Advertisement
Advertisement
User manual
Page
3 What’s included?
4 Overview
6 Registering
7 Start Up
System Requirements and Downloading
10 Downloading the AURA™ Camera Database
11 Installing Snooper
12 Power Connection & Charging
13 Charging the internal battery
Powering Snooper using the built-in battery
Contents
14 My Speed
My Speed XL
18 Version (Hardware & Software)
19 Digital Video Recorder
22 Bluetooth
Pairing
23 Phonebook
Dialing
Call History
24 Tyre Pressure Monitoring System (TPMS)
25 Selecting vehicle type
26 Pairing the Sensors
27 Installing 116 PSI sensors
30 Bluetooth Interface Installation
31 Settings
35 Troubleshooting Snooper Downloads
38 Specification 5 Series with DVR
40 Service Under Warranty
41 Accessories
2 • EN MySpeed DVR V1.0 GB 08/17
What’s included?
1 x Snooper satellite navigation system
1 x Micro-SD Card
1 x Windscreen Mounting Bracket
1 x In-car Charger with TMC module
1 x USB Cable
1 x CD ROM
1 x Mounting disc for dash mounting the bracket
1 x Additional Micro SD card for DVR
PLEASE NOTE
Due to our desire to continually improve our products, the specification may change without notice.
Return to contents
3 • EN MySpeed DVR V1.0 GB 08/17
Overview
Front View
1 8
2
4
5
6
7
3
1. Power Button
Press and hold to switch on or off.
2. LED Power indicator
Status LED
On and Charging - Red LED
Off and Charging - Red LED
On and using internal battery - Green LED
Fully charged - No LED
3 Touch screen LCD
4. Earphone jack (Earphones not included)
5. Micro-SD Card Slot
6. TMC/Video In socket ** TMC not used on MySpeed DVR
7. USB Socket
8. DVR Menu access
** Video In The video-in connection is for connecting a rear view or reversing camera (not supplied) to the unit. The socket on the device is a 2.5mm jack.
The unit will automatically switch the screen image to show the image from the rear camera once the device receives a video signal from the rear camera - please refer to the camera fitting/wiring instructions for details on connecting the camera to the vehicle.
Rear view cameras are designed as a guide only and drivers should still be aware of their surroundings and take care when reversing.
Return to contents
4 • EN MySpeed DVR V1.0 GB 08/17
Overview
My Speed DVR Rear View
9
10
11
9. MicroSD Card Slot**
10. Speaker
11. DVR HD camera lens
MicroSD for DVR
The microSD card is highly sensitive and can become defective due to changes in external environment or severe impact. Protect the card against impact and damage. Snooper will not be held responsible in the event of microSD card damage due to user negligence or external factors.
Specification for DVR MicroSD
Capacity up to 32GB
Speed Class 6 or above and support HD and SDHC
Estimated recording time 4GB: 1 to 1.5hrs 8GB: 1.5 to 3hrs 16GB: 3 to 5hrs 32GB: 5 to 10hrs
** The 1st time the My Speed DVR is used the DVR SD card will require formatting. Refer to page 73 for instruction on how to format the card OR If a MicroSD card which was not supplied is going to be used it MUST be formatted using the Snooper player
BEFORE being used.
Return to contents
5 • EN MySpeed DVR V1.0 GB 08/17
Registering
IMPORTANT!
PLEASE READ BEFORE USING.
To enable to locate Fixed Speed Cameras and Accident Black spots you will have to register and download the AURA™ Camera
Database.
Register Online
Go to the official website www.snooperneo.co.uk and register your unit online. Your unit should normally be activated within 30 minutes of registration.
Please Note: To register, you will need the serial number of your unit which can be found on the back of the device.
Monthly Debit or Credit Card payment of £2.99 inc VAT*
Quarterly Debit or Credit Card payment of £7.99 inc VAT*
Annual Debit or Credit Card payment of £29.99 inc VAT*
*Minimum subscription term of 12 months.
** Prices subject to change.
PLEASE NOTE
Due to our desire to continually improve our products, the specification may change without notice.
Return to contents
6 • EN MySpeed DVR V1.0 GB 08/17
Start Up
Switch on the device by pressing and holding the standby power button located on the top of the unit for 2 seconds. The Snooper will automatically synchronise with the Micro-SD Card. Once the synchronisation is completed, the Micro-SD Card will not function with any other device. Snooper is now ready to operate and the camera database can be downloaded if necessary. NOTE: In most cases the Micro-SD card is already installed in the device.
Please note that if the unit does not activate when you press and hold the standby power button for 2 seconds it may require charging. Refer to the section ‘Charging the internal battery’ later in this manual.
System Requirements and Downloading
Before you can begin to download the AURA™ database onto Snooper, you will need to install the Snooper Updater software provided on the software CD.
In order for the software to be installed successfully, there are certain minimum hardware and software requirements needed.
Minimum Hardware Requirements
The computer must have an Intel Pentium Class processor or equivalent, a minimum of 32MB of RAM, a monitor with 256 (8-bit) colours or greater, a CD ROM drive, 20MB of free disc space and a spare USB connection.
Minimum Software Requirements
The software will only operate on the following Windows based operating systems:
Windows Vista
Windows 7, 8 and 8.1 and Windows 10
Mac iOS X - Yosemite, El Capitain and Sierra
Download software for Mac from: http://www.snooperneo.co.uk/SoftwareMac.cfm
NOTE: Snooper Updater software does not support Windows 95, 98, Millennium, 2000, XP.
Software Installation Instructions
Place the Software CD into a CD ROM or DVD drive. The CD should auto run and launch the Snooper menu.
To launch the CD manually: Click on ‘Start’ and then ‘Run’. In the dialogue box that opens click on ‘Browse’ – another dialogue box will open. Locate your CD ROM or DVD drive (drive letter is normally D) using the ‘Look in’ option and select ‘Snooper’ from the lower portion of the dialogue box. Once you have selected ‘Snooper’ click on ‘Open’ on the explorer box and then ‘OK’ on the Run dialogue box.
Any updates to the speed camera updater software can be obtained from www.snooperneo.co.uk/software.cfm.
If you have any problems using this software please call 0333 240 1000 during office hours and select Option 3.
Once the software is installed, you are ready to download the speed camera database onto Snooper. Once the initial setup is completed the speed camera updater software icon is displayed on your desktop.
Return to contents
7 • EN MySpeed DVR V1.0 GB 08/17
Downloading the AURA™ Camera Database
Please Note: You must register Snooper before you can perform a download.
Performing a download is simple.
1. Power up My Speed XL by pressing and holding the power button for
2 seconds and ensure that the computer is connected to the Internet.
2. Double left click the My Speed XL Camera Updater’ icon on your desktop.
3. On the software in the top left hand corner, left click ’Menu’ and then
‘Download Settings’.
Note: When you run the program for the first time, you will be asked to select the program language and download settings based on your vehicle type and what coverage of camera alerts you require.
4. Connect the My Speed XL using the USB cable provided.
Plug the
USB cable into the USB socket on the side of the Snooper
5. The updater software will then start to run automatically and download the database files that you have selected onto your unit.
The download process is as follows:
● ●
The software will display the serial number of the Snooper and a progress bar will start to progress across the screen.
● ●
The software will then connect to our database server and then download** the speed camera database.
● ●
The Snooper will then save the data received.
● ●
The software will indicate that the download is complete and will instruct you to disconnect the Snooper from your PC. Close the camera updater program by clicking the ‘x’ situated in the top right hand corner of the updater window.
**If you have a Firewall on your computer, the Firewall software may inform you that the updater software is trying to access the internet. Please make sure that you grant/allow/permit access to the updater program through the Firewall.
Please read the messages supplied by your Firewall software carefully before choosing your option. If you do not allow the program to access the internet through the Firewall, the download process will fail.
Return to contents
8 • EN MySpeed DVR V1.0 GB 08/17
Installing
Snooper comes with a windscreen bracket so that the unit can be mounted onto your vehicles windscreen.
When installing Snooper please ensure that:
● ●
The unit, with its built in GPS antenna has a clear view of the sky.*
● ●
It is located in a position where you can easily view the LCD display without having to take your eyes too far from the road ahead and that you can reach the controls safely.
● ●
Does not interfere with the vehicles controls.
● ●
Does not jeopardise the drivers or passengers safety.
● ●
You will be able to remove the device to perform downloads.
● ●
For the optimum performance or the DVR, we recommend that the unit is placed in the centre of the windscreen (right to left) either attached to the windscreen or the dashboard facia (using the mounting disc provided) The unit must not obscure you view of the road ahead.
PLEASE NOTE: Be careful to choose a location that does not block the drivers view or where it might endanger the driver or passengers should your vehicle suddenly come to a stop or be involved in an accident.
Installing Snooper using the Windscreen Suction Cup bracket
You can mount Snooper to the inside of your vehicles windscreen using the windscreen bracket provided.
● ●
Clean the area where you wish to position the bracket thoroughly with a good quality glass cleaner. This allows a more secure seal on the windscreen.
● ●
Place the suction cup and bracket on the windscreen and push the locking lever towards the windscreen to secure the bracket.
● ●
Adjust the angle of the bracket so that when the unit is attached to it you can view the display and operate the controls safely.
● ●
Position Snooper onto the bracket, by inserting the bottom of the unit first and finally clipping the top of the bracket into the slot on the top of the unit. To remove
Snooper, simply unclip the unit by pushing the top of the bracket and taking the unit from the holder.
● ●
Snooper can be powered directly either from the internal battery if it is fully charged or powered from the cigarette lighter socket. To use the cigarette lighter socket, plug the USB connector on one end of the power cable into the USB socket on the side of Snooper and plug the larger plug into the cigarette lighter socket of your vehicle.
Locking lever
Bracket adjusters
Please Note: Only use the cigarette lighter power cable provided with Snooper. Snooper operates on 5V and using any other cigarette lighter power cable will damage your device and void the warranty.
Return to contents
9 • EN MySpeed DVR V1.0 GB 08/17
Installing Snooper using the Dash Mounting Disk
If you prefer not to attach your MySpeed device to the windscreen, Snooper provides a dashboard mounting disc to fix you Snooper suction cup mount to your dashboard instead.
Instructions:
● ●
Clean the area where you want to install the disc on the vehicle’s dashboard with a damp cloth, then dry the dashboard.
● ●
Peel the paper backing away from the permanent mounting adhesive located on the disc bottom.
● ●
Press the disk onto the dashboard in the desired location, then set the GPS suction cup mount on top of the disk. Press the suction cup mount’s lever down, in the direction of the disk. This locks the Snooper in to place.
Note: Take care when attaching the disc. This type of bracket is not intended to be moved from vehicle to vehicle and is classed as a permanent fixing.
THE USE OF THE DASH MOUNT DISC IS NOT RECOMMENDED FOR LEATHER DASHBOARDS.
Power Connection & Charging
Powering and charging Snooper from the cigarette lighter socket
Snooper comes with a power cable designed to plug into your vehicles cigarette lighter socket. The power cable is suitable for both
12v DC and 24v DC vehicles. This lead will power the device but will also charge Snooper’s internal battery.
1. Plug the smaller end of the lead into the USB socket on the side of Snooper
2. Plug the other end of the cigarette lighter adaptor into your vehicles cigarette lighter socket.
If Snooper is powered using the cigarette lighter socket a LED will illuminate on the left hand side of the unit. When the battery is fully charged, the Red LED will switch off.
3. Press and hold the standby power switch on the top of Snooper for two seconds to switch the device ON.
Please Note: Do not leave Snooper plugged into the cigarette lighter socket when you start your vehicle. The cigarette lighter socket is prone to power surges as the vehicle is started and this may cause damage to your unit.
If Snooper does not power up please check that the cigarette lighter socket is clean of any debris, remembering not to insert metal objects into the socket. Check that the cigarette lighter adaptor is inserted all the way into the socket and check that the fuse in the cigarette lighter adaptor is operational. If Snooper will still not power up, please check that the cigarette lighter in your vehicle is functioning correctly.
Replacing the Fuse
If Snooper stops operating, the fuse in the cigarette lighter plug may have blown . If it has blown, follow these steps and replace it with a 3 amp, 5mm x 20mm fast acting fuse.
Caution: Using a fuse that does not meet these ratings or defeating fuse protection can damage your unit, the power cable, or the vehicles electrical system.
1. Grasp the ring near the tip of the cigarette lighter plug, and then carefully unscrew the ring by turning it counter clockwise.
Caution: If you must use pliers to loosen the ring, be careful not to crush the tip. Never use pliers or other tools to retighten the ring on the cigarette lighter plug.
2. Pull the ring straight out, then remove the metal tip and old fuse.
3. Check the fuse to see if it has blown. If it has, replace it.
4. Replace the metal tip inside the ring, then place the fuse inside the cigarette lighter plug and screw the ring back onto the plug.
Make sure the metal tip is visible when you reassemble the cigarette lighter plug.
Return to contents
10 • EN MySpeed DVR V1.0 GB 08/17
Charging the internal battery
Although Snooper can be charged using the cigarette lighter in your vehicle, an alternative method of charging via a USB socket of a PC, or USB Mains charger
(output of 5v 1000mA) - not supplied.
The battery light on Snooper will illuminate and will take approximately 3 hours to charge. When the internal battery is fully charged, the red LED will turn blue.
Note: The new battery’s full performance is only achieved after two or three complete charges and discharges.
Plug the charger cable into the USB socket on the side of the Snooper
Powering Snooper using the built-in battery
Once Snooper is fully charged, it is ready for use. Press and hold the power switch on the top of the unit for 2 seconds to switch on the device.
Note: the battery is designed to be a back up and Snooper recommends that the the MySpeed device is powered from the vehicle charger.
Aan/uit-knop
On and Charging - Red LED
Off and Charging - Red LED
On and using internal battery - Green LED
Fully charged - No LED
Return to contents
11 • EN MySpeed DVR V1.0 GB 08/17
Alerts and warnings
8
1 2 3 4 5 6 7
1
5
Direction of travel
2
Current vehicle speed
3
Road name or number
Outer ring will turn red when the vehicle speed limit exceeds the road speed limit
4
6
Distance to speed camera **
7
Type of speed camera **
8
Current time
* If the road speed limit is unknown then the speed linit will be replaced with an exclamation mark.
Road speed limit *
** Requires the AURA camera database to be downloaded to My-SpeedXL
Types of speed cameras:
SPECS or Point to Point average speed camera systems utilise state of the art video system with Automatic
Number Plate Reading (ANPR) digital technology. Each SPECS camera is features infra red illuminators fitted on gantries above the road, so they can work day or night.
SPECS speed cameras are located in multiple (at least 2 at a minimum of 200 metres apart) locations along a single stretch of road for monitoring your average speed along that particular road. So unlike other fixed speed cameras which capture your speed at a certain point in the road, SPECS average speed camera work and track you speed over a set distance, which may be several miles.
Fixed speed cameras such as Gatso, Truvello, DS2, Watchman, Peak and Speedcurb
Mobile speed cameras - usually laser. Typical uses of laser include motorway bridges, ‘road safety enforcement camera van’s ‘at the side of the road with the back doors facing you or open, tripod mounted or handheld.
Variable speed cameras appear and are used on many motorways in the UK Unlike other fixed cameras and average speed cameras, variable speed cameras don’t tend to enforce the road speed limit 24/7, but are used when the motorway’s national speed limit, normally 70mph, is temporarily lowered e.g. 60mph or 50mph. These temporary speed limits are set and changed. Speed cameras are sited on overhead gantries above each lane of moving traffic, meaning gantries can have up to four or five individual speed cameras targeting each lane of the motorway.
To mute an alert press anywhere on the screen during the camear alert, a mute symbol will appear on the top left hand side of the screen. This mute is temporary and the unit will revert back to its normal state at the next camera alert.
Return to contents
12 • EN MySpeed DVR V1.0 GB 08/17
1.0 Main Menu
1.1 Brightness Control
Snooper brightness can be adjusted using this function within the menu. To adjust the volume:
● ●
● ●
Press the ‘Brightness Control’ icon.
There are 3 settings: Auto, Day and Night.
Auto brightness
If ‘Auto’ is selected the device will automatically switch between the Day and
Night brightness setting. The time the device switches is pre-determined and cannot be adjusted. This is the default setting.
Day
If you select ‘Day’ you can adjust the day time brightness of the LCD screen.
To adjust the daytime brightness:
● ●
● ●
● ●
Press ’Day’.
Adjust the screen brightness using the and buttons.
To save the setting press OK.
Night
If you select ‘Night ‘ you can adjust the night time brightness of the LCD screen.
To adjust the night brightness:
● ●
Press ’ Night’.
● ●
Adjust the screen brightness using the and buttons.
To save the setting press OK.
Once you have adjusted both ‘Day’ and ‘Night’ brightness you should select ‘Auto’ then OK to save the setting.
If Auto is not selected then the screen will not switch between day and night automatically.
Return to contents
13 • EN MySpeed DVR V1.0 GB 08/17
1.2 Volume Control
Snooper volume can be adjusted using this function within the menu.
To adjust the volume:
●
●
●
●
●
●
Press the ‘Volume Control’ icon.
To increase the volume press the icon.
To decrease the volume press the icon.
To test the volume before saving, press the icon.
To reset the volume to the factory default press the
Press ‘OK’ at the bottom of the screen to save your setting.
icon.
1.3 Language
Snooper comes with a choice of voice prompts and alerts in several languages.
Changing the language also changes the language of the menu items as well on the unit. To use this facility:
●
●
●
●
●
Press the centre of the screen to enter the menu.
Press the ‘Change Language’ icon.
Using the up and down arrows search for the voice you require.
If you would like to listen to a sample of any voices simply press the ‘Test’ button.
Press ‘OK’ to save your setting.
1.4 Vehicle type
The speed limit of nearly every road across Europe can now be clearly displayed on your Snooper at all times.
To select the correct speed limits for your vehicle type:
Car - Advisory speed limits for a vehicle will be displayed
Caravan - Advisory speed limits for a vehicle towing a caravan will be displayed
Motorhome - Advisory speed limits for motor homes will be displayed
Truck 3.5t - 7.5t - Advisory speed limits for vehicles from 3.5T to 7.5T will be displayed
Truck 7.5t - 12t - Advisory speed limits for vehicles from 7.5T to 12T will be displayed
Truck > 12t - Advisory speed limits for vehicles greater than 12T will be displayed
Select the option you require by pressing the radio button next to the vehicle type. Press ‘OK’ to save the setting.
WARNING: These are advisory speed limits and are subject to change.
It is the responsibility of the driver to check the road side speed limit signs and abide by local driving regulations.
1.4.1 Over speed
It is possible for My Speed to alert the driver, via an audible warning, that they have exceeded the speed limit. To set the over speed warning:
Press the to increase or decrease the over speed warning
Press OK to save.
Return to contents
14 • EN MySpeed DVR V1.0 GB 08/17
1.5 Settings
The ‘Settings’ function allows you to customise the visual information provided by the MySpeed screen. To alter any of these settings:
● ●
● ●
Press the ‘Settings’ icon where you will see the list of options below.
Select the option you wish to change on the left.
There are number of different pieces of information that you can have displayed on the MySpeed screen at any one time as follows:
Note: Text or settings highlighted in Orange are the current options selected.
1.5.1 Time
Use this to change the time format for the clock on the main screen - Select 12H or 24 H
1.5.2 MPH/KMH
This option allows you to switch the information on Snooper between imperial and metric measurement.
1.5.3 Alert sound
If set to Yes a sound will be emitted if the vehicle exceeds the over sped limit (set in section 1.4.1)
Beep tone
Choose between a hard and soft beep tone for the alert sound
1.5.4 Touch Tone
You can choose between the following options:
Yes: The unit emits a confirmation tone each time the screen is touched.
No: This will turn off the confirmation beep when the screen is touched.
1.5.5 Mute
These functions are only applicable if the Aura speed camera database has been downloaded to the MySpeedXL
Smart Mute
When this mode is switched Off your unit will alert you via your chosen audible alert as well as visual alerts of fixed cameras on both sides of the road.
When this mode is switched On your unit will alert you via your chosen audible alert as well as visual alerts of fixed cameras on yourside of the carriageway only. The unit will not indicate the presence of cameras or monitoring vehicles on the opposite side
1.5.6 Auto Mute
On: If you are travelling below the posted speed limit the unit will not provide an audible alert only a visual one .
As the unit counts down the distance to the Fixed Speed Safety Camera the alert is visual only. If you are travelling above the posted speed limit however you will receive both an audible and a visual alert as normal. Once you drop below the posted speed limit for that Fixed Speed Safety Camera the audible alert will cease and the unit will only provide a visual alert.
Off: Irrespective of the vehicle speed or speed limit the unit will emit an audible warning whne a speed camera is encountered.
Return to contents
15 • EN MySpeed DVR V1.0 GB 08/17
5.15 Version
This option allows you to view the hardware and software version numbers of your unit. To view this information:
●
●
●
●
Press the centre of the screen to enter the menu.
Press the ‘Configure’ button.
Press the arrow twice.
Press the ‘Version icon.
The following screen will be displayed.
Displays the hardware version
Displays the current software version
Displays the current map version
Displays the date the AURA™ camera database was last downloaded*.
Displays the unit serial number
Return to contents
16 • EN MySpeed DVR V1.0 GB 08/17
5.17 Digital Video Recorder
The My Speed DVR will automatically record the view in front of your vehicle and will record all audio within range of the built-in microphone using the integral high definition camera and recording software which can record continuously.
The built in GPS antenna will automatically record your journey and all video, audio and trip information can be reviewed later using the Snooper Player software included on the Micro-SD card.
To enter the DVR menu:
● ●
Press the centre of the screen to enter the ‘to’ menu.
● ●
● ●
● ●
Press the ‘Configure’ button.
Press the arrow twice.
Press the ‘DVR’ icon.
3
4
5
1 2
Options in the DVR menu
Key:
1. Lock button.
Press this to manual lock the DVR video file.
NOTE:A locked file can not be overwritten by the DVR and it can only be deleted by either the DVR PC viewer Or by Formatting the
MicroSD card
2. Playback
Press this button to playback stored images or video files. Use button (1) to choose between video and still image files. Use the navigation buttons (3) to scroll through images of video files. To play video files press OK (3).
6
7
1. Save settings.
2. Return to prevoius screen.
3. Switches audio recording On or Off.
4. Changes frame rate - we recommend that is not changed
5. Adjust the sensitivity of the shock (G) sensor.
6. Switch auto record On or Off, if set to ON the DVR will start to record once the unit is switched On.
7. This will reformat the DVR MicroSD card. CAUTION this will erase ALL of the data from the DVR
MicroSD card
NOTE: Images and video footage can also be viewed on a PC, refer to the section PC Viewer for more details.
To exit playback mode press the playback button (2) again.
3. Navigation buttons and OK button - use the up, down, right and left arrows to scroll through stored files. To view files press OK.
4. Main screen. For full screen press anywhere on the main screen and to return to ‘menu view press’ the screen again .
5. Displays the status of the DVR.
6. Displays the date and time
7. Displays the microphone status On or Off (off is shown as a microphone with a line through it).
8. Returns you to the MySpeed menu*.
*If DVR View has NOT been launched from quick launch (see below). If not these buttons will return you to the DVR configure screen.
9. Press to enter the DVR setting menu
Return to contents
17 • EN MySpeed DVR V1.0 GB 08/17
Quick launch menu
To access the DVR view screen without entering the configure menu (as described above) press the button on top of the device next to the power button.
PC Viewer
Reviewing video and audio recordings using the Snooper Player.
1. Carefully remove the Micro-SD card from the device and insert it in to a
USB socket on your PC using an appropriate micro SD card reader.
2. A pop-up window should appear on your PC (see right)
If the pop up window does not appear click ‘Start’ then ‘Computer’. Look for ‘Devices with removable storage’.
The drive containing the Micro-SD card should be in this area.
3. Click on ‘Open folder to view files’.
4. Double click on the ‘Snooper Player’ icon to launch the player.
NOTE: this is NOT an installer and software will not be installed on to your PC .
5. The Snooper player screen will be displayed on your computer screen:
User Tip: if the following pop-up box appears, click ‘Continue without scanning’. Any ‘broken’ files on the SD card can be repaired using the
Snooper Player software. Clicking ‘Scan and fix (recommended)’ may result in files being deleted and data permanently lost.
Return to contents
18 • EN MySpeed DVR V1.0 GB 08/17
Snooper Player Explained
1. Click to take a snap shot from any section of video recorded.
2. Save route data. Select a folder to export it from the Snooper Player and save it to your PC.
3. Delete routes recorded and no longer required, from the Snooper Player.
4. Change settings such as Language and set up a password to protect your data (refer to setting section).
5. View video footage in ‘slow motion’.
6. Stop video footage playing.
7. Play/pause video footage.
8. Increase speed of video footage.
9. Adjust volume of audio.
10. Run video footage on repeat.
11. Rotates video footage 180 degrees.
12. Export GPS coordinates to your PC in KML format.
13. Hides or displays Google Map view window.
14. Hides or displays G-sensor information.
15. Repairs broken files.
16. Unlock ‘Incident/Event’ video footage.
1
24
25
2 3 4
18 19
20
5 6 7 8 9
21 22
26
10 11 12 13 14
23
15 16 17
17. Adjust Brightness, Contrast and Saturation of the displayed video.
18. GPS Coordinates.
19. Your speed reading. Click to switch between mph and km/h.
20. Video footage.
21. Compass heading.
22. Adjust size of Snooper Player window.
23. Google Map view. Shows route track using coordinates collected and saved by MySpeed DVR antenna.
24. G-sensor information window. Displays any event information such as hard breaking, impacts or sharp turns that might indicate that an incident has occurred on a recorded route.
25. Main route folders listing.
26. Sub route files listing.
Settings
1
4
Click on button 5 to access the settings options:
2
5
8 9 10
7
6
1. Change the path to Micro-SD card.
2. Formats the Micro-SD card - this will remove all data from the card.
3
11
12
NOTE: if a MicroSD card which was not supplied with the MySpeed DVR then it MUST be formatted using this software BEFORE it is used in the device. We also recommend that all SD cards used for the DVR should be formatted every
6-8 weeks.
3. Firmware upload> If new firmware for the DVR should be released, click on this button and follow the on screen instructions.
Check on the Snooper website for available updates: www.snooperneo.co.uk
4-6 Add or change a password. The password protects the DVR files from deletion by unuthourised users.
7. Saves password setting to the Micro-SD card.
8. Changes the Map.
9. If a replacement Micro-SD card is used it needs to be of a sufficient class or speed - click this button to test the card.
10. Changes the Snooper player language.
11. Apply and save any changes made to the setting menu.
12. Click to show Snooper player version number.
Return to contents
19 • EN MySpeed DVR V1.0 GB 08/17
10. Bluetooth
This Snooper is equipped with Bluetooth functionality. You can use it as a hands free system for a mobile phone that is equipped with Bluetooth.
●●●
Press the centre of the screen to enter the ‘to’ menu.
●●●
Press the ‘Configure’ button.
●●●
Press the ‘Bluetooth’ icon.
The phone menu screen is displayed:
Phone book - Opens the phone book.
Dial - Opens the keypad for dialing.
Disconnect - Disconnects devices
Setting - Enters the setting menu.
Search - Enters the search menu for connecting/pairing devices.
Note: some icons are greyed out as no device is currently connected
Pairing
Please ensure that Bluetooth is active and that the phone is in ‘discovery mode’
(refer to the mobile phone user guide for instructions) before starting the pairing process.
Not all mobile devices are compatible with all of the features of the Snooper
Press ‘Search’ : the following screen will be displayed.
Note: All icons are now operable as a device is connected
1.
Press ‘Search’ to discover compatible BT devices.
A list of ‘discovered’ Bluetooth devices will be shown.
Click the device you wish to pair with followed by the Connect button.
2.
Enter the 4 digit ( 4 ) PIN number on the BT device to complete the pairing process. Additional steps may be required on the BT device to compete the process (refer to the manufacturer for specific instructions).
Once pairing has completed press the return button ( 5 ).
5.
4.
Return to contents
20 • EN
3.
MySpeed DVR V1.0 GB 08/17
After the pairing is successful the Snooper will revert back to the ‘Phone Menu’ screen but the icons are no longer ‘greyed out’.
Press ( 6 ) to return to the MySpeed menu.
Phonebook ( 1 )
The contact list on the mobile phone (phonebook) can be synchronized with the
Snooper.
For Caller ID and speed dial to operate the phonebook needs to be synchronised.
To synchronise the phone book, click the button ‘Phone Book’ ( 1 ) to open the phone book interface.
Press ( 2 ) to start synchronisation.
To dial numbers from the phone book scroll through the list, using the up and down buttons, once you have found the entry you are looking for, highlight it by pressing on the name then press ‘Phone’ Icon.
1
5
2
Dialling ( 2 )
To dial a number press ‘Dialling’ then enter the number, using the keypad, press Green button ( a ) to make the call.
To end the call press button ( b ).
3 4
6 b a
2
Call History ( 3 )
Displays a list of dialled and received calls. To change the view from:
Received, Dialled or Missed numbers press button.
Use the up and own arrows to scroll through the list.
To dial any of the numbers, highlight the number and press ‘Phone’ Icon.
1. Incoming call
3. Missed Call
5. Delete highlighted number
2. Outgoing Call
4. Dial highlighted number
5. Delete ALL numbers
1
2
5
3
4
5
6
Return to contents
21 • EN MySpeed DVR V1.0 GB 08/17
10. Tyre Pressure Monitoring System (TPMS)
The Snooper Tyre Pilot application can monitor up to 22 tyres simultaneously, there are various kits and sensors available from your
Snooper dealer or from www.snooper.co.uk.
The basic starter kit you will need is either STP1800 or STP1600 (depending on the vehicle type), this kit includes a bluetooth interface which is necessary to connect the sensors to the 6 series.
To connect the interface with the 6 series open the Bluetooth menu >
Configure > Bluetooth
On the Bluetooth interface press and hold the White button (1) until the unit beeps and the
Red LED starts to flash (the TPMS interface is now in discovery mode)
In the Bluetooth menu press ‘Search ‘ to start the pairing process.
1
As the TPMS interface is discoverd it will appear in device list. To complete the pairing process select TMPS the device and press
‘Connect’ icon (1)
1
Once pairing is complete the unit will return to the main menu screen.
NOTE: The Phone book and Dial icons are greyed out as TPMS does not require these functions.
If you are pairing both TPMS and a telephone to the My Speed DVR we recommend the TPMS is paired BEFORE the telephone.
Return to contents
22 • EN MySpeed DVR V1.0 GB 08/17
10.2 Selecting vehicle type:
Snooper Tyre Pilot has been designed to be used on a range of different vehicles, including cars, caravans, motorhomes, trucks, buses, coaches and trailers and it can also monitor your spare wheel.
Tyre Pilot has been designed to monitor the following configurations:
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
Single vehicle up to 4 wheels
Single vehicle up to 10 wheels
Trailer up to 12 wheels
Spare tyre x 1
Single vehicle up to 4 wheels + spare tyre
Single vehicle up to 4 wheels + trailer up to 12 wheels
Single vehicle up to 10 wheels + spare tyre
Single vehicle up to 10 wheels + trailer up to 12 wheels
Begin by selecting your vehicle type as follows:
In the configure menu press TPMS and the following screen will be displayed:
1 2 3
1.
Bluetooth connection status - connected disconected
2.
Alert sound/Mute
3. Minimise*
4.
Exit**
5. Vehicle type
6. Configure
5
* Minimises the TPMS interface and shows the TPMS logo on the MySpeed screen
** ‘This’ this closes the TMPS menu. If the TPMS inteface is closed using the exit button you will not receive any TPMS alerts.
To receive TPMS alerts you MUST use the mimimise button.
10.3 Configure TPMS
6
4
Press ‘Settings’ (6) and the following screen will be displayed
1. Pressure units, select between BAR and Psi
2. Temperature units, select between Celsius and Fahrenheit
3.
Language. Scroll, using the arrows to change the TPMS menu language
4. Port - communication port for Bluetooth interface (fixed not adjustable)
5.
Vehicle. Change vehicle type Car, or Truck/Motorhome add Caravan or trailer
6. Setting. set the pressure and temperature tolerances
7. Pairing. Menu for pairing the pressure sensors to the TPMS app
8. Spare tyre. Show spare tyre
9. Exit setting and return to previous screen
1
2
3
4
5
6
7
8
9
NOTE: Some changes (EG Vehicle type) are not implemented on the unit until the TMPS application is closed and then reopened.
To close the application press the exit button (9) twice to return to the MySpeed menu then reopen the TPMS application by pressing the TPMS button.
Truck/Motorhome showing max number of sensors
Return to contents
Trailer/caravan showing max number of sensors
23 • EN
Spare wheel
MySpeed DVR V1.0 GB 08/17
10.4 Pairing the sensors
There are two options available for pairing sensors to the application : Input sensor ID or Radio Frequency (RF)
10.4.1 Pairing the sensors by Sensor ID
This is the simplest method as the sensor can be paired before they are fitted to the vehicle Each sensor has a unique alpha numeric code embossed on to the sensors cover, this is this the sensor ID.
1. Open TPMS menu
2. Change vehicle type (as described in section 10.3)
3. Press configure (1)
4. Press ‘Pairing’
5. Select which wheel from the image you want to program the sensor for, by pressing the image (2) six zeros should appear, which indicates a sensor has NOT been programmed to that particular wheel. If any number of letters appear than that wheel already has a sensor allocated to it.
6. Press ‘Input sensor ID’ (3)
7 Using the keypad type in the sensor ID and press the return key (4) to enter.
8. To access the trailer or spare wheel press the arrow (5)
9. Repeat steps 6 & 7 for each subsequent wheel
10. Once all of the sensors are programmed press the exit button (6) THREE times to fully exit TMPS
1
5 6
4
2
3
When the TPMS application is reopened you will see the tyre pressure readings (pressures shown here are for illustration purposes only)
To delete or edit a sensor just follow steps 1-6 then, to edit, overwrite the sensor ID with the replacement sensor ID . To delete a sensor over type the sensor ID with six zeros (this will also remove a ‘wheel’ from the image)
Press return on the keypad to save.
The same principle applies for programming sensors to trailer/caravan and/ or the spare wheel.
Refer to section 10.4.3 for details on how to install the sensors to the wheel valves.
10.4.2 Pairing the sensor by radio frequency (RF)
This method for pairing the sensor by RF is similar to the one described in section 10.4.1 with one exception, the sensor must be installed on to the tyre valve before they can be paired.
In order to correctly program each sensor with the correct wheel we recommend that each sensor is fitted and THEN programmed
BEFORE installing the next sensor. The sensors will only transmit when they are fitted to the tyre valve and can they ‘sense’ air pressure from the tyre.
Refer to section 10.4.3 for details on how to install the sensors to the wheel valves.
Return to contents
24 • EN MySpeed DVR V1.0 GB 08/17
Once the sensors are fitted follow steps 1- 6 in section 10.4.1 then:
1. Press ‘Set using valve’ button (1)
2. A pop up window will appear in the TPMS display and the button on the Bluetooth interface will flash red and the interface will ‘beep’ The interface will now search for a period of 90 seconds for a sensor which is transmitting a code. Once the code has been received, it will replace the six zeros and the interface will beep.
3. Press the return button (1) to save or the exit button (2) to cancel
4. Repeat steps 1 & 2 for each subsequent wheel
5. Once all of the sensors are programmed press the exit button (6) THREE times to fully exit TMPS
1
10.4.2 Installing 116 PSI sensors
1. Unscrew the tyre valve cap and replace with the tyre sensor.
2. Use the wrench provided to tighten the screw for added security.
User tip: Please keep the wrench in a safe place for when you next need it.
2 3
Do not over tighten to prevent possible damage to the sensor.
Hex Wrench
Do not over tighten the security screw to avoid damaging the thread on the tyre valve.
Replacing the sensor battery
1. Use the hex wrench provided to remove the anti-theft screw and remove the sensor from the tyre valve.
2. Use the battery replacement tool to unscrew the sensor cap.
screw
Return to contents
25 • EN MySpeed DVR V1.0 GB 08/17
3. Remove the old battery.
4. Replace the old battery with a new CR1632 battery cell, ensuring the positive+ is facing upwards.
CR1632
"-"
CR1632 Lithium Battery
" "
CR1632 Lithium Battery
5. Check that the water-proof rubber seal is in the correct position. Screw the sensor cap back using the battery replacement tool to tighten.
Water-proof rubber seal
Screw
Installing 188 PSI sensors.
Sensor Waterproof Rubber Seal
(Spare)
Sensor Installation Tool
The 188 PSI sensor comes in a security housing but can be installed with or without it. You can remove the security housing by simple unscrewing the casing before connecting the sensor to the appropriate tyre valve.
User tip: It is recommended to pair the sensors using the LF pairing method first before connecting the 188 PSI sensor to your tyre valve.
Before connecting the sensor to the tyre valve, shake it to ‘wake it up’. This will ensure it is ready to pair.
1. Remove the tyre valve cap and mount the corresponding sensor on the valve using the wrench provided.
Please keep the wrench for future use.
Do not over tighten the sensor cap to prevent possible damage.
Return to contents
26 • EN MySpeed DVR V1.0 GB 08/17
Installation without security housing
Replacing the sensor battery
1. Use the wrench supplied to remove the sensor.
2. Remove the anti-theft housing.
Cover
Housing
Inner Sensor
3. Use the wrench to open the sensor and gain access to the battery.
4. Remove the old battery.
Do not over tighten the sensor cap to prevent possible damage.
5. Replace the old battery with received, a new CR1632 battery cell, ensuring the positive+ is facing upwards.
"-"
CR1632 Lithium Battery
" "
CR1632 Lithium Battery
6. Check that the water-proof rubber seal is in the correct position. Screw the sensor cap back on and re-install the anti-theft housing. Follow the installation instructions above to re-install the sensor on the appropriate tyre valve.
Water-proof rubber seal
Return to contents
27 • EN MySpeed DVR V1.0 GB 08/17
10.4.5 Bluetooth Interface Installation
The Bluetooth interface should be mounted within 16 feet (5 meters) of the 6 series. It should be mounted securely with the screws provided. We would recommend that the unit is accessible for programming purposes.
The Bluetooth interface should have 12V/24v DC power when the vehicle is moving. The red cable is positive and the black wire is negative.
10.4.6 Repeater/Signal Booster Installation
Recreational Vehicles, Tow Vehicles, Trailers and Tractor Trailer *
* (If you have a Tractor Trailer that does drop and pulls of multiple trailers you need to use the STP6 section because it requires a link function)
The Repeater/Booster is designed to amplify the signal from your TPMS system sensors. In situations where length or interference prevents your monitor from receiving a signal, the Repeater/Booster increases the sensors transmitting distance.
This should not be needed to monitor distances of 53 feet or less. However, some vehicles experience difficulties due to the amount of electronic components in the engine compartment as well as where sensors are shielded by bodywork etc. causing sensor signal strength to be reduced and where extremely cold temperatures may reduce sensor battery power.
The optional signal Repeater/Booster can be ordered separately and is available at www.snooper.co.uk
The booster should be installed as low as possible on the rear of the towing vehicle or at the front of the trailed vehicle.
The hard wired booster should have 12V/24v DCC power when the vehicle is moving.
The red cable is positive and the black wire is negative.
Return to contents
28 • EN MySpeed DVR V1.0 GB 08/17
10.5 Settings
Selecting your high pressure and low pressure limits
Follow these instructions to select at which high or low pressure limits you would like your Snooper Tyre Pilot to alert.
1. Next to each axle write down what your tyre pressure is by axle and calculate what your alarm setting will be.
(you may need to consult the vehicles user guide for this information)
2. High Pressure setting will be (20% above axle tyre pressure).
3. Low Pressure setting will be (10% below axle tyre pressure).
Example: Front Axle Tyre Pressure is: 100 psi
High Pressure Alarm Setting will be: 120 psi (100 psi x 1.20 (or 20%) = 120
Low Pressure Alarm Setting will be: 90 psi (100 psi x .9 (or 90%) = 90
These are industry standards for the initial set-up, some adjustment may be needed after your first journey . Every brand of tyre operates differently, when some brands reach operating temperature the psi will increase 5 psi, other brands may increase
20 - 22 psi.
During your first journey you will see if you need to increase your High Pressure Alarm setting. For the temperature it is recommended leaving it at the factory default of 158 degree F (70 degree C).
1. In the MySpeed menu press TPMS
2. In the TPMS menu press ‘Configure’ ( For more detailed instructions on how to find ‘configure’ refer to section 10.3)
3. Press ‘Settings’ and this screen will be displayed
2
4. Adjust the upper and lower values of each axle by using the left and right arrows values as appropriate. Ignore any axles not used.
5. Once you have adjusted the upper and lower pressures for each axle, press the exit (2) to save and exit the screen.
Ensure the upper pressure value is higher than the lower pressure value and do not set the upper value higher than the upper value of the sensors you are fitting. Up to 116 PSI or 188 PSI depending on the package purchased.
To reset the value back to factory default press ‘Reset’
For the temperature it is recommended leaving it at the factory default of 158 degree F (70 degree C) .
Purchasers of this product should not solely rely on this tyre pressure monitoring system for safety and should check the condition and pressure of their vehicles tyres on a regular basis as described by the manufacturer of the vehicle or tyre manufacturer. Please note, Snooper Tyre Pilot System operates on an RF system, as with many RF tyre systems this system can occasionally suffer from interference depending on the systems location; thus causing the system to be inaccurate or not operate at all. Tyre pressures and temperatures are not the only things that can affect tyre safety; we suggest daily visual inspections and periodic checks of the vehicle tyres.
Return to contents
29 • EN MySpeed DVR V1.0 GB 08/17
If TMPS is minimized and the sensors successfully are paired with the the 6 series, it will automatically send pressure and temperature readings to the monitor every 5 minutes.
If the pressure data received by the monitor is over or under the pressure values selected, or if the tyre temperature exceeds the temperature value you have selected, the TMPS icon on the MySpeed screen will turn red and the 6 series will emit a warning beep.
To quickly access the TPMS menu press the icon on the MySpeed screen.
10.6 Minimise TPMS
1
For TPMS to operate correctly it must not be closed.
Once you have paired the sensors, configured the high and low values, of the type pressure sensors, you now need to return to the
MySpeed menu. If TPMS is closed incorrectly then you will not receive any alerts.
To return to the MySpeed menu press the ‘minimise’ button (1) .
The TPMS icon will now appear on the MySpeed screen.
10.7 Alerts
Sensors successfully paired with the Tyre Pilot display will automatically send pressure and temperature readings to the TMPS app every 5 minutes. If the pressure data received by the monitor is over or under the pressure values selected, or if the tyre temperature exceeds the temperature value you have selected, the device will provide an immediate alert.
1. The minimized TPMS icon will flash RED on the MySpeed screen
2. The device will emit an audible beep.
3. Press the TPMS icon to enter the menu
4. The corresponding icon for either pressure or temperature will appear on the display and flash.
3. The icon representing the tyre which is experiencing the issue will be shown in red .
4. To mute the alert press the speaker icon (1) .
5. Press to : Close (button 3) ,minimise (button 2) or to adjust the setting (button 4) TPMS
Examples of alerts:
1 2 3
Truck - low press on front left tyre
4
Car - low pressure on the front left tyre
Return to contents
Car high pressure on the front left tyre
30 • EN
Car - high temperature on the front left tyre
MySpeed DVR V1.0 GB 08/17
Alerts Truck, Trailer or Caravan
High pressure:
The ‘H’ denotes High pressure
Over inflated
Low pressure:
The ‘L’ denotes low pressure
Under inflated
Fast puncture :
The ‘F’ denotes Fast puncture
High temperature:
This shows that the temperature is too high.
10.8 Low battery
If the battery of the TPMS sensors is becoming discharged, the low battery warning will be displayed on the TPMS menu.
For instructions on how to replace the battery refer to page 89
Return to contents
31 • EN MySpeed DVR V1.0 GB 08/17
10.9 Combinations
Car and spare tyre
Car, trailer/caravan and spare tyre
Truck, van or motorhome and spare tyre
Truck, van, motorhome with trailer
The tyre pressures and temperatures shown in this user manual are for illustration purposes ONLY, users should consult the vehicle or tyre manufacture for the recommended settings
Return to contents
32 • EN MySpeed DVR V1.0 GB 08/17
Troubleshooting SNOOPER Downloads
If you are having any difficulty in performing a download onto the Snooper unit it is advisable to refer to the checklist in Section A first before contacting us.
If you are still unable to perform a download after following all of this checklist then please send an email to [email protected] stating the nature of your difficulty. To expedite your enquiry please supply as much detail as possible including your contact details,
Snooper serial number, PC operating system, error codes and any other relevant information. One of our technicians will reply as soon as possible.
Alternatively you can contact our Technical Helpline on 0333 240 1000 and select Option 3.
This troubleshooting guide is in two sections; Section A is in the form of a checklist that will assist you with resolving common download problems. Section B consists of a few possible reasons and possible solutions to error messages that may be displayed by the operating system or the software whilst you are trying to perform a download.
SECTION A
1. Have you registered the Snooper unit?
You will not be able to download the AURA™ database unless Snooper is registered. If the unit has not been registered, a message will appear on the software informing you that the device is not enabled. Please register online at www.snooperneo.co.uk.
2. What operating system are you using on your computer?
Snooper download software will only work on the following Windows operating systems:
Windows Vista, Windows 7, Windows 8 and Windows 10.
The software will not work on Windows 95, 98, 98SE, Millennium, Windows 2000 and Windows XP; Apple Macintosh operating systems are not supported. Windows XP (64bit) systems is not supported.
To determine which operating system you have on your computer:
Right click on the ‘Computer’ icon on your desktop and select ‘Properties’ from the drop down menu.
When the ‘System Properties’ dialogue box opens, the ‘General’ tab is selected by default. Under the heading of ‘System’ the operating system is displayed.
If you do not have a ‘My Computer’ icon on your desktop you can find this information by going to the ‘Control Panel’ and double left clicking the ‘System’ icon. The ‘System Properties’ window will then be displayed as outlined in ‘b’ above.
3. Is the USB cable supplied with Snooper connected correctly?
Please make sure the USB lead has a secure connection to the PC and is fully plugged in. Ensure the smaller connector is plugged into the USB socket on the side of the unit. Only plug the USB lead into Snooper once you see the ‘Menu Screen’ after turning
Snooper ‘ON’.
Please Note: Do not use the USB cable that comes with the USB Host connection as this lead is not compatible for speed camera updates.
4. Have you installed Snooper download software onto your PC?
If you have not installed the download software you will not be able to perform a download to Snooper. Once the software is installed there will be a new icon on your desktop . The icon is similar to this
Please check to see if you have the latest version of the software by visiting http://www.snooperneo.co.uk/software.cfm
to check what software version you have, double left click Snooper icon, look at the top of the window that opens and you will see the version number in brackets.
5. Have you connected the computer to the internet?
The download software has to download a file directly from our server and this can only be done if an internet connection is present. Therefore make sure that your PC is connected to the internet by either establishing a dial up connection or signing in to your broadband internet account before you begin to download the database to Snooper.
Return to contents
33 • EN MySpeed DVR V1.0 GB 08/17
7. What version of Internet Explorer / Netscape Navigator are you using?
The software will only operate if you have Internet Explorer or Netscape Navigator 6 or above.
To check what version of Internet Explorer you have; open your browser, click on the ‘Help’ menu and select ‘About Internet
Explorer’. This should now display what version you currently have installed. If you have a version older than 6 (e.g. 4.5), open your browser, click on ‘Tools’ and select ‘Windows Update’. This will take you to the Microsoft website where you can download the latest version of internet explorer.
To check what version of Netscape Navigator you have: open the browser, click on the ‘Help’ menu and select ‘About Netscape
Navigator’.
SECTION B
This section is for supplying possible reasons and solutions to problems you may be experiencing whilst trying to down load the database to Snooper. If after completing all the checks in Section A and you are still experiencing difficulty or have received an error message please read through the following:
1. ERROR MESSAGE – ‘The device has not been enabled yet.’
Please refer to Step 1 in section A for further details.
2. ERROR MESSAGE - ‘Error 521: There was a problem connecting to the Performance Products server…’
If you get an error message as described above this normally means that there is something blocking communication between the software, most typically a firewall, and the AURA™ server. Windows Vista, 7, 8 and 10 are supplied with a built in ‘Internet
Connection Firewall’. Depending upon which firewall software you have you will need to access the firewall settings and allow access for the Snooper update software.
If you do have a Firewall on your computer Snooper Updater software may appear to stop and it is at this point that your Firewall software will inform you that Snooper Updater software is trying to access the internet. Please make sure that you grant/allow/permit access through the Firewall.
Please read the messages supplied by your Firewall software carefully before choosing your option. If you do not allow the program access to the internet through the Firewall, the download process will fail.
If no message was prompted by the firewall software uninstall and then re-install the software and perform a download again.
Warning: We do not recommend disabling your firewall software in order to perform a download to Snooper, nor can we provide advice on how to alter the settings on third party software, nor can we be held responsible for any action taken by the PC user that makes the PC more vulnerable to malicious viruses, software and computer hackers. Any changes made to the PC firewall settings are solely at the PC user’s discretion. We would recommend contacting the third party software manufacturer for further information of how to configure the firewall software.
SECTION C
Please avoid places such as between buildings, overpass and tunnels and check the signal reception in a suitable place with a good view of the sky.
When the battery is completely discharged or turning off and then on the battery switch, the initial acquisition time may be
delayed.
2. There is no screen display, even though the power is turned on.
Please connect the AC adapter and cigarette lighter adapter to the device and turn on the power switch as the battery may be
discharged.
3. The unit is automatically shut down during operation
Please check the power control setting in the Setting menu.
Return to contents
34 • EN MySpeed DVR V1.0 GB 08/17
4. Can’t hear anything from speaker or earphone
Please check the volume level.
Please check the Mute status.
For earphone, please check if the jack is inserted properly.
5. Screen is dark.
Adjust the LCD brightness from the Setting menu.
6. Can’t read the SD card
Please remember that this device supports Micro-SD type or Micro-SDHC class 6 type card with max. 32GB.
Please check if the file system is of FAT16 or FAT32.
Please check if the surface of the card is stained with dirt.
10. Can’t write on the SD card
Please check if SD card is properly inserted.
Please check if the surface of the card is dirty.
11. Touch function does not work well.
Please touch the screen accurately because it cannot be recognized if you touch the screen with fingernails only or with less
pressure.
Please perform Touch Calibration.
Note: When battery charge is low operation of the touchscreen can be affected. Please charge the battery fully and then test the screen again.
12. Can’t charge the battery
Please check if the AC adapter/cigarette lighter adapter is connected correctly.
Please check if the contact area is dirty.
If you operate the unit during USB charging, the charging may not be completed. So please turn off the unit to charge or charge the unit by using AC/cigaratte lighter adapter.
13. Can’t recognize USB cable from PC
Inserting SD card enables to recognize it as UMS and to be seen as a directory from PC. Please check the SD card insertion.
Please check if the USB cable is normal and make sure it is connected properly.
14. Can’t mount the cradle
Please remove the dust from the place you want to mount.
Please wash and dry the suction-cup in running water and try again.
Return to contents
35 • EN MySpeed DVR V1.0 GB 08/17
Dimension & Weight
CPU
Display
Memory
Connection
GPS chip
Audio
OS
Operation Temperature
SPECIFICATION 5 SERIES
136.0 x 86.7 x 13.8 mm, 175.8g
MSB2531 Cortex A7 800MHz
5’’ (800x480) capacitive touch screen
256MB DDR3 RAM
Bluetooth (A2DP, SPP, PBAP, HFP,
Auto-link)
A/V in USB 2.0
FM Receiver, TMC
Support microSD Card up to 32GB
High sensitivity GPS chipset
Integrated speaker (1.5W / 8Ω)
Windows CE 6.0
-10°C ~ 70°C
*Note: Only the SD card supplied will work with
Snooper once synchronisation of the card and the unit has been completed. Replacement cards are available from
Performance Products Limited.
Please refer to Accessories &
Price List for further details.
Recommendations for safe use of product (Snooper, Battery and other accessories)
●●●
Always treat your product with care, keep it in a clean, and dust free environment.
●●●
Warning! May explode if disposed of in fire.
●●●
Do not expose your product to liquid or moisture or humidity.
●●●
Do not expose your product to extreme high or low temperatures.
●●●
Do not expose the battery to temperatures above +60°C (+140°F).
●●●
Do not expose your product to naked flames or lit tobacco products.
●●●
Do not drop, throw or try to bend your product.
●●●
Do not paint your product.
●●●
Do not attempt to disassemble or modify your product. Only Snooper authorised personnel should perform service.
●●●
Do not place your product in the area above your cars airbag.
CHILDREN
KEEP OUT OF CHILDRENS REACH. DO NOT ALLOW CHILDREN TO PLAY WITH SNOOPER OR ITS ACCESSORIES. THEY COULD HURT
THEMSELVES OR OTHERS, OR COULD ACCIDENTALLY DAMAGE YOUR UNIT OR ACCESSORY. SNOOPER CONTAINS SMALL PARTS THAT
COULD BE DETACHED AND CREATE A CHOKING HAZARD.
Return to contents
36 • EN MySpeed DVR V1.0 GB 08/17
Battery
We recommend that you fully charge the battery before you use Snooper for the first time. A new battery or one that has not been used for a long time could have a reduced capacity the first few times it is used.
Use only Snooper approved original batteries intended for use with Snooper. We recommend that only Snooper authorised personnel replace the battery in your unit. Using other batteries and chargers could be dangerous.
Battery charge time can vary depending on different conditions such as operating temperature, application usage patterns, features selected and voice transmissions when using the Bluetooth functionality.
Disposing of the Battery
Please check with your local waste management service authority regarding regulations for the safe disposal of the battery. The battery should never be placed in municipal waste. Use a battery disposal facility if available.
Disposal of Old Electrical or Electronic Equipment
This symbol on the product indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical or electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this Snooper product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local waste authority.
Touch Screen
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
To avoid scratching the touch screen, do not use sharp tools.
Do not allow the touch screen to come into contact with other electrical devices. Electrostatic discharges can cause the touch screen to malfunction.
Do not allow the touch screen to come into contact with water. The touch screen may malfunction in humid conditions or when exposed to water.
Do not allow heavy objects to press against the LCD display. This can cause damage to the LCD screen
Do not twist the casing of the unit as this can cause damage to the LCD screen
Do not press too hard when operating the touch screen. If the touch screen is unresponsive please clean the screen with an approved cleaning solvent first and then try again. Pressing too hard on the touchscreen can cause the LCD screen to break.
Do not drop the device as this may result in damage to the LCD screen.
Do not strike the LCD screen with a pointed or sharp object. Whilst no visible damage may be observed the LCD display may be weakened and prone to crack if exposed to low and high temperatures.
PLEASE NOTE: Damage to the LCD is not covered under warranty where: willful or accidental damage has occurred. Use of the device otherwise than in accordance with the user instructions; any tampering with, or alteration of, the device is made by anyone other than us.
Return to contents
37 • EN MySpeed DVR V1.0 GB 08/17
Service Under Warranty
Snooper comes with a standard 12 month manufacturer’s warranty. Register your device for warranty at www.snooperneo.co.uk
Faulty Products up to 30 days from purchase.
Refund or Replace Policy, Contact Seller directly for this. The consumer is responsible to ensure software is up to date. All products must be complete with accessories and original packaging on return.
Faulty Products from 31 days to 12 months from purchase.
Snooper (Performance Products Ltd) will offer a prompt repair service. In all cases we reserve the right to inspect the product and verify the fault. Contact Seller for their returns procedure, all warranty claims MUST go through the seller. Consumer is responsible for software updates!
We do not cover faults caused by accident, neglect, misuse or normal wear and tear. All products must be complete with accessories and original packaging on return.
PLEASE NOTE: We cannot process any warranty claims unless proof of purchase is provided.
Please retain your receipt as a precaution.
Full terms and conditions of warranty are available on request.
Limited Warranty
This Snooper product is warranted against all defects in materials and workmanship for a period of one (1) year from the date of original purchase, when purchased from an authorized Snooper dealer.
ALL PURCHASES OF SNOOPER PRODUCTS FROM NON-AUTHORIZED SNOOPER DEALERS ARE SUBJECT TO FURTHER WARRANTY
RESTRICTIONS AS DESCRIBED BELOW.
The conditions of this Limited Warranty and the extent of responsibility of Performance Products Ltd (PPL) under this Limited
Warranty are as follows :
1. This Limited Warranty will become void if service is performed by anyone other than an approved Snooper Warranty Service Centre that results in damage to the product.
2. This Limited Warranty does not apply to any product which has been subject to misuse, neglect or accident, or which has had the serial number altered, defaced or removed, or which has been connected, installed, adjusted or repaired, other than in accordance with the instructions provided by Snooper.
3. Should you have any difficulties with the performance of this product during the warranty period, please call Snooper or visit our web site http:// www.snooperneo.co.uk. You may also contact Snooper Customer Services at the address listed below for any service help you may need with
Snooper products.
4. PROOF OF DATE OF PURCHASE FROM AN AUTHORIZED SNOOPER DEALER WILL BE REQUIRED FOR ANY WARRANTY SERVICE OF THIS PRODUCT.
5. SNOOPER PRODUCTS PURCHASED FROM A SOURCE OTHER THAN AN AUTHORIZED SNOOPER DEALER, INCLUDING ANY AND ALL PURCHASES
VIA THE INTERNET FROM A NON INTERNET AUTHORIZED SNOOPER DEALER, SHALL NOT BE COVERED BY ANY SNOOPER LIMITED WARRANTY TO
THE EXTENT ALLOWED BY APPLICABLE LAW.
6. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM EU COUNTRY TO EU
COUNTRY.
7. ALL IMPLIED WARRANTIES, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, SHALL HAVE NO GREATER DURATION THAN
THE WARRANTY PERIOD SET FORTH ABOVE. UNDER NO CIRCUMSTANCES SHALL SNOOPER BE LIABLE FOR ANY LOSS OR DAMAGE,
DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT. BECAUSE SOME EU COUNTRIES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
8. Product must be shipped in its original carton or equivalent carton, fully insured, with shipping charges prepaid. Snooper will not assume any responsibility for any loss or damage incurred in shipping.
9. The sole responsibility of Snooper under this Limited Warranty shall be limited to the repair of the product or the replacement of the product only (whichever is deemed appropriate and at the sole discretion of Snooper).
10. This Limited Warranty does not cover car static or other electrical interferences, labour costs or any other associated or incidental costs incurred for the removal or reinstallation of the unit for repair.
Return to contents
38 • EN MySpeed DVR V1.0 GB 08/17
Full Product Range & Accessories
From cables and cases to tyre pressure monitoring and dash cams, we have a full range of automotive products and accessories for all types of devices. Visit www.snooper.co.uk, call 0333 240 1000 or any authorised Snooper retailer for prices and availability.
Snooper End User License Agreement
Performance Product ltd uses the following brand names and these brand names form part of this licence agreement:
Snooper
Truckmate
Ventura
My Speed and My Speed XL
The software embedded in your Snooper product (the “Software”) is owned by Performance Products Ltd or its subsidiaries brand
(“Snooper”). The map data embedded in or accompanying your Snooper product (the “Map Data”) is owned by HERE Global
B.V(“HERE”) and is licensed to Snooper. Snooper also owns, or licenses from third party providers, information, traffic data, text, images, graphics, photographs, audio, video, images and other applications and data (“Other Content”). The Map Data and Other
Content are collectively the “Content”. Both the Software and Content are protected under copyright laws and international copyright treaties. The Software and Content are licensed, not sold. The structure, organization and code of the Software are valuable trade secrets of Snooper and/or its third-party providers. The Software and Content are provided under the following license and are subject to the following terms and conditions which are agreed to by End User (“you” or “your”), on the one hand, and Snooper and its licensors (including their licensors and suppliers) and affiliated companies on the other hand. HERE and Snooper’s other licensors, including the licensors, service providers, channel partners, suppliers and affiliated companies of HERE, Snooper and their respective licensors, are each a direct and intended third party beneficiary of this Agreement and may enforce their rights directly against you in the event of your breach of this Agreement.
IMPORTANT: CAREFULLY READ THIS LICENSE BEFORE USING THIS PRODUCT. INSTALLING, COPYING, OR OTHERWISE USING THIS
PRODUCT OR THE CONTENT INDICATES YOUR ACKNOWLEDGMENT THAT YOU HAVE READ THIS LICENSE AND AGREE TO ITS TERMS. IF
YOU DO NOT AGREE, RETURN THE COMPLETE PRODUCT WITHIN 7 DAYS OF THE DATE YOU ACQUIRED IT (IF PURCHASED NEW) FOR A
FULL REFUND TO THE DEALER FROM WHICH YOU PURCHASED THIS PRODUCT.
You, the User, acknowledge that by continuing to use of this product, that:
1. Your incorrect use of this product may cause damage/loss/endanger life/health and that of others (for example if you do not follow traffic laws and rules first and foremost, despite any instruction that the product may give you);
2. Snooper, its affiliates and its third-party suppliers, limit their liability for loss, damage, injury, consequential damages you or third parties may incur due to you not adhering to this warning and not obeying traffic rules/laws over and above any instructions of the
Product.
The User is cautioned to always observe the Road Traffic Rules, Regulations and Laws (“Traffic Rules”) in the territory the product is used in, as well as exercising responsible driving behavior while using the product. FAILURE TO DO SO MAY CAUSE SERIOUS INJURY/
DEATH. In the event of a conflict between the Traffic Rules and the product’s instructions, the Traffic Rules must always prevail.
1. LICENSE:
SNOOPER (“we” or “us”) provides you with storage media containing the Software and the embedded or accompanying Content, including any “online” or electronic documentation and printed materials (together called the “Product” for purposes of this License
Agreement), and grants you a limited, non-exclusive license to use the Product in accordance with the terms of this License
Agreement. The copyright and all other rights to the Product shall remain with us and, as applicable, our third-party Content providers. You must reproduce any copyright or other notice marked on the Product on all copies you make. You acknowledge the confidentiality of the Software and the Content. At all times during the Term and thereafter, you shall keep confidential and not disclose, directly or indirectly, and shall not use for your benefit or any other individual or entity, any Confidential Information of Snooper or HERE . You further acknowledge that use of HERE products with non-HERE maps may result in increased variance between the location displayed on the map and ground truth location. Snooper also reserves the right to discontinue offering any
Content supplied by any third party supplier if such supplier ceases to supply such content or Snooper’s contract with such supplier terminates for any reason.
Return to contents
39 • EN MySpeed DVR V1.0 GB 08/17
2. YOU MAY: a) Use the Product for solely your own internal business or personal use and not for resale, distribution, sublicense, commercial use or use in call centres. The Product may be used in a vehicle as part of a fleet tracking/routing and/or dispatch application.
b) transfer the Product to someone else only if you assign all of your rights under this License, cease all use of the Product, erase or destroy any copy (including the hard disk copy) made in support of your use of the Product, and ensure that the other person agrees to the terms of this License.
3. YOU MUST NOT: a) make copies of the Product except as expressly permitted in Section 2 of this License Agreement.
b) translate, reverse engineer, decompile, disassemble or create derivative works of the Product except to the extent the foregoing restriction is expressly prohibited by applicable law.
c) rent, lease, time-share, loan, sub-license, distribute, assign, or transfer the Product or any unlock code for the product except as set out in Section 2(c) above.
d) utilize the Product to create or assist in the creation of a digital map database (a database of geospatial data containing the following information and attributes: (x) road geometry and street names; or (y) routing attributes that enable turn-by-turn navigation on such road geometry; or (z) latitude and longitude of individual addresses and house number ranges.) e) modify the Product or merge all or any part of the Product with another program.
f) remove, obscure or alter any copyright, trademark, restrictive legend or other proprietary rights notices contained in the Product.
g) use the Product for in-flight navigation of aircraft.
h) use the Product to provide competitive information about HERE or its products to third parties.
i) use the Product or any derivative thereof for the purpose of enforcement of traffic laws including but not limited to the selection of potential locations for the installation of speed cameras, speed traps or other speed tracking devices.
4. LIFETIME MAPS:
If you purchase a Lifetime subscription (“LMU”) (sold separately) or if your Snooper product comes bundled with a LMU subscription, you will receive Map Data updates when and as such updates are made available on Snooper’s website, during the useful life of one
(1) compatible Snooper or as long as Snooper receives Map Data from HERE or other third party provider, whichever is shorter. A product’s “useful life” means the period during which the product (a) has sufficient memory capacity and other required technical capabilities to utilize current Map Data and (b) is capable of operating as intended without major repairs. A product will be deemed to be out of service and its useful life to be ended if no updates have been downloaded for such product for a period of 24 months or more. Unless otherwise stated, the updates you receive under the subscription will be updates to the same geographic area included with your Snooper product when originally purchased. In some instances, your Snooper product might not have sufficient memory remaining for you to load an update to the Map Data, in which case you will need to either (a) select reduced Map Data coverage for your updates, or (b) purchase separately a microSD card or a SD card (if and as applicable to your Snooper product) and load all of the
Map Data coverage for your updates to the card and insert the card into the microSD card or SD card slot contained in your Snooper product. If neither of the measures in (a) or (b) can be used to address your product’s lack of sufficient remaining memory, then
Snooper may conclude that the “useful life” of your product has expired. Snooper may terminate your LMU subscription at any time if you violate any of the terms of this Agreement or your subscription. Your LMU subscription may not be transferred to another person or another Snooper product.
Return to contents
40 • EN MySpeed DVR V1.0 GB 08/17
9. TERM:
This License shall continue for as long as you use the Product. However, this License will terminate automatically without notice from
SNOOPER if you fail to comply with any of its terms or conditions. You must agree, upon termination, to destroy all copies of the
Content in existence. The Limitations of Warranties and Liability set out below shall continue in force even after any termination. In addition, this Agreement shall terminate immediately upon the termination of an agreement between Snooper and any third party from whom Snooper licenses the Content. All clauses which by their nature need to continue after the termination of this Agreement such as but not limited to the Governing Law and Indemnity clauses shall remain in force despite termination of this Agreement.
10. LIMITATION OF WARRANTIES:
THE PRODUCT IS PROVIDED ON AN “AS IS” AND “WITH ALL FAULTS” BASIS. SNOOPER AND ITS LICENSORS OR SUPPLIERS,
INCLUDING HERE , EXPRESSLY DISCLAIM ALL WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, ANY EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, NONINFRINGEMENT,
SATISFACTORY QUALITY, ACCURACY, TITLE, OR ANY WARRANTY ARISING BY LAW, STATUTE, USAGE OF TRADE, OR COURSE OF
DEALING. NO ORAL OR WRITTEN ADVICE OR INFORMATION PROVIDED BY SNOOPER OR ITS SERVICE PROVIDERS, SUPPLIERS,
CHANNEL PARTNERS AND LICENSORS, INCLUDING HERE , OR BY AGENTS AND EMPLOYEES OF SNOOPER, ITS SERVICE PROVIDERS,
SUPPLIERS, CHANNEL PARTNERS OR LICENSORS, INCLUDING HERE , SHALL CREATE A WARRANTY, AND YOU ARE NOT ENTITLED TO
RELY ON ANY SUCH ADVICE OR INFORMATION. THIS DISCLAIMER OF WARRANTIES IS AN ESSENTIAL CONDITION OF THIS AGREEMENT.
Some States, Territories and Countries do not allow certain warranty exclusions, so to that extent the above exclusion may not apply to you.
11. LIMITATION OF LIABILITY:
YOU ASSUME ALL RESPONSIBILITY AND RISK FOR THE USE OF THIS PRODUCT. IT IS YOUR RESPONSIBILITY TO USE THIS PRODUCT
PRUDENTLY AND TO VISUALLY VERIFY STREETS, ROADS, ROAD SIGNS AND DIRECTIONS. THIS PRODUCT IS INTENDED TO BE USED
ONLY AS A TRAVEL AID AND SHOULD NOT BE USED FOR ANY PURPOSE REQUIRING PRECISE MEASUREMENT OF DIRECTION,
DISTANCE OR LOCATION.
SNOOPER AND ITS SUPPLIERS AND LICENSORS, INCLUDING HERE , DISCLAIM ALL LIABILITY FOR ANY LOSS, INJURY OR DAMAGE
RESULTING FROM USE OF THIS PRODUCT, WHETHER DIRECT OR INDIRECT, AND WHETHER OR NOT SNOOPER OR ANY SUCH
SUPPLIER OR LICENSOR HAS BEEN ADVISED OF OR HAS KNOWLEDGE OF THE POSSIBILITY OF SUCH LOSS, INJURY OR DAMAGE. IN
NO EVENT SHALL SNOOPER, HERE OR ANY OF THEIR RESPECTIVE SUPPLIERS OR LICENSORS HAVE ANY LIABILITY TO YOU OR ANY
OTHER PERSON OR ENTITY FOR ANY COMPENSATORY, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES
WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, LOSS OF REVENUE OR PROFIT OR COSTS OF COVER, LOST OR DAMAGED DATA,
LOSS OF USE OR BUSINESS INTERRUPTION, OR OTHER COMMERCIAL OR ECONOMIC LOSS, EVEN IF WE HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, OR THEY ARE FORESEEABLE. WE ARE ALSO NOT RESPONSIBLE FOR CLAIMS BY A THIRD PARTY.
SNOOPER’S AND ITS LICENSORS’ TOTAL AGGREGATE LIABILITY WITH RESPECT TO ITS OBLIGATIONS UNDER THIS AGREEMENT OR
OTHERWISE WITH RESPECT TO THE SNOOPER PRODUCT OR THE CONTENT SHALL NOT EXCEED $1.00. THE LIMITATIONS IN THIS
SECTION SHALL APPLY WHETHER OR NOT THE ALLEGED BREACH OR DEFAULT IS A BREACH OF A FUNDAMENTAL CONDITION OR
TERM OR A FUNDAMENTAL BREACH. NOTWITHSTANDING ANYTHING TO THE CONTRARY CONTAINED HEREIN, HERE SHALL HAVE
NO MONETARY LIABILITY TO YOU FOR ANY CAUSE (REGARDLESS OF THE FORM OF ACTION) UNDER OR RELATING TO THIS LICENSE
AGREEMENT. Some States, Territories and Countries do not allow the certain liability exclusions, or exclusion of incidental or consequential damages, so to that extent the above limitations may not apply to you.
12. GENERAL:
This License is the entire agreement between us, superseding any other agreement or discussions, oral or written, and may not be changed except by a signed agreement. This License shall be governed by and construed in accordance with the laws of the State of
Kansas, United States of America. If any provision of this License is declared by a court of competent jurisdiction to be invalid, illegal, or unenforceable, such a provision shall be severed from the License and the other provisions shall remain in full force and effect.
The covenants and obligations undertaken by the End User herein are intended for the direct benefit of HERE and may be enforced by HERE directly against the End User. HERE shall have the right to audit Snooper and End User for compliance with this License
Agreement.
Return to contents
41 • EN MySpeed DVR V1.0 GB 08/17
13. IF YOU RECEIVE SAFETY CAMERA INFORMATION:
You acknowledge that Products are designed to be used as an aid to safer driving. You can receive messages to alert you to locations of safety cameras (“AURA” ) which will enable you to monitor your speed through these areas. Snooper nor its Licensors, including
HERE , warrant that all types and locations of safety cameras are available, as cameras may be removed, relocated or new cameras installed. Neither Snooper nor its Licensors, including HERE, condone speeding or any other failure to comply with your local traffic laws. It is your responsibility to drive with the posted speed limit at all times and to drive in a careful manner. Neither Snooper nor its
Licensors, including HERE, accepts ANY liability whatsoever for you receiving any speeding fines or points on your license through using this device. Neither Snooper nor its Licensors, including HERE, guarantees the accuracy of the data contained within this database either expressed or implied. In the event you receive a fine or any other fine for speeding or contravention of any traffic law, or are involved in an accident, neither Snooper nor its Licensors, including HERE, are responsible for any damages of any type. In some countries the use of data or information regarding safety or speed cameras may conflict with local law and/or regulations. It is your responsibility to make sure that your use of the data is in compliance with local laws and/or other regulations. Usage is at your own risk.
14. HERE GLOBAL B.V BRAND ICON LICENSED PRODUCT (the “Brand Icon”)
If your Product includes the Brand Icon, you agree that the use of the Brand Icon is subject to the terms and conditions set forth in this Agreement and there may be additional third party terms, conditions and restrictions to which the use of the Brand Icon will be subject provided to you from time to time by Snooper in the release notes applicable to your Product.
15. NORWAY DATA
You are prohibited from using the data of Norway to create commercial general purpose printed or digital maps, which are similar to the basic national products of the Norwegian Mapping Authority. Any map of the data of Norway shall be regarded as similar to the basic national products of the Norwegian Mapping Authority if such map has a regional or national coverage, and at the same time has a content, scale and format that are similar to the basic national products of the Norwegian Mapping Authority.
16. PREMIUM POINTS OF INTEREST
You are expressly prohibited from using the Premium Points of Interest in Europe (a) telephone call routing related applications; (b) screen pop applications, (c) CD-ROM director of other derivative directory product; (d) verification services; (e) caller name services; and (f) online marketing lead verification services.
17. COPYRIGHT NOTICES
Data Source for Maps “© 1987 - 2017 HERE. All rights reserved HERE Global B.V
18. INTELLECTUAL PROPERTY
The Service, Content and Software are protected under international copyright laws. Snooper and HERE claims copyrights in its
Service, Content, and Software to the maximum extent of the law. Subject to the Terms, Snooper and HERE retains all right, title and interest in the Service, its Content, the Software and in all other Snooper products, software and other properties provided to you or used by you through the Service.
Return to contents
42 • EN MySpeed DVR V1.0 GB 08/17
Snooper Ventura @snooperventura Snooper UK www.snooper.co.uk
Return to contents
Performance Products Ltd, Cleaver House, Sarus Court, Manor Park, Runcorn,
Cheshire, WA7 1UL. Tel +44 (0)1928 579579 E: [email protected].
43 • EN
Advertisement