Delock 95846 Fingerprint module USB2.0 User Manual 9 Pages
DeLOCK 95846 is a fingerprint sensor USB 2.0 module that provides innovative security, touch pad navigation, and other unique features for PC/NB/UMPC applications. Some of its key capabilities include:
- High-Accuracy Fingerprint Sensing: Featuring patented TruePrint technology, it offers exceptional ability to acquire and enroll fingerprints, with a false acceptance rate of less than 1:100,000 and a false rejection rate of less than 1:500.
- Durable Construction: The ultra-hard wearing surface coating can withstand over 10 million rubs without degradation, ensuring longevity and reliability.
advertisement
Specification
95846
Delock industry fingerprint sensor USB 2.0 module
20,80
23,45
2,00 date: 29.05.2009
Specification
95846
Delock industry fingerprint sensor USB 2.0 module
Contents: device overall description features specification compliance block diagram host interface connector power consumption software & OS support pinout and definition mechanical dimension
Specification
95846
Delock industry fingerprint sensor USB 2.0 module
Device overall description
The 95846 is a is a breakthrough slide sensor – delivering the industry’s most innovative security, touch pad navigation, and other unique features in the smallest solution for PC/NB/UMPC applications.
It is based on Authentec AES1610 fingerprint slide Sensor module that employs
AuthenTec’s award winning TruePrint® and TrueMatch technologies, the most accurate sensor and pattern matching technologies in the industry. Authentec
AES1610 integrates AuthenTec’s next generation TrueFinger™ anti-spoofing protection, TruePrint technology provides the most accurate fingerprint image and
TrueMatch pattern matching technology runs on the highperforming host processor
Specification
95846
Delock industry fingerprint sensor USB 2.0 module
-
Features
Authentec AES1610 Fingerprint Sensor,
Patented truePrint technology for best ability to acquire (ATA), best ability-to-enroll
(ATE) >>99%, false acceptance rate (FAR) <1:100,000, and lowest false rejection rate (FRR) < 1:500 high definition 128 X 8TtruePrint technology based pixels , 500 pixel per inch (ppi) array
Ultra-hard wearing surface coating is scratch and impact resistant > 10 Million rubs w/o degradation
IEC 61000-4-2 Level 4 ESD immunity (+/- 15KV Air)
USB 2.0 full speed(12 Mbits/s) interface with suspend and remote wakeup
Full support for C3 selective suspend mode
Built-in low power finger detection w/ remote wakeup capability
The slide speed of the device is selectable and ranges from 20cm/s to 50cm/s during an imaging event, the RF TruePrint signal is conducted via the drive ring to the users’ finger. TheTruePrint signal is then conducted through and modulated by the “live layer” of the finger where the true fingerprint originates. The imaging array measures the TruePrint signal, the strength of which corresponds to either a ridge or valley region. The sensing element of each pixel is an RF sense-amplifier, which picks up the TruePrint (high frequency AC) signal.
Specification
95846
Delock industry fingerprint sensor USB 2.0 module
Specification Compliance
- USB Specification V2.0 Full Speed (12Mbits/s)
Block Diagram
Power consumption ( Draft !
) electrical characteristics supply voltage normal waiting for finger idle USB suspend imaging/finger swiping @30cm/s minimum typical maximum units
3,15 3,3 3,45 V
4,4
0,4
37 mA mA mA temperature range ambient operating temperature range storage temerature range minimum typical maximum units
0 70 °C
-20 85 °C
Specification
95846
Delock industry fingerprint sensor USB 2.0 module
Host interface connector
- Aces 88460-0401, pitch=0.8mm Height 1.8mm RA type
Software & OS support
3rd Party vendor support from
Arachnoid Technology (ABIG), Bio-Me
Bio-Key International
Cogent Systems
EZValidation
M2SYS Technology
Phoenix Technologies silex technology america, Inc.
Softex Incorporated, Omnipass
Pinout and Definition
Pin#
1
2
3
4 signal name description signal GND ground for signal
USB_D+ USB data plus
USB_DUSB data minus
Vcc main power input 3,3V DC
* Pls make sure the module is FULLY grounded(via screw ground plate) to chassis ground or USB shield ground to ensure ESD result.
Specification
95846
Delock industry fingerprint sensor USB 2.0 module
Mechanical dimension
(Dimensions might change without prior notice, pls always enquire in advance)
- 23.45 mm x 20.8mm x 4.44 mm (L x W x H) 1.8mm ACES 88460 connector +
0.8mm PCB + 1.84mm sensor height
Specification
95846
Delock industry fingerprint sensor USB 2.0 module
Figure 3-2 40 BGA eXtendaBall thick package
Specification
95846
Delock industry fingerprint sensor USB 2.0 module
advertisement
Related manuals
advertisement