Directed Xpresskit DBALL2 Installation Manual
Directed Xpresskit DBALL2 is a versatile interface module designed for remote start and security installations in Hyundai vehicles with Remote Start Ready (RSR) function, allowing you to start your car remotely without the need for an aftermarket or OEM remote starter. It offers three configuration options for control: 3x OEM Lock Remote Start Activation, RF Kit, or SmartStart (both sold separately). With customizable features and option list, you can tailor the system to your preferences.
Advertisement
Advertisement
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Update Alert : Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
Installation Guide
This guide supports the installation of a offers three (3)
DBALL 2 in Remote Start Ready ( configuration options to control your system: 3x OEM
RSR ) mode. This solution
Lock Remote Start Activation, RF
Kit or SmartStart ( both sold separately).
Remote Start Ready ( RSR ) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an start the vehicle from a distance.
OEM remote starter in order to
Important!
This product is NOT compatible with vehicles equipped with a manual transmission.
Index
02
Installation s
03
05
Programming
Notes..................................................................................................................................................................................
Hard
Feature & Option List..........................................................................................................................................................
Feature Programming.........................................................................................................................................................
07
08
09
09
10
11
LED Diagnostics & Troubleshooting...................................................................................................................................
12
Parking Lightg Error Codes................................................................................................................................................
Limited One-Year Consumer Warranty.......................................................................................................................
........
14
15
Quick Reference Guide......................................................................................................................................................
16
SmartStart Compatible
Start Ready ( RSR ) mode information.
without the use of a remote starter.
See the Module Programming
Remote section for more
® Hyundai is a registered trademark and property of its respective compan y.
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Page 2
Vehicle Application Guide
The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles.
Vehicles
Hyundai
Santa Fe (Smart Key) 2 2 1 1 1 •
Santa Fe Sport (Smart Key) 2 2 1 1 1 •
Legend:
D: Data-to-Data (D2D)
•: D2D & Wire-to-Wire (W2W)
•
•
•
•
•
•
PK: Transponder & Immobilizer Override
AV: Horn & Lights Controls
DL: OE Door Lock & Alarm Controls
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Page 3
Installation Type 1
Refer to the Vehicle Wiring Reference Chart on page 4 for wire color and component location.
MF 11
(white conn. in driver kick panel)
(-) PTS 1:
Orange/Black, pin 3
1 2 3 4 5 6 7 8 9
11
12 13 14 15 16 17 18 19
10
20
(
M04 black conn.
at
PTS switch)
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
(-) PTS 2:
Yellow/Orange, pin 2
21 22 23 24 25 26 27 28 29
31 32 33 34 35 36 37 38
30
39 40 41 42 43 44 45 46 47 48
BCAN Low:
Red, pin 33
BCAN High:
Blue, pin 24
M01-L
(white conn. at s )
1
9
2 3
10 11
4 5 6 7 8
12 13 14
15
16
(-) Parking Lights:
Pink , pin 1 5
Diagnostic connector
1
9
CCAN Low :
Orange , in 1 4
CCAN High :
Green , in 6
8
16
(+) 12V:
Gray/Black , p in 16
(+) Starter:
Pink, p in 11
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) 12V Input: Brown: 7
(+) Ignition Output : Yellow: 8
(+) 12V Input : Red: 13
(-) Ground: Black: 14
(-) PTS 1 Output : Black/White: 1
(-) PTS 2 Output : Green/Black: 2
(-) Parking Lights Output : Red/Black: 4
(+) Accessory Output: Gray: 6
(+) Starter Output: Gray/Black: 7
Immo. Data: Orange/Black: 11
EMS COM:
White/Orange p 32 RF
LED
DBALL 2
Hood Pin
Note: hood pin only required factory hood pin
Remote Start Safety
Override Switch
6: White/Black: (-) Hood Input
EM11
(black conn. in driver kick panel)
You can connect to either a XL 202
RFTD OR a SmartStart module.
Refer to the SmartStart/ XL 202
Installation Notes for more information.
(+) Accessory:
Yellow, p in 3
(+) Ignition:
Green, p in 21
With the exception of the
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Type 1 - Vehicle Wiring Reference Chart
Function
Wire Information
Color Pin Polarity Location
Santa Fe (Smart Key) 2013-2015
Connector Information
Color Pin
12V Red 1 (+) I/P-B, front of dash fuse box. White 4
PTS 1 Orange/Black 3 (-) M04, PTS switch.
Black 12
PTS 2 Yellow/Orange 2
C-CAN High Green 6
(-)
Data
M04, PTS switch.
OBDII.
C-CAN Low Orange 14 Data OBDII.
Black
Black
Black
12
16
16
Parking LightsPink
Starter Pink
Ignition Green
Accessory Yellow
15 (-) M01-L, headlight switch.
11 (+) EM11, driver kick panel.
21 (+) EM11, driver kick panel.
3 (+) EM11, driver kick panel.
EMS COM White/Orange 32 Data EM11, driver kick panel.
B-CAN High Blue 24 Data MF11, driver kick panel.
B-CAN Low Red 33 Data MF11, driver kick panel.
White
Black
Black
Black
Black
White
White
16
46
46
46
46
48
48
Santa Fe Sport (Smart Key) 2013-2015
12V Red 1 (+) I/P-B, front of dash fuse box. White 4
PTS 1 Orange/Black 3 (-) M04, PTS switch.
Black 12
PTS 2 Yellow/Orange 2
C-CAN High Green 6
(-)
Data
M04, PTS switch.
OBDII.
C-CAN Low Orange
Parking LightsPink
Starter Pink
14
15
11
Data
(-)
(+)
OBDII.
M01-L, headlight switch.
EM11, driver kick panel.
Ignition Green
Accessory Yellow
21 (+) EM11, driver kick panel.
3 (+) EM11, driver kick panel.
EMS COM White/Orange 32 Data EM11, driver kick panel.
B-CAN High Blue 24 Data MF11, driver kick panel.
B-CAN Low Red 33 Data MF11, driver kick panel.
Black 12
Black 16
Black 16
White 16
Black 46
Black 46
Black 46
Black 46
White 48
White 48
Locating components in the vehicle
Driver Kick Panel
Rev.: 20170814
Page 4
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Installation Type 2
Refer to the Vehicle Wiring Reference C hart on page 6 for wire color and component location.
(-) PTS 1:
Orange/Black, pin 3
(
MF11 white conn.
in driver k p
(
M04 black conn.
at
PTS switch)
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
(-) PTS 2:
Yellow/Orange, pin 2
M01-L
(white conn. at head light switch)
1
9
2 3 4 5 6 7 8
10 11 12 13 14
15
16
(-) Parking Lights:
Pink , pin 1 5
Rev.: 20170814
Page 5
BCAN Low : Red, pin 39
BCAN High :
Blue , pin 29
Diagnostic connector
1
9
CCAN Low :
Orange , in 1 4
CCAN High :
Green , in 6
8
16
(+) 12V:
Gray/Black , p in 16
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) 12V Input: Brown: 7
(+) Ignition Output : Yellow: 8
(+) 12V Input : Red: 13
(-) Ground: Black: 14
(-) PTS 1 Output : Black White : 1
(-) PTS 2 Output : Green/Black: 2
(-) Parking Lights Output : Red/Black: 4
(+) Accessory Output: Gray: 6
(+) Starter Output: Gray/Black: 7
Immo. Data: Orange/Black: 11
Hood Pin
Note: hood pin only required factory hood pin
Remote Start Safety
Override Switch
6: White/Black: (-) Hood Input
RF
LED
DBALL 2
(+) Accessory:
Yellow p 19
(+) Starter:
Pink p
EMS COM:
White/Orange , p in 6
(+) Ignition:
Green p
EM11
(Red or White conn. in driver kick panel)
You can connect to either a XL 202
RFTD OR a SmartStart module.
Refer to the SmartStart/ XL 202
Installation Notes for more information.
With the exception of the
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Type 2 - Vehicle Wiring Reference Chart
Wire Information
Function Color PinPolarityLocation
Santa Fe (Smart Key) 2016-2017
12V Red
Connector Information
Color
1 (+) EM31, drivers kick panel. White
PTS 1 Orange/Black 3 (-) M04, PTS switch.
PTS 2 Yellow/Orange 2 (-) M04, PTS switch.
C-CAN High Green 6 Data OBDII.
C-CAN Low Orange
Parking LightsPink
Starter
Ignition
Pink
Green
Accessory Yellow
14 Data OBDII.
Black
Black
Black
Black
Pin
15 (-) M01-L,headlight switch. White 16
7 (+) EM11, driver kick panel. Red or White 58
25 (+) EM11, driver kick panel. Red or White 58
19 (+) EM11, driver kick panel. Red or White 58
1
12
12
16
16
EMS COM White/Orange 36 Data EM11, driver kick panel. Red or White 58
B-CAN High Blue 29 Data MF11, driver kick panel. White 68
B-CAN Low Red 39 Data MF11, driver kick panel. White
Santa Fe Sport (Smart Key) 2016-2017
12V Red 1 (+) EM31, drivers kick panel. White
68
1
PTS 1
PTS 2
Orange/Black
Yellow/Orange 2
C-CAN High Green
3
6
(-)
(-)
M04, PTS switch.
M04, PTS switch.
Data OBDII.
Black
Black
Black
12
12
16
C-CAN Low Orange
Parking LightsPink
Starter
Ignition
Pink
Green
14 Data OBDII.
Black
15 (-) M01-L, headlight switch. White
16
16
7 (+) EM11, driver kick panel. Red or White 58
25 (+) EM11, driver kick panel. Red or White 58
Accessory Yellow 19 (+) EM11, driver kick panel. Red or White 58
EMS COM White/Orange 19 Data EM11, driver kick panel. Red or White 58
B-CAN High Blue
B-CAN Low Red
29
39
Data MF11, driver kick panel. White
Data MF11, driver kick panel. White
68
68
Locating components in the vehicle
Driver Kick Panel
Rev.: 20170814
Page 6
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Page 7
SmartStart/ XL 202 Installation Notes
Th e DBALL 2 Remote Start Ready (
Lock Remote Start Activation, RF
RSR ) solution offers three (3)
Kit or SmartStart ( all configuration options to control your system: sold separately)
3x
. This section provides specific installation information for SmartStart and XL 202.
OEM
SmartStart Revision A
SmartStart is optional and not included. It MUST be purchased separately.
Configuration Wires (White & Brown or Blue)
Cut Brown or Blue Loop
OR
DBALL 2
4 pins
SmartStart
CABLE
2 pins, not used
D2D (4 pins, white)
LED
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart Revision B
SmartStart is optional and not included. It MUST be purchased separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
5 pins
4 pins
DBALL 2 THIS SIDE UP
CABLE
2 pins, not used
D2D (4 pins, white)
LED
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
RF Kit
The optional XL 202 and antenna are not included and MUST be purchased separately.
LED
DBALL 2
XOVER
XL202
Prog.
Button
1. Use the D2D Crossover ( XOVER ) cable that is provided with XL
2. The modules must be connected in a specific order. Refer to the
202, and NOT the one in the
Module Programming
DBALL package.
section for more information.
RF Kit & PKE Combination
Refer to the Passive Keyless Entry ( PKE ) Installation Guide (N2102T) for detailed wiring information.
RF Kit , PKE & SmartStart BT Combination
Refer to the Passive Keyless Entry ( PKE ) Installation Guide (N2102T) for detailed wiring information.
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Module Programming
Refer to the LED
Rev.: 20170814
Page 8
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL 202 or SmartStart module to function programming is selected using Xpress VIP version of the application.
DBALL 2, it is important to ensure that the proper feature and
Warning!
To take advantage of advanced features, you must use Xpress VIP 4.5 (and higher) or the Directechs Mobile app.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKL oader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE instructions.
and follow the on screen
When the flashing operation is successful, you can proceed with the programming instructions below.
SmartStart Installation
The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL 2 .
a.
To e nsure that the D2D communication between SmartStart and
Gray wire must be connected to a ground source ( Rev B
DBALL works properly, the
SmartStart), and the Brown or Blue loop must be cut ( Rev A SmartStart).
b.
Do the
NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by
DBALL2 D2D connector.
Connect SmartStart to DBALL using the D2D port.
OR
XL202 Installation
Connect XL 202 to DBALL2 using the D2D port.
SmartStart
XL202
1
2
Connect the 10-pin , 1 2-pin
DBALL, then w ait until the and 14-pin
LED turns harnesses to
ON solid red .
IMPORTANT:
Press
Do NOT press the brake pedal.
the Push-To-Start (PTS) button twice to turn the ignition ON.
1 st
3 rd
2 nd
14-pin
12-pin
&
Solid
Do NOT press the brake pedal
2X ENGINE
START
STOP
PUSH
3 The orange LED and shuts off.
flashes then the green LED turns ON for 3 seconds
4
Press the Push-to-Start (PTS) button once more to turn the ignition OFF.
You have successfully completed the module programming sequence.
Flashes
&
Solid Green or
Orange x3 sec
&
Off
1X ENGINE
START
STOP
PUSH
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Page 9
Module Reset
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
1
If required for your installation, connect the 10-pin & 12-pin and button, then connect the 14-pin harness to the module.
1 st
4 th
2 nd
3 rd
2 Wait 3 seconds until the p rogramming button.
LED turns
The LED turns
ON solid
ON orange then release the solid red.
Solid
&
Release
&
Solid
Hard Reset
Warning A gainst E xecuting a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
1
If required for your installation, connect the 10-pin & 12-pin and button, then connect the 14-pin harness to the module.
1 st
4 th
2 nd
3 rd
14-pin
12-pin
2 Wait 3 seconds until the until the
LED turns
LED starts to flash orange
ON and solid red.
orange , and w ait 10 more seconds
Solid
&
Flashes
3
Release the programming button. The LED turns ON solid red.
Release
&
Solid
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Page 10
Feature & Option List
It is recommended to configure all the features and options listed below using flashing page on www.directechs.com. The web offers more options such as the
EIPS configuration tool found on the module and RSR ; however, manual configuration of the features is possible using the information on this page.
* Default Option
Feat.
1
2
Operation
RFTD Output
Type
Unlock Driver
Priority
Flashes/Options
1. Disabled*
2. RFTD Output
3. SmartStart
*Driver Priority
All
1. Disabled
2. Safelock
3
Smart OEM Alarm
Control
3. Enabled*
Description
Module is connected to a rem ote starter using a standard installation.
Module is connected to an XL202 using an RSR or RXT installation (when available).
Module is connected to Sm artStart using an RSR or RXT installation (when available).
Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.
Unlocks all doors on first press.
The OEM alarm will not be controlled by DBALL2 upon rem ote start. No disarm or arm com m and will be executed at the beginning or end of the sequence; it m ust be controlled by the Rem ote Starter.
Sm art OEM Alarm Control will behave like a standard Safelock feature on a rem ote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown.
Sm art OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the rem ote start sequence, only when required. The reason for this is, factory alarm control m ust often be done by lock or unlock operation. This could create unnecessary actions on door lock m odules, such as the horn to honk. When possible, Sm art OEM Alarm Control will m onitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm , the disarm /rearm will not be executed. Sm art OEM Alarm Control will also m onitor the rem ote starter actions so that the factory alarm control is not done twice. A rem ote starter, for which the Safelock feature is active, will work perfectly with this option and will m ake it invisible to the user.
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Page 11
Feature Programming
Programming
Button
To enter feature programming routine
-
-
Turn t he ignition ON
Within 5 seconds
, then OFF
, press and
.
HOLD
-
Programming button.
The LED will flash green once slowly until the LED turns ON orange ( to indicate the feature number is 1. After a short delay, the the current option of feature 1 repeat until a new command is entered .
LED flashes red rapidly to indicate
Changing feature options
-
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the
DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature.
The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the the number of times to indicate the current feature.
The flashing sequence will repeat until
LED flashes green slowly a new command is entered .
Accessing another feature
-
-
Press and release the programming button a number of times to advance from the current feature to the next desired feature.
The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature.
The flashing sequence will repeat until a new command is entered .
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed
-
-
Other features can be programmed.
The feature programming can be exited.
Exiting feature programming
No activity for 30 seconds; after 30 seconds, the sequence.
-
LED will turn ON orange for 2 seconds to confirm the end of the programming
OR
Press and HOLD the programming button for 3 seconds. After 3 seconds, the end of the programming sequence.
LED will turn ON orange for 2 seconds to confirm the
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Page 12
LED Diagnostics & Troubleshooting
LED Description
Module Programming
Troubleshooting
Off
Solid red
Flashes red
& green
Solid orange
Flashes green
Module has no power.
Waiting to begin the programming sequence.
Initialization failed.
Transponder functions were skipped.
All required CAN networks has been detected.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Ensure the correct programming procedure is being followed.
Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
(If compatible) when RXT mode is not desired or convenience features are needed, please reset and reprogram the module.
Normal operation.
Flashes orange
1 of 2 CAN networks has been detected.
Normal operation
Flashes orange slowly
Key2GO initiated.
Please follow the steps indicated in “Module programming” to complete the Key2GO programming.
Solid green x 3 secs
Module was successfully programmed with all functions. Normal operation
Solid orange x 3 secs
Module was successfully programmed without transponder functions.
Module Programming - Error Codes
Normal operation.
Flashes red x 1
Flashes red x 1
Flashes red x 2
Flashes red x 3
Flashes red x 4
Flashes red x 5
Flashes red x 6
Flashes red x 7
CAN2 not detected.
J1850 not detected.
CAN1 not detected.
Bypass data not detected.
Bypass processing error.
ISO 1 not detected.
ISO 2 not detected.
MUX not detected.
Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try again.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure the vehicle still operates correctly using the factory key.
The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical
Support.
The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections.
The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections.
The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections.
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Page 13
LED Description
External module synchronization
(Flashes red, red then orange) x 10
OBDII feature is not supported.
Activation Ground When Running (Status)
Flashes green
Ground When Running (Status) command received.
Flashes red
& orange
Flashes green quickly
Ignition ON command received.
Start ON command received.
Flashes red x 10
PTS shutdown error.
Flashes red x 21
CAN bus incorrectly detected.
Commands
Flashes orange x 1
LOCK command received.
Flashes orange x 2
UNLOCK command received.
Flashes orange x 3
TRUNK command received.
Flashes orange x 4
AUX1 command received.
Flashes orange x 5
AUX2 command received.
Flashes orange x 6
AUX3 command received.
Shutdown codes
Flashes green x 1
Takeover successful.
Flashes red x 1
Runsafe was not disabled.
Flashes red x 2
Brake was not detected.
Flashes red x 3
Smart key was not detected.
Flashes red x 4
Speed was detected.
Troubleshooting
The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
The module has initialized the remote start sequence.
The module has received the Ignition ON command and is processing the remote start sequence.
The module has received the Start ON command and is processing the remote start sequence.
The PTS output from the module was not activated due to safety protection.
Verify the CAN1 and CAN2 connections. Refer to
“Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections.
If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D.
Normal operation.
No UNLOCK command was received prior to opening the door, or the 45 second timer expired in takeover mode.
The brakes were not detected, which prevents the system from shutting down the vehicle.
The smart key was not detected, which prevents the system from shutting down the vehicle.
The vehicle was detected as moving, which prevents the system from shutting it down.
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Parking Light Error Codes
The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
Flashes Diagnostic
1 Runtime expired.
2
3
4
5
6
Over-rev shutdown.
Low/No RPM.
Transmitter shutdown.
Brake shutdown.
Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
© 2017 Directed. All rights reserved.
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Rev.: 20170814
Limited One Year Consumer Warranty
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed
Electronics. (“ DIRECTED ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY ,
FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL
THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING A GUARANTEE OR
INSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS ,
AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION ,
, .
A CLAIM OR A DISPUTE INVOLVING
TO THE AUTHORIZED DIRECTED DEALER ’S .
LOSS , LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE .
,
MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED ’S OPTION THE
PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of
America or Canada are sold “ ” and shall have NO WARRANTY , express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State.
DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.
For further details relating to warranty information of Directed products, please visit the support section of website at: www.directed.com
DIRECTED ’s
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide.
DISCLAIMER : Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876
B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;
7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:
2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European
Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
© 2017 Directed. All rights reserved.
Quick Reference Guide
DBALL2HYUNDAI4 Remote Start Ready (RSR) Installation
Vehicle Takeover Pit Stop Mode
The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.
1 Press the remote start button on the transmitter to start the vehicle.
*
Press remote start button *
2 Press the Unlock button on the factory or aftermarket remote.*
Press Unlock button on either remote*
Complete the following steps within 45 seconds or the vehicle will shut down.
HOLD
OR
HOLD
3 Enter the vehicle, while making sure the factory remote is inside with you.
Enter vehicle with Smart Key
4 Press the ignition
PTS
ON .
button twice to turn the
2X ENGINE
START
STOP
PUSH
5 Press the brake pedal, put the car in gear and drive off.
Ready to drive off
* Your aftermarket remote may differ from the model shown in the illustrations.
1
2
Stop the vehicle in a safe parking spot and put the gear in Park (P).
&
P
Stop & put vehicle in Park (P)
Press the button to remote start the vehicle.*
The PTS button will flash once to indicate the vehicle is now in P it Stop
Press remote start button *
Mode .
&
ENGINE
START
STOP
Flashes
3
It is now safe to leave the vehicle with the engine running and factory remote in hand.
exit the
HOLD
Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.
E xit vehicle with
Smart Key
* Your aftermarket remote may differ from the model shown in the illustrations.
Parking Light Error Codes
The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start . Each flashing pattern is described below.
Flashes Diagnostic
1
2
3
Runtime expired.
Over-rev shutdown.
Low/No RPM.
4
5
6
Transmitter shutdown.
Brake shutdown.
Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
© 2017 Directed. All rights reserved.
Quick Reference Guide
DBALL2HYUNDAI4 Remote Start Ready (RSR) Installation
Remote Start Ready (
List of Available Commands
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
Button(s)
RSR )
Remote Start Ready ( RSR ) is a function that enables the interface module to remote start the vehicle completely on its own.
Consequently, there is no need for an aftermarket or an OEM starter in order to start the vehicle from a distance.
remote
Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
x1 + x3 + x1 +
Press & hold for 1 second to remote start.
Press & hold for 5 seconds to activate the trunk release (optional).
Press once, then to activate the rear hatch/tail glass release (optional).*
Press 3 times, then the panic mode.
to activate
Press once, then remote starter runtime.
to reset the
* This output is configurable. see your authorized installation center for more information.
SmartStart Compatible
This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.
What is SmartStart?
Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:
Lock/Arm
Unlock/Disarm
Remote Car Starter
Trunk Release
Panic
Aux Channels
You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!
But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.
3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the
Directed Cloud Services ( DCS ) network linking car, app, end user, and the Internet.
For more information, visit www.mysmartstart.com.
3x OEM Lock Remote Start Activation
This solution includes the option to remote start your vehicle by pressing the Lock button 3 times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button 3 times once more.
Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it.
© 2017 Directed. All rights reserved.
Quick Reference Guide
DBALL2HYUNDAI4 Remote Start Ready (RSR) Installation
Engine Idle Protection System ( EIPS )
Vehicles equipped with RFID -type Push-to-Start ignition systems work by detecting could potentially lead users to exiting the vehicle while the engine is still and the car is left idling on its own in a garage or a confined space.
running will detect the presence of the RFID fob in the now vehicle, available on the through the CAN
DBALL . It idling for more than the pre defined runtime ( the fob , DBALL will send a signal to the i.e.
1 to 5 minutes) without vehicle in order to detecting shut off the engine.
EIPS ( )
§ N otify the user about the idling engine by sounding the horn with a series of short
§ S hut down the engine after a pre-defined ( 1 to 5 minutes) .
EIPS a is configured using Xpress
DBALL module is flashed .
VIP . The following window is displayed whenever
Activating/deactivating EIPS :
§ To activate EIPS , remove all keys from the vehicle and close all doors while the engine is running.
§ To deactivate EIPS , do one of the following actions:
Open one of the doors.
Turn the engine off.
Drive the vehicle.*
* The EIPS feature is disabled if the vehicle is in motion so there is no risk that the or not.
Notes
§ If the engine fails to shut down due to some malfunction, mode and will notify the user by all means possible
EIPS
(e.g. h orn will go into alarm or s iren ).
© 2017 Directed. All rights reserved.

Public link updated
The public link to your chat has been updated.
Advertisement