CipherLab 8500 Series, 8570, 8580, 8590 Reference Manual
Advertisement
Advertisement
Printed on 18 May, 2007
Reference Manual for 8500, 8570, 8580, 8590
8500 Series Mobile
Computer
Version 2.00
Copyright Notice
Copyright © 2007 CIPHERLAB CO., LTD.
All rights reserved
The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited.
Due to continued product development this information may change without notice. The information and intellectual property contained herein is confidential between CIPHERLAB and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find any problems in the documentation, please report them to us in writing. CIPHERLAB does not warrant that this document is error-free.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of CIPHERLAB CO., LTD.
For product consultancy and technical support, please contact your local sales representative. Also, you may visit our web site for more information.
The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD.
CIPHERLAB CO., LTD.
Website: http://www.cipherlab.com
II
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Important Safety Precautions
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
The use of any batteries or charging devices, which are not originally sold or manufactured by
CipherLab, will void your warranty and may cause damage to human body or the product itself.
The charging and communication cradle uses an AC power adaptor. A socket outlet shall be installed near the equipment and shall be easily accessible. The power adaptor should comply with L.P.S test.
Make sure there is stable power supply for the mobile computer or its peripherals to operate properly.
DO NOT disassemble, incinerate or short circuit the battery pack.
DO NOT expose the mobile computer or the battery pack to any flammable sources.
Under no circumstances, internal components are self-serviceable.
Per FDA and IEC standards, the scan engines described in this manual are not given a laser classification. However, the following precautions should be observed:
CAUTION
This laser component emits FDA/IEC Class 2 laser light at the exit port. Do not stare into beam.
III
Care & Maintenance
The 8500 Series is intended for industrial logistics use. The mobile computer is rated IP 64, however, it may do damage to the mobile computer when being exposed to extreme temperatures or soaked wet.
When the body of the mobile computer gets dirty, use a clean and wet cloth to wipe off the dust. DO
NOT use/mix any bleach or cleaner. Always keep the LCD dry.
For a liquid crystal display (LCD) or touch screen, use a clean, non-abrasive, lint-free cloth to wipe dust off the screen. DO NOT use any pointed or sharp object to move against the surface.
Battery disposal – For green-environment issue, it is important that batteries should be recycled in a proper way.
If you want to put away the mobile computer for a period of time, download the collected data to a host computer, and then take out the battery pack. Store the mobile computer and battery pack separately.
When the mobile computer resumes its work, the main and backup batteries will take a certain time to become fully charged.
If you shall find the mobile computer malfunctioning, refer to the Troubleshooting section for self help first.
If the problem persists, write down the specific scenario and consult your local sales representative.
Getting Started
Below are instructions of how to have the mobile computer ready to work. This scenario makes use of a cradle, which may be replaced by the 4-slot battery charger and other interface to PC.
Set up the cradle for initial charging.
Install the battery pack to the mobile computer, and then seat the mobile computer in the cradle for charging. You may charge a second battery pack at the same time.
When charging is done, turn on the mobile computer and enter the System Menu for system configuration, downloading programs and font file, and so on.
Before downloading, you must connect a serial cable between the cradle and a host computer.
Refer to the System Menu > 6. Load Program for more information.
After charging and downloading, the mobile computer is ready for use.
Install the hand strap or pistol grip if necessary.
IV
Contents
Copyright Notice
FCC Regulations
Important Safety Precautions
Care & Maintenance
Getting Started
IV
Preface
1
CHAPTER 1 - Introduction
3
II
III
III
IV
i
ii Contents
CHAPTER 2 - Installation
25
CHAPTER 3 - Software Architecture
35
CHAPTER 4 - Configuration
39
Contents iii
Specifications
Troubleshooting
APPENDIX I - Download Utilities
95
89
91
iv Contents
Table of Figures
Preface
1
Answering heavy industrial demands for robust, versatile and high performance computers, the 8500 Series Mobile Computer is specifically designed for all-day, everyday use as well as for data-intensive applications in harsh environments.
This line of product comes with built-in Bluetooth wireless technology and allows for optional modules for 802.11b/g as well as GSM/GPRS, enabling all the time, anywhere applications and seamless real time sharing of performance. The 8500 Series is bundled with powerful and rich features to ensure success in timely processing of information, even in rigorous industrial environments, and thus, makes an ideal choice for a wireless solution in either increasing business flexibility or answering the demanding needs of heavy-duty mobile computers. Being programmable, this handy device can run custom applications or terminal emulation applications.
This manual serves to guide you through how to install, configure, and operate the mobile computer. We recommend you to keep one copy of the manual at hand for quick reference or maintenance purposes. To avoid any improper disposal or operation, please read the manual thoroughly before use.
Thank you for choosing CipherLab products!
2 8500 Series Series Reference Manual
Revision History
Version Release Date
1.07 Oct. 31, 2006
1.06
1.05
1.04
1.03
1.02
1.00
July 27, 2006
June 22, 2006
June 16, 2006
May 23, 2006
Apr. 4, 2006
Mar. 1, 2006
Notes
Modified: section 1.5.9 List by standards for RFID tags
Modified: section 1.5.10 Bluetooth specification
Modified: section 4.1.7 Bluetooth Menu > Security – max. 16 characters for PIN
Modified: section 1.3.9 Reader – RFID (add ICODE)
Modified: section 2.5.2 Front Panel (LEDs of cradle)
New: section 4.1.8(2) System Menu > IR Network Menu
Modified: section 1.3.9 Reader – RFID
Modified: section 4.1.1 Information – add RFID version
FCC Regulations – Class B statement
Modified: section 1.3.9 Reader – Symbologies Supported & Enabled
Company name changed to CIPHERLAB CO., LTD. since April 2006
New: Safety Precaution
Modified: Care & Maintenance
Modified: section 1.2.3 Dimensions & Specifications
Modified: section 1.3.4 Keypad – Screen Icons
Modified: section 1.3.5 LCD – Screen & Backlight Settings
Modified: section 1.3.12 Application Software to include AG and CipherNet
Modified: sections 2, 2.5 ~ 2.7
Modified: sections 3.1 & 3.3
Modified: section 4.1.2 Screen Calibration
Modified: section 4.1.6 Load Program via Bluetooth
Update drawings
Load Program via Bluetooth
Official release
C H A P T E R 1
Introduction
3
This chapter mainly explains the hardware parts and features of the 8500 Series Mobile
Computer.
The 8500 family includes:
8500
8570
8580
8590
Bluetooth Class 2
Bluetooth Class 2 + 802.11b/g
Bluetooth Class 2 + GSM/GPRS
Bluetooth Class 2 + 802.11b/g + GSM/GPRS
In This Chapter
1.1 Inside the Package ....................................................... 3
1.2 Options......................................................................... 4
1.3 Product Highlights....................................................... 4
1.4 Nomenclature............................................................... 5
1.5 Features........................................................................ 8
1.1 Inside the Package
The following items are included in the package. Save the box and packaging material for future use in case you need to store or ship the mobile computer.
8500 Series Mobile Computer
Rechargeable Li-ion battery pack
Stylus
Hand strap
Software & Manual CD
Note: For battery charging, you will need to purchase a charging cradle separately.
4 8500 Series Series Reference Manual
1.2 Options
Rich choices of optional accessories are available for you to enhance the total performance of the mobile computer.
Pistol Grip (detachable)
Belt Holster
Protective Cover
Memory Card, 4 or 8 MB
Spare rechargeable Li-ion battery
4-slot Battery Charger
Charging & Communication Cradle
Modem Cradle
Ethernet Cradle
Bluetooth Access Point
802.11b/g Access Point
1.3 Product Highlights
Ergonomic design - ruggedized yet streamlined, with hand strap for secure hold.
Built tough to survive harsh environments - splash, dust & drop resistant.
Upgradeable memory - optional memory card adds up to 10 MB for data storage.
Dual mode support - 1D / 2D scan engine plus RFID reader.
Total wireless solution - connectivity includes IR / IrDA, Bluetooth, 802.11b/g and
GSM/GPRS.
Large graphic monochrome LCD touch screen supports double-byte characters and bitmap graphics. The touch screen featuring signature capture can be activated with its stylus or a finger, software programmable.
Programmable feedback includes buzzer, LED indicator, and vibrator.
Quick link to any backend database through Windows-based CipherNet programs for
VT100/220 and IBM 5250 emulation.
Easy customization of AG applications through Windows-based Application Generator
(AG) programs for preloaded AG Runtime.
Programming support includes BASIC & C compilers.
1.4 Overview
1.4.1 Nomenclature
Chapter 1 Introduction 5
Figure 1: Nomenclature (front & back)
6 8500 Series Series Reference Manual
1.4.2 Accessories & Peripherals
Figure 2: Nomenclature of accessories
1.4.3 Dimensions
Chapter 1 Introduction 7
Figure 3: Dimensions
8 8500 Series Series Reference Manual
1.5 Features
1.5.1 Power
Main Battery
The 8500 Series is powered by a rechargeable 3.7 V/4000 mAh Li-ion battery pack, and it takes approximately four hours to fully charge it.
For power-saving purpose, always turn off the backlight while working in a well-lit area.
When the backlight is on for extended periods of time, the main battery will become low sooner than expected.
The smart battery icon on the LCD screen shows the status of power consumption. There are two ways to monitor a low battery charge or discharged battery from the screen.
Examine the level of the 4-bar battery icon
Monitor voltage level (see section 4.1.5 Power
)
Backup Battery
In addition, one 3.0 V/7 mAh rechargeable Lithium button cell on the main board retains data in SRAM and maintains the running of the real-time clock and calendar. It takes at least twenty-four hours to fully charge the backup battery.
For a fully charged backup battery, it can last for at least one week. However, it is not necessary to fully charge the backup battery for the mobile computer to work.
Monitor voltage level (see section 4.1.5 Power
)
Initial Charging
The main battery must be fully charged before using the mobile computer for the first time.
Because the internal backup battery is constantly charged from the main battery, the initial charging requires installing the battery pack to the mobile computer and then seating the mobile computer in the cradle for charging. This will have both the main and backup batteries charged at the same time.
Note: For initial charging, it takes approximately 4 hours to fully charge the main battery.
Chapter 1 Introduction 9
Caution of Low Battery Charge
The battery pack is the only power source for the mobile computer to work. It also charges the backup battery on the main board so that the data stored in SRAM can be retained properly. Therefore, when the main battery charge goes low, replace the battery pack with a charged one or charge it as soon as possible. And, always save data before it is too late.
Warning: Data loss may occur with SRAM during low battery condition. Always save data before running out of power or keep a fresh battery for replacement.
1.5.2 CPU
A 16-bit CMOS type CPU is utilized, low power consumption.
1.5.3 Memory
The collected data can be sent back to a host computer immediately or stored in memory
(SRAM).
Program Memory
2 megabytes flash memory for core, OS, application programs, fonts, etc.
Data Memory
2 megabytes SRAM with contents backup by a 7 mAh rechargeable Lithium button cell.
An optional memory card provides additional 4 or 8 megabytes.
Calendar
A calendar chip is equipped for accurate time/date logging.
Caution of Data Loss
When the main battery is removed or drained, the backup battery on the main board is to retain the contents of SRAM and maintain the running of the calendar for at least one week, on condition that the backup battery has already been fully charged.
10 8500 Series Series Reference Manual
If you want to put away the mobile computer for a couple of days, you should be aware that data loss occurs when both the main and backup batteries discharge completely. Therefore, it is necessary to save data in a host computer before putting away the mobile computer!
1.5.4 Keypad
The mobile computer can be equipped with a keypad of 24 keys or 44 keys for system setup, user entry and so on. The keypad comes with programmable LED backlight, like the screen.
for screen & backlight settings.
Silicon rubber has been chosen for their durability and prompt feedback. The key click can be configured through programming or the System Menu .
Screen Icons
When any of the following icons appears on the screen, it indicates a certain mode is activated. It means holding down the specific key is unnecessary. Simply press another key or red-coded function key ([F1] ~ [F12]) to produce a result.
24-key
A / a:
:
Press [Alpha] to enter the alphabetic mode, capital or small letters.
Press [FN] to enter the function mode.*
44-key
:
:
:
Press [Shift] to enter the special function mode.*
By default, it is the toggle of capital/small letters.
Press [RED] to enter the function mode.*
Press [Alt] to enter the special function mode.*
Note: When pressing these (special) function keys, the system will send the associated key codes to the application program, and it is up to the application program to interpret the key codes.
Chapter 1 Introduction 11
24-key layout
The layout of the 24-key keypad is similar to that of a telephone, which consists of an alphanumeric keypad and assorted characters.
This keypad is set to numeric mode by default.
For alpha mode, simply press [ALPHA] to toggle between alpha and numeric modes.
Figure 4: 24-key layout
12 8500 Series Series Reference Manual
44-key layout
The layout of the 44-key keypad includes numeric, alphabetic, assorted characters, function and modifier keys.
Figure 5: 44-key layout
Chapter 1 Introduction 13
For the 44-key keypad, these keys can be categorized into the following groups by color:
Blue Area:
Two [Enter] keys: user-friendly and convenient for either right-handed or left-handed operator to perform general function of a [Enter] key.
It can be used together with [RED] modifier key: [Enter] + [RED] = alternately turn ON/OFF the backlight of LCD and keypad.
Black Area:
Power key
Numeric keys
Modifier keys: [Shift] or [Alt] that modifies its next key. The functionality depends on software application.
Others like [Backspace], [ESC], [Space], [Tab], [Insert], [Delete], [ - ], [ . ]
Yellow Area:
[Scan] button
Navigation keys for moving the cursor up, down, left, right.
Alphabetic keys
Others like punctuation keys for comma & semi-colon, dollar & colon.
Red Area:
[RED] modifier key: the solid red key next to the Power key
[RED] followed by one red-coded key: The [RED] modifier key modifies (activates) the second key. Its functionality is determined by the red-coded key, which is specified by red letters under the navigation keys or on top of alpha keys and some punctuation keys.
14 8500 Series Series Reference Manual
1.5.5 LCD
The mobile computer comes with a 3” FSTN graphic LCD, 160 by 160 pixels resolutions, which can be programmed to display text or graphics, such as specific font and company logo, to meet varying application needs.
Options
English font
Font Size (pixels)
Font size 6×8 (pixels)
Font size 8×16 (pixels)
Font size 16×16 (pixels) Chinese font
Other language fonts, company logo…
Programmable
Characters by lines
26 characters by 19 lines
20 characters by 9 lines
10 characters by 9 lines
Note: Normally, the bottom line (ICON_ZONE) is reserved to display status icons, such as the battery icon.
Screen & Backlight Settings
The backlight of screen and keypad helps ease reading under dim environments. Relevant settings can be configured or adjusted by pressing the following key combinations (you may press and hold the function key, and then, press the second key):
Settings
Backlight ON/OFF
Backlight Intensity
LCD Contrast
22-key
[FN] + [Enter]
44-key
[RED] + [Enter]
[FN] + [Left] or [FN] + [Right] [RED] + [Left] or [RED] + [Right]
[FN] + [Up] or [FN] + [Down] [RED] + [Up] or [RED] + [Down]
Touch Screen & Signature Capture
This LCD is also a touch screen, which enables the use of a stylus for handwriting. It also features signature capture that can save signature as confirmation of receipt when delivering goods to door.
Refer to section 4.1.2 Settings for screen & contrast calibration.
Warning: DO NOT use any pointed or sharp objects to move against the surface of the screen.
Chapter 1 Introduction 15
1.5.6 Status LED
The dual-color LED above the [Scan] trigger can be programmed to provide information that helps diagnosing.
For example, if you are using AG Runtime , you will be informed of the scanning result immediately by this LED indicator:
Red LED - Error
Green LED - Good Read
1.5.7 Buzzer
The buzzer is a low power transducer type and can be programmed for status feedback. Its pitch and duration are software programmable.
1.5.8 Vibrator
The mobile computer is integrated with a vibrator. It is software programmable and especially useful when working in a noisy environment.
16 8500 Series Series Reference Manual
1.5.9 Reader
A wide variety of scan engines is available for delivering flexibility to meet different requirements.
Types of Reader
1D Barcode Reader
2D Barcode Reader
RFID
Scan Engine
CCD (Long Range Imager)
Laser scan engine
Long Range Laser scan engine
Extra Long Range Laser scan engine (with aiming beam)
2D scan engine
Tags supported include:
Standard
ISO 14443A
ISO 14443B
ISO 15693
Labels
Mifare Standard 1K
Mifare Standard 4K
Mifare Ultralight
Mifare DESFire
Mifare S50
SLE44R35
SLE66R35
SRIX 4K
ICODE SLI
SRF55V02P
SRF55V02S
SRF55V10P
TI Tag-it HF-I
ICODE ICODE ® (Phillips)
Dual Mode Support
The mobile computer allows the co-existence of one integrated scan engine and the RFID reader.
Symbologies Supported & Enabled
The supported symbologies depend on the scan engine you use; some of the supported symbologies must be enabled through programming if not enabled by default.
CCD / Laser scan engine
Symbologies
Codabar
Industrial 25
Interleaved 25
Matrix 25
Code 39
Italian Pharmacode
CIP 39
Code 93
Code 128
Chapter 1 Introduction 17
(Also Known As)
(NW7)
No
Yes
No
(French Pharmacode) No
Yes
Yes
Enabled by default
Yes
Yes
Yes
EAN-8
EAN-8 with Addon 2, Addon 5
EAN-13 with Addon 2, Addon 5
UPC-A with Addon 2, Addon 5
UPC-E0/UPC-E1 with Addon 2, Addon 5
Yes
Yes
Yes
Yes
Yes
18 8500 Series Series Reference Manual
Long Range Laser scan engine
Symbologies:
Interleaved 25
Discrete 25
IATA (25)
Code 39
Code 39 Full ASCII
Trioptic
Code 93
Code 128
ISBT 128
RSS Limited
RSS Expanded
UPC-E with Addon 2, Addon 5
EAN-8 with Addon 2, Addon 5
EAN-13 with Addon 2, Addon 5
Bookland (EAN)
UPC-A
UPC-A with Addon 2, Addon 5
UPC-E1 with Addon 2, Addon 5
Enabled by default
(Industrial 25)
Yes
Yes
(Variant of Code 25) Yes
Yes
Yes
(Variant of Code 39) Yes
Yes
Yes
Yes
(UPC-E0)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Chapter 1 Introduction 19
1.5.10 Wireless Support
The 8500 Series supports state-of-the-art wireless technologies so that it can send / receive data in real time in an efficient way.
WPAN: Infrared (IR / IrDA) technology for data exchange, embedded
WPAN: Bluetooth technology for cable replacement & data exchange, embedded
WLAN: IEEE 802.11b/g for wireless networking, optional
WWAN: GSM/GPRS for short message service, optional
Generally, the coverage of each technology can be viewed as follows.
Figure 6: Coverage of wireless technologies
20 8500 Series Series Reference Manual
IR / IrDA
The mobile computer has an integrated IR port on the bottom, which can directly establish connection with an IR device for printing or data exchange. Simply have the IR port of the mobile computer toward the IR port of the target device.
This IR port supports CipherLab proprietary IR communication protocol and standard
IrDA protocol.
IrDA specification defines communications (transmit/receive data) between two IrDA enabled devices within a short range, line-of-sight.
IR / IrDA Specifications
Infra Red:
Data Rate:
Connected devices:
Coverage:
Standard:
Optical
Up to 115200 bps
Peer-to-Peer
From contact to 30 cm, line-of-sight
CipherLab proprietary protocol and IrDA 1.0
Chapter 1 Introduction 21
Bluetooth Class 2
Bluetooth technology is for cable replacement & data exchange. With built-in Bluetooth module, the 8500 Series can directly communicate with any Bluetooth enabled device, not necessarily line-of-sight.
Serial Port Profile (SPP) is for ad-hoc networking, without going through any access point.
Dial-Up Networking Profile (DUN) makes use of a Bluetooth modem or mobile phone as a wireless modem.
Also, it can be used to activate the GPRS functionality on a mobile phone.
Human Interface Device Profile (HID) allows a terminal to work as an input device, i.e. keyboard, for a host computer.
Personal Area Networking Profile (PAN) makes use of Bluetooth Network
Encapsulation Protocol (BNEP) for IP networking over Bluetooth. Access points (AP) are required.
Bluetooth Specification
Frequency Range: 2.4 GHz
Data Rate: 433 kbps
Connected Devices: 1 for DUN mode
Up to 7 for SPP or PAN mode (AP required)
Profiles:
Coverage:
SPP, DUN, PAN
Class 2 – 10 meters line-of-sight
Max. Output Power: Class 2 – 6 mW
Spread Spectrum: FHSS
Modulation:
Standard:
GFSK
Bluetooth version 1.1
22 8500 Series Series Reference Manual
IEEE 802.11b/g
Model 8570/8590 can easily connect to legacy networks through access points (APs).
Roaming among different networks is possible.
IEEE 802.11b/g is an industrial standard for Wireless Local Area Networking (WLAN), which enables wireless communications over a long distance.
The speed of connection between two wireless devices will vary with range and signal quality. To maintain a reliable connection, the data rate of the 802.11b/g system will automatically fallback as range increases or signal quality decreases.
802.11b/g Specification
Frequency Range:
Data Rate:
2.4 GHz
802.11b – 1, 2, 5.5, 11 Mbps
802.11g – 6, 9, 12, 18, 24, 36, 48, 54 Mbps
Connected Devices: 1 for ad-hoc mode (No AP)
Profiles:
Standard:
Multiple for infrastructure mode (AP required)
IP/TCP/UDP
Coverage: 350 meters line-of-sight
Max. Output Power: 50 mW (802.11b)
Spread Spectrum: DSSS
Modulation: 802.11b – DBPSK (1 Mbps), DQPSK (2 Mbps), CCK (5.5 & 11 Mbps)
802.11g – OFDM
IEEE 802.11b/g, interoperable with Wi-Fi devices
Chapter 1 Introduction 23
GSM/GPRS
Model 8580/8590 is capable of data communications over free air, right on the road.
GSM and GPRS are industrial standards for Wireless Wide Area Networking
(WWAN), which enables wireless communications over free air.
“GSM” is an abbreviation of Global System for Mobile Communications.
“GPRS” is an abbreviation of General Packet Radio Service.
GPRS, a packet-switched technology based on GSM (circuit-switched), allowing information to be transmitted or received more quickly, immediately and efficiently across the mobile network. GPRS Class B mobile devices can be attached to both GSM and GPRS services, using one service at a time.
24 8500 Series Series Reference Manual
1.5.11 Resistance
Impact
The mobile computer is designed for harsh industrial environments, and is proved to survive drop test by the following criteria:
Surface Type
Concrete
Distance to Surface
1.5 meters
Drop Times
5 drops per 6 sides
Splash & Dust
The mobile computer is sealed against moisture and dust to industry standard IP 64.
6 = Totally protected against dust
4 = Protection against water sprayed from all directions, i.e. limited ingress is permitted.
1.5.12 Application Software
Application Generator (AG)
For easy development of applications, the mobile computer ships with development tools on the CD-ROM. It includes Windows-based Application Generator programs, batch and
WLAN, as well as relevant utilities.
Terminal Emulation
The mobile computer supports VT100/220 and IBM 5250 terminal emulation for accessing a backend database. The Windows-based CipherNet programs are available on the
CD-ROM.
1.5.13 Programming Support
For developing custom applications, CipherLab provides BASIC and C compliers through licensing.
C H A P T E R 2
Installation
25
The mobile computer is designed for portable use, and it almost requires no installation except installing the battery pack and necessary auxiliary parts.
before installation.
In This Chapter
2.1 Installing the Battery Pack........................................... 26
2.2 Installing the Hand Strap ............................................. 27
2.3 Installing the Pistol Grip.............................................. 28
2.4 Installing SIM Card for GSM/GPRS Network ............ 29
2.5 Setting up the Cradle ................................................... 30
2.6 Battery Charger............................................................ 34
26 8500 Series Series Reference Manual
2.1 Installing the Battery Pack
Always prepare a spare battery pack, especially when you are on the road. To save power, turn off the backlight when you are working in a bright work area.
1. Place the mobile computer face down on a flat and clean surface.
2. Slide the battery pack into the battery compartment at a proper angle (30°~45°) so that the tabs on the bottom of the battery are hooked in the grooves of the compartment.
Make sure that the battery is snugly fit into the compartment.
3. Hold the mobile computer still and slide the battery latch to lock the battery in the compartment.
Note: For a new battery, make sure it is fully charged before use.
Figure 7: Installing battery pack
Chapter 2 Installation 27
2.2 Installing the Hand Strap
The hand strap is ideal for one-handed operation, which requires safe and convenient hold of the mobile computer. Always make sure the hand strap is well hooked and screwed to the back of the mobile computer.
When a hand strap is necessary, install it to the mobile computer by following these steps:
1. Place the mobile computer face down on a flat and clean surface.
2. Screw one end of the hand strap to the shield-like cover on the back of the mobile computer.
3. Insert and hook the other end of the hand strap to the bottom of the mobile computer.
4. Make sure the hand strap is securely attached to the mobile computer.
5. Adjust the length of the hand strap to suit your handbreadth.
Figure 8: Installing hand strap
28 8500 Series Series Reference Manual
2.3 Installing the Pistol Grip
This contoured pistol grip enables intuitive trigger-and-scan operation, which is very helpful in scan intensive applications.
When a pistol grip is necessary, install it to the mobile computer by following these steps:
6. Place the mobile computer face down on a flat and clean surface.
7. Remove the shield-like cover on the back of the mobile computer by unscrewing.
If there is a hand strap installed, remove it first. Keep the cover and screws for future use when the pistol grip is not desired.
8. Connect the power connector from the pistol grip to the receptacle on the mobile computer.
9. Screw the pistol grip to the shield-like cover.
10. Make sure all screws are tightened up.
11. Turn on the mobile computer and test the trigger.
Figure 9: Installing pistol grip
Chapter 2 Installation 29
2.4 Installing SIM Card for GSM/GPRS
Network
When GSM/GPRS networking is required, insert the SIM card by following these steps:
1. Unscrew the four screws of the top enclosure on the mobile computer.
2. Take out the GSM/GPRS card from the mobile computer.
3. Insert your SIM card on the GSM/GPRS card.
4. Put the GSM/GPRS card back to the mobile computer.
5. Screw the top enclosure tightly.
Figure 10: Inserting SIM card
30 8500 Series Series Reference Manual
2.5 Setting up the Cradle
You may choose an appropriate cradle that best suits your needs.
1. Place the cradle on a flat and clean surface.
2. Connect the line of the power adaptor to the power jack on the back of the cradle.
3. Connect the power adaptor to a suitable power outlet.
4. The cradle is ready for charging.
5. Seat the mobile computer in the cradle.
If data communications are desired at the same time, you can establish a proper connection with a computer or remote host. Refer to the Installation Guide of your cradle.
Figure 11: Setting up cradle
2.5.1 Cradle Options
The following cradle types are available on order:
Cradle Type
POWER Jack
RS-232 Port
Serial Cradle
√
√
Modem Cradle
√
√
Ethernet Cradle
√
√
Chapter 2 Installation 31
Line Jack
Phone Jack
RJ-45 Port
DIP Switch
IP Reset Switch
−
−
−
−
−
√
√
−
−
− √
√ (RS-232/Modem) √ (Auto/LAN)
− √
Delivering flexibility in making a connection, the Modem Cradle integrates the modem functionality (56 kbps) on the Serial Cradle. You may choose to use the modem or RS-232 port by sliding the DIP switch.
Note: Refer to the Ethernet Cradle manual for more information.
2.5.2 Front Panel
For charging status of the loaded battery in the mobile computer, view the device screen.
Figure 12: Cradle LEDs
Front Panel LEDs Tasks
:
Spare battery charging status
Indication of connection status
Solid red Charging
Solid green Charging done
Flashing (red/green) Error occurs
RX: Receiving status
Solid red Receiving data from Ethernet or host
32 8500 Series Series Reference Manual
TX:
POWER:
Transmitting status
Line status
Solid red
Solid red
Solid green
Transmitting data to Ethernet or host
Modem/Ethernet connection
Direct connection via RS-232
Warning: Charging error may occur due to a power failure or defected battery contacts.
2.5.3 Back Panel
Figure 13: Cradles –Back panel
Chapter 2 Installation 33
Modem Cradle: DIP Switch
Modem Connection
To use the modem functionality, slide the DIP switch to right:
When the power cable is properly connected, the LED light of POWER on the front panel will be solid red.
RS-232 Connection
To use the RS-232 port, slide the DIP switch to left:
When the power cable is properly connected, the LED light of POWER on the front panel will be solid green.
Ethernet Cradle: DIP Switch
Auto-detect Connection
Slide the DIP switch to left:
The RS-232 connection will override Ethernet connection when both are present. However, you can use cradle commands to switch in between the two.
When the power cable is properly connected, the LED light of POWER on the front panel will be solid green.
LAN Connection
Slide the DIP switch to right:
Only the Ethernet connection can be established. However, you can use cradle commands to switch in between the two.
When the power cable is properly connected, the LED light of POWER on the front panel will be solid red.
34 8500 Series Series Reference Manual
2.6 Battery Charger
If you have purchased the 4-slot battery charger, you can charge up to four batteries at the same time. This is particularly convenient for a non-stop operation or locations where a proper power supply is unavailable.
Note: It takes approximately 4 hours to fully charge the battery pack.
C H A P T E R 3
Software Architecture
35
In This Chapter
3.1 Overview ..................................................................... 35
3.2 System Configuration .................................................. 36
3.3 Application Programs .................................................. 37
3.1 Overview
The software inside the mobile computer consists of three modules: Kernel, System, and
Application Program.
Figure 14: Software Architecture
36 8500 Series Series Reference Manual
3.2 System Configuration
For managing system configurations and multiple programs, each mobile computer comes with the System Menu , Kernel , and Program Manager .
System Menu
The System Menu is bundled with BASIC Runtime or user programs that are written in “C”.
It is for system configuration, functionality testing, downloading font file and program.
Kernel
Kernel is the innermost core of the OS. It provides services for downloading the active application program or font file, updating the kernel or the active application program, and configuring Bluetooth settings.
Program Manager
The Program Manager is part of the kernel. You may download as many as seven application programs, or six programs plus one font file.
Chapter 3 Software Architecture 37
3.3 Application Programs
3.3.1 Application Generator (AG)
The mobile computer is preloaded with CipherLab application program, AG Runtime . When you turn on the mobile computer, it displays the Main Menu of AG application.
Before using the mobile computer to collect data, you need to configure the application with the companion tool on your computer. This time-saving development tool helps create application templates on your computer. For details on the AG application, please refer to separate user manual.
Application Generator
Batch AG
RF AG
AG Runtime Companion Tool on PC-End
U8500*.SHX AG8500.exe
U85WLAN*.SHX AG8500WLAN.exe
Note: The Application Generator (AG) software package includes
(1) a companion tool for quickly developing your application, i.e. AG or RF AG;
(2) several associated utilities to make it versatile in use.
3.3.2 CipherNet
Instead of Application Generator , you may download the terminal emulation program, i.e.
CipherNet Runtime
, to the mobile computer. Refer to section 4.1.6 Load Program
. Then, run individual companion tool on your computer.
For details on the CipherNet application, please refer to separate user manual.
Terminal Emulation
VT100/220
IBM 5250
CipherNet Runtime Companion Tool on PC-End
85xx-VT.SHX CipherNet-VT.exe
85xx-5250.SHX CipherNet-5250.exe
3.3.3 User Program
You may need to develop your own application program in BASIC or C. For detailed information, please contact CipherLab Co., Ltd.
38 8500 Series Series Reference Manual
C H A P T E R 4
Configuration
39
This section mainly describes how to configure the 8500 Series Mobile Computer, regarding system configurations and program download.
When a menu is displayed, you may select an item by either of the following ways:
using the [UP] and [DOWN] keys to move the highlight bar
pressing the number key that corresponds to the item number
using the stylus to touch that item or the item number
On each screen, the bottom line displays status icons, such as:
The 4-bar battery icon indicates the current power status.
When a turn-page icon ( menu.
) is displayed, it indicates there is a previous page or
To return to a previous page or menu, you may press [ESC], touch the menu title, or follow the on-screen instructions.
In This Chapter
4.1 System Menu ............................................................... 40
4.2 Program Manager ........................................................ 77
4.3 Kernel Menu ................................................................ 82
40 8500 Series Series Reference Manual
4.1 System Menu
The System Menu is generated by a powerful utility, which offers an interface for engineers
(programmers or system integrator) to view system information, change the configuration parameters, download programs and run diagnostics.
This menu is designed for engineering tests and maintenance ONLY. For this reason, the
System Menu provides password protection to prevent unauthorized users from accidentally changing system settings.
Warning! The System Menu is NOT for the use of any end users. The system password helps ensure system safety and integrity.
How to access the System Menu?
1. Turn off the mobile computer.
2. Press [7] + [9] + [Power].
Chapter 4 Configuration
4.1.1 Information
Here provides important system information to help diagnose the system.
41
System Menu > 1. Information
H/W Hardware version (PCB)
S/N A serial number assigned to the mobile computer
M/D
KNL
Manufacturing date
Kernel version
LIB
BSC
USR
DEV
RFID
C library version
BASIC Run-time version, if a BASIC application is downloaded
Application program version
5-digit code for optional hardware configurations
For example, 1710-1 indicates the 44-key mobile computer is equipped with
CCD scan engine, RFID reader, and 802.11b/g and GSM/GPRS connectivity.
RFID module version if present; the 3 rd digit of the above Device Code must be 1
Understanding Device Code
Device Code Modular Component
1st digit Reader module
Types
0= No reader
1= CCD scan engine
2= Laser scan engine
3= 2D scan engine
4= Long Range Laser scan engine
5= Extra Long Range Laser scan engine
42 8500 Series Series Reference Manual
2nd digit Wireless module 3= Bluetooth + GSM/GPRS
4= Bluetooth + 802.11b/g
5= Bluetooth only
7= Bluetooth + GSM/GPRS + 802.11b/g
0= none
1= RFID reader
0
0= 24-key
1= 44-key
3rd digit RFID module
4th digit
5th digit
Reserved
Keypad module
4.1.2 Settings
You can change the default settings here.
Chapter 4 Configuration 43
System Settings
Clock
Backlight Period
Auto Off
Power On Options
Key Click
System Password
Font
Reset to Default
Reset Reader
LCD Heater
Default Values blank
20 seconds, Level 2
10 minutes
Program Resume
Tone 2
Open access
System font
Factory settings
Factory settings of 2D or (Extra) Long Range Laser scan engine
Disabled
Settings > Clock
Set date and time for Real Time Clock. Enter two digits for the year, i.e. 04 for 2004.
Settings > Backlight Period
Set the backlight duration for the keypad and LCD.
Enter a value between 0 and 9999.
Use the [UP] and [DOWN] keys to adjust the backlight level.
44 8500 Series Series Reference Manual
Settings > Auto Off
The mobile computer will be turned off automatically when no operation is taking place during a specified period of time. Enter a value between 0 and 999.
Note: To disable this function, enter 0.
Settings > Power On Options
Set the startup screen once the mobile computer is turned on:
[0] Program Resume: computer is turned off.
[1] Program Restart:
Start from the last session of program before the mobile
Fresh start from the first session of the program.
Settings > Key Click
The system will produce an audible signal when any key on the keypad is pressed.
The current value is highlighted. Select a desired tone for the buzzer or mute it.
Settings > System Password
Set a password to control user access to the System Menu . The password can be up to eight alphanumeric characters.
Note: The password is case-sensitive. To disable a previous password, enter blank on the
"Input new password" and "Verify password" screens.
Settings > Font
Font version information can be viewed here. It displays System Font if there is no custom font file.
If a multi-language font file is downloaded, you will be able to select a font from the list.
Chapter 4 Configuration 45
Settings > Screen Calibration
The cross mark will appear on the four corners of the screen for alignment. Use the tip of the stylus to tap at the center of the cross mark firmly and accurately.
To start with contrast calibration, press [1]+[9] simultaneously. Refer to section
for screen & backlight settings.
Warning: DO NOT use any pointed or sharp object to move against the screen.
Settings > Reset to Default
Reset system settings to the default values, except for the reader settings.
Settings > Reset Reader
You may reset the reader settings to the default values when one of the following scan engines is installed for use:
2D scan engine
Long Range Laser scan engine
Extra Long Range Laser scan engine
Settings > LCD Heater
Set the heater functionality. When enabled, it will start to heat when the environmental temperature falls below -10 Celsius degrees.
46 8500 Series Series Reference Manual
4.1.3 Tests
Here provides functional tests for key parts.
Tests > Reader
Test the reading performance of the scanner. Press [SCAN] to start. To stop and exit the test, press any key.
Note: The supported symbologies depend on the scan engine you use, and some of them are not enabled by default.
Tests > Buzzer
Test the buzzer with different frequency/duration combinations. Press [Enter] to start. To stop and exit the test, press any key.
Tests > LCD & LED
Test the LCD display and LED indicator. Press [Enter] to start. To stop and exit the test, press any key.
Tests > Keyboard
Test the rubber keys. Press any key and its corresponding character will be shown on the screen. To stop and exit the test, press [ESC].
Chapter 4 Configuration 47
Tests > Memory
Test the data memory (SRAM), and the results will be shown on the screen. To stop and exit the test, press [ESC].
Warning! The contents of the data memory (SRAM) will be wiped out after test.
Tests > Touch Screen
Test signature capture by using the stylus for handwriting. Press [Enter] to start. To stop and exit the test, press [ESC].
Tests > Vibrator
Test the vibrator. To stop and exit the test, press [ESC].
Tests > Echo Test
After a physical connection is established properly, run the utility “Echo Test” on your computer and start this test on your mobile computer. Select a desired baud rate. To stop and exit the test, press [ESC].
IR (Cradle-IR):
This echo test is to verify connectivity via IR between the mobile computer and any cradle.
MODEM:
This echo test is to verify connectivity via modem. A telephone line must be connected to the Modem Cradle.
Note: For the Modem Cradle, any value other than 57600 bps (default) must be configured through the DIP switch on the IR control board.
Tests > RFID
Test the reading performance of the RFID reader when a proximity card is present. To stop and exit the test, press [ESC].
48 8500 Series Series Reference Manual
4.1.4 Memory
Here provides information and initialization function of the memory.
Memory > Size information
Base RAM
Memory Card
(onboard SRAM for data memory)
(SRAM for data memory)
Flash (for memory)
Memory > Initialize
Initialize the data memory, Base RAM or Memory Card.
Warning! The contents of the data memory (SRAM) will be wiped out after memory initialization.
4.1.5 Power
Here shows current voltage consumption.
Chapter 4 Configuration 49
Main (battery):
It shows dynamic status of the battery pack, which is used as the main power source.
Backup (battery):
It shows dynamic status of the button cell, which is used to retain data in SRAM.
Warning! Always examine the battery icon on the device screen so that you will be alerted for a low battery condition.
50 8500 Series Series Reference Manual
4.1.6 Load Program
Here you can access the
Load Program service provided by the kernel which will take over
the job, and therefore, you will not be able to return to the System Menu by pressing [ESC].
After downloading, restart the mobile computer to activate the new program.
.SHX Program
Program File
Font File
Download one of the following C program files and/or one font file:
AG Runtime (U*.shx)
CipherNet Runtime (85xx-5250.shx, 85xx-VT.shx)
BASIC Runtime* (BC*.shx)
User program
Refer to the Font Files folder on CD-ROM.
If you have downloaded a BASIC Runtime program, the next time you enter the Load
Program submenu you will be able to select whether to download a C program (.SHX) or
BASIC program (.SYN).
Note: “Load Basic” menu is only available after you have downloaded a BASIC Runtime program.
Chapter 4 Configuration 51
4.1.7 Bluetooth Menu
This submenu is for the built-in Bluetooth module to work with other Bluetooth enabled devices. You must configure these parameters correctly.
Bluetooth Settings
Connect Setting
Local Name
Remote Name
Broadcast Me
Power Saving
BT-GPRS AP Name
Security
Authentication
PIN Code
Network Setting
DHCP
SubNet Mask
Local IP Address
Default Gateway
DNS Server
Domain Name
Default Value
Model no. + Serial no.
--- v v
SPP DUN
Items Need to Be Checked v v
Enabled
Enabled
--- v v
--- v v
(v)*
Disabled
---
Enabled
255.255.128.0
0.0.0.0
0.0.0.0
0.0.0.0
---
---
---
---
---
---
--- v v
---
---
---
---
---
--- v v
Note: GPRS AP name is ONLY required for DUN-GPRS mode.
PAN v v v v v v v v v v v v
---
52 8500 Series Series Reference Manual
Bluetooth Menu > Information
Information of network configuration can be viewed here.
Bluetooth Menu > 1. Information
LIB C library version
MAC
IAM
MAC ID of the Bluetooth module
CTY
A name given to the mobile computer for identification.
By default, it is made up of model No. and the serial number. (Identical to 2.
Connect Set > 1. Local Name)
"Normal" means all 79 channels are available for frequency-hopping
(There are bandwidth limitations for 2.4 GHz ISM band in some countries. For example, only 23 RF channels are defined instead of 79 RF channels in Japan, Spain and France.)
DHCP DHCP server in use or not
IP IP address of the mobile computer
Mask Subnet Mask
Gate Default Gateway
Chapter 4 Configuration 53
Bluetooth Menu > Connect Setting
A basic Bluetooth system can be configured as (1) point to point - DUN mode, and (2) point to multi-point - SPP or PAN mode.
Set the following parameters if necessary.
Bluetooth Menu > 2. Connect Set
1. Local Name Enter a name for identifying the mobile computer.
By default, it is made up of model No. and the serial number.
2. Remote Name Enter a name for making a specific connection.
The remote name must be one of those in the Freq. Dev. List. Otherwise, the mobile computer will fail to make a connection with any device without pairing.
DO NOT specify any remote name when roaming across different groups of APs is required.
3. Broadcast Me
4. Power Saving
Options - Enable or Disable
For initial connection, broadcasting must be enabled so that other
Bluetooth devices can discover the mobile computer.
For security concerns, you may disable it in future use to hide the mobile computer from other Bluetooth devices.
This refers to the low power consumption mode.
5. BT-GPRS AP
Name
Options - Enable or Disable (Only the Sniff mode is supported.)
For DUN-GPRS mode, enter the AP name for connecting to the content server.
54 8500 Series Series Reference Manual
Bluetooth Menu > Security
Set or modify security parameters.
Bluetooth Menu > 3. Security
1. Authentication Options - Enable or Disable
2. PIN Code Define the encryption key values.
Up to 16 characters, using ASCII code.
Chapter 4 Configuration 55
Bluetooth Menu > Echo Tests
These echo tests are used for verifying connectivity to make sure the mobile computer is within coverage. Press [ESC] to stop and exit the test.
In PAN mode, the echo test helps measure the coverage of the range, estimate the number of
APs and mobile computers needed, and determine the topology of deploying APs.
SPP:
DUN:
Serial Port Profile
It is used for ad hoc networking, without going through any access point.
Dial-Up Networking Profile
DUN Modem - It makes use of a Bluetooth modem or mobile phone as a wireless modem.
DUN GPRS – It makes use of a mobile phone with GPRS functionality and connects to GPRS AP.
BNEP: Bluetooth Network Encapsulation Protocol
It is used by Personal Area Networking Profile (PAN) for IP networking over Bluetooth.
Bluetooth Menu > 4. Echo Tests
1. SPP Master Set the mobile computer as a master device.
1. Pairing with your computer (slave) must be completed first.
2. Run the Echo Test program on your computer. Associated settings include
- Select “RS-232” for interface.
- Use the Bluetooth COM port that has been paired.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends. The mobile computer will try to connect to PC (slave).
56 8500 Series Series Reference Manual
2. SPP Slave
3. DUN Modem
4. DUN GPRS
Set the mobile computer as a slave device.
1. Enable Authentication and set your PIN code on the mobile computer.
2. Run the Echo Test program on your computer. Associated settings include
- Select “RS-232” for interface.
- Use the Bluetooth COM port that has been configured as “outgoing”.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends.
4. The mobile computer will wait for PC (master) to start the connection.
5. Enter the preset PIN code for authentication on your computer.
The mobile computer will try to connect to a Bluetooth modem or mobile phone.
1. Pairing with your mobile phone must be completed first. Select “DialUp
Network” for Target Machine options.
2. Run the Echo Test program on your computer. Associated settings include
- Select “Modem” for interface.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends.
4. The mobile computer will connect to your mobile phone that dials up to your computer.
The mobile computer will try to connect to a mobile phone with GPRS functionality.
1. Pairing with your mobile phone must be completed first. Select “DialUp
Network” for Target Machine options.
2. Run the Echo Test program on your computer. Associated settings include
- Select “TCP/IP – Server” for interface.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends.
4. Enter the server IP on the mobile computer.
5. The mobile computer will connect to your mobile phone that dials up a
GPRS AP, and finally connect to your computer (server) through the GPRS
AP.
Chapter 4 Configuration 57
5. BNEP Client
6. BNEP Server
Set the mobile computer as a client. Enter the IP address of a server with which a connection is desired. Then, it will try to connect to an AP.
1. Pairing with an AP must be completed first. Select “Access Point” for
Target Machine options. Note that you must disable Authentication and clear the preset PIN code when connecting to Bluetooth AP (3560).
2. Run the Echo Test program on your computer. Associated settings include
- Select “TCP/IP – Server” for interface.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends.
4. Enter the server IP and port number on the mobile computer.
Set the mobile computer as a server. It will try to connect to an AP.
1. Pairing with an AP must be completed first. Select “Access Point” for
Target Machine options. Note that you must disable Authentication and clear the preset PIN code when connecting to Bluetooth AP (3560).
2. Run the Echo Test program on your computer. Associated settings include
- Select “TCP/IP – Client” for interface.
- Enter Remote IP and port number.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends.
58 8500 Series Series Reference Manual
Bluetooth Menu > Pairing Test
The pairing procedure is for the creation and exchange of a link key between two
Bluetooth-enabled devices. The devices use the link key for future authentication when exchanging information.
Bluetooth Menu > 5. Pairing Test
1. The mobile computer will first start with making an inquiry so that the system can generate a list of device(s) that has been discovered nearby.
2. Secondly, select a desired target device.
3. Then, select a Bluetooth service from the “Target Machine” menu. To stop and exit the test, press [ESC].
Serial Port (SPP)
Access Point (PAN)
DialUp Network (DUN)
4. After pairing successfully, the target device will be added to the Frequent Device List for quick connection in the future.
Note: During the initial setting of Bluetooth wireless network, the pairing procedure must be carried out before the Echo tests.
Chapter 4 Configuration 59
Bluetooth Menu > Freq. Dev. List
The Frequent Device List is used to store a list of target device(s) that the mobile computer has been connected to lately. After each successful pairing, the system will update the list.
Note: To unpair any device, simply delete the device from this list.
Bluetooth Menu > 6. Freq. Dev List
This list can show information of up to eight target devices that provides different Bluetooth services.
It can list only one device that provides the Bluetooth Serial Port service. (SPP)
It can list up to eight APs that provide the Bluetooth Personal Area Networking service. (PAN)
It can list only one device that provides the Bluetooth Dial-Up Networking service. (DUN)
Note: During roaming (for PAN only) or re-establishing the connection, the mobile computer will automatically connect to the listed AP(s) or target device without going through the pairing procedure.
60 8500 Series Series Reference Manual
Bluetooth Menu > Network Setting
Set parameters for IP networking.
Bluetooth Menu > 7. Network Setting
1. DHCP Options - Enable or Disable
2. SubNet Mask Enter a new Mask IP, if necessary.
3. Local IP Address Enter a new address for the mobile computer, if necessary.
4. Default Gateway Enter a new address for the default Gateway, if necessary.
5. DNS Server
6. Domain Name
Enter a new address for the DNS server, if necessary.
The domain name of the host is shown here when DHCP server is enabled.
Note: Normally, DHCP is enabled and all of the settings can be obtained form the DHCP server.
Chapter 4 Configuration 61
4.1.8(1) Serial PPP Menu
This submenu is for establishing a PPP connection via the Modem Cradle. You must configure these parameters correctly.
Note: Point-to-Point Protocol (PPP) is a method of connecting the mobile computer to the
Internet over serial links. It sends TCP/IP packets to a server that connects to the
Internet.
Serial PPP Menu > Information
Information of library version can be viewed here.
Serial PPP Menu > 1. Information
LIB C library version
Identical to System Menu > 1. Information
62 8500 Series Series Reference Manual
Serial PPP Menu > Connection Set
Serial PPP Menu > 2. Connection Set
1. DialUp Number Enter the number provided by your ISP.
2. Login Name Enter the login name provided by your ISP.
3. Login Password Enter the login password provided by your ISP.
4. Baud Rate Select a desired baud rate.
Note: By default, the baud rate is set to 57600 bps on the Modem Cradle.
For any other value, such as 115200/38400/19200/9600, you must configure through the DIP switch on the IR control board.
Serial PPP Menu > Echo Test
This echo test is used for verifying connectivity via Point-to-Point Protocol. For the Modem
Cradle, its physical connectivity can be verified in System Menu > Tests > Echo Test > IR or MODEM.
Serial PPP Menu > 3. Echo Test
Enter the IP address of a server with which a PPP connection is desired. Then, it will try to connect to the server.
Note: After the “PPP via IR” connection is established properly, run the utility “Echo
Test” on your computer (TCP/IP – Server), and then, start this test on your mobile computer.
Chapter 4 Configuration 63
4.1.8(2) IR Network Menu (Ethernet via IR)
This submenu is for Ethernet connection via IR networking. You must configure these parameters correctly.
Note: The Ethernet Cradle is required for establishing Ethernet connection via IR.
IR Network Menu > Information
Information of Ethernet network configuration can be viewed here.
IR Network Menu > 1. Information
DHCP DHCP server in use or not
IP
Mask
Gate
IP address of the mobile computer
Subnet Mask
Default Gateway
64 8500 Series Series Reference Manual
IR Network Menu > Network Setting
Set parameters for IP networking.
IR Network Menu > 2. Network Setting
1. DHCP Options - Enable or Disable
2. SubNet Mask Enter a new Mask IP, if necessary.
3. Local IP Address Enter a new address for the mobile computer, if necessary.
4. Default Gateway Enter a new address for the default Gateway, if necessary.
5. DNS Server
6. Domain Name
Enter a new address for the DNS server, if necessary.
The domain name of the host is shown here when DHCP server is enabled.
Note: Normally, DHCP is enabled and all of the settings can be obtained form the DHCP server.
Chapter 4 Configuration 65
IR Network Menu > Echo Tests
The Ethernet Cradle supports three working modes:
Data Mode
Modem Mode
Transparent Mode
These echo tests are used for verifying connectivity via the Ethernet Cradle. For details, refer to the Ethernet Cradle manual.
IR Network Menu > 3. Echo Tests
1. Data Mode Set the Ethernet Cradle in Data mode. The mobile computer works as a client. .
2. Modem Mode Set the Ethernet Cradle in Modem mode. The mobile computer works as a client.
3. Transparent Mode 1. Client Mode - Set the mobile computer as a client. Enter the IP address of a server with which a connection is desired.
2. Server Mode - Set the mobile computer as a server that waits for other devices to connect to.
Note: After the “Ethernet via IR” connection is established properly, run the utility “Echo
Test” on your computer (TCP/IP – Server or Client), and then, start this test on your mobile computer.
66 8500 Series Series Reference Manual
4.1.8(3) Wi-Fi Menu
This submenu is for 802.11b/g wireless networking. You must configure these parameters correctly.
Note: This submenu is generated only when the Wi-Fi module is present.
Wi-Fi Settings
Network Setting
DHCP
SubNet Mask
Local IP Address
Default Gateway
DNS Server
Domain Name
WLAN Setting
Local Name
SS ID
System Scale
Power Saving
Preamble
Ad-Hoc
Security
Authentication
WEP Menu
EAP Menu
Default Value
Enabled
255.255.128.0
0.0.0.0
0.0.0.0
0.0.0.0
---
Model no. + Serial no.
---
Medium
Enabled
Long
Disabled
Open System
Disabled
Disabled
--- v
---
---
--- v
---
---
--- v
---
---
---
Ad-hoc Infrastructure
Items Need to Be Checked
--- v v v v v v v v v v v
--v v v v
Chapter 4 Configuration 67
Wi-Fi Menu > Information
Information of network configuration can be viewed here.
Wi-Fi Menu > 1. Information
Ver Firmware version of the module chipset
MAC
IP
MAC ID of the 802.11b/g module
ID A name given to the mobile computer for identification.
By default, it is made up of model No. and the serial number. (Identical to 3.
WLAN Setting > 1. Local Name)
DHCP DHCP server in use or not
IP address of the mobile computer
Mask
Gate
Subnet Mask
Default Gateway
68 8500 Series Series Reference Manual
Wi-Fi Menu > Network Setting
Set parameters for IP networking.
Wi-Fi Menu > 2. Network Setting
1. DHCP Options - Enable or Disable
2. SubNet Mask
3. Local IP
4. Gateway
Enter a new Mask IP, if necessary.
Enter a new address for the mobile computer, if necessary.
Enter a new address for the default Gateway, if necessary.
5. DNS Server
6. Domain Name
Enter a new address for the DNS server, if necessary.
The domain name of the host is shown here when DHCP server is enabled.
Note: Normally, DHCP is enabled and all of the settings can be obtained form the DHCP server.
Chapter 4 Configuration 69
Wi-Fi Menu > WLAN Setting
Wireless networking can operate in two modes – (1) Ad-hoc mode: peer-to-peer, and (2)
Infrastructure mode: point to multi-point through access points.
Set the following parameters.
Wi-Fi Menu > 3. WLAN Setting
1. Local Name Enter a name for identifying the mobile computer.
By default, it is made up of model No. and the serial number.
2. SS ID
3. System Scale
This refers to Service Set ID or Identifier.
The mobile computer can ONLY communicate with access points that have the same SS ID.
This refers to Access Point Density.
4. Power Saving
5. Preamble
6. Ad-Hoc
Options - [1] Low [2] Medium [3] High
The value you set must match that set for the access point.
“Low / Medium / High” means the mobile computer will search for other APs only when data transmission rate is below “1 / 2 / 5” Mbps individually.
This refers to the low power consumption mode.
Options - Enable or Disable
The value you set must match that set for the access point.
Options - [1] Long [2] Short [3] Both
The value you set must match that set for the access point.
This refers to peer-to-peer mode, without going through access points.
Options - Enable or Disable
70 8500 Series Series Reference Manual
Wi-Fi Menu > Security
Set or modify security parameters.
WEP:
EAP:
Wired Equivalent Privacy
Extensible Authentication Protocol
Wi-Fi Menu > 4. Security
1. Authentication [1] Open System:
2. WEP Menu
Default authentication type
[0] Share Key: This requires implementing WEP key.
1. WEP Setting: Enabled (For Share Key, it must be enabled!)
Disabled (default)
2. WEP Key Length: 64 bits
128 bits (default)
3. Default Key: WEP KEY1
4. WEP Key:
3. EAP Menu
4. WPA Menu
1. EAP Setting:
2. EAP ID:
3. EAP Password:
1. WPA Setting:
2. WPA Passphrase:
Enter WEP Keys 1 ~ 4 in one of the following input data type:
ASCII (up to 13 characters)
Hexadecimal (up to 26 characters)
Enabled
Disabled (default)
Enter a user name (up to 32 characters)
Enter a password (up to 32 characters)
Enabled
Disabled (default)
Enter a phrase as your password (8 ~ 63 characters)
Chapter 4 Configuration 71
Wi-Fi Menu > Echo Tests
This function is used to measure the coverage of the range, estimate the number of APs and mobile computers needed, and determine the topology of deploying APs.
Wi-Fi Menu > 5. Echo Tests
1. Client Mode Set the mobile computer as a client. Enter the IP address of a server with which a connection is desired. Then, it will try to connect to an AP.
1. Run the Echo Test program on your computer. Associated settings include
- Select “TCP/IP – Server” for interface.
2. Server Mode
- Set Action Mode to “Passive”.
2. Start the echo test on both ends.
3. Enter the server IP and port number on the mobile computer.
Set the mobile computer as a server. The mobile computer will try to connect to an AP.
1. Run the Echo Test program on your computer. Associated settings include
- Select “TCP/IP – Client” for interface.
- Set Action Mode to “Passive”.
2. Start the echo test on both ends.
Note: Run the utility “Echo Test” on your computer (TCP/IP – Server or Client), and then, start this test on your mobile computer.
If WPA setting is enabled for security, the SSID and Passphrase will be processed to generate a pre-share key.
Note: If you change the SSID or Passphrase, it will have to re-generate a pre-share key.
1. For initial association with an access point, you will see an antenna icon developing on the screen to indicate that the mobile computer is processing a pre-share key.
72 8500 Series Series Reference Manual
2. After having generated the pre-share key, the mobile computer proceeds to establish a connection with an access point, and you will see the whole antenna is flashing.
3. When the mobile computer has been connected to the access point successfully, you will see the whole antenna and the indication of wireless signal strength.
Note: If you are programming in C or BASIC, be aware that these icons will appear on the device screen after NetInit() or START TCPIP() is called. (WPA must be enabled first!)
Chapter 4 Configuration 73
Once the connection of echo test is established, the details will be displayed as illustrated below. Link Quality (“Q”) will be the most important element while the others are for your reference.
Q (Link Quality)
0 ~ 10 Very Poor
10 ~ 15 Poor
15 ~ 30
50 ~ 80
Good
Very Good
12
18
24
36
48
54
T (Transmit Speed)
1 Mbps
2 Mbps
5.5
11
6
9
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
S (Signal Level)
0 ~ 10 Weak
30 ~ 60 Moderate
Over 60 Strong
N (Noise Level)
1 Weak
2 ~ 3 Moderate
4 ~ 5 Strong
74 8500 Series Series Reference Manual
4.1.8(4) GSM/GPRS Menu
This submenu is for GSM/GPRS networking. You must configure these parameters correctly.
The required information must be obtained from your GSM/GPRS network operator.
GSM:
Data services of GSM, including SMS (Short Message Service) and data call, are provided for receiving and sending data.
GPRS:
Through Access Points of GPRS, the mobile computer can establish a connection with the content server that connects to the Internet. Only client-initiated connection is supported.
Note: This submenu is generated only when the GSM/GPRS card is present.
GSM/GPRS Menu > Information
GSM / GPRS Menu > 1. Information
PIN Personal Identity Number of SIM card for security check. Undefined.
APN Access Point Name of your GPRS operator. Undefined.
GSM/GPRS Menu > Security
Chapter 4 Configuration 75
GSM / GPRS Menu > 2. Security
Enter PIN code of SIM card.
GSM/GPRS Menu > GPRS Setting
GSM / GPRS Menu > 3. GPRS Setting
1. AP Name Enter the AP name of your GPRS operator.
76 8500 Series Series Reference Manual
GSM/GPRS Menu > GSM/GPRS Tests
GSM / GPRS Menu > 4. GSM / GPRS Tests
1. GSM SMS Test This GSM Sending Test is used to verify connectivity for Short Message
Service. Enter a receiver telephone number on the mobile computer.
2. GSM Modem Echo The mobile computer will try to connect to a GSM modem.
1. Run the Echo Test program on your computer. Associated settings include
- Select “Modem” for interface.
- Set Action Mode to “Passive”.
2. Start the echo test on both ends.
3. Enter a receiver telephone number on the mobile computer.
4. The mobile computer will connect to the GSM modem that dials up your computer.
3. GPRS Client Mode The mobile computer will try to connect to your GPRS service provider.
1. Run the Echo Test program on your computer. Associated settings include
- Select “TCP/IP – Server” for interface.
- Set Action Mode to “Passive”.
2. Start the echo test on both ends.
3. Enter the server IP on the mobile computer.
4. The mobile computer will dials up to a GPRS AP, and finally connect to your computer (server) through the GPRS AP.
Note: Run the utility “Echo Test” on your computer (TCP/IP – Server or Client) or
“TcpServer.exe” for GPRS Client Mode. Then, start this test on your mobile computer.
Chapter 4 Configuration 77
4.2 Program Manager
The 8500 Series supports multiple applications and languages. In the menu of Program
Manager , it can download up to seven programs and one of them is made active.
If there is no application program exists, the Program Manager will be displayed after you turn on the mobile computer.
Warning! The Program Manager menu is NOT for the use of any end users.
How to access the Program Manager menu?
1. Turn off the mobile computer.
2. Press [8] + [Power].
78 8500 Series Series Reference Manual
4.2.1 Download
Here provides a full list of programs that are currently stored on the mobile computer with size information. Multiple application programs can be downloaded through a variety of interfaces. Upon completion of downloading, you are allowed to input a name for the program. If there is no need to rename the program, simply press [ENTER] to leave as it is.
The length of program name can be up to 12 characters. Program size is in kilo bytes.
A suffix letter after the memory sector (1 ~ 6) indicates the file type of program.
“b” for BASIC program (.SYN)
“c” for C program (.SHX)
“f” for font file (.SHX)
Note: In addition to the system font, there can be only one font file downloaded to the mobile computer. The custom font file needs to be downloaded through the System
Menu or Kernel Menu.
Chapter 4 Configuration 79
Spare Memory Sectors (1 ~ 6)
Additional program files can be directly downloaded to these sectors.
Download a program file to an empty sector:
1. Select an empty sector by pressing the corresponding number and then [Enter].
2. Select a desired baud rate for downloading.
3. Connect the RS-232 cable and wait for a few seconds to establish a connection…
4. To abort the action, press [ESC]. Then press [ESC] again to return to the menu.
Download a program file to an occupied sector:
If no available sectors, you'll have to replace one program with the new one.
1. Select a program that you want to delete by pressing the corresponding number and then [Enter].
2. The program information is displayed on the screen. Press [Alpha] to enter the Alpha mode, and then press [C].
3. Select a desired baud rate for downloading.
4. Connect the RS-232 cable and wait for a few seconds to establish a connection…
5. To abort the action, press [ESC]. Then press [ESC] again to return to the menu. From the menu, you'll find the program is deleted but no new program is present.
If you simply want to delete a program, press [D] in step 2.
Note: [C], [D] are NOT case-sensitive.
Active Memory Sector (“ACT”)
Only the application program, which needs to be activated immediately, can be downloaded to the active memory sector.
Download to Memory Sector “ACT”:
1. Press the [Down] key to select the memory sector “ACT” (may be unoccupied), and then press [Enter].
2. Connect the RS-232 cable and wait for a few seconds to establish a connection…
3. If the active memory sector has already been occupied by an application program, the newly downloaded program will replace the currently active program and come into effect immediately.
80 8500 Series Series Reference Manual
4.2.2 Activate
The list shows the entire spare programs stored on the mobile computer. From the list, you can select from 1 to 6 and activate one of them. The selected program will be copied to the active memory sector and replace the current one.
Note: A font file cannot be activated.
To Clear File System
When <New Program Start> screen prompts “Press [ESC] to clear file”, it means the file system in the SRAM will be cleared out by pressing [ESC]. Then there will be no data
(transactions, settings, etc.) stored on the mobile computer when the new program comes into effect.
To Keep File System
To keep the data, simply press any other key.
Chapter 4 Configuration 81
4.2.3 Upload
You may duplicate one or all of the programs from the mobile computer to a host computer or another mobile computer. This can be used to clone software on mobile computers.
Note: To clone all of the programs, the target mobile computer cannot have any other program downloaded except the active one; that is, Memory Sectors 1~6 must be empty!
The procedures are similar to those for downloading programs.
82 8500 Series Series Reference Manual
4.3 Kernel Menu
The kernel resides in the innermost core of the system. It has the highest security and is always protected by the system. When the application program is corrupted and the System
Menu fails, the Kernel Menu provides an access to fix the system.
Warning! The Kernel Menu is NOT for the use of any end users.
How to access the Kernel Menu?
1. When the last session is in the System Menu or Program Manager , simply turn off the mobile computer. Otherwise, you must reload the battery pack.
2. Press [1] + [7] + [Power].
Chapter 4 Configuration
4.3.1 Kernel Information
Here provides important system information to help diagnose the system.
83
H/W:
S/N:
Hardware version (PCB)
Serial number of the mobile computer
M/D: Manufacturing
KNL: Kernel version
DEV: 5-digit code for optional hardware configurations
For example, 1710-1 indicates the 44-key mobile computer is equipped with CCD scan engine, RFID reader, and 802.11b/g and
GSM/GPRS connectivity.
Refer to Understanding Device Code
.
84 8500 Series Series Reference Manual
4.3.2 Load Program
You can download one program file to the active memory sector, as well as one font file to the memory address assigned by the system. After downloading, restart the mobile computer to activate the new program.
New application program or program update
And/or one font file, i.e. multi-language font
If you are using a custom font file rather the system font and you want to download another font file, it is necessary to delete the current font file from the program list displayed by the
first. Otherwise, downloading new font file is not allowed.
.SHX Program
Program File
Font File
Download one of the following C program files and/or one font file:
AG Runtime (U*.shx)
CipherNet Runtime (85xx-5250.shx, 85xx-VT.shx)
BASIC Runtime* (BC*.shx)
User program
Refer to the Font Files folder on CD-ROM.
If you have downloaded a BASIC Runtime program, the next time you access the Load
service through the System Menu , you will be able to select whether to download a
C program (.SHX) or BASIC program (.SYN).
Note: To download a BASIC program (*SYN), go to System Menu > 6. Load Program >
2. Load Basic.
Chapter 4 Configuration 85
Settings
Interface
Cradle-IR (Serial IR)
IrDA
Bluetooth
Proceed to configure baud rate settings on your computer and the mobile computer.
Point to the target IrDA device.
Approach the target Bluetooth enabled device.
Baud Rate
115200 (bps)
76800 (bps)
57600 (bps)
38400 (bps)
19200 (bps)
9600 (bps)
4800 (bps)
2400 (bps)
Supported on CipherLab software, including download utilities.
N/A
Supported on CipherLab software, including download utilities.
Supported on CipherLab software, including download utilities.
Supported on CipherLab software, including download utilities.
Supported on CipherLab software, including download utilities.
N/A
N/A
Note: If you select to use Serial IR of the Modem Cradle, any value other than 57600 bps
(default) must be configured through the DIP switch on the IR control board.
Load Program via Bluetooth
1. Go to System Menu > 7. Bluetooth Menu > 3. Security , and configure the following
Bluetooth settings first.
Authentication
PIN code
2. Go to System Menu > 6. Load Program and select Bluetooth.
3. Start the pairing procedure from your computer, for example, click [Pair Device] and/or
[Connect Bluetooth Serial Port].
4. Run any of the download utilities: ProgLoad.exe or Download.exe
- Select interface RS-232/IrDA for using Bluetooth SPP.
- Select COM port properties that match with the serial port settings used on your computer.
86 8500 Series Series Reference Manual
4.3.3 Kernel Update
The kernel might need to be updated to improve performance or due to other considerations.
To download a kernel update (K*.shx), the procedure is the same as that for downloading a program.
Any attempt to download an older version will be rejected.
The system will restart itself right after downloading.
Warning: Do not turn off the mobile computer while downloading a kernel update or re-starting the mobile computer. Otherwise, it will crash the kernel forever.
There is no way to recover it!
Note: CipherLab software, including download utilities, supports the following baud rate options: 115200/57600/38400/19200/9600 bps.
4.3.4 Test & Calibrate
These tools are provided for manufacturing use.
Chapter 4 Configuration 87
1. Burn-In Test
2. Calibrate RTC
3. Base RAM Test
4. Memory Card Test
5. Scanner Test
6. Bluetooth Test
7. PCMCIA Test
8. LCD Test
Warning! You should not perform any of these tests.
88 8500 Series Series Reference Manual
4.3.5 Bluetooth Menu
This submenu is the same as the one under the System Menu except for the following items:
"2. Connect Set > 5. BT-GPRS AP Name" is not provided.
"4. Echo Tests" is provided with SPP options only.
"7. Network Setting" is not provided.
Specifications
89
Model Designation
Wireless
Communications
IR/IrDA
8500
√
Bluetooth Class 2 √
802.11b/g –
GSM/GPRS –
Electrical
Characteristics
Physical
Characteristics
Memory
8570
√
√
√
8580
√
√
–
– √
Main Battery Rechargeable Li-ion battery – 3.7 V, 4000 mAh
Working Time Laser, one scan per 5 seconds, with backlight on –
400 hours in batch mode
32 hours in Wi-Fi mode
Backup Battery Rechargeable Lithium button cell – 3.0 V, 7 mAh
Data retention – at least 7 days
CPU 32-bit Toshiba CMOS type, 40 MHz
Display
Keypad
Indicators
Vibrator
8590
√
√
√
√
Program memory – 2 MB flash
Data memory – 2 MB SRAM, upgradeable
Graphic LCD, 160 x 160 pixels, 3” FSTN with LED backlight programmable
Font size 6x8: 26 characters by 19 lines
Font size 8x16: 20 characters by 9 lines
Also a touch screen allows for the use of stylus for control and signature capture.
24 or 44 rubber keys, LED backlight programmable
LED – Dual-color (red/green), programmable
Buzzer – Low power transducer type, 1 KHz to 4 KHz, programmable
9000 ± 2000 RPM, Max. 50 dB, programmable
Enclosure
Material
Rubber & ABS plastic
Readers
Dimensions 230 mm (L) 91 mm (W) 65 mm (H)
Weight Approx. 600 g (Laser and battery included)
Barcode Reader CCD (linear imager)
Standard Laser
Long Range Laser
Extra Long Range Laser
2D Imager
90 8500 Series Series Reference Manual
Environmental
Characteristics
Programming
Accessories
RFID Reader
Operating
Temperature
Storage
Temperature
Operating
Humidity
Frequency 13.56 MHz
-20 °C to 60 °C
-30 °C to 70 °C
-10 °C to 60 °C
10% to 90% non-condensing
Storage Humidity 5% to 95% non-condensing
Impact
Resistance
1.5 m, 5 drops per 6 sides
IP 64 Splash / Dust
Resistance
Electrostatic
Discharge
± 15 kV air discharge, ± 8 kV direct discharge
EMC Regulations FCC, CE, C-Tick, DGT, BSMI, TELEC, MIC, RSS-210
Development
Tools
C and BASIC
Software &
Utilities
Windows-based Application Generator (AG), AG utilities;
Windows-based CipherNet for VT100/220, IBM 5250 emulation;
Download utilities, testing tools, etc.
4 or 8 MB Memory Card
Pistol Grip
Belt Holster
Protective Cover
Spare rechargeable battery pack
4-slot Battery Charger
Charging & Communication Cradle
Modem Cradle (56 K)
Ethernet Cradle (10/100 BASE-T)
Vehicle Cradle
Bluetooth Access Point
802.11b/g Access Point
Troubleshooting
91
The mobile computer cannot be turned on when you press the POWER key…
Make sure the battery pack is installed properly.
Re-charge the battery inside the mobile computer and monitor the charging status. (see 4.1.5)
If the battery is faulty, replace it with a fresh and fully charged battery then.
Charging error…
Make sure the power cord is well connected between the cradle/charger and an outlet.
Check if the battery contacts of the battery itself and the battery compartment are clean.
Try to re-charge the battery and monitor the charging status.
Warning! Only use batteries or charging device manufactured by CipherLab. The use of wrong battery or charging device could result in damage to human body or the product itself, and will void your warranty.
The keyboard input seems not working properly…
Perform the keyboard test. (see 4.1.3)
If the problem persists, slide the battery latch to reload the battery pack. Then perform the test again.
The reader does not scan…
Low battery -
Check if the battery icon on the screen indicates a low battery status. If so, replace it with a fresh battery then.
If the problem persists, check if the battery contacts get dirty or the battery pack does not fit to the compartment.
Regarding the reader -
Perform the reader test to see if the reader is working. (see 4.1.3)
If the problem persists, slide the battery latch to reload the battery pack. Then perform the test again.
92 8500 Series Series Reference Manual
The reader does not decode after scanning…
Unreadable barcode -
Check if the barcode is defaced. A defaced barcode may not be readable.
Un-programmed to read -
Check if the scanner is programmed to read the symbologies (types of barcode) that you are trying to read.
Try scanning a test barcode of the symbology you are trying to read.
Dirty scan window-
Check if the scan window gets dirty. Wipe it with a clean and dry cloth, and try again.
Out of scanning range -
Try adjusting the scanning distance from the scanner to the barcode.
The mobile computer cannot transmit/receive data to/from a host computer or other devices…
Over IR port -
Make sure the mobile computer's infrared port is pointed directly to the infrared port of another
IR device. The distance between the mobile computer and a target device is within proper range, and no obstacles in between. Try to establish connection again.
Via Bluetooth -
Make sure the distance between the mobile computer and a target device is within proper range. Try to establish connection again.
Check if the relevant settings are correct. (see 4.1.7)
Check if the connection is working properly. (see 4.1.7)
Over RS-232 port via cradle -
Check if the RS-232 connection is correct and secured.
Make sure the serial port parameters on the host are configured to match the serial parameters on the mobile computer. Try to establish connection again.
Make sure the mobile computer is well seated inside the cradle. DO NOT remove the mobile computer or disconnect the cradle before communications are done.
If the problem persists, run the IR Echo Test to check the IR interface between the mobile computer and the cradle. (see 4.1.3)
Troubleshooting 93
Over MODEM port via cradle -
Check if the modem connection is correct and secured.
Make sure the modem parameters are configured to match the parameters on the mobile computer. Try to establish connection again.
Make sure the mobile computer is well seated inside the cradle. DO NOT remove the mobile computer or disconnect the cradle before communications are done.
If the problem persists, run the IR Echo Test to check the IR interface between the mobile computer and the cradle. (see 4.1.3)
About abnormal response…
The LED or LCD seems not working properly -
Perform the LCD & LED test. (see 4.1.3)
If the problem persists, reload the battery pack and perform the test again.
The buzzer seems not working properly -
Perform the buzzer test. (see 4.1.3)
If the problem persists, reload the battery pack and perform the test again.
The mobile computer seems not working properly -
First upload all data to a computer, and then perform the memory test. (see 4.1.3)
If the problem persists, reload the battery pack and perform the test again.
The touch screen seems not working properly -
Perform the touch screen test. (see 4.1.3)
If the problem persists, reload the battery pack and perform the test again.
The vibrator seems not working properly -
Perform the vibrator test. (see 4.1.3)
If the problem persists, reload the battery pack and perform the test again.
94 8500 Series Series Reference Manual
A P P E N D I X I
Download Utilities
95
The utilities are provided for you to download a program (*.SHX or *.SYN) to the mobile computer. Programs can be as follows:
Program Type
AG Runtime U*.SHX
CipherNet
Runtime
85xx-VT.SHX
85xx-5250.SHX
BASIC Runtime BC*.SHX
BASIC program *.SYN
Font file e.g.
Font-Multi-Language.SHX
Kernel update K*.SHX
√
√
√
System Menu Kernel Menu Program Manager
√ √ √
√ √ √
−
√
−
√
√
√
−
−
−
Currently, the program ProgLoad.exe has replaced several previously released utilities as shown below.
Download.exe
IRLoad.exe
SynLoad.exe
: to download a *.SHX file
: to download a *.SHX file
: to download a *.SYN file
96 8500 Series Series Reference Manual
ProgLoad.exe
This all-in-one utility supports all the file types and communications interfaces. Run the program on your computer. The following dialog box pops up.
Click to select Comm type, COM port, and
Baud rate.
Choose your file…
Communication Type
RS-232 / IrDA: Connection via direct RS-232 cable, IrDA port, or Bluetooth SPP
Download.exe)
Serial IR:
TCP/IP:
Connection via cradle (= IRLoad.exe)
Connection via networks (Not applicable!)
File Type
*.SHX:
*.SYN:
Any C program, such as AG Runtime, Basic Runtime, font file, etc
Any Basic program after Basic Runtime has been installed first
Appendix I Download Utilities 97
IRLoad.exe
This utility is provided when you establish a connection via the cradle.
1. Run the program on your computer.
2. Choose a .SHX file.
3. Select COM port properties.
Command Line
It also supports command line arguments. For example,
IRLOAD U8300-114.SHX,2,1//COM2,115200 bps
If command line arguments are not given, the user can select appropriate parameters from the pop-up dialog box.
IRLOAD [filename],[COM port],[Baud rate]
File name: The file name of the program that is to be downloaded.
COM port:
Baud rate:
1 ~ 8
1 ~ 5 1 for 115200 bps
2 for 57600 bps
3 for 38400 bps
4 for 19200 bps
5 for 9600 bps
Default: 1
Default: 1
98 8500 Series Series Reference Manual
Download.exe
This utility is provided when you establish a connection via serial interface, such as a direct
RS-232 cable, IrDA port, or Bluetooth SPP.
1. Run the program.
2. Choose a .SHX file.
3. Select COM port properties.
Command Line
It also supports command line arguments.

Public link updated
The public link to your chat has been updated.
Advertisement