter ............................................................ 42
Wind Speed Response ........................................ 43
Wind Angle Response ........................................ 43
Display Format ................................................... 44
Multiline Chapter ...................................................... 44
Editing Rights .................................................... 45
3.2 Instrument Setup ........................................................ 46
Transducers Page ...................................................... 46
Sail/Power/Custom Selection .................................... 47
Custom .............................................................. 48
Contents Setup ................................................... 49
Title Control ....................................................... 50
Variation ............................................................ 51
True/Magnetic Heading ...................................... 52
Lamp Offset Adjustment .................................... 53
Contrast Adjustment ........................................... 54
LCD Inversion ................................................... 55
Alarm Control .................................................... 56
3.3 Quitting User Setup .................................................... 57
ST80 Maxiview Operation and Setup 5
Chapter 4: CodeLock Security ................................................. 58
4.1 What is CodeLock? .................................................... 58
Master’s .................................................................... 58
Slave’s ...................................................................... 58
4.2 Analogue Display Heads ............................................. 59
Automatic CodeLock Systems ................................... 59
Manual CodeLock System ......................................... 59
4.3 Enabling CodeLock .................................................... 59
Chapter 5: Problem Solving ..................................................... 60
Chapter 6: EMC and Servicing Guidelines .............................. 61
6.1 Important information................................................. 61
6.2 Installation ................................................................. 61
6.3 Check Before Going to Sea ......................................... 62
6.4 Servicing and Safety ................................................... 62
Chapter 7: Specification ......................................................... 63
6 ST80 Maxiview Operation and Setup
ST80 Maxiview Operation and Setup
Chapter 1: Introduction
SPEED
maxiview
KNOTS
7
D1580-1
The Maxiview is a large-screen LCD repeater capable of displaying single or multiple lines of alphanumeric SeaTalk data.
With a display area measuring 126 x 70mm (5 x 2.7in), the
Maxiview provides a clear and unambiguous display wherever you are on your boat.
Unlike the other ST80 display heads, the Maxiview has a key-less facia. All user functions are controlled from the ST80 Remote
Keypad or, alternatively, a Masterview with the “Maxiview remote control mode” chapter enabled.
Quick Reference Guide
The illustration on the following two pages provides a quick reference guide to the complete range (Sail configuration) of the
Maxiview chapters and pages.
The Maxiview can be set to ignore the sail/power chapter and page selections and display user-defined custom selections. For further information on making custom selections, please refer to the Sail and Power Selection Page.
8 ST80 Maxiview Operation and Setup
Quick Reference Guide
maxiview remote
Press this key momentarily to cycle the available chapters.
Press and hold for 1 second to select illumination adjustment. Additional key presses change the illumination setting.
maxiview
12.5 FT
120oM remote
Press this key momentarily to cycle pages within the currently selected chapter.
Press and hold for 1 second to return to the previous page.
maxiview
Use the arrow keys to select another
Maxiview display.
Note:
The selected Maxiview display head changes to reverse video.
masterview
MAXIVIEW
REMOTE masterview
MAXIVIEW
REMOTE
The Maxiview can also be operated from a Masterview display.
Use the middle two keys to cycle chapters and pages and select another
Maxiview. The key changes the key functions from chapter/page to select.
ST80 Maxiview Operation and Setup
CHAPTERS PAGES
SPEED
CHAPTER
DEPTH
CHAPTER
WIND
CHAPTER
HEADING
CHAPTER
NAVIGATE
CHAPTER
SPEED
DEPTH
SPEED
OVER
GROUND
MINIMUM
DEPTH
VMG
TO
WIND
NP
LOG &
TRIP
DEPTH
OFFSET
NP
AVERAGE
SPEED
MAXIMUM
SPEED
APPARENT
WIND
SPEED
APPARENT
WIND
ANGLE
SAILING
TRUE WIND
SPEED
NP
SAILING
TRUE WIND
ANGLE
NP
MAGNETIC
TRUE WIND
ANGLE
NP
HEADING
POSITION
STEER
NP
COURSE
OVER
GROUND
COG
BTW
CROSS
TRACK
ERROR
BEARING
TO
WAYPOINT
VMG
TO
WAYPOINT
TACK
COURSE
WAYPOINT
DATA
NP
DATE
TIME
TIDE
TIMERS
CHAPTER
NP
MULTILINE
CHAPTER
RACE
TIMER
NP
UP TO 8
USER DEFINED
PAGES
NP: Page not available if the power option has been selected
Maximum Speed & Minimum Depth
The maximum speed and minimum depth displays can be reset by pressing and holding the & keys together for 4 seconds - the display flashes during this period.
9
10 ST80 Maxiview Operation and Setup
Chapter 2: Operation
2.1 General
The Maxiview operates around a chapter and page principle – chapters are independent sections: speed, depth, wind, etc., and pages data related to that chapter.
When the Maxiview is powered up for the first time, the unit defaults to the SAIL configuration, unless a POWER configuration is received via SeaTalk (refer to the Masterview setup chapter).
Operating the Maxiview using the Remote Keypad
To operate the Maxiview using the Remote Keypad, you must first carry out the setup procedures covered in the ST80 Remote Keypad setup chapter.
Note: SeaTalk data must be available for a chapter to function. For example, if speed data is lost for 8 seconds, the speed chapter is replaced by a warning screen.
Keypad Beeps
• The keypad beeps once every time a key is pressed.
• An incorrect key sequence causes the Maxiview to beep a further 2 times.
Gaining Control of the Maxiview
• In order to make changes to the Maxiview displays, you must gain control of the required Maxiview.
• Control is confirmed by the display changing to reverse video.
ST80 Maxiview Operation and Setup
2.2 Speed Chapter
Boat Speed Page
This page displays your actual boat speed.
SPEED KNOTS
10.5
maxiview remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2469-1
• The speed units are the units currently on SeaTalk: KNOTS, MPH or KM/H.
• Trend indicators ▲ or ▼ are displayed if the boat speed is generally decreasing or increasing at a rate greater than the value set in setup.
• The indicators are, by default, turned off.
11
12 ST80 Maxiview Operation and Setup
Speed Over Ground (SOG) Page
This page displays your current speed over the ground from GPS.
maxiview
KNOTS SOG
6.5
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
• The speed units can be: KNOTS, MPH or KM/H.
Press for 1 second to return to the previous page.
D2470-1
Velocity Made Good (VMG) to Wind Page
VMG to wind displays your boat speed through the water in the direction of true wind.
maxiview
KNOTS VMG WIND
6.3
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2471-1
• The units are those currently on SeaTalk: KNOTS, MPH or KM/H.
• Trend indicators ▲ or ▼ are displayed if the VMG is generally decreasing or increasing at a rate greater than the value set during calibration. The indicators are, by default, turned off.
• This page is not available if the unit is operating in POWER mode.
ST80 Maxiview Operation and Setup 13
Log/Trip Page
The Log/Trip page displays the total distance logged and a list of trips and their current status.
LOG/ TRIP
LOG
TRIP 1 OFF
TRIP 2 OFF
TRIP 3 ON
TRIP 4 OFF
TRIP 5 ON maxiview
NM
10000.5
1000.5
1102.5
20.20
0.00
50.85
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2472-1
• The units are those currently on SeaTalk: NM, SM or KM.
• The trip list and the log cannot be controlled from the Maxiview.
Please refer to the Masterview handbook for trip control information.
14 ST80 Maxiview Operation and Setup
Average Speed
This page displays the average boat speed for your current journey.
maxiview
KNOTS SPEED
AVG
8.0
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2473-1
• The units are those currently on SeaTalk: KNOTS, MPH or KM/H.
• The word STOPPED is displayed if this feature is not running.
• The maximum averaging period is 24 hours.
Maximum Speed Page
This displays the maximum speed achieved during the current voyage.
maxiview
KNOTS SPEED
MAX
8.5
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
Press and hold these keys for 4 seconds to reset the maximum speed.
D2474-1
• The units are those currently on SeaTalk: KNOTS, MPH or KM/H.
• The display flashes for 4 seconds when the maximum speed is reset.
ST80 Maxiview Operation and Setup
2.3 Depth Chapter
Depth Page
The depth page displays the current depth available on SeaTalk.
maxiview
DEPTH FEET
32.5
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2475-1
• The displayed units are those currently on SeaTalk: FEET,
FATHOMS or METRES.
• Trend indicators ▲ or ▼ are displayed if the trend is generally towards decreasing or increasing depth at a rate greater than that set during calibration.
• The indicators are, by default, turned off.
• If the depth echo is lost the last valid echo is displayed together with the caption “LAST ECHO”. Also, the current units are abbreviated to FT, FA or M.
15
16 ST80 Maxiview Operation and Setup
Minimum Depth Page
maxiview
DEPTH MIN 9.2
FT remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
Press and hold these keys for 4 seconds to reset the minimum depth.
D2476-1
• The units are: FEET, FATHOMS or METRES.
• The time of the last echo is displayed in the 12 or 24 hour clock. This field is deactivated if time is not available.
• The display flashes for 4 seconds when the minimum depth is reset.
Depth Offset Page
This page displays the depth transducer offset.
maxiview
DEPTH OFFSET -2.0
KEEL
FT remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2477-1
• The units are FEET (FT), FATHOMS (FA) or METRES (M).
• The offset can be keel, transducer or waterline – no adjustment is possible from the Maxiview.
ST80 Maxiview Operation and Setup
2.4 Wind Chapter
Apparent Wind Speed page
maxiview
WIND APP
KNOTS
20.0
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
remote
Press for 1 second to return to the previous page.
D2478-1
• The units can be : KNOTS or M/SEC.
Apparent Wind Angle Page
s STBD WIND APP
090 maxiview remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2479-1
• The direction indicator is displayed as PORT or STBD.
17
18 ST80 Maxiview Operation and Setup
True Wind Speed Page (Relative to the Vessel)
maxiview
KNOTS
8.5
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
• The true wind units can be either: KNOTS or M/S.
• This page is not available in POWER mode.
Press for 1 second to return to the previous page.
D2480-1
True Wind Angle (Relative to the Vessel)
maxiview
PORT
096 remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2481-1
• The direction indicator is displayed as PORT or STBD.
• This page is not available in POWER mode.
ST80 Maxiview Operation and Setup
True Wind Angle (Referenced to the Compass)
maxiview
296
WNW
M
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2482-1
• This page is not available in POWER mode.
• The angle can be either true (T) or magnetic (M).
• An inter-cardinal/cardinal representation is also shown at the top right of the screen (e.g., WNW).
2.5 Heading Chapter
Heading Page
maxiview
HEADING
126
TRUE
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
remote
Press for 1 second to return to the previous page.
D2483-1
• The heading can be true or magnetic.
19
20 ST80 Maxiview Operation and Setup
Steering Page
The steering page displays the current compass heading (unlocked mode) or the locked compass heading (locked mode).
Note: For a detailed description of locked mode, please refer to a
Masterview handbook.
maxiview
UNLOCKED STEER
136
T
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2484-1
• The displayed value can be true (T) or magnetic (M).
Course Over Ground (COG) Page
This page displays your true or magnetic course over the ground.
maxiview
COG
236
TRUE remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2485-1
• Whether the course is true or magnetic is dependant on the units currently on SeaTalk.
ST80 Maxiview Operation and Setup
Bearing to Waypoint (BTW) Page
This page shows the magnetic or true bearing to a target waypoint.
maxiview
BTW
276
TRUE remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2486-1
Tack Course Page
This page displays the course for the next (opposite) tack in degrees true or magnetic.
maxiview
326
TRUE
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
remote
Press for 1 second to return to the previous page.
D2487-1
• This page is not available in POWER mode.
• The tack course is based on sailing true wind.
21
22 ST80 Maxiview Operation and Setup
2.6 Navigate Chapter
Position Page
POSITION maxiview
N-E
050 49.10
002 49.10
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2488-1
• If position data is not available the fields are filled with dashes.
Course Over Ground (COG) & Bearing to
Waypoint (BTW)
This page displays both your course over ground and the bearing to a target waypoint in degrees true or magnetic.
COG
TRUE
BTW
TRUE maxiview
240
272
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
remote
Press for 1 second to return to the previous page.
D2489-1
ST80 Maxiview Operation and Setup
Cross Track Error
The cross track error (XTE) page shows how far, in nautical miles
(NM), statute miles (SM) or kilometres (KM), your vessel is from a planned route.
maxiview
XTE
0.34
NM remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2490-1
• The arrows indicate the direction to steer to correct any error.
Velocity Made Good (VMG) to Waypoint Page
This page displays your boat speed over the ground in the direction of a target waypoint.
maxiview
KNOTS
13.5
remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2491-1
• Trend indicators ▲ or ▼ are displayed if the trend is generally towards decreasing or increasing VMG. The indicators are, by default, turned off.
23
24 ST80 Maxiview Operation and Setup
Waypoint Data Page
This page displays any cross track error, the distance to a target waypoint (DTW), estimated time to arrival (ETA) and waypoint number.
010
DTW
ETA
1.2
maxiview
25.5 NM
01: 30: 15 remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2492-1
• The arrows to the right or left of the XTE value indicate the direction to steer.
• The distance to waypoint can be nautical miles (NM), statute miles
(SM) or kilometres (KM).
• The ETA value is the time to go in hours, minutes and seconds.
ST80 Maxiview Operation and Setup 25
Date/Time/Tide Page
This page displays the speed and direction of the tide and the local time.
12 JUNE 95 maxiview
TIDE 6.5 KNOTS
130 TRUE remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
D2493-1
• Local time is a calculation based on a global offset . Please refer to the Masterview handbook for details.
• The time and date format is taken from data on SeaTalk.
• Tide and speed units can be KNOTS, MPH or KM/H.
• The tide can be magnetic or true.
26 ST80 Maxiview Operation and Setup
2.7 Race Timer Chapter
Race Start Page
This page duplicates race timer data from a Masterview instrument.
There are just two operating modes: STOPPED and COUNTING
DOWN/UP.
maxiview
RACE START
10:00 remote
Press momentarily to advance to the next chapter.
• The display shows minutes and seconds only.
• When the timer reaches 00:00 the timer enters race mode (see below).
D2494-1 maxiview
RACE TIME
01:30 remote
Press momentarily to advance to the next chapter.
D2495-1
• In race mode the timer shows the elapsed time in minutes and seconds up to 1 hour, and hours and minutes thereafter (seconds are displayed in small characters).
ST80 Maxiview Operation and Setup
2.8 Multi-Line
Multi-line chapters consist of up to 8 pages of user-defined pages.
DEPTH
7.2
SPEED maxiview
2
FEET
6.7 KTS
HEADING 120 M remote
Press momentarily to advance to the next chapter.
Press momentarily to advance to the next page.
Press for 1 second to return to the previous page.
Press these keys together momentarily to enter help/edit mode.
D2496-1
• The multi-line page number is shown at the top-right of the screen.
Help/Setup Page
maxiview
HELP: PRESS ANY KEY...
CHAP +
CHAP
+
PAGE
CHAP
PAGE
+
CHAP
+
PAGE
+
INSERT PAGE
DELETE PAGE
NEXT DATA
PREV. DATA
NEXT LINE
1- 2 LINE
EXIT remote
Advance to
Multiline setup page.
Advance to
Multiline setup page.
Press these keys together momentarily to exit multiline setup.
D2497-1
• Multi-line setup/help is only available if “EDIT ALL” or “EDIT
PAGES” has been selected in setup.
• When you exit Multi-line edit, the display returns to the previous
Multi-line page.
• The display returns to the previous Multi-line page after 8 seconds of keypad inactivity.
27
28 ST80 Maxiview Operation and Setup
Multi-line Setup
maxiview
2
DEPTH
25.2
SPEED
FEET
6.5 KTS
HEADING 120 M remote
Press to change the current option to the previous option.
Press to change the current option to next option.
Press these keys together momentarily to switch between
1 and 2 line entries.
Press and hold these keys for 4 seconds to delete the current multiline page.
Press these keys together momentarily to exit setup and return to the current multiline page.
Press and hold these keys for 4 seconds to insert new multiline page before current.
Press these keys together momentarily to select next line.
D2498-1
• The currently selected line appears in reverse video.
• The current page appears in the top right hand corner of the display.
• The display flashes for 4 seconds when a page is deleted. After 4 seconds, “PAGE DELETED” is displayed along with the deleted page number.
• The next page is displayed when a page is deleted.
• The display flashes for 4 seconds when a page is inserted. After 4 seconds, “PAGE INSERTED” is displayed.
• A single line at the bottom of the display cannot be changed for a two-line entry.
• New pages always consist of 4 lines. Each line displays speed data until it is changed.
• Page numbers are automatically renumbered when pages are inserted or deleted.
ST80 Maxiview Operation and Setup 29
List of Multi-line Selections
The lines of data that can be selected are as follows:
5
6
3
4
7
Line Data
1 Speed
2 Speed over ground
Velocity made good to wind
Velocity made good over ground
Log
Trip 1
Average speed
8
9
Depth
Water temperature
10 Apparent wind speed
11 Apparent wind angle
12 True wind speed
13 True wind angle relative
14 True wind angle absolute
15 Beaufort
16 Heading
Line Data
17 Steer
18 Course over ground
19 Tack course
20 Vessel latitude
21 Vessel longitude
22 Cross track error
23 Velocity made good to wayp’t
24 Waypoint number
25 Distance to waypoint
26 Bearing to waypoint
27 Estimated time to arrival
28 Date
29 Time
30 Tide set
31 Tide drift
30 ST80 Maxiview Operation and Setup
Multi-line Factory Defaults
The factory defaults for the Multi-line pages are:
Page Line
1
3
4
1
2
2
3 1
2
3
4
1
2
4
5
6
7
8
3
4
1
2
1
2
3
4
1
2
3
4
1
2
3
4
1
2
Content
Speed
Average speed
Speed over ground
Velocity made good to waypoint
Depth
Water temperature
Heading
Steer
Course over ground
Bearing to waypoint
True wind angle
True wind speed
Tack course
Beaufort
Waypoint number
Cross track error
Distance to waypoint
Estimated time to arrival
Speed
Depth
Speed
Depth
Apparent wind angle
Apparent wind speed
Course over ground
Speed over ground
Tide set
Tide drift
ST80 Maxiview Operation and Setup
2.9 Illumination
There are two modes: local and system. Each of these modes has four possible settings: level 3 (brightest), level 2, level 1 and off.
Local illumination is used to adjust the lighting of individual display heads — adjustments will not affect other display heads.
System illumination controls the lighting of all display heads in system mode.
LOCAL LAMPS maxiview
3 remote
Press this key for 1 second from any page to open the illumination display.
In local illumination, press this key for 5 second to change to system illumination.
Once the local or system illumination display is active, press this key momentarily to adjust the current setting.
Press this key for 1 second to reset the contrast.
In system illumination, press this key for 1 second to return to local illumination.
D2540-1
• Local mode remains active until the power supply is switched off, or the mode is changed to system.
• If the LCD illumination is off when adjustment mode is entered, the unit automatically defaults to level 3.
• If the LCD is already illuminated the current level is displayed upon entry into adjustment mode.
• The display returns to normal operation if there are no further key presses within 8 seconds.
31
32 ST80 Maxiview Operation and Setup
Resetting the Contrast
The display contrast can, during local or system illumination adjustment, be reset to the factory default by pressing the page key for 1 second.
2.10 Data Lost
If a chapter that is dependent on a given quantity, e.g., speed, wind, depth, and this data is lost for more than 8 seconds, a warning screen is displayed until the data is restored.
maxiview
WARNING
SPEED CHAPTER
NOT AVAILABLE
DATA LOST remote
2.11 Man Overboard and Alarms
Man Overboard
Man overboard displays are triggered when a man overboard condition exists on SeaTalk. These displays replace the current display until the condition no longer exists.
Dead Reckoned MOB
D2560-1 maxiview
MOB
DR 08:30
078 TRUE
1.2 NM
remote
Press this key momentarily to display Lat/Lon information if available.
D2542-1
ST80 Maxiview Operation and Setup
• The dead reckoned screen is displayed providing data is available.
• Fields where data is not available appear as dashes.
• The elapsed time is displayed in minutes and seconds.
• The displayed bearing and range is to the man in the water.
Lat/Lon MOB
maxiview
MOB
POS 08:30
078 TRUE
1.2 NM
remote
Press this key momentarily to display dead reckoned information if available.
D2543-1
• This screen is displayed upon entry to MOB if dead reckoned information is not available.
• Time data may not be shown if the man-overboard data is not sourced from ST80.
Incomplete MOB Data
If there is insufficient data to provide range, bearing and elapsed time, the following screen is displayed during an MOB condition.
MAN
OVER
BOARD
maxiview remote
D2544-1
33
34 ST80 Maxiview Operation and Setup
MOB Audible Alarm
During an MOB condition, an audible alarm beeps 3 times every thirty seconds.
Alarms
The Maxiview can be set to respond to all the alarms in the following table or, alternatively, only those identified as specific.
Alarm
Shallow depth
Deep depth
Anchor
True wind high speed
True wind low speed
True wind high angle
True wind low angle
Apparent wind high speed
Apparent wind low speed
Apparent wind high angle
Apparent wind low angle
Manual off-course
ST80 full watch
Pop-Up Displayed
SHALLOW WATER
DEEP WATER
ANCHOR ALARM
TRUE WIND SPEED HIGH
TRUE WIND SPEED LOW
TRUE WIND ANGLE HIGH
TRUE WIND ANGLE LOW
APPARENT WIND SPEED HIGH
APPARENT WIND SPEED LOW
APPARENT WIND ANGLE HIGH
APPARENT WIND LOW ANGLE
OFF COURSE
WATCH PERIOD EXPIRED
The following display is activated when an alarm is received. This display flashes continuously until silenced/turned off or the alarm description page is selected.
Response
All
All
All
All
All
All
All
Specific
All
All
All
All
All maxiview
Press either key momentarily to display the alarm title pop-up or the alarm description page.
remote
When the alarm title pop-up is displayed, press either of these keys to silence or turn off the alarm.
D2541-1
ST80 Maxiview Operation and Setup 35
The following table lists the alarm status once a silence/turn off key- sequence is performed.
Alarm
Shallow depth
Deep depth
Anchor
True wind high speed
True wind low speed
True wind high angle
True wind low angle
Apparent wind high speed
Apparent wind low speed
Apparent wind high angle
Apparent wind low angle
Manual off-course
Full ST80 watch
No
No
No
No
No
Yes
Yes
No
No
No
Silenced
Yes
No
Yes
• If an alarm is currently active and an alarm of greater importance is received, the current alarm is replaced with the new alarm.
• Replaced alarms are not stored by the Maxiview. However, the alarm remains on SeaTalk and, if the condition still exists once the current alarm has cleared, will be reinstated.
• Silenced alarms will repeat after 30 seconds if the condition persists.
Turned Off
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Audible Alarms
There are basically two types of audible alarm: high priority and low priority.
High priority alarms beep continuously while low priority alarms consist of three beeps followed by a 5 second break.
• High priority alarms will always override low priority alarms.
• Once a high priority alarm has cleared, the previous alarm, if it is still current, will be reactivated.
36 ST80 Maxiview Operation & Setup
Chapter 3: Setup
This chapter describes how to set and adjust features in the setup menu. These include display formats, response levels for controlling the frequency of screen updates and the thresholds for trend indicators.
3.1 Entering Setup
DEPTH f FEET
36.5
maxiview remote
Press and hold these keys together for 2 seconds to display the user set-up screen.
maxiview
SET- UP
PRESS " PAGE" TO
CONTINUE...
remote
Press this key momentarily to advance to user setup.
D2499-1
• The Maxiview returns to normal operation after 4 seconds of keypad inactivity.
• “SET-UP OFF” replaces the above screen if user setup has been turned off in dealer setup.
• Setup can be entered from any normal operating display.
ST80 Maxiview Operation & Setup
Speed Chapter
The following screen is displayed for 2 seconds when entering speed setup. The key sequences shown are only available during this period.
maxiview
SPEED
SET-UP
CHAP 1S FOR
INSTRUMENT CHAPTER remote
Press this key to advance to the next chapter.
Press this key for 1 second to return to the instrument chapter.
D2500-1
Response Pages
Response is used to control the speed at which screens are updated.
The response range is from 0 to 15. A high number results in rapid changes of the displayed data while a low number gives a slow but smooth update.
37
38 ST80 Maxiview Operation & Setup
There are two response pages: speed and VMG to wind. Speed response covers boat speed, speed over ground, velocity made good to waypoint and velocity made good over ground to waypoint.
S maxiview
SET-UP
SPEED
16.5
KNOTS
RESPONSE
07 F remote
S maxiview
SET-UP
VMG
WIND
5.0
RESPONSE
KNOTS
10 F
Press this key momentarily to advance to the next chapter.
Press this key momentarily to advance to the next page.
Press this key for 1 second to return to the previous page.
Press these keys together momentarily to decrease value by 1.
Press these keys together momentarily to increase value by 1.
D2501-1
• The current boat speed/VMG to wind is always displayed.
• The current response level is shown below the adjustment bar.
• Response applies only to the unit on which it is adjusted – it is not a global change.
Trend Indicator Thresholds
The trend arrows ( ▲ or ▼ ) indicate the whether the general trend is towards a higher or lower boat speed, SOG or VMG to wind. The trend, whether its higher or lower, is determined by the threshold setting.
ST80 Maxiview Operation & Setup maxiview
SET-UP
BOAT SPEED TREND
THRESHOLD
0.80
KNOTS/ SEC
SET-UP
SOG TREND
THRESHOLD
2.50
KNOTS/ SEC maxiview remote maxiview
SET-UP
VMG WIND TREND
THRESHOLD
0.80
KNOTS/ SEC
Press this key momentarily to advance to the next chapter.
Press this key momentarily to advance to the next page.
Press this key for 1 second to return to the previous page.
Press these keys together momentarily to decrease value by 0.01.
Press these keys together momentarily to increase value by 0.01.
Press these keys together momentarily to switch the trend arrows ON/OFF.
D2502-1
• The threshold is displayed in units (e.g., knots) per second.
• The threshold setting applies to the unit on which it is adjusted only.
39
40 ST80 Maxiview Operation & Setup
Display Format
The display format can be set to either 1 or 2 decimal places.
maxiview
SET-UP
BOAT SPEED
DISPLAY FORMAT
X.X
X.XX
✓
✗ remote
Press this key momentarily to advance to the next chapter.
Press this key momentarily to advance to the next page.
Press this key for 1 second to return to the previous page.
Press these keys together momentarily to highlight X.X format.
Press these keys together momentarily to highlight X.XX format.
Press these keys together momentarily to select format.
• Values are limited to 3 significant figures. Values over 9.99 with
X.XX selected will be rounded up and truncated, e.g., 10.0.
D2503-1
Depth Chapter
The following screen is displayed for 2 seconds when entering depth setup. The key sequences shown are only available during this period.
maxiview
DEPTH
SET-UP
CHAP 1S FOR
SPEED CHAPTER
Press this key to advance to the next chapter.
remote
Press this key for 1 second to return to the main speed chapter.
D2504-1
ST80 Maxiview Operation & Setup
Depth Response
S maxiview
SET-UP
DEPTH
20.5
RESPONSE
FEET
07 F
Press this key momentarily to advance to the next chapter.
Press these keys together momentarily to decrease value by 1.
Press this key momentarily to advance to the next page.
Press these keys together momentarily to increase value by 1.
Trend Indicator Thresholds
SET-UP
DEPTH TREND
THRESHOLD
2.0
FEET/ SEC maxiview remote
Press this key for 1 second to return to the previous page.
Press this key momentarily to advance to the next chapter.
Press these keys together momentarily to decrease value by 0.1.
Press this key momentarily to advance to the next page.
Press these keys together momentarily to increase value by 0.1.
remote
Press this key for 1 second to return to the previous page.
D2505-1
D2506-1
41
42 ST80 Maxiview Operation & Setup
Depth Display Format
maxiview
SET-UP
DEPTH SPEED
DISPLAY FORMAT
X
X.X
✓
✗ remote
Press this key momentarily to advance to the next chapter.
Press this key momentarily to advance to the next page.
Press this key for 1 second to return to the previous page.
Press these keys together momentarily to highlight X format.
Press these keys together momentarily to highlight X.X format.
Press these keys together momentarily to select format.
D2507-1
Wind Chapter
The following screen is displayed for 2 seconds when entering wind setup. The key sequences shown are only available during this period.
maxiview
WIND
SET-UP
CHAP 1S FOR
DEPTH CHAPTER
Press this key to advance to the next chapter.
remote
Press this key for 1 second to return to the depth chapter.
D2508-1
ST80 Maxiview Operation & Setup
Wind Speed Response
S maxiview
SET-UP
WIND SPEED KNOTS
5.0
RESPONSE
07 F
Press this key momentarily to advance to the next chapter.
Press these keys together momentarily to decrease value by 1.
Wind Angle Response
Press this key momentarily to advance to the next page.
Press these keys together momentarily to increase value by 1.
S
SET-UP
WIND ANGLE
100
P
RESPONSE maxiview
07 F remote
Press this key for 1 second to return to the previous page.
Press this key momentarily to advance to the next chapter.
Press these keys together momentarily to decrease value by 1.
Press this key momentarily to advance to the next page.
Press these keys together momentarily to increase value by 1.
remote
Press this key for 1 second to return to the previous page.
D2509-1
D2510-1
43
44 ST80 Maxiview Operation & Setup
Display Format
maxiview
SET-UP
WIND SPEED
DISPLAY FORMAT
X
X.X
✓
✗ remote
Press this key momentarily to advance to the next chapter.
Press this key momentarily to advance to the next page.
Press this key for 1 second to return to the previous page.
Press these keys together momentarily to highlight X format.
Press these keys together momentarily to highlight X.X format.
Press these keys together momentarily to select format.
D2507-1
Multiline Chapter
The following screen is displayed for 2 seconds when entering multiline setup. The key sequences shown are only available during this period.
maxiview
MULTILINE
SET-UP
CHAP 1S FOR
WIND CHAPTER
Press this key to advance to the next chapter.
remote
Press this key for 1 second to return to the wind chapter.
D2512-1
ST80 Maxiview Operation & Setup 45
Editing Rights
The editing rights chapter allows you to control the level of multiline page editing. The options are: edit all, edit pages and no editing.
SET-UP
MULTILINE
EDIT ALL
EDIT PAGES
NO EDITING maxiview
✓
✗
✗ remote
Press this key momentarily to advance to the next chapter.
Press this key momentarily to advance to the next page.
Press these keys together momentarily to select option.
Press these keys together momentarily to highlight next option.
Press these keys together momentarily to highlight previous option.
• Edit all allows you to edit chapters and pages. Edit pages allows editing of the page contents only .
D2513-1
46 ST80 Maxiview Operation & Setup
3.2 Instrument Setup
maxiview
INSTRUMENT
SET-UP
CHAP 1S FOR
MULTILINE CHAPTER
Press this key to advance to the next chapter.
remote
Press this key for 1 second to return to the multiline chapter.
D2514-1
Transducers Page
This page lists all the transducers connected to SeaTalk.
SET-UP
TRANSDUCERS maxiview
SPEED
DEPTH
WIND
✓
✓
✓ remote
Press this key momentarily to advance to the next chapter.
Press this key momentarily to advance to the next page.
Press this key for 1 second to return to the previous page.
Press these keys together momentarily to scroll down list.
Press these keys together momentarily to scroll up list.
D2515-1
• The complete transducer list is: speed, depth, wind, compass, pilot and GPS.
• Detected transducers are identified by a ✓ . Transducers not detected appear in name only.
ST80 Maxiview Operation & Setup 47
Sail/Power/Custom Selection
This page allows you to select whether chapters are custom selections or, alternatively, dictated by the sail or power boat settings.
SET-UP
SELECT TYPE maxiview
SYSTEM
CUSTOM
✓
✗ remote
Press this key momentarily to advance to the next chapter.
Press these keys together momentarily to highlight custom.
Press this key for 1 second to return to the previous page.
Press these keys together momentarily to highlight system.
Press this key momentarily to: go to the custom setup page if CUSTOM is selected or the chapter title control page if
SYSTEM is selected.
Press these keys together to select (tick) the highlighted option.
D2516-1
• If a selection has not been previously made, the SYSTEM option is automatically tagged and SAIL mode is selected as the default chapter and page mode.
• CUSTOM mode does not affect and is not affected by system settings.
48 ST80 Maxiview Operation & Setup
Custom
This mode allows you to select any of the chapters from the following list:
2
3
No.
Chapter
1 Speed
4
Depth
Wind
Heading
6
7
No.
5
Chapter
Navigate
Timers
Multiline
SPEED
DEPTH
WIND
SET-UP
CHAPTERS maxiview
✓
✗
✓ remote
Press this key momentarily to return to speed calibration chapter.
Press these keys together momentarily to highlight the next listed chapter.
Press this key for 1 second to return to the selection page.
Press these keys together momentarily to highlight the previous chapter.
Press this key momentarily to advance to the
Title Page control.
Press and hold these keys together momentarily to enter control setup.
D2517-1
• Enabled chapters are identified by a ✓ . A ✗ indicates that a chapter is switched OFF or does not have any pages enabled.
• This chapter appears in name only if a chapter is active but fundamental information is missing.
ST80 Maxiview Operation & Setup
Contents Setup
In custom setup, contents setup is used to select or de-select pages within the highlighted chapter.
49 maxiview
SET-UP
NAVIGATE CHAPTER
OFF
POSITION
COG/ SOG
✗
✓
✓ remote
Press these keys together momentarily to highlight the next page.
Press these keys together momentarily to highlight the previous page.
Press this key momentarily to return to the chapter setup page.
Press these keys together momentarily to turn the highlighted page
ON/OFF.
D2518-1
• At least one page must be selected. The last page in a chapter cannot be deleted.
• All pages are de-selected if OFF ( ✓ ) is chosen.
• De-selecting OFF automatically reselects the previously active pages.
50 ST80 Maxiview Operation & Setup
Title Control
This is used to turn the chapter title pages, displayed for 2 seconds upon entry to a chapter, ON or OFF.
SET-UP
CHAPTER TITLE PAGES
ON
OFF maxiview
✓
✗ remote
Press this key momentarily to return to speed calibration chapter.
Press these keys together momentarily to highlight ON.
Press this key momentarily to advance to the variation setup.
Press these keys together momentarily to highlight OFF.
Press this key for
1 second to return to the sail/power/custom selection page.
Press these keys together momentary to select the highlighted option.
D2519-1
ST80 Maxiview Operation & Setup
Variation
This page is used to enter the local variation to the nearest whole degree.
51
SET-UP
VARIATION
003
WEST maxiview remote
Press this key momentarily to return to speed calibration chapter.
Press these keys together momentarily to change value by
1 degree West.
Press this key momentarily to advance to the true/magnetic heading setup.
Press these keys together momentarily to change value by
1 degree East.
Press this key for 1 second to return to the title control page.
D2520-1
• The maximum variation that can be entered is 30°.
• If dashes are currently displayed, the first combination key press will change the display to “000”.
• Variation is transmitted on SeaTalk.
52 ST80 Maxiview Operation & Setup
True/Magnetic Heading
The true/magnetic heading page is used to select one of four options: local true, local magnetic, global true or global magnetic.
maxiview
SET-UP
HEADING DISPLAY
LOCAL TRUE
LOCAL MAGNETIC
GLOBAL TRUE
✗
✓
✗ remote
Press this key momentarily to return to speed calibration chapter.
Press these keys together momentarily to highlight the next option.
Press this key momentarily to advance to lamp adjustment offset.
Press these keys together momentarily to highlight the previous option.
Press this key for 1 second to return to the variation page.
Press these keys together momentary to select the highlighted option.
D2531-1
• Upon exiting setup, the local true and local magnetic settings prevent any response to incoming true or magnetic data.
• If variation is not available, the local and global true options cannot be selected.
ST80 Maxiview Operation & Setup
Lamp Offset Adjustment
This feature allows you to adjust the brightness of individual illumination levels to obtain the best setting for a particular location.
53 maxiview
SET-UP
LAMP ADJSUTMENT
LEVEL
2
MIN 32 MAX remote
Press this key momentarily to advance to contrast adjustment.
Press these keys together momentarily to decrease value by 1.
Press this key for 1 second to return to the previous page.
Press these keys together momentarily to increase value by 1.
Press these keys together momentarily to cycle illumination levels.
• Lamp adjustment is not available if the current setting is OFF.
• The adjustment range is from 1 to 100%.
• If the current mode is “local”, changes will not be transmitted on
SeaTalk. However, changes will occur if the mode is “global”.
D2532-1
54 ST80 Maxiview Operation & Setup
Contrast Adjustment
SET-UP
CONTRAST
ADJUSTMENT maxiview
MIN
Press this key momentarily to return to speed setup.
Press these keys together momentarily to decrease value by 1.
07 MAX remote
Press this key momentarily to advance to LCD inversion control page.
Press these keys together momentarily to increase value by 1.
Press this key for 1 second to return to the previous page.
D2533-1
ST80 Maxiview Operation & Setup
LCD Inversion
LCD inversion allows you to change the display to:
• display black numbers and characters on a light background
• or display light numbers and characters on a black background
55
SET-UP
DISPLAY
NORMAL
REVERSE maxiview
✓
✗ remote
Press this key momentarily to return to speed setup.
Press these keys together momentarily to highlight reverse.
Press this key momentarily to advance to alarm page control.
Press these keys together momentarily to highlight normal.
Press this key for 1 second to return to contrast adjustment.
Press these keys together momentary to select the highlighted option.
D2534-1
56 ST80 Maxiview Operation & Setup
Alarm Control
This page is used to define whether all or just specific alarms will be recognised by the Maxiview.
maxiview
SET-UP
ENABLED ALARMS
ALL
SPECIFIC
✓
✗ remote
Press this key momentarily to return to speed setup.
Press these keys together momentarily to highlight specific.
Press this key momentarily to return to transducers page.
Press these keys together momentarily to highlight all.
Press this key for 1 second to return to LCD inversion.
Press these keys together momentary to select the highlighted option.
D2535-1
ST80 Maxiview Operation & Setup
3.3 Quitting User Setup
To quit setup, simply press the Chapter and Page keys together momentarily to display the following screen.
SET-UP
EXIT
STORE SETTINGS
CANCEL CHANGES maxiview
✗
✓ remote
57
If cancel is selected, press this key momentarily to exit without saving.
If store is selected, press this key momentarily to exit and store new settings.
Press these keys together momentarily to highlight cancel.
Press these keys together momentarily to highlight store.
Press these keys together momentary to select the highlighted option.
D2539-1
58 ST80 Maxiview Operation & Setup
Chapter 4: CodeLock Security
4.1 What is CodeLock?
• CodeLock is a personal four digit security code designed to protect your valuable equipment against theft.
• CodeLock does not have to be switched on, but it’s there if you decide that you need it.
• When CodeLock is switched on, the code number is stored in the memory of all CodeLock compatible equipment on the same bus.
• A CodeLocked piece of equipment, if stolen, cannot be used without the correct code number.
• There are basically two types of CodeLock compatible equipment: masters and slaves.
Master’s
• Are used to create and enter a CodeLock code number.
• The ST80 Masterview is a master display head.
Slave’s
• Cannot be used to create a CodeLock code number.
• Can be used to enter a code number to unlock a system.
• Receive and transmit your chosen code number only.
• ST80 slave’s consist of the: Analogue Wind, Analogue Close Hauled
Wind, Analogue Compass, Maxiview and the Analogue Multitrim.
Code creation is usually a once-off procedure carried out on a master display head, which, ideally, is situated in a secure location below deck. Once entered, the code is automatically sent to all CodeLock compatible SeaTalk equipment without further intervention.
If you require a higher degree of security, perhaps all your instruments are mounted in exposed locations, CodeLock can demand that you enter your personal code every time the system is switched on. In this configuration, the code can be entered into any convenient master display head.
ST80 Maxiview Operation & Setup 59
4.2 Analogue Display Heads
Automatic CodeLock Systems
In an automatically transmitted CodeLock system, the Maxiview reads the code number and starts-up automatically without any user input.
Manual CodeLock System
In a manually transmitted CodeLock system, the code number is entered via the keypad of any master display head. This code is then sent to all compatible equipment on the same SeaTalk bus. Once this code has been received, the equipment operates in the normal way.
4.3 Enabling CodeLock
The CodeLock security feature can only be switched on from a
Masterview display head. Therefore, please refer to the Masterview
Operation & Setup manual for details.
60 ST80 Maxiview Operation & Setup
Chapter 5: Problem Solving
5.1 Problem Solving
Display is blank
• Make sure that the power supply is connected.
• Check the fuse or circuit breaker.
• Make sure that the SeaTalk cables are not damaged.
• Check the contrast and illumination settings
• Faulty LCD module.
No exchange of information between SeaTalk instruments
• Make sure that the cables are attached securely.
• If the problem persists, disconnect your instruments one by one to isolate the faulty unit.
Failure of a group of SeaTalk instruments
• Make sure that the SeaTalk connections to non-functioning instruments are secure.
LCD shows “Code ON” when the power supply is switched on
• The CodeLock anti-theft system is operational.
Poor character definition
• Adjust the contrast.
61 ST80 Maxiview Operation & Setup
Chapter 6: EMC and Servicing Guidelines
6.1 Important information
All Autohelm equipment and accessories are designed to the best industry standards for use in the leisure marine environment.
Their design and manufacture conforms to the appropriate
Electromagnetic Compatibility (EMC) standards, but good installation is required to ensure that performance is not compromised. Although every effort has been taken to ensure that they will perform under all conditions, it is important to understand what factors could affect the operation of the product.
6.2 Installation
To avoid the risk of operating problems, all Autohelm equipment and cables connected to it should be;
• At least 1m (3 feet) from any equipment transmitting or cables carrying radio signals, e.g., VHF radios, cables and antennas. In the case of SSB radios, the distance should be increased to 2m (7ft).
• More than 2m (6ft) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element.
• The equipment should be supplied from a different battery than the one used for engine start. Voltage drops below 10V in the power supply to our products can cause the equipment to reset. This will not damage the equipment, but will cause the loss of some information and can change the operating mode.
• Genuine Autohelm cables should be used at all times. Cutting and rejoining these cables can compromise EMC performance and so should be avoided unless doing so is detailed in the installation manual.
• If a suppression ferrite is attached to a cable, this ferrite should not be removed. If the ferrite has to be removed during installation it must be reassembled in the same position.
62 ST80 Maxiview Operation & Setup
6.3 Check Before Going to Sea
• Always check the installation before going to sea to make sure that it is not affected by radio transmissions, engine starting etc.
• In some installations, it may not be possible to prevent the equipment from being affected by external influences. In general this will not damage the equipment but can lead to it resetting, or momentarily may result in faulty operation.
6.4 Servicing and Safety
• Autohelm equipment should be serviced only by authorised
Autohelm service engineers. They will ensure that service procedures and replacement parts used will not affect performance.
There are no user serviceable parts in any Autohelm product.
• Some products generate high voltages, and so never handle the cables/connectors when power is being supplied to the equipment.
• Always report any EMC related problem to your nearest Autohelm dealer. We will use any such information to improve our quality standards.
ST80 Maxiview Operation & Setup
Chapter 7: Specification
Dimensions:
Power supply:
Current consumption:
Operating temperature:
Illumination:
110 x 114.5 x 18.25mm (4.33 x
4.5 x 0.71in)
10 to 16 V DC
50 mA with illumination off
250mA with illumination full on
-10 to +70°C (14°F to 158°F)
3 level illuminated dial and LCD keypad permanently illuminated
63
64 ST80 Maxiview Operation & Setup
ST80 Maxiview Operation & Setup
Index
A
Alarm Control 56
Alarms 34
Apparent Wind Angle Page 17
Apparent Wind Speed page 17
Audible Alarms 35
Automatic CodeLock Systems 59
Average Speed 14
B
Bearing to Waypoint (BTW) Page 21
Boat Speed Page 11
C
CodeLock Security 58
Contents Setup 49
Contrast Adjustment 54
Course Over Ground (COG) & Bearing to
Waypoint (BT 22
Course Over Ground (COG) Page 20
Cross Track Error 23
Custom 48
D
Data Lost 32
Date/Time/Tide Page 25
Dead Reckoned MOB 32
Depth Chapter 15, 40
Depth Display Format 42
Depth Offset Page 16
Depth Page 15
Depth Response 41
Display Format 40, 44
E
Editing Rights 45
EMC and Servicing Guidelines 61
Enabling CodeLock 59
Entering Setup 36
G
Gaining Control of the Maxiview 10
H
I
Heading Chapter 19
Heading Page 19
Help/Setup Page 27
Illumination 31
Incomplete MOB Data 33
Instrument Setup 46
K
Keypad Beeps 10
L
Lamp Offset Adjustment 53
Lat/Lon MOB 33
LCD Inversion 55
List of Multi-line Selections 29
Log/Trip Page 13
M
Man Overboard 32
Man Overboard and Alarms 32
Manual CodeLock System 59
Maximum Speed Page 14
Minimum Depth Page 16
MOB Audible Alarm 34
Multi-Line 27
Multi-line Factory Defaults 30
Multi-line Setup 28
Multiline Chapter 44
N
Navigate Chapter 22
65
66 ST80 Maxiview Operation & Setup
O
Operating the Maxiview using the Remote
Keypad 10
P
Problem Solving 60
Q
Quitting User Setup 57
R
Race Start Page 26
Race Timer Chapter 26
Resetting the Contrast 32
Response Pages 37
S
Sail/Power/Custom Selection 47
Servicing and Safety 62
Setup 36
Setup and Calibration 7, 36
Specification 63
Speed Chapter 11, 37
Speed Over Ground (SOG) Page 12
Steering Page 20
T
Tack Course Page 21
Title Control 50
Transducers Page 46
Trend Indicator Thresholds 38, 41
True Wind Angle (Referenced to the
Compass) 19
True Wind Angle (Relative to the Vessel) 18
True Wind Speed Page (Relative to the
Vessel) 18
True/Magnetic Heading 52
V
Variation 51
Velocity Made Good (VMG) to Waypoint
Page 23
Velocity Made Good (VMG) to Wind
Page 12
W
Waypoint Data Page 24
What is CodeLock?
58
Wind Angle Response 43
Wind Chapter 17, 42
Wind Speed Response 43
81022–1
Maxiview
Raymarine Ltd.
Anchorage Park, Portsmouth,
P03 5TD, England.
Telephone: (44) (0) 2392 693611
Fax: (44) (0) 2392 694642

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Large, clear display
- Easy-to-use interface
- Waterproof
- Multifunctional
- Customizable