BMW B58TU Reference Manual
The BMW B58TU is a powerful and efficient engine that features a number of innovations, including a new cylinder head with an integrated exhaust manifold, a single-part chain drive, and split cooling. The B58TU is designed for optimal performance and reduced emissions, while still offering the power and reliability you expect from BMW. This manual provides detailed product information and technical data for the B58TU engine, including its mechanical, vacuum supply, cooling, intake air and exhaust systems, fuel system, and engine electrical system.
Advertisement
Advertisement
cal
cont ess ned thi manual s esol ansf
Technical�training.
Product�information.
B58TU�Engine
BMW�Service
General�information
Symbols�used
The�following�symbol�is�used�in�this�document�to�facilitate�better�comprehension�or�to�draw�attention to�very�important�information:
Contains�important�safety�information�and�information�that�needs�to�be�observed�strictly�in�order�to guarantee�the�smooth�operation�of�the�system.
Information�status:�July�2018
BMW�Group�vehicles�meet�the�requirements�of�the�highest�safety�and�quality�standards.�Changes in�requirements�for�environmental�protection,�customer�benefits�and�design�render�necessary continuous�development�of�systems�and�components.�Consequently,�there�may�be�discrepancies between�the�contents�of�this�document�and�the�vehicles�available�in�the�training�course.
The�information�contained�in�the�training�course�materials�is�solely�intended�for�participants�in�this training�course�conducted�by�BMW�Group�Technical�Training�Centers,�or�BMW�Group�Contract
Training�Facilities.
This�training�manual�or�any�attached�publication�is�not�intended�to�be�a�complete�and�all�inclusive source�for�repair�and�maintenance�data.�It�is�only�part�of�a�training�information�system�designed�to assure�that�uniform�procedures�and�information�are�presented�to�all�participants.
For�changes/additions�to�the�technical�data,�repair�procedures,�please�refer�to�the�current�information issued�by�BMW�of�North�America,�LLC,�Technical�Service�Department.
This�information�is�available�by�accessing�TIS�at�www.bmwcenternet.com.
Additional�sources�of�information
Further�information�on�the�individual�topics�can�be�found�in�the�following:
• Owner's�Handbook
• Integrated�Service�Technical�Application
• Aftersales�Information�Research�(AIR)
The�information�contained�in�this�manual�is�not�to�be�resold,�bartered,�copied,�or�transferred without�the�express�written�consent�of�BMW�of�North�America,�LLC�(“BMW�NA”).
©2018�BMW�of�North�America,�LLC
The�BMW�name�and�logo�are�registered�trademarks.�All�rights�reserved.
B58TU�Engine
Contents
1.
Introduction
1
1.1.
1.2.
1.2.1.
1.2.2.
2
3
4
4
2.
Engine�Mechanical
5
2.1.
2.2.
5
2.1.1.
2.1.2.
5
6
7
2.3.
2.2.1.
7
10
2.3.1.
10
3.
Vacuum�Supply
12
3.1.
12
4.
Cooling�System
13
4.1.
4.2.
4.3.
13
4.1.1.
4.1.2.
16
Switching�logic�of�split�cooling�valve
................................................................................................
17
18
4.4.
Operating�strategy�of�the�heat�management�module
..............................................................................
20
4.3.1.
4.3.2.
4.3.3.
4.3.4.
21
22
23
24
25
5.
Intake�Air�and�Exhaust�System
26
5.1.
5.2.
26
5.1.1.
5.2.1.
26
27
27
6.
Fuel�System
28
6.1.
28
6.1.1.
6.1.2.
29
30
7.
Engine�Electrical�System
33
B58TU�Engine
Contents
7.1.
7.2.
Digital�Motor�Electronics�(DME)
33
34
B58TU�Engine
1.�Introduction
The�product�information�"B58�Engine"�serves�as�the�basis�for�this�document.�This�document exclusively�describes�the�changes�to�the�B58�engine�and�serves�to�support�Technical�Service.
Due�to�the�huge�similarities,�the�two�engines�are�described�in�the�one�document.
1
B58TU�Engine
1.�Introduction
1.1.�Innovations
To�meet�the�legal�requirements�for�emissions,�a�number�of�technical�improvements�have�been implemented.�The�technical�updates�for�the�B58TU�engine�include�the�following�new�features:
New�features�on�the�B58TU�engine
2
B58TU�Engine
1.�Introduction
F
G
B
C
D
E
Index
A
Explanation
Fuel�preparation�with�350 bar�injection�pressure
Cylinder�head�with�integrated�exhaust�manifold
Adapted�exhaust�turbocharger�made�from�steel
Split�cooling
Coolant�pump�with�integrated�pressure�relief�valve
Heat�management�module�with�electric�split�cooling�valve
Single-part�chain�drive
Weight�savings�in�the�crankshaft�drive�area,�injection�pressure�boosting�in�the�fuel�preparation�area, and�function�changes�in�the�engine�cooling�area�have�made�it�possible�to�reduce�the�CO
2.5%,�while�increasing�engine�performance�by�10 kW/50 Nm.�(13�hp/36�lb-ft)
2
�emissions�by
1.2.�Technical�data
The�following�engine�versions�are�described�in�this�product�information:
Output�in�[kW/(hp)] at�[rpm]
Torque�in�[Nm/(lb-ft)] at�[rpm]
Displacement�in�[cm³]
Bore�hole�/�Stroke�in�[mm]
Compression�ratio
Combustion�process
Maximum�rotational�speed
Short-term�overspeed�(overboost)�15�s
Idle�speed
Permissible�fuel�range
B58B30M1
250�(335)
5500�-�6500
450�(330)
1500�-�5200
2998
82/94.6
11.0�:�1
Turbo-Valvetronic�direct�injection
6500
7000
660
ROZ�87–98
3
B58TU�Engine
1.�Introduction
1.2.1.�Performance�diagrams
Comparison�of�performance�curves�between�B58B30M1�and�B58B30M0�engine
1.2.2.�Model�overview
The�following�table�provides�an�overview�of�the�models�in�which�the�new�B58TU�engine�is�used�from
07/2018:
Model
BMW�X5�xDrive40i�(G05),�from�07/2018
BMW�X7�xDrive40i�(G07),�from�12/2018
Engine
B58B30M1
B58B30M1
4
B58TU�Engine
2.�Engine�Mechanical
2.1.�Engine�housing
2.1.1.�Cylinder�head
The�following�figures�show�the�two�cylinder�head�variants�with�and�without�the�cylinder head-integrated�exhaust�manifold.
Cylinder�head�of�B58TU�engine
Index
A
B
Explanation
Cylinder�head�with�integrated�exhaust�manifold�ZIAK¹
Cylinder�head�without�integrated�exhaust�manifold�nZIAK²
ZIAK¹�=�cylinder�head-integrated�exhaust�manifold nZIAK²�=�non�cylinder�head-integrated�exhaust�manifold
With�the�gravity�casting�process�the�aluminum�alloy�is�embedded�into�a�prefabricated�mould�of steel�and�sand�using�gravity.�The�result�is�a�cylinder�head�made�from�aluminum�gravity�die�casting
AlSi7MgCu0.5�T5.
The�cylinder�head�of�the�B58TU�engine�in�the�medium�power�level�is�a�new�design.�The�exhaust manifold�was�integrated�in�the�housing�of�the�cylinder�head.�Depending�on�the�engine�output,�the engine�weight,�the�operating�strategy�of�the�engine�and�the�cooling�surfaces,�the�exhaust�manifold is�integrated�in�the�cylinder�head�housing�and�the�exhaust�turbocharger�is�interlocked�at�the�cylinder head.
Owing�to�the�higher�mechanical�and�thermal�loads,�gasoline�engines�in�the�upper�power�levels�and higher�have�a�traditional�cylinder�head� without �the�exhaust�manifold�integrated�in�the�cylinder�head.
The�following�benefits�could�be�achieved�with�the�integration�of�the�exhaust�manifold�in�the�cylinder head�housing:
• Benefits�in�fuel�consumption�and�pollutant�emissions�due�to�faster�warm-up�of�the�engine.
• Weight�reduction�with�the�use�of�aluminum�instead�of�steel.
• Cost�reduction�by�eliminating�the�need�for�a�separate�exhaust�manifold.
• Simple�disassembly�and�installation�both�of�the�cylinder�head�and�the�exhaust�turbocharger.
The�following�table�provides�an�overview�of�the�engine�versions�that�use�a�cylinder�head�with�an integrated�exhaust�manifold:
5
B58TU�Engine
2.�Engine�Mechanical
Engine version
Power�level
Cylinder�head
3.0 l
Medium�power�level
Cylinder�head-integrated exhaust�manifold�ZIAK
B58TU�Engine
3.0 l
Upper�power�level
Non�cylinder�head-integrated exhaust�manifold�nZIAK
2.1.2.�Crankcase
Honing�process
Honing�process�"old/new"
Index
A
B
Explanation
Previous�manufacturing�process�of�internal�cylindrical�honing
New�manufacturing�process�of�form�honing
6
B58TU�Engine
2.�Engine�Mechanical
The�cylindrical�bore�hole�of�a�combustion�engine�becomes�deformed�during�the�operating�condition by�thermal�loads.�Form�honing�allows�this�deformation�to�be�achieved�in�production,�so�that�there�is�an almost�cylindrical�shape�in�the�operating�condition.�This�has�a�positive�effect�on�the�emissions�quality, oil�and�fuel�consumption,�as�well�as�output�and�wear.
2.2.�Crankshaft�drive
2.2.1.�Chain�drive
Features:
• Chain�drive�at�the�side�of�the�engine�emitting�the�forces
• Single-part�chain�drive�for�driving�the�camshafts
• Single�sleeve-type�chain�8 mm
• Electric�motor�of�the�combined�oil-vacuum�pump�via�a�separate�chain
• Plastic�tensioning�and�guide�rail
• Hydraulic�chain�tensioner�with�spring�preload�and�sealing�sleeve.
7
B58TU�Engine
2.�Engine�Mechanical
Comparison�of�the�chain�drive�of�B58�engine�and�B58TU�engine
Index
7
8
9
5
6
1
2
A
B
3
4
Explanation
Two-part�chain�drive
Single-part�chain�drive
Slide�rail
Top�timing�chain
Chain�tensioner
Tensioning�rail
Bottom�timing�chain
Camshaft�sprocket,�oil�vacuum�pump
Drive�chain,�oil�vacuum�pump
Guide�rail
Timing�chain
8
B58TU�Engine
2.�Engine�Mechanical
The�main�difference�between�the�chain�drive�compared�with�the�B58�engine�is�the�move�from�a�twopart�timing�chain�drive�to�a�single-part�timing�chain�drive.�Deflection�via�the�intermediate�shaft�on�the top�timing�chain�and�the�second�timing�chain�is�no�longer�needed.�The�chains�used�here�are�8 mm sleeve-type�chains.�Because�the�intermediate�gearing�is�no�longer�needed,�the�number�of�teeth�on�the crankshaft�(23 teeth)�and�the�VANOS�adjuster�(46 teeth�each)�has�also�changed.
Chain�track
Comparison�between�chain�track�of�B58�engine�and�B58TU�engine
3
4
5
B
1
2
Index
A
Explanation
Chain�track,�two-part�timing�chain�drive�B58�engine
Chain�track,�single-part�timing�chain�drive�B58TU�engine
6-cylinder�engine
Upper�timing�chain
Timing�chain
Lower�timing�chain
Drive�chain,�oil�vacuum�pump
The�way�the�combined�oil�vacuum�pump�is�driven�via�a�separate�drive�chain�from�the�crankshaft�has not�changed�compared�with�the�Bx8�engines.�Only�the�change�of�the�chain�tracks�has�changed:
The�drive�chain�of�the�oil�vacuum�pump�is�now�in�front�of�the�timing�chain.
Dropping�the�second�timing�chain�offers�the�following�benefits:
• Improved�acoustics
• Lower�space�requirement
• Reduced�weight
9
B58TU�Engine
2.�Engine�Mechanical
Chain�tensioner
Chain�tensioner,�Bx8TU�engine
2
3
Index
1
Explanation
Tensioning�rail
Sealing�sleeve
Chain�tensioner�with�screw�thread
Due�to�the�cylinder�head�manufacturing�process,�the�chain�tensioner�now�has�a�sealing�sleeve�with a�height�of�12.5 mm�instead�of�a�sealing�ring.�The�spring�force�of�the�chain�tensioner�lies�between
40 Nm�(extended)�and�90 Nm�(retracted).
2.3.�Valve�gear
2.3.1.�VANOS
10
B58TU�Engine
2.�Engine�Mechanical
Index
A
B
Explanation
VANOS�B58�engine
VANOS�B58TU�engine
Following�the�changeover�from�a�two-part�chain�drive�to�a�single-part�chain�drive,�the�camshaft sprockets�on�the�VANOS�now�need�46�teeth�instead�of�the�previous�36�teeth.�To�compensate�for�the additional�weight�of�the�larger�camshaft�sprockets,�the�adjuster�was�designed�to�be�shorter�and�more compact.
11
B58TU�Engine
3.�Vacuum�Supply
3.1.�Vacuum�pump
Oil�vacuum�pump,�B58/B58TU�engine
Index
A
B
1
2
Explanation
B58�engine,�tandem�oil�pump�with�integrated�vacuum�pump
B58TU�engine,�oil�pump
Vacuum�pump
Oil�pump
Vehicles�with�a�gasoline�engine�and�"traditional�brake�system"�need�a�vacuum�pump�to�boost�the pedal�force.�In�vehicles�with�a�gasoline�engine�and�DSCi�brake�system�no�vacuum�boost�is�required�as in�the�DSCi�brake�system�the�pedal�force�is�boosted�hydraulically.�The�graphics�show�the�oil�pumps�of the�B58�engine�and�the�B58TU�engine�with�combined�vacuum�pump�and�without�vacuum�pump.
12
B58TU�Engine
4.�Cooling�System
4.1.�Split�cooling
A�new�development�for�the�B58TU�engine�is�the�split�cooling.�A�cooling�concept�which�is�used�the
N63�TU2.
The�split�cooling�function�uses�the�electric�split�cooling�valve,�eSCV,�to�enable�on-demand�decoupling of�the�crankcase�from�the�coolant�flow�both�in�the�warm-up�phase�and�in�partial�load�operation.�In�this situation,�the�coolant�is�exclusively�routed�through�the�cylinder�head.�The�engine�reaches�its�operating temperature�more�quickly�in�the�warm-up�phase,�and�can�be�operated�with�reduced�emissions�in partial�load�operation.
Cooling�circuit,�B58TU�engine
13
B58TU�Engine
4.�Cooling�System
4
5
B
1
2
3
Index
A
Explanation
High�cooling�requirement,�split�cooling�cylinder�head
Low�cooling�requirement,�split�cooling�crankcase
Cylinder�head
Crankcase
Heat�management�module
Electric�Split�Cooling�Valve�(eSCV)
Coolant�pump
14
B58TU�Engine
4.�Cooling�System
Cooling�system�for�B58TU�engine
15
B58TU�Engine
4.�Cooling�System
14
15
16
10
11
12
13
6
7
8
9
2
3
4
5
Index
1
Explanation
Coolant�radiator
Coolant�temperature�sensor,�radiator�outlet
Electric�fan
Electric�split�cooling�valve
Coolant�pump
Pressure�relief�valve
Coolant�temperature�sensor,�crankcase
Crankcase
Cylinder�head
Exhaust�turbocharger
Heating
Component�temperature�sensor
Expansion�tank
Engine�oil/coolant�heat�exchanger
Transmission�oil/coolant�heat�exchanger
Heat�management�module
In�split�cooling,�the�cooling�requirements�for�the�crankcase�and�the�cylinder�head�are�managed�by�the electric�split�cooling�valve.�The�fact�that�the�engine�reaches�operating�temperature�more�quickly�again translates�to�substantial�consumption�and�emission�reductions.
4.1.1.�Split�cooling�valve
Heat�management�module�with�electric�split�cooling�valve
16
B58TU�Engine
4.�Cooling�System
Index
1
Explanation
Electric�split�cooling�valve
To�guarantee�optimal�heat�distribution�during�the�cylinder�head�and�crankcase�warm-up,�the�coolant supply�for�the�cylinder�head�and�crankcase�is�controlled�individually.�The�coolant�is�controlled�by�the
Digital�Motor�Electronics�(DME).�The�coolant�is�distributed�by�the�electric�split�cooling�valve�on�the heat�management�module�in�the�warm-up�phase�such�that�substantially�more�coolant�is�available�to the�cylinder�head�than�to�the�crankcase.�Depending�on�the�engine's�operating�condition,�the�Digital
Motor�Electronics�(DME)�decide�on�the�distribution�of�the�coolant�quantity�to�the�cylinder�head�and�the crankcase�as�required.
Direct�current�motor�(DC)
Voltage�range�in�volts�(V)
Power�consumption�in�ampere�(A)
Control�frequency�of�the�DC�motor�(kHz)
Gear�reduction
Adjustment�speed�per�second
B58TU�engine
6�-�16
0.4�-�1
1
1�:�440
65.5°
4.1.2.�Switching�logic�of�split�cooling�valve
Switching�logic�of�electric�split�cooling�valve
17
B58TU�Engine
4.�Cooling�System
% x
1
B
C
Index
A
Explanation
End�stop
Delivery�position
End�stop
Valve�opening�in�%
Rotary�valve�position�in�degrees,�angle�of�rotation
Rotary�valve
The�diagram�shows�the�switching�logic�of�the�electric�split�cooling�valve.�Depending�on�the�operating condition�and�coolant�temperature�of�the�engine,�as�well�as�the�driver's�desired�load,�the�Digital�Motor
Electronics�(DME)�releases�the�coolant�access�from�the�crankcase�to�a�greater�or�lesser�extent�via�the rotary�valve�of�the�split�cooling�valve.�The�coolant�now�also�flows�through�the�crankcase�and�cools components.
A�bleeding�procedure�in�line�with�the�repair�instructions�is�required�following�a�part�exchange�in�the cooling�system�or�refilling�of�the�cooling�system.�Filling� without �a�vacuum�filler�device�(watering can�filling)�is� not�approved ��There�is�a�risk�of�engine�damage�in�case�of�failure�to�comply��The�filling specification� must �be�observed�
Operation�of�the�vehicle�is�not�permitted�without�completing�the�entire�filling�and�bleeding�routine.
There�is�a�risk�of�functional�limitations�or�overheating.
4.2.�Heat�management�module
The�function�of�the�heat�management�module�is�similar�to�that�of�the�heat�management�module�of�the
B58�engine.
B58TU�engine�heat�management�module
18
B58TU�Engine
4.�Cooling�System
6
7
2
3
4
5
Index
1
Explanation
Coolant�output�towards�the�coolant�pump
Electric�split�cooling�valve
Coolant�outlet�to�coolant�radiator
Electrical�actuator,�heat�management�module
Coolant�entry,�split�cooling�valve
Coolant�entry,�heat�management�module
Coolant�outlet,�heating
A�rotary�valve�inside�the�heat�management�module�ensures�needs-driven�cooling�of�the�various�engine components.�The�opening�cross-sections�of�the�various�coolant�ducts�can�be�opened�or�closed variably.�A�position�sensor�in�the�electrical�actuator�of�the�heat�management�module�forwards�the current�position�of�the�rotary�valve�to�the�Digital�Motor�Electronics�(DME).�The�exact�position�of�the rotary�valve�can�thus�be�determined�so�that�it�opens�or�closes�a�precisely�defined�cross-section�with respect�to�the�various�coolant�ducts.�Adjusting�the�cross-sections�ideally�adapts�the�flow�rates�of�the coolant�ducts�connected�to�the�heat�management�module�to�the�engine�operating�points.�To�correctly position�the�rotary�valve,�the�Digital�Motor�Electronics�(DME)�require�information�including�the�coolant temperature�from�the�coolant�temperature�sensor,�and�the�material�temperature�of�the�cylinder�head from�the�component�temperature�sensor�.�Warm-up�and�cooling�of�the�engine�and�the�supply�to ancillary�components�can�be�implemented�as�driven�by�requirements,�thus�optimizing�consumption.
The�following�tables�provide�an�overview�of�the�technical�data�of�the�heat�management�modules:
Direct�current�motor�(DC)
Voltage�range�in�volts�(V)
Power�consumption�in�ampere�(A)
Gear�reduction
Adjustment�speed�per�second
B58�engine
6�-�16
0.3�-�1.5
1�:�492
40°
B58TU�engine
9�-�16
0.5�-�0.8
5�:�769
64°
Position�sensor
Voltage�range�in�volts�(V)
Power�consumption�in�milliampere
(mA)
Output�signal
Rotational�angle�of�the�rotary�valve
*�SENT�report�=� S ingle� E dge� N ibble� T ransmission
B58�engine
4.5�-�5.5
20�-�35
SENT�report*
200°
B58TU�engine
4.5�-�5.5
20�-�25
SENT�report*
165°
19
B58TU�Engine
4.�Cooling�System
4.3.�Operating�strategy�of�the�heat�management�module
The�following�graphic�shows�the�positions�of�the�rotary�valve�as�the�coolant�temperature�increases.
Circuit�diagram�of�heat�management�module�in�B58TU�engine
Index x
1
2
3
B
C
D
E
0 %
100%
A
Explanation
Rotary�valve�closed
Rotary�valve�open
Cold�start
Warm-up�phase
Operating�temperature
Transition�from�normal�operation�to�maximum�cooling�requirement
Maximum�cooling�requirement
Rotational�angle�in�angular�degrees
Heater�circuit
Main�coolant�circuit
Minor�coolant�circuit
The�openings�on�the�rotary�valve�vary�the�cross-sections�of�the�different�coolant�ducts�as�a�function of�the�rotational�angle�of�the�rotary�valve.�The�following�graphics�schematically�represent�the�various engine�operation�phases,�from�cold�start�to�maximum�cooling�requirement.
20
B58TU�Engine
4.�Cooling�System
4.3.1.�Cold-start�phase
Point�A�in�the�heat�management�module�circuit�diagram�designates�the�cold�start�with�an�engine�that has�completely�cooled�down.
Cold-start�phase,�Bx8TU�engine
In�the�cold-start�phase,�the�coolant�circulates�exclusively�via�a�bypass�in�the�coolant�pump.�The�rotary valve�in�the�heat�management�module�closes�the�coolant�lines�so�that�the�excess�pressure�that�builds up�opens�the�pressure�relief�valve�in�the�coolant�pump�(opening�pressure�2.1 bar)�and�the�coolant�is recirculated�in�the�coolant�pump.
Because�the�coolant�circuits�through�the�exhaust�turbocharger�and�the�ventilation�line�of�the�cylinder head�cannot�be�closed,�a�low�volumetric�flow�is�returned�to�the�coolant�pump�here.
21
B58TU�Engine
4.�Cooling�System
4.3.2.�Warm-up�phase
Area�B�in�the�circuit�diagram�for�the�heat�management�module�shows�the�opening�angle�of�the�rotary valve�in�the�warm-up�phase.
Warm-up�phase,�Bx8TU�engine
In�the�warm-up�phase,�the�heat�management�module�additionally�opens�the�connection�to�the�heating in�addition�to�opening�the�bypass�line.�The�coolant�flows�through�the�cylinder�head,�the�exhaust turbocharger�and�the�engine�oil/coolant�heat�exchanger.�The�electric�split�cooling�valve�is�closed;�no coolant�flows�through�the�engine�block�(split�cooling).
22
B58TU�Engine
4.�Cooling�System
4.3.3.�Operating�temperature
The�positions�of�the�rotary�valve�at�engine�operating�temperature�are�shown�by�area�C�of�the�circuit diagram.
Operating�temperature,�Bx8TU�engine
The�graphic�shows�control�with�the�engine�at�operating�temperature.�The�position�of�the�rotary�valve means�that�the�cross-sections�of�the�respective�coolant�lines�are�open�to�a�greater�or�lesser�extent depending�on�the�coolant�temperature.�The�coolant�flows�with�a�varying�volumetric�flow�through�the small�coolant�circuit,�the�large�coolant�circuit�and�the�heater�circuit.�Depending�on�the�load�request, the�crankcase's�coolant�connection�is�opened�by�the�electric�split�cooling�valve,�thus�cooling�the crankcase.�Large�engine�operation�ranges�are�covered�with�the�crankcase�coolant�circuit�closed.
23
B58TU�Engine
4.�Cooling�System
4.3.4.�Maximum�cooling�requirement
The�maximum�cooling�requirement�is�shown�at�point�E�of�the�heat�management�module�circuit diagram.
Maximum�cooling�requirement,�Bx8TU�engine
To�provide�maximum�cooling�at�high�dynamic�loads�and/or�high�ambient�temperatures,�the�radiator connection�is�fully�opened�(100%)�and�the�small�coolant�circuit�is�completely�closed.�Additionally, the�heater�circuit�is�90%�closed�to�achieve�the�maximum�cooling�thanks�to�the�maximum�coolant volumetric�flow�through�the�large�coolant�circuit.
24
B58TU�Engine
4.�Cooling�System
4.4.�Coolant�pump
The�layout�and�function�of�the�coolant�pump�have�been�revised�and�adapted�to�match�the�cooling concept�of�the�Bx8 TU engines.
Coolant�pump,�Bx8TU�engine
Index
A
B
Explanation
Pressure�relief�valve�closed�(pressure < 2.1 bar)
Pressure�relief�valve�opened�(pressure > 2.1 bar)
A�pressure�relief�valve�is�installed�in�the�mechanical�coolant�pump�housing.�In�combination�with�the heat�management�module,�the�pressure�relief�valve�on�the�one�hand�ensures�that�the�engine�operating temperature�is�reached�more�quickly,�while�at�the�same�time�reducing�leaks�and�component�damage due�to�high�pressure�in�the�cooling�system.
If�an�excess�pressure�of�more�than�2.1 bar�builds�up�in�the�coolant�circuits,�the�pressure�relief�valve opens�and�releases�a�bypass�channel.�The�coolant�is�now�exclusively�circulated�in�the�pump�body.
Once�the�pressure�drops�below�2.1 bar�or�the�engine�speed�rises�above�3000�rpm,�the�pressure�relief valve�closes�and�the�coolant�is�again�routed�through�the�engine's�coolant�ducts.
25
B58TU�Engine
5.�Intake�Air�and�Exhaust�System
5.1.�Crankcase�monitoring
5.1.1.�On-board�diagnosis
Feed-in�point�of�the�blow-by�gases�to�the�clean�air�line�upstream�from�the�exhaust�turbocharger
Index
1
2
3
4
5
6
7
8
Explanation
Non-return�valve
Connection�to�exhaust�turbocharger
Captive�screws
Crankcase�bleeding�connection
Tank�ventilation�connection
Connection�to�clean�air�line
Aluminum�heating�pipe
Electrical�connection�of�heating�element
Owing�to�the�stricter�legislation�in�the�USA,�the�engines�for�the�US�market�have�an�OBD�concept
"pressure�sensor".�With�a�differential�pressure�sensor�in�the�tank�ventilation�system�and�the�hot�film air�mass�meter,�leaks�in�the�crankcase�ventilation,�tank�ventilation,�as�well�as�the�blow-by�lines�can�be identified.�Via�a�feed-in�point�at�the�exhaust�turbocharger�the�blow-by�gases�are�fed�back�into�the�clean air�line�of�the�air�intake�system.
26
B58TU�Engine
5.�Intake�Air�and�Exhaust�System
5.2.�Exhaust�turbocharger
5.2.1.�B58TU�exhaust�turbocharger
Exhaust�turbocharger�in�the�B58TU�engine
Index
A
B
Engine�version
Cylinder�head
Explanation
Exhaust�turbocharger�made�of�steel,�for�cylinder�head-integrated�exhaust manifold�ZIAK¹
Exhaust�turbocharger�made�of�steel,�for�non�cylinder�head-integrated�exhaust manifold�nZIAK²
ZIAK¹�=�cylinder�head-integrated�exhaust�manifold nZIAK²�=�non�cylinder�head-integrated�exhaust�manifold
Due�to�the�exhaust�manifold�integrated�into�the�cylinder�head,�the�exhaust�manifold�and�exhaust turbocharger�housing�are�no�longer�designed�as�a�single�component�for�the�B58TU�engine.�This means�that�the�exhaust�turbocharger�can�be�individually�replaced.�The�charging�pressure�is�still controlled�by�an�electrical�wastegate�valve.
The�exhaust�manifold�and�exhaust�turbocharger�housing�on�the�B58TU�engine�can�be�implemented either�as�one�part�or�separately.�Depending�on�the�engine�version,�the�exhaust�turbocharger�can�be replaced�individually.�The�following�table�shows�which�variant�is�used�by�which�engine.
Exhaust�turbocharger
B58TU�engine
B58B30M1
Cylinder�head-integrated exhaust�manifold
B58B30O1
Non�cylinder�headintegrated�exhaust�manifold
Steel
27
B58TU�Engine
6.�Fuel�System
6.1.�Fuel�preparation
The�fuel�preparation�has�been�modified�to�meet�the�requirements�of�emission�legislation.�The�high pressure�pump�and�the�injectors�have�been�revised�and�designed�for�a�fuel�injection�pressure�of
350 bar.
Fuel�preparation,�B58TU�engine
Index
1
2
3
4
5
6
7
8
Explanation
Injector
Holding�clamp
Rail�pressure�sensor
Rail
High-pressure�line
High�pressure�pump
Quantity�control�valve
Fuel�feed�line
Strict�cleanliness�must�be�observed�when�carrying�out�any�work�on�the�fuel�system�
28
B58TU�Engine
6.�Fuel�System
6.1.1.�Direct�rail
Mounting�the�injectors
Index
3
4
1
2
5
6
Explanation
Mounting�bolts
Plastic�sleeve
Holding�clamp�with�bayonet�fitting
Rail
Solenoid�valve�injector
Cast�lug
The�solenoid�valve�injectors�are�fastened�to�the�holding�clamp�with�a�bayonet�fitting.�There�is�a�plastic sleeve�between�the�holding�clamp�and�direct�rail.�This�is�not�designed�to�collect�escaping�fuel.�This is�only�used�to�support�a�helium�leakage�test�during�pre-assembly�at�the�factory�in�order�to�check�the tightness.�After�the�initial�assembly,�this�plastic�sleeve�is�of�no�relevance�to�the�engine�operation.�When the�solenoid�valve�injectors�are�reinstalled�or�replaced,�the�plastic�sleeves�are�no�longer�required�and do�not�need�to�be�reinserted.
The�mounting�bolts�of�the�holding�clamp�must�be�replaced�each�time�they�are�released.
29
B58TU�Engine
6.�Fuel�System
The�housing�on�the�solenoid�valve�injectors�is�sensitive�to�excessive�tensile�forces�and�excessive rotational�angles.�When�removing�and�installing�the�solenoid�valve�injectors,�the�procedure�in�the current�repair�instructions�must�be�followed��If�the�solenoid�valve�injectors�are�damaged,�fuel�may�be discharged.
6.1.2.�Solenoid�valve�injector
Measures�at�the�solenoid�valve�injector
The�following�graphic�illustrates�the�differences�between�the�EURO�6b�and�EURO�6c�versions:
30
B58TU�Engine
6.�Fuel�System
EURO�6�measures,�solenoid�valve�injector
Index
C
1
A
B
2
Explanation
Solenoid�valve�injector�HDEV5�Bx8�engine,�EURO�6b
Solenoid�valve�injector�HDEV5�EVO�Bx8�engine,�EURO�6c
Solenoid�valve�injector�HDEV6�Bx8TU�engine,�EURO�6c
Injector�seat
Injection�pattern�and�volumetric�distribution
31
B58TU�Engine
6.�Fuel�System
The�Bx8TU�engines�use�the�HDEV6�solenoid�valve�injector�by�Bosch.�Due�to�the�more�stringent exhaust�gas�emission�regulations�required�to�meet�the�EURO�6c�exhaust�emission�standards, technical�changes�were�again�made�to�the�solenoid�valve�injectors.
Due�to�the�fuel�system�pressure�increase�from�200 bar�to�350 bar,�the�solenoid�valve�injectors�HEDV6 were�optimized�using�suitable�materials�and�coatings.�The�injection�pattern�and�volumetric�distribution have�not�changed�compared�with�the�HDEV5�EVO.
The�repair�instructions�that�are�currently�valid�must�be�carefully�followed �when�removing�and installing�the�injectors�in�Service.�An�excessive�rotational�angle�at�the�injector�shank,�and�excessive tensile�and�compressive�forces�during�removal�and�installation�can�lead�to�damage�and�therefore�leaks in�the�fuel�system.
32
B58TU�Engine
7.�Engine�Electrical�System
7.1.�Digital�Motor�Electronics�(DME)
DME�8�control�unit
The�8th�generation�engine�electronics�form�a�common�control�unit�platform�for�gasoline�and�diesel engines�that�have�been�used�since�modular�engines�were�introduced.�Its�appearance�is�characterized by�a�uniform�housing�and�a�uniform�connector�strip.�The�hardware�inside�has�been�adapted�to the�respective�applications.�The�Bx8TU�engines�have�the�DME�8�engine�electronics�generation.
Depending�on�the�engine�version,�the�Digital�Motor�Electronics�(DME)�will�be�given�a�specific designation.
DME�8.xTyz�(x�=�number�of�cylinders,�Ty�=�vehicle�electrical�system�architecture,�z�=�H�(hybrid))�can�be decoded�as�follows:
• DME�8.4T1�=�B48
• DME�8.4T0.H�=�B48�PHEV
• DME�8.6T0�=�B58
• DME�8.8T0�=�N63
33
B58TU�Engine
7.�Engine�Electrical�System
7.2.�Component�temperature�sensor
B58TU�engine,�component�temperature�sensor
Index
1
Explanation
Component�temperature�sensor
The�B58TU�engine�uses�a�component�temperature�sensor�in�addition�to�the�coolant�temperature sensor�to�control�the�coolant�more�precisely�with�the�heat�management�module.�Except�for�the installation�location,�no�changes�have�been�made�to�the�function�of�the�component�itself.�It�records the�material�temperature�of�the�crankcase�close�to�the�cylinder�head�in�the�area�of�the�6th�cylinder�and forwards�this�to�the�DME�engine�control�unit.�As�a�result,�power,�consumption�and�pollutant�emissions can�be�influenced�even�more�efficiently.
A�variable�temperature�resistance�(negative�temperature�coefficient),�which�covers�a�temperature range�from�-�40°�C�to�150°�C�(-�40°�F�to�302°�F),�has�been�tried�and�tested.�The�temperature�is transferred�to�the�sensor�using�an�elastic�heat�coupler�attached�to�the�outside�of�the�sensor.
34
Download
Advertisement
Key features
Delivers exceptional power and torque for an exhilarating driving experience
Optimized for fuel efficiency without compromising performance
Meets stringent emission standards for environmental sustainability
Features a split cooling system for efficient temperature management
Compact and lightweight design for enhanced agility and responsiveness
Incorporates VANOS technology for precise valve timing and optimized performance
Equipped with a vacuum pump for reliable vacuum supply
Frequently asked questions
The B58TU engine combines impressive power and efficiency, delivering an exhilarating driving experience while optimizing fuel consumption.
The split cooling system ensures optimal temperature management, enhancing engine efficiency and extending component life.
VANOS technology provides precise valve timing, optimizing engine performance and efficiency across a wide range of operating conditions.
The vacuum pump ensures a reliable vacuum supply, supporting various engine functions such as brake assist and emission control systems.