Coopers 10477 Instructions For Use Manual

PDF

Document

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

Power Details: Rated voltage (adaptor) AC 100 – 240 a.c.; 50-60Hz, 0.3A

Adaptor output DC 6V 1.5A

Rated voltage (radio) DC 6V (1.5V x 4 AA)

Power consumption 9W

Audio output

Frequency details: DAB 174-240MHz

2x2W RMS

FM 87.5-108MHz

Accessories: AC/DC Adapter

Please read this instruction manual thoroughly before starting and ensure you are familiar with the operation of your new Digital Radio & Alarm Clock.

TO CHECK DAB RADIO COVERAGE FOR YOUR AREA PLEASE ENTER YOUR POST CODE IN THE FOLLOWING

WEBSITE HTTP://WWW.UKDIGITALRADIO.COM/COVERAGE/POSTCODESEARCH/

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

SAFETY INSTRUCTIONS:

WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED:



TO PROTECT AGAINST ELECTRIC SHOCK, DO NOT IMMERSE CORD, PLUG OR APPLIANCE IN WATER OR ANY

OTHER LIQUID.



UNPLUG FROM THE MAINS SOCKET OUTLET WHEN NOT IN USE AND BEFORE CLEANING.



DO NOT OPERATE ANY APPLIANCE WITH A DAMAGED CORD OR PLUG OR AFTER THE APPLIANCE

MALFUNCTIONS OR HAS BEEN DAMAGED IN ANY MANNER. WE RECOMMEND THAT THE POWER CORD IN

NOT KINKED OR STORED IN A TWISTED MANNER, AND THAT YOU REGULARLY CHECK ITS CONDITION.



THE USE OF ANY ACCESSORY ATTACHMENTS NOT RECOMMENDED BY COOPERS OF STORTFORD MAY

CAUSE INJURIES AND INVALIDATE ANY WARRANTY YOU MAY HAVE.



DO NOT LET CORD HANG OVER THE EDGE OF A TABLE OR COUNTER, OR TOUCH HOT SURFACES.



DO NOT PLACE ON OR NEAR HEAT SOURCES, AND USE ON A LEVEL, STABLE SURFACE.



DO NOT COVER THE ITEM IN ANY WAY WHEN IN USE AS THIS MAY CAUSE OVERHEATING AND/OR

MUFFLED SOUND.



DO NOT USE THIS APPLIANCE FOR ANY OTHER USE THAN THE INTENDED USE IT IS DESIGNED FOR.



ENSURE THERE IS SUFFICIENT DISTANCE BETWEEN THIS APPLAINCE AND OTHER ITEMS ON THE WORK

SURFACE OR WORK STATION, OR SUFFICIENT DISTANCE BETWEEN THE APPLIANCE AND THE CONFINES OF

THE AREA IN WHICH IT IS SITUATED. WE RECOMMEND A MINIMUM CLEARANCE AROUND ALL FACES OF

AT LEAST 10CM.



BEFORE USE, CHECK THOROUGHLY FOR ANY DEFECTS AND DO NOT USE IF DEFECTS ARE FOUND. TAKE

CARE NOT TO DROP THE APPLIANCE AS HEAVY IMPACTS MAY CAUSE INTERNAL DAMAGE.



IF HEADPHONES ARE USED THEN PLEASE ADJUST THE RADIO VOLUME CONTROL. DO NOT LISTEN AT HIGH

VOLUME LEVELS FOR LONG PERIODS TO AVOID POSSIBLE HEARING DAMAGE.

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

PRODUCT OVERVIEW

SEARCH CONTROL

2. POWER BUTTON

3. MODE BUTTON

4. SELECT BUTTON

5. PRESET BUTTON

6. LCD DISPLAY

7. MENU BUTTON

8. INFO BUTTON

9. ALARM/SNOOZE BUTTON

10. SLEEP BUTTON

11. VOLUME CONTROL

12. SPEAKER

13. BATTERY DOOR

14. ROD ANTENNA

15. HEADPHONE JACK

16. DC INPUT SOCKET

17. AC/DC ADAPTER

SWITCHING YOUR RADIO ON FOR THE FIRST TIME

AC OPERATION

1. Insert the DC power plug of AC/DC adaptor to the DC input socket located at the rear of the radio.

2. Plug the AC/DC Adaptor to the AC mains outlet and switch ON.

3. Press the power button to turn the radio on.

Remarks: Only use with the mains adaptor with 6v dc output voltage as provided to avoid electrical damage to the radio or household mains supply.

DC (BATTERY) OPERATION

1. Ensure the AC/DC adaptor is disconnected from the radio and AC mains.

2. Install the batteries (4×1.5V UM3/AA battery) into the battery compartment (not provided).

3. Press the power button to turn the radio on.

Remarks: To obtain the best performance in DC operation, the use of alkaline batteries is highly recommended.

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

MENUS

Press MENU button to enter into the “MENU”. Rotate SEARCH Control to navigate the desired option, then press

SELECT button to confirm.

SETTING THE CLOCK

The clock in this radio is equipped to receive a DAB radio frequency time signal. After the unit has been turned on, it will automatically tune into a DAB radio station and update the clock. It may be necessary to wait for 1-2 minutes to allow the unit to receive the time signal. If the area will only receive an FM signal it will be necessary to manually set the clock.

Set the clock in STANDBY mode

Insert the AC/DC adaptor into the power socket at the rear of the radio. Plug the adaptor into the mains supply socket.

The display backlight will illuminate for a few seconds, a welcome message (F.1) will appear in the display briefly and the clock will be displayed “00:00:00 Time is not set” will be displayed.

In standby mode, press the ALARM/SNOOZE button, display will show “Time is not set” then the hour digits will flash in the display, rotate the SEARCH control to set the correct hour, then press the SELECT button to confirm.

The minute digits will now flash, rotate the SEARCH control to set the correct minute.

Later you will enter to “set date 1-1-2014”. Rotate the SEARCH control to set date and press SELECT button to confirm again.

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

Set the clock in working mode

1. Connect the radio to AC mains (via AC/DC adaptor), then press power button to turn the radio on.

2. Press MENU button, rotate the SEARCH control until the display show “System”, then press the SELECT button to confirm.

3. Continue to rotate the SEARCH control until the display shows “Time” and then press the SELECT button to

Confirm, the LED display will show “<Set Time /Date>” press the SELECT button again to confirm.

4. The hour digits will flash in the display, rotate the SEARCH control to set the correct hour, then press the

SELECT button to confirm.

5. The minute digits will now flash, rotate the SEARCH control to set the correct minute.

6. Later you will enter to “set date 1-1-2014”. Rotate the SEARCH control to set date and press SELECT button

to confirm again.

BASIC OPERATION - GETTING STARTED

1. Press the power button to turn the unit on, it will automatically enter into the DAB mode and perform auto scan function. During the scan the display will show “Scanning…” together with a slide bar that indicates the progress of the scan and the amount of stations that have been found so far.(F.1) (F.2).

2. Once the scan has finished, the radio will select the first alphanumerically found station. You can now

rotate the SEARCH control to explore the found stations followed by pressing the SELECT button to select

listening to the stations.

Note: If there is no stations found after auto scan, the radio will display "Full Scan", you can now rotate the

SEARCH control to select “Manual tune” or “Full scan” for stations, and press SELECT button to finally

confirm.

DAB Auto Scan

The auto scan will search for the entire DAB Band III channels, After the scan has finished, the first alphanumerically found station will be automatically selected.

1. To activate auto scan, press MENU button, rotate the SEARCH control to enter into the Menu to select “Full scan”, finally press the SELECT button to confirm, the display will show “Scanning…” together with a slide bar that indicates the progress of the scan. (F.3)

2. All the stations that have been found will be stored automatically, to explore the stations that have been found, rotate the SEARCH control and when you find a station that you would like to listen to, press the SELECT button.

DAB Manual tune

1. To select manual tune, press MENU button, rotate the SEARCH control to select “Manual tune”.(F.4) And

press the SELECT button to confirm.

2. Rotate the SEARCH control to move through the DAB channels, the display will show “5A to 13F” and their

associated frequencies. (F.5)

3. When your desired frequency appears in the display, press the SELECT button to listen, the name of the

station group (ensemble/multiplex) will be displayed.

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

Prune

You may remove all unavailable stations on the station list.

1. During DAB mode, press MENU button and then rotate the SEARCH control to select “Prune”. And press the

SELECT button to confirm.

2. Rotate the SEARCH control to select <Yes> to confirm delete. Or select <No> to cancel. Press the

SELECT button to confirm the setting.

DAB display modes

Every time you press the INFO button, the display will cycle through the following display modes:

Signal Strength, Programme Type, Ensemble Name, Channel number/frequency, Signal error, Audio Bit Rate,

Power status (Mains/Battery), Time and Date.

Signal Strength

This shows a slide bar to indicate the signal strength, the stronger the signal, the longer the bar will be from left to right.

Programme Type

This describes the “style” or “genre” of the programme that is being broadcast.

Ensemble Name

The Ensemble/Multiplex is a collection of radio stations that are bundled and transmitted together in a single frequency. There are national and local multiplexes, local ones contain stations that are specific to that area.

Channel number / frequency

This displays the Channel number/frequency of the present station, such as “11C 220.352MHz”.

Signal error

Show the stability and quality of signal reception, the best representation for 0.

Audio Bit Rate

The display will show the digital audio bit rate being received.

Power status

Display the power supply is adaptor or battery. If the power supply is battery, the display will show the battery capacity (21-100). When the battery is less than 20, the display will show battery is low.

Time / Date

This displays the current time and date provided automatically by the broadcaster.

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

FM radio

1. To select FM, press the MODE button, the display will show FM and the frequency.

2. To activate auto search, press SELECT button or rotate and hold the SEARCH control anticlockwise or clockwise until the radio starts to scan the frequency band, the display will show “Scanning …“ (F6) and it will stop automatically once a station has been found.

3. To search manually, rotate the SEARCH control in the desired direction to increment the frequency by

0.05MHz. If reception is still poor adjust the position of the antenna or try moving the radio to another location.

Scan setting

During FM mode, press the MENU button and then rotate the SEARCH control to select “Scan setting” finally press the SELECT button to confirm. Rotate the SEARCH control to select “All stations/Strong stations only”. Press the SELECT button to confirm the setting.

Audio setting

FM is able to search for Stereo or Mono stations.

1. Press the MENU button, then rotate the SEARCH control to select "Audio setting", and press SELECT to confirm.

2. Rotate the SEARCH control to select "Stereo allowed" or "Forced mono", and press SELECT to confirm.

Note:

The radio will automatically switch between stereo and mono mode, but you can override this and switch this function manually which is helpful for poor signal reception.

FM display modes

Every time you press the INFO button, the display will cycle through the following display modes: Radio Text,

Programme Type, Frequency, Audio Type, Power status (Mains/Battery), Time and Date.

Radio Text

This displays the information about the current programme.

Programme Type

This describes the “style” or “genre” of the programme that is being broadcast.

Frequency

This displays the frequency of the present station, such as “87.8MHz”.

Audio Type

This displays if the station being received is in mono or stereo.

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

Power status

Display the power supply is adaptor or battery. If the power supply is battery, the display will show the battery capacity.

Time

This display the current time provided automatically by the broadcaster.

Date

This display the current date provided automatically by the broadcaster.

STORING AND RECALLING STORED STATIONS

This function allows up to 10 stations to be programmed into the memory and stored in both DAB and FM mode.

1. To store a preset, first tune to your desired station, then press and hold the PRESET button for longer than

2 seconds ,the display will show the “Preset Store <#:(Empty)>” (F7).

2. Rotate the SEARCH control to select your desired station preset number.

3. Press the SELECT to confirm your selection, the station now broadcasting has now been stored in the

selected location (F8).

4. To listen to the preset stations, press the PRESET button once and then rotate the SEARCH control to select

the desired preset location. And press the SELECT button to confirm. (F.9) The station name or frequency

and preset location number will be displayed in the lower half of the display. If the preset has not been

allocated ‘Preset Recall #: (Empty)’, “Preset empty” will be shown in the display.

Notes:

If the unit is disconnected from the mains supply for any length of time and the batteries are not installed, the programmed stations will be lost.

SETTING ALARMS (AC OPERATION ONLY)

1. Alarm will only function when the product is on Mains power. Attempting to enter Standby mode when powered only by battery will turn the product off.

2. An active alarm is indicated by its icon in the top line of the display in standby mode.

3. Alarms can be switched on or off in standby mode. However, the alarm parameters can only be set when the product is on.

4. To set or change alarm 1, press ALARM/SNOOZE button once, then press the SELECT button. (F.10)

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

5. To set or change alarm 2, press the ALARM/SNOOZE button twice, then press the SELECT button.

6. To exit alarm setting mode, press the ALARM/SNOOZE button again.

7. The alarm setup prompts you for the following parameters. Select a value for each parameter in rotating the

SEARCH control and press the SELECT button to confirm and move on to the next parameter.

8. Parameters

- On Time – Hours and minutes

- Duration (minutes) - 15/30/45/60/90

If the alarm is not cancelled product returns to standby after this time period.

- Source- Buzzer/DAB/FM

If DAB or FM is chosen as the audio source you will also be prompted to select the last played station or one of the preset station (if set)

- Daily/Once/Weekends/Weekdays

Choose the days on which the alarm is active

Note: if you choose “Once”, you are prompted to enter the required date.

- Volume – Rotate the SEARCH control increase or decrease the volume you desired

This is the volume the alarm will build up to. (Initially the alarm sounds at a low volume and gradually gets louder to the set volume)

- Alarm – Off/ On

- In standby mode, active alarms are indicated by displaying the relevant Alarm 1 and or Alarm 2

icons.

- At the set time, the alarm will sound, quietly at first, then gradually building up to the set volume.

When an alarm sounds.

To turn alarms on or off in standby mode

1. Press the ALARM/SNOOZE button, the display shows the current alarm status. To switch the alarms on or

off.

2. Press the ALARM/SNOOZE button repeatedly to cycle through four states as shown below. (F.11)

3. To choose the display Alarm status, press the SELECT button to confirm.

Note 1:

If you have activated the alarm function and the wake up mode is DAB or FM, make sure that the alarm volume level is set at a sufficient level for you to hear.

Note 2:

If one alarm arrive while the other is in snooze mode, snooze mode will be cancelled.

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

SNOOZE (AC OPERATION ONLY)

1. To temporarily silence a sounding alarm, press the ALARM/SNOOZE button once, you can change the

snooze period by repeatedly pressing the ALARM/SNOOZE button, Snooze periods are 5 or 10

minutes. The radio returns to standby for the set time period with Snooze countdown displayed. When the

countdown reaches 0(zero) the alarm triggered again. (F.12) (F.13)

2. Press the POWER button to fully cancel a sounding alarm and switch the ratio to standby.

SLEEP (AC OPERATION ONLY)

This function allows you to program the unit to switch off by itself after a set period of time.

1. Press the SLEEP button once. You can choose the sleep time:

Sleep Off/10/20/30/60/70/80/90 minutes (F14).

Rotate the SEARCH control to cycle through the options or press the SLEEP button repeatedly, then press the

SELECT button to choose the displayed option.

2 . Or press the MENU button, then rotate the SEARCH control until the display shows ‘System’, and press the

SELECT button to confirm. Rotate the SEARCH control until the display shows “Sleep” then press the SELECT

button to confirm.

3. Rotate the SEARCH control so that you can choose the sleep delay time from: Sleep Off/10/20/30 /60/70/

80/90 minutes and then press the SELECT button to confirm. (F.14).

4. To check the sleep interval remaining, rotate the SEARCH control until the display shows “Sleep’, then press

the SELECT button to check.

5. To cancel the sleep timer, press the MENU button, then rotate the SEARCH control until the display shows

‘System’, and press the SELECT button to confirm. Rotate the SEARCH control until the display shows

“Sleep”, then press the SELECT button to confirm. Rotate the SEARCH button to select “Sleep Off”, then

press SELECT button to confirm.

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

USING HEADPHONES (not included)

A stereo headphone jack has been provided so that the set can be used without disturbing others. Plug in the headphones at the point marked ‘ ’ and adjust the listening volume to your chosen level. Excessive sound pressure from earphones and headphones can cause hearing loss. The speakers will not operate when earphones are fitted.

RESET

1. If moving the radio to another location in the country the pre-tuned and stored DAB stations may no longer

be available and it will be necessary to reset the radio back to the factory settings.

2. With the unit switched on, press the MENU button and rotate the SEARCH control until the display shows

‘ System’ and press the SELECT button and continue rotate the SEARCH control until the display shows

“Factory Reset <No> Yes’ and Rotate the SEARCH control “<Yes>” and press the SELECT button. (F.15), (F.16)

3. The radio will display “Restarting….” and will then go into standby mode.

Note: All stored programmed stations will be lost during reset.

BACKLIGHT

The product display has a backlight with three brightness setting - Low/Medium/High

1. With the unit switched on, press the MENU button, and then rotate the SEARCH control until the display

shows “System”. Press the SELECT button to confirm.

2. Rotate the SEARCH control until the display shows “Backlight”, and press the SELECT button to confirm.

3. Rotate the SEARCH control cycle through “Low/Medium/High” and press the SELECT button to confirm the

setting.

DIMENSION & WEIGHT

Unit dimension:

Weight: approx. 230 (L) x 110 (D) x 140 (H) mm approx. 0.9 kg

Digital Radio & Alarm Clock

10477

Instructions for Use

Please read and retain these instructions for future reference v001: 12/08/16

WARNING

• CHECK THE APPLIANCE AND POWER CABLE CAREFULLY FOR DAMAGE BEFORE EACH USE.

• KEEP THE APPLIANCE AWAY FROM CHILDREN.

• BEFORE CONNECTING THE APPLIANCE, CHECK IF THE VOLTAGE INDICATED ON THE BOTTOM OF THE

APPLIANCE AND AC MAINS ADAPTOR IS IN ACCORDANCE WITH THE MAINS VOLTAGE IN YOUR HOME.

• THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND PERSONS WITH

REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF

THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE

WAY AND UNDERSTAND THE HAZARDS INVOLVED. CHILDREN SHALL NOT PLAY WITH THE APPLIANCE.

CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY CHILDREN WITHOUT SUPERVISION.

• SOME PARTS OF THIS PRODUCT CAN BECOME VERY HOT AND CAUSE BURNS. PARTICULAR ATTENTION

HAS TO BE GIVEN WHERE CHILDREN AND VULNERABLE PEOPLE ARE PRESENT.

• CHILDREN OF LESS THAN 3 YEARS SHOULD BE KEPT AWAY UNLESS CONTINUOUSLY SUPERVISED.

• KEEP ITEM AT LEAST 1M AWAY FROM COMBUSTIBLE MATERIAL SUCH AS FURNITURE, CUSHIONS,

BEDDING, PAPER, CLOTHES, CURTAINS ETC.

• DO NOT USE IF THE POWER CORD OR PLUG IS DAMAGED. TO BE REPAIRED BY A QUALIFIED ELECTRICIAN

OR TO BE REPLACED BY THE MANUFACTURER, SERVICE AGENT OR SIMILARLY QUALIFIED PERSON, IN

ORDER TO AVOID A HAZARD.

CARE AND CLEANING INSTRUCTIONS



Always switch off and unplug before cleaning.



Do NOT immerse in water. Risk of electric shock.



Do NOT use abrasive cleaners or sharp utensils to clean this appliance.



Wipe surfaces with a soft dry cloth.



Store the unit in a cool, dry place.

BATTERIES (not included)

• Keep batteries away from children and pets.

• Do not mix used and new batteries.

• Remove the batteries if left for long periods.

• Never dispose of batteries in a fire.

• Battery disposal, spent or expired batteries must be properly disposed of and recycled in compliance with local regulations. For detailed information, contact your local authority.

• Follow the battery manufacturer’s safety, usage, and disposal instructions.

DISPOSAL

• Dispose of all packaging, paper, cartons and plastic, plastic bags in accordance with your local recycling regulations.

• At the end of the product’s lifespan please dispose of it at an authorised household WEEE waste recycling centre.

Hello! I am an AI chatbot specifically trained to assist you with the Coopers 10477 Operating instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!