pro
ACTpro MIFARE Readers
ACTpro MF 1030e -
Slimline Proximity Reader
ACTpro MF 1040e -
Proximity Reader
ACTpro MF 1050e -
PIN & Proximity Reader
ACTpro MF 1030PM -
Panel Mount Proximity Reader
Installation Manual
ACTpro MIFARE Readers Installation Manual
Contents
Page No.
Specifications Table ................................................................................ 3
Product Description ................................................................................ 4
Reader Connections 1040e/1050e .......................................................... 4
Reader Connections 1030e ..................................................................... 5
CAT 5/6 Colour Code .............................................................................. 5
Clock & Data Entry and Exit Reader Wiring Diagrams ............................ 6
Wiegand Entry and Exit Reader Wiring Diagrams ................................... 7
Reader Configuration .............................................................................. 8
Reader Reprogramming .......................................................................... 9
1050e Backlight Operation .................................................................... 10
Power On Beep Codes .......................................................................... 10
1030PM Connections to Controllers/Doorstations ............................... 11
1030PM Mounting Diagram & Instructions ........................................... 12
1040e/1050e Surface Mounting Diagram ............................................. 13
1030e Mounting Diagram ...................................................................... 13
1040e/1050e Flush Mounting Diagram ................................................. 14
1040e/1050e Flush Mounting to UK Pattress Box Diagram ................. 15
Product Code
ACTpro MIFARE 1030e
ACTpro MIFARE 1030PM
ACTpro MIFARE 1040e
ACTpro MIFARE 1050e
Description
MIFARE Classic Proximity reader, mullion mount
MIFARE Classic Proximity reader, panel mount
MIFARE Classic Proximity reader, surface / flush
MIFARE Classic Prox & PIN reader, surface / flush
2
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
ACTpro MIFARE Readers Installation Manual
Specifications Table
Connections
Dimensions
W x H x D
Mounting
Weight
Power Supply
Selectable sector,serial & reverse serial
Current
Consumption
Typical
Current
Consumption
(Peak)
Operating
Temperature
Transmit
Frequency
Keypad
Environmental
Rating
Cable
Distance
Output
Formats
Indoor &
Outdoor
PIN or Prox
MIFARE 1030e
Pigtail
MIFARE 1030PM
Terminal Block
MIFARE 1040e
Terminal Block
MIFARE 1050e
Terminal Block
37 x 120 x 15mm 63 x 58 x 23mm 95 x 128 x 19mm 95 x 128 x 21mm
Mullion
150g
12Vdc-24Vdc
Yes
30mA
1 30mA
-10°C/50°C
13.56MHz
No
IP67
100 m
Wiegand or
Clock & Data
Yes
Prox
Panel
65g
12Vdc-24Vdc
Yes
30mA
70mA
-10°C/50°C
13.56MHz
No
IP67
100 m
Wiegand or
Clock & Data
Yes
Prox
Flush or Surface
142g
12Vdc-24Vdc
Yes
70mA
140mA
-10°C/50°C
13.56MHz
No
IP67
100 m
Wiegand or
Clock & Data
Yes
Prox
Flush or Surface
155g
12Vdc-24Vdc
Yes
70mA
140mA
-10°C/50°C
13.56MHz
Yes
IP67
100 m
Wiegand or
Clock & Data
Yes
PIN & Prox
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
3
ACTpro MIFARE Readers Installation Manual
Product Description
•
•
•
•
•
ACT MIFARE classic readers support all ACT MIFARE cards and fobs.
They can be confi gured to read serial, reverse serial or sector data from any third party MIFARE Classic card.
Compatible with ACT MIFARE cards and fobs
Confi gured to read ACT Sector data, Serial Number or reverse serial number
Confi gured to read Sector data form any MIFARE Classic card
(Read key required)
Confi gured for Wiegand or Clock&Data output
Confi gurable backlight (1050e only)
Reader Connections -
ACTpro MIFARE 1040e/1050e
Sector/Serial
Operation Jumper
+12V DC
Data
CLOCK
SENSE
BUZZ
0V
RED
GREEN
A
B
4
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
ACTpro MIFARE Readers Installation Manual
Reader Connections -
ACTpro MIFARE 1030e
ACTpro MIFARE 1030e is supplied with 3m pigtail cable.
SENSE (White)
CLOCK/D1 (Green)
DATA/D0 (Blue)
+12V (Red)
0V/GND (Black)
RED LED (Brown)
GREEN LED (Yellow)
(Orange)
(Purple)
}
Programming
Sector/Serial
ISP (Grey) - Unused
CAT 5/6 Colour Code
The following is suggested colour coding if using CAT5 or CAT6 cabling.
Reader
Output
Sense
Clock / D1
Data / D0
+12V
(0V) GND
Red LED
Green LED
Orange &
Purple
ISP
Colour
White/Green
Green
Blue
Orange
White/Orange
Brown
White/Brown
Programming Sector/
Serial
Grey (Unused)
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
5
ACTpro MIFARE Readers Installation Manual
Clock & Data Entry Reader - Wiring
BUZZER INPUT
(Not available on 1030e)
SENSE (White)
CLOCK / D1 (Green)
DATA / D0 (Blue)
+12V (Red)
OV / GND (Black)
RED (Brown)
GREEN (Yellow)
Clock & Data Exit Reader - Wiring
DO NOT CONNECT SENSE (White cable)
BUZZER INPUT
(Not available on 1030e)
SENSE (White)
CLOCK / D1 (Green)
DATA / D0 (Blue)
+12V (Red)
OV / GND (Black)
RED (Brown)
GREEN (Yellow)
6
NB: Illustrations apply to all MIFARE readers
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
ACTpro MIFARE Readers Installation Manual
WIEGAND Entry Reader - Wiring
BUZZER INPUT
(Not available on 1030e)
SENSE
CLOCK / D1 (Green)
DATA / D0 (Blue)
+12V (Red)
OV / GND (Black, White)
RED (Brown)
GREEN (Yellow)
IMPORTANT: To put ACT readers into wiegand mode connect the SENSE on the reader to 0V/GND.
WIEGAND Exit Reader - Wiring
BUZZER INPUT
(Not available on 1030e)
SENSE (Blue)
CLOCK / D1 (Green)
DATA / D0
+12V (Red)
OV / GND (Black, White)
RED (Brown)
GREEN (Yellow)
IMPORTANT: To put ACT readers into wiegand mode connect the SENSE on the reader to 0V/GND PIN and
DATA/D0 to the SENSE PIN on the controller.
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
7
8
ACTpro MIFARE Readers Installation Manual
Reader Configuration
Operation: ACTpro MIFARE 1030PM / 1040e / 1050e
ACTpro MIFARE readers can operate in sector, serial or reverse serial mode which is selectable via a jumper. To change the operation mode power down the reader, change the jumper for the desired operation and re-apply power.
Sector
Connect Pins 1&2
1
2
3
Serial
1
2
3
Connect Pins 2&3
Reverse
Serial
1
2
3
Do NOT connect Jumper
Operation: ACTpro MIFARE 1030e
The operation of the ACTpro MIFARE 1030e is selectable via cable configuration. To change the operation power down the reader, change the Orange and Purple cable for the desired operation and re-apply power.
Colour
Orange
Purple
Sector
0V
0V
Serial
0V
Not Connected
Reverse Serial
Not Connected
0V
Sector Reader
The default sector reader operation reads a numbers encoded into
Sector 1 of the MIFARE cards and fobs. The ACT MIFARE readers can be programmed to read any specified sector data. See section on reader re-programming.
Serial and Reverse Serial Reader
When in Serial or reverse serial mode the MIFARE card serial number
(CSN) is read by the reader.
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
ACTpro MIFARE Readers Installation Manual
Reader Re-programming
The ACTpro MIFARE readers will ship from the factory pre-configured to read ACT MIFARE cards and fobs. The ACT pro MIFARE reader can also be reconfigured for serial or reverse-serial by repositioning the jumpers.
(See section on reader configuration)
On sites with an existing installation of MIFARE cards, it may be necessary to re-program MIFARE readers so that data on the existing MIFARE cards can be read. The ACTpro MIFARE readers are re-programmed using a programming card.
The programming card can be generated on site using ACTenterprise software and an ACTpro USB reader (ACTinstall->Advanced Setup
->card configuration->MIFARE format). You will require the following information on how the existing cards are encoded before generating the programming card: Data Format, Data Orientation, Start and End
Byte Position and Read/Write Keys.
To re-program an ACTpro MIFARE reader the programming card must be presented to the reader after power up and while the LED is Red.
The ACTpro MIFARE will acknowledge the re-programming by playing an ascending note tune. (Configuration is held in non-volatile memory)
Readers that have been re-programmed may be reset to read ACT issued MIFARE cards and fobs with an ACT Default Programming Card.
ACTpro MIFARE readers that have been programmed to read non ACT
MIFARE cards and fobs will play a series of ascending notes after being powered up in addition to the standard beep codes, this is to indicate that it no longer reads the MIFARE cards and fobs issued by ACT.
Please see the “Application for an ACTpro MIFARE reader programming card” document for details on obtaining a programming card.
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
9
10
ACTpro MIFARE Readers Installation Manual
Backlight Operation - ACTpro MIFARE 1050e
The ACTpro MIFARE 1050e has backlight illumination of the keypad. The default operation is for the illumination to be switched on. During installation the back light operation may be switched off or changed to automatic. In automatic mode the keypad is illuminated for 20 seconds on a key press or when a card is presented to the reader.
To change the backlight operation: Firstly power up the reader, the LED on the top right hand side will cycle through green, blue and red and back to blue, while the
LED is red enter the code below for the required operation. The code must be completely entered while the LED is red.
• Always on (Default): X014000
• Always Off:
• Automatic:
X014001
X014008
Note: the backlight operation for the ACTpro MIFARE 1030PM is controlled by jumpers marked LED.
Buzzer Operation
The Internal buzzer is activated by applying 0V to the Buzz PIN. The buzzer activates 4 seconds after the 0V is applied and sounds continuously until the 0V is removed (External Buzzer Control not available on the ACTpro MIFARE 1030) reader.
Power On Beep Codes
The Output Data Format and the Sector/Serial Operation of the reader can be determined by the beeps generated by the reader after power is applied. The reader will generate two sets of beeps, the first indicating the Output Data Format and the second set of beeps indicating Sector or Serial Operation. The first set of beeps will occur while the LED is Green, the second set of beeps occur half a second later while the LED is Blue.
First Beep Set
Second Beep Set
Double Beep
Single Beep
Triple Beep
Double Beep
Single Beep
Sector Reader
Serial Reader
Serial Reader (byte reverse)
Clock & Data Output
Wiegand 37 bit Output
Note : If the reader has been re-programmed (see next page), then a series of notes is played after the Second Beep Set, this indicates that the default programming to read ACT MIFARE cards has been changed.
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
ACTpro MIFARE Readers Installation Manual
ACTpro MIFARE 1030PM
Mounting Diagram
Mounting Instructions
1. Place the VR screen printed perspex over the four studs on the back of the audio entry panel.
2. Place the ACTpro MIFARE panel mount reader over the four studs.
3. Use the four M3 washers and nuts supplied with the product to secure the reader to the audio entry panel.
4. Use the wiring diagram below to connect the reader to the controller
5. When wiring is complete, place the front cover back onto the audio entry
panel.
6. Apply power to the controller and test the reader with a card or fob.
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
11
12
ACTpro MIFARE Readers Installation Manual
ACTpro 1030PM MIFARE Panel Mount reader connections to the ACTpro
Door Controllers & Door Stations
Jumper Pins 1 + 2:
Sector operation
Jumper Pins 2 + 3:
Serial operation
No Jumper:
Byte reversed serial operation
Sector Mode
Serial Mode
{
{ 1
2
3
ON LED OFF
+12/24V
DATA
CLOCK
SENSE
0V
RED L
GREEN L
BUZZ
LED Control
The standby LED on the front of the reader can be configured using the link wire. When the link wire is connected between LED and OFF, the blue LED on the front of the reader will remain off while in standby. It will turn green on access granted and red on access denied
When the link wire is connected between LED and ON, the blue LED on the front of the reader will remain on while in standby. It will turn green on access granted and red on access denied.
Wiring for Clock & Data /
Wiegand Reader
The standard wiring colours for ACTpro
MIFARE readers are shown across.
Readers should be a maximum of 100m when powered from +12V.
White
Green
Blue
Red
Black
Brown
Yellow
ORANGE
SENSE
CLOCK & DATA 1
DATA / DATA 0
+12V
0V
RED LED
GREEN LED
(BUZZER Ctrl)
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
ACTpro 1030PM MIFARE Panel Mount reader connections to the ACTpro
Door Controllers & Door Stations
ACTpro MIFARE Readers Installation Manual
ACTpro MIFARE 1040e/1050e
Surface Mount Diagram
Security screw supplied with the unit
Place the cap onto the unit and push firmly in place
The surface mount collar is mounted on the wall using the fixing kit supplied in the box.
Place the reader / keypad onto the surface mount collar and clip down into place. Use the security screw supplied to attach the unit to the surface mount collar.
ACTpro 1030e MIFARE
Mounting Diagram
Screw unit to the surface.
Place caps on to the unit and push firmly into place.
Screw unit to the surface.
Place caps onto the unit and push firmly into place
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
13
ACTpro MIFARE Readers Installation Manual
ACTpro MIFARE 1040e/1050e
Flush Mount Diagram
14
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
ACTpro MIFARE Readers Installation Manual
ACTpro MIFARE 1040e/1050e
Flush Mounting to UK Pattress Box
Copyright © 2016 Access Control Technology Ltd. Part No.18-00102 Issue 1
15
Access Control Technology Ltd. reserve the right to change the contents of this manual and the system it applies to without prior notice.
While every effort has been taken by ACT to ensure the accuracy of the information contained within this document, ACT assumes no responsibility for any errors or omissions. No liability is assumed for damages resulting from the use of information contained within this document.
Ireland Office
Unit C1, South City Business Centre,
Tallaght, Dublin, D24 PN28, Ireland
United Kingdom Office
601 Birchwood One, Dewhurst Road,
Birchwood, Warrington, WA3 7GB, UK
Ireland: +353 (0)1 466 2570
UK: +44 (0)161 236 9488
Email: [email protected]
www.act.eu
www.act-access.com (USA)
Copyright © 2016 Access Control Technology Ltd. Part No. 18-00106 Issue 0
