Allen-Bradley 140G-H Installation Manual
Allen-Bradley 140G-H is a communication module for 140G-H and 140G-J circuit breakers. It allows for remote monitoring and control of the circuit breaker, including the ability to trip, close, and monitor the status of the circuit breaker. The module communicates with a host system via a shielded twisted pair cable.
The 140G-H communication module is ideal for use in applications where remote monitoring and control of circuit breakers is desired. This can include applications such as:
- Power distribution systems
- Industrial automation systems
- Data centers
- Critical infrastructure
Advertisement
Advertisement
Bul. 140G/140MG
DIR 1000721R0609 Version 01 - 140G-H-CIM
Communication module for 140G-H, 140G-J
Modulo di comunicazione
Installation - Installazione - Instalación
Instalação - -
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E).
警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。(
NFPA70E
の要件に従ってください)
警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备
物
140G-H
1
CLACK
140G-J
140G-H
140G-J
x1 x1 x1 x1 x1 x1 x1 x1
DIR 1000721R0609 Version 01
Com module
Cable retainer Cables
1
3
1
2
2
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
3
5
5
2 3
6
2
1
1
DIR 1000721R0609 Version 01
(2)
CLICK
4
140G-H, 140G-J
4
140G-J
140G-H
6
5
140G-H
7
140G-H
140G-H
8
140G-H
9
140G-J
DIR 1000721R0609 Version 01
(3)
10
140G-J
11
140G-J
12
140G-J
13
DIR 1000721R0609 Version 01
(4)
Remove the plugs
14 15
16
2
1
2
3
Optional (*)
(*) Supplied with the MCCB
17
DIR 1000721R0609 Version 01
(5)
18
1
2
3
3
CLICK
4
DIR 1000721R0609 Version 01
6
6
5
5
9.7 lb-in
1.1 Nm
(6)
140G-H, 140G-J
19
TO XH1 CONNECTION
ON ELECTRONIC
TRIP UNIT
COMMUNICATION
MODULE
H & J FRAME
140G - H - CIM
Shielded twisted pair wires
CUSTOMER
CONNECTION
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/ sustainability-ethics/product-environmental-compliance.page
Publication 140G-IN104B-MU-P - February 2016 DIR 1000721R0609 Version 01 (L9011) - B0613
Copyright © 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.

Public link updated
The public link to your chat has been updated.
Advertisement