advertisement
Astra Wash19Pix
19x40W RGBW moving wash light with
4°-54° zoom, pixel control and pixel ring
REV.01-04/21
USER MANUAL
English version
Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively applicable national accident prevention rules and regulations.
Features, specifications and appearance are subject to change without notice. Music & Lights S.r.l. and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the official
PROLIGHTS distributors of your territory ( https://www.prolights.it/sales_network.html
).
Scanning the below QR Code , you will access the download area of the product page, where you can find a broad set of always updated technical documentation: specifications, user manual, technical drawings, photometrics, personalities, fixture firmware updates.
Visit the download area of the product page
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its affiliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY.
INDEX
5 - CONNECTION TO THE MAINS SUPPLY 08
CONNECT AND DISCONNECT POWER FROM THE PRODUCT .................................. 08
CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 10
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 10
CONSTRUCTION OF THE DMX TERMINATION ........................................................... 11
17 - ACCESSORIES INSTALLATION 33
MAINTENANCE AND CLEANING THE PRODUCT ........................................................ 35
PROLIGHTS - Astra Wash19Pix 01
02
0.3 m
SAFETY INFORMATION
WARNING!
• Please read carefully the instruction reported in this section before installing, power ing, operating or servicing the product and observe the indications also for its future handling.
This unit is not for household use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualified electrical installer.
• Use only AC supplies 100-240V 50-60 Hz, the fixture must be electrically connected to ground (earth).
• Select the cable cross section in according with the maximum current draw of the product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC power before servicing.
• Ensure that the fixture is electrically connected to ground (earth). And use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault (earth-fault) protection.
• Before using the fixture, check that all power distribution equipment and cables are in perfect condition and rated for the current requirements of all connected devices.
• Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other components are damaged, defective, deformed or showing signs of overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the fixture above ground level, secure it against failure of primary attachments by attaching a safety cable that is approved as a safety attachment for the weight of the fixture to the attachment point on the main frame of the product. ln case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the fixture is securely fastened to a loadbearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or screws are turned fully, and secured with a suitable safety cable.
Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are at least 0.3 meters (0.98 ft) from the lens of the projector.
PROLIGHTS - Astra Wash19Pix
Max operating ambient temperature (Ta)
• Do not operate the fixture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
Minimum operating ambient temperature (Ta)
• Do not operate the fixture if the ambient temperature (Ta) is below -10 °C (14 °F).
Protection from burns and fire
• The exterior of the fixture becomes hot during use. Avoid contact by persons and materials.
• Ensure that there is free and unobstructed airflow around the fixture.
• Keep flammable materials well away from the fixture.
• Do not expose the front glass to sunlight or any other strong light source from any an gle. Lenses can focus the sun’s rays inside the fixture, creating a potential fire hazard.
• Do not attempt to bypass thermostatic switches or fuses.
Indoor use
• This product is designed for indoor and dry environments.
• Do not use in wet location and do not expose the fixture to rain or moisture.
• Never use the fixture in places subject to vibrations or bumps.
• Make certain that no inflammable liquids, water or metal objects enter the fixture.
• Excessive dust, smoke fluid, and particle build up degrades performance, causes overheating and will damage the fixture.
• Damages caused by inadequate cleaning or maintenance are not covered by the product warranty.
Light collimation optical system*
• This product contains internal light collimation opticsl system. Avoid to expose the optical system to any intense source of light (including sunlight) from any angle.
Temperature of the external surface
• The surface of the fixture can reach up to 70 °C (158 °F) during operation. Avoid contact with people and materials.
Lamp*
The fitting mounts a high-pressure lamp that needs an external ignitor. This ignitor is fitted onto the apparatus.
1. Carefully read the “operating instructions” provided by the lamp and ignitor manufacturer.
2. Immediately replace the lamp if damaged or deformed by heat.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identified in the category of Risk Group 2 according to EN 62471.
Radio receiver*
• This product contains a radio receiver and/or transmitter:
• Maximum output power: 17 dBm.
• Frequency band: 2.4 GHz.
PROLIGHTS - Astra Wash19Pix 03
Maintenance
• Warning! Disconnect the fixture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners are permitted to open the fixture.
• Users may carry out external cleaning, following the warnings and instructions provided, but any service operation not described in this manual must be referred to a qualified service technician.
• Important! Excessive dust, smoke fluid, and particle build up degrades performance, causes overheating and will damage the fixture. Damages caused by inadequate cleaning or maintenance is not covered by the product warranty.
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes and skin.
• During Installation, operation and maintenance, be prepared for the fixture to light and move suddenly when connected to power.
• The device should be positioned so that prolonged staring into the luminaire at a distance closer than 2.687 m (8.815 ft) is not expected.
Minimun distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
2.687 m
8.815 ft
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment.
• (WEEE). To preserve the environment please dispose/ recycle this product at the end of its life according to the local regulation.
The product contains a lithium ion battery
• Don't throw the unit into the garbage at the end of its lifetime.
• Make sure to dispose according to your local ordinances and/or regulations, to avoid polluting the environment!
• The packaging is recyclable and can be disposed.
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD);
• 2014/30/EU - Electromagnetic Compatibility (EMC);
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS);
• 2014/53/EU - Radio Equipment Directive (RED).
04 PROLIGHTS - Astra Wash19Pix
1 - PACKAGING
PACKAGE CONTENT
• 1x ASTRAWASH19PIX;
• 1x 1,5 meters power cable (SCHUKO plug - SEETRONIC IP65 power connector);
• 2x OS24;
• User Manual.
OPTIONAL ACCESSORIES
• FCLASTRAW19PIX: flight case for 4 pcs of ASTRAWASH19PIX;
• ASTRAW19PEC: egg crate for ASTRAWASH19PIX;
• WSPBF2500G5: proBox F-2500 G5 transmitter, 1024Ch 90-250VAC, 19;
• WSBBF2G5: blackBoxF-2 G5 transmitter, 2,45GHz & 5.2/5,8 GHz, DMX/RDM, 1024Ch;
• WSBBF1G5: blackBox F-1 G5 transmitter, 2,45GHz & 5.2/5,8 GHz, DMX/RDM, 512Ch;
• MICROF1G5: micro F-1 G5 transmitter, int. omni antenna 2dBi, 2,45GHz. 512Ch, 12VDC, Batt.;
• OS24: quick-lock omega bracket;
• C6002: slim aluminium clamp, 200 kg loading, 48-51 mm tubes, M10 bolt;
• RSR0630A/B: steel security cable for hanging bodies, inox steel shackle, L=60 cm, silver/black;
• UPBOX2: firmware uploader kit, USB IN, 3-pin XLR DMX OUT.
2 - TECHNICAL DRAWING
514 mm [20.2 in]
459 mm [18.1 in] 485 mm* [19.1 in]
410 mm
[16.1 in]
* The measure includes the zoom.
Weight: 17.4 kg - 38.36 lbs
250 mm
[9.8 in]
PROLIGHTS - Astra Wash19Pix
308 mm
[12.1 in]
Fig. 01
05
3 - PAN AND TILT LOCK
PAN Mechanism lock and release
TILT Mechanism lock and release
90°
90°
90°
90°
06 PROLIGHTS - Astra Wash19Pix
45°
45°
45°
45°
45°
45°
Fig. 02
4 - INSTALLATION
MOUNTING
Check that the supporting structure can safely bear the weight of all installed fixtures, clamps, cables, auxiliary equipment, etc. and complies with locally applicable regulations.
When suspending the fixture above ground level, secure it against failure of primary attachments by attaching a safety wire that is approved as a safety attachment for the weight of the fixture to an anchor point on the product main frame.
Do not use removable parts or weak anchors for secondary attachment.
Warning! When clamping the fixture to a truss or other structure at any angle, use clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
C6002 clamp
RSR0630A/B
Steel security cable
OSIP
108 mm [4.3 in]
94 mm
[3.7 in]
Dimensions are in mm / in - Fig.03
PROLIGHTS - Astra Wash19Pix 07
5 - CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the fixture must be earthed!
The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
If you need to install a power plug on the power cable to allow connection to power outlets, install a grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts about proper installation, consult a qualified electrician.
The max power consumption is 620W.
Core (EU)
Brown
Blue
Yellow+green
Core (US)
Black
White
Green
Connection
Live
Neutral
Earth
Plug terminal marking
L
N
6 - START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT
To apply and disconnect power to the product:
• Check that the product is installed and secured as indicated in the Safety Informations, and that personal safety will not be put at risk when the fixture lights up.
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).
• The product is then ready for its operations and can be controlled through the available input sig nals on board.
• To disconnect power from the product, disconnect the Mains from the socket.
08 PROLIGHTS - Astra Wash19Pix
7 - PRODUCT OVERVIEW
1. TILT Mechanism lock and release;
2. PAN Mechanism lock and release;
3. SAFETY EYE to attach safety cable;
4. USER INTERFACE with display and buttons for access to the control panel functions;
5. ANTENNA of Wireless DMX Receiver internal module.
6. ETHERCON CONNECTORS IN / OUT signal;
7. DMX IN (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C;
8. DMX OUT (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C;
9. POWER IN: for connection to the Mains 100-240V~/50-60Hz;
10. POWER OUT: power output for connection of multiple units in series;
11. MAIN FUSE HOLDER: replace a burnt-out fuse by one of the same type only (T8A 250V).
9
1 2 3 4 5 6 6 7
PROLIGHTS - Astra Wash19Pix
8 10 11
Fig 04
09
8 - DMX CONNECTION
CONNECTION OF THE CONTROL SIGNAL: DMX LINE
The product has XLR sockets for DMX input and output.
The default pin-out on both socket is as the following diagram:
DMX - INPUT
XLR plug
Pin1 : GND - Shield
Pin2 : - Signal
Pin3 : + Signal
Pin4 : N/C
Pin5 : N/C
DMX - OUTPUT
XLR socket
Fig. 05
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION
Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit control data reliably over long runs. 24 AWG cable is suitable for runs up to 300 meters (1000 ft).
Heavier gauge cable and/or an amplifier is recommended for longer runs.
To split the data link into branches, use splitter-amplifiers in the connection line.
Do not overload the link. Up to 32 devices may be connected on a serial link.
CONNECTION DAISY CHAIN
Connect the DMX data output from the DMX source to the product DMX input (male connector XLR) socket.
Run the data link from the product XLR output (female connector XLR) socket to the DMX input of the next fixture.
Terminate the data link by connecting a 120 Ohm signal termination. If a splitter is used, terminate each branch of the link.
Install a DMX termination plug on the last fixture on the link.
CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω impedance and low capacity.
The following diagram shows the connection mode:
DMX Address: 33 DMX Address: 39 DMX Address: 45 DMX Address: 51
. . . . . . . . . . . .
. . . . . . . . . . . .
10
DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT
DMX512 Controller
Fig. 06 - Example 6 DMX channels configuration
PROLIGHTS - Astra Wash19Pix
CONSTRUCTION OF THE DMX TERMINATION
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the male XLR connector, as shown in figure.
4
Example:
5 pin XLR connector
Fig. 07
DMX ADDRESSING
In order to start controlling the product via DMX, the first step is to select a DMX address, also known as the start channel, this is the first channel used to receive instructions from a DMX controller. If you wish to control the product individually, it is necessary to assign a different starting address channel to each fixture.
The number of channels occupied from the product depends on the DMX mode selected, so always verify the DMX Mode in the MENU before start addressing.
If you assign two fixtures the same address, they will be executing the same behaviour. Selecting the same address to multiple fixtures can be useful for diagnostic purposes and symmetrical control.
DMX addressing is limited to make it impossible to set the DMX address so high that you are left without enough control channels for the product.
To set the fixture’s DMX address:
1. Press ENTER to open the main menu.
2. Reach the addressing menu, then select the DMX ADDRESS settings.
3. Select the address from 1 to 512 using the navigation arrows/buttons and confirm by pressing
ENTER.
4. Press Menu to exit and return to the Home screen.
ETHERNET CONNECTION
The products is provided with two 8-pin RJ-45 sockets for Ethernet input/output for a simple daisy chain connection to the network.
The product can be controlled with ArtNet (or others available) communication protocol.
Use a network cable category 5 (with four “twisted” wire pairs) and standard RJ-45 plugs.
ETHERNET OPERATION
Please refer to the section MENU STRUCTURE contained in this document for detailed informations about the parameters of setting on the fixture (Protocol, Net, Subnet, Universe, Start Channel and IP
Address, Ethernet to DMX No/Yes).
• About the IP addresses is recommended to set 002.xxx.xxx.xxx or 010.xxx.xxx.xxx.
• The submask net is fixed at 255.0.0.0.
PROLIGHTS - Astra Wash19Pix 11
12
ETHERNET TO DMX OPERATIONS
Please refer to the section MENU STRUCTURE contained in this document for detailed informations
This function allow a product receiving an ethernet signal protocol to re-transmit the incoming signal onto a wired DMX line through its onboard XLR-out connector.
• An Ethernet protocol (Artnet, sACN or others available) has to be enabled from Ethernet menu at first fixture. Please make sure that wireless receiver is switched to OFF if you use Ethernet comunication.
• Enable the option Ethernet To DMX from the Ethernet menu at the first product (connected to the
Ethernet) in the signal chain, next products have standard DMX setting.
• Connect the Ethernet input of the first product in the data chain with the network. Connect the
DMX output of this product with the input of the next product until all products are connected to the DMX chain.
• Caution: At the last product, the DMX chain has to be terminated with a terminator. Solder a 120 Ω resistor between Signal (–) and Signal (+) into a XLR-plug and connect it in the DMX-output of the last product.
OPERATION AS A WIRELESS TRANSMITTER
ASTRAWASH19PIX can be used as wireless transmitter to transmit DMX signal to different wireless receivers. To use ASTRAWASH19PIX as wireless transmitter, please follow the procedure below:
1. Push ENTER button untill you show CONNECT on display, then press ENTER button to confirm.
2. Use UP/DOWN buttons for select WIRELESS, then press ENTER to confirm.
3. Push ENTER button on WDMX ON/OFF function and enable it to ON.
4. Select WDMX mode and set it on Transmitter (please note that WDMX mode will be available only if WDMX ON/OFF is set to ON).
5. Ensure that the receiver units are not connected to any other transmitter. Please refer to "Reset the receiver" paragraph.
6. Enable TX LINK to ON to link transmitter to receivers (please note that TX LINK will be available only if WDMX mode is set to Transmitter).
• The transmitter scans for all unlinked receivers for a period of about 5 seconds.
• If the connection fails, check the position of the receiver.
• The wireless icon on the receiver display indicates the received signal strength.
Unlinking the transmitter
Follow the procedure below to unlink the transmitter from all receivers connected with the unit.
1. Push ENTER button untill you show CONNECT on display, then press ENTER button to confirm.
2. Use UP/DOWN buttons for select Wireless, then press ENTER to confirm.
3. Enable TX UNLINK to ON 8 (please note that TX UNLINK will be available only if WDMX mode is set to Transmitter).
• All connected receivers will be unlinked.
IN TO WDMX
This function enable or disable the transmission throught wireless of the DMX signal from the transmitter side to the receiver.
Any incoming signal (ArtNet, sACN or DMX) is retransmitted throught wireless.
If the ASTRAWASH19PIX protocol selected is ArtNet / sACN, the WDMX module will retransmit the
DMX values contained in the ArtNet / sACN signal received from the ASTRAWASH19PIX.
NOTE : Artnet and sACN have higher priority on DMX if they are connected to transmitter.
PROLIGHTS - Astra Wash19Pix
OPERATION AS A WIRELESS RECEIVER
ASTRAWASH19PIX can be used as wireless receiver connected to a wireless transmitter.
To use ASTRAWASH19PIX as wireless receiver, please follow the procedure below:
1. Push ENTER button untill you show CONNECT on display, then press ENTER button to confirm.
2. Use UP/DOWN buttons for select Wireless, then press ENTER to confirm.
3. Push ENTER button on WDMX ON/OFF function and enable it to ON.
4. Select WDMX mode and set it on Receiver (please note that WDMX mode will be available only if
WDMX ON/OFF is set to ON).
5. Enable RX RESET to ON to reset the receiver (please note that RX RESET will be available only if
WDMX mode is set to Receiver).
6. On the transmitter, enable TX LINK to ON to link transmitter to the receivers.
7. If the connection is successful and DMX input is available the display the display on the receiver unit will shows the DMX address. If DMX signal is not available, the display will shows "No signal" but keeps the transmitter linked.
8. If the connection fails, check the position of the receiver.
9. The wireless icon on the receiver display indicates the received signal strength.
Reset the receiver
Follow the procedure below to reset the receiver.
1. Push MENU button untill you show CONNECT on display, then press ENTER button to confirm.
2. Use UP/DOWN buttons for select Wireless, then press ENTER to confirm.
3. Enable RX RESET to ON.
• The wireless icon on the receiver display indicates the received signal strength.
WDMX TO DMX (RX)
This function enable or disable the retransmission of the wireless DMX signal received throught the
DMX port on the receiver side.
PROLIGHTS - Astra Wash19Pix 13
9 - CONTROL PANEL
The product has a display and buttons for access to the control panel functions.
Fig. 08
14
DISPLAY AND BUTTONS LAYOUT
The product has a display and buttons for access to the control panel functions:
4
1
5
3
2
2
3
1
• Browse upwards through the menu list and increases the numeric value displayed.
• Return to the top level.
• Browse downwards through the menu list and decreases the numeric value displayed.
4
5
• Commute from units, tens, hundred in the menu.
• Used to access the menu tree or to return a previous menu window.
• To switch on the display throught the battery.
• LED indicator for Wireless dmx (color red and green).
• LED indicator for Ethernet network.(color orange).
PROLIGHTS - Astra Wash19Pix
10 - MENU STRUCTURE
The following chart describes the MENU tree of the product, the terms shown in BOLD indicates the default settings.
MENU
1 CONNECT ADDRESS
DMX MODE
WIRELESS
FIXTURE
PIXELS
FIXTURE
PIXELS
WDMX ON/OFF
WDMX MODE
TX LINK
TX UNLINK
RX RESET
IN TO WDMX (TX)
WDMX TO DMX (RX)
DMX / WDMX sACN
001 -512
001 -512
ARTNET 001 -512
FOLLOW FIXTURE 001 -512
DMX / WDMX sACN
ARTNET
001 -512
001 -512
001 -512
001 -512 sACN +
KLINGNET
ARTNET +
KLINGNET
BASIC
001 -512
FX
STANDARD
EXTENDED
OFF
RING
PIXELS
ON/ OFF
TRANSMITTER/
RECEIVER
Set DMX chart for Main Fixture.
Set DMX chart for Pixel Fixture.
ON/
ON/
ON/
OFF
OFF
OFF
OFF
MAIN FIXTURE
TO WDMX
PIXEL ENGINE TO
WDMX
ON /OFF
Enable/Disable the wireless card.
Allows to choose whether to set the wireless on the Transmitter or
Receiver.
WDMX mode is unlocked only if
WDMX ON / OFF is ON.
TX link unlock when the unit is set as a transmitter..
Disconnect the transmitter from all receivers. TX unlink unlocks only if WDMX mode is on transmitter
Total reset of the receiver.
RX reset unlocks only if WDMX mode is receiver.
Enable/Disable the transmission of the DMX values via wdmx.
Main Fixture to WDMX: transmitt main fixture DMX values
Pixel Engine to WDMX: transmitt pixel engine dmx values
Enable/Disable the retransmission of the DMX from the receiver to the other units connected by cable to the receiver itself
PROLIGHTS - Astra Wash19Pix 15
16
2 SETUP
ETHERNET
SETTING
SCREEN
ARTNET SETTINGS IP ADDRESS
NET sACN SETTINGS
SUBNET
UNIVERSE
IP ADDRESS
UNIVERSE
MERGE MODE
ETHERNET TO DMX ON
KLINGNET
BACKLIGHT
FLIP DISPLAY
KEY LOCK
OFF
ON
OFF
ON
10 s
20 s
30 s
ON
OFF
AUTO
ON
OFF
Set IP address of the fixture.
Set Net for ArtNet protocol.
Set Subnet for ArtNet protocol.
Set Universe for ArtNet protocol.
Set IP address of the fixture.
Set Universe for sACN protocol.
OFF /HTP/LTP Set Merge Mode for sACN protocol.
Enable / Disable DMX retrasmission from sACN/
ArtNet signal to DMX out port.
Enable / Disable Klingnet functionality for sACN / ArtNet protocols.
Allows you to select the timing after that display will switch automatically off when unactive.
Allows you to rotate the display by 180°.
Allows you lock the buttons on the control panel by a password. Press following combinations (password) in order to access to the user menu : UP,
DOWN, UP, DOWN.
Allows you to reverse Pan movement.
Allows you to reverse Tilt movement.
MOVEMENT PAN REVERSE
TILT REVERSE
ON
OFF
ON
PAN/TILT
FEEDBACK
PAN/TILT MODE
HOME POSITION
CUSTOM P DEGREE 0°
...
315°
CUSTOM T DEGREE 0%
...
100%
OFF
ON
OFF
SLOW
MEDIUM
FAST
SYNC
STANDARD
CUSTOM
To activate / deactivate the reading of the feedbacks given by the encoders.
To choose the horizontal/vertical movement speed. SYNC mode will sync movement speed with the whole ASTRA-
WASH familiy fixtures.
To choose the home position.
To choose pan values in case of
Custom position.
To choose tilt values in case of
Custom position.
PROLIGHTS - Astra Wash19Pix
3 ADVANCED
FIXTURE
SETTINGS
RESET
FAN MODE
WHITE CALIBRA-
TION
DMX FAULT
STATUS LED
ZOOM MODE
DIMMER CURVE
DIMMER SPEED
LED FREQUENCY
INVERT MAPPING
INVERT ZOOM
TRANSFER
CONFIGURATION
AUTO
SILENT
HIGH
OFF
STUDIO
8000K
HOLD
SLOW
600Hz
1200Hz
2000Hz
4000Hz
6000Hz
25KHz
50KHz
ON
OFF
ON
OFF
WITHOUT DMX
ADDRESS
WITH DMX
ADDRESS
BLACKOUT
ON
OFF
STANDARD
PIXELS
LINEAR
S-CURVE
SQUARE LAW
INV. SQUARE LAW
AUTO
FAST
MEDIUM
ALL
PAN & TILT
ZOOM
PROLIGHTS - Astra Wash19Pix
Select Fan behaviour.
Manufacturer calibration to grant performance and color consistency.
To choose the behaviour of fix ture in case of dmx signal lost.
To turn the status LEDs on the front panel on or off.
Select zoom mode.
Select different curve behaviour of dimmer
Linear dimmer behaviour.
Dimmer curve adding long fade.
Dimmer curve adding medium fade.
Dimmer curve adding little fade.
Select PWM frequency.
Invert mapping for Pixel fixture.
Invert zoom values.
To transfer the same menu settings of one fixtures to all the other in the daisy chain, including or not the dmx address.
To reset these functions.
17
18
CALIBRATION
MANUAL
CONTROL
PASSWORD
PAN
TILT
...
PAN
...
BASIC RELOAD
4 INFORMATION
RELOAD
DEFAULT
FIXTURE TIME
ALL RELOAD
FIXTURE HOURS
CURRENT HOURS
ON
OFF
ON
OFF
TOTAL
PARTIAL
TOTAL
PARTIAL
SOURCE HOURS TOTAL
PARTIAL
POWER ON CYCLE TOTAL
PARTIAL
MAINTENANCE
TIME
ELAPSED TIME
ALERT PERIOD
TEMPERATURE NEAR SOURCE
TEMP, DRIVER PCB
TEMP, LED PCB
TEMP,…
FANS SPEED NEAR SOURCE
FAN, BASE FAN,…
WIRELESS
QUALITY
CHANNEL
VALUE
ERROR
MESSAGE
FIXTURE
MODEL
RDM UID
SOFTWARE
VERSION
PAN...
PAN, TILT...
XXXXXXXXXX
(READ AND RESET)
1U01 V1.0.00...
For the calibration of these functions.
050 password for user reset.
For manual control of the unit.
050 password for user reset.
(ONLY READ) To check the total working hours of the unit.
(READ AND
RESET)
(ONLY READ) To check the current working hours of the unit.
(READ AND
RESET)
(ONLY READ) To see the total operating hours of the LED source.
(READ AND
RESET)
(ONLY READ) To see the power cycles of the machine.
(READ AND
RESET)
To choose and reset unit maintenance warning hours.
10 - 300
To see the unit temperature.
To see the speed of the fans.
To check the wireless quality.
To see the dmx value of those channels.
To see any error messages.
View informations about fixture model.
View ID for the RDM control.
View informations about software version.
PROLIGHTS - Astra Wash19Pix
11 - SHORTCUT
KEYS
UP + DOWN after power on
DOWN then power on
ENTER + UP then power on
MODE
Flip Display
Reset without pan/tilt movements
Bootloader
DESCRIPTION
Directly flip display without enter inside menu.
Fixture will be powered on without reset on pan/tilt movements.
Force firmware upgrade.
PROLIGHTS - Astra Wash19Pix 19
12 - RDM FUNCTIONS
The product can communicate using RDM (Remote Device Management) protocol over a DMX512
Networks.
RDM is a bi-directional communications protocol for use in DMX512 control systems, it is the open standard for DMX512 device configuration and status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without affecting existing non-RDM equipment. It allows a console or dedicated RDM controller to send commands to and receive messages from specific fixtures.
The PIDs in the following tables are supported in the product.
RDM is also available on Wireless and Tiny's Downstead must be enabled in its custom PIDs to work.
SET
20
Category
Product
Information
DMX512
Setup
Dimmer
Settings
Sensors
Parameter
DEVICE_INFO
PRODUCT_DETAIL_ID_LIST
DEVICE_MODEL_DESCRIPTION
MANUFACTURER_LABEL
DEVICE_LABEL
FACTORY_DEFAULTS
SOFTWARE_VERSION_LABEL
BOOT_SOFTWARE_VERSION_ID
BOOT_SOFTWARE_VERSION_LABEL
DMX_PERSONALITY
DMX_PERSONALITY_DESCRIPTION
DMX_START_ADDRESS
SLOT_INFO
SLOT_DESCRIPTION
DEFAULT_SLOT_VALUE
DMX_BLOCK_ADDRESS
DMX_FAIL_MODE
DMX_STARTUP_MODE
DIMMER_INFO
MINIMUM_LEVEL
MAXIMUM_LEVEL
CURVE
CURVE_DESCRIPTION
OUTPUT_RESPONSE_TIME
OUTPUT_RESPONSE_TIME_ DESCRIPTION
MODULATION_FREQUENCY
MODULATION_FREQUENCY_ DESCRIPTION
SENSOR_DEFINITION
SENSOR_VALUE
RECORD_SENSORS
BURN_IN
PROLIGHTS - Astra Wash19Pix
0x00E1
0x00F0
0x0120
0x0121
0x0122
0x0140
0x0141
0x0142
0x0340
0x0341
0x0342
0x0343
0x0344
0x0345
0x0346
PID
0x0060
0x0070
0x0080
0x0081
0x0082
0x0090
0x00C0
0x00C1
0x00C2
0x00E0
0x0347
0x0348
0x0200
0x0201
0x0202
0x0440 x x x x x x x x x x x x x x x x x x x x x x x x x x x
GET x x x x x x x x x x x x x x x x x x x
Power/Lamp
Settings
DEVICE_HOURS
LAMP_HOURS
LAMP_STRIKES
LAMP_STATE
LAMP_ON_MODE
DEVICE_POWER_CYCLES
Display
Settings
DISPLAY_INVERT
DISPLAY_LEVEL
Configuration PAN_INVERT
TILT_INVERT
PAN_TILT_SWAP
REAL_TIME_CLOCK
Control
LOCK_PIN
LOCK_STATE
LOCK_STATE_DESCRIPTION
IDENTIFY_DEVICE
RESET_DEVICE
POWER_STATE
PERFORM_SELFTEST
SELF_TEST_DESCRIPTION
CAPTURE_PRESET
PRESET_PLAYBACK
IDENTIFY_MODE
PRESET_INFO
PRESET_STATUS
PRESET_MERGEMODE
IP & DNS
Configuration
POWER_ON_SELF_TEST
IPV4_CURRENT_ADDRESS
IPV4_STATIC_ADDRESS
Custom Pids FIX. ENGINE PROT. (0:W/DMX 1:sACN
2:ArtNet)
PIX. ENGINE PROT. (0:W/DMX 1:sACN
2:ArtNet 3:sAK 4:ArtK)
PIX. ENGINE ADDR. (1-512)
PIX. ENGINE MODE (0:Off 1:Ring 2:Pixel)
KLINGNET (0:Off 1:On)
0x1030
0x1031
0x1040
0x1041
0x1042
0x1043
0x1044
0x0705
0x0640
0x0641
0x0642
0x1000
0x1001
0x1010
0x1020
0x1021
0x0706
0x0400
0x0401
0x0402
0x0403
0x0404
0x0405
0x0500
0x0501
0x0600
0x0601
0x0602
0x0603
0x8010
0x8020
0x8030
0x8040
0x8050 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
PROLIGHTS - Astra Wash19Pix 21
13 - DMX CHARTS
22
10
11
8
9
12
13
Channel
1
2
3
6
7
4
5
14
15
16
21
22
27
28
29
30
23
24
25
26
31
32
33
34
35
17
18
19
20
Basic
Pan
Pan Fine
Tilt
Tilt Fine
Dimmer
Dimmer Fine
Shutter / Strobe
Red
Green
Blue
White
Color Macro
CTC
Zoom
Crossfade from Artnet to
Klingnet
Pan
Pan Fine
Fixture Engine
FX
Pan
Pan Fine
Standard
Tilt
Tilt Fine
Dimmer
Dimmer Fine
Shutter / Strobe
Red
Green
Blue
Tilt
Tilt Fine
Dimmer
Dimmer Fine
Shutter / Strobe
Red
Red Fine
Green
White
CTC
Green Fine
Blue
Zoom
Crossfade from Artnet to
Klingnet
Blue Fine
White
Crossfade for Pixel Engine White Fine
Pan
Pan Fine
Extended
Tilt
Tilt Fine
Dimmer
Dimmer Fine
Shutter / Strobe
Red
Red Fine
Green
Green Fine
Blue
Blue Fine
White
White Fine
Color Macro Color Macro
Crossfade from White to
Color
Control
Control
Pattern
Ring Foreground Intensity Pattern Speed
Ring Foreground Strobe Pattern Fade
Ring Foreground Red
Ring Foreground Green
Ring Foreground Blue
Pattern Transition
Foreground Intensity
Foreground Strobe
Background Intensity
Background Strobe
Background Red
Background Green
Background Blue
Background White
Ring Dimmer
Ring Pattern
Ring Pattern Speed
Ring Pattern Fade
Ring Pattern Transition
Ring Foreground Intensity
CTC CTC
Zoom Zoom
Zoom Fine
Crossfade from Artnet to
Klingnet
Zoom Fine
Crossfade from Artnet to
Klingnet
Crossfade for Pixel Engine Crossfade for Pixel Engine
Crossfade from White to
Color
Control
Crossfade from White to
Color
Control
CTO on colors
Tint
CTO on colors
Tint
Ring Foreground Intensity Pattern
Ring Foreground Strobe Pattern Speed
Ring Foreground Red
Ring Foreground Green
Ring Foreground Blue
Pattern Fade
Pattern Transition
Foreground Intensity
Foreground Strobe
Background Intensity
Background Strobe
Background Red
Background Green
PROLIGHTS - Astra Wash19Pix
49
50
51
52
45
46
47
48
Channel
36
37
38
39
40
41
42
43
44
12
...
73
74
75
76
10
11
8
9
6
7
4
5
Channel
1
2
3
...
Basic FX
Ring Foreground Strobe
Ring Foreground Red
Ring Foreground Green
Ring Foreground Blue
Ring Background Intensity
Ring Background Strobe
Ring Background Red
Ring Background Green
Ring Background Blue
Standard
Off
Pixel Engine
Ring
Red 1
Green 1
Blue 1
White 1
Red 2
Green 2
Blue 2
White 2
Red 3
Green 3
Blue 3
White 3
...
PROLIGHTS - Astra Wash19Pix
Red 1
Green 1
Blue 1
White 1
Red 2
Green 2
Blue 2
White 2
Red 3
Green 3
Blue 3
White 3
...
Red 19
Green 19
Blue 19
White 19
Pixel
Extended
Background Blue
Background White
Ring Dimmer
Ring Pattern
Ring Pattern Speed
Ring Pattern Fade
Ring Pattern Transition
Ring Foreground Intensity
Ring Foreground Strobe
Ring Foreground Red
Ring Foreground Green
Ring Foreground Blue
Ring Background Intensity
Ring Background Strobe
Ring Background Red
Ring Background Green
Ring Background Blue
23
24
Bas FX Std Ext
1 1 1 1
2
3
4
5
6
7
8
9
10
11
12
2
3
4
5
6
7
8
9
10
11
2
3
4
5
6
7
8
10
11
12
13
14
15
16
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PAN
Lineary from 0% to 100%
PAN FINE
Lineary from 0% to 100%
TILT
Lineary from 0% to 100%
TILT FINE
Lineary from 0% to 100%
DIMMER
Lineary from close to open
DIMMER FINE
Lineary from close to open
SHUTTER
Close
Strobe from slow to fast
Open
Pulse in from slow to fast
Open
Pulse out from slow to fast
Open
Random from slow to fast
Open
RED
Lineary from 0% to 100%
RED FINE
Lineary from 0% to 100%
GREEN
Lineary from 0% to 100%
GREEN FINE
Lineary from 0% to 100%
BLUE
Lineary from 0% to 100%
BLUE FINE
Lineary from 0% to 100%
WHITE
Lineary from 0% to 100%
WHITE FINE
Lineary from 0% to 100%
COLOR MACRO
Open
Red
Green
Blue
Cyan
Magenta
Yellow
Dirty White
Alice Bllue
Congo Blue
Dark Steel Blue
Deep Lavender
Lilac Ting
Daylight Blue
Flame Red
Bastard Amber
Deep Orange
Pale Gold
Apricot
Bright Blue
Primary Green
Special Lavender
Pale Lavender
Deep Golden Amber
Medium Blue
Bright Pink
Mauve
Dark Green
Lee Green
Dark Blue
Function
PROLIGHTS - Astra Wash19Pix
DMX Value
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 001
002 ÷ 062
063 ÷ 064
065 ÷ 125
126 ÷ 127
128 ÷ 188
189 ÷ 190
191 ÷ 251
252 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
032 ÷ 033
034 ÷ 035
036 ÷ 037
038 ÷ 039
040 ÷ 041
042 ÷ 043
044 ÷ 045
046 ÷ 047
048 ÷ 049
050 ÷ 051
052 ÷ 053
054 ÷ 055
056 ÷ 057
058 ÷ 059
000 ÷ 001
002 ÷ 003
004 ÷ 005
006 ÷ 007
008 ÷ 009
010 ÷ 011
012 ÷ 013
014 ÷ 015
016 ÷ 017
018 ÷ 019
020 ÷ 021
022 ÷ 023
024 ÷ 025
026 ÷ 027
028 ÷ 029
030 ÷ 031
Default
128
128
128
128
000
000
255
000
255
255
255
255
255
255
255
255
Bas FX Std Ext
12
13
14
12
13
16
17
18
19
16
17
18
19
4400K
4600K
4800K
5000K
5200K
5400K
5600K
6000K
6500K
7000K
8000K
9000K
10000K
Full On
Lee Minus Green
Pale Gold
Orange
Deep Straw
Rose Purple
Deep Purple
Soft Green
Reserved
2800K
3000K
3200K
3400K
3600K
3800K
4000K
4200K
COLOR MACRO
Light Blue
Steel Blue
Medium Blue÷Green
Peacock Blue
Magenta
Dark Pink
Middle Rose
Light Salmon
English Rose
Light Rose
Orange
Deep Amber
Straw
Light Amber
Spring Yellow
Dark Yellow Green
Just Blue
Sky Blue
Lavender
Light Lavender
Pink Carnation
Medium Pink
Light Pink
Sunset Red
Dark Amber
Gold Amber
Medium Amber
Fire
Surprise Peach
Straw Tint
Medium Yellow
CTC
Linear from 2800K to 10000K
ZOOM
Lineary from 0% to 100%
ZOOM FINE
Lineary from 0% to 100%
Function
PROLIGHTS - Astra Wash19Pix
DMX Value
230 ÷ 231
232 ÷ 233
234 ÷ 235
236 ÷ 237
238 ÷ 239
240 ÷ 241
242 ÷ 243
244 ÷ 245
246 ÷ 247
248 ÷ 249
250 ÷ 251
252 ÷ 253
254 ÷ 255
124 ÷ 125
126 ÷ 127
128 ÷ 129
130 ÷ 131
132 ÷ 133
134 ÷ 135
136 ÷ 211
212 ÷ 213
214 ÷ 215
216 ÷ 217
218 ÷ 219
220 ÷ 221
222 ÷ 223
224 ÷ 225
226 ÷ 227
228 ÷ 229
092 ÷ 093
094 ÷ 095
096 ÷ 097
098 ÷ 099
100 ÷ 101
102 ÷ 103
104 ÷ 105
106 ÷ 107
108 ÷ 109
110 ÷ 111
112 ÷ 113
114 ÷ 115
116 ÷ 117
118 ÷ 119
120 ÷ 121
122 ÷ 123
060 ÷ 061
062 ÷ 063
064 ÷ 065
066 ÷ 067
068 ÷ 069
070 ÷ 071
072 ÷ 073
074 ÷ 075
076 ÷ 077
078 ÷ 079
080 ÷ 081
082 ÷ 083
084 ÷ 085
086 ÷ 087
088 ÷ 089
090 ÷ 091
000 ÷ 255
000 ÷ 255
000 ÷ 255
Default
000
000
000
000
25
26
Bas FX Std Ext
15 14 20 20
16
17
18
15
16
17
21
22
23
21
22
23
Function
CROSSFADE FROM ArtNet/sACN TO Klingnet
Linear from Pixel Engine to Klingnet
CROSSFADE FROM Color Engine TO Pixel Engine
Linear from Color Engine to Pixel Engine
CROSSFADE FROM WHITE TO COLOR
Linear from CTC to Color engine
CONTROL
No Function
KLINGNET ON
KLINGNET OFF
PAN REVERSE ON
PAN REVERSE OFF
TILT REVERSE ON
TILT REVERSE OFF
PAN/TILT MODE FAST
PAN/TILT MODE MEDIUM
PAN/TILT MODE SLOW
PAN/TILT MODE SYNC
MOVEMENT IN BLACKOUT ON
MOVEMENT IN BLACKOUT OFF
HOME POSITION STANDARD
HOME POSITION CUSTOM
DISPLAY ON
DISPLAY 10S
DISPLAY 20S
DISPLAY 30S
FLIP DISPLAY ON
FLIP DISPLAY OFF
FLIP DISPLAY AUTO
KEY LOCK ON
KEY LOCK OFF
FAN MODE AUTO
FAN MODE SILENT
FAN MODE HIGH
WHITE CALIBRATION OFF
WHITE CALIBRATION STUDIO
WHITE CALIBRATION 8000K
NO SIGNAL HOLD
NO SIGNAL BLACKOUT
STATUS LED ON
STATUS LED OFF
DIMMER CURVE LINEAR
DIMMER CURVE S÷CURVE
DIMMER CURVE SQUARE LAW
DIMMER CURVE INVERSE SQUARE LAW
DIMMER SPEED AUTO
DIMMER SPEED FAST
DIMMER SPEED MEDIUM
DIMMER SPEED SLOW
LED FREQUENCY 600HZ
LED FREQUENCY 1200HZ
LED FREQUENCY 2000HZ
LED FREQUENCY 4000HZ
LED FREQUENCY 6000HZ
LED FREQUENCY 25KHZ
LED FREQUENCY 50KHZ
INVERT MAPPING ON
INVERT MAPPING OFF
ZOOM MODE STANDARD
ZOOM MODE PIXELS
INVERT ZOOM OFF
INVERT ZOOM ON
TUNGSTEN EMULATION ON
TUNGSTEN EMULATION OFF
RESET ALL
RESET PAN
RESET TILT
RESET PAN/TILT
RESET ZOOM
Reserved
FACTORY DEFAULT OF CONTROL FUNCTIONS
PROLIGHTS - Astra Wash19Pix
DMX Value
000 ÷ 255
000 ÷ 255
000 ÷ 255
096 ÷ 097
098 ÷ 099
100 ÷ 101
102 ÷ 103
104 ÷ 105
106 ÷ 107
108 ÷ 109
110 ÷ 111
112 ÷ 113
114 ÷ 115
116 ÷ 117
118 ÷ 119
120 ÷ 121
122 ÷ 123
124 ÷ 253
254 ÷ 255
064 ÷ 065
066 ÷ 067
068 ÷ 069
070 ÷ 071
072 ÷ 073
074 ÷ 075
076 ÷ 077
078 ÷ 079
080 ÷ 081
082 ÷ 083
084 ÷ 085
086 ÷ 087
088 ÷ 089
090 ÷ 091
092 ÷ 093
094 ÷ 095
032 ÷ 033
034 ÷ 035
036 ÷ 037
038 ÷ 039
040 ÷ 041
042 ÷ 043
044 ÷ 045
046 ÷ 047
048 ÷ 049
050 ÷ 051
052 ÷ 053
054 ÷ 055
056 ÷ 057
058 ÷ 059
060 ÷ 061
062 ÷ 063
000 ÷ 001
002 ÷ 003
004 ÷ 005
006 ÷ 007
008 ÷ 009
010 ÷ 011
012 ÷ 013
014 ÷ 015
016 ÷ 017
018 ÷ 019
020 ÷ 021
022 ÷ 023
024 ÷ 025
026 ÷ 027
028 ÷ 029
030 ÷ 031
Default
000
000
000
000
Bas FX Std Ext
24 24
18
19
20
21
22
23
25 25
26
27
28
29
30
31
Function
CTO ON COLORS
Lineary from 0% to 100%
TINT
+25 % to +0 % magenta balanced
+0 % to +25 % green
PATTERN
No FX
All rings In & Out
All rings In & Out Bouncing
Single Ring In & Out
Single Ring In & Out Bouncing
All Pixels In & Out in Right Direction
Single Line In & Out in Right Direction
Single Line In & Out Bouncing in Left / Right Direction
All Pixels In & Out in Bottom Direction
Single Line In & Out in Bottom Direction
Single Line In & Out Bouncing in Top / Bottom Direction
Half Pixels rotating clockwise
Fixture divided into 2 parts ring effect
Random with 1px Density
Random with 2px Density
Random with 4px Density
Random with 5px Density
Random with 7px Density
Pixel Going around Ring 1
Pixel Going around Ring 1
Pixel Going around Ring 2
Pixel Going around Ring 2
Pixel Going around Ring 2
Pixel Going around Ring 2
Clock rotating anti÷clockwise
Two squares rotating while moving from center
Wiggling Line
Two rotating 2x2px squares
Pixels In & Out on Ring 2 side to side
Triangle from 9 pixels rotate to right
Wiggling clock
2 hands moving up and down
Aperture effect
Aperture Effect with 1 px only
2 Pixels Going around Ring 2
3 Pixels Going around Ring 2
Bottom Half Open / Close than Top Half Open Close
Moving Fists
Pixels coming in zigzak shape
2 Arc's rotating
2 2px wide lines rotating
PATTERN SPEED
Indexing
CW from fast to slow
Stop
CCW from slow to fast
PATTERN FADE
Lineary from 0% to 100%
PATTERN TRANSITION
Lineary from 0% to 100%
FOREGROUND INTENSITY
Lineary from 0% to 100%
FOREGROUND STROBE
Close
Strobe from slow to fast
Open
Pulse in from slow to fast
Open
Pulse out from slow to fast
Open
Random from slow to fast
Open
PROLIGHTS - Astra Wash19Pix
DMX Value
000 ÷ 127
128 ÷ 190
191 ÷ 192
193 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 001
002 ÷ 062
063 ÷ 064
065 ÷ 125
126 ÷ 127
128 ÷ 188
189 ÷ 190
191 ÷ 251
252 ÷ 255
000 ÷ 255
000 ÷ 127
128
129 ÷ 255
107 ÷ 112
113 ÷ 118
119 ÷ 124
125 ÷ 130
131 ÷ 136
137 ÷ 142
143 ÷ 148
149 ÷ 154
155 ÷ 160
161 ÷ 166
167 ÷ 172
173 ÷ 178
179 ÷ 184
185 ÷ 190
191 ÷ 196
197 ÷ 202
000 ÷ 016
017 ÷ 022
023 ÷ 028
029 ÷ 034
035 ÷ 040
041 ÷ 046
047 ÷ 052
053 ÷ 058
059 ÷ 064
065 ÷ 070
071 ÷ 076
077 ÷ 082
083 ÷ 088
089 ÷ 094
095 ÷ 100
101 ÷ 106
203 ÷ 208
209 ÷ 214
215 ÷ 220
221 ÷ 226
227 ÷ 232
233 ÷ 238
239 ÷ 244
245 ÷ 250
251÷ 255
Default
000
128
000
000
000
000
000
255
27
28
Bas FX Std Ext
24
25
26
27
28
29
30
31
32
33
32
33
34
35
36
37
38
39
40
41
Function
BACKGROUND INTENSITY
Lineary from 0% to 100%
BACKGROUND STROBE
Close
Strobe from slow to fast
Open
Pulse in from slow to fast
Open
Pulse out from slow to fast
Open
Random from slow to fast
Open
BACKGROUND RED
Lineary from 0% to 100%
BACKGROUND GREEN
Lineary from 0% to 100%
BACKGROUND BLUE
Lineary from 0% to 100%
BACKGROUND WHITE
Lineary from 0% to 100%
RING DIMMER
Lineary from 0% to 100%
RING PATTERN
No FX
Single Line going around Ring 1
Single Line going around Ring 2
Single Line going around Ring 3
Single Line going around Ring 4
Single Line going around Ring 5
Two Lines going around Ring 1
Two Lines going around Ring 2
Two Lines going around Ring 3
Two Lines going around Ring in opposed direction 1
Two Lines going around Ring in opposed direction 2
Two Lines going around Ring in opposed direction 3
Three Lines going around Ring 1
Three Lines going around Ring 2
Six Lines going around Ring
Random Pixels 20 steps 1
Random Pixels 20 steps 2
Random Pixels 20 steps 3
Random Pixels 20 steps 4
Random Pixels 20 steps 5
Ring Opening and closing in horizontal axis
Ring Opening and closing in vertical axis
Ring Opening and closing in horizontal and vertical axis
Ring Opening in horizontal axis and closing in vertical axis
Ring divided into 4 parts chase
Ring divided into 8 parts chase
2 Lines going from Left to Right Loop
2 Lines going from Top to Bottom Loop
Ring divided into 4 parts doing chase
Ring divided into 4 parts doing chase
Ring divided into 4 parts doing chase
Reserved
Top|Bottom|Left|Right
2 Lines Swing
Random Open of pixels
Pixel 1 thru 102 On than 102 thru 1 Off
Pixel 1 thru 102 On than 1 thru 102 Off
Moving anchor
Anchor rotated 180 degree
RING PATTERN SPEED
Indexing
CW from fast to slow
Stop
CCW from slow to fast
RING PATTERN FADE
Lineary from 0% to 100%
PROLIGHTS - Astra Wash19Pix
DMX Value
000 ÷ 255
000 ÷ 001
002 ÷ 062
063 ÷ 064
065 ÷ 125
126 ÷ 127
128 ÷ 188
189 ÷ 190
191 ÷ 251
252 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
107 ÷ 112
113 ÷ 118
119 ÷ 124
125 ÷ 130
131 ÷ 136
137 ÷ 142
143 ÷ 148
149 ÷ 154
155 ÷ 160
161 ÷ 166
167 ÷ 172
173 ÷ 178
179 ÷ 184
185 ÷ 190
191 ÷ 196
197 ÷ 214
000 ÷ 016
017 ÷ 022
023 ÷ 028
029 ÷ 034
035 ÷ 040
041 ÷ 046
047 ÷ 052
053 ÷ 058
059 ÷ 064
065 ÷ 070
071 ÷ 076
077 ÷ 082
083 ÷ 088
089 ÷ 094
095 ÷ 100
101 ÷ 106
215 ÷ 220
221 ÷ 226
227 ÷ 232
233 ÷ 238
239 ÷ 244
245 ÷ 250
251÷ 255
000 ÷ 127
128 ÷ 190
191 ÷ 192
193 ÷ 255
000 ÷ 255
Default
000
255
000
000
000
000
000
000
000
000
Bas FX Std Ext
19
20
21
22
23
34
35
36
37
38
39
40
41
42
43
44
26
27
28
29
30
42
43
44
45
46
47
48
49
50
51
52
RING PATTERN TRANSITION
Lineary from 0% to 100%
RING FOREGROUND INTENSITY
Lineary from 0% to 100%
RING FOREGROUND STROBE
Close
Strobe from slow to fast
Open
Pulse in from slow to fast
Open
Pulse out from slow to fast
Open
Random from slow to fast
Open
RING FOREGROUND RED
Lineary from 0% to 100%
RING FOREGROUND GREEN
Lineary from 0% to 100%
RING FOREGROUND BLUE
Lineary from 0% to 100%
RING BACKGROUND INTENSITY
Lineary from 0% to 100%
RING BACKGROUND STROBE
Close
Strobe from slow to fast
Open
Pulse in from slow to fast
Open
Pulse out from slow to fast
Open
Random from slow to fast
Open
RING BACKGROUND RED
Lineary from 0% to 100%
RING BACKGROUND GREEN
Lineary from 0% to 100%
RING BACKGROUND BLUE
Lineary from 0% to 100%
Function DMX Value
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 001
002 ÷ 062
063 ÷ 064
065 ÷ 125
126 ÷ 127
128 ÷ 188
189 ÷ 190
191 ÷ 251
252 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 001
002 ÷ 062
063 ÷ 064
065 ÷ 125
126 ÷ 127
128 ÷ 188
189 ÷ 190
191 ÷ 251
252 ÷ 255
000 ÷ 255
000 ÷ 255
000 ÷ 255
Default
000
000
255
255
000
000
000
000
000
000
000
PROLIGHTS - Astra Wash19Pix 29
14 - RING LAYOUT
3
2
1
Fig. 09
30
15 - PIXEL LAYOUT
9
10
11
3
2
8
7
19
18
1
12
4
6
17
5
13
16
14
15
PROLIGHTS - Astra Wash19Pix
Fig. 10
16 - ERROR MESSAGES
The error is shown on the unit display. In the table below, the "ERROR SHOWED ON SCREEN" column lists the possible errors, accompanied by a possible cause ("POSSIBLE" CAUSES "column).
The color of the error messages (listed in the "COLOR MESSAGES" column) is different for each board it refers to ("PCB" column).
On page 32 you can see the location of the various pcb boards.
ERROR SHOWED ON
SCREEN
[DISPLAY BATTERY
ERROR]
[BASE FAN 1 ERROR]
POSSIBLE CAUSES
Blower for cooling the ignitor failed.
COLOUR
MESSAGES
Battery not present or not detected from the display PCB.
Green
Green
1U
1U
PCB
[BASE FAN 2 ERROR]
[DMX ACTIVE]
1U
1U
[MAINTENANCE TIME]
[PAN/TILT PCB ERROR]
[PAN MOTOR ERROR]
[TILT MOTOR ERROR]
[PAN LOCKED]
[TILT LOCKED]
Blower for cooling the power supply failed.
Green
If transfer configuration is used with dmx signal connected.
Need to be done standard maintenance and also reset of elapsed time.
Green
Green
Pan tilt pcb not detected.
Blue
This message will appear after the reset of the product if:
• the PAN magnetic-indexing circuit detect a failure (sensor failed or magnet is missing);
• or the stepping motor is defective;
• or its driving IC on the PCB is defective;
• or the product is not located in the default position after the reset of the fixture.
Blue
This message will appear after the reset of the product if:
• the TILT magnetic-indexing circuit detect a failure (sensor failed or magnet is missing);
• or the stepping motor is defective;
• or its driving IC on the PCB is defective;
• or the product is not located in the default position after the reset of the fixture.
Blue
Pan is locked.
Blue
Tilt is locked.
Blue
1U
2U
2U
2U
2U
2U
[PAN SENSOR ERROR] 2U
[LED FAN 1 ERROR]
[LED FAN 2 ERROR]
Pan sensor not detected.
Blue
One of the blowers for cooling the source failed, the source has been switched OFF.
Blue
One of the blowers for cooling the source failed, the source has been switched OFF.
Blue
PROLIGHTS - Astra Wash19Pix
2U
2U
31
32
[TILT SENSOR ERROR] Tilt sensor not detected.
[PAN ENCODER ERROR] Pan encoder not detected.
Blu
Blu
[TILT ENCODER ERROR] Tilt encoder not detected.
Blu
[DRIVER/LED PCB ERROR] Led driver pcb not detecteld Yellow
[ZOOM ERROR]
[LED DRIVER
TEMPERATURE ERROR]
[RING DRIVER PCB
ERROR]
Failure detected during the reset of the
ZOOM system, if the zoom lens is not located in its default position.
Yellow
This error message indicates that an overheating in the head has occurred
Yellow and the lamp has been switched OFF by the product protection system.
RING DRIVER PCB not detected during reset
Yellow
[LED PCB ERROR] LED PCB 1 not detected during reset Yellow
IDENTIFICATION OF ELECTRONIC BOARDS
3U PCB
3U
3U
3U
2U
2U
2U
3U
3U
2U PCB
1U PCB
PROLIGHTS - Astra Wash19Pix
Fig. 11
17 - ACCESSORIES INSTALLATION
EGG CRATE (ASTRAW19PEC - OPTIONAL)
3
2
1
Before removing rear cover, place the head in a horizontal position and engage both the PAN and
TILT locks for added stability. See the "PAN AND TILT LOCK" paragrap.
Loosen and remove the marked six screws (1). Then insert the egg crate (2) and fix the six screws (3).
Fig. 12
PROLIGHTS - Astra Wash19Pix 33
18 - PERIODICAL CLEANING
WARNING! Turn OFF power and allow approximately 20 minutes for the fixture to cool down.
34
Use a soft cloth dampened with any detergent liquid for cleaning to remove the dirt from the optics.
Fig. 13
PROLIGHTS - Astra Wash19Pix
19 - MAINTENANCE
MAINTENANCE AND CLEANING THE PRODUCT
WARNING: Disconnect from the mains before starting any maintenance work
It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or other particles to ensure that the light is radiated at maximum brightness.
• For cleaning, disconnect the main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might penetrate the unit and cause damage to it.
• The user must clean the product periodically to maintain optimum performance and cooling. The user may also upload firmware (product software) to the fixture via the DMX signal input port or USB port using firmware and instructions from PROLIGHTS.
• The frequency of such maintenance operations is to be performed according to various factors, such as the amount of the use and the condition of the installation environment (air humidity, presence of dust, salinity, etc.). It is recommended that the product is subject to annual service by a qualified technician for special maintenance involving at least the following procedures:
• General cleaning of internal parts.
• For all the parts subject to friction, using lubricants specifically supplied by PROLIGHTS.
• General visual check of the internal components, cabling, mechanical parts, etc.
• Electrical, photometric and functional checks; eventual repairs.
• Cleaning the lenses. Only use neutral soap and water to clean the lenses, then dry it carefully with a soft, non-abrasive cloth.
WARNING: the use of alcohol or any other detergent could damage the lenses.
• All other service operations on the product must be carried out by PROLIGHTS, its approved service agents or trained and qualified personnel.
• It is PROLIGHTS policy to apply the strictest possible calibration procedures and use the best quality materials available to ensure optimum performance and the longest possible component lifetimes.
However, optical components are subject to wear and tear over the life of the product, resulting in gradual changes in colours over many thousands of hours of use. The extent of wear and tear depends heavily on operating conditions and environment, so it is impossible to specify precisely whether and to what extent performance will be affected. However, you may eventually need to re place optical components if their characteristics are affected by wear and tear after an extended pe riod of use and if you require fixtures to perform within very precise optical and colour parameters.
• Do not apply filters, lenses or other materials on lenses or other optical components. Use only accessories approved by PROLIGHTS.
REPLACING THE FUSE
WARNING: Before replacing the fuse, unplug the product from the mains.
• Remove the old fuse from the housing with a suitable screwdriver (anticlockwise) and replace it with one of the same type and of the same classification (T8A 250V).
VISUAL CHECK OF PRODUCT HOUSING
• The parts of the product cover/housing should be checked for eventual damages and breaking start at least every two months. In addition, especially the parts of the front lens holder have to be checked mechanically (by means of movement by the part) if it is firmly fastened to the fixture. If hint of a crack is found on some plastic part, do not use the product until the damaged part will be replaced.
• Cracks or another damages of the cover/housing parts can be caused by the product transportation or manipulation and also ageing process may influence materials.
• This checking is necessary for both fixed installations and preparing product for renting. Any free moving parts inside of the product, cracked cover/housing or any part of front lens not sitting prop erly in place need to be immediately replaced.
PROLIGHTS - Astra Wash19Pix 35
36
TROUBLESHOOTING
Problems Possible causes Checks and remedies
Product doesn’t power ON • No power to the product
• Check that power is switched ON and cables are plugged in.
• Fuse blown or internal fault
• Check if the Fuse is intact and eventually replace it if necessary.
• Contact the PROLIGHTS Service or authorized service partner. Do not remove parts and/or covers, or carry out any repairs or service that are not described in this Safety and User Manual unless you have both authorization from PROLIGHTS and the service documentation.
Product reset correctly but does not respond correctly to the contoller.
Timeout error after fixture reset.
• Bad signal connection • Inspect connections and cables. Fix eventual bad connections. Repair or replace damaged cables.
• Signal connection not terminated
• Insert DMX termination plug in signal output socket of the last product on the signal line.
• Incorrect addressing of the product
• Check the product address and control settings
• One of the product is defective and is corrupt ing the signal transmis sion on the signal line
• Unplug the XLR in and out connectors and connect them directly together to bypass one product at a time until normal operation is regained. Once found the error, have that fixture serviced by a qualified technician.
• One or more hardware components requires mechanical adjustments
• Check product stored error messages for more information. Contact PROLIGHTS Service or an authorized service partner.
Mechanical effect loses position
Light output turn OFF
Intermittently
• Mechanical hardware require cleaning, adjust ment or lubrification
• Fixture is too hot
• Check product stored error messages for more information. Contact PROLIGHTS Service or an authorized service partner.
• Check product stored error messages.
• Allow product to cool.
• Clean the product and airflow filters.
• Reduce ambient temperature.
• Hardware failure (tem perature sensor, fans,
Light source...)
• Check product stored error messages for more information. Contact. PROLIGHTS Service or an authorized service partner.
General low light intensity • Dirty lens assembly
• Dirty or damaged filters
• Clean the fixture regularly.
• Install lens assembly properly.
Contact an authorized service center in case of technical problems or not reported in the table can not be resolved by the procedure given in the table.
PROLIGHTS - Astra Wash19Pix
Note
Note
Note
Note
PROLIGHTS is a trademark of
MUSIC & LIGHTS S.r.l.
musiclights.it
Via A.Olivetti snc
04026 - Minturno (LT) ITALY
Tel: +39 0771 72190 prolights.it
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project