Advertisement
Advertisement
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Country
EIRE
U.K
Customer Care Centre
0818 717100
0330 SAMSUNG (7267864)
Web Site www.samsung.com
www.samsung.com
LED TV user manual
© 2013 Samsung Electronics Co., Ltd. All rights reserved.
[UF6320-XU]BN68-04881B-02ENG.indb 1
BN68-04881B-02
Thank you for purchasing this Samsung product.
To receive more complete service, please register your product at www.samsung.com/register
Model _____________ Serial No. _____________
2013-11-14 5:04:23
Important Safety Instructions
Warning! Important Safety Instructions
(Please read the appropriate section that corresponds to the marking on your Samsung product before attempting to install the product.)
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.
This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
• The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of this apparatus, and to protect it from overheating, these slots and openings must never be blocked or covered.
− Do not cover this apparatus in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided.
− Do not place this apparatus near or over a radiator or heat resistor, or where it is exposed to direct sunlight.
− Do not place a water containing vessel(vases etc.) on this apparatus, as this can result in a risk of fire or electric shock.
• Do not expose this apparatus to rain or place it near water(near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool etc.). If this apparatus accidentally gets wet, unplug it and contact an authorized dealer immediately. Make sure to pull out the power cord from the outlet before cleaning.
• This apparatus use batteries. In your community there might be regulations that require you to dispose of these batteries properly under environmental considerations. Please contact your local authorities for disposal or recycling information.
• Do not overload wall outlets, extension cords or adaptors beyond their capacity, since this can result in fire or electric shock.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plug end, adaptors and the point where they exit from the appliance.
• To protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor corresponds to the local electrical supply.
• Never insert anything metallic into the open parts of this apparatus. Doing so many create a danger of electric shock.
• To avoid electric shock, never touch the inside of this apparatus. Only a qualified technician should open this apparatus.
• Make sure to plug the power cord in until it is firmly inserted. When removing the power cord, make sure to hold the power plug when pulling the plug from the outlet. Do not touch the power cord with wet hands.
• If this apparatus does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service centre.
• Be sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an extended period of time (especially when children, elderly or disabled people will be left alone in the house).
− Accumulated dust can cause an electric shock, an electric leakage or a fire by causing the power cord to generate sparks and heat or the insulation to deteriorate.
• Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substances and where it operates for 24 hours such as the aerial port, the train station etc.
• Failure to do so may cause serious damage to your set.
• Use only a properly grounded plug and receptacle.
− An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.
• Do not allow children to hang onto the product.
• Store the accessories (battery, etc.) in a location safely out of the reach of children.
• Do not install the product in an unstable location such as a shaky self, a slanted floor or a location exposed to vibration.
• Do not drop or impart any shock to the product. If the product is damaged, disconnect the power cord and contact a service centre.
• Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, aerial freshener, lubricant or detergent. This may damage the appearance or erase the printing on the product.
• Apparatus shall not be exposed to dripping or splashing.
• Do not dispose of batteries in a fire.
• Do not short circuit, disassemble or overheat the batteries.
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• WARNING - TO PREVENT THE SPRE AD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.
English - 2
[UF6320-XU]BN68-04881B-02ENG.indb 2 2013-11-14 5:04:23
Contents
Basic Features
7 Installing batteries (Battery size: AAA)
Switching Between Video Sources
Universal Remote Control Setup
Connecting to a COMMON INTERFACE slot (Your TV viewing Card Slot)
12 Using the Icons at the Top of the Page
Network Configuration
13 Network Connection - Wireless
13 Wireless Network Precautions
3D Basics
Troubleshooting and Other
Information
Mounting the TV on the Wall Using the Wall Mount Kit (Optional)
Providing Proper Ventilation for Your TV
Eco Sensor and Screen Brightness
Tip Prevention – Securing the TV to the Wall
Specifications
Guides
English - 3
[UF6320-XU]BN68-04881B-02ENG.indb 3 2013-11-14 5:04:23
Basic Features
Figures and illustrations in this User Manual are provided for reference only and may differ from the actual product appearance. Product design and specifications may change without notice.
CIS languages (Russian, Ukrainian, Kazakhs) are not available for this product, since this is manufactured for customers in EU region.
Features for your new TV
• 3D : This new feature enables you to view 3D content.
• SMART HUB :
This TV features Smart Hub, a multi-purpose entertainment and family centre. With Smart Hub, users can surf the web, download applications, and stay in touch with family and friends through social networking services. In addition, you can enjoy photo, video, and music files stored on external storage devices.
™ Press to launch Smart Hub. Choose a service using the icons displayed in the top part of the screen.
Social : Watch the latest YouTube videos and you and your friends' video posts on Facebook and
Twitter. You can also make video calls to friends by connecting the TV to a camera (sold separately).
Apps : Download and install applications such as WebBrowser.
On TV : On TV recommends TV programmes based on their popularity or your personal preferences.
(Depending on the country)
Films and TV Shows : Purchase and watch movies and series without a separate external device.
(Depending on the country)
Photos, Videos & Music : Play back photo, video, and music files from an external storage device.
• Anynet+ (HDMI-CEC) : This allows you to control all connected Samsung devices that support
Anynet+ with your Samsung TV’s remote.
• e-Manual : Provides a detailed, on-screen user's manual built into your TV. (page 12)
• Device Manager : Use the TV features with a USB keyboard and mouse.
• Screen Mirroring : Displays mobile device screens on your TV wirelessly.
✎ WARNINGS : Image retention, commonly known as screen burn-in, can occur on most types of television if the same image is displayed continuously. The most common causes of image retention are logos that remain stationary on the TV screen. These logos are common on many programmes received via a Set-top Box. To reduce this risk, avoid displaying still images for long durations and lower the brightness or contrast settings to decrease the intensity of the picture. Extended viewing of movies and programs in aspect ratios that are different from the aspect ratio of the TV may cause image retention. Always endeavour to avoid black borders top or bottom by using the zoom function.
This will help eliminate the black borders and fit the picture to the entire area of the screen. Using a video game console may cause image retention and is not recommended. When using a PC input, avoid displaying still images for long durations and reduce the brightness or contrast settings to decrease the intensity of the picture.
✎ IMPORTANT : Image retention issues are not covered by your Samsung® warranty.
English - 4
[UF6320-XU]BN68-04881B-02ENG.indb 4 2013-11-14 5:04:24
Accessories
✎ Please make sure the following items are included with your TV. If any items are missing, contact your dealer.
✎ The items’ colours and shapes may vary depending on the models.
✎ Cables not included in the package contents can be purchased separately.
✎ Check that there is no accessory hidden behind packing materials when you open the box.
• Remote Control & Batteries (AAA x 2)
• User Manual
• Samsung 3D Active Glasses
• Power Cord
• Regulatory Guide
Cable manager
Holder-Ring
(Depending on the Model)
CI Card Adapter IR Extension Cable
• An administration fee may be charged if either
− (a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual)
− (b) you bring the unit to a repair centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
• The amount of such administration charge will be advised to you before any work or home visit is carried out.
Warning: Screens can be damaged from direct pressure when handled incorrectly. We recommend lifting the
TV by the edges, as shown.
Don't Touch
This Screen!
[UF6320-XU]BN68-04881B-02ENG.indb 5
English - 5
2013-11-14 5:04:24
Using the Remote Control
Learn where the function buttons are on your remote. Especially note these: SOURCE , MUTE , Y ,
< P > , MENU , TOOLS , E , INFO , CH LIST , RETURN , GUIDE and EXIT .
✎ This remote control has Braille points on the Power , Channel , and Volume buttons and can be used by visually impaired persons.
Turns the TV on and off.
Gives direct access to channels.
Alternately select Teletext ON Double, Mix or OFF.
Adjusts the volume.
Displays channel lists on the screen.
Opens the OSD (Menu).
Quickly selects frequently used functions.
Moves the cursor, selects the on-screen menu items, and changes the values seen on the TV's menu.
Returns to the previous menu.
Use these buttons according to the directions on the TV's screen.
Use these buttons in a specific feature.
Use these buttons according to the directions on the TV's screen.
[UF6320-XU]BN68-04881B-02ENG.indb 6
Turn on and off the satellite or cable set-top box connected to the TV.
Displays and selects the available video sources.
English - 6
Returns to the previous channel.
Cuts off the sound temporarily.
Changes channels.
Brings up Smart Hub applications. See the e-Manual chapter, SMART TV Features >
Smart Hub .
Displays the EPG (Electronic Programme
Guide).
Displays information on the TV screen.
Exits the menu.
SEARCH: Support to recommendation search word and search function. See the e-Manual chapter, SMART TV Features > Smart Hub >
Searching .
STATUS : Display the status and notification banner at the top of the screen.
MORE : Displays a virtual remote control on the screen. See the e-Manual chapter, Controlling
TV > Using the Virtual Remote Control.
E-MANUAL : Displays the e-Manual.
RECOMMEND : Displays the recommended programmes from among the programmes currently being broadcast as well as recommended applications are listed.
AD/SUBT.
: Turns the audio description on and off (not available in some locations). / Displays digital subtitles. See e-Manual chapter TV
Viewing > Subtitles .
2013-11-14 5:04:25
Installing batteries (Battery size: AAA)
Match the polarity of the batteries to the symbols in the battery compartment.
✎ NOTE
− Use the remote control within 23 feet of the TV.
− Bright light may affect the performance of the remote control. Avoid using when near special fluorescent lights or neon signs.
− The colour and shape may vary depending on the model.
Turning on the TV
Turn on the TV using the P button on the remote control or TV panel.
✎ The product Colour and shape may vary depending on the model.
✎ The TV’s Controller, a small joy stick like button on the rear right side of the TV, lets you control the TV without the remote control.
Function menu m R
P
TV Controller
On-screen display shown when using TV
Controller.
Remote control sensor
[UF6320-XU]BN68-04881B-02ENG.indb 7
English - 7
2013-11-14 5:04:25
SETUP
The initial setup dialog appears when the TV is first activated. Follow the on-screen instructions to finish the initial setup process, including menu language choice, channel scan, network connection, and more. At each step, either make a choice or skip the step. Users can manually perform this process at a later time under the Screen Menu > System > Setup menu.
✎ If you connect any device to HDMI1 before starting the installation, the Channel Source will be changed to Settop box automatically.
✎ If you do not want to select Set-top box , please select Aerial .
Samsung ‘On TV’ Recommendations Service
The On TV service recommends TV programmes based on their popularity or your personal preferences.
To enjoy the On TV service, please follow the steps below. (You must have an Internet connection.)
1. Configure your TV : Select TV source to be used for On TV .
Aerial : Freeview, Freesat, DVB-T/C/S
Set-top box : External Cable Box, External Satellite Box
2. Auto tuning channels : This step only occurs if ‘Aerial’ was selected in step 1.
3. Select a Service Provider : To select your preferred programme provider for On TV, enter your postcode and select your Freeview, Freesat or external satellite television provider from the displayed list.
4. Set-top Box Control Test : This test is for checking that your TV remote can control your Set-top Box.
This step only occurs if ‘Set-top box’ was selected in step 1.
[UF6320-XU]BN68-04881B-02ENG.indb 8
English - 8
2013-11-14 5:04:25
Switching Between Video Sources
Press SOURCE button to switch between devices connected to the TV.
For example, to switch to a game console connected to the second HDMI connector, press SOURCE button. From the Source list, select HDMI2 . The connector names may vary depending on the product.
Select Tools button at the upper-right corner of the screen to access the following functions.
✎ For some compatible devices connected via SCART or HDMI sockets, the TV may automatically select the correct source when this device is accessed. For this to work the HDMI Anynet+ system must be switched on (see Screen Menu > System > Anynet+ (HDMI-CEC) ). Anynet+ will also automatically power off compatible HDMI devices when the TV is switched off.
• Information
View detailed information about the connected devices.
• Edit Name
You can rename devices connected to the TV to more easily identify external sources.
With a computer connected to the TV's HDMI (DVI) port via an HDMI cable, for example, you can change Edit Name to PC .
With a computer connected to the TV's HDMI (DVI) port via an HDMI-to-DVI cable, for example, you can change Edit Name to DVI PC .
With an AV device connected to the TV's HDMI (DVI) port via an HDMI-to-DVI cable, for example, you can change Edit Name to DVI Devices .
• Anynet+ (HDMI-CEC)
A list appears showing Anynet+ compatible ones of external devices connected to the TV.
✎ This function is only available Anynet+ (HDMI-CEC) function set to On .
• Disconnect USB Device
Remove the USB device from the list safely. This function is only available when the USB device selected.
✎ For some compatible devices connected via SCART or HDMI sockets, the TV may automatically select the correct source when this device is accessed. For this to work the HDMI Anynet+ system must be switched on (see Menu , Settings …..). Anynet+ will also automatically power off compatible HDMI devices when the TV is switched off.
• Universal remote setup
To add a new external device to control it with the Remote Control, press the SOURCE button and select Universal remote setup on the top right of the screen. Using the universal remote control, users can control external devices connected to the TV, such as a settop box, Blu-ray player, and AV receiver.
[UF6320-XU]BN68-04881B-02ENG.indb 9
English - 9
2013-11-14 5:04:25
Universal Remote Control Setup
This TV has a universal remote control feature that lets you control cable boxes, Blu-ray players, home theatres, and other third-party external devices connected to the TV using the TV's remote control.
✎ Some or new models of the external device connected to the TV, may not be supported the
Universal remote setup .
Keep a distance of 5 cm at least between the IR Extender and the external device, as the illustration shows. Face the IR Extender toward the external device’s remote control signal receiver. Note that it should be no obstacle between IR Extender and external device. The presence of an obstacle will interfere with the transmission of the remote control signal.
Add the External Device
1. Turn on the external device you wish to set up universal remote function for and then press SOURCE to bring up the Source screen.
2. Select Universal remote setup from the top of the screen. This initiates the universal remote setup process.
3. Follow the on-screen instruction and set up the universal remote control. If it does not work, set up the remote control by entering the model number manually.
[UF6320-XU]BN68-04881B-02ENG.indb 10
English - 10
2013-11-14 5:04:26
Connecting to a COMMON INTERFACE slot (Your TV viewing Card Slot)
✎ Turn the TV off to connect or disconnect a CI card or CI card adapter.
Attaching the CI Card Adapter
Attach the adapter as shown side.
✎ To install the CI CARD Adapter, please remove the sticker attached to the TV.
To connect the CI CARD Adapter, follow these steps.
✎ We recommend attaching the adapter before installing the wall mount, or inserting the “CI or CI+ CARD”.
TV Rear
1. Insert the CI CARD Adapter into the two holes on the product 1 .
✎ Please find two holes on the rear of the TV, beside the COMMON INTERFACE port.
2. Connect the CI CARD Adapter into the COMMON INTERFACE port on the product 2 .
3. Insert the “CI or CI+ CARD”.
We recommend that you attach the CI Card adapter and insert the CI card (viewing card) before you mount the TV on the wall because it may be difficult and hazardous do this when it is on the wall.
Using the “CI or CI+ CARD”
To watch paid channels, the “CI or CI+ CARD” must be inserted.
• If you don’t insert the “CI or CI+ CARD”, some channels will display the message “Scrambled Signal”.
• The pairing information containing a telephone number, the “CI or
CI+ CARD” ID the Host ID and other information will be displayed in about 2~3 minutes. If an error message is displayed, please contact your service provider.
• When the configuration of channel information has finished, the message “Updating Completed” is displayed, indicating the channel list is updated.
✎ NOTE
• You must obtain a “CI or CI+ CARD” from a local cable service provider.
• When removing the “CI or CI+ CARD”, carefully pull it out with your hands since dropping the “CI or CI+
CARD” may cause damage to it.
• Insert the “CI or CI+ CARD” in the direction marked on the card.
• The location of the COMMON INTERFACE slot may be different depending on the model.
• “CI or CI+ CARD” is not supported in some countries and regions; check with your authorized dealer.
• If you have any problems, please contact a service provider.
• Insert the “CI or CI+ CARD” that supports the current aerial settings. The screen will be distorted or will not be seen.
English - 11
[UF6320-XU]BN68-04881B-02ENG.indb 11 2013-11-14 5:04:27
Viewing the e-Manual
The embedded e-Manual contains information about your TV's key features.
This TV has a built-in user guide. To read it, use one of the following methods:
• Open the Support menu and choose e-Manual (Troubleshooting) .
• Press the E-MANUAL button on the standard remote control.
✎ Words in blue refer to screen menu options and words in light blue refer to remote control buttons.
✎ A printable version of this guide is also available at www.samsung.com/support.
Scrolling a Page
To scroll a page, use of one of the following methods:
• Press the or button on the scroll bar at the right edge of the screen.
• Place the cursor on the or button at the right edge of the screen, press the up or down arrow button on the remote.
Using the Icons at the Top of the Page
Use the Back , Forward , and Opened page icons on the top left of the screen to navigate through pages.
These icons are available when two or more pages are passed.
Returning to the Home Page
To return to the home page, press the a button or select on the top right of the screen.
Searching the Index
Press the { button or select on the top of the screen to access the search screen. Enter a search phrase and select Done . Select an item from the search results list to navigate to the relevant page.
Searching Pages
Press the { button or select on the top of the screen to access the search screen. Enter a search phrase and select Done . Select an item from the search results list to navigate to the relevant page.
Closing the e-Manual
To close the e-Manual, select at the upper-right corner of the screen or press EXIT button.
Jumping to a Menu Item
To directly jump to the menu item that is described in the current section, select . It is possible to jump from a menu item directly to the related section in the e-Manual. On the screen menu, press the
E-MANUAL button that appears on the screen.
✎ This feature may not be available, depending on the menu.
English - 12
[UF6320-XU]BN68-04881B-02ENG.indb 12 2013-11-14 5:04:27
Network Configuration
Updating the e-Manual
Open the Smart Hub and select Apps , and then select More Apps . The e-manual can be updated in the same way with an application update.
On the More Apps screen, select Apps to update . Select e-Manual from the list. The e-Manual starts updating to the latest version. However, Apps to update appears on the screen only when the update is required.
Connecting to a Network
Connecting the Smart TV to a network gives you access to online services such as the Smart Hub, as well as software updates.
Network Connection - Wireless
Connect the TV to the Internet using a standard router or modem.
The LAN Port on the Wall
Wireless IP Router or Modem that has a DHCP Server
LAN Cable (Not Supplied)
Wireless Network Precautions
• This Smart TV supports the IEEE 802.11a/b/g /n communication protocols. Samsung recommends using IEEE 802.11n. Otherwise when you play video over a network connection, the video may not play smoothly.
• To use a wireless network, the TV must be connected to a wireless router or modem. If the wireless router supports DHCP, the TV can use a DHCP or static IP address to connect to the wireless network.
• Select a channel that is not currently in use for the wireless router. If the channel set for the wireless router is currently being used by another device, the result is usually interference and/or a communications failure.
• Most wireless networks have an optional security system. To enable a wireless network's security system, you need to create a security key using characters and numbers. This security key is then needed to connect to the wireless network.
[UF6320-XU]BN68-04881B-02ENG.indb 13
English - 13
2013-11-14 5:04:28
Network Security Protocols
The TV only supports the following wireless network security protocols and is unable to connect to noncertified wireless routers:
• Authentication Modes: WEP, WPAPSK, WPA2PSK
• Encryption Types: WEP, TKIP, AES
If the wireless router has been set to Pure High-throughput (Greenfield) 802.11n mode and the Encryption
Type to WEP or TKIP, Samsung Smart TVs will not support the connection in compliance with the new Wi-
Fi certification specifications.
If the wireless router supports WPS (Wi-Fi Protected Setup), it is possible to connect to the network using
PBC (Push Button Configuration) or a PIN (Personal Identification Number). WPS automatically configures the SSID and WPA key settings.
Network Connection - Wired
There are three main ways to connect your TV to your network using cable, depending on your network setup. They are illustrated starting below:
TV Rear Panel
The Modem Port on the Wall External Modem
(ADSL / VDSL / Cable TV)
Modem Cable (Not Supplied)
The Modem Port on the Wall External Modem
(ADSL / VDSL / Cable TV)
LAN Cable (Not Supplied)
IP Router that has a
DHCP Server
TV Rear Panel
Modem Cable
(Not Supplied)
The LAN Port on the Wall
LAN Cable
(Not Supplied)
LAN Cable
(Not Supplied)
TV Rear Panel
LAN Cable (Not Supplied)
✎ The TV does not support network speeds less than or equal to 10Mbps.
✎ Use Cat 7 cable for the connection.
English - 14
[UF6320-XU]BN68-04881B-02ENG.indb 14 2013-11-14 5:04:28
3D Basics
3D Active Glasses
Features
Samsung's SSG-5100GB 3D glasses enable you to view 3D images on your 3D TV. The Samsung 3D glasses communicate with Samsung 3D TVs via the 2.4GHz RF band.
✎ The Samsung 3D glasses are only compatible with Samsung D, E, and F series 3D TV's that were released in 2011, 2012, and 2013. These 3D glasses cannot be connected to other Bluetooth devices.
Parts
LED Indicator & Power Button
Battery Cover
Liquid crystal shutter
For details on how to attach the glass temples and how to pair the glasses with the TV, refer to the separate 3D glasses manual.
Replacing the Battery
If the red LED blinks every two seconds continually, replace the battery with a new one.
✎ Insert the "+" side of the battery into the side marked with "+" in the battery compartment.
✎ To check the remaining battery capacity, refer to the pairing section in this manual.
Pull the battery cover downward
Open the battery cover Remove the battery Replace the battery Push the battery cover downward
Close the battery cover
Pairing 3D Active Glasses
✎ What is Pairing? Pairing is the process of connecting 3D glasses and a 3D TV so that the two devices can exchange data.
✎ Ensure your Samsung TV and 3D glasses are no farther than 19.5 in (50 cm) apart from each other while pairing is in progress.
[UF6320-XU]BN68-04881B-02ENG.indb 15
English - 15
2013-11-14 5:04:29
• Turning the glasses on
Press the power button briefly. The green LED is turned on for 3 seconds.
(Make sure that 3D is activated on the TV before using the 3D glasses.)
• Turning the glasses off
Press the power button briefly. The red LED is turned on for 3 seconds.
• Performing the pairing process
Turn the TV on and let it power up completely. Press and hold the Power button on the glasses. The green and the red LEDs blink alternately for 2 seconds.
• Operating range
Recommended pairing distance
2~6m
50cm
Recommended viewing distance
Recommended pairing distance
2~6m (6.5 to 19.5 ft)
50 cm or less (19.5 in)
Recommended viewing distance
✎ Once the 3D glasses are paired, the remaining battery capacity is displayed on the TV screen. (This feature only applies to Samsung F series 3D TVs and 3D glasses that have been available since 2013.)
✎ If you keep trying to pair the glasses and the TV, the battery level will decrease significantly. However, the battery level will recover to a certain degree in about a minute.
✎ The working distance depends on the existence of obstacles (a person, metal, walls, etc.) between the glasses and the TV and the strength the Bluetooth signal.
✎ Turn off the 3D glasses while they are not in use. If you leave the 3D glasses on, the battery lifespan decreases.
Pairing steps
1. Turn on the TV, and then move the glasses within 19.5 inches of the TV.
2. Press the power button on the 3D glasses briefly. The 3D glasses will power on and pairing will start.
3. The message “3D glasses are connected to TV.” will be displayed on the TV screen when the pairing is successfully completed.
• If pairing fails, the 3D glasses will power off.
• If the first attempt to pair fails, power the TV off and on again and perform step 2.
• How to pair again: Press the power button on the 3D glasses for more than 1 second.
Pairing is needed again in the following situations:
• If the 3D glasses do not function, even when the power button is pressed, especially with a 3D TV after a repair.
• If you want to play 3D content on another Samsung 3D TV model that belongs to the D, E, or F series released in 2011 through 2013. You must pair the glasses with the other TV.
English - 16
[UF6320-XU]BN68-04881B-02ENG.indb 16 2013-11-14 5:04:29
Watching 3D Video
Some 3D modes may not be available depending on the format of the image source.
To watch in 3D, you must wear 3D Active Glasses and turn the glasses on by pressing the power button.
1. Go to the 3D screen. ( Picture > 3D )
2. Select the 3D Mode. The 3D Mode screen appears.
3. Set the 3D Mode of the image you want to view.
Troubleshooting
If you encounter...
My 3D glasses do not work.
The LED keeps blinking
Try this...
Replace the battery.
The 3D glasses should be close to the TV. Make sure that the distance between the TV and your 3D glasses is less than 19.5 feet (6m) in a straight line.
Check the 3D function settings of your TV.
The battery is dead. Replace the battery.
Specifications (Model Number: SSG-5100GB)
Optics
Weight
Power
Power consumption
Operating conditions
Shutters
Recommended operating distance
Glasses
Glasses
Glasses
Battery
Liquid crystal Transmittance
2 ~ 6 m (6.5 to 19.5 ft) Field Rate
36±2%
120 fields/second
21.5 g/.76 oz. (including the battery: 24.0±0.5 g/.85.±.018oz. )
One 3 V lithium/manganese dioxide battery 3 V(CR2025)
0.85 mA (Average)
Type
Operating time
165mAh, 3.0 V (CR2025)
150 hours
Operating temperature
Custody temperature
50 °F ~ 104 °F (10°C ~ 40°C)
-4 °F ~ 113 °F (-20°C ~ 45°C)
✎ Product specifications may be changed without notice in order to enhance product performance.
✎ The continuous operating time may differ depending on the wireless communication environment and usage conditions.
Recommendation - EU Only
Hereby, Samsung Electronics, declares that this 3D Active Glasses is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
This equipment may be operated in all EU countries.
English - 17
[UF6320-XU]BN68-04881B-02ENG.indb 17 2013-11-14 5:04:29
Troubleshooting and Other Information
What is Remote Support?
Samsung Remote Support service offers you one-on-one support with a Samsung Technician who can remotely.
• Diagnose your TV
• Adjust the TV settings for you
• Perform a factory reset your TV
• Install recommended firmware updates
How Does it Work?
Having a Samsung Tech remotely service your TV is really pretty simple
1. Call Samsung
Contact Centre and ask for remote support.
2. Open the menu on your TV and go to the Support section .
3. Select Remote
Management and
Provide the Pin# to the agent.
4. The agent will then access your TV .
That's it!
Password Change
Screen Menu > System > Change PIN
Change the TV's password.
1. Run Change PIN and then enter the current password in the password field. The default password is
0000.
2. Enter a new password and then enter it again to confirm it. The password change is complete.
✎ If you forget the PIN code, press the buttons in the following sequence which resets the PIN to “0-0-
0-0”:
✎ In Standby mode: MUTE → 8 → 2 → 4 → POWER (on).
[UF6320-XU]BN68-04881B-02ENG.indb 18
English - 18
2013-11-14 5:04:30
Troubleshooting
If you have any questions about the TV, first refer to this list. If none of these troubleshooting tips apply, please visit “www.samsung.com,” then click on Support, or contact the call centre listed on the back-cover of this manual.
Issues
The TV won’t turn on.
Solutions and Explanations
• Make sure the AC power cord is securely plugged in to the wall outlet and the TV.
• Make sure the wall outlet is working.
• Try pressing the P button on the TV to make sure the problem is not the remote. If the TV turns on, refer to “Remote control does not work” below.
There is no picture/video.
The remote control does not work.
The cable/set top box remote control doesn’t turn the TV on or off or adjust the volume.
• Check the cable connections. Remove and reconnect all cables connected to the TV and external devices.
• Set the video outputs of your external devices (Cable/Sat Box, DVD, Blu-ray etc) to match the TV's input connections. For example, if an external device’s output is HDMI, it should be connected to an
HDMI input on the TV.
• Make sure your connected devices are powered on.
• Be sure to select the correct input source.
• Reboot the connected device by unplugging it, and then reconnecting the device’s power cable.
• Replace the remote control batteries. Make sure the batteries are installed with their poles (+/–) in the correct direction.
• Clean the sensor’s transmission window on the remote.
• Try pointing the remote directly at the TV from 5~6 feet away.
• Programme the Cable/Set remote control to operate the TV. Refer to the Cable/Set-Top-Box user manual for the SAMSUNG TV code.
✎ This TFT LED panel uses a panel consisting of sub pixels which require sophisticated technology to produce. There may be, however, be a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.
✎ To keep your TV in optimum condition, upgrade to the latest firmware on the Samsung web site by
USB (Samsung.com > Support > Downloads).
✎ Some of above pictures and functions are available at specific models only.
Mounting the TV on the Wall Using the Wall Mount Kit
(Optional)
Wall or Ceiling Mounting
If you mount this product on a wall, it should be mounted only as recommended by the manufacturer. Unless it is correctly mounted, the product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.
Installing the Wall Mount Kit
The wall mount kit (sold separately) lets you mount the TV on the wall.
For detailed information about installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket. We do not advise you to do it yourself. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select to install the wall mount on your own.
English - 19
[UF6320-XU]BN68-04881B-02ENG.indb 19 2013-11-14 5:04:30
Preparing before installing Wall-Mount
Case A. Installing the SAMSUNG Wall-Mount Case B. Installing another company’s Wall-Mount
1
1
8.6 mm
To install a wall-mount, use the Holder-Ring 1 .
Wall Mount Kit Specifications (VESA)
✎ The wall mount kit is not supplied, but sold separately. Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
✎ NOTE
− Standard dimensions for wall mount kits are shown in the table below.
− When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
− Do not use screws that do not comply with the VESA standard screw specifications.
− Do not use screws that are longer than the standard dimension or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the TV set.
− For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications.
− Do not fasten the screws that are too strongly; this may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents.
− Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
− Do not mount the TV at more than a 15 degree tilt.
Product
Family
Inch VESA Spec.(A * B) Standard Screw Quantity
40 200 X 200
LED-TV M8 4
46 400 X 400
Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury due to electric shock.
English - 20
[UF6320-XU]BN68-04881B-02ENG.indb 20 2013-11-14 5:04:31
Storage and Maintenance
✎ If a sticker was attached to the TV screen, some debris can remain after you remove the sticker.
Please clean the debris off before watching TV.
✎ The exterior and screen of the product can get scratched during cleaning. Be sure to wipe the exterior and screen carefully using a soft cloth to prevent scratches.
Do not spray water directly onto the product. Any liquid that goes into the product may cause a failure, fire, or electric shock.
Clean the product with a soft cloth dampened with a small amount of water. Do not use a flammable liquid (e.g. benzene, thinners) or a cleaning agent.
Providing Proper Ventilation for Your TV
When you install your TV, maintain a distance of at least 10 cm between the TV and other objects (walls, cabinet sides, etc.) to ensure proper ventilation. Failing to maintain proper ventilation may result in a fire or a problem with the product caused by an increase in its internal temperature.
✎ Whether you install your TV using a stand or a wall-mount, we strongly recommend you use parts provided by Samsung Electronics only.
• If you use parts provided by another manufacturer, it may cause difficulties with the product or result in injury caused by the product falling.
Installation with a stand.
10 cm
Installation with a wall-mount.
10 cm
10 cm 10 cm
10 cm 10 cm
10 cm
Other Warnings
✎ The actual appearance of the TV may differ from the images in this manual, depending on the model.
✎ Be careful when you touch the TV. Some parts can be somewhat hot.
English - 21
[UF6320-XU]BN68-04881B-02ENG.indb 21 2013-11-14 5:04:31
Assembling the Cable manager
Eco Sensor and Screen Brightness
Eco Sensor measures the light in your room and optimizes the brightness of the TV automatically to reduce power consumption. This causes the TV to brighten and dim automatically. If you want to turn this function off, go to Screen Menu > System > Eco Solution > Eco Sensor
Do not block the sensor with any material. It can decrease picture brightness.
1. Eco Sensor : This power-saving feature automatically adjusts the screen brightness of the TV according to the ambient light intensity detected by the Light Sensor.
2. To enable or disable Eco Sensor , go to Screen Menu > System > Eco Solution > Eco Sensor and select On or Off .
3. Precaution: If you find the screen too dark while watching the TV in a dark area, this may be caused by the Eco Sensor .
English - 22
[UF6320-XU]BN68-04881B-02ENG.indb 22 2013-11-14 5:04:31
Tip Prevention – Securing the TV to the Wall
Caution: Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang on or destabilize the TV. Doing so may cause the TV to tip over, causing serious injuries or death. Follow all safety precautions provided in the Safety Flyer included with your TV. For added stability and safety, you can purchase and install the anti-fall device as described below.
To Avoid the TV from Falling
1. Put the screws into the clamps and firmly fasten them onto the wall. Confirm that the screws have been firmly installed onto the wall.
✎ You may need additional material such as an anchor depending on the type of wall.
✎ Since the necessary clamps, screws, and string are not supplied, please purchase these additionally.
2. Remove the screws from the back centre of the TV, put the screws into the clamps, and then fasten the screws onto the TV again.
✎ Screws may not be supplied with the product. In this case, please purchase the screws of the following specifications.
✎ Screw Specifications
• For a 40 ~ 46 inches: M8
3. Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong cable and then tie the string tightly.
✎ NOTE
− Install the TV near to the wall so that it does not fall backwards.
− It is safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on the TV.
− Untie the string before moving the TV.
4. Verify all connections are properly secured. Periodically check the connections for any sign of fatigue or failure. If you have any doubt about the security of your connections, contact a professional installer.
Wall
[UF6320-XU]BN68-04881B-02ENG.indb 23
English - 23
2013-11-14 5:04:32
Specifications
Specifications - TV
Display Resolution
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Stand Swivel (Left / Right)
Sound
(Output)
Model Name
Screen Size
(Diagonal)
Dimensions (W x H x D)
Body
With stand
Weight
Without Stand
With Stand
UE40F6320
40 inches
934.0 x 548.6 x 49.6 mm
934.0 x 620.1 x 264.8 mm
1920 x 1080
10°C to 40°C (50°F to 104°F)
10% to 80%, non-condensing
-20°C to 45°C (-4°F to 113°F)
5% to 95%, non-condensing
-20˚ ~ 20˚
10 W X 2
UE46F6320
46 inches
1065.4 x 622.5 x 49.6 mm
1065.4 x 704.7 x 306.9 mm
8.9 kg
10.0 kg
11.8 kg
13.5 kg
✎ Design and specifications are subject to change without prior notice.
✎ For information about the power supply, and more about power consumption, refer to the label attached to the product.
✎ Typical power consumption is measured according to IEC 62087 Ed.2
Standby mode
To decrease power consumption unplug the power cord when you don't use the TV for a long time.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset,
USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in countries with separate collection systems)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.
[UF6320-XU]BN68-04881B-02ENG.indb 24
English - 24
2013-11-14 5:04:32
Guides
Licences
Recommendation - EU Only
• Hereby, Samsung Electronics, declares that this LED TV is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
• The official Declaration of Conformity may be found at http://www.samsung.com, go to Support >
Search Product Support and enter the model name.
• This equipment may only be used indoors.
• This equipment may be operated in all EU countries.
Still image warning
Avoid displaying still images (such as jpeg picture files), still image elements (such as TV channel logos, stock or news bars at the screen bottom etc.), or programmes in panorama or 4:3 image format on the screen. Constantly displaying still pictures can cause image burn-in on the LED screen, which will affect image quality. To reduce risk of this effect, please follow the recommendations below:
• Avoid displaying the same TV channel for long periods.
• Always try to display any image in full screen. Use the TV set’s picture format menu for the best possible match.
• Reduce brightness and contrast to avoid the appearance of after-images.
• Use all TV features designed to reduce image retention and screen burn. Refer to the e-Manual for details.
[UF6320-XU]BN68-04881B-02ENG.indb 25
English - 25
2013-11-14 5:04:33
Warranty Card
United Kingdom Republic of Ireland (EIRE)
This Samsung product is warranted for a period of twelve (12) months from the original date of purchase, against defective materials and workmanship. In the event that warranty service is required, you should return the product to the retailer from whom it was purchased. However, Samsung Authorised Dealers and Authorised Service Centres in other EC Countries will comply with the warranty on the terms issued to purchasers in the country concerned. In case of difficulty, details of our Authorised Service Centres are available from:
Samsung Electronics U.K. Ltd.
Customer Care Centre
PO Box 479
GATESHEAD NE9 9BJ
United Kingdom
Tel: 0330 SAMSUNG (7267864) / Fax: 0330 7260001 (UK & Northern Ireland)
Tel: 0818 717100 / Fax: +44 117 915 6736 (EIRE Only)
Web: www.samsung.com
WARRANTY CONDITIONS
1.
The warranty is only valid if, when warranty service is required, the warranty card is fully and properly completed and is presented with the original invoice or sales slip or confirmation, and the serial number on the product has not been defaced.
2.
Samsung’s obligations are limited to the repair or, at its discretion, replacement of the product or the defective part.
3.
Warranty repairs must be carried out by Authorised Samsung Dealers or Authorised Service Centres.
No re-imbursement will be made for repairs carried out by non Samsung Dealers and, any such repair work and damage to the products caused by such repair work will not be covered by this warranty.
4. This product is not considered to be defective in materials nor workmanship by reason that it requires adaptation in order to conform to national or local technical or safety standards in force in any country other than the one for which the product was originally designed and manufactured.
5. This warranty covers none of the following: a) Periodic check ups, maintenance and repair or replacement of parts due to normal wear and tear.
b) Cost relating to transport, removal or installation of the product.
c) Misuse, including the faiure to use this product for its normal purposes or incorrect installation.
d) Damage caused by Lightning, Water, Fire, Acts of God, War, Public Disturbances, incorrect mains voltage, improper ventilation or any other cause beyond the control of Samsung.
e) Spillage of food or liquid or use of any other hazardous substances, which may effect the product.
f) Performance due to differences in broadcasting method between countries
6. This warranty is valid for any person who legally acquired possession of the product during the warranty period.
7. The consumers statutory rights in any applicable national legislation whether against the retailer arising from the purchase contract or otherwise are not affected by this warranty. Unless there is national legislation to the contrary, the rights under this warranty are the consumers sole rights and Samsung, its subsidiaries and distributors shall not be liable for indirect or consequential loss or any damage to records, compact discs, videos or audio taper or any other related equipment or material.
8. Some products may differ from these guidelines. Please check with your dealer or the local Samsung web-site.
[UF6320-XU]BN68-04881B-02ENG.indb 26 2013-11-14 5:04:33
Wiring the Mains Power Supply Plug (UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating must be used.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitably approved extension lead or consult your dealer for assistance.
However, if there is no alternative but to cut off the plug, remove the fuse and then safely dispose of the plug.
Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL BROWN - LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows : The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE LETTER E
OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.
[UF6320-XU]BN68-04881B-02ENG.indb 27 2013-11-14 5:04:33
Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Flat 101.6 cm (40")
- Full HD 1920 x 1080 pixels 16:9
- CMR (Clear Motion Rate) 200
- DVB-C, DVB-T2
- Smart TV Internet TV
- Wi-Fi Ethernet LAN
- 62 W
