Mitox 460UVX Premium Petrol Brushcutter OPERATOR'S MANUAL
Mitox 360UX is a versatile and powerful brushcutter, designed to tackle demanding tasks in various outdoor environments. Its auto-bump feed nylon cutting head efficiently trims grass and weeds, while the metal blade option allows for clearing thicker vegetation and small branches. The adjustable front and rear handles provide personalized comfort during prolonged use.
Advertisement
Advertisement
www.
mitox .co.uk
Operator’s Manual
user manual, maintenance instructions and spare parts
360UX, 460UVX Premium Brushcutter
Read this manual carefully before operating the machine
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
12
11
10
9
3
4
5
8
13
13
12
10
19
19
2
6
2
17
1
15
14
7
20
15
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Component Location
16
17
18
19
20
11
12
13
14
15
6
7
8
9
10
1
2
3
4
5
NYLON CUTTING HEAD
DRIVE SHAFT
THROTTLE TRIGGER
IGNITION SWITCH
SAFETY LEVER
HANDLE
HARNESS ASSEMBLY
PETROL CAP
PURGE BULB
FUEL TANK
AIR CLEANER
CHOKE
STARTER HANDLE
DEBRIS SHIELD
CUT-OFF KNIFE
FRONT HANDLE
GEARBOX
REAR HANDLE
HARNESS FIXING POINT
METAL BLADE
Auto bump feed nylon cutting head.
Contains the drive shaft.
Spring loaded to return to idle when released.
Slide switch, forward to run, back to stop.
Prevents accidental operation of the throttle.
This handle can be adjusted for maximum comfort
Fully adjustable for maximum comfort
Push the purge bulb to remove the air from the fuel system.
Contains fuel and fuel filter
Contains replaceable filter
To help in cold starting
Pull to start the engine
Helps protect the operator from debris
Cuts the nylon line to the correct length
This handle can be adjusted for maximum comfort
For attaching a blade or nylon head to
Incorporating throttle trigger, switch, and safety lever
Fixing point to attach the harness
Metal blade cutting head
Warnings in the Manual
This mark indicates instructions which must be followed in order to prevent accidents which could lead to serious bodily injury or death.
!
IMPORTANT
This mark indicates instructions which must be followed or it leads to mechanical failure, breakdown, or damage.
NOTE
This mark indicates hints or useful directions in the use of the product.
Original Instructions Version November 17
360UX/460UVX_1011171
3
360UX, 460UVX Premium Brushcutter
Safety Symbols
Warning: Danger, Caution
Read the documentation and safety instructions which are provided in this user manual.
When operating this machine, use protective equipment such as goggles, helmet and ear defenders.
Wear security shoes and gloves.
Check the condition of working area to avoid any accident by hitting hidden obstacles such as stumps, stones, cans, or broken glass.
Hot surface: Risk of burn.
Danger: Risk of intoxication.
Danger: Risk of fire or explosion
Directive 2000-14/CE. Guaranteed noise levels
Beware of objects being thrown from the operating zone
Warning: Keep all people, animals and vulnerable objects at least 15 metres from the working area.
4
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Never modify the cutter in any way. Improper use of any cutter can cause serious or fatal injury.
Beware of blade thrust
Taking Care of Warning Labels
Always keep warning labels clean and free of scratches, which might make them illegible or difficult to read. If the warning labels provided with your Brushcutter become damaged, peel off, or otherwise become illegible or difficult to read, order new labels from the authorised servicing dealer and replace the damaged labels. When applying new labels, first wipe away any dirt and dry the surface before applying the new label in the same place as the original label.
Explanation of Symbols on the Machine
For safe operation and maintenance, symbols are carved in relief on the machine:
Fuel tank 2 stroke mix
Position: Fuel cap
CHOKE OPERATION
Starting mode when the engine is hot (choke off).
Position: Air cleaner cover.
Starting mode when the engine is cold (choke on).
Position: Air cleaner cover.
Original Instructions Version November 17
360UX/460UVX_1011171
5
360UX, 460UVX Premium Brushcutter
Safety Precautions
Introduction
Read this Owner/Operator Manual carefully. Be sure you understand how to operate this
Brushcutter properly before you use it. Failure to do so could result in serious injury.
Keep this manual handy so that you may refer to it later whenever any questions arise. Also note that you are able to contact the dealer from whom you purchased the product for assistance.
Always include this manual when selling, lending, or otherwise transferring the ownership of this product.
This product has been designed to be used as a Brushcutter power tool as described previously and it should never be used for any other purpose; doing so could result in unforeseen accidents and injuries occurring. Only approved Mitox accessories should be used with this product.
This Brushcutter is equipped with extremely sharp blades, always wear sturdy gloves when handling the blades and fit the safety guards when not in use.
When using this Brushcutter for the first time, take the Brushcutter to a wide, clear, open space, start the engine, and practice handling the Brushcutter until you are sure that you will be able to handle it properly in actual operation.
You should never use this Brushcutter when under the influence of alcohol, suffering from exhaustion or lack of sleep, suffering from drowsiness as a result of having taken medicine, or at any other time when your judgement might be impaired or that you might not be able to operate the Brushcutter properly and in a safe manner.
Never allow children or anyone unable to fully understand the directions given in this manual to use this Brushcutter
When planning your work schedule, allow plenty of time to perform the work and allow plenty of time for rest. Limit the amount of time you continuously use the Brushcutter to 30~40 minutes per session and take 10~20 minutes of rest between work sessions. Also, try to keep the total amount of work performed in a single day to 2 hours.
Never run the engine indoors as the exhaust gases contain harmful carbon monoxide.
6
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Never use the Brushcutter in conditions as described below:
When the ground is slippery or when other conditions exist which might make it difficult to maintain a steady posture while using the Brushcutter.
•
•
•
•
•
•
At night, at times of heavy fog, or at any other times when your field of vision is limited and it would be difficult to gain a clear view of the area where the Brushcutter is to be used. In heavy rain, during lightning storms, at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use this product.
Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn can lead to accidents and injury.
Work Clothing and Safety Equipment
When using the product, you should wear proper clothing and protective equipment.
Helmet
Protection goggles or face protector
Ear protectors
Thick work gloves
Non-slip sole work boots
When using your Brushcutter, always wear strong, durable, work clothing; shirts
should be long-sleeved and trousers should be full-length.
Safety and Operation
This Brushcutter is equipped with a very sharp blade, and when used incorrectly the blade can be extremely dangerous.
Improper handling can cause accidents which may in turn lead to serious injury or death. For
Original Instructions Version November 17
360UX/460UVX_1011171
7
360UX, 460UVX Premium Brushcutter this reason, you should always be careful to adhere to the following instructions when using your
Brushcutter.
Never hold the Brushcutter in a way in which the cutting head is pointing towards someone else.
Never allow the blade to come into contact with your body.
Always turn off the engine before adjusting the Brushcutter, or at any time when coming into close proximity with the cutting head.
Always wear thick work gloves when adjusting the Brushcutter.
Safe Handling of Fuel
The engine of the Brushcutter is designed to run on a two stroke oil/fuel mixture.
This fuel is highly flammable, never store cans of fuel or refill the fuel tank in any place where there is a source of heat or fire, which might ignite the fuel.
Do not smoke whilst operating the Brushcutter or refilling, keep lit cigarettes away from the
Brushcutter at all times.
When refilling the fuel tank always stop the engine first and carefully make sure that there are no sparks or naked flames anywhere nearby before refuelling.
If any fuel spillage occurs during refuelling, use a dry rag to wipe any fuel which has been spilled onto the Brushcutter before starting the engine.
After refuelling, screw the fuel cap back tightly onto the fuel tank and carry the Brushcutter to a spot 5 metres or more away from where it was refuelled before starting the engine.
8
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Before Operating the Brushcutter
Before beginning work, carefully check the work area and remove any obstacles. Within a perimeter of 15 metres of the work area should be considered a hazardous area into which noone should enter while the Brushcutter is being used, and when necessary this area should be marked with a warning rope, warning signs, or other forms of warning.
When work is to be performed simultaneously by two or more operators, care should also be taken to constantly look around to check the presence and locations of other operators within the work area to maintain a safe distance between each operator.
Before beginning work, each component of the Brushcutter should be checked to make sure that it is in proper working order, make sure that there are no loose screws or bolts, fuel leaks, ruptures, dents, broken guards or any other problems which might interfere with safe operation.
Keep all parts of your body away from the cutting head when the engine is running.
Before Starting the Engine
Carefully check the work area to make sure that no obstacles exist within a perimeter of 15 metres around the Brushcutter before starting the engine.
To start the engine, place the Brushcutter onto the ground in a flat clear area and hold it firmly in place to ensure that neither the cutting head nor the throttle come into contact with any obstacles when the engine starts.
After starting the engine, make sure that the cutting head stops moving when the throttle trigger is released (idle). If the cutting head continues to move when the engine is at idle, adjust the idle screw on the carburettor to a point where the cutting head stops moving, if this cannot be achieved, take the Brushcutter to your authorised service dealer for adjustment.
Original Instructions Version November 17
360UX/460UVX_1011171
9
360UX, 460UVX Premium Brushcutter
Avoid Noise Problems
Check and follow the local regulations for sound levels and hours of operation for garden machinery.
In general, operate Brushcutters between 8 am and 5 pm on weekdays and 9 am to 5 pm at weekends.
•
•
•
•
•
•
•
•
•
•
10
Avoid using the Brushcutter late at night and/or early in the morning.
Safety when using the Brushcutter
When using the Brushcutter, grip the handles firmly with both hands, place your feet slightly apart so your weight is distributed evenly across both legs, and always maintain a steady even posture while working.
Maintain full engine speed when cutting.
Never allow other persons to come within the work area as doing so might expose them to danger.
Keep work area clear of all persons, particularly small children and pets. Injury may result from flying debris.
If grass or other objects get caught in the Brushcutter during operation, always stop the engine before removing the object.
Never touch the spark plug or plug HT cable while the engine is in operation, doing so may result in an electrical shock.
Never touch the exhaust, spark plug, or any metallic parts while the engine is in operation or immediately after shutting down the engine.
These parts reach high temperatures during operation and doing so could result in serious burns.
When you finish cutting in one location and wish to continue work in another area, stop the engine.
Always remove fuel from the fuel tank before transportation to prevent fuel spillage.
Never leave the Brushcutter exposed to direct sunlight as this can heat the fuel tank and may cause a discharge of fuel, and flood the engine.
Be careful not to hit the nylon cutting head against stones or the ground.
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Two-Stroke Fuel
Fuel is very flammable. Do not smoke or bring any flame or sparks near fuel.
Always stop the engine and allow it to cool before refuelling.
Refuel outdoors on bare ground, restart engine at least 5m away from the refuelling stop.
The engine is lubricated by oil mixed into petrol. Prepare a mixture of unleaded petrol and semisynthetic two-stroke oil that meets the specifications of: API TC, ISO-L-EGC, JASO FC (Low Smoke) oil.
Recommended mixing ratio is 40:1
FUEL WITH NO OIL (RAW PETROL) will cause severe damage to the engine which is not covered by manufacturer’s warranty.
Use fresh, unleaded petrol (95 RON) and semi-synthetic oil specially made for high performance two-stroke engines. Mix in a ratio of 40 parts petrol to 1 part of oil.
By using two-stroke oil specially made for two-stroke engines you will reduce the formation of ash and carbon deposits on the spark plug, piston, exhaust muffler and cylinder as well as reducing emissions of harmful exhaust gases.
Oil FOR 4-CYCLE ENGINES should not be used as two-stroke lubrication oil as it can cause fouling of the spark plug, exhaust port blocking, piston ring sticking and other internal engine damage.
NOTE
Due to increased Ethanol content in petrol we recommend the use of B3C Ethanol Shield
2-Stroke Oil, and Ethanol Shield Fuel Stabiliser to protect your MITOX® engine against the harmful effectsof Ethanol. www.b3cfuel.co.uk
Original Instructions Version November 17
360UX/460UVX_1011171
11
360UX, 460UVX Premium Brushcutter
Fuel Storage
Mixed two-stroke fuel which has been left unused for a period of one month or more may damage the carburettor and result in the engine failing to start or operate correctly.
When storing the Brushcutter for a period of more than one month, empty the fuel tank, and run the engine to empty the carburettor of fuel.
Two stroke fuel can cause deterioration of rubber and/or plastic components during prolonged storage.
It is important to only use good quality, fresh fuel mix.
Fuelling
Shake the fuel container to thoroughly mix the two-stroke oil and petrol.
Clean dirt from around the fuel cap before removing.
Pour two-stroke fuel into the fuel tank with a filtered funnel, up to 80% of the fuel tank's capacity.
Replace the fuel cap and tighten securely. Spilled fuel must be wiped away from the Brushcutter before starting the engine.
Move at least 5m away from the refuelling area before restarting the engine.
When refilling the tank, always turn off the engine and allow it to cool down. Take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refuelling.
12
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Assembly of the Brushcutter
The blade fitted to the guard is sharp and can cause injury, always wear gloves.
The guard extension shall always be fitted when using the trimmer head. The guard extension shall always be removed when using the grass blade.
Installing the Guard
A
C
B
• Hook the blade guard/combination guard onto the fitting on the shaft and secure
with special bolt (A).
• Guide the lower guard extension pegs (B) into the slots of the upper guard (C), then
Secure by clicking (B) into (C).
Original Instructions Version November 17
360UX/460UVX_1011171
13
360UX, 460UVX Premium Brushcutter
Installing the 3 Tooth Blade
Lay the Brushcutter on its back with the gearbox shaft facing up.
A
B
Rotate the gear box shaft until the hole in the holder
(a) lines up with the slot in the metal guard (b).
A
Place the 3 tooth blade on the holder (a), centring the blade on the raised centre.
B
A
B
Insert an Allen key or screwdriver into the hole in the gearbox cover
(a) and into holder (b).
Fit the holder
(b) over the blade.
C
B
Fit the domed nut protector (c) over holder (b) and the blade.
Fit the nut anticlockwise (turn left) and tighten using the spanner provided. Remove the Allen key / screwdriver.
THE BLADE MUST BE CORRECTLY POSITIONED ON THE UPPER BLADE CLAMP
OTHERWISE SERIOUS DAMAGE AND INJURY TO PERSONS AND PROPERTY COULD
RESULT.
14
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Installing the Nylon Head
Lay the Brushcutter on its back with the gearbox shaft facing up.
A
B
A
Rotate the gear box shaft until the hole in the holder (a) lines up with the slot in the metal guard (b).
Insert an Allen key or screwdriver into the hole in the gearbox cover and into holder (a).
Screw the nylon head anti-clockwise
(turn left) onto the threaded shaft on the end of the gearbox.
Make sure that the nylon head is securely locked in position and remove the Allen key.
Original Instructions Version November 17
360UX/460UVX_1011171
15
360UX, 460UVX Premium Brushcutter
16
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
•
•
•
Using the Brushcutter
Choosing the cutting device
Choose the most suitable cutting device for the job to be done, according to these general indications:
•
•
The cutting line head can eliminate tall grass and non-woody vegetation
The 3-point blade is suitable for cutting brushwood and small shrubs up to 2 cm in diameter.
Nylon Head
• Cut the grass in 1.5 metre widths, keeping the machine well balanced.
Avoid engaging stones, piles of earth, small pieces of wood or anything that could be hidden or difficult to see in the grass. If a large object is accidentally struck, if the cutting head gets blocked, overloaded or stringy material gets wrapped in the cutting head, reduce the engine speed so the engine idles. Make sure that the cutting head has stopped rotating switch off the engine and remove the material.
Put the Brushcutter on the ground and check that the cutting head has not been damaged. If necessary, change the cutting head. If the head is only wrapped by vegetation, remove by hand and clean the cutting head.
Always wear safety gloves for this operation and ensure the engine is switched off and the head is stationary.
• When the 2 nylon cords become too short, accelerate the engine and bump the nylon head on the ground. Automatically the 2 nylon cords will feed out and be cut to the correct length. Repeat the operation if necessary.
3-Point Blade
• Start cutting above the undergrowth and then move down with the blade so as to cut the brush into small pieces.
• Avoid hitting stones, piles of earth, small pieces of wood or anything that could be hidden or difficult to see in the grass.
Original Instructions Version November 17
360UX/460UVX_1011171
17
360UX, 460UVX Premium Brushcutter
Installing the U Handle Assembly (460UVX)
• Remove the upper bracket from the assembly by undoing the Lockscrew.
• Install the U handle assembly, reassemble the bracket assembly and secure using the
Lockscrew.
•
18
Ensure that the controls are located on the right and adjust the handle for maximum comfort before securing.
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Installing the U Handle Assembly (360UX)
Lockscrew
Washer
Upper Bracket
To Right handle
Lower Bracket
To Left handle
Drive Shaft To
Cutter Head
Drive Shaft
To Engine
• Remove the upper bracket from the assembly by undoing the Lockscrew.
• Install the U handle assembly, reassemble the bracket assembly and secure using the
Lockscrew.
• Ensure that the controls are located on the right and adjust the handle for maximum comfort before securing.
Original Instructions Version November 17
360UX/460UVX_1011171
19
360UX, 460UVX Premium Brushcutter
Operation
Keep clear of the cutter head as it may start moving when the engine starts.
Starting the Engine
CAUTION do not pull the starter cord all the way out and do not let go of the starter handle when the cord is extended, this can damage the starter mechanism.
The switch will automatically return to the 'On' position. Wait 10 seconds before attempting to restart the engine to allow the switch to reset
Cold Engine Starting
Rest the unit on a flat, firm surface. Keep the cutting head off the ground and clear of surrounding objects as it may start moving when starting the engine.
a). Starting: Ignition Switch automatically set in the ( I ) position.
b). Primer bulb: Press the primer bulb repeatedly until fuel begins to fill the bulb.
The bulb need not be completely filled.
(d) c). Choke: Set the choke lever in the choke ( ) position (on front of engine)
20 d). While holding the unit, pull out the starter rope firmly until engine fires
(indicated by a ‘cough’ from the engine).
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
(f)
(e) e). Move the choke lever to the open
( ) position.
f). Repeat pulling the cord until the engine starts. When the engine starts, allow the engine to warm up with the throttle pulled slightly.
Allow the engine to warm up before use. When cutting, always use the Brushcutter on full throttle.
Hot Engine Starting
•
•
•
Set the ignition switch to the START ( I ) position.
Check the clear return fuel line. If the line is empty, push the air purge bulb until fuel is visible in the clear return fuel line.
Move the choke lever to the closed ( ) position, then back to the open ( )
position. This will set the throttle to the hot start position.
• Pull the starter rope until the engine starts, then squeeze the throttle briefly to release
• the fast idle control and return the engine to idle.
If the engine does not start after 5 pulls, use the Cold Start procedure.
Overchoking
Should the engine become flooded due to overchoking, turn the ignition switch off, unscrew the spark plug, wipe it dry or replace.
Stopping the Engine
NOTE
Switch automatically set in the "I" position.
Set the engine to idling by releasing the throttle lever.
Set the ignition switch to the off position ‘’O’’ (STOP).
If the engine fails to stop, set the choke lever to the closed position to stall the engine; do not use the machine until the ignition switch is repaired.
Original Instructions Version November 17
360UX/460UVX_1011171
21
360UX, 460UVX Premium Brushcutter
Running In
During the first ten hours of work, avoid running the engine at maximum speed for a prolonged period until all the components have bedded in, after the engine has been run in, it will reach its maximum power.
Transportation
Never transport the Brushcutter with the engine running. An engine that is running could be accidently accelerated causing the blade to engage.
Make sure the blade safety guards are in place when transporting the Brushcutter.
When carrying by hand, the cutting head should be pointing backwards.
Ensure the Brushcutter is secure when transporting in a vehicle and the tank is drained of fuel.
Maintenance
IMPORTANT
After every use, check that all nuts, bolts and screws are securely fastened and tighten if necessary.
In the event of an accident, breakdown or blockage, ensure the engine is turned off before any work is carried out to rectify this.
Make sure the engine has stopped and is cool before performing any service to the machine.
Contact with moving cutting head or hot muffler may result in a personal injury.
Fuel Filter
Every 15 hours of operation, using a wire hook, take the fuel filter from the fuel tank and clean or replace with a new fuel filter.
22
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Spark Plug
0.6 - 0.7mm
Poor starting or misfiring is often caused by a fouled or defective spark plug, clean and reset the gap to 0.65 mm, or replace the spark plug with RCJ7Y (Champion) as necessary.
Air Filter
Images are for illustrative purposes only.
The air filter must be regularly cleaned to remove dust and dirt in order to avoid:
- Carburettor
- Starting problems
- Loss of engine power
- Unnecessary wear to engine parts
- Excessive fuel consumption
Clean the filter every 25 hours, or more regularly if conditions are exeptionally dusty.
Original Instructions Version November 17
360UX/460UVX_1011171
23
360UX, 460UVX Premium Brushcutter
Carburettor
The carburettor is adjusted at the factory; if adjustment is required it must be performed by your authorised Mitox dealer.
If the head rotates at idle speed, stop the machine and return it to your authorised
Mitox dealer for repair.
Safety Lock
(c)
(b)
The safety lock is to prevent the throttle lever from accidentally being engaged. The throttle lever
(b) can only be pressed in if the safety lock (c) is held down. Check if the safety lock and throttle lever returns to its original position and the engine returns to idling when you release your hand from the handle.
Any defects contact your nearest service agent for repairs before using the machine.
24
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Storage
•
•
Remove the spark plug; pour a small amount of oil into the cylinder. Rotate the crankshaft several times using the starting rope in order to distribute the oil. Put the spark plug back in.
Remove the fuel from the machine.
Gear Case
(a)
• Remove the bolt (a) on the gear case, top up the gearbox using Lithium grease and refit the bolt, every 15 hours use.
Original Instructions Version November 17
360UX/460UVX_1011171
25
360UX, 460UVX Premium Brushcutter
Replacing the Nylon Cord
Check to see if the nylon head is damaged before replacing the cord. If you can see serious traces of wear or damage, you must replace the complete nylon head.
(b)
(a)
(d)
(c)
(a)
(g) (g)
(f)
(e)
(f)
Images are for illustrative purposes only. Actual head design may vary, however the method remains the same.
1. Stop the engine.
2. Open the nylon head by pushing on the catch, (a), and lifting the cover (b).
3. Pull the bobbin out of the nylon head and take out the rest of the nylon cords.
4. Cut a new length of cord, 2.4mm Ø and 5 metres long.
5. Fold the new cord in half and place the centre of the fold (c) into the clip (d) in the empty bobbin.
6. Wind the line in the direction of the arrows on the bobbin, with half of the line above and half below the divider (e). Maintain an even and firm tension onto the bobbin, being careful not to twist the line.
6. After winding the cord, insert both ends into the notches on the bobbin, (f).
7. Put the filled bobbin back into the carrier. Release the cords from the notches in the bobbin and thread them into the eyelets in the carrier (g). The cords should stick out appx 15 cm either side.
8. Refit the spool cover (b), ensuring it is securely clicked into place.
Never use a cutting device other than those supplied by the manufacturer. (Steel cord is never allowed) Always use original spare parts in order to benefit from continuous warranty.
26
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
•
•
•
•
•
•
Troubleshooting
Engine will not start, power loss:
Check that the fuel tank is not empty. Fill with mixed fuel.
The fuel does not reach the carburettor. Change the fuel filter in the fuel tank.
There is water in the fuel. Drain and clean the fuel system.
The air filter is dirty. Clean or replace the air filter.
There are carbon deposits in the exhaust muffler restricting the engine. Clean or change the muffler.
Spark plug is worn. Replace spark plug.
Original Instructions Version November 17
360UX/460UVX_1011171
27
360UX, 460UVX Premium Brushcutter
Maintenance Timescale
The following intervals apply to normal operating conditions only. If your daily working time is longer or operating conditions are difficult (very dusty work area, etc.), shorten the specified intervals
Complete machine
Control handle
Visual inspection (condition, wear, leaks)
Clean
Control handle Check operation
Air filter Clean
Filter in fuel tank
Replace
Check
Carburettor
Replace filter
Adjustments by Mitox Dealers only
Spark plug Readjust electorde gap
Replace after 100 hours of operation
Cooling inlets Clean
All accessible screws
Check
Anti-vibration elements
Retighten
Check
Safety labels
Muffler
Replace
Replace
Clean
*
*
*
*
*
*
*
*
*
*
* *
* *
*
* *
*
*
*
*
*
*
*
*
*
28
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Specifications
Model 360UX PREMIUM
Capacity
Power
36.3 cm
3
1.6 kw
Weight (without fuel, harness, cutting attachment and guard)
8.2 kg
Maximum engine rotation speed
Speed of output shaft
9500 for grass trimmer,
10500 for brush cutter min for brush cutter
-1
7340 for grass trimmer, 8150
460UVX PREMIUM
46.5 cm
3
1.95 kw
8.7 kg
10000 for grass trimmer,
10500 for brush cutter min
-1
7750 for grass trimmer, 8150 for brush cutter
Idling speed
New Shaft
Handle
Spark plug
Straight
Bike
3000 ± 400
Straight
Full AV Bike
CHAMPION RZ7C
Mixture (petrol: 2-stroke oil)
40:1
Fuel tank capacity
Measured acoustic power level
Measurement uncertainty
110.3 dB(A)
3
Acoustic power level guaranteed
Vibration level - Nylon Head
- Left handle
- Right handle
Measurement uncertainty
4.64 m/s
2
4.53 m/s
2
1.5 m/s
2
1000 ml
111.7 dB(A)
3
114
4.36 m/s
3.12 m/s
1.5 m/s
2
2
2
Vibration level - Metal Blade
- Left handle
- Right handle
Measurement uncertainty
4.79 m/s
2
5.18 m/s
2
1.5 m/s
2
4.17 m/s
2.63 m/s
2
1.5 m/s
2
2
Original Instructions Version November 17
360UX/460UVX_1011171
29
360UX, 460UVX Premium Brushcutter
30
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
360UX Parts - Engine Unit
ID PART NUMBER DESCRIPTION
1 MIC36.1104.0001
2 MIC36.1104.0002
3 MIGB/T3452.1
3.63X2.62
4 MIC36.1104.0200
5 MIGB/T2671.2
M5X45
SCREW
AIR FILTER COVER
O-RING
AIR FILTER
SCREW M5X45
6 MIC36.1104.0004
7 MIC36.1101.0100
8 MIGB/T2671.2
M5X25
AIR FILTER BASE
CARBURETOR
SCREW M5X25
9 MIA38.0301.0010
10 MIC36.1101.0200
CARB GASKET
MANIFOLD
11 MIGB/T845 ST4X10 SCREW ST4X10
12 MIC36.1101.0002
INLET GASKET
13 MIC36.1101.0101
14 MIC36.1104.0005
15 MI01.01.4111
16 MIC36.1101.0003
17 MIA45.0806.0400
18 MIC36.1101.0400
19 MIGB/T2671.2
M5X14
20 MIGB/T2671.2
M4X14
21 MIC36.1101.0303
22 MIC36.1101.0304
CHOKE LEVER
COVER
SCREW ST4.8X14
SPARK PLUG COVER
SPARK PLUG
ENGINE COVER
SCREW M5X14
SCREW M4X14
REAR COVER
GASKET
23 MIC36.1101.0301
24 MIC36.1101.0302
25 MIC36.1106.0200
26 MIGB/T2671.2
M5X20
27 MIC36.1106.0301
CYLINDER
FRONT COVER
IGNITION COIL
SCREW M5X20
WIRE A
28 MIC36.1106.0302
29 MIC36.1101.0006
30 MIC36.1101.0007
31 MIC36.1105.0000
32 MIGB/T2671.2
M6X60
33 MIC36.1101.0005
34 MIC36.1103.0002
35 MIA38.0303.0003
36 MIC43.0103.0300
37 MIC36.1103.0001
WIRE B
MUFFLER GASKET
HEAT SHIELD
MUFFLER
SCREW M6X60
CYLINDER GASKET
PISTON RING
PISTON PIN CIRCLIP
BEARING
PISTON
38 MIC36.1103.0003
39 MIC36.1101.0008
40 MIA62.0113.0005
41 MIGB/T2671.2
M5X16
42 MIC36.1101.0010
43 MIGB/T755 M10
44 MIC36.1101.0501
45 MIC43.0101.0009
46 MIGB/T6187 M8
47 MIC36.1106.0100
48 MIGB/T119 B5X10
49 MIC43.0101.0300
PISTON PIN
TANK GUARD
HEAT INSULATION
SCREW M5X16
CLUTCH BOLT
WASHER M10
CLUTCH ASSEMBLY
FLAT WASHER
FLANGE NUT M8
FLYWHEEL
PIN 5X10
OIL SEAL
50 MIC36.1102.0002
51 MIGB/T276 6202
CRANKCASE LH
BEARING 6202
52 MIC36.1102.0003
CRANKCASE GASKET
53 MIGB/T1099 3X5X13 KEY
54 MIC36.1103.0100
55 MIC36.1102.0001
56 MIA38.0302.0200
57 MIGB/T2671.2
M5X30
CRANKSHAFT ASSEMBLY
CRANKCASE RH
OIL SEAL
SCREW M5X30
Original Instructions Version November 17
360UX/460UVX_1011171
31
360UX, 460UVX Premium Brushcutter
360UX Parts - Engine Unit
ID PART NUMBER
58 MIGB/T97.1 M8
59 MIC36.1101.0600
60 MIGB/T6175 M8
DESCRIPTION
FLAT WASHER M8
PAWL ASSEMBLY
NUT M8
61 MIC36.1110.0000
STARTER ASSEMBLY
62 MIGB/T2672 M5X14 SCREW M5X14
63 MIGB/T96 M5
64 MIC43.2110.0006
PLATE WASHER M5
RATCHET WHEEL
65 MIC36.1110.0005
66 MIC43.2110.0003
67 MIC43.2110.0004
68 MIA36.0110.0003
71 MIA45.0110.0006
72 MIA41.1110.0003
73 MIA45.0111.0200
74 MIC36.1107.0003
SPRING
RECOIL PULLEY
SPRING HOUSING
RECOIL SPRING
STARTER ROPE
STARTER GRIP
TANK VENT
VENT PIPE
75 MIC36.1107.0002
76 MIC43.1107.0003
77 MIC36.1107.0001
78 MIA42.1111.0300
79 MIC36.1107.0000
80 MIA38.0311.0500
81 MIA45.0102.0103
82 MIC36.1101.0009
83 MIC36.1108.0100
84 MIGB/T893.1 35
RETURN PIPE
TANK GROMMET
FUEL PIPE
TANK CAP ASSEMBLY
FUEL TANK ASSEMBLY
FUEL FILTER
CLAMP
FUEL TANK HOUSING
CLUTCH DRUM
CIRCLIP 35
BEARING 6202-2RS 85 MIGB/T276 6202-
2RSP5
86 MIC36.1101.0004
87 MIC36.1108.0001
88 MIGB/T894.1 15
PLATE
CLUTCH DRUM HOUS-
ING
CIRCLIP 15
32
ID PART NUMBER DESCRIPTION
89 MIC45.6808.0001
AV RUBBER
90 MIC45.6808.0002
CLAMP
91 MIGB/T2671.2
M6X25
SCREW M6X25
92 MIGB/T893.1 45 CIRCLIP 45
92 MIC36.1101.0013
HEAT INSULATION
93 MIC36.1101.0014
HEAT INSULATION A
94 MIC36.1101.0015
HEAT INSULATION B
95 MIC36.1101.0016
HEAT INSULATION C
96 MIC36.1101.0011
HOUSING SLEEVE
97 MIC36.1111.0106
CABLE CLIP
98 C36.1111.0106
CABLE CLIP
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Original Instructions Version November 17
360UX/460UVX_1011171
33
360UX, 460UVX Premium Brushcutter
360UX Parts - Shaft Assembly
19
20
21
22
16
17
18
12
13
14
15
10
11
8
9
6
7
4
5
23
24
25
26
27
ID
1
3
28
29
34
PART NUMBER
MIC36.1800.0100
MIGB/T2671.2
M5X20
MIC27.6111.0203
MIC27.6111.0206
MIGB/T41 M8
MIC27.6111.0204
MIC27.6111.0202
MIC27.6111.0201
MIGB/T96 M8
MIC27.6111.0205
DESCRIPTION
SHAFT ASSEMBLY
SCREW M5X20
LEFT CLAMP
AV RUBBER
NUT M8
RIGHT CLAMP
LOWER CLAMP
UPPER CLAMP
WASHER M8
LOCK KNOB
MIGB/T5782 M8X60 SCREW M8X60
MIC43.1100.0003
CABLE CLIP
MIC33.2112.0204
MIGB/T6170 M5
HARNESS LOOP
NUT M5
CLAMP
SUPPORT
SCREW M5X22
MIC33.2112.0203
MIC33.2112.0201
MIGB/T2671.2
M5X22
MIC43.2111.0001
MIC43.2111.0201
MIC43.2111.0202
MIGB/T2671.2
M5X45
MIGB/T56 M5
MIC24.0113.0101
HANDLE TUBING
GRIP
CLAMP
SCREW M5X45
NUT M5
UPPER GUARD
MIC24.0113.0105
MIC24.0113.0104
MIGB/T6564
ST4.2X13
MIC43.2113.0309
MI00.06.04.106
LOWER GUARD
CUTTING BLADE
SCREW ST4.2X13
SCREW ST4.8X19
GUARD CLAMP
30
31
MIC43.2113.0307
MIGB/T2671.2
M6X25
LOCK SCREW
SCREW M6X25
32 MIGB/T2671.2
M6X12
MIC43.B116.0000
SCREW M6X12
33
33-1 MIGB/T893.1 28
33-2 MIGB/T894.1 12
GEAR CASE ASSEMBLY
26MM
CIRCLIP 28
CIRCLIP 12
33-3 MIGB/T276 6001-2Z BEARING 6001-2Z
33-4 MIC48.B116.0002
PINION
33-5 MIGB/T5781 M6X8 SCREW M6X8
33-7 MIGB/T276 6000-2Z BEARING 6000-2Z
33-8 MIC43.B116.0004
33-9 MIC43.B116.0003
33-10 MIGB/T276 6002-
2RSP5
GEAR
GEAR SHAFT
BEARING 6002-2RS
33-11 MIGB/T893.1 32
33-12 MIC43.B116.0006
33-13 MIC43.B116.0005
33-14 MIC43.B116.0007
33-15 MIGB/T6177.2
M10X1.25
34 MI TBC
35
36
MIC43.1100.0001
MIC36.1111.0300
CIRCLIP 32
HOLDER A
HOLDER B
PROTECTOR
FLANGE NUT
M10X1.25
NYLON HEAD AS-
SEMBLY
BLADE
36-1
36-3
MIC43.1111.0700
MIC36.1111.0107
36-4 MIC43.2111.0106
36-6 MI01.01.3121
36-7 MIGB/T2671.2
M5X35
THROTTLE CONTROL
ASSEMBLY
SWITCH
SAFETY LEVER SPRING
LOCK TRIGGER
SCREW ST4X14
SCREW M5X35
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
360UX Parts - Shaft Assembly
36-8 MIGB/T97.1 M5
36-9 MIGB/T845
ST3.5X9.5
36-10 MIC36.1111.0108
36-11 MIC43.2111.0104
36-12 MIC43.2111.0103
36-13 MIC36.1111.0302
36-14 MIC36.1111.0301
WASHER M5
SCREW ST3.5X9.5
TRIGGER SPRING
ROD
TRIGGER
WIRE ASSEMBLY
THROTTLE CABLE AS-
SEMBLY
Original Instructions Version November 17
360UX/460UVX_1011171
35
360UX, 460UVX Premium Brushcutter
36
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
460UVX Parts - Engine Unit
ID PART NUMBER DESCRIPTION
1 MIC36.1104.0001
2 MIC36.1104.0002
3 MIGB/T3452.1
3.63X2.62
4 MIC36.1104.0200
5 MIGB/T2671.2
M5X45
SCREW
AIR FILTER COVER
O-RING
AIR FILTER
SCREW M5X45
6 MIC36.1104.0004
7 MIC36.1101.0100
8 MIGB/T2671.2
M5X25
AIR FILTER BASE
CARBURETOR
SCREW M5X25
9 MIA38.0301.0010
10 MIC36.1101.0200
CARB GASKET
MANIFOLD
11 MIGB/T845 ST4X10 SCREW ST4X10
12 MIC36.1101.0002
INLET GASKET
13 MIC36.1101.0101
14 MIC36.1104.0005
15 MI01.01.4111
16 MIC36.1101.0003
17 MIA45.0806.0400
18 MIC36.1101.0400
19 MIGB/T2671.2
M5X14
20 MIGB/T2671.2
M4X14
21 MIC46.1101.0303
22 MIC36.1101.0304
CHOKE LEVER
COVER
SCREW ST4.8X14
SPARK PLUG COVER
SPARK PLUG
TOP HOUSING
SCREW M5X14
SCREW M4X14
REAR COVER
GASKET
23 MIC46.1101.0301
24 MIC46.1101.0302
25 MIC36.1106.0200
26 MIGB/T2671.2
M5X20
27 MIC36.1106.0301
CYLINDER
FRONT COVER
IGNITION COIL
SCREW M5X20
WIRE A
28 MIC36.1106.0302
29 MIC36.1101.0006
30 MIC36.1101.0007
31 MIC36.1105.0000
32 MIGB/T2671.2
M6X60
33
34
35
36
42
43
44
45
MIC36.1101.0005
MIC46.1103.0002
MIA38.0303.0003
MIC43.0103.0300
37 MIC46.1103.0001
38 MIC46.1103.0003
39 MIC36.1101.0008
40 MIA62.0113.0005
41 MIGB/T2671.2
M5X16
MIC36.1101.0010
MIGB/T755 M10
MIC36.1101.0501
MIC43.0101.0009
WIRE B
MUFFLER GASKET
HEAT SHIELD
MUFFLER
SCREW M6X60
BASE GASKET
PISTON RING
PISTON PIN CIRCLIP
BEARING
PISTON
PISTON PIN
FUEL TANK GUARD
INSULATION
SCREW M5X16
46 MIGB/T6187 M8
47 MIC36.1106.0100
FLANGE NUT M8
FLYWHEEL
48 MIGB/T119 B5X10 PIN 5X10
49 MIC43.0101.0300
OIL SEAL
50 MIC36.1102.0002
51 MIGB/T276 6202-
2RSP6
52 MIC36.1102.0003
53 MIGB/T1099
3X5X13
54 MIC36.1103.0100
55 MIC36.1102.0001
CLUTCH BOLT
WASHER M10
CLUTCH ASSEMBLY
FLAT WASHER
CRANKCASE L/H
BEARING 6202 P6
GASKET
KEY
CRANKSHAFT ASSEMBLY
CRANKCASE R/H
Original Instructions Version November 17
360UX/460UVX_1011171
37
360UX, 460UVX Premium Brushcutter
460UVX Parts - Engine Unit
56 MIA38.0302.0200
57 MIGB/T2671.2
M5X30
58
59
60
61
MIGB/T97.1 M8
MIC36.1101.0600
MIGB/T6175 M8
MIC36.1110.0000
OIL SEAL
SCREW M5X30
WASHER M8
PAWL ASSEMBLY
NUT M8
STARTER ASSEMBLY
62 MIGB/T2672 M5X14 SCREW M5X14
63 MIGB/T96 M5 PLATE WASHER M5
64 MIC43.2110.0006
65 MIC36.1110.0005
RATCHET WHEEL
SPRING
66 MIC43.2110.0003
67 MIC43.2110.0004
68 MIA36.0110.0003
71 MIA45.0110.0006
72 MIA41.1110.0003
73 MIA45.0111.0200
74 MIC36.1107.0003
75 MIC36.1107.0002
RECOIL PULLEY
SPRING HOUSING
RECOIL SPRING
RECOIL ROPE
GRIP
TANK VENT
VENT PIPE
RETURN FUEL LINE
76 MIC43.1107.0003
77 MIC36.1107.0001
78 MIA42.1111.0300
79 MIC36.1107.0000
80 MIA38.0311.0500
81 MIA45.0102.0103
82 MIC36.1101.0009
83 MIC36.1108.0100
84 MIGB/T893.1 35
85 MIGB/T276 6202-
2RSP5
TANK GROMMET
FUEL PIPE
TANK CAP ASSEMBLY
FUEL TANK
FUEL FILTER
PIPE CLAMP
TANK HOUSING
CLUTCH DRUM
CIRCLIP 35
BEARING 6202-2RS
86 MIC36.1101.0004
87 MIC36.1108.0001
88 MIGB/T894.1 15
89 MIC45.6808.0001
90 MIC45.6808.0002
91 MIGB/T2671.2
M6X25
92 MIGB/T893.1 45
93 MIC36.1101.0013
94 MIC36.1101.0014
95 MIC36.1101.0015
96 MIC36.1101.0016
PLASTIC PLATE
CLUTCH DRUM HOUS-
ING
CIRCLIP 15
AV RUBBER
CLAMP
SCREW M6X25
CIRCLIP 45
INSULATION
INSULATION A
INSULATION B
INSULATION C
38
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
Original Instructions Version November 17
360UX/460UVX_1011171
39
360UX, 460UVX Premium Brushcutter
460UVX Parts - Shaft Assembly
7
8
5
6
3
4
ID PART NUMBER
1 MIC36.1100.0100
DESCRIPTION
SHAFT ASSEMBLY
MIC36.1111.0101
MIC36.1111.0102
VIBRATION COVER
SIDE COVER
9
MIC36.1111.0103
MIC36.1111.0104
MIC36.1111.0105
MIGB/T6564
ST4.8X12
MIGB/T6564
ST4.8X19
UPPER COVER
HARNESS PLATE
SUPPORT SEAT
SCREW ST4.8X12
SCREW ST4.8X19
10 MIC43.2111.0306
AV SPRING
11 MIC43.2111.0307
SLEEVE
12 MIC43.2111.0308
SLEEVE
13 MIC43.2111.0310
CLAMP
14 MIGB/T2671.2
M5X16
SCREW M5X16
15 MIGB/T41 M8 NUT M8
16 MIC36.1111.0106
CABLE CLAMP
17 MIGB/T96.1 M5 WASHER M5
18 MIC36.1111.0201
UPPER CLAMP
19 MIC36.1111.0202
LOWER CLAMP
20 MIC27.6111.0205
LOCK KNOB
SCREW M8X60 21 MIGB/T5782
M8X60
22 MIGB/T96.1 M8 PLATE WASHER M8
23 MIC43.2111.0001
HANDLE TUBING
24 MIC43.2111.0201
GRIP
25 MIC43.2111.0202
LEFT HANDLE CLAMP
26 MIGB/T2671.2
M5X45
SCREW M5X45
27 MIGB/T56 M5 NUT M5
28 MIC24.0113.0101
UPPER GUARD
40
29 MIC24.0113.0105
LOWER GUARD
30 MIC24.0113.0104
CUTTING BLADE
31 MIGB/T6564
ST4.2X13
SCREW ST4.2X13
32 MIC43.2113.0309
SCREW ST4.8X19
33 MIC43.2113.0305
GUARD CLAMP
34 MIC43.2113.0307
LOCK SCREW
35 MIGB/T2671.2
M6X12
SCREW M6X12
36 MIGB/T2671.2
M6X25
SCREW M6X25
37 MIC48.B116.0000
GEAR CASE ASSEMBLY
37-1 MIGB/T893.1 28 CIRCLIP 28
37-2 MIGB/T894.1 12
37-3 MIGB/T276 6001-
2Z
CIRCLIP 12
BEARING 6001-2Z
37-4 MIC48.B116.0002
PINION GEAR
37-5 MIGB/T5781 M6X8 SCREW M6X8
37-7 MIGB/T276 6000-
2Z
BEARING 6000-2Z
37-8 MIC43.B116.0004
GEAR
37-9 MIC43.B116.0003
GEAR SHAFT
37-10 MIGB/T276 6002-
2RSP5
BEARING 6002-2RS
37-11 MIGB/T893.1 32 CIRCLIP 32
37-12 MIC43.B116.0006
HOLDER A
37-13 MIC43.B116.0005
HOLDER B
37-14 MIC43.B116.0007
NUT PROTECTOR
37-15 MIGB/T6177.2
M10X1.25
FLANGE NUT
M10X1.25
38 MI TBC NYLON HEAD AS-
SEMBLY
39 MIC43.1100.0001
BLADE
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
460UVX Parts - Shaft Assembly
40 MIC36.1111.0300
THROTTLE CONTROL
ASSEMBLY
40-1 MIC43.1111.0700
SWITCH
40-3 MIC36.2111.0107
SPRING
40-4 MIC43.2111.0106
LOCK TRIGGER
40-6 MI01.01.3121
SCREW ST4X14
40-7 MIGB/T2671.2
M5X35
SCREW M5X35
40-8 MIGB/T97.1 M5
40-9 MIGB/T845
ST3.5X9.5
WASHER M5
SCREW ST 3.5X9.5
40-10 MIC43.2111.0105
TRIGGER SPRING
40-11 MIC43.2111.0104
ROD
40-12 MIC43.2111.0103
TRIGGER
40-13 MIC36.1111.0302
WIRE ASSEMBLY
40-14 MIC36.1111.0301
THROTTLE CABLE
ASSEMBLY
41
360UX, 460UVX Premium Brushcutter
EC DECLARATION OF CONFORMITY
The undersigned, as authorised by: Mitox Garden Machinery
Declares that the following equipment manufactured by Mitox conforms to the Directive: -
2000/14/EC of the European Parliament and of the council on the approximation of the laws of the Member
States relating to the noise emission in the environment by equipment for use outdoors.
Equipment Category – Powered Brushcutters and Grass Trimmers
Product Name/Model: Mitox 360UX
Type/Serial No.: As per rating label on machine
Cutting Width: 430mm (Grass Trimmer) / 255mm(Brushcutter)
Net installed power: 36.3 cm3 / 1.6 kW
The technical documentation is kept by: Stewart Anderson, Rochford Garden Machinery Ltd., Murray
Way, Wincanton Business Park, Somerset, BA9 9RS
The conformity assessment procedure followed was in according with annex EN ISO 11806-1:2011 of the Directive.
Notified Body: Interket Testing Services Shanghai, Building No. 86, 1198 Qinzhou Road (North), Shanghai 200233, China
Measured Sound Power Level: 97 dB
Guaranteed Sound Power Level: 110 dB
A copy of this certificate has been submitted to the European Commission and to EU Member
State United Kingdom
Place of Declaration: China
Date:16/11/2017
Signed by: S. Anderson
Position in Company: Managing Director
Name and address of Authorised representative: Rochford Garden Machinery Ltd., Murray Way,
Wincanton Business Park, Somerset, BA9 9RS
42
Original Instructions Version November 17
360UX/460UVX_1011171
360UX, 460UVX Premium Brushcutter
EC DECLARATION OF CONFORMITY
The undersigned, as authorised by: Mitox Garden Machinery
Declares that the following equipment manufactured by Mitox conforms to the Directive: -
2000/14/EC of the European Parliament and of the council on the approximation of the laws of the Member
States relating to the noise emission in the environment by equipment for use outdoors.
Equipment Category – Powered Brushcutters and Grass Trimmers
Product Name/Model: Mitox 460UVX
Type/Serial No.: As per rating label on machine
Cutting Width: 430mm (Grass Trimmer) / 255mm(Brushcutter)
Net installed power: 46.5 cm3 / 1.95 kW
The technical documentation is kept by: Stewart Anderson, Rochford Garden Machinery Ltd., Murray
Way, Wincanton Business Park, Somerset, BA9 9RS
The conformity assessment procedure followed was in according with annex EN ISO 11806-1:2011 of the Directive.
Notified Body: Interket Testing Services Shanghai, Building No. 86, 1198 Qinzhou Road (North), Shanghai 200233, China
Measured Sound Power Level: 98 dB
Guaranteed Sound Power Level: 112 dB
A copy of this certificate has been submitted to the European Commission and to EU Member
State United Kingdom
Place of Declaration: China
Date:16/11/2017
Signed by: S. Anderson
Position in Company: Managing Director
Name and address of Authorised representative: Rochford Garden Machinery Ltd., Murray Way,
Wincanton Business Park, Somerset, BA9 9RS
Original Instructions Version November 17
360UX/460UVX_1011171
43
360UX, 460UVX Premium Brushcutter
CONDITIONS OF WARRANTY
The manufacturer warrants the product against faulty materials and workmanship for a standard 1 year period and thereafter for the set period specific to each range from the date of purchase. Warranty does not extend to failure due to fair wear and tear.
SP
SELECT
- 1 Year
- 3 Years (Subject to yearly servicing)
PREMIUM - 5 Years (Subject to yearly servicing)
PRO - 5 Years Domestic / 3 Years Commercial (Subject to yearly servicing)
(Extended warranty is subject to online registration and yearly servicing)
SP, SELECT and PREMIUM ranges used for commercial purposes have a warranty period of 3 months from the date of purchase.
The manufacturer undertakes to replace any spare parts that are classified as defective by an appointed Mitox service dealer. The manufacturer will not accept liability for the replacement of the machine, either partially or wholly, and /or consequential damages and /or interest charges either directly or indirectly.
Warranty does not cover failure due to:
Insufficient maintenance.
Incorrect fuel mixture and stale fuel.
Abnormal use or accidental damage.
Incorrect assembly, adjustment or operation of the product.
Spare parts that are subject to wear e.g. bag, blades, bearings, cables, guards, deflectors, spark plugs, air filters etc.
Neither does warranty extend to:
Freight and packing costs.
Use of non-genuine spare parts i.e. those from another manufacturer.
Use of the machine for any other purpose than that for which it was designed.
Use and maintenance of the machine in a manner not described in the owner’s manual.
As part of our policy of continuous product improvement, we reserve the right to alter or amend this specification without notice. As a result, the product may differ from the information contained herein but any alteration will only be implemented without notice if it is classified as an improvement to the above specification.
READ THE MANUAL CAREFULLY BEFORE OPERATING THE MACHINE
When ordering spare parts, please quote the part number, this can be found in the parts list included in this manual.
Retain your proof of purchase, without which no warranty can be offered.
Mitox Garden Machinery, Wincanton Business Park, Wincanton, Somerset, BA9 9RS
44
Original Instructions Version November 17
360UX/460UVX_1011171
Advertisement
