Advertisement
Advertisement
SWAN CYCLONIC UPRIGHT
INSTRUCTION MANUAL
Model: SU3017
GUARANTEE
This product is guaranteed for 2 years from the date of original purchase.
If any defect arises due to faulty materials or workmanship, the unit will, either be repaired, replaced or refunded at our discretion.
The following conditions apply:
The product must be returned to the retailer with original proof of
purchase.
The product must be installed and used in accordance with the instructions contained in this user instruction guide.
It must be used only for domestic purposes.
It does not cover wear and tear, damage, misuse or consumable parts.
The supplier has no responsibility for incidental or consequential loss or damage.
Valid in the UK & Eire only.
Valid only if purchased from the LWSD Group.
Technical Specification:
Power supply:
Power Consumption:
Model number:
Protection:
220V-240V AC. 50Hz
1600 Watts Nom, 1800W Max
SU3017
Class II
LWSD Group
L70 1AB
Box MPRC8
Swan Vacuum Helpline. Please Call 01733 404703
Swan Vacuum Spare Parts. Please Call 01733 404709
Calling from outside the UK please call - 00 44 1733 404703
1
IMPORTANT SAFETY INSTRUCTIONS
When using your Cyclonic Upright Vacuum, the following basic safety precautions should be observed:
1. Never vacuum wet surfaces, pick up wet objects or use in wet conditions.
2. Always disconnect the vacuum from the electrical supply before attempting any maintenance.
3. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
4. Do not use the vacuum to pick-up large objects that could, damage or cause a blockage.
5. Do not use the vacuum to pick up builders rubble, sand, plaster dust etc.
6. This vacuum cleaner is for domestic use only. Industrial or commercial use invalidates the warranty.
7. Do not let children use the vacuum cleaner unattended.
8. Do not use without a dust bag/bin and filter in place.
9. Use extra care when cleaning on stairs.
10. Always ensure the vacuum height setting is set in the tools position when using on stairs. Take extra care not to allow the vacuum to tilt and the beater bar make contact with the carpet whilst using the tools on the stairs.
11. Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts.
Safety Alerts:
To reduce the risk of fire, electric shock, or injury
1. Do not leave the vacuum unattended when plugged in, unplug from the outlet when not in use and before servicing.
2. To reduce the risk of electric shock, do not use outdoors or on wet surfaces.
3. Use only as described in this manual.
4. Do not use with a damaged cord or plug.
5. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces.
6. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
7. Do not handle the plug or the vacuum cleaner with wet hands.
8. Turn off all controls before unplugging.
2
Electrical Safety
Before switching on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 220 – 240V AC;
50Hz. Connection to any other power source may damage the unit.
This product may be fitted with a non – rewireable plug. If it is necessary to change the fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement obtained.
If the plug has to be changed because it is not suitable for your socket, or becomes damaged in any way, it should be cut off and an appropriate plug fitted following the wiring instructions below. This should be carried out by a qualified electrician. The plug removed must be disposed of safely, as insertion into a 13 Amp socket is likely to cause an electrical hazard.
IMPORTANT – THIS IS A CLASS II APPLIANCE AND DOES NOT REQUIRE
AN EARTH CONNECTION.
Wiring Instructions
The wires in this mains lead are colored in accordance with the following code:
Blue = Neutral Brown = Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows (refer to the plug wiring diagram). y
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured Black. y
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured Red.
If a 13Amp (BS1363) plug is used, a 13Amp (BS1362) fuse must be fitted, or if any other type of plug is used, a 13Amp fuse must be fitted, either in the plug or adaptor, or on the Distribution Board.
3
Description:
3
4
1
2
Folding Handle
Folding Handle Release Latch
Flexible Hose
Handle Release Pedal
11
12
13
14
Air Driven Turbo Brush
Carry Handle
Dust-Bin
Dust-Bin Handle
5
6
Exhaust Filter Cover
Bin Full Indicator
Quick Release Power Cord Holder
Hose Handle
15
16
17
18
Dusting Brush
Upholstery Brush
Crevice Tool 7
8
9 Telescopic Tube
10 On/off Switch
19
20
Carpet Height Adjuster
Tool Caddy
Inspection door
4
OPERATING INSTRUCTIONS
Assembling Your Vacuum Cleaner
On/off switch
The On/Off slide switch is sited on the handle
1. Carefully unpack all components and set aside the packaging.
2. Lift vacuum body to the upright position. of the vacuum
3. Swing the folding handle into the upright position
4. The handle will click
and lock in place.
(Fig. 1)
Fig 1
5. Make sure the quick release cord holder is in the upright position.
Quick Release
6. Wrap the cord into place by wrapping it in a clockwise direction around the quick release cord holder and the lower cord holder. (Fig. 2)
Fig 2
7. Turn the quick release cord holder left or right 180° to unwrap the power cord.
(Fig. 2)
How to Start
The upright vacuum can be used on multiple types of carpeting, bare floors or upholstery with attachments. When using the attachment tools such as the crevice tool and the upholstery brush, place the handle of the vacuum in the upright position and set the carpet height selector to the tools setting.
1. Turn the quick release cord holder to either side 180° to release the power cord.
2. Plug the power cord into an electrical outlet socket.
3. Depress on the handle release pedal to lower the handle.
4. Slide the On/Off button to the “ON” position to switch on the vacuum. When using the attachments, the vacuum must be in the upright position. (Fig. 3)
Fig 3
5
OPERATING INSTRUCTIONS
Carpet Height Adjustment
This upright vacuum can be used on multiple types of carpet, bare floors and upholstery with attachments.
To select a carpet height setting:
1. Turn the vacuum cleaner "Off".
2. Select your carpet height setting by turning the height adjustment knob to the setting you desire. (Fig.4 )
Fig. 4
Fig. 7
Using and Storing the
Accessories
The vacuum is designed with a built-on tool caddy for the accessories.
1. On the side of the vacuum is a storage space for the upholstery brush, crevice tool, dusting brush and telescopic tube. (Fig. 7)
Suggested Pile Height Settings:
You may need to raise the height of the vacuum to make some jobs easier, such as scatter rugs and longer pile carpets.
Suggested settings are:
5
3
MED: medium pile.
1
HIGH: shag carpet, long pile,
plus scatter rugs and tools. very low pile, bare floors.
Caution: Do not use the upholstery brush on delicate or woven fabrics that may snag on the upholstery brush.
Do Not use the upholstery brush on wooden floors as this accessory might cause mild scratching.
Attaching the Telescopic Tube to the
Hose
1. Attach the flexible hose to the hose handle by pushing on and twisting to lock. Push the hose handle onto the telescopic tube.
(Fig. 5)
To extend the telescopic tube, simply push forward on the plastic button and pull the inner tube outward to extend for a longer reach.
(Fig. 6)
Fig. 5 Fig. 6
Using the Attachments
Warning: To reduce the risk of electric shock, the power cord must be disconnected before attaching or removing accessories. a) Place the vacuum in its upright position. Make sure the vacuum cleaner is NOT plugged into the electrical outlet when adding or removing accessories. b) Make sure the carpet height selector is set to the “Tools” position (Fig.8)
Tools
Fig. 8
6
OPERATING INSTRUCTIONS c) Remove the hose connector from the side of the unit and attach the hose handle. (Fig.
9) d) If additional length is required, attach the hose handle to the telescopic tube and then attach the desired accessory.
Fig.9
Using the Air Driven Turbo Brush
1. Pull out the air driven turbo brush from the storage compartment. (Fig. 10)
Fig. 10
1. Connect the air driven turbo brush to the hose handle or telescopic tube.
Dusting Brush
The dusting brush is used for furniture.
Crevice Tool
For radiators, crevices, corners, baseboards and between cushions.
Upholstery Tool
The upholstery tool is ideal for use on furniture.
The unique surface makes it an excellent tool for removing unwanted pet hair.
NOTE: This tool is not a grooming tool and should not be used on animals.
Caution:
Do not use the upholstery tool on delicate or woven fabrics that may snag on the upholstery brush.
Do Not use the upholstery tool on wooden floors as this accessory might cause mild scratching.
Do NOT over extend the hose length when reaching. Doing so may cause the vacuum to tip over.
Warning: Avoid tilting the vacuum on carpeted stairs whilst using the hose with attachments. The agitator will continue to rotate whilst using the attachments.
Avoid leaving the vacuum in one place for an extended period of time, particularly on thick carpet.
The efficiency of your Air Driven Turbo
Brush depends on the bristle brush rotating at high speed. Strong air suction is needed to accomplish this. In order to ensure maximum air suction is maintained, please read the following instructions: a) Empty the Dust-Bin frequently during use. b) Always “TapClean” the HEPA dust-bin filter each time the dust-bin is emptied. c) Ensure the rotating bristle brush is kept free of hair and string. d) Inspect the turbine regularly to ensure the air passage is free of dirt and debris.
Cleaning Air Driven Turbo Brush
Fig. 11 Fig. 12 a) Pull the locking latch upwards to open
the inspection door of the Turbo brush.
(Fig 11). b) The door housing is hinged and will tilt up
approximately 45 º only.
(Fig. 12)
7
OPERATING INSTRUCTIONS
Cleaning Air Driven Turbo Brush cont. c) Inspect the turbine wheel and air passage for debris and blockages. Remove debris if present. d) Inspect the rotating brush for built-up hair or string. If present, remove carefully by cutting with scissors. Avoid damaging or cutting bristles. e) Once clean, close the inspection door.
Bin Full Indicator
When the bin full indicator lights, either the dust-bin is full, the HEPA filter requires cleaning or there is a blockage in the hose or telescopic tube. You must check and empty the dust-bin, clean the HEPA filter and debris screen also, check the unit for any blockages in the hose and tubes. Check behind inspection door see page 4.
Fig. 13 Bin full indicator
Removing & Emptying the Dust-Bin
The “Dust-Bin” must be emptied when the dirt level is "FULL“, or if the bin full indicator has lit. To remove the dust-bin from the vacuum follow steps 1 and 2:
1. To remove the dust-bin, lift the dust-bin release handle then pull the dust-bin out from the vacuum.
(Fig. 14)
Fig. 14 hold it by the handle and over a garbage can and press the trap door release button to empty. (Fig. 15)
Fig. 15
2. To empty the dust-bin,
Cleaning the Dust-Bin
The dust-bin can be washed in lukewarm water. Do not use strong detergents. Ensure that the dust-bin is fully dry before replacing in the vacuum cleaner. (Fig. 16)
Fig. 16
Do not wash in dishwasher.
Cleaning the HEPA Dust-Bin Filter
IMPORTANT, Please Note:
The rinseable “TapClean” HEPA Dust-BIN
Filter will stop most dust particles and airborne allergens from re-entering the air you breathe.
In fact it stops 99.97% of all particles as small as 0.3 microns - many times smaller than a human hair.
Because of this the HEPA Filter will quickly accumulate many fine dust particles inside the white filter folds that will eventually block or reduce the vacuum suction power – if not cleaned properly.
Clean the HEPA Filter after each use as described in this section.
To remove the HEPA filter, hold the dust cup container by the handle and turn the cover anti-clockwise to unlock the dust-bin container lid. (Fig. 17)
1. To remove the HEPA
filter from the dust cup.
Fig. 17
Turn over the dust-bin lid and twist the HEPA filter anti-clockwise to unlock. (Fig. 18)
Fig. 18
8
OPERATING INSTRUCTIONS
1. Clean the HEPA filter after every use with the built in pleat cleaner. Fig. 19
Turn the knob on top of the HEPA filter cartridge to clean the
HEPA filter. (Fig. 19)
Cleaning the Debris Screen
1.To remove the debris screen from the dust-bin:
With the trap door open, grasp the frame within the dust –bin and turn clock-wise and remove.
Either brush gently or rinse the frame in lukewarm water to remove any dust that is adhering to the screen. Fig 22
2. Make sure the debris screen is completely dry before refitting to the dust-bin.
3.To refit the debris screen, insert the screen into the dust-bin and turn anti-clockwise to lock. filter and "TapClean“ on a hard surface to remove any residual dust that might be within the filter.
(Fig.20) Fig. 20
3.You can wash / rinse the HEPA filter. (Fig. 21)
Fig. 21
Important: NEVER use the pleat cleaner knob on the HEPA filter if the HEPA filter is wet. Doing so will cause damage to the filter.
Note: We recommend washing the filter once a month or when suction appears reduced. Always allow 24 hours for drying before refitting to the vacuum. The HEPA dust-bin filter should, however, be replaced every three (3) to six (6) months to ensure peak performance of your vacuum.
Please Note: The white material in the
HEPA filter will discolour over time - This is
NORMAL and will NOT affect the performance of the filter.
For Best Performance:
Always empty the dust-bin and clean the
HEPA dust-bin filter and debris screen before each use and during prolonged usage. Never over fill the dust-bin.
Cleaning the Pre-Motor Filter
Located beneath the dust-bin on the vacuum is a pre-motor filter that should be cleaned each time the HEPA filter is cleaned.
1.Remove the dust-bin.
2.Lift the pre-motor filter out.
3.Rinse in lukewarm water and let the filter air dry for 24 hours before re-installing.
4.When the filter is dry, refit to the vacuum.
Do not use a washing machine to rinse the filter. Do not use a hair dryer to dry it.
Air dry only. Never operate the vacuum without ALL filters in place.
Note: This is a washable filter, but we recommend replacing it every three (3) months.
Note: A severely blocked filter should be thoroughly washed with fresh water. A mild detergent can be used if required.
Changing & Cleaning the Charcoal
Exhaust Filter The exhaust filter is located at the front of the vacuum.
Please note; this filter is not washable and should only be cleaned by lightly brushed. It is recommended that the
Charcoal filter be replaced every 3-6 months.
9
OPERATING INSTRUCTIONS
Changing & Cleaning the Charcoal
Exhaust Filter cont.
1.Insert a thumb into the slot on the exhaust filter cover then press down and pull the cover outwards. (Fig. 23)
2.Pull out the exhaust filter frame.
(Fig. 24)
3.Clean the exhaust filter by lightly brushing. Charcoal filters reduce pet odours released from within the vacuum and should be replaced every 3-6 months for optimum performance.
Fig. 23 Fig. 24
Fig. 26
Fig. 27
4. Remove the bottom cover of the floor head. (Fig. 26)
5. Lift the right side of the agitator brush first and then lift the left hand side and lift out the agitator brush. (Fig. 27)
Cleaning & Changing the Belt
Warning: To reduce the risk of electric shock, the power cord must be disconnected before performing any maintenance / trouble shooting checks.
Occasionally the vacuum drive belt will require changing, the frequency of change will depend upon the amount you use your vacuum.
1.Turn the vacuum "Off" and unplug from power supply.
2.Release the handle by pressing on the handle release pedal and pull back on the handle until it releases from its upright position. Turn the vacuum over and place on the floor.
3. With a screw driver remove the five (5) screws on the bottom plate. (Fig. 25)
Fig. 25
6.Carefully remove any belt residue that may exist in the drive belt area.
7. If the drive belt has broken, remove any loose pieces before replacing with a new drive belt.
8. Remove the worn or broken drive belt from the motor drive shaft.
9.Turn the new drive belt sideways then loop it over the motor drive shaft and then over the agitator pulley on the agitator. (Fig.
28)
Fig. 28
Note: The drive belt is consumable part.
Please call 01733 404 709 to buy genuine
Swan spare parts.
10
OPERATING INSTRUCTIONS
Cleaning & Changing the Belt
Please Note:
The agitator end caps show an arrow that indicates the correct direction the agitator must be installed when refitting.
10. Insert both sides of the agitator by placing the end caps of the agitator, down into the slots on each side. Press firmly to make sure that each end is completely inserted.
11. Check to make sure that the belt is centered on the pulley and that the agitator turns.
12. Replace the cover over the floor head base and replace the screws.
Storage
The vacuum handle has a unique handle which folds for easy storage.
1.To fold the handle; turn the folding handle release latch below the handle. (Fig. 29)
Fig. 29
2. Push the handle down until it is in the storage position.
3. To return the handle to the upright position, pull handle upwards to the upright position until you hear the handle lock into place.
4. NOTE: The folding handle release latch is on a spring and will return to its original position.
Motor Thermostat
Important: This unit is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the vacuum off. Should this occur:
1. Turn the vacuum Off.
2. Disconnect the plug from the power source.
3. Check the source of overheating. (i.e. blocked hose or filter)
4. If there is a blocked hose or filter, unblock and clean / replace the filters if necessary.
5. Wait between 30 - 60 minutes before attempting to reuse the vacuum. The thermal protection device should cool down within this time and the vacuum can then be reused.
11
PROBLEM SOLVING
This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem occurs, it usually can be solved quite easily.
Therefore, this checklist is provided for your convenience.
P O S S I B L E
Cleaner Won’t
Run
1. Not properly plugged into outlet.
2. No electricity in wall outlet
3. On/Off switch not turned on.
4. Motor thermostat tripped.
5. Blown fuse/tripped breaker.
1. Plug in firmly.
2. Reset circuit breaker or replace the fuse.
3. Push on/off switch to on.
5. Check fuse or breaker.
1. Full or clogged dust cup.
2. Wrong pile height setting.
3. Clogged nozzle or dust inlet port.
4. Blocked hose – Check behind inspection door (No 20 page 4).
Cleaner Won't
Pick Up
6. Hose not inserted fully. 6. Push hose in securely.
8. HEPA filter needs cleaning or replacing.
9. Debris screen needs cleaning.
8. Clean or replace HEPA Filter.
9. Clean debris screen.
Cleaner Picks Up
Moveable Rugs Or
Pushes Too Hard
Agitator Does
Not Turn
Air Driven
Turbo Brush
Does Not
Rotate Or
Rotates
Slowly
1. setting.
1. Broken drive belt
2 . Belt(s) installed incorrectly. 2. Check belt and agitator bar.
Rotating brush, turbine
1. Clear obstructed. obstructions.
2: Call 01733 404 709
4. HEPA filter or debris screen clogged.
Air Flow Restricted
With Attachment
1. Attachment use restricts air flow.
2. New carpet debris clogging air
Use Sound Changes path.
12
4. Clean HEPA filter or debris screen.
This symbol indicates that this product is classed as Electrical or Electronic
Equipment and should not be disposed of with other household waste.
The Waste Electrical and Electrical Equipment (WEEE) Directive has been introduced across the European Union:
• to recycle waste electrical products using the best available recovery and recycling techniques in order to minimise the impact on the environment
• to treat any hazardous substances and
• to avoid increasing landfill.
WEEE product should be disposed of by handing it over at a designated collection point.
For more information about where you can drop off your waste product for recycling please contact your local authority .
13
SPARES & SERVICE
Service
●
If the vacuum cleaner is malfunctioning or the power cord is damaged in any way, don’t use the vacuum cleaner. The vacuum cleaner must be repaired by a qualified service agent.
●
If you have any problems with your vacuum cleaner, please call the Swan helpline: 01733 404703.
Available Spares:
SU3016/01
SU3010/02
SU3010/03
SU3016/04
SU3016/05
SU3016/06
SU3016/07
SU3017/08
SU3017/09
SU3010/10
SU3010/11
SU3015/12
SU3015/51
Hose
Belt
Beater Bar
Telescopic Tube
Upholstery Tool
Crevice Tool
Dusting Brush
Turbo Brush
Dustbin & Lid
Debris Screen ( not supplied with filter kit )
HEPA Filter
Exhaust Charcoal Filter
Filter Kit
SWAN VACUUM HELPLINE: PLEASE CALL 01733 404703
SWAN VACUUM SPARE PARTS: PLEASE CALL 01733 404709
When calling from outside the UK please use - 00 44 1733 404703
14
Advertisement
