Keystone Interior Aluminum Blinds Installation Instructions

Keystone Interior Aluminum Blinds Installation Instructions
Aluminum Mini Blinds - Installation Instructions
STEP 1: Identify the parts of your aluminum blind (images not to scale)
Top Rail
Control Wand
Lift Cord
Valance Clips
Qty: 2-6 (depending on blind size)
Bottom Rail
Cord Cleat (with 2 small screws)
Qty: 1
Valance Slats
Qty: 2
Mounting Bracket (with large 2 screws per bracket)
Qty: 2-6 (depending on blind size)
STEP 2: Prepare to Install Mounting Brackets
The number of required Mounting Brackets for your blind will depend on its width. The outermost Mounting Brackets should be installed about 1/4 inch from each end of the blind. If you have more than 2 brackets, install all
remaining brackets towards the center of the shade (while avoiding any mechanisms on the inside of the head rail
that will prevent the bracket from correctly snapping into place).
STEP 3: Install Brackets
Wall Installation
For a wall installation, measure 1/4’’ inwards from your temporary
markings and install brackets using two (2) Hex Head Screws
(included) (see figure A). Make sure all brackets are aligned and
level with each other. Tighten screws completely.
Install Screws
here
Figure A
Ceiling Installation
Bracket Lock
For a ceiling installation, measure 1/4’’ inwards from your temporary markings, and
install brackets using two (2) Hex Head Screws (included) (see figure B). Make
sure all brackets are aligned and level with each other. Tighten screws completely.
You may need to slightly alter the position of the bracket lock to access the screw
holes.
Install Screws here
Figure B
and
your blind installation
WAND ASSEMBLY.
Slide plastic collar up the tilter shaft past the hole (See Figure 2).
is
as
easy
as 1.2.3.
hookValance
at top of wand
STEPPlace
4: Install
Clip through tilter shaft hole. Slide plastic collar
3.
Valance slat
Figure 1.
Line up
this edge with
pencil mark
downthe
tilter
shaftoftothe
cover
hook. This
lockthe
thefront
wandedge
in place.
3A
Click
back
Valance
clipwill
over
of the head rail.
Push
the
clip
down
onto
the
top
rail
until
you
hear
it
“click”
into
place.
VALANCE
ASSEMBLY.
MOUNTING
BRACKETS.
Complete
step
forvalance
all(Figure
Valance
Clips
that
were
included
Slide valance
into
clips.
Then
hook
clipsit willwith your blind.
With this
blindslats
fully opened
1), hold
up to
wall valance
in the position
1.
onto top
headrail
(Seeblind
Figure
A). left and right and height is correct.
hang.
Make sure
is centered
3B
Mounting bracket
(If blind
long,
see shortening
instructions,
3). Slats through the
After the
clipsis too
have
been
installed,
slide theFigure
Valance
Line up
this edge with
pencil mark
Mounting bracket
Or
TO OPERATION
BLINDS
Tilter
clips.
Shaft
Important: Always
tilt
blind
horizontally
before
raising
or
lowing.
This
increases
the
life
of
the
blind.
Make sure blind is level. Make pencil marks 1/4” inch past each end of
Figure 2.
Or
headrail.
TO LOWER BLIND:
STEP
5: to
Install
Shade
Move
cord
left pulling
down gently
untilincord
releases.
Allow
cord
Now
place mounting
brackets
level lock
position
on pencil
marks
withto slip through figures until blind reaches
desired
level.the
Move
pull
cord
to
the
right
and
release.
Blind
will
lock
automatically.
Tilter
Hook
front
of
the
blind
onto
the
front
of
the
Figure C
large hole facing the floor (See Figure 1 - mounting brackets). Secure
Cord lock
Wand
brackets
screws.
Bracket,
then with
swing
the back side of the shade
TO RAISE
BLIND:
up
towards
the
back
the Bracket.
MoveRelease
the
Pull cord downward until blindof
reaches
desired height.
cord and blind locks automatically.
2.
Bracket lock into its “locked” position to secure
Valance clip
SNAP
FRONT
CAPS.
TO TILT
BLIND:
your
blind
in ON
place.
If your
bracket lock is alSlide
headrail
into
mounting
brackets.
Rotate wand to
attain
desired
slat
positions.
ready in
the hinged
“locked”
position, you will need to Headrail
Close
door.
unlock itBLIND:
to install your blind.
TO SHORTEN
Valance
Slats
String tape
Lift cord
Slats
After installing blind, check to see exactly how much shorter blindFigure
should
be. First, remove
A
bottomrail buttons with screw driver. Untie knot in lift cord. Pull cord through hole in bottomrail
Bottomrail
Ladder
Button
and holes in slats to desired shortening point. Remove bottomrail and extra slats. Replace
ASSEMBLY.
Position Knot
Locked Position
bottomrail ontoWAND
ladders
nearest desired shortening point. Insert lift cord through hole in bottomrailUnlocked
Figure 1.
Slide plastic
up the
tilterstring
shafttape
past around
the holebottomrail.
(See Figure
Cord
and through buttons
and recollar
tie knot.
Re-tie
Cut2).off excess string tape
Place
hook
atand
topInsert
of
wand
through
tilterbottomrail
shaft hole.holes
Slideand
plastic
collarbuttons.
STEPone
6: Install
Cord
Cleat
leaving
(1”)
inchWand
on ends.
these
ends into
replace
Figure 3.
down tilter shaft to cover hook. This will lock the wand in place.
3A
3B
3.
Important
Note
To Install
the Control Wand, hook it onto the wand hook located on the top rail
VALANCE
ASSEMBLY.
(opposite
the lift
Youfor
may
needreasons.
to slide the protective collar up to access
Always
tie the
cord
to cord).
cord
safety
Slide
valance
slatscleat
into valance
clips. Then hook valance clips
the hook.
the protective
collar
ontoSlide
top headrail
(See Figure
A). back down after installing the wand.
Figure 2.
To
the cord
cleat, use the two included screws and install at your desired
TOinstall
OPERATION
BLINDS
Important:Wrap
Always
blind around
horizontally
raisingtoorkeep
lowing.
Thiscord
increases
height.
thetiltcord
thebefore
cord cleat
your
tight. the life of the blind.
Window
blind
cord
can
STRANGLE
your
child.
See Figure D.
TO LOWER
BLIND:
To prevent
strangulation, purchase cordless products or products with inaccessible cords.
Move cord to left pulling down gently until cord lock releases. Allow cord to slip through figures until blind reaches
cuerda
de lapull
persiana
a su niño.
desiredLalevel.
Move
cordpuede
to theESTRANGULAR
right and release.
Blind will lock automatically.
Figure
D Cleat
Para evitar el estrangulamiento, compre alternativas cuerda o productos con cuerdas inaccesibles.
Cord
TO RAISE BLIND:
Pull cord downward until blind reaches desired height. Release cord and blind locks automatically.
Operation Instructions
String tape
TO TILT BLIND:
Rotate
wand
to attain
desired
To lower
blind:
Move
cordslat
to positions.
left pulling down gently until cord lock releases. Allow cord to lower until blind Slats
reaches
desired
level.
Pull
cord
to
the
right
to
engage
cord
lock.
Release
cord
and
blind
should
remain
at
desired
level.
TO SHORTEN BLIND:
To
raise
blind:
Pull
cord
downward
until
blind
reaches
desired
height.
Release
cord
and
blind
will
lock
automatiAfter installing blind, check to see exactly how much shorter blind should be. First, remove
bottomrail
buttons with screw driver. Untie knot in lift cord. Pull cord through hole in bottomrail
cally.
Ladder
Button
and
holes
in slats
to desired
shortening
point.
bottomrail
extra slats. Replace
To tilt
blind:
Rotate
operation
wand
to Remove
attain desired
slatand
position
Knot
bottomrail onto ladders nearest desired shortening point. Insert lift cord through hole in bottomrail
Cord
and through buttons and re tie knot. Re-tie string tape around bottomrail. Cut off excess string tape
leaving one (1”) inch on ends. Insert these ends into bottomrail holes and replace buttons.
Figure 3.
Important Note
Always tie the cord to cord cleat for safety reasons.
Window blind cord can STRANGLE your child.
To prevent strangulation, purchase cordless products or products with inaccessible cords.
La cuerda de la persiana puede ESTRANGULAR a su niño.
Para evitar el estrangulamiento, compre alternativas cuerda o productos con cuerdas inaccesibles.
www.shadeinfo.com
303.652.6164 (phone)
Cord Cleat
M1035-E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement