Advertisement
Advertisement
Alliance 855 / 888HR TREADMILL
WITH ORTHOPEDIC BELT
OWNER’S MANUAL
Alliance Fitness Treadmills
Manufactured in the USA by:
KEYS Fitness Products, LP
P.O. Box 551239
Dallas, Texas 75239
(214) 340-8888
Table of Contents
Information Page #
Table of Contents
Specification Sheet
Important Safety Information
2
3
4
Before You Start
Warm Up Exercises
Assembly Instructions
Power Requirements
Console Functions and Descriptions
Program and Operating Instructions
Program Descriptions and Profiles
Belt Adjustments and Tension
Change to MPH or KM
Troubleshooting Guide
Parts and Exploded View
Parts List
Warranty Registration (Mail In Form)
7
8
5
6
9, 10, & 11
12, 13, & 14
15
16
17
18
19
20
21
Page 2
Specification Sheet
ALL855 ALL888HR
♦ Horsepower (Continuous) 2.0hp 3.0hp
♦ Display Type 5 Window LED 5 Window LED
Green Display w/Pace Green Display w/Pace
♦ Electronics One-Touch One-Touch
♦ Pre-Set Programs 4 4
♦ Custom Programs 10 10
♦ Heartrate Programs 0 2
♦ Speed/Incline Toggles Yes Yes
♦ Speed/Incline Speed bar Yes Yes
♦ Power Incline 0-15% 0-15%
♦ Roller Diameter 2.5” 2.5”
♦ Cushioned Deck Yes Yes
♦ Speed Range 0-10mph 0-12mph
♦ Ortho-Belt Size 20x56 ” 20x56”
♦ Side Hand Rails Yes Yes
♦ Foot Print 29x71” 29x71”
♦ Warranty Motor 10 Years 10 Years
♦ Deck and Belt 5 Years 5 Years
♦ Warranty Parts 3 Years 3 Years
♦ Warranty Labor 1 Year 1 Year
♦ Warranty Frame Lifetime Lifetime
PAGE 3
Important Safety Information
♦
WARNING!
Before using this treadmill or starting any exercise program, consult your physician.This is especially important for persons over the age of 35 and/or persons with pre-existing health problems.The manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
♦
WARNING!
To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is important to review this manual and the following precautions before operation.
♦
SAFETY PRECAUTIONS AND TIPS
♦ It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar with warnings and safety precautions.
♦ This treadmill has a user maximum capacity of 400 pounds.
♦ The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not be placed in a garage, patio, or near water and should never be used while you are wet. KEYS recommends a treadmill mat be placed under the treadmill to protect floor or carpet and for easier cleaning.
♦ Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed power cord.
♦ Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with bare feet, sandals, socks or stockings.
♦ Always straddle the belt and allow it to start moving before stepping onto the belt.
♦ Hold on to handrails when adjusting speed, incline, or other controls.
♦ Always examine your treadmill before using to ensure all parts are in working order.
♦ Allow the belt to fully stop before dismounting.
♦ Pets should never be allowed near or on the treadmill.
♦ Do not leave children unsupervised near or on the treadmill.
♦ Never operate the treadmill where oxygen is being administered, or where aerosol products are being used.
♦ Never insert any object or body parts into any opening.
♦ For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time.
♦ Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these instructions will void the treadmill warranty.
♦ Never leave the treadmill unattended while it is running.
PAGE 4
Before You Start
Thank you for purchasing a KEYS treadmill! The ALLIANCE 855 and 888 treadmill was designed to meet your needs for cardiovascular exercise.
Before you start, please read the Owner’s Manual and become familiar with the operation of your new treadmill.
♦
Remember to take the time to perform the stretching exercises provided on Page 6 to avoid injury.
♦
Do not stand on the walking belt while pressing the Power button or Start/Stop button.
♦
Always adjust the speed of the treadmill in small increments as this treadmill is capable of high speeds.
♦
If you are taking medication, consult your physician to see if the medication will affect your exercise heart rate.
♦
If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the pre-set treadmill programs or start an exercise program without first contacting and receiving approval from your physician.
♦
To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console.
KEYS recommends a sealed water bottle for beverages consumed while using the treadmill.
♦
Please review the following picture below to familiarize yourself with the listed parts. This manual covers several treadmills, so the one pictured below may not be identical to your particular model.
WATER BOTTLE
HOLDER
(WATER BOTTLE NOT INCLUDED)
UPRIGHTS
READING RACK
CONSOLE
ELECTRONIC DISPLAY
SIDE HAND RAILS
MOTOR COVER
WALKING BELT
CIRCUIT BREAKER
FOOT RAILS REAR ROLLER
ADJUSTMENT BOLTS
PAGE 5
Warm Up Exercises
EXERCISE GUIDELINES
WARNING ! Before beginning this or any exercise program, you should consult your physician. This is especially important for individuals over the age of 35 or individuals with pre-existing health problems.
Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the muscles and raising body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. The photos on this page show several forms of basic stretching you may perform before your workouts. In order to achieve an adequate warm-up, perform each stretch three times.
TOE TOUCH STRETCH
Stand bending your knees slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for
15 counts, then relax. This will stretch your hamstrings, back of knees , and back.
HAMSTRING STRETCH
Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your hamstrings, lower back, and groin.
CALF/ACHILLES STRETCH
With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. To cause further stretching of the Achilles tendons, bend your back leg as well. This will stretch your calves,
Achilles tendons, and ankles.
QUADRICEPS STRETCH
With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax.
This will stretch your quadriceps and hip muscles.
INNER THIGH STRETCH
Sit with the soles of your feet together and your knees outward. Pull your feet toward your groin area as far as possible.
Hold for 15 counts, then relax. This will stretch your quadriceps and hip muscles.
PAGE 6
Assembly Instructions
Minor Assembly Required!
ALLIANCE 855/888HR treadmill is shipped in two pieces: the console upright assembly, and the base assembly. After opening the box, remove any packing materials from the treadmill. Do not throw away any packing materials until the unit is working properly. The treadmill box contains a package that includes the
Owners Manual, a RED SAFETY KEY, and a belt adjustment tool. The 888HR will also contain the heart rate chest strap. The treadmill will not operate without the Red Safety Key.
The console upright assembly is attached to the base assembly. Place the unit on a clean, level surface near an electrical outlet (extension cords are not recommended).
See Figure 1
1. Raise the console into an upright position. Loosely install both 3/4” buttonhead screws on each side of the upright. Install and tighten each 3 1/2” x 5/16” bolt (2) with washers from the bottom of the base frame through the upright lock (diag. 1).
2. Now tighten the buttonhead screws securely from step 1.
3. Install motor hood cover using 5/8” phillips head screws (8 screws).
Be sure the treadmill is level to the floor. The rear feet can be adjusted to level the treadmill.
Assembly is now complete!
Figure 1
PAGE 7
Power Requirements
ARNG!
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A
RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN
IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT
MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT THE OUTLET, HAVE
A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power.
Voltage spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an electrical rating of 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in the drawing below.
PAGE 8
Console Functions and Descriptions
PROGRAM BUTTONS - These buttons are used to access each of the four programs: Fat Burn, Cardio,
Warm Up, and Cross Training. Each program has one preset program, and two additional custom programs in the P1 and P2 mode. See the “Program and Operating
Instructions” on page 12.
START/STOP - This button starts the treadmill belt moving. There is a 4 second countdown built in as a safety feature to let you know the treadmill belt is about to start moving.
Use the START/STOP button also to stop your treadmill after your workout. The belt will gradually come to a stop after pressing the button.
POWER - Press to on. Allow
6-8 seconds while the electronics perform a self check prior to pressing other buttons.
ENTER - Use the Enter button while setting program time, speed, and incline options.
See page 12 for complete instructions.
PAUSE - Press to temporarily pause your workout while in use. The treadmill is designed with an automatic power off feature after 5 minutes in the pause mode.
ONE TOUCH INCLINE
BAR - Use to either increase or decrease the incline. Each number indicates percent of grade. Pressing one of the buttons will gradually increase or decrease the incline to the new setting.
CONSOLE SAFETY KEY - Place the RED
Safety Key here prior to turning power on.
THE TREADMILL WILL NOT OPERATE
WITHOUT THE SAFETY KEY ATTACHED.
The safety key is equipped with a string and clip that will clip to your clothing. This is an important safety feature that will automatically turn the power off if you should trip or fall while using the treadmill.
INCLINE - Use to either increase (UP arrow) or decrease (DOWN arrow) the incline. These buttons are also used while programming INCLINE.
ONE TOUCH SPEED BAR -
Use to either increase or decrease the speed. Each number indicates MPH.
Pressing one of the buttons will gradually increase or decrease the speed to the new setting.
SPEED - Use to either increase (UP arrow) or decrease (DOWN arrow) the speed. These buttons are also used while programming SPEED and
TIME.
PAGE 9
Console Functions and Descriptions
There are five display windows on the control panel to provide feedback information.
WORKOUT TIME/PACE WINDOW
♦
TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds)
♦
INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to
0 seconds
♦
PACE: Indicates amount of time required to complete 1 mile at current speed.
SPEED WINDOW
♦
SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments
DISTANCE / CALORIES WINDOW
♦
DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at
10.0
♦
CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and time
INCLINE WINDOW
♦
INCLINE: Indicates incline in percent of grade 0-12% in .5 increments
PAGE 10
Console Functions and Descriptions
INCLINE WINDOW
♦ INCLINE: Indicates incline in percent of grade 0-12% in 1 increments
♦ PULSE (888HR Model Only): Indicates current heart rate
♦ H E AR T (888HR Model only): Indicates control panel is receiving a signal from heart rate transmitter. Heart will blink on and off if receiving signal from Heart Rate Transmitter chest strap.
♦
CENTER BRICKYARD WINDOW
♦ Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode, shows the change in speed profile across the interval range (1-10) and shows position with a blinking action.
♦ The 880HR will display the name of the program selected, showing on the left hand side of the window. The LAP counter will appear in manual mode in the center of the window.
♦
SPEED & INCLINE “ONE-TOUCH” BUTTONS
♦ Easy One-Touch buttons for Speed and Incline have been added to the console. To increase or decrease the speed, simply choose the desired setting (each number 2 through 8 represents Miles per Hour). To increase or decrease the amount of incline, simply choose the desired setting (each number 2 through 8 represents percent grade).
PAGE 11
Program and Operating Instructions
♦
QUICK START / MANUAL MODE
♦ Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
♦ ATTACH THE RED SAFETY KEY TO CENTER OF CONSOLE .
♦ Stand on the treadmill and straddle belt.
♦ Press POWER button. The TIME window will flash.
♦ Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving. Speed or incline may be adjusted by using the appropriate UP (increase) or DOWN (decrease) buttons. Speed and Incline can also be adjusted using the “One Touch” buttons labeled 2 through 8, or by using the toggle switches located on the handlebars.
For speed and incline adjustments while using the treadmill, try the convenient handlebar toggles switches. The left handlebar switch is for incline, while the right handlebar switch adjusts the speed.
♦ To end your workout , press START/STOP button. Belt will gradually slow to zero.
♦ To pause your workout , press PAUSE. The treadmill will automatically shut off after five (5) minutes.
♦ To re-start after pausing : Press the PAUSE button. WARNING : The treadmill belt will resume at the speed the treadmill was moving before pausing.
♦ Countdown Time, Preset Speed and/or Incline : Time, Speed, and Incline may be preset prior to getting started. After pressing the POWER button, the time window will blink. Use the SPEED UP or DOWN arrows to select your workout time, then press the ENTER PROGRAM button located on the left hand side of the console below the program buttons. The
SPEED window will now be flashing. Using the same + or – arrows, select the speed for your workout, then press ENTER
PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or – arrows to set your workout incline, then press ENTER PROGRAM. To start, press the START/STOP button.
PAGE 12
Program and Operating Instructions
♦
PROGRAM MODE
♦ Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
♦ ATTACH THE RED SAFETY KEY TO THE CENTER OF THE CONSOLE .
♦ Stand on the treadmill and straddle belt.
♦ Press POWER button. The TIME window will flash.
♦ There are three (4) pre-set programs on the 855 and 888HR. Both include Fat Burn, Cardio, and Warm Up programs. Select the program by pressing the appropriate button.
♦ Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving.
♦ Each of the pre-set programs (4) can also be customized. Follow the instructions below for your particular model.
♦ Customizing programs in P1 and P2 Mode: Each pre-set program can be customized in the P1 or P2 mode. After making the program selection, the CALORIE/DISTANCE window will read “OP.” ”OP” refers to “original program” and is preset.
Press the same program button once more, and the CALORIE/DISTANCE window will read P1. The “P1” mode is now accessed. You can now program the Time, Speed, and Incline in P1 mode, which will save your entered information for future use. The time window will blink. Use the SPEED UP or DOWN arrows to select your workout time, then press the ENTER
PROGRAM button located on the left hand side of the console below the program buttons. The SPEED window will now be flashing. Using the SPEED UP or DOWN arrows, select the speed for your workout, then press the ENTER PROGRAM button.
Now the INCLINE window will be flashing. Use the INCLINE UP or DOWN arrows to set your workout incline, then press the
ENTER PROGRAM button. To start, press the START/STOP button. To access P2 mode, press the selected program button three times (once for OP, twice for P1, three times for P2). Follow the above procedure to customize.
♦ TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed the P1 or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For instance, if P1 in Fat Burn has been programmed, to change to a new setting, press the Fat Burn button twice to access P1. Then press the PAUSE button to get the TIME window to flash. Follow the directions above to continue to change the program.
PAGE 13
Program and Operating Instructions
♦
Heart Rate Control Instructions (888HR only)
♦
HEART RATE PROGRAM MODE
♦ The Heart Rate program is designed to keep your heart rate a desired level of “beats per minute” by automatically adjusting the incline. For example, if you have programmed in a desired heart rate of 105 beats per minute and your heart rate is only
95 beats per minute (you must be wearing Heart Rate Transmitter), the incline will automatically increase to intensify the work load, and increase you heart rate to the 105 beats per minute you programmed.
♦ If your heart rate is above your programmed amount of beats per minute the incline will automatically decrease to lower your heart rate. You may at any time during the Heart Rate Program adjust/override the speed and or incline by simply pressing the correct corresponding buttons. You may change your “Target Heart Rate” at any time during the program by pressing the TARGET + or TARGET – buttons.
♦ Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). Attach Safety Key to console
♦ Place the Heart Rate transmitter strap across chest against the skin. Stand on the treadmill and straddle belt.
♦ Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can be entered.
The TIME window will flash. The “Heart” shape on the treadmill will be flashing if the Heart Rate Transmitter is transmitting. Adjust the strap on the chest until the console is picking up a signal.
♦ For Quick Start, press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease) buttons. Heart rate will read out in the Incline window.
♦ To select the Heart Rate Control program, press the “Heart Rate Program” button.
♦ The incline window will flash “125”, which is the default program target heart rate.
♦ Adjust Target Heart Rate to desired level with the TARGET + or – buttons.
♦ Press START/STOP button, or continue instructions below to program Time, and Speed.
♦ You can now program the Time and Speed. The time window will blink. Use the SPEED + or – arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED window will now be flashing. Using the SPEED + or – arrows, select the maximum speed for your workout, then press ENTER PROGRAM. To start, press the START/STOP button.
PAGE 14
Program Profiles
6
5
4
3
2
1
12
11
10
9
8
7
SPEED
INCLINE
1 2 3 4 5 6 7 8 9 10
The Fat Burn Program is designed to vary the treadmill elevation, while maintaining a constant walking belt speed.
3
2
1
9
8
7
6
5
4
12
11
10
SPEED
INCLINE
1 2 3 4 5 6 7 8 9 10
The Cardio Program is designed to vary the treadmill Speed, while maintaining a constant Elevation.
6
5
4
3
2
1
12
11
10
9
8
7
SPEED
INCLINE
1 2 3 4 5 6 7 8 9 10
The Warm Up Program is designed to gradually increase the treadmill Speed and
Elevation in the first segment (warm up) and gradually decrease the treadmill Speed and Elevation in the last segment (cool down). This is also known as a
Plateau program.
7
6
5
4
3
2
1
12
11
10
9
8
SPEED
INCLINE
1 2 3 4 5 6 7 8 9 10
The Cross Training Program is designed to control the walking belt speed and elevation inversely in alternating segments.
PAGE 15
Belt Adjustment and Tension
WARNING! Do not overtighten rollers! This will cause premature roller bearing failure!
Belt adjustment and tension performs two functions: adjustment for tension and centering. Your new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the procedures below if the belt shifts to the left or right or while walking:
WALKING BELT IS SHIFTING TO THE LEFT (Diagram 1)
First, turn treadmill on to run at 1 mph. Using the hex key provided, turn the left rear roller adjustment bolt ¼ turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions.
WALKING BELT IS SHIFTING TO THE RIGHT (Diagram 2)
First, turn the treadmill on to run at 1 mph. Using the hex key provided, turn the right rear roller adjustment bolt ¼ turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions.
WALKING BELT IS SLIPPING DURING USE (Diagram 3)
First, unplug the power cord from the surge protector. Using the hex key provided, turn both left and right rear roller adjustment bolts the same distance, usually a ¼ turn in the clockwise direction. Plug the power cord back into the surge protector and run the treadmill at
2.5 mph. You should now walk on the belt to determine if the belt is still slipping. Repeat the above procedure until the walking belt is not slipping. The tension should be just tight enough not to slip.
Turning the hex key counter clockwise brings the rear rollers and belt towards you. Turning the hex key clockwise pushes the rear roller and belt away form you.
PAGE 16
Change Miles per hour to Kilometers per hour
Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). All treadmills are calibrated at the factory for British Units (miles per hour). To change the display to read in kilometers, follow the steps described here:
1) Turn power OFF on the console. (Do not unplug treadmill) Attach the magnet safety key to the console.
2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in the backside of the console (see diagram below).
3) Depressing the calibration mode switch ONCE; CL11 should appear in the TIME window.
4) Pressing the SPEED +/- button will activate your choice.
5) To accept the setting, press the POWER button.
Page 17
Troubleshooting Guide
Treadmill will not start.
1) Is the RED Safety Key Attached to the Console?
2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements”)
3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped. Wait five minutes and then press the switch back in.
4) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in. If it has tripped, reset or have an electrician replace the breaker in home.
5) Have an electrician check for inadequate voltage at the outlet.
Treadmill looses power during use.
1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped. Wait five minutes and then press the switch back in.
2) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in. If it has tripped, reset or have an electrician replace the breaker in home.
3) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slows during use.
1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15 amps, with a
14-guage cord of five feet or less and the surge protector is securely plugged into the outlet.
2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slips or is not centered on rear roller.
1) Refer to “Belt Adjustment and Tension” section.
2) Need help? Call Keys Technical Service at (888) 340-0482.
Treadmill Error Messages.
2)Your treadmill is equipped with a software package that enables error messages to be displayed when there is a problem. To avoid possible damage to the treadmill and the possibility of injury, do not operate the treadmill until the problem is corrected. Call Keys Technical Service at (888) 340-0482.
Parts & Exploded View
1 Left Side Extrusion Rail
2 Right Side Extrusion Rail
3 Treadmill Belt
4 Front Roller Assembly
5 Rear Roller
6 Treadmill Deck
7 Left End Cap
8 Right End Cap
9 Rear Adjustable Foot (2)
10 Main Frame
11 Bottom Motor Pan
Part #
05-0028
05-0028
04-0014
24-0106
09-0009
03-0008
06-0043
06-0042
10-0008 various
06-0041
12 Front Wheel (2)
13 Uprights for Console (2)
14 Motor Hood Cover Top
15 Motor Drive Belt
16 Motor (855)
Motor (888HR)
17 Elevation Motor (acuator)
18 Console Assembly (855)
19 Console Assembly (888HR)
20 Handlebars
21 Toggle switches (2)
22 Lower Electronics M/Control P/Supply
(855)
22 Lower Electronic M/Control P/Supply
(888HR)
Part #
06-0039 various
06-0040
04-0007
12-0004
12-0026
12-0026
24-0191
24-0192 various
08-0027
08-0050
08-0016
Page 19
ALL855OB- Parts List
PART #
02-0009
02-0016
02-0017
02-0019
02-0021
02-0022
DESCRIPTION
02-0004 SCREW-8x5/8 PHIL PH AB BLACK
02-0005 SCREW-8x5/8 PPH HILO BLACK TPB
02-0007 NUT 5/16-18 NYLOCKZP
NUT-HEX 5/16 WIZ-FL-LK-ZP
02-0013 WASHER LOCK 1/4"
02-0014 BOLT-HEX 1/4-20x2 1/2" GRADE 5 ZP
BOLT-HEX 3/8-16x2 1/2" GRADE 5
NUT-NYLOCK HEX 3/8-16
BOLT-CARRIAGE 10-24x1 1/2
WASHER 9/32 5/8 1/8THICK ZP
NUT-NYLOCK HEX 10-24
QTY PART # DESCRIPTION
9 08-0004 BREAKER-CIRCIT-15AMP
11 08-0112 MEBRANE LED FOR WEDGE CONSOLE
2 08-0088 MEMBRANE-LED/LCD OWER
4 08-0027 SWITCH-REMOTE-W/HARNESS
16 08-0047 ENCODER-OPTICAL-ALEPH
2 08-0077 CORE-ERRITE
1 08-0050 CONTROLLER-REPLACES 08-0013
2 09-0008 ROLLER-DRIVE .5:-8800/8500
4 09-0009 ROLLER-IDLER 2.5"-8800/8500
2 10-0002 ISOLATOR-BOARD 3/4"
4 10-0008 FOOT-REAR-KEYS SERIES
2 10-0017 TAPE-FOAM-1"X75ft
4 10-0021 MOLDED GRIP OVAL NEW
16 11-0002 BUSHING-REAR ELEVAION
1 11-0012 FLYWHEEL 5.88 10J-1.250 REPLACES 11-
1 12-0004 MOTOR-MAGNETEK 2.0HP-223526
1 12-0026 ACTUATOR-600# BOSS
02-0024 CARRIAGE BOLT 5/16x1 GRADE 5 ZP
02-0027 NUT-T HF 14209H-DB
02-0028 SWITCH-MAGETIC KILL-YIHAN
02-0030 SCREW-HEX TRILOBE 8-32x1/2"
02-0031 BOLT-HEX 3/8-16x1 3/4" GRADE 5ZP
02-0036
02-0038
02-0042
02-0050
02-0082
02-0084
02-0085
02-0090
02-0095
02-0099
SCREW-PPH 8x5/8 GREEN HEAD
WRENCH-ALLEN 3/16 SHAFT ARM
SCREW#8x5/8' SD BLACK
NUT-NYLOCK HEX 1/4-20
SCREW-BUTTON HEAD 5/16-18x2 1/2'
BOLT-CARRIAGE 5/16x:RADE 5
HEX NUT 1/2-13
HEX BOLT 1/4-20x1 3/4 HC
SCREW-BUTTON HD 5/16-18x1" HSC BLK
WASHER -SFW 3/8X7/8X1/8" THICK
02-0100 BOLT HEX 5/16-18x3 1/2"GRADE 8
02-0105 INDRTY-5/16-18 HEAVY WAL AVK
02-0119 HEX SCREW HD 1/4-20x3 1/4"
02-0125 SCREW-5/16-18x3/4"BUTTON HD BLACK
02-0131 HEX NUT 5/16-18
02-0137 PLUG PUSH-IN
02-0141 PUSH NUT BLACK.112 SHAFT
02-0143 HEX BOLT 1/4-20x1"
03-0008 WALKBOARD KEYS SERIES NOTCHED
04-0007 BELT-POLY V-260J10-KEYS SERIES
04-0014 WALKBELT ORTHO 19.75x116.5-P7 2 PLY
05-0028 EXTRUSION SIDE BOARD LT&RT
06-0014 BUSHING-STRAIN RELIEF #1237
06-0016 TIES-WIRE
06-0021 CLAMP WIRE 3367 7/16
06-0024 CLIP-ALLEN WRENCH
06-0038 PULLEY-KEY SERIES-4.5"
06-0039 WHEEL-KEYS SERIES-2.5"
06-0040 MOTOR COVER
06-0041 PAN-BOTTOM
06-0042 ENDCAP-RIGHT
06-0043 ENCAP-LEFT
3 13-0011 CORD-POWER-90"
1 13-0014 WIRE-JUMPER 12"-220V-KEYS SERIES
2 13-0020 HARNESS CONTROLLER 80"
4 13-0034 WIRE-MOTOR LEAD EXTENSION 8"
2 13-0040 HARNESS CONTROL PANEL +6"
2 14-0026 DECAL-WARNING CONSOLE-ALL GRAY
4 14-0027 DECAL-EMERGENCY STOP-RED
2 14-0354 OVERLAY CONSOLE ALL855-OB
2 14-0205 DECAL DISCONNECT-MOTOR COVER
1 14-0226 DECAL-SIDE FRAME-EC850
2
2
8
2
3
2
6
8
1
14-0321
14-0336
14-0351
14-0352
15-0029
15-0080
16-0018
16-0017
16-0020
DECAL-10YR MOTOR WARRANTY
DECAL MTR COVER ALL ALLIANCE
DECAL SPEED SERIGRAPH
DECAL INCLINE SERIGRAPH
DIAGRAM-WIRING-MAGNETEK
MANUAL-EC880HR-EC850
BOX-BOTTOM-KEYS SERIES
BOX-TOP KEYS/SCIFIT
PAD-TOP TRAY-KEYS SERIES
1 16-0033 ANGLE FOAM-6FT PIECES-CUT INTO 9PCS
1 16-0039 PAD END EC850/880
2
1
7
1
1
1
2
1
1
16-0040
16-0041
16-0043
16-0061
16-0062
17-0015
17-0016
17-0017
17-0018
PAD SIDES EC850/880
PAD HANDRAILS EC850/880
BOX-TOP INVERTED 16-0017
ANGLE BOARD 6"
ANGLE BOARD 33 3/4"
RECT 1x1 1/2x11GAx25 15/16
RECT 1x1 1/2x12GAx26 7/16
RECT 1x3x12GAx26 7/16
RECT 1x3x12GAx166
1 17-0020 RECT 1x2x12GAx4 7/16-PUNCHED
1 17-0021 RECT 1x2x12GAx3 9/16
06-0071 FAN 5"-5/8" ID
06-0084 BAG-PLASTIC 12x12 3MIL-INST PACKET
2 17-0022 RECT 1x2x12GAx23 7/8
1 17-0040 OVAL 1.094x2x16GAx17.25
06-0118 PLASTIC SWITCH HOUSING BLK FOR OVAL 2 17-0046 TUBE-RESET GUIDE
06-0140 INSERT LED FOR CONSOLE 1 17-0052 RECT-2x4x14GAx100"
06-0160 CONSOLE ALLIANCE SHELL LED/LCD 1 17-0053 RECT-1x3x16GAx24 7/16"
07-0050 ELECTRONICS 5 WIN LED GREEN 1
QTY PART # DESCRIPTION
1 19-0015 BRACKET-MOTOR COVER
1 19-0019 GUIDE BELT GLAVANIZED
1 19-0030 SPACER-ENCODER
2 19-0042 BRKT-SIDE FRAME ACTUATOR
1 19-0043 BRKT-MOTOR MOUNT
1 19-0044 BRKT-ACTUATOR SUPPORT
1 19-0047 BRKT-ELEVATION ACTURATOR
1 19-0048 BRKT-REAR ROLLER
1 19-0050 BRKT-ACTUATOR BRACE
8 19-0052 BRKT-ELEVATION ACTURATOR
2 19-0057 BRKT-CHANNEL SUPPORT BOSS
1 19-0062 BRKT-ACTUATOR
2 19-0064 BRKT-STRAIN RELIER/BREAKER
4 19-0065 BRKT-UPRIGHT BRACE
1 19-0079 BRKT-BELT GUIDE
1 19-0089 PLATE CONTROLLER KEYS8500
1 19-0101 BRKT-CONSOLE BRACE
1 19-0107 SLUG-EMERGENCY STOP RED
1 19-0128 BRKT-RIGHT STABILIZER
1 19-0129 BRKT-LEFT STABILIZER
1 19-0130 PLATE-CONSOLE ALLI-14GA-EC850/880
1 19-0131
1 19-0132
1 19-0151
1 19-0152
BRKT-RIGHT FILLER
BRKT-LEFT FILLER
BRKT-RT U/R STIFFENER
BRKT RT U/R & FRT ROLLER
1 19-0153 BRKT LT U/R & FRT ROLLER
2 19-0154 BRKT MOTOR SHELF REVISED 19-0088
1 19-0160 BRKT MOTOR COVER SUPPORT
3 20-0019 PROC-BELT GUIDE TB 17-0017
1 20-0020 PROC-FRAME TUBE 17-0018
1 20-0023 PROC-LOWER ELEVATION END TB 17-0021-OBS
1 20-0027 PROC-FRAME BRACE 17-0016
1 20-0060 PROC-RT CURVED U/R 17-0052
1 20-0061
1 20-0066
PROC-LT CURVED U/R 17-0052
PJROC OVAL HBAR NEW 17-0040
1 20-0102 PROC LOWER ELEV END TB REVISED
1 21-0012 ELEVATION X-TB-NOTCHED BOTH ENDS
2 21-0028 RT CURVED UPRIGHT-WELD TAB
2 21-0029 LT CURVED UPRIGHT-WELD TAB
1 21-0030 UPRIGHT STIFFENER
1 21-0031 STRAIGHT U/R SAW CUT TO 2 PIECES
4 21-0031 STRAIGHTENED U/R SAW CUT TO 2 PIECES
4 22-0013 LOWER ACTUATOR SUB-ASSEMBLY
1 22-0026 UPPER ACTUATOR ASSEMBLY
1 22-0051 99"CONSOLE ASSEMBLY
1 22-0059 RT U.R BRKT SUB-ASSEMBLY
1 22-0060 LT U/R BRKT SUB-ASSEMBLY
2 23-0038 DECK FRAME ASSEMBLY
2 23-0066 UPRIGHT ASSEMBLY-ALLIANCE/BOSS
1 24-0106 FRONT ROLLER ASSEMBLY-LEYS8800/8500
2 24-0191 CONSOLE ASSEMBLY ALL855-OB
1 26-0059
1
1
INST PACKET-EC850
Page 20
ALL888HR-OB- Parts List
PART # DESCRIPTION
02-0004 SCREW-8x5/8 PHIL PH AB BLACK
02-0005 SCREW-8x5/8 PPH HILO BLACK TPB
02-0007 NUT 5/16-18 NYLOCKZP
02-0009 NUT-HEX 5/16 WIZ-FL-LK-ZP
02-0013 WASHER LOCK 1/4"
02-0014 BOLT-HEX 1/4-20x2 1/2" GRADE 5 ZP
02-0016 BOLT-HEX 3/8-16x2 1/2" GRADE 5
02-0017 NUT-NYLOCK HEX 3/8-16
02-0019 BOLT-CARRIAGE 10-24x1 1/2
02-0021 WASHER 9/32 5/8 1/8THICK ZP
02-0022 NUT-NYLOCK HEX 10-24
02-0023 CLIP-ROTO HW12
02-0024 CARRIAGE BOLT 5/16x1 GRADE 5 ZP
02-0027 NUT-T HF 14209H-DB
02-0028 SWITCH-MAGNETIC KILL-YIHAN
02-0030 SCREW-HEX TRILOBE 8-32x1/2"
02-0031 BOLT-HEX 3/8-16x1 3/4" GRADE 5ZP
02-0036 SCREW-PPH 8x5/8 GREEN HEAD
02-0038 WRENCH-ALLEN 3/16x7/8x1/8x1' HSC
02-0042 SCREW#8x5/8' SD BLACK
02-0050 NUT-NYLOCK HEX 1/4-20
02-0058 WASHER-FLAT NYLON 3/8
02-0065 SCREW-SHCS 1/4-20x1 3/4"
02-0079 SCREW-BUTTON HD#14-14x1" 5/32 SH AB
02-0082 SCREW-BUTTON HEAD 5/16-18x2 1/2'
02-0084 BOLT-CARRIAGE 5/16x:RADE 5
02-0085 HEX NUT 1/2-13
02-0090 HEX BOLT 1/4-20x1 3/4 HC
02-0095 SCREW-BUTTON HD 5/16-18x1" HSC BLK
02-0099 WASHER -SFW 3/8X7/8X1/8" THICK
02-0100 BOLT-HEX 5/16-18x3 1/2" GRADE 8
02-0105 INSERT-5/16-18 HEAVY WAL AVK
02-0119 HEX SCREW HD 1/4-20x3 1/4"
02-0125 SCREW-5/16-18x3/4"BUTTON HD BLACK
02-0131 HEX NUT 5/16-18
02-0137 PLUG PUSH-IN
02-0143 HEX BOLT 1/4-20x1"
03-0008 WALKBOARD KEYS SERIES NOTCHED
04-0007 BELT-POLY V-260J10-KEYS SERIES
04-0014 WALKBELT ORTHO 19.75x116.5-P7 2 PLY
05-0028 EXTRUSION SIDE BOARD LT&RT
06-0014 BUSHING-STRAIN RELIEF #1237
06-0016 TIES-WIRE
06-0024 CLIP-ALLEN WRENCH
06-0038 PULLEY-KEY SERIES-4.5"
06-0039 WHEEL-KEYS SERIES-2.5"
06-0040 MOTOR COVER
06-0041 PAN-BOTTOM
06-0042 ENDCAP-RIGHT
06-0043 ENCAP-LEFT
06-0058 SUPPORT-PC BOARD HRC
06-0071 FAN 5"-5/8" ID
06-0084 BAG-PLASTIC 12x12 3MIL-INST PACKET
06-0118 PLASTIC SWITCH HOUSING BLK FOR OVAL
06-0140 INSERT LED FOR CONSOLE
06-0160 CONSOLE ALLIANCE SHELL LED/LCD
07-0020 RECEIVER-DISCRETE-LED HRC
1 11-0002
3 11-0008
2 11-0009
2 12-0013
6 12-0026
2 13-0011
2 13-0014
1 13-0017
2 13-0020
4 13-0040
4 14-0026
2 14-0027
2 14-0355
2 14-0205
2 14-0225
2 14-0321
QTY PART #
9 08-0004
11 08-0016
2
4 08-0027
16 08-0047
2 08-0077
1 08-0052
2 08-0089
4 08-0111
6 08-0123
4 09-0008
2 09-0009
4 10-0002
16 10-0008
1 10-0017
1 10-0021
DESCRIPTION
BREAKER-CIRCIT-15AMP
CONTROLLER-MOTOR 3525HE
SWITCH-REMOTE-W/HARNESS
ENCODER-OPTICAL-ALEPH
CORE-ERRITE
CONTROLLER-REPLACES 08-0016
MEMBRANE-LED/LCD POWER
BUSS WIRE 20GA
MEMBRANE 5WIN LED FROG WEE/ALL
ROLLER-DRIVE 2.5"- 8800/8500
ROLLER-IDLER 2.5"-8800/8500
ISOLATOR-BOARD 3/4"
FOOT-REAR-KEYS SERIES
TAPE-FOAM-1"X75ft (20FT)
MOLDED GRIP OVAL NEW
BUSHING-REAR ELEVAION
FLYWHEEL-KEYS SERIES
PULLEY-DRIVE-KEYS-SERIES
MOTOR-MAGNETEK 3.0HP-223615 BOSS
ACTUATOR-600# BOSS
CORD-POWER-90"
WIRE-JUMPER 12"-220V-KEYS SERIES
HARNESS-TELCO-HRC
HARNESS CONTROLLER 80"
HARNESS CONTROL PANEL +6"
DECAL-WARNING CONSOLE-ALL GRAY
DECAL-EMERGENCY STOP-RED
OVERLAY CONSOLE ALL888HR-OB
DECAL DISCONNECT-MOTOR COVER
DECAL-SIDE FRAME-EC888HR
DECAL-10YR MOTOR WARRANTY
8 14-0336 DECAL MTR COVER ALL ALLIANCE
2 14-00351 DECAL SPEED NEW OVAL GRIPS
2 14-0352 DECAL INCLINE NEW OVAL GRIPS
2 14-0289
8 15-0029
1 15-0080
1 16-0018
1 16-0017
2 16-0020
STICKER HEART RATE ACUMEN
DIAGRAM-WIRING-MAGNETIK
MANUAL-EC880HR-EC850
BOX-BOTTOM-KEYS SERIES
BOX-TOP KEYS/SCIFIT
PAD-TOP TRAY-KEYS SERIES
1 16-0039
7 16-0040
1 16-0041
1 16-0043
2 16-0061
PAD END EC850/880
PAD SIDES EC850/880
PAD HANDRAILS EC850/880
BOX-TOP INVERTED 16-0017
ANGLE BOARD 6"
1 16-0062
1 17-0015
1 17-0016
1 17-0017
2 17-0018
2 17-0020
1 17-0021
2 17-0022
ANGLE BOARD 33 3/4"
RECT 1x1 1/2x11GAx25 15/16
RECT 1x1 1/2x12GAx26 7/16
RECT 1x3x12GAx26 7/16
RECT 1x3x12GAx166
RECT 1x2x12GAx4 7/16-PUNCHED
RECT 1x2x12GAx3 9/16
RECT 1x2x12GAx23 7/8
1 17-0033 RECT 1x2x16GAx4 1/4-PUNCHED
1 17-0040
1 17-0046
OVAL 1.094x2x16GAx17.25
TUBE-RESET GUIDE
3 20-0061
1 20-0066
1 20-0102
1 21-0012
1 21-0028
1 21-0029
1 21-0030
1 21-0031
1 22-0026
2 22-0051
2 22-0059
1 22-0060
1 23-0017
4 23-0048
4 24-0106
1 24-0191
1 24-0192
1 26-0055
1
2
2
4 19-0107
1 19-0128
1 19-0129
1 19-0130
1 19-0131
1 19-0132
1 19-0151
1 19-0152
1 19-0153
1 19-0154
1 19-0160
1 20-0019
1 20-0020
1 20-0023
2 20-0027
1 20-0060
QTY PART #
1 17-0053
1 19-0019
19-0030
2 19-0042
1 19-0043
1 19-0044
1 19-0047
1 19-0048
1 19-0050
1 19-0052
1 19-0057
1 19-0062
8 19-0064
2 19-0065
1 19-0079
2 19-0101
1
1
2
1
DESCRIPTION
RECT-1x3x16GAx24 7/16"
GUIDE BELT GLAVANIZED
SPACER-ENCODER
BRKT-SIDE FRAME ACTUATOR
BRKT-MOTOR MOUNT
BRKT-ACTUATOR SUPPORT
BRKT-ELEVATION
BRKT-REAR ROLLER
BRKT-ACTUATOR BRACE
BRKT-ELEVATION ACTURATOR
BRKT-CHANNEL SUPPORT BOSS
BRKT-ACTUATOR
BRKT-STRAIN RELIER/BREAKER
BRKT-UPRIGHT BRACE
BRKT-BELT GUIDE
BRKT-CONSOLE BRACE
SLUG-EMERGENCY STOP RED
BRKT-RIGHT STABILIZER
BRKT-LEFT STABILIZER
PLATE-CONSOLE ALLI-14GA-EC850/880
BRKT-RIGHT FILLER
BRKT-LEFT FILLER
BRKT-RT U/R STIFFENER
BRKT RT U/R & FRT ROLLER
BRKT LT U/R & FRT ROLLER
BRKT MOTOR SHELF REVISED 19-0088
BRKT MOTOR COVER SUPPORT
PROC-BELT GUIDE TB 17-0017
PROC-FRAME TUBE 17-0018
PROC-LOWER ELEVATION END TB 17-0021-OBS
PROC-FRAME BRACE 17-0016
PROC-RT CURVED U/R 17-0052
PROC-LT CURVED U/R 17-0052
PJROC OVAL HBAR NEW 17-0040
PROC LOWER ELEV END TB REVISED
ELEVATION X-TB-NOTCHED BOTH ENDS
RT CURVED UPRIGHT-WELD TAB
LT CURVED UPRIGHT-WELD TAB
UPRIGHT STIFFENER
STRAIGHTENED U/R SAW CUT TO 2 PIECES
UPPER ACTUATOR ASSEMBLY
99"CONSOLE ASSEMBLY
RT U.R BRKT SUB-ASSEMBLY
LT U/R BRKT SUB-ASSEMBLY
DECK FRAME ASSEMBLY
ELEVATION ASSEMBLY
FRONT ROLLER ASSEMBLY-LEYS8800/8500
CONSOLE ASSEMBLY ALL855-OB
CONSOLE ASSEMBLY ALL888HR-OB
INST PACKET-EC880HR
Page 21
Alliance 855 and 888HR Treadmills manfactured by KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTY
PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.
This Limited Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the
ALLIANCE brand name. The warranty period to the original purchaser is (lifetime) on the frame, (10) years on the motor, (5) years on the walking belt, and deck, (3) years on parts, and (1) year labor. This warranty does not cover wear and tear, only manufacturer defects for the periods specified.
Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller is free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your proof of the date of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product from you. It excludes expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Keys Fitness authorized dealer/technician unless otherwise authorized by Keys Fitness in writing (if anyone other than a Keys Fitness authorized dealer/technician assembles a Keys Fitness treadmill the warranty will be void unless accompanied by written authorization by Keys Fitness). Select models do not require assembly, and the original purchaser
During the warranty period Keys will at no additional charge, repair or replace (at Keys’ option) the part or product if it becomes defective, malfunctions, or otherwise fails to conform with this Limited Warranty under normal non-commercial, personal, family or household use. In repairing the Product, Keys may replace defective parts, or at the option of Keys, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and Products replaced under this warranty will become the property of Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty.
To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts determined to be defective must be returned to Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or returned. You assume the risk of loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty.
This warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does not extend to any
Product that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or (e) as a result of service by anyone other than Keys, or an authorized
Keys warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any Product be submitted for warranty service be found ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Keys’ receipt of payment or acceptable arrangements for payment.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS
LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS
NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR
EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to assume for it any other express warranty.
PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR
TREADMILL WITH KEYS FITNESS PRODUCTS, LP. MADE IN THE USA. Thank you for your business! PLEASE MAIL
WARRANTY CARD TO: KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355
.
KEYS FITNESS TREADMILL WARRANTY REGISTRATION
TELEPHONE
FIRST M.I. LAST
ADDRESS
CITY
APT. NO.
STATE ZIP
DATE OF PURCHASE MODEL NO. SERIAL NO.
Name of store or company where purchased:
How do you plan to use the treadmill?
Walk____ Run_____ Both_____
Who will use the treadmill?
Male____ Female_____ Both_____
How many family members? _____
AGE: 15-24____ 25-34____
35-44____ 45-54____
55-64____ 65 +_____
Where did you learn about treadmills?
TV____ Radio____ Friend____
In Store Display____ Salesperson___
Print ad/flyer____ Internet______
Why did you purchase a treadmill?
Dr.’s Orders____ Loose Weight____
In-home convenience____
Improve Cardiovascular Fitness___
Safety from outdoors____
Other __________________________
How important are each feature:
Least Most
Unique Features
Horsepower
Warranty
Price
Look/Design
Folding Feature
Other Comments:
_______________
_______________
_______________
_______________
KEYS FITNESS respects the rights of your privacy. Our company will not sell or distribute to others the information above. This information is used to track our product quality and to contact you in the event of a product safety concern. It may be used to offer you future Keys products only through the mail. Please check here if wish not to receive any additional information on Keys products.

Public link updated
The public link to your chat has been updated.
Advertisement