ABB SM500F User Manual
Advertisement
Advertisement
User Guide
IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
ABB
The Company
EN ISO 9001:2000
We are an established world force in the design and manufacture of instrumentation for industrial process control, flow measurement, gas and liquid analysis and environmental applications.
As a part of ABB, a world leader in process automation technology, we offer customers application expertise, service and support worldwide.
We are committed to teamwork, high quality manufacturing, advanced technology and unrivalled service and support.
The quality, accuracy and performance of the Company's products result from over 100 years experience, combined with a continuous program of innovative design and development to incorporate the latest technology.
The UKAS Calibration Laboratory No. 0255 is just one of the ten flow calibration plants operated by the Company and is indicative of our dedication to quality and accuracy.
Cert. No. Q 05907
EN 29001 (ISO 9001)
Lenno, Italy – Cert. No. 9/90A
Stonehouse, U.K.
0255
Electrical Safety
This equipment complies with the requirements of CEI/IEC 61010-1:2001-2 'Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use'. If the equipment is used in a manner NOT specified by the Company, the protection provided by the equipment may be impaired.
Symbols
One or more of the following symbols may appear on the equipment labelling:
Warning – Refer to the manual for instructions Direct current supply only
Caution – Risk of electric shock
Protective earth (ground) terminal
Earth (ground) terminal
Alternating current supply only
Both direct and alternating current supply
The equipment is protected through double insulation
Information in this manual is intended only to assist our customers in the efficient operation of our equipment. Use of this manual for any other purpose is specifically prohibited and its contents are not to be reproduced in full or part without prior approval of the Technical Publications Department.
Health and Safety
To ensure that our products are safe and without risk to health, the following points must be noted:
1.
The relevant sections of these instructions must be read carefully before proceeding.
2.
Warning labels on containers and packages must be observed.
3.
Installation, operation, maintenance and servicing must only be carried out by suitably trained personnel and in accordance with the information given.
4.
Normal safety precautions must be taken to avoid the possibility of an accident occurring when operating in conditions of high pressure and/or temperature.
5.
Chemicals must be stored away from heat, protected from temperature extremes and powders kept dry. Normal safe handling procedures must be used.
6.
When disposing of chemicals ensure that no two chemicals are mixed.
Safety advice concerning the use of the equipment described in this manual or any relevant hazard data sheets (where applicable) may be obtained from the Company address on the back cover, together with servicing and spares information.
Field Mountable Videographic Recorder
SM500F Contents
Contents
1 Introduction ...................................................................................................................................... 3
1.1
Functional Overview ................................................................................................................. 3
2 Installation ........................................................................................................................................ 5
2.1
Siting ....................................................................................................................................... 6
2.2
Mounting ................................................................................................................................. 8
2.2.1 Panel-Mounting ............................................................................................................. 9
2.2.2 Wall-Mounting ............................................................................................................. 10
2.2.3 Pipe-Mounting (Optional) ............................................................................................. 11
2.3
Electrical Connections ........................................................................................................... 12
2.3.1 Cable Entries ................................................................................................................ 13
2.3.2 Connections ................................................................................................................. 15
2.4
Analog/Digital Inputs .............................................................................................................. 16
2.4.1 Thermocouple ............................................................................................................. 16
2.4.2 Resistance Thermometer (RTD) .................................................................................... 16
2.5
Power Supply Connections .................................................................................................... 17
2.6
Transmitter Power Supply Module ......................................................................................... 18
2.7
Relays ................................................................................................................................... 18
3 On-Line Help .................................................................................................................................. 19
4 Operation ....................................................................................................................................... 20
4.1
Powering up the Instrument ................................................................................................... 20
4.2
Operator Keys and Door Features ......................................................................................... 20
4.3
Operator Display Overview...................................................................................................... 21
5 Logging .......................................................................................................................................... 22
5.1
Logging Access ..................................................................................................................... 22
5.1.1 Password Entry ........................................................................................................... 24
6 Configuration ................................................................................................................................. 25
6.1
Introduction ........................................................................................................................... 25
6.2
Configuration Level Security ................................................................................................... 25
6.3
Configuration Level Access..................................................................................................... 26
6.4
Overview of Configuration ....................................................................................................... 29
6.5
Making Changes to Parameters.............................................................................................. 30
7 Specification .................................................................................................................................. 34
IM/SM500F Issue 10.1
1
Field Mountable Videographic Recorder
SM500F Contents
Appendix A – Signal Sources ............................................................................................................. 45
Appendix B – ModbusTCP Guide ...................................................................................................... 47
B.1
Introduction ............................................................................................................................ 47
B.2
Modbus Commands Supported ............................................................................................. 47
B.3
Modbus Exception Responses ............................................................................................... 47
B.4
Operating Mode Modbus Coils ............................................................................................... 48
B.5
Operating Mode ModbusTCP Registers ................................................................................. 52
B.6
Communications – Analog and Digital Inputs .......................................................................... 54
Appendix C – Storage Capacity ......................................................................................................... 57
C.1
Internal Storage Capacity ....................................................................................................... 57
C.2
External Storage Capacity ...................................................................................................... 57
Appendix D – Units ............................................................................................................................. 58
Index ..................................................................................................................................................... 60
Notes ................................................................................................................................................... 62
2 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 1 Introduction
1 Introduction
1.1 Functional Overview – Fig. 1.1
The instrument features the following functionality:
8 Software Recording Channels as standard, divided into 2 Process Groups, each with 4 Software
Recording Channels.
4 Alarms and 2 Totalizers are assigned to each Recording Channel.
Signal sources derived from universal analog inputs, Modbus communications, digital inputs or internal analog and digital signals.
Any source can be assigned to any recording channel.
Data from assigned sources can be displayed in:
– Vertical or Horizontal Chart view format
– Indicator view format with optional integrated Bargraph view
Three instrument logs record alarm events, totalizer values and system/configuration changes.
Modbus TCP – communicate with Modbus master and slave devices over an ethernet LAN.
Screen Capture facility – saves an image of the operator views to external archive media providing external archive media with sufficient free space is inserted in the instrument. It is not necessary for
Logging to be 'online'.
Internal flash memory for the storage of recorded data.
The ability to archive data to external archive media in either text (*.csv) or binary formats.
Integrated web server and file transfer protocol (ftp) support for remote monitoring and data acquisition.
IM/SM500F Issue 10.1
3
Field Mountable Videographic Recorder
SM500F 1 Introduction
Signal Sources
see Appendix A
Note.
Signal sources can be assigned to any recording channel in either process group.
Analog Sources
A1
B1
C1
D1
Error States
Communications
Analog Sources
1
2
3
A1
B1
C1
D1
24
Communications
Digital Sources
1
2
3
24
Digital Sources
Recorded Data
Recording Channels 1.1 to 1.4
(Process Group 1)
Recording Channels 2.1 to 2.4
(Process Group 2)
Instrument Logs
Configuration Data
Process Group 1
1.1
1.2
Recording Channels
1.1 to 1.4
1.3
1.4
Two process groups as standard provide 8 software recording channels, irrespective of the number of external inputs.
Process Group 2
2.1
2.2
2.3
2.4
Chart View
Recording
Channels
2.1 to 2.4
Instrument Logs
Alarm/Event Log
Totalizer Log
Chart View
Records all alarm transistions and operator messages
Records all totalizer activity*
Indicator View
Alarm Event Log
Audit Log
Records all system activity
* If totalizer option enabled
Configuration Data
Configuration
Data
Stores all instrument configuration, calibration and user preferences
Audit Log
Indicator View
Totalizer Log
Views provide a window on the stored data.
Archive Data
Files stored in instrument's on-board flash memory.
Newest data overwrites oldest.
Archive Media
Data saved to archive storage media
Fig. 1.1 Functional Overview
4 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 2 Installation
2 Installation
EC Directive 89/336/EEC
In order to meet the requirements of EC Directive 89/336/EEC for EMC regulations, this product must not be used in a non-industrial environment.
End of Life Disposal
The instrument contains a small lithium battery that must be removed and disposed of responsibly in accordance with local environmental regulations.
The remainder of the instrument does not contain any substance that causes undue harm to the environment and must be disposed of in accordance with the Directive on Waste Electrical and
Electronic Equipment (WEEE). It must not be disposed of in Municipal Waste Collection.
Cleaning
The complete instrument can be hosed down if it has been installed to IP66/NEMA 4X standards, i.e.
cable glands are correctly fitted and all unused cable entry holes are blanked off – see section 2.3.1, page 13. Warm water and a mild detergent can be used.
IM/SM500F Issue 10.1
5
Field Mountable Videographic Recorder
SM500F
2.1 Siting – Figs 2.1 and 2.2
Keep distance to a minimum
Sensors
A Close to Sensors
2 Installation
B At Eye-level Location
Fig. 2.1 General Siting Requirements
C Avoid Vibration
6 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
50°C
(122°F)
Max.
-10 °C
(14°F)
Min.
A Within Temperature Limits
2 Installation
0 to 95% RH
B Within Humidity Limits
IP66 / NEMA 4X +
C Environmental Protection Standards
Fig. 2.2 Environmental Requirements
D Use Screened Cable
Warning.
Locate the instrument in a position where its temperature and humidity specification will not be exceeded, and ensure that it is suitably protected from direct sunlight, rain, snow and hail.
Select a location away from strong electrical and magnetic fields. If this is not possible, particularly in applications where mobile communications equipment is expected to be used, screened cables within flexible, earthed metal conduit must be used.
IM/SM500F Issue 10.1
7
Field Mountable Videographic Recorder
SM500F
2.2 Mounting
Dimensions in mm (in.)
Gasket 7 (0.3) 48 (1.9)
2 Installation
144
(5.7)
144 (5.7)
36 (1.4)
21 (0.8)
3 Pitches of
34.2 (1.35) Ø 22.2
(0.87)
Ø 30
(1.2)
138
(5.43
+1.0
0.0
+0.04
0.0
)
30
(1.2)
24 (0.9)
3 (0.12)
Gasket
Panel Cut-out
138
(5.43
+1.0
0.0
+0.04
0.0
)
30
(1.2)
Fig. 2.3 Mounting Dimensions
8 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
2.2.1 Panel-Mounting – Fig. 2.4
2 Installation
1
Clamp
Bracket
Bracket
Securing
Screw
4
Clamping Screw
2
3
Left-hand panel clamp assembly only shown.
Right-hand assembly omitted for clarity
5
Fig. 2.4 Installing the Instrument – Panel-Mounting
Note.
If removal of knockouts is required, refer to Section 2.3.1 on page 13.
Referring to Fig. 2.4, secure the instrument in a panel as follows: a Cut the correct sized hole in the panel – see Fig. 2.3 on page 8.
b Insert the instrument into the panel cut-out.
c Screw one clamping screw into the left-hand bracket until 10 to 15mm of the thread protrudes from the other side of the bracket and position one clamp over the end of the thread.
d Holding the assembly together, position the bracket into the left-hand recess on the rear of the instrument case and secure with the bracket securing screw. Ensure that the plastic washer remains in the position fitted.
Repeat instructions 3 and 4 for the right-hand panel clamp assembly.
e Tighten the clamping screws evenly and securely by hand.
Note.
This is critical in order to ensure proper compression of the panel seal and achieve the
IP66/NEMA 4X hosedown rating.
IM/SM500F Issue 10.1
9
Field Mountable Videographic Recorder
SM500F
2.2.2 Wall-Mounting – Fig. 2.5
Dimensions in mm (in.)
2 Installation
152 (5.98)
62
(2.44)
2
1
Left-hand bracket only shown.
Right-hand bracket omitted for clarity
3
Fig. 2.5 Installing the Instrument – Wall-Mounting
Note.
If removal of knockouts is required, refer to Section 2.3.1 on page 13.
Referring to Fig. 2.5, secure the instrument to a wall as follows: a Position the left- and right-hand mounting brackets into the recesses on the rear of the instrument as shown and secure with the bracket securing screws. Ensure the plastic washers remain in the positions fitted.
b Mark fixing centers and drill suitable holes in the wall.
c Secure the instrument to the wall using 2 screws in each mounting bracket.
10 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
2.2.3 Pipe-Mounting (Optional) – Fig. 2.6
2
Vertical pipe
Horizontal pipe
2
1
3
2 Installation
4
Fig. 2.6 Installing the Instrument – Pipe-Mounting (Optional)
Note.
If removal of knockouts is required, refer to Section 2.3.1 on page 13.
Referring to Fig. 2.6, secure the instrument to a pipe as follows: a Fit two M6 x 50mm long hexagon-head screws through one clamp plate as shown.
b Using the appropriate holes to suit vertical or horizontal pipe, secure the clamp plate to the pipe-mounting bracket using the two M6 x 8mm long hexagon-head screws and two of the spring lock washers.
c Position the pipe mounting bracket into the recesses on the rear of the instrument as shown and secure with the two bracket securing screws. Ensure the plastic washers remain in the positions fitted.
d Secure the instrument to the pipe using the remaining clamp plate, spring lock washers and nuts.
IM/SM500F Issue 10.1
11
Field Mountable Videographic Recorder
SM500F 2 Installation
2.3 Electrical Connections
Warning.
The instrument is not fitted with a switch therefore a disconnecting device such as a switch or circuit breaker conforming to local safety standards must be fitted to the final installation. It must be fitted in close proximity to the instrument within easy reach of the operator and must be marked clearly as the disconnection device for the instrument. A fuse must be fitted in accordance with Fig. 2.10.
Remove all power from supply, relay and any powered control circuits and high common mode voltages before accessing or making any connections.
Use cable appropriate for the load currents: 3-core cable rated 3 A and 90 °C (194 °F) minimum, that conform to either IEC 60227 or IEC 60245. The terminals accept cables from 0.8 to 2.5 mm 2
(18 to 14 AWG).
The instrument conforms to Installation Category II of IEC 61010.
All connections to secondary circuits must have basic insulation.
After installation, there must be no access to live parts, for example, terminals.
Terminals for external circuits are for use only with equipment with no accessible live parts.
If the instrument is used in a manner not specified by the Company, the protection provided by the equipment may be impaired.
All equipment connected to the instrument's terminals must comply with local safety standards
(IEC 60950, EN601010-1).
Note.
Always route signal leads and power cables separately, preferably in earthed (grounded) metal conduit.
Use screened cable for signal inputs and relay connections.
Replacement of the internal battery (type Varta CR2025 3V lithium cell) must be carried out by an approved technician only.
12 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 2 Installation
2.3.1 Cable Entries – Fig. 2.7
Referring to Fig. 2.7 on page 14: a Route cables through the four holes provided on the bottom of the case.
b Knockouts are provided on the rear of the instrument case as an alternative means of cable entry. To remove a knockout, place the back of the instrument on a firm, flat surface, open the door and inner cover (see Fig. 6.3 on page 28) and carefully remove the knockout by placing the blade of a small, flat-bladed screwdriver into the knockout groove and tapping the screwdriver smartly with a hammer.
c Use the indicated cable entry hole or knockout if the optional Ethernet module is fitted. d Connect the Ethernet cable, ensuring that if optional input modules are fitted in positions B and C, the cable is routed between their terminal blocks as shown.
e Connect cable screens only to the terminals indicated.
Note.
For wall- or pipe-mounting to IP66/NEMA4X standard, fit suitable cable glands. Blank off any unused holes with the blanking plugs and retaining clips supplied with the instrument.
Optional cable glands are available and are suitable for use with cables Ø 5 to 9mm (0.20 to
0.35 in.). The alternative 2-hole cable gland inserts are suitable for use with cables Ø 5mm
(0.20 in.). The Ethernet cable gland is suitable for use with cable Ø 4.8 to 6.3mm (0.19 to
0.25 in.).
IM/SM500F Issue 10.1
13
Field Mountable Videographic Recorder
SM500F
1
2
3
2 Installation
5
Fig. 2.7 Cable Knockouts, Ethernet Cable Routing and Cable Screening Connections
4
14 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
2.3.2 Connections – Fig. 2.8
F
2 Installation
A B C D
E G
F
Ethernet
THC/mV/V
Digital Input
—
A
B
C
D
Analog/
Digital
Input
1 4
Current
—
*
3 4
D
24V
Tx PSU
R/RTD 3
2 3 4
R/RTD 4
— —
D
Dual
Relay
NO
LK1 LK2
Relay 1 Relay 2
NC
Relay 1
C NO/NC
Relay 2
C NO/NC
NO
LK1
E
Relay
NC
Relay
C NO/NC
G
Power
Supply
10 to 36V DC or
85 to 265V AC
—
1 2 3 4
1 2 3 4 1 2 3 4 1 2
1 2 3
3 4
4
1 2 3 4
1 2 1 2 3
1 2 3
1 2
A B C D E G
* In the powered-down condition the current input is open circuit. In order to maintain a current loop when the unit is powered down, fit a zener diode (BZX79 — B/C2V4) to the input as shown.
Fig. 2.8 Electrical Connections
Note.
Power supply terminal screws must be tightened to a torque of 0.8 Nm (7 lbf.in). All other terminal screws must be tightened to a torque of 0.5 Nm (4.5 lbf.in).
IM/SM500F Issue 10.1
15
Field Mountable Videographic Recorder
SM500F 2 Installation
2.4 Analog/Digital Inputs
2.4.1 Thermocouple – Fig. 2.9
Use the correct compensating cable between the thermocouple and the terminals – see Table 2.1 on page 17.
Automatic cold junction compensation (ACJC) is incorporated but an independent cold (reference) junction may be used.
2.4.2 Resistance Thermometer (RTD) – Fig. 2.9
On applications requiring long leads it is preferable to use a 3-lead resistance thermometer.
If 2-lead resistance thermometers are used, each input must be calibrated to take account of the lead resistance.
1 2 3 4 1 2 3 4 1 2 3 4
+ —
—
Voltage Current
—
*
Thermocouple
1 2 3 4 1 2 3 4 1 2 3 4
—
3-lead RTD
Each lead must be of equal resistance and less than 10 Ω
4-lead RTD
* In the powered-down condition the current input is open circuit. In order to maintain a current loop when the unit is powered down, fit a zener diode
(BZX79 — B/C2V4) to the input as shown.
Logic state inactive
Logic state active
Digital Input
(Volt free or 24V)
Fig. 2.9 Analog/Digital Input Connections
Note.
Analog/digital input terminal screws must be tightened to a torque of 0.5 Nm (4.5 lbf.in).
16 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 2 Installation
Thermocouple Type
Ni-Cr/Ni-Al (K)
Ni-Cr/Cu-Ni (E)
Nicrisil/Nisil (N)
+
BS1843
– Case
Compensating Cable
ANSI MC 96.1
+ – Case
Brown Blue Red Yellow Red Yellow
– –
Orange Blue Orange Orange Red Orange
+
Red
DIN 43714
Green Green
–
–
– Case
BS4937 Part No.30
+
Green White
Violet
Pink
–
White
White
Case
Green *
Violet *
Pink *
Pt/Pt-Rh (R and S)
Pt-Rh/Pt-Rh (B)
Cu/Cu-Ni (T)
Fe/Con (J)
Fe/Con (DIN 43710)
White Blue Green
–
White Blue Blue
Yellow Blue Black White Red Black
–
Black Red Green
–
Blue Red Blue
–
Red White White Orange White Orange *
– Grey White Grey *
Red Brown Brown Brown White Brown *
Red Blue Blue Black White Black *
* Case Blue for intrinsically safe circuits
DIN 43710
–
Blue/red Blue Blue
Table 2.1 Thermocouple Compensating Cable
2.5 Power Supply Connections – Fig. 2.10
Line
Neutral
Fuse,
315 mA, Type T
L
N 85 V min. to 265 V max. 50/60 Hz
Warning.
Use Fuse Rating 315 mA (max.) Type T
A AC Supply
+
Fuse,
1.5 A, Type
T
+
10 V min. to 36 V max.DC
Warning.
Use Fuse Rating 1.5 A (max.) Type T
B DC Supply
Fig. 2.10 Power Supply Connections
Note.
Power supply terminal screws must be tightened to a torque of 0.8 Nm (7 lbf.in).
IM/SM500F Issue 10.1
17
Field Mountable Videographic Recorder
SM500F 2 Installation
2.6 Transmitter Power Supply Module – Fig. 2.11
One transmitter power supply module can be fitted in position D to provide a nominal 24V supply capable of driving two, 2-wire transmitters.
+
2-wire Transmitter Power Supply
(24V DC, 22mA max.)
+
Tx
1 2 3 4
Analog Input
Fig. 2.11 Transmitter Power Supply Module
Note.
Analog input terminal screws must be tightened to a torque of 0.5 Nm (4.5 lbf.in).
2.7 Relays
One relay is provided as standard (position E). An additional relay module can be fitted in position D to provide two additional relays.
The maximum individual relay current is 5A.
Relay contacts are fitted with arc suppression components as standard.
Set the polarity using the relay links provided on the instrument's motherboard (for the standard relay) and the relay module board (for the optional additional relays) – see Fig. 2.8 on page 15.
18 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
3 On-Line Help
3 On-Line Help
1
2
4
3
Fig. 3.1 On-Line Help Overview
The instrument is equipped with a context-sensitive, on-line help facility that can be accessed from any operator, logging or configuration view. To navigate the on-line help, refer to Fig. 3.1 and: a Select 'Help' from the menu and press the key. The help index opens automatically at the help page relevant to the view from which help was selected – in this instance, the alarm configuration view.
b Press the and keys to move the selection up and down through the index. Press the key to view the selected help file and use the and keys to scroll through it.
c Highlight a section icon ( ). If it changes to the icon, there is a help file ( ) directly associated with selected section – press the key to open it.
d If the section icon remains closed, the section it represents contains sub-sections and files. Press the
key to open the section and reveal the sub-sections. Repeat the process for sub-sections.
Press the key to close a sub-section or section.
To exit the on-line help, press the key repeatedly to return to the screen from where help was first selected.
IM/SM500F Issue 10.1
19
Field Mountable Videographic Recorder
SM500F 4 Operation
4 Operation
4.1 Powering up the Instrument
When power is first applied to the instrument, its processor carries out a number of self-tests and displays the start-up screen.
At the end of the start-up sequence, the instrument displays the Operator View that was being displayed when the instrument was powered down.
4.2 Operator Keys and Door Features – Fig. 4.1
The instrument is operated via the Operator Keys located below the screen.
1
2
3
7
6
5
4
Fig. 4.1 Operator Keys and Door Features
Referring to Fig. 4.1, operator keys and door features are located as follows: a Menu Key – Displays or hides the context-sensitive operator menu associated with each view.
Also cancels the menu without making a change or returns to the previous menu level.
b Group Key – Selects a different process group or
Left Key – Scroll left.
c d
/ Up/Down Keys
View Key
– Highlights menu items and scrolls through previously recorded data.
– Selects a different process view or log or
Right Key – Scroll right.
e Enter Key – Selects the highlighted menu item. If 'Screen Capture' is set to 'Enabled' during configuration and external archive media is inserted in the instrument, the operator can save a snapshot of any operator view to the external media if pressed when an operator menu is not displayed.
f Door Release .
g Door Lock (optional).
20 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
4.3 Operator Display Overview – Fig. 4.2
Process Group 1
(Recording Channels 1.1 to 1.4)
Process Group 2
(Recording Channels 2.1 to 2.4)
4 Operation
Fig. 4.2 Overview of Operator Displays
Note.
Only process groups and views that are enabled are displayed.
IM/SM500F Issue 10.1
21
Field Mountable Videographic Recorder
SM500F 5 Logging
5 Logging
5.1 Logging Access
Access to Logging is controlled by the instrument's Security System.
If 'Security System' is set to 'Basic' and 'Logging Security' is set to 'Off', access to the Logging facility is unrestricted.
If 'Security System' is set to 'Basic' and 'Logging Security' is set to 'On', access to the Logging facility is protected by a single password for all users. Refer to Fig. 5.1 to access Logging.
If 'Security System' is set to 'Advanced' and 'Logging Security' is set to 'On', access to the Logging facility is protected by a unique password for each authorized user. Refer to Fig. 5.2 on page 23 to access Logging.
Logging Security
Not Enabled
Logging Security Enabled
Invalid Password
Entered
Valid Password
Entered
Fig. 5.1 Accessing Logging – Basic Security
22 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 5 Logging
Logging
Security
Enabled
Logging Security
Not Enabled
Invalid Password
Entered
(see Note below)
Enter Password
(see section 5.1.1, page 24)
Valid Password
Entered
Fig. 5.2 Accessing Logging – Advanced Security
Note.
If an incorrect password is entered the display returns to the Operating view. However, if the maximum number of consecutive incorrect password entries is exceeded, the user's access privileges are removed and the following message is displayed:
If this occurs, access privileges can be reinstated only by the system administrator (User 1). If the system administrator's access privileges have been removed, the security system must be disabled using the configuration security switch to gain access to the configuration.
IM/SM500F Issue 10.1
23
Field Mountable Videographic Recorder
SM500F
5.1.1 Password Entry
5 Logging
Enter password
1.
Select the required character using the , , and keys.
2.
Add the selected character to the password string using the key.
Note.
For security, all characters are displayed as '
'
3.
Repeat 1 and 2 until all characters have been entered.
4.
Highlight the 'OK' button using the , , and keys and press .
Change password
1.
Select 'Change Password' using the , , and keys and press .
2.
Highlight the Edit Button ( ) using the and keys and press to display the character entry box.
3.
Enter the old password using the , , and keys.
Highlight the 'OK' button and press
4.
Enter the new password using the same procedure as for the old password.
5.
Enter the new password again to confirm it.
6.
Highlight the 'OK' button and press .
Password change successful.
Note.
If the key is pressed at any stage or 'OK' is selected before the new password is confirmed, the password change operation is cancelled and the following message is displayed:
24
Password Expired
Passwords can be configured to expire at pre-determined intervals. If a password is time expired, this screen is displayed automatically. Enter a new password as described above.
IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 6 Configuration
6 Configuration
6.1 Introduction
This section describes how to access the instrument's configuration level and make changes to the parameters using the operator keys.
6.2 Configuration Level Security – Table 6.1
Two methods of configuration access protection are available:
1.
Password protection (Factory Default).
The Configuration level cannot be accessed until the correct password has been entered – see
Figs. 6.1 and 6.2 on pages 26 and 27 respectively.
2.
Internal switch protection .
The Configuration level cannot be accessed until the internal switch set to the 'Configuration Level
Not Protected' position – see Fig. 6.3 on page 28.
Internal Security Switch Setting
(see Fig. 6.3)
Configuration Level Protected
(Factory Default)
Configuration Level Not Protected
Table 6.1 Configuration Security Modes
' Configuration security' Parameter Setting
'Password protected'
(Factory Default)
'Switch protected'
(Alternative)
Password Access
Free Access
No Access
Free Access
The instrument can be configured for one of two levels of password protection:
Basic Security:
Up to 4 users
Each user is assigned a unique 4-digit security code for Configuration level access
Optional security code protection of access to the logging facility
Advanced Security:
Up to 12 users
Each user is assigned a unique password of up to 20 characters
Each user is assigned configuration and/or logging access privileges
Each user is assigned one of 3 levels of configuration level access privileges
Configurable password expiry times, password failure limits and minimum password length
Inactive user disabling
IM/SM500F Issue 10.1
25
Field Mountable Videographic Recorder
SM500F 6 Configuration
6.3 Configuration Level Access – Figs. 6.1 to 6.3
To configure an instrument when 'Configuration security' is set to the factory default setting of 'Password protected':
1.
Access the Configuration Level – see Figs. 6.1 and 6.2 on pages 26 and 27 respectively.
2.
Make changes to parameters as detailed in Figs 6.5 and 6.6 (on pages 30 and 31 respectively) and on-line help.
To configure an instrument when 'Configuration security' is set to 'Internal switch protected':
1.
Set the internal security switch to the 'Configuration Level Not Protected' position – see Fig. 6.3.
2.
Access the Configuration Level – see Figs. 6.1 and 6.2 on pages 26 and 27 respectively.
3.
Make changes to parameters as detailed in Figs 6.5 and 6.6 (on pages 30 and 31 respectively) and on-line help.
Configuration Level
Protected
(see section 6.2, page 25)
Displayed only if
'Security system' parameter is set to
'Basic' see on-line help system
Displayed only if
'Security system' parameter is set to
'Advanced' see on-line help system
Invalid Password
Entered
Valid Password
Entered
Configuration Level Unprotected
(see section 6.2, page 25)
Continued in Fig. 6.2 on next page
Fig. 6.1 Accessing the Configuration Level
26 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
From Fig. 6.1
6 Configuration
Edit the current configuration. Changes are not implemented until saved on exit from the
Configuration level
Check this box to stop recording while in the configuration mode.
Use and
to highlight a different selection.
Use to accept the selection.
Cancel and return to the Operator level.
The existing security configuration parameters are retained (i.e. the security configuration remains as currently configured) when a configuration is opened from file or when a new configuration is loaded. Check 'Load security configuration from file' to overwrite the current security configuration with data from the file to be loaded see Note 2 below.
Open a configuration saved previously to internal or external storage (up to 16 configurations can be stored in internal memory) see Note 1 below. Alternatively, open one of the QuickStart templates.
Press to accept the selection.
Press to toggle between internal and external storage.
Press to cancel.
Open a new configuration with the default settings see Note 1 below.
Fig. 6.2 Accessing the Configuration Level
Note.
1.
If 'New Configuration' or 'Open a Configuration' is selected and the modified configuration file is saved later as the current configuration, new internal data files for all enabled recording channels are created and any unarchived data is lost.
2.
The option to load or retain the security configuration applies only to Advanced Security mode and is available only to the System Administrator (User 1). If a new or existing configuration file is opened by a user other than the System Administrator, the instrument's existing security settings are retained.
IM/SM500F Issue 10.1
27
Field Mountable Videographic Recorder
SM500F
2 5
6 Configuration
1
6
3
4
Configuration Level Protected
Configuration Level Not Protected
Fig. 6.3 Setting the Security Switch
Referring to Fig. 6.3, set the internal security switch as follows: a Unlock the instrument door with the key supplied, press the release catch and open the door.
Warning.
Before proceeding to step 2 , isolate the instrument from the power supply.
b Remove the tamper-evident seal (if fitted), release the captive screw securing the inner cover plate and remove the inner cover plate.
c Set the Security switch to the 'Configuration Level Not Protected' position (toward bottom of instrument).
Note.
The Internal Security Switch is used to access the Configuration level when 'Configuration security' is set to 'Switch protected'. Do Not use the switch to access the Configuration level when 'Configuration security' is set to 'Password protected' (default setting) unless the Password has been forgotten. The switch overrides Password protection, enabling free access to the
Configuration level.
d Locate the inner cover plate lugs in the slots in the outer case and close the inner cover plate. e Tighten the inner cover plate retaining screw and fit a tamper-evident seal (if required).
f Close and lock the instrument door and restore the power supply to the instrument.
28 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
6.4 Overview of Configuration – Fig. 6.4
1
6 Configuration
2
3
4
5
6
Fig. 6.4 Overview of Configuration Steps
Referring to Fig. 6.4, configure the instrument as follows: a Select 'Common' from the Configuration menu.
Note.
Only enabled Process Groups (and their associated Channel Options) and enabled software options (i.e. Math and Logic) are visible in the menu.
b Select the parameter required using the and keys.
c Press the key to edit selected parameter.
d Use the and keys to select the next required tab.
e Press the key to display the menu. Select the next item required and activate using the key.
f When all configuration changes are complete, select 'Exit' to save or cancel changes.
IM/SM500F Issue 10.1
29
Field Mountable Videographic Recorder
SM500F
6.5 Making Changes to Parameters – Figs. 6.5 to 6.7
4
1
2
3
5
6 Configuration
6
7
8
Fig. 6.5 Locating Parameter Settings
Referring to Fig. 6.5, parameters are located as follows: a Configuration tab.
b Parameter.
c Parameter value.
d Edit button.
e Sub-menu.
f Higher-level windows remain visible to identify location within the configuration structure.
g Selection list.
h Use the and keys to highlight a selection. Press the key to accept the selection.
Note.
The appropriate data entry box is displayed automatically.
Use the key to open the Configuration menu in order to select a different channel.
30 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 6 Configuration
1
Refer to Note 1 below
1 2 X 4
2
3
4
5
Refer to Note 2 below
59.45
6
Fig. 6.6 Data Entry Dialog Boxes
Note.
1.
Items not selected are indicated by an X in the parameter value window.
2.
Values outside the preset parameter limits or with too many decimal places are highlighted when the OK button is selected.
Referring to Fig. 6.6, use data entry dialog boxes as follows: a Use the and keys to highlight an item and press to select it.
b Parameter limits.
c Use the and keys to highlight the text field and use the and keys to position the cursor to edit text as required.
d Cursor.
e Use the , , and keys and press to highlight a character and press to select it.
f Spacebar.
Note.
Tags with a high percentage of capital letters and wide characters such as 'W' or 'M' may appear truncated in some Operator Views. In such cases, use lower case letters or fewer characters.
IM/SM500F Issue 10.1
31
Field Mountable Videographic Recorder
SM500F
1
5
Configuration change causes the internal recording data files to be recreated
2
Configuration change does not cause the internal recording data files to be recreated
3
4
Fig. 6.7 Exiting Configuration Mode
Referring to Fig. 6.7, exit configuration mode as follows: a Open the menu, select 'Exit' and press .
b To begin using a configuration immediately, select 'Save as Current Configuration'.
6 Configuration
32 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 6 Configuration
Note.
When saving the current configuration to internal storage, it is saved twice, once with the filename 'SM500F.cfg' and again with the filename '<time><date><instrument tag>.cfg'
When saving the current configuration to external storage, it is saved with the filename
'<time><date><>instrument tag>.cfg'. It is also saved automatically to internal storage with the filename 'SM500F.cfg'.
When 'Save Configuration' is selected, the configuration file is saved with the filename
'<time><date><>instrument tag>.cfg' to either selected location, internal or external.
Changes are saved to non-volatile memory only when one of the save options above has been selected. Any powerdown before this results in lost configuration changes.
Selecting 'Cancel' discards unsaved changes and returns the instrument to the Operating level.
New internal data files for enabled recording channels are created if:
– A recording channel source parameter is changed
– The primary and/or secondary sample rates and/or their sources for either process group are changed.
– The input filter type parameter for any channel is changed
– the engineering range parameter for any channel is changed
– A channel tag parameter is changed
– The number of process groups is changed
– A previously disabled channel is enabled
A warning is displayed if a configuration change will result in the creation of new data files.
Select 'Yes' to accept the changes or 'No' to reject them.
Selecting 'Save as Current Configuration' suspends recording for a short time while the new configuration is implemented.
c Select 'Save configuration' to save any changes but to continue to use the previous configuration.
d Save the configuration in internal or external storage.
Note.
A configuration file is saved with the filename '<time><date><>instrument tag>.cfg'
When a current configuration is saved to external storage, it is also saved automatically to internal storage.
e Select 'Cancel' to discard all changes and return to the Operating level.
IM/SM500F Issue 10.1
33
Field Mountable Videographic Recorder
SM500F 7 Specification
7 Specification
Operation and Configuration
Configuration
Via tactile membrane keys on front panel or PC Configuration
Multiple configuration files can be stored in internal (up to 16 files) or external memory (with removable media option fitted)
Security
Physical
Optional lock on door
Configuration security
Password protection Access to configuration is allowed only after the user has entered a password
Internal switch protection
Access to configuration is allowed only after a hardware switch has been set. This switch is situated behind a tamper-evident seal
Logging security
Configuration Can be configured for password protection or free access to logging levels
Basic type security
4 individual users with unique usernames and passwords
Advanced type security
Number of users
Usernames
Up to 12
Up to 20 characters. Usernames are unique (names cannot be repeated)
Access privileges Logging access – Yes/No
Configuration access
None/Load file only/Limited/Full
Passwords Up to 20 characters
A minimum required password length of 4 to 20 characters can be configured and a password expiry time can be applied to eliminate password ageing
Password failure limit Configurable for 1 to 10 consecutive occasions or
'infinite'
A user is deactivated if a wrong password is entered repeatedly
Deactivation of inactive users
Can be disabled or configured for 7, 14, 30, 60, 90,
180 or 360 days of inactivity
Users are deactivated (by removal of access privileges) after a period of inactivity
34 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
Custom Linearization
Number
2
Number of breakpoints
20 per linearizer
7 Specification
Operator Messages
Number
24
Trigger
Via front panel or digital signals
Recording in alarm/event log
Can be enabled or disabled on configuration
Display
Monochrome FSTN or Color TFT, passive matrix, liquid crystal display (LCD) with built-in backlight and contrast adjustment
Diagonal display area color 144 mm (5.7 in.) monochrome 120 mm (4.7 in.)
76800 pixel display*
* A small percentage of the display pixels may be either constantly active or inactive. Max. percentage of inoperative pixels <0.01%.
Language
English, German, French, Italian and Spanish
Dedicated operator keys
Group select/Left cursor
View select/Right cursor
Menu key
Up/Increment key
Down/Decrement key
Enter key
Chart screen intervals
Selectable from 18 s to 7 days
Chart divisions
Programmable for up to 10 major and 10 minor divisions
Chart annotation
Alarm and operator messages may be annotated on the chart
Icons to identify the type of event, time of occurrence and tag are displayed
IM/SM500F Issue 10.1
35
Field Mountable Videographic Recorder
SM500F
Process Alarms
Number
16 (4 per recording channel)
Types
High/Low process, latch & annunciator
Rate fast/slow
Tag
20-character tag for each alarm
Hysteresis
Programmable value and time hysteresis (1 to 9999 s)
Alarm enable
Allows alarm to be enabled/disabled via a digital input
Alarm log enable
Recording of alarm state changes in the alarm/event log can be enabled/disabled for each alarm
Acknowledgement
Via front panel keys or digital signals
7 Specification
Real-time Alarms
Number
4
Programmable
Day of the week, 1st of month, start and duration times
Recording to Internal Memory
Data Channels
Internal buffer memory
8 Mb Flash memory provides storage for 2 million samples
Oldest data is overwritten automatically by new data when memory is full
Data integrity checks
Checksum for each block of data samples
Independent process groups
2
No. of recording channels
4 per group
Sources
Analog inputs, Modbus™ inputs, any digital signal, math block
Filters
Programmable for each channel to allow recording of: instantaneous values, average, max., min. and max. & min. value over sample time
Primary/Secondary sample rates
Programmable from 0.1 s to 12 hours for each process group
Primary/Secondary sample rate selection
Via any digital signal or from password protected menu
Recording start/stop control
Via any digital signal or from password-protected menu
36 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 7 Specification
Recording Duration
Approximate duration calculated for continuous recording of 4 channels of analog data (for 8 channels divide by 2, for 2 channels multiply by 2 etc.)
Sample Rate
8 Mb Internal Flash
Buffer Memory
1 s
6 days
10 s
2 months
40 s
7.5 months
60 s
1 year
120 s
2 years
480 s
7 years
Archiving to Removable Media
Removable storage media options
SD Card
Data that can be saved to removable media
Recorded data for group 1 & 2 channels
Alarm event log data
Totalizer log data
Audit log data
Configuration
Screen capture images
File structure
Configurable as either binary-encoded or comma-separated
Filename
20-character tag, prefixed with date/time
Data verification
Carried out automatically on all writes to removable-media files
Card Compatibility
ABB recorders comply with approved industry standards for memory cards and ABB has fully tested and recommend the use of SanDisk Standard Grade memory cards. Other brands may not be fully compatible with this device and therefore may not function correctly.
Card Size
Cards up to 2 Gb capacity may be used
IM/SM500F Issue 10.1
37
Field Mountable Videographic Recorder
SM500F
Recording Duration
Approximate duration calculated for continuous recording of 4 channels of analog data
(for 8 channels divide by 2, for 2 channels multiply by 2 etc.)
Binary Encoded File
Sample Rate
128 Mb SD
256 Mb SD
512 Mb SD
1 Gb SD
1s
3 months
6 months
12 months
2 years
7 Specification
10s
2.5 years
5 years
10 years
20 years
Comma-separated File
Sample Rate
128 Mb SD
256 Mb SD
512 Mb SD
1 Gb SD
1s
28 days
8 weeks
16 weeks
7 months
10s
9 months
19 months
3 years
6 years
38 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 7 Specification
Historical Logs
Types
Alarm/Event, Totalizer and Audit logs
No. of records in each historical log
Up to 200 in internal memory
Oldest data is overwritten automatically by new data when log is full
Log Type Alarm/Event Log Totalizer Log
Log Entry
Events
Alarm state changes
Operator messages
User-defined logging intervals
Totalizer stop/start, reset, wrap
Power up/down
In Log On Screen In Log On Screen
Information
Recorded in
Log
Date & time of event
Type of event
Tag
Source tag
Alarm trip value & units of measure
Alarm state
Alarm acknowledge ment state
Operator ID
Description
–
–
–
–
–
Batch total and units of measurement*
Max., min. and average values plus units*
–
–
Secure total – –
* If Totalizer option is enabled and selected
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Audit Log
Configuration/calibration changes
System events
Errors, operator actions
In Log On Screen
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
IM/SM500F Issue 10.1
39
Field Mountable Videographic Recorder
SM500F
Analog/Digital Inputs
General
Number of inputs
4 (1 as standard, 3 optional)
Input types mA, mV, voltage, resistance, THC, 3-wire RTD, 4-wire RTD, volt-free digital, 24 V DC digital
Thermocouple types
B, E, J, K, L, N, R, S, T
Resistance thermometer
PT100
Other linearizations
√ x, x 3 /
2
, x 5 /
2
, custom linearization
Digital filter
Programmable 0 to 60s
Display range
–99999 to +999999
Common mode noise rejection
>120 dB at 50/60 Hz with 300 Ω imbalance resistance
Normal (series) mode noise rejection
>60 dB at 50/60 Hz
CJC rejection ratio
0.05 °C/°C
Sensor break protection
Programmable as upscale or downscale
Temperature stability
0.02 %/°C or 2 µV/°C
Long term drift
<0.2 % of reading or 20 µV annually
Input impedance
>10 M
Ω
(millivolts inputs)
>10 M Ω (voltage inputs)
44 Ω (mA inputs)
7 Specification
40 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F
Standard Analog Input Modules
Linear Inputs
Millivolts
Milliamps
Volts
Resistance Ω (low)
Resistance Ω (high)
Digital Input Specification
Sample Interval
Input Isolation
Isolation from Rest of Instrument
7 Specification
Standard Analog Input
Accuracy
(% of reading)
0 to 150 mV
0 to 50 mA
0 to 25 V
0 to 550 Ω
0 to 10 k Ω
0.1 % or ±20 µV
0.2 % or ±4 µA
0.2 % or ±1 mV
0.1 % or ±0.1 Ω
0.1 % or ±0.5 Ω
Switching threshold 4 V – Min. pulse width of On or Off state 500 ms
100 ms per sample
500 V DC channel-to-channel
Galvanically isolated to 500 V DC
Analog Input Types
Thermocouple Maximum
Range °C
–18 to 1800
Maximum Range
°F
0 to 3270
Accuracy (% of reading)
B
E
0.1 % or ±2 °C (3.6 °F) (above 200 °C [392 °F]) *
0.1 % or ±0.5 °C (0.9 °F) –100 to 900
–100 to 900
–140 to 1650
–140 to 1650 J
K
0.1 % or ±0.5 °C (0.9 °F)
0.1 % or ±0.5 °C (0.9 °F) –100 to 1300
–100 to 900
–140 to 2350
–140 to 1650 L
N
0.1 % or ±1.5 °C (2.7 °F)
0.1 % or ±0.5 °C (0.9 °F) –200 to 1300
–18 to 1700
–325 to 2350
0 to 3000 R
S
0.1 % or ±1 °C (1.8 °F) (above 300 °C [540 °F]) *
0.1 % or ±1 °C (1.8 °F) (above 200 °C [392 °F]) * –18 to 1700
–250 to 300
0 to 3000
–400 to 550 T 0.1 % or ±0.5 °C (0.9 °F) (above –150 °C [–238 °F]) *
* For B, R, S and T thermocouples, accuracy is not guaranteed below the value stated.
RTD
PT100
Maximum
Range °C
–200 to 600
Maximum Range
°F
–325 to 1100
Accuracy (% of reading)
0.1 % or ±0.5 °C (0.9 °F)
IM/SM500F Issue 10.1
41
Field Mountable Videographic Recorder
SM500F
Relays
Number of relays
1 as standard, 2 optional, (1 Module)
Type and rating
Relay type
Voltage
Current
Loading (non-inductive)
Selectable NO/NC
250 V AC
5 A AC
1250 VA
30 V DC
5 A DC
150 W
7 Specification
2-Wire Transmitter Power Supply (optional)
Number
2 isolated supplies
Voltage
24 V DC nominal
Drive
22 mA (each supply)
Ethernet Module (optional)
Physical medium
10BaseT
Protocols
TCP/IP, FTP (server), HTTP, SMTP, Modbus TCP (Client + Server)
FTP server functions
Directory selection & listing
File upload/download
4 independently configurable users with full or read-only access
Web server functions
Operator screen monitoring/selection. Remote monitoring of recording channels, analog/digital signals, alarms, totalizers and archiving.
Totalizer (optional)
Number
2 per recording channel, 10-digit totals
Type
Analog or digital
Statistical calculations
Average, maximum, minimum (for analog signals)
42 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F 7 Specification
Advanced Math (optional)
Type
8 equations provide ability to perform general arithmetic calculations including F0, mass flow (of ideal gases), relative humidity and emissions calculations
Size
40-character equation
Functions
+, –, /, log, Ln., Exp, X n ,
√
, Sin, Cos, Tan, mean, rolling average, standard deviation, high/median/low select, multiplexer, absolute, relative humidity
Tags
8- and 20-character tags for each block
Update rate
1 enabled Math block is updated every 100 ms
Logic Equations (optional)
Number
8
Size
11 elements each
Functions
AND, OR, NAND, NOR, XOR, NOT
Tags
20-character tag for each equation
Update rate
300 ms
EMC
Emissions & immunity
Meets requirements of IEC61326 for an Industrial Environment
Electrical
Supply ranges
85 V min. to 265 V max. AC 50/60 Hz or
105 V DC min. to 115 V DC max.
10 V to 36 V DC (optional)
Power consumption
10 W max.15 VA max.
Power interruption protection
No effect for interrupts of up to 20 ms
IM/SM500F Issue 10.1
43
Field Mountable Videographic Recorder
SM500F
Safety
General safety
EN61010-1
Overvoltage Class III on mains, Class II on inputs and outputs
Pollution category 2
CSA 1010 (pending)
UL 1010
Isolation
500 V DC to earth (ground)
Environmental
Operating temperature range
–10 to 50 °C (14 to 122 °F)
Operating humidity range
5 to 95 %RH (non-condensing)
Storage temperature range
–20 to 70 °C (–4 to 174 °F)
Enclosure sealing
IP66 and NEMA4X (the enclosure meets the requirements of the NEMA 4X hosedown test)
Physical
Size
144 mm (5.7 in.) x 144 mm (5.7 in.) x 84 mm (3.3 in.)
Weight
1.0 kg (2.2 lb) approx. (unpacked)
Panel cutout
138 mm (5.43 in.) x 138 mm (5.43 in.) x 67 mm (2.7 in.) behind panel
Case material
Glass-filled polycarbonate
Operator keypad
Tactile membrane keys
No. of keys
6
7 Specification
SS/SM500F Issue 14
44 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F Appendix A – Signal Sources
Appendix A – Signal Sources
Source Name
Analog Sources
Description
Analog I/P A1 to D1
Comms AIN 1 to 24
Stats 1.1 to 1.4 max
Stats 2.1 to 2.4 max
Stats 1.1 to 1.4 min
Stats 2.1 to 2.4 min
Stats 1.1 to 1.4 avg
Stats 2.1 to 2.4 avg
Analog input values (from Analog input module).
Available only if an analog input module is fitted in the relevant position.
Analog input values .
Received via the Modbus serial communications link – see Table B.14 on page 54.
Maximum Statistics Input Value .
Value since the totalizer on a given channel last wrap or reset. Available only if the totalizer option is enabled, only on analog channels and only if the relevant totalizer is enabled in the Configuration level.
Minimum Statistics Input Value .
Value since the totalizer on a given channel last wrap or reset. Available only if the totalizer option is enabled, only on analog channels and only if the relevant totalizer is enabled during configuration.
Average Statistics Input Value .
Value since the totalizer on a given channel last wrap or reset. Available only if the totalizer option is enabled, only on analog channels and only if the relevant totalizer is enabled during configuration.
Error States
AIN A1 to D1 Fail State
Comms AIN 1 to 6 Fail State
Stats 1.1 to 1.4 fail
Stats 2.1 to 2.4 fail
Archive media not present
Too many files on arc media
Archive 100% full
Archive 80% full
Arc media present
Archive on-line
Table A.1 Signal Sources
Analog Input Failure .
Active when the signal detected at the analog input is outside the 'Fault Detect Level' specified during configuration.
Totalizer Input Value Failure .
Activated when the totalizer fails, cleared when the totalizer wraps or is reset. Available only if the totalizer option is enabled, only on analog channels and only if the relevant totalizer is enabled during configuration.
Active when the removable archive media is not present.
Active when there are approximately 300 files on the removable archive media.
Active when the removable archive media is 100% full
Active when the removable archive media is 80% full.
Active when the removable archive media is present.
Active when archiving is in progress.
IM/SM500F Issue 10.1
45
Field Mountable Videographic Recorder
SM500F Appendix A – Signal Sources
Source Name
Digital Input States
Description
Digital I/P A1 to D1
Comms Dig I/P 1 to 24
Alarm state 1.1A to 2.4D
Alarm ack state 1.1A to 2.4D
Alarm group 1 to 12
Any Alarm
New Alarm
Real time alarm 1 to 4
Run state 1.1 to 2.4
Wrap pulse 1.1 to 2.4
1st Stage O/P 1.1 to 2.4
Count pulse 1.1 to 2.4
Digital Input States .
Digital signals received from analog input modules fitted at module positions A to D if input 'Type' is set to 'Volt free digital input' during configuration. Available only if the module is fitted.
Digital Input States .
Digital signals received via Modbus serial link – see Table B.14 on page 54.
Alarm States .
Available only if the relevant alarm is enabled during configuration.
Alarm Acknowledge States .
Available only if the relevant alarm is enabled during configuration. Acknowledged alarm = 0; Unacknowledged alarm = 1. Process, Latch and Annunciator alarms only.
Alarm Groups .
Available only if any alarms are enabled during configuration. Active only if any of the alarms assigned to a group are active.
Available only if there is at least one alarm enabled during configuration. Active only if any of the enabled alarms are active.
Available only as a source for e-mail triggers. Causes an e-mail to be generated if any alarm becomes active.
Real Time Alarm States .
Available only if the relevant alarm is enabled during configuration.
Totalizer Run States .
Active while totalizer is running. Available only if the relevant totalizer is enabled in the configuration level.
Totalizer Wrap Pulse .
Available only if the totalizer option is enabled and the relevant totalizer is enabled during configuration.
If 'Wrap Enable' set to 'On' – active for 1 second when the predetermined count has been reached.
If 'Wrap Enable' set to 'Off' – active when the predetermined count is been reached and remains active until the totalizer is reset
Totalizer First Stage Output (Intermediate Count) .
Active for 1 second when the intermediate count has been reached. Available only if the totalizer option is enabled and the relevant totalizer is enabled during configuration.
Totalizer Count Pulse .
Active for 100ms each time the totalizer updates by one whole count. E.g. if two decimal places are set, a pulse is generated when the totalizer value increments from
0.99 to 1.00 or 1.99 to 2.00
Table A.1 Signal Sources (Continued)
46 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
Appendix B – ModbusTCP Guide
B.1 Introduction
The instrument can be configured to act as either a ModbusTCP client or server.
If configured as a client the recorder collects data from ModbusTCP servers (or RTUs via a gateway) into its
Comms Analog and Comms Digital Channels.
If configured as a server the recorder responds to Modbus queries transferred via the ModbusTCP protocol for the registers described in this appendix.
B.2 Modbus Commands Supported
The following Modbus commands are supported:
01 Read Coil Status – reads the on/off status of 16 consecutive digital states, starting at a specified address. The instrument returns zeros for points which do not contain defined data.
03 Read Holding Registers – reads 8 consecutive analog values, starting from a specified address. The instrument returns zeros for registers which do not contain defined data.
05 Force Single Coil – Sets the value of a single coil (digital signal) at the specified address. The data value must be FF00Hex to set the signal ON and zero to turn it OFF. The instrument returns an exception response if the register is not currently writable.
06 Preset Single Register – Sets the value of a single register (analog value) at the specified address.
The instrument returns an exception response if the register is not currently writable. Limits defined in configuration are applied to the value before storage.
15 Force Multiple Coils – The instrument carries out updates that are valid and returns an exception response if any of the coils are not currently writable.
16 Preset Multiple Registers – The instrument carries out updates that are valid and generates an exception response if any of the registers are not currently writable.
Note.
Negative numbers are represented in '2's complement' format, for example, 1000 = 03E8 (Hex),
–1000 = FC18 (Hex)
B.3 Modbus Exception Responses – Table B.1
If the instrument detects one of the errors shown in Table B.1 while receiving a message from the host system, it replies with a response message consisting of the instrument's Modbus address, the function code, the error code and the error check fields.
Code
01
02
03
07
08
Name
Illegal Function
Illegal Data Address
Illegal Data Value
Definition
The message function received is not an allowable action
The address reference in the data field is not an allowable address
The value referenced in the data field is not allowable in the addressed slave
Negative Acknowledgement Received message error
Memory Parity Error Parity check indicates an error in one or more of the characters received
Table B.1 Modbus Exception Responses
IM/SM500F Issue 10.1
47
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
B.4 Operating Mode Modbus Coils – Tables B.2 to B.10
Tables B.2 to B.10 detail the contents of each Modbus coil. Each coil is assigned a register that can have one of two values: 0000 and 0001.
Analog Input
A1
B1
C1
D1
Read Only: 0 = Input OK, 1 = Input Failed
Modbus Coil
0001
0002
0003
0004
Table B.2 Analog Input Fail States
Alarm
Active/Inactive
Alarm Acknowledged
Read
Access
0 = Alarm inactive
1 = Alarm active
Write
Access
1.3C
1.3D
1.4A
1.4B
1.4C
1.4D
Alarm
1.1A
1.1B
1.1C
1.1D
1.2A
1.2B
1.2C
1.2D
1.3A
1.3B
None
Modbus Coil
0051
0052
0053
0054
0055
0056
0057
0058
0059
0060
0061
0062
0063
0064
0065
0066
0 = Acknowledged or inactive
1 = Active and unacknowledged
0 = No effect
1 = Acknowledge
Modbus Coil
0101
0102
0103
0104
0105
0106
0107
0108
0109
0110
0111
0112
0113
0114
0115
0116
Table B.3 Alarm States
Alarm
Active/Inactive
Alarm Acknowledged
Read
Access
0 = Alarm inactive
1 = Alarm active
Write
Access
2.3C
2.3D
2.4A
2.4B
2.4C
2.4D
Alarm
2.1A
2.1B
2.1C
2.1D
2.2A
2.2B
2.2C
2.2D
2.3A
2.3B
None
Modbus Coil
0067
0068
0069
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
0080
0081
0082
0 = Acknowledged or inactive
1 = Active and unacknowledged
0 = No effect
1 = Acknowledge
Modbus Coil
0117
0118
0119
0120
0121
0122
0123
0124
0125
0126
0127
0128
0129
0130
0131
0132
48 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
Title
Operator Message 1
Operator Message 2
Operator Message 3
Operator Message 4
Operator Message 5
Operator Message 6
Operator Message 7
Operator Message 8
Operator Message 9
Operator Message 10
Operator Message 11
Operator Message 12
Read: Always returns '0'
Write: 1 = Activate
Coil Number
0151
0152
0153
0154
0155
0156
0157
0158
0159
0160
0161
0162
Title
Operator Message 13
Operator Message 14
Operator Message 15
Operator Message 16
Operator Message 17
Operator Message 18
Operator Message 19
Operator Message 20
Operator Message 21
Operator Message 22
Operator Message 23
Operator Message 24
Reserved
Read: Always returns '0'
Write: 1 = Activate
Coil Number
0163
0164
0165
0166
0167
0168
0169
0170
0171
0172
0173
0174
0175 to 0180
Table B.4 Operator Messages
Title
Assign to Group 1
Assign to Group 2
Activate Remote
Operator Message
Coil Number Read
0181
0 = Remote operator message not assigned to group
0182
0183 Always reads as 0
Write
0 = Unassign remote operator message from group
1 = Remote operator message assigned to group
1 = Assign remote operator message to group
0 = No effect
1 = Activate
Table B.5 Remote Operator Messages
IM/SM500F Issue 10.1
49
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
1.3A
1.3B
1.4A
1.4B
2.1A
2.1B
2.2A
2.2B
Stop/Go
Read Access 0 = Stopped
1 = Running
Write Access 0 = Stop
1 = Start
Totalizer
1.1A
Modbus Coil
0351
1.1B
1.2A
1.2B
0352
0353
0354
2.3A
2.3B
2.4A
2.4B
* Time since last reset
0355
0356
0357
0358
0359
0360
0361
0362
0363
0364
0365
0366
Table B.6 Totalizer Digital Signals
Reset
0 = >1s*
1 = <1s*
1 = Reset
Modbus Coil
0401
0402
0403
0404
0405
0406
0407
0408
0409
0410
0411
0412
0413
0414
0415
0416
Modbus Registers
Wrap Pulse
0 = Inactive
1 = Active
1st Stage Pulse Flowrate Failure
0 = Inactive
1 = Active
0 = Inactive
1 = Active
Modbus Coil
0451
0452
0453
0454
0455
0456
0457
0458
0459
0460
0461
0462
0463
0464
0465
0466
Modbus Coil
0501
0502
0503
0504
0505
0506
0507
0508
0509
0510
0511
0512
0513
0514
0515
0516
Modbus Coil
0551
0552
0553
0554
0555
0556
0557
0558
0559
0560
0561
0562
0563
0564
0565
0566
Read Only: 0 = All alarms inactive
1 = At least 1 alarm active
Coil Number Title
Any Alarm
Table B.7 Any Alarm
0750
Title
Alarm Group 1
Alarm Group 2
Alarm Group 3
Alarm Group 4
Alarm Group 5
Alarm Group 6
Table B.8 Alarm Groups
Read Only: 0 = Alarm group inactive
1 = Alarm group active
Coil Number
0751
0752
0753
0754
0755
0756
Title
Alarm Group 7
Alarm Group 8
Alarm Group 9
Alarm Group 10
Alarm Group 11
Alarm Group 12
Read Only: 0 = Alarm group inactive
1 = Alarm group active
Coil Number
0757
0758
0759
0760
0761
0762
50 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
Title
Real Time Alarm 1
Read Only: 0 = Real time alarm inactive
1 = Real time alarm active
Coil Number
0851
Real Time Alarm 2
Real Time Alarm 3
Real Time Alarm 4
0852
0853
0854
Table B.9 Real Time Alarms
Signal
Channel Fail Status
Alarm A
Alarm B
Alarm C
Alarm D
Alarm A Acknowledge
Alarm B Acknowledge
Alarm C Acknowledge
Alarm D Acknowledge
Totalizer A Stop/Go
Totalizer A Reset
Totalizer A Wrap
Totalizer A First Stage
Totalizer A Flowrate Fail
Totalizer B Stop/Go
Totalizer B Reset
Totalizer B Wrap
Totalizer B First Stage
Totalizer B Flowrate Fail
Channel Type
Digital Value
Table B.10 Channel Digital Signals
Read Only
Read Only
Read Only
Read Only
1.1
1001
1002
1003
1004
Read Only 1005
Read/Write 1006
Read/Write 1007
Read/Write 1008
Read/Write 1009
Read/Write 1010
Read/Write 1011
Read Only 1012
Read Only
Read Only
1013
1014
Read/Write 1015
Read/Write 1016
Read Only
Read Only
Read Only
Read Only
Read Only
1017
1018
1019
1020
1021
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1.2
1031
1032
1033
1034
1035
1036
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
Channel
1.4
2.1
1091
1092
1121
1122
1093
1094
1095
1096
1123
1124
1125
1126
1135
1136
1137
1138
1139
1140
1141
1127
1128
1129
1130
1131
1132
1133
1134
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1.3
1061
1062
1063
1064
1065
1066
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
2.3
1181
1182
1183
1184
1185
1186
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
2.2
1151
1152
1153
1154
1155
1156
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
2.4
1211
1212
1213
1214
1215
1216
IM/SM500F Issue 10.1
51
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
B.5 Operating Mode ModbusTCP Registers – Tables B.11 to B.13
Tables B.11 to B.13 detail the contents of the ModbusTCP registers accessible while the instrument is in the operating mode.
Two data types are used:
32-bit single precision floating point data in IEEE format
64-bit double precision floating point data in IEEE format
Note.
When writing to a parameter that occupies more than one register position then all registers relating to that parameter MUST be written to as part of a multiple register write. If this is not achieved a NAK exception response is issued. Individual registers can be read without causing an exception response.
When accessing a parameter that occupies more than one register position, the lowest numbered register contains the most significant data.
Analog Input
A1
B1
C1
D1
Table B.11 Analog Inputs
Read Only, single precision IEEE floating point number
Modbus Register
0001 and 0002
0003 and 0004
0005 and 0006
0007 and 0008
1.3B
1.3C
1.3D
1.4A
1.4B
1.4C
1.4D
Alarm
1.1A
1.1B
1.1C
1.1D
1.2A
1.2B
1.2C
1.2D
1.3A
Table B.12 Alarm Trip Levels
Trip Point Registers
0101 and 0102
0103 and 0104
0105 and 0106
0107 and 0108
0109 and 0110
0111 and 0112
0113 and 0114
0115 and 0116
0117 and 0118
0119 and 0120
0121 and 0122
0123 and 0124
0125 and 0126
0127 and 0128
0129 and 0130
0131 and 0132
2.3B
2.3C
2.3D
2.4A
2.4B
2.4C
2.4D
Alarm
2.1A
2.1B
2.1C
2.1D
2.2A
2.2B
2.2C
2.2D
2.3A
Trip Point Registers
0133 and 0134
0135 and 0136
0137 and 0138
0139 and 0140
0141 and 0142
0143 and 0144
0145 and 0146
0147 and 0148
0149 and 0150
0151 and 0152
0153 and 0154
0155 and 0156
0157 and 0158
0159 and 0160
0161 and 0162
0163 and 0164
52 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
IEEE
Totalizer
1.1A
1.1B
1.2A
1.2B
1.3A
1.3B
1.4A
1.4B
2.1A
2.1B
2.2A
2.2B
2.3A
2.3B
2.4A
2.4B
Maximum
Flowrate
0251 and
0252
0253 and
0254
0255 and
0256
0257 and
0258
0259 and
0260
0261 and
0262
0263 and
0264
0265 and
0266
0267 and
0268
0269 and
0270
0271 and
0272
0273 and
0274
0275 and
0276
0277 and
0278
0279 and
0280
0281 and
0282
Table B.13 Totalizer Totals
Minimum
Flowrate
0301 and
0302
0303 and
0304
0305 and
0306
0307 and
0308
0309 and
0310
0311 and
0312
0313 and
0314
0315 and
0316
0317 and
0318
0319 and
0320
0321 and
0322
0323 and
0324
0325 and
0326
0327 and
0328
0329 and
0330
0331 and
0332
Current Batch
IEEE IEEE
Double
Precision
Floating
Point
Average
Flowrate
0351 and
0352
0353 and
0354
0355 and
0356
0357 and
0358
0359 and
0360
0361 and
0362
0363 and
0364
0365 and
0366
0367 and
0368
0369 and
0370
0371 and
0372
0373 and
0374
0375 and
0376
0377 and
0378
0379 and
0380
0381 and
0382
Batch Total
0401 to
0404
0405 to
0408
0409 to
0412
0413 to
0416
0417 to
0420
0421 to
0424
0425 to
0428
0429 to
0432
0433 to
0436
0437 to
0440
0441 to
0444
0445 to
0448
0449 to
0452
0453 to
0456
0457 to
0460
0461 to
0464
IEEE
Maximum
Flowrate
0551 and
0552
0553 and
0554
0555 and
0556
0557 and
0558
0559 and
0560
0561 and
0562
0563 and
0564
0565 and
0566
0567 and
0568
0569 and
0570
0571 and
0572
0573 and
0574
0575 and
0576
0577 and
0578
0579 and
0580
0581 and
0582
Minimum
Flowrate
0601 and
0602
0603 and
0604
0605 and
0606
0607 and
0608
0609 and
0610
0611 and
0612
0613 and
0614
0615 and
0616
0617 and
0618
0619 and
0620
0621 and
0622
0623 and
0624
0625 and
0626
0627 and
0628
0629 and
0630
0631 and
0632
Previous Batch
IEEE IEEE
Double
Precision
Floating
Point
Average
Flowrate
0651 and
0652
0653 and
0654
0655 and
0656
0657 and
0658
0659 and
0660
0661 and
0662
0663 and
0664
0665 and
0666
0667 and
0668
669 and
0670
0671 and
0672
0673 and
0674
0675 and
0676
0677 and
0678
0679 and
0680
0681 and
0682
Batch Total
0701 to
0704
0705 to
0708
0409 to
0412
0713 to
0716
0717 to
0720
0721 to
0724
0725 to
0728
0729 to
0732
0733 to
0736
0737 to
0740
0441 to
0444
0745 to
0748
0749 to
0752
0753 to
0756
0757 to
0760
0761 to
0764
IM/SM500F Issue 10.1
53
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
B.6 Communications – Analog and Digital Inputs
Comms.
Digital
Inputs
Comms.
Analog
Inputs
Failure
Comms.
Analog Inputs
Read/Write:
0 = Inactive
1 = Active
10
11
12
8
9
6
7
Input
Number
1
4
5
2
3
Coil Number Coil Number
0601
0602
0603
0604
0605
0606
0607
0608
0609
0610
0611
0612
0651
0652
0653
0654
0655
0656
0657
0658
0659
0660
0661
0662
Floating point
(–999 to 9999)
Registers
0851 and 0852
0853 and 0854
0855 and 0856
0857 and 0858
0859 and 0860
0861 and 0862
0863 and 0864
0865 and 0866
0867 and 0868
0869 and 0870
0871 and 0872
0873 and 0874
Comms.
Digital
Inputs
Comms.
Analog
Inputs
Failure
Comms.
Analog Inputs
Read/Write:
0 = Inactive
1 = Active
Floating point
(–999 to 9999)
Input
Number
13
14
15
16
17
18
19
20
21
22
23
Coil Number Coil Number
0613
0614
0615
0616
0617
0618
0619
0620
0621
0622
0623
0663
0664
0665
0666
0667
0668
0669
0670
0671
0672
0673
Registers
0875 and 0876
0877 and 0878
0879 and 0880
0881 and 0882
0883 and 0884
0885 and 0886
0887 and 0888
0889 and 0890
0891 and 0892
0893 and 0894
0895 and 0896
24 0624 0674 0897 and 0898
Reserved 0625 to 0650 0675 to 0700 0899 to 1000
Table B.14 Modbus Inputs
54 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
Totalizer A
Average
Totalizer A
Total
Totalizer A
Max
Totalizer A
Min
Totalizer A
Average
Totalizer A
Total
Totalizer B
Max
Totalizer B
Min
Totalizer B
Average
Totalizer B
Total
Totalizer B
Max
Signal
Channel
Input
Alarm A
Trip
Alarm B
Trip
Alarm C
Trip
Alarm D
Trip
Totalizer A
Max
Totalizer A
Min
Totalizer B
Min
Totalizer B
Average
Totalizer B
Total
Table B.15 Channel Data
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read
Only
Read/
Write
Read/
Write
Read/
Write
Read/
Write
Read
Only
Read
Only
Read
Only
1.1
1.2
1001 and
1002
1051 and
1052
1003 and
1004
1053 and
1054
1005 and
1006
1055 and
1056
1007 and
1008
1057 and
1058
1009 and
1010
1059 and
1060
1011 and
1012
1061 and
1062
1013 and
1014
1063 and
1064
1015 and
1016
1065 and
1066
1017 to
1020
1067 to
1070
1021 and
1022
1071 and
1072
1023 and
1024
1073 and
1074
1025 and
1026
1075 and
1076
1027 to
1030
1077 to
1080
1031 and
1032
1081 and
1082
1033 and
1034
1083 and
1084
1115 and
1116
1117 to
1120
1121 and
1122
1123 and
1124
1125 and
1126
1127 to
1130
1131 and
1132
1133 and
1134
1.3
1101 and
1102
1103 and
1104
1105 and
1106
1107 and
1108
1109 and
1110
1111 and
1112
1113 and
1114
1.4
Channel
1151 and
1152
1153 and
1154
1155 and
1156
1157 and
1158
1159 and
1160
1161 and
1162
1163 and
1164
1165 and
1166
1167 to
1170
1171 and
1172
1173 and
1174
1175 and
1176
1177 to
1180
1181 and
1182
1183 and
1184
2.1
1201 and
1202
1203 and
1204
1205 and
1206
1207 and
1208
1209 and
1210
1211 and
1212
1213 and
1214
1215 and
1216
1217 to
1220
1221 and
1222
1223 and
1224
1225 and
1226
1227 to
1230
1231 and
1232
1233 and
1234
1035 and
1036
1085 and
1086
1037 to
1040
1087 to
1090
1041 and
1042
1091 and
1092
1135 and
1136
1137 to
1140
1141 and
1142
1043 and
1044
1093 and
1094
1045 and
1046
1095 and
1096
1047 to
1050
1097 to
1100
1143 and
1144
1145 and
1146
1147 to
1150
1185 and
1186
1235 and
1236
1187 to
1190
1237 to
1240
1191 and
1192
1241 and
1242
1285 and
1286
1287 to
1290
1291 and
1292
1193 and
1194
1243 and
1244
1195 and
1196
1245 and
1246
1197 to
1200
1247 to
1250
1293 and
1294
1295 and
1296
1297 to
1300
1265 and
1266
1267 to
1270
1271 and
1272
1273 and
1274
1275 and
1276
1277 to
1280
1281 and
1282
1283 and
1284
2.2
1251 and
1252
1253 and
1254
1255 and
1256
1257 and
1258
1259 and
1260
1261 and
1262
1263 and
1264
2.3
2.4
1301 and
1302
1351 and
1352
1303 and
1304
1353 and
1354
1305 and
1306
1355 and
1356
1307 and
1308
1357 and
1358
1309 and
1310
1359 and
1360
1311 and
1312
1361 and
1362
1313 and
1314
1363 and
1364
1315 and
1316
1365 and
1366
1317 to
1320
1367 to
1370
1321 and
1322
1371 and
1372
1323 and
1324
1373 and
1374
1325 and
1326
1375 and
1376
1327 to
1330
1377 to
1380
1331 and
1332
1381 and
1382
1333 and
1334
1383 and
1384
1335 and
1336
1385 and
1386
1337 to
1340
1387 to
1390
1341 and
1342
1391 and
1392
1343 and
1344
1393 and
1394
1345 and
1346
1395 and
1396
1347 to
1350
1397 to
1400
IM/SM500F Issue 10.1
55
Field Mountable Videographic Recorder
SM500F Appendix B – ModbusTCP Guide
Input
Character 1
Character 2
Character 3
Character 4
Character 5
Character 6
Character 7
Read/ Write: ASCII Character Code – see Table B.17
Register Number
0951
Input
Character 8
Register Number
0958
Input
Character 15
0952
0953
Character 9
Character 10
0959
0960
Character 16
Character 17
0954
0955
0956
0957
Character 11
Character 12
Character 13
Character 14
0961
0962
0963
0964
Character 18
Character 19
Character 20
Table B.16 Remote Operator Messages
Register Number
0965
0966
0967
0968
0969
0970
23
24
25
26
Hex Dec Char
20 32 Space
21
22
33
34
!
“
35
36
37
38
#
$
%
&
31
32
33
27
28
29
2A
2B 43
2C 44
2D
2E
2F
30
45
46
47
48
39
40
41
42
49
50
51
1
2
3
+
N/A
-
.
/
0
*
)
(
`
Hex Dec Char
34 52 4
35 53
36 54
37 55
38 56
39 57
3A 58
3B 59
3C 60
3D 61
3E
3F
40 64
41 65
42 66
43 67
44 68
45
46
62
63
69
70
5
6
7
8
9
;
:
<
=
>
?
@
A
B
C
D
E
F
4A
4B
4C
4D
Hex Dec Char
47 71 G
48
49
72
73
H
I
4E
4F
50
51
52
53
54
55
56
57
58
59
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
L
M
J
K
N
O
P
Q
R
S
T
U
V
W
X
Y
Hex Dec Char
5A 90 Z
5B 91
5C 92
5D
5E
5F
60
93
94
95
96
61
62
97
98
63 99
64 100
65 101
66 102
67 103
68 104
69 105
6A 106
6B 107
6C 108
]
^
_
N/A g h j i e f c d a b k l
[
\
Hex Dec Char
6D 109 m
6E 110
6F 111 n o
70 112
71 113
72 114
73 115 r s p q
74 116
75 117
76 118
77 119
78 120
79 121
7A 122
7B 123
7C 124
7D 125
7E 126 ~
7F 127 N/A v w t u z
{
|
} x y
Hex Dec Char
A3 163 £
B0
B2
176
178 ²
°
³ B3 179
B5 181
3A9 937
µ
Ω Note.
Character codes 2C, 60 and 7F Hex (44, 96 and 127 Dec) are not supported
Table B.17 ASCII Character Set for Remote Operator Messages
56 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F Appendix C – Storage Capacity
Appendix C – Storage Capacity
C.1 Internal Storage Capacity – Table C.1
Approximate duration calculated for continuous recording of 4 channels of analog data (for 8 channels divide by 2; for 2 channels multiply by 2 etc.).
10 seconds 40 seconds 60 seconds 120 seconds 480 seconds Sample Rate
8Mb internal Flash memory
1 second
6 days
Table C.1 Internal Storage Capacity
2 months 7.5 months 1 year 2 years 7 years
C.2 External Storage Capacity – Tables C.2 and C.3
Approximate duration calculated for continuous recording of 4 channels of analog data (for 8 channels divide by 2; for 2 channels multiply by 2 etc.).
256Mb
8 weeks
19 months
SD Card Size
Sample Rate
1.0 second
10.0 seconds
128Mb
28 days
9 months
Table C.2 External (Archive) Storage Capacity – Text Formatted Archive Files
512Mb
16 weeks
3 years
1Gb
7 months
6 years
256Mb
6 months
5 years
SD Card Size
Sample Rate
1.0 second
10.0 seconds
128Mb
3 months
2.5 years
Table C.3 External (Archive) Storage Capacity – Binary Formatted Archive Files
512Mb
12 months
10 years
1Gb
2 years
20 years
IM/SM500F Issue 10.1
57
Field Mountable Videographic Recorder
SM500F
Appendix D – Units
Ml/d
Ml/h
Ml/m
Ml/s l/d l/h l/m l/s
Unit deg F
Kelvin
%RH
% ppm ppb pH
Description
Degrees Fahrenheit
Degrees Kelvin
% Relative Humidity
% parts per million parts per billion potential Hydrogen liters per day liters per hour liters per minute liters per second megaliters per day megaliters per hour megaliters per minute megaliters per second gal/d (UK) imperial gallons per day gal/h (UK) imperial gallons per hour gal/m (UK) imperial gallons per minute gal/s (UK) imperial gallons per second
Mgal/d (UK) imperial mega gallons per day gal/d (US) US gallons per day gal/h (US) US gallons per hour gal/m (US) US gallons per minute gal/s (US) US gallons per second
Mgal/d (US) US mega gallons m3/d m3/h cubic meters per day cubic meters per hour m3/m m3/s ft3/d ft3/h cubic meters per minute cubic meters per second cubic feet per day cubic feet per hour
Table D.1 Engineering Units
Appendix D – Units g/h g/d ml/m ml/h
%dO2 uV mV
MV
% sat
%O2
%N2
%HCI
NTU
FTU
%OBS g/l ton/s ug/kg mg/kg mbar bar m WG
Hz kHz
Unit lb/d lb/h lb/m lb/s ton/d ton/h ton/m pounds per day
Description pounds per hour pounds per minute pounds per second imperial tons per day imperial tons per hour imperial tons per minute imperial tons per second micrograms per kilogram milligrams per kilogram millibar bar meters water gauge hertz kilohertz
% saturation
% oxygen
% nitrogen
% hydrochloric acid nephelometric turbidity units formazine turbidity units
% obscuration grams per liter grams per hour grams per day milliliters per minute milliliters per hour
% dissolved oxygen microvolts millivolts megavolts
58 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F kg/s
T/d
T/h
T/m
T/s
Unit ft3/m ft3/s
SCFM kg/d kg/h kg/m
Description cubic feet per minute cubic feet per second standard cubic feet per minute kilograms per day kilograms per hour kilograms per minute kilograms per second metric tonnes per day metric tonnes per hour metric tonnes per minute metric tonnes per second
Table D.1 Engineering Units (Continued)
Unit l ml kl
Ml m liters milliliters kiloliters megaliters meters gal (UK) imperial gallons
Description g x 10 (UK) imperial gallons x 10 g x100 (UK) imperial gallons x 100 kgal (UK) imperial kilo gallons
Mgal (UK) imperial mega gallons gal (US) us gallons g x 10 (US) us gallons x 10 g x100 (US) us gallons x 100 kgal (US) us kilo gallons
Mgal (US) us mega gallons
Table D.2 Totalizer Units
Appendix D – Units
Unit
A mho
S uS/cm amps conductance
Siemens
Description microSiemens per centimeter mS/cm milliSiemens per centimeter uS/m microSiemens per meter mS/m
Feet milliSiemens per meter imperial feet
Inches imperial inches
Custom user defined units
Unit m3 km3
Mm3 cubic meters
Description kilo cubic meters mega cubic meters
CUMEC cubic meter of water per second kg
T kilograms tons kT lb ton btu kilotons pounds imperial tons british thermal units ft3 kft3
Mft3 cubic feet kilo cubic feet mega cubic feet
AcreFt volume of water, 1ft deep, covering an area of 1 acre
Custom user defined units
IM/SM500F Issue 10.1
59
Field Mountable Videographic Recorder
SM500F Index
Index
A
Accessing the configuration level ...................................................................................................... 27
C
Configuration
Data entry dialog boxes ............................................................................................................. 31
Exiting configuration mode ......................................................................................................... 32
Locating parameter settings ....................................................................................................... 30
Overview .................................................................................................................................... 29
Configuration level security ............................................................................................................... 25
D
Displays and controls ....................................................................................................................... 20
I
E
Electrical installation
Cable entry ................................................................................................................................ 13
Cable glands .............................................................................................................................. 13
Cable screening connections ..................................................................................................... 13
Connections .............................................................................................................................. 15
AC and DC power supply connections ................................................................................... 17
Analog/digital input connections ............................................................................................. 16
Transmitter power supply module ........................................................................................... 18
Ethernet cable routing ................................................................................................................ 13
Fuses ................................................................................................................................... 12, 17
Knockout removal ...................................................................................................................... 13
Relays ........................................................................................................................................ 18
Thermocouple compensating cable ........................................................................................... 17
End of life disposal ............................................................................................................................. 5
Engineering units .............................................................................................................................. 58
F
Functional overview ............................................................................................................................ 3
Installation .......................................................................................................................................... 9
Environmental limits ..................................................................................................................... 7
Mounting dimensions ................................................................................................................... 8
Pipe-mounting ..................................................................................................................... 11, 13
Siting ........................................................................................................................................... 6
Wall-mounting ............................................................................................................................ 10
L
Logging access
Advanced security ..................................................................................................................... 23
Basic security ............................................................................................................................ 22
60 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F Index
M
ModbusTCP .................................................................................................................................... 47
Alarm groups ............................................................................................................................. 50
Alarm states .............................................................................................................................. 48
Alarm trip levels ......................................................................................................................... 52
Analog input fail states ............................................................................................................... 48
Analog inputs ............................................................................................................................ 52
Any alarm .................................................................................................................................. 50
Channel data ............................................................................................................................. 55
Channel digital signals ............................................................................................................... 51
Character set for remote operator messages ............................................................................. 56
Commands ............................................................................................................................... 47
Exception responses ................................................................................................................. 47
Modbus inputs .......................................................................................................................... 54
Operator messages ................................................................................................................... 49
Real time alarms ........................................................................................................................ 51
Remote operator messages ................................................................................................ 49, 56
Totalizer digital signals ............................................................................................................... 50
Totalizer totals ........................................................................................................................... 53
O
On-line help ..................................................................................................................................... 19
Operator displays ............................................................................................................................. 21
P
Panel-mounting ................................................................................................................................. 9
Password entry ................................................................................................................................ 24
R
Relays .............................................................................................................................................. 18
S
Setting the security switch ............................................................................................................... 28
Signal sources ................................................................................................................................. 45
Storage capacity
External ..................................................................................................................................... 57
Internal ...................................................................................................................................... 57
T
Totalizer units ................................................................................................................................... 59
IM/SM500F Issue 10.1
61
Field Mountable Videographic Recorder
SM500F
Notes
Notes
62 IM/SM500F Issue 10.1
Field Mountable Videographic Recorder
SM500F Notes
IM/SM500F Issue 10.1
63
Field Mountable Videographic Recorder
SM500F Notes
64 IM/SM500F Issue 10.1
PRODUCTS & CUSTOMER SUPPORT
Products
Automation Systems
• for the following industries:
– Chemical & Pharmaceutical
– Food & Beverage
– Manufacturing
– Metals and Minerals
– Oil, Gas & Petrochemical
– Pulp and Paper
Drives and Motors
• AC and DC Drives, AC and DC Machines, AC
Motors to 1kV
• Drive Systems
• Force Measurement
• Servo Drives
Controllers & Recorders
• Single and Multi-loop Controllers
• Circular Chart and Strip Chart Recorders
• Paperless Recorders
• Process Indicators
Flexible Automation
• Industrial Robots and Robot Systems
Flow Measurement
• Electromagnetic Flowmeters
• Mass Flowmeters
• Turbine Flowmeters
• Wedge Flow Elements
Marine Systems & Turbochargers
• Electrical Systems
• Marine Equipment
• Offshore Retrofit and Refurbishment
Process Analytics
• Process Gas Analysis
• Systems Integration
Transmitters
• Pressure
• Temperature
• Level
• Interface Modules
Valves, Actuators and Positioners
• Control Valves
• Actuators
• Positioners
Water, Gas & Industrial Analytics
Instrumentation
• pH, Conductivity and Dissolved Oxygen
Transmitters and Sensors
• Ammonia, Nitrate, Phosphate, Silica, Sodium,
Chloride, Fluoride, Dissolved Oxygen and
Hydrazine Analyzers
• Zirconia Oxygen Analyzers, Katharometers,
Hydrogen Purity and Purge-gas Monitors, Thermal
Conductivity
Customer Support
We provide a comprehensive after sales service via a
Worldwide Service Organization. Contact one of the following offices for details on your nearest Service and
Repair Centre.
UK
ABB Limited
Tel: +44 (0)1480 475321
Fax: +44 (0)1480 217948
USA
ABB Inc.
Tel: +1 215 674 6000
Fax: +1 215 674 7183
Client Warranty
Prior to installation, the equipment referred to in this manual must be stored in a clean, dry environment, in accordance with the Company's published specification.
Periodic checks must be made on the equipment's condition. In the event of a failure under warranty, the following documentation must be provided as substantiation:
1.
A listing evidencing process operation and alarm logs at time of failure.
2.
Copies of all storage, installation, operating and maintenance records relating to the alleged faulty unit.
Modbus is a registered trademark of the Modbus-IDA organization
Microsoft is a registered trademark of Microsoft Corporation in the United States and/or other countries
ABB has Sales & Customer Support expertise
in over 100 countries worldwide www.abb.com
The Company's policy is one of continuous product
improvement and the right is reserved to modify the
information contained herein without notice.
Printed in UK (05.10)
© ABB 2010
ABB Limited
Howard Road, St. Neots
Cambridgeshire
PE19 8EU
UK
Tel: +44 (0)1480 475321
Fax: +44 (0)1480 217948
ABB Inc.
125 E. County Line Road
Warminster
PA 18974
USA
Tel: +1 215 674 6000
Fax: +1 215 674 7183

Public link updated
The public link to your chat has been updated.
Advertisement