Pioneer XV-LX03 (LX03) Owner Manual


Add to my manuals
88 Pages

advertisement

Pioneer XV-LX03 (LX03) Owner Manual | Manualzz
LX03_En.book
1 ページ
2008年6月24日
DVD/CD Receiver
XV-LX03
Speaker System
SSP-LX03
DVD 5.1 ch Surround System
火曜日
午後6時1分
LX03_En.book
2 ページ
2008年6月24日
火曜日
午後6時1分
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
D3-4-2-1-1_En-A
WARNING
This equipment is not waterproof. To prevent a fire
or shock hazard, do not place any container filled
with liquid near this equipment (such as a vase or
flower pot) or expose it to dripping, splashing, rain
D3-4-2-1-3_B_En
or moisture.
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
D3-4-2-1-4_A_En
or 120 V) written on the rear panel.
WARNING
To prevent a fire hazard, do not place any naked
flame sources (such as a lighted candle) on the
D3-4-2-1-7a_A_En
equipment.
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat
radiation (at least 10 cm at top, 10 cm at rear, and
10 cm at each side).
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left
unused for a long period of time (for example, when
D3-4-2-2-1a_A_En
on vacation).
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from
the AC outlet to shut down all power. Therefore,
make sure the unit has been installed so that the
power cord can be easily unplugged from the AC
outlet in case of an accident. To avoid fire hazard,
the power cord should also be unplugged from the
AC outlet when left unused for a long period of time
D3-4-2-2-2a_A_En
(for example, when on vacation).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the
product, and to protect it from overheating. To
prevent fire hazard, the openings should never be
blocked or covered with items (such as newspapers,
table-cloths, curtains) or by operating the
D3-4-2-1-7b_A_En
equipment on thick carpet or a bed.
Operating Environment
Operating environment temperature and humidity:
+5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
D3-4-2-1-7c_A_En
strong artificial light)
This product complies with the Low Voltage Directive
2006/95/EC and EMC Directive 2004/108/EC.
D3-4-2-1-9a_A_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which
requires repair will be charged for even during the
K041_En
warranty period.
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement. S002_En
LX03_En.book
3 ページ
2008年6月24日
火曜日
午後6時1分
Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified
service personnel.
IMPORTANT: THE MOULDED PLUG
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the
fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug
must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.
If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of
safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Blue : Neutral Brown : Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows ;
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
D3-4-2-1-2-2_B_En
CAUTION
This product is a class 1 laser product, but this
product contains a laser diode higher than Class 1.
To ensure continued safety, do not remove any covers
or attempt to gain access to the inside of the product.
Refer all servicing to qualified personnel.
The following caution label appears on your unit.
Location: inside of the unit
CLASS 1
LASER PRODUCT
D3-4-2-1-8_B_En
Information for users on collection and disposal of old equipment and used batteries
Symbol for
equipment
These symbols on the products, packaging, and/or accompanying documents mean that
used electrical and electronic products and batteries should not be mixed with general
household waste.
For proper treatment, recovery and recycling of old products and used batteries, please
take them to applicable collection points in accordance with your national legislation.
Symbol examples
for batteries
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please
contact your local municipality, your waste disposal service or the point of sale where you
purchased the items.
These symbols are only valid in the European Union.
Pb
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and ask
for the correct method of disposal.
K058_B_En
LX03_En.book
4 ページ
2008年6月24日
火曜日
午後6時1分
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model
properly. After you have finished reading the instructions, put them in a safe place for future reference.
Contents
What’s in the box. . . . . . . . . . . . . . . . . . . . .6
01 Speaker Setup Guide
Safety precautions when setting up . . . . . . .7
Home theater sound setup . . . . . . . . . . . . .7
Standard surround setup . . . . . . . . . . . . .7
Front surround setup. . . . . . . . . . . . . . . . .7
Preparing the speakers . . . . . . . . . . . . . . . .8
Using the supplied speaker stands . . . . . . .9
Wall mounting the speakers . . . . . . . . . . .10
Before mounting . . . . . . . . . . . . . . . . . . .10
Additional notes on speaker placement . . .10
02 Connecting up
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . .11
Basic connections . . . . . . . . . . . . . . . . . . .12
03 Controls and displays
Front panel . . . . . . . . . . . . . . . . . . . . . . . .16
Display . . . . . . . . . . . . . . . . . . . . . . . . . .17
Remote control . . . . . . . . . . . . . . . . . . . . .19
Putting the batteries in
the remote control. . . . . . . . . . . . . . . . . .21
Using the remote control. . . . . . . . . . . . .21
04 Getting started
Using the Auto MCACC setup for optimal
surround sound . . . . . . . . . . . . . . . . . . . . .22
Using the on-screen displays . . . . . . . . . . .23
Playing discs . . . . . . . . . . . . . . . . . . . . . . .24
Basic playback controls . . . . . . . . . . . . .25
Resume and Last Memory. . . . . . . . . . . .25
DVD-Video disc menus . . . . . . . . . . . . . .26
Video CD/Super VCD PBC menus . . . . . .26
05 Listening to your system
Auto listening mode . . . . . . . . . . . . . . . . .27
Listening in surround sound . . . . . . . . . . .27
Dolby Pro Logic II Music settings . . . . . .27
Using Advanced Surround. . . . . . . . . . . . .28
Using Front Stage Surround Advance . . . .28
Listening in stereo . . . . . . . . . . . . . . . . . . .29
Listening with headphones . . . . . . . . . . . .29
Using the Sound Retriever . . . . . . . . . . . . .29
Listening with Acoustic Calibration EQ . . .29
4
En
Enhancing dialogue . . . . . . . . . . . . . . . . . 30
Using Midnight and
Quiet listening modes . . . . . . . . . . . . . . . . 30
Adjusting the bass and treble . . . . . . . . . . 30
Boosting the bass level . . . . . . . . . . . . . . . 30
Adjusting sound delay. . . . . . . . . . . . . . . . 31
06 Disc playback features
Scanning discs . . . . . . . . . . . . . . . . . . . . . 32
Playing in slow motion . . . . . . . . . . . . . . . 32
Frame advance/frame reverse . . . . . . . . . . 32
Playing a JPEG slideshow . . . . . . . . . . . . . 33
Browsing DVD or Video CD/Super VCD
discs with the Disc Navigator . . . . . . . . . . 33
Browsing Windows Media™ Audio (WMA),
MP3, MPEG-4 AAC, DivX video/WMV and
JPEG files with the Disc Navigator . . . . . . 34
Using playlists. . . . . . . . . . . . . . . . . . . . . . 35
Programming playlists . . . . . . . . . . . . . . 35
Listening to playlists . . . . . . . . . . . . . . . . 35
Clearing files from a playlist . . . . . . . . . . 35
Looping a section of a disc . . . . . . . . . . . . 35
Using repeat play . . . . . . . . . . . . . . . . . . . 36
Using random play . . . . . . . . . . . . . . . . . . 36
Creating a program list . . . . . . . . . . . . . . . 37
Other functions available from
the program menu . . . . . . . . . . . . . . . . . 37
Searching a disc . . . . . . . . . . . . . . . . . . . . 38
Switching subtitles . . . . . . . . . . . . . . . . . . 38
Switching language/audio channels . . . . . 38
Zooming the screen . . . . . . . . . . . . . . . . . 39
Switching camera angles . . . . . . . . . . . . . 39
Displaying disc information. . . . . . . . . . . . 39
07 iPod/USB playback
Connecting an iPod. . . . . . . . . . . . . . . . . . 40
Connecting your iPod to this unit . . . . . . 40
iPod playback . . . . . . . . . . . . . . . . . . . . . 40
Using the USB interface . . . . . . . . . . . . . . 42
Basic playback controls . . . . . . . . . . . . . 43
Scanning files. . . . . . . . . . . . . . . . . . . . . 43
Playing a JPEG slideshow . . . . . . . . . . . . 43
Browsing files with the Navigator . . . . . . 44
LX03_En.book
5 ページ
2008年6月24日
火曜日
08 Listening to the radio
13 HDMI Control
45
45
45
46
46
46
47
47
47
09 Surround sound settings
10 Video Adjust menu
11 Initial Settings menu
53
53
54
55
55
55
About DivX® VOD content . . . . . . . . . . . 56
12 Other connections
58
58
59
59
59
60
60
61
61
62
62
63
64
64
64
Español
Using this unit for TV audio . . . . . . . . . . .
Audio input settings from the TVs
(TV Input) . . . . . . . . . . . . . . . . . . . . . . . .
Connecting auxiliary components . . . . . .
Connecting for digital audio. . . . . . . . . .
Connecting an analog audio
component. . . . . . . . . . . . . . . . . . . . . . .
Using the SCART AV connector . . . . . . . .
Line Output setting . . . . . . . . . . . . . . . .
Listening to an external audio source. . . .
Connecting external antennas . . . . . . . . .
About control out connections . . . . . . . . .
Connecting using HDMI . . . . . . . . . . . . .
Switching the HDMI audio setting . . . . .
Setting the Auto Delay . . . . . . . . . . . . . .
Resetting the HDMI connection. . . . . . .
About HDMI . . . . . . . . . . . . . . . . . . . . .
Nederlands
Using the Initial Settings menu . . . . . . . .
Video Output settings . . . . . . . . . . . . . .
Language settings . . . . . . . . . . . . . . . . .
Display settings . . . . . . . . . . . . . . . . . . .
Options settings . . . . . . . . . . . . . . . . . .
Parental Lock. . . . . . . . . . . . . . . . . . . . .
Italiano
Video Adjust menu. . . . . . . . . . . . . . . . . . 52
Optional system settings . . . . . . . . . . . . . . 69
Setting the sleep timer . . . . . . . . . . . . . . 69
Dimming the display . . . . . . . . . . . . . . . . 69
Changing the display mode. . . . . . . . . . . 70
Key lock setting. . . . . . . . . . . . . . . . . . . . 70
TV system setting . . . . . . . . . . . . . . . . . . 70
Setting up the remote to control your TV . . 71
TV Preset code list. . . . . . . . . . . . . . . . . . 71
Surround sound formats . . . . . . . . . . . . . . 72
Dolby. . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Dolby Digital . . . . . . . . . . . . . . . . . . . . . . 72
Dolby Pro Logic II and Dolby Surround . . 72
DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
DTS Digital Surround . . . . . . . . . . . . . . . 72
Disc/content format playback
compatibility . . . . . . . . . . . . . . . . . . . . . . . 73
CD-R/-RW compatibility . . . . . . . . . . . . . 73
DVD+R/DVD+RW compatibility . . . . . . . 74
DVD-R/-RW compatibility . . . . . . . . . . . . 74
Compressed audio compatibility . . . . . . . 74
About MPEG-4 AAC. . . . . . . . . . . . . . . . . 74
WMA (Windows Media™ Audio)
compatibility . . . . . . . . . . . . . . . . . . . . . . 74
About DivX . . . . . . . . . . . . . . . . . . . . . . . 75
About WMV. . . . . . . . . . . . . . . . . . . . . . . 75
JPEG file compatibility . . . . . . . . . . . . . . 76
PC-created disc compatibility . . . . . . . . . 76
Using and taking care of discs . . . . . . . . . 76
DVD Video regions . . . . . . . . . . . . . . . . . 76
Installation and maintenance . . . . . . . . . . 77
Hints on installation . . . . . . . . . . . . . . . . 77
Cleaning the pickup lens. . . . . . . . . . . . . 77
Problems with condensation. . . . . . . . . . 77
Moving the system unit . . . . . . . . . . . . . . 77
Screen sizes and disc formats . . . . . . . . . . 77
Widescreen TV users. . . . . . . . . . . . . . . . 77
Standard TV users . . . . . . . . . . . . . . . . . . 78
Using your own speaker cables . . . . . . . . . 78
Français
48
48
49
49
50
50
51
51
51
14 Additional information
Deutsch
Using the Sound Setup menu . . . . . . . . .
Effective Sound (for optimum sound) . .
Channel level setting . . . . . . . . . . . . . . .
Speaker distance setting . . . . . . . . . . . .
Dynamic Range Control. . . . . . . . . . . . .
Virtual Surround Back . . . . . . . . . . . . . .
LFE Attenuate . . . . . . . . . . . . . . . . . . . .
DTS CD setting . . . . . . . . . . . . . . . . . . .
Dual mono setting . . . . . . . . . . . . . . . . .
Making the HDMI Control connections . . . 65
Setting the HDMI options . . . . . . . . . . . . . 67
Setting the HDMI Control mode . . . . . . . 67
Before using synchronization . . . . . . . . . . 67
Synchronized amp mode . . . . . . . . . . . . . . 68
Synchronized amp mode operations . . . . 68
Canceling synchronized amp mode . . . . 68
English
Listening to the radio . . . . . . . . . . . . . . . .
Improving poor FM reception. . . . . . . . .
Improving poor AM sound . . . . . . . . . . .
Changing the noise cut mode . . . . . . . .
Memorizing stations . . . . . . . . . . . . . . .
Listening to station presets . . . . . . . . . .
Using RDS . . . . . . . . . . . . . . . . . . . . . . . .
Displaying RDS information . . . . . . . . .
Searching for RDS programs. . . . . . . . .
午後6時1分
5
En
IntroductionTOC.fm
6 ページ
2008年7月1日
火曜日
Troubleshooting. . . . . . . . . . . . . . . . . . . . .79
General . . . . . . . . . . . . . . . . . . . . . . . . . .79
DVD/CD/Video CD player. . . . . . . . . . . . .80
Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . .81
USB connection . . . . . . . . . . . . . . . . . . .82
HDMI connection . . . . . . . . . . . . . . . . . .82
Front panel display messages . . . . . . . . .83
午後1時27分
Resetting the system. . . . . . . . . . . . . . . . . 84
Using the language code list. . . . . . . . . . . 84
Language code list . . . . . . . . . . . . . . . . . . 85
Country/Area code list. . . . . . . . . . . . . . . . 85
Specifications . . . . . . . . . . . . . . . . . . . . . . 86
What’s in the box
Please confirm that the following items are all supplied.
DVD/CD receiver box:
Speakers box:
• Remote control
• Speakers (front x2, center x2, surround x2)
• AA/R6 dry cell batteries (to confirm system
operation) x2
• Subwoofer
• Video cable (yellow plugs)
• Brackets x2
• AM loop antenna
• Screws (for brackets) x4
• FM antenna
• Speaker stands x2
• Microphone (for Auto MCACC setup)
• Non-skid pads (for satellite speakers) x24
• Power cords x2
• Non-skid pads (for subwoofer) x4
• Speaker cable adaptors x5
• Non-skid pads (for speaker stands) x8
• Cleaning cloth*
• Spiral wrap x2
• Speaker cables x7
• Warranty card
• Setup Guide
• These operating instructions
*When cleaning the cabinet, use the provided cleaning cloth.
Do not allow alcohol, thinner, benzene, or insecticides to come into contact with the surface, since
finish discoloration may occur.
6
En
LX03_En.book
7 ページ
2008年6月24日
火曜日
午後6時1分
Speaker Setup Guide
01
English
Chapter 1
Speaker Setup Guide
If the speakers are to be used in a stacked
configuration, always use the provided
brackets to secure them together (page 8).
This setup is ideal when rear surround speaker
placement isn’t possible or you want to avoid
running long speaker cables in your listening
area. The surround left and right speakers
should be about 1.5 m apart.
Surround
left
Front
right
Front
left
Center
Depending on the size and characteristics of
your room, you can place your speakers in one
of two ways using this system.
Listening position
Front
right
SR
SL
C
Español
This is a standard multichannel surround sound
speaker setup for optimal 5.1 channel home
theater sound. The front left and right speakers
should be about 1.8 m to 2.7 m apart.
Nederlands
*When center speakers are placed in the center.
FR
FL
Standard surround setup
Italiano
Subwoofer
Home theater sound setup
Front
left
Surround
right
Center
Français
When assembling the speakers, lay them down
flat on their side to avoid accidents or injury.
Make sure to use a stable surface when
assembling, setting up, and placing the
speakers.
Front surround setup
Deutsch
Safety precautions when
setting up
Center
Subwoofer
Surround
left
Listening position
Surround
right
*When center speakers are placed in the center.
FR FR
FL
C
7
En
LX03_En.book
01
8 ページ
2008年6月24日
火曜日
午後6時1分
Speaker Setup Guide
Preparing the speakers
1 Attach the non-skid pads to the base of
each speaker (as shown).
Use the adhesive side of the pads to attach
them to the base (flat surface) of each speaker.
As shown in the illustration, stack the
speakers. Align the brackets with the screw
holes on the back of the two speakers, and use
the two screws to fix in place.
Standard surround setup:
Left
Non-skid pads
(for satellite
speakers)
Right
White
Front
speaker
Green
Center
speaker Green
Red
Front
speaker
Front
speaker
Center
speaker
Surround
speaker
Bracket
Center
speaker
Non-skid pads
(for subwoofer)
Screw
Subwoofer
2 (When mounting center speakers to right
and left) Stack the speakers and fix with the
bracket.
Each speaker is provided with a color-coded
indicator on the label on the rear side to assist
identification. Refer to the color indicators and
install the speakers correctly.
Color indicator
8
En
LX03_En.book
9 ページ
2008年6月24日
火曜日
午後6時1分
Speaker Setup Guide
01
Front surround setup:
Right
Blue
Surround Grey
speaker
Center
speaker
When setting up the front surround, the
supplied accessory speaker stand can be used.
Apply the non-skid pads (for speaker stand) to
the four corners of the speaker stand and set
the speakers on the stand.
Green
Non-skid pads
(for speaker stands)
Surround
speaker
Speaker stand
Français
Bracket
Center
speaker
Deutsch
Green
Using the supplied speaker
stands
English
Left
Screw
Nederlands
Español
3 Connect the speaker system.
Refer to Connecting up on page 11 to connect
the speakers properly. After connecting
everything, place the speakers as shown in the
diagram above for optimal surround sound.
After placing the speakers, run the Auto
MCACC setup (page 22) to complete your
surround sound setup.
Italiano
Caution
• Do not attempt to carry the speakers when
they are connected with the bracket. Doing
so may cause damage to the bracket or
worsen damage to the bracket and
speakers in the event they are dropped.
9
En
LX03_En.book
01
10 ページ
2008年6月24日
火曜日
Speaker Setup Guide
Wall mounting the speakers
The front, center and surround speakers have a
mounting hole which can be used to mount the
speaker on the wall.
Before mounting
• Remember that the speaker system is
heavy and that its weight could cause the
screws to work loose, or the wall material to
fail to support it, resulting in the speaker
falling. Make sure that the wall you intend
to mount the speakers on is strong enough
to support them. Do not mount on plywood
or soft surface walls.
• Mounting screws are not supplied. Use
screws suitable for the wall material and
support the weight of the speaker.
Caution
• If you are unsure of the qualities and
strength of the wall, consult a professional
for advice.
• Pioneer is not responsible for any
accidents or damage that result from
improper installation.
5 mm
10 mm
Mounting screw
(not supplied)
6 mm to 8 mm
10
En
午後6時1分
Additional notes on speaker
placement
• Install the main front left and right
speakers at an equal distance from the TV.
• When using the Standard surround setup,
install the surround speakers slightly
above ear level for optimum effect.
Precautions:
• When installing the center speaker on top
of the TV, be sure to secure it with tape or
some other suitable means. Otherwise, the
speaker may fall from the TV due to
external shocks such as earthquakes,
endangering those nearby or damaging
the speaker.
• The front, center and surround speakers
supplied with this system are magnetically
shielded. However, depending on the
installation location, color distortion may
occur if the speaker is installed extremely
close to the screen of a television set. If this
case happens, turn the power switch of the
television set OFF, and turn it ON after 15
min. to 30 min. If the problem persists,
place the speaker system away from the
television set.
• The subwoofer is not magnetically shielded
and so should not be placed near a TV or
monitor. Magnetic storage media (such as
floppy discs and tape or video cassettes)
should also not be kept close to the
subwoofer.
• Do not attach the subwoofer to the wall or
ceiling. They may fall off and cause injury.
LX03_En.book
11 ページ
2008年6月24日
火曜日
午後6時1分
Connecting up
02
English
Chapter 2
Connecting up
1
2
3
4
5
6
7
8
9
10
11
12 13
Deutsch
Rear panel
ANALOG
IN
R
FRONT 4
OUT
CONTROL
CENTER
L
1
L
OPTICAL
4
R
AV CONNECTOR
VIDEO OUT
L
ANALOG 2
AUDIO IN
R
AUDIO OUT
1
R
SURROUND 8
L
SUB WOOFER 4
SPEAKERS
AC IN – Power inlet
4 SPEAKERS terminals
Match the colors of the speaker cables to their
respective connectors.
6 AUDIO IN1 (ANALOG) jacks
Handle sound from an external component by
using stereo audio cable. To listen to analog
audio, change the input to Analog 1 RCA.
7
HDMI
OUT
IN 2
ANTENNA
IN 1
9 HDMI IN1/2 connectors
Use high-quality audio/video connection with
compatible HDMI devices.
To select this input, choose HDMI 1 or HDMI 2.
10 AV CONNECTOR
Audio/video output SCART-type AV connector
for connecting to a TV or other equipment with
a SCART connector.
To select this input, choose Analog 2 SCART.
11 DIGITAL IN1/2 (OPTICAL) jacks
To listen to optical digital audio, change the
input to Digital 1 OPT or Digital 2 OPT.
12 AM LOOP antenna terminal
Español
5 DIGITAL IN3 (COAX) jack
To listen to coaxial digital audio, change the
input to Digital 3 COAX.
DIGITAL IN
Nederlands
3 CONTROL IN/OUT jacks
Use to connect other Pioneer components so
that you can control all your equipment from a
single IR remote sensor.
3
COAX
DIGITAL IN
Italiano
2 AUDIO OUT (ANALOG) jacks
Connect to the other audio component
1 AM
LOOP
FM
2 UNBAL
75
AC IN
Français
ANALOG
13 FM antenna socket
VIDEO OUT jack
Use to connect a TV.
8 HDMI OUT connector
Connect to a television that has an HDMI
terminal.
11
En
LX03_En.book
02
12 ページ
2008年6月24日
火曜日
午後6時1分
Connecting up
Basic connections
1
FM antenna
AM loop antenna
To video input
4
TV
2
ANALOG
IN
ANALOG
R
FRONT 4
OUT
CONTROL
CENTER
L
1
L
OPTICAL
4
R
AV CONNECTOR
VIDEO OUT
L
1 AM
LOOP
ANALOG 2
AUDIO IN
FM
2 UNBAL
75
AC IN
R
AUDIO OUT
R
SURROUND 8
L
SUB WOOFER 4
3
COAX
DIGITAL IN
SPEAKERS
DIGITAL IN
HDMI
OUT
IN 2
ANTENNA
IN 1
3
Front left
(White)
Center
(Green)
Surround left
(Blue)
Front right
(Red)
Subwoofer
(Purple)
Surround right
(Grey)
Listening position
Important
• When connecting this system or changing
connections, be sure to switch power off
and disconnect the power cord from the
wall socket.
After completing all connections, connect
the power cords to the wall socket.
12
En
WARNING
• Pioneer bears no responsibility for
accidents resulting from faulty assembly or
installation, insufficient mounting strength
of walls, mounting fixtures (or other
building fixtures), misuse or natural
disasters.
LX03_En.book
13 ページ
2008年6月24日
火曜日
午後6時1分
Connecting up
1
02
Assemble the AM loop antenna.
fig. c
fig. b
b. Clip the loop onto the stand.
It is recommended that you determine the
reception strength before securing the
stand with the screws.
Connect the AM and FM antennas1.
a. Connect one wire of the AM loop antenna
to each AM antenna terminal2.
Color-coded connector
(Connect to rear panel)
• Since there is only one terminal to connect
the two center speakers, you will need to
use the supplied Y-cable for the connection.
• Twist and pull off the protective shields on
each wire.
2
3
1
• Connect the wires to the speaker. Each
speaker in the illustration can be identified
by means of the color-coded indicator
provided on the rear-surface label.
Español
b. Push the FM antenna3 plug onto the center
pin of the FM antenna socket.
Nederlands
For each terminal, press down on the tab to
open; insert the wire, then release to
secure.
Color-coded wire
(Connect to speaker)
Italiano
2
• Two purple cables are provided for the
subwoofer, one 4 meters and the other 10
meters in length. Use the appropriate cord
depending on the length needed for the
installation location.
Français
c. If you want to fix to a wall or other surface,
perform step b after first securing the
stand with screws.
• The front and surround speaker cables
have a color-coded connector at one end
and two bare wires at the other end.
Deutsch
a. Bend the stand in the direction indicated by
the arrow.
Connect each speaker.
• You may purchase and use your own
speaker cables if desired. For details, see
Using your own speaker cables on page 78.
English
fig. a
3
Note
1 • Keep antenna cables away from the receiver and other cables.
• If reception with the supplied antenna is poor, see Improving poor FM reception and Improving poor AM sound on
page 45 or Connecting external antennas on page 61.
• Do not attach any antenna other than the provided loop antenna, or an external antenna as described on page 61.
2 • Don’t let it come into contact with metal objects and avoid placing near computers, television sets or other electrical
appliances.
• If radio reception is poor, you may be able improve it by re-inserting each antenna wire into the opposite terminal.
• For best reception, do not untwist the AM loop antenna wires or wrap them around the loop antenna.
3 To ensure optimum reception, make sure the FM antenna is fully extended and not coiled or hanging at the rear of
the unit.
13
En
LX03_En.book
02
14 ページ
2008年6月24日
火曜日
午後6時1分
Connecting up
Match the color-coded wire with the color
indicator on the label, then insert the colorcoded wire into the red (+) side and the
other wire into the black (–) side.
Black (–)
Red (+)
Color-coded wire
• Fasten the cables together with the spiral
wrap.
Hold multiple cables together and place
the wrap over the cables from the end.
Wrap the spiral wrap with the cables in the
center.
The spiral wrap may be cut at a desired
length.
• When connecting the center speakers,
connect the Y-cable dual end to the two
center speakers in the same way.
Caution
• These speaker terminals carry
HAZARDOUS LIVE voltage. To prevent
the risk of electric shock when connecting
or disconnecting the speaker cables,
disconnect the power cord before touching
any uninsulated parts.
Y-cable
To receiver
• Connect the other end to the color-coded
speaker terminals on the rear of the
receiver. Make sure to insert completely.
The small lug at the wire-end of the speaker
plug should face up or down depending on
whether it’s being plugged into one of the
upper or lower speaker terminals. Please
make sure to connect correctly.
Upper terminal
14
En
Lower terminal
• Do not connect any speakers other than
those supplied to this system.
• Do not connect the supplied speakers to
any amplifier other than the one supplied
with this system. Connection to any other
amplifier may result in malfunction or fire.
• After connecting the plugs, pull lightly on
the cables to make sure that the ends of
the cables are securely connected to the
terminals. Poor connections can create
noise and interruptions on the sound.
• If the cable’s wires happen to be pushed
out of the terminals, allowing the wires to
come into contact with each other, it
places an excessive additional load on the
amp. This may cause the amp to stop
functioning, and may even damage the
amp.
LX03_En.book
15 ページ
2008年6月24日
火曜日
午後6時1分
Connecting up
02
• Use the supplied video cable.
5 Connect the other end to the video
output of the receiver.
Connect the power cord.1
• Connect the power cord to AC inlet on the
receiver. Connect the power cord to a wall
socket.
Français
6
Deutsch
• This unit is equipped with copy protection
technology. Do not connect this unit to
your TV via a VCR using AV cables, as the
picture from this unit will not appear
properly on your TV.
English
4 Connect one end to a video input on
your TV.
Italiano
AC IN
Nederlands
To AC outlet
Español
Note
1 • Do not use any power cord other than the one supplied with this system.
• Do not use the supplied power cord for any purpose other than connecting to this system.
15
En
LX03_En.book
03
16 ページ
2008年6月24日
火曜日
午後6時1分
Controls and displays
Chapter 3
Controls and displays
Front panel
INP
11
12
PULL OPEN

STANDBY/ON
HDMI
VOLUME
FUNCTION
iPod DIRECT /USB
OPEN/CLOSE
1
2
3
• Open the front door flap when inserting a
disc or using the front panel connectors.
1  STANDBY/ON
Switches the system on or into standby.
2 HDMI indicator (Red)
Lights when this system is connected to HDMI
(HDCP) compatible component.
Also lights during initialization, after you plug
this unit into an AC outlet.
Disc tray
4  OPEN/CLOSE
Opens/closes the disc tray.
5 PHONES jack
Connect headphones.
6 MCACC jack
Use to connect the supplied microphone for
the Auto MCACC setup (page 22).
16
En
MCACC
HDMI
STANDBY / ON
3
PHONES
4
5
6 7 8
9
10
7 iPod DIRECT/USB terminal
Use to connect your Apple iPod as an audio
source (page 40), or connect a USB audio
device for playback (page 42).
8
IR remote sensor
9 Front panel display
See Display below for details.
10 Motion sensor
When the front panel display is off, if Display
Mode is set to Auto Display, the display will
automatically turn on when movement is
detected by the motion sensor (page 70).
11 Action indicator
Lights when a touch sensor operation is
performed.
LX03_En.book
17 ページ
2008年6月24日
火曜日
午後6時1分
Controls and displays
03
Lightly touch the displayed words or symbols to
operate controls.
/
Starts/pauses playback.
Deutsch
FUNCTION
Selects the source you want to listen to
(Digital 1 to Digital 3, Analog 1, Analog 2,
DVD/CD, iPod, USB, HDMI 1 or HDMI 2).
This system features a motion sensor. Install it
in a location that will able to sense the
movement of people near by.
The motion sensor detects movement in the
left/right and up/down directions within a
distance of 2.5 m and an angle of 40º (20º only
in the upper direction). Walking towards the
unit will reduce the sensing range to 0.7 m.
English
Using the motion sensor
12 Touch sensor
Touch sensor is on top of the unit.
PULL OPEN
REVE
IRTER
DNUO
S
Français

Stops playback.
HDMI
40
VOLUME +/–
Use to adjust the volume.
20
Italiano
2.5
m
40
40
Nederlands
Display
1
2
PGM
RDM
RPT 1
V
6
4
PCM
DTS
BASS MODE TONE V.SB L.OUT
ALC S.RTRV DIALOG MCACC
5
A
B
C
I
7
8
9 10
1 DIRECT
Lights when Direct Sound is selected (i.e.
Effective Sound is off) (page 48).
ADV SURR
Lights when one of the Advanced Surround
listening modes is selected (page 28).
2
F.S.SURR
Lights when one of the Front Stage
Surround Advance listening modes is
selected (page 28).
Listening mode indicators
STEREO
Lights when the Stereo mode is selected or
when a stereo source is being played back
in the Auto listening mode (page 27).
Español
DIRECT STEREO
2DAAC
ADV SURR F.S.SURR 2PL
3
17
En
LX03_En.book
03
18 ページ
2008年6月24日
火曜日
午後6時1分
Controls and displays
3
RDM
Lights during random play (page 36).
Digital format indicators
2D
Lights during playback of a Dolby Digital
source (page 27).
RPT and RPT-1
RPT lights during repeat play. RPT-1 lights
during repeat one-track play (page 36).
2 PLII
Lights during Dolby Pro Logic II decoding
(page 27).
V
Lights when playing a video part of a DVD
disc.
PCM
Lights during playback of PCM signals.

Lights during playback.
DTS
Lights during playback of a DTS source
(page 27).
4
Sound processing indicators
Lights during shuffle play.
Lights during repeat play.
ALC
Lights when listening mode is set to A.L.C.
(page 27).
S.RTRV
Lights when Sound Retriever is active
(page 29).
DIALOG
Lights when Dialogue Enhancement is
active (page 30).
5 MCACC
Lights when Acoustic Calibration EQ is active
(page 29).
Blinks during Auto MCACC Setup (page 22).
En
iPod indicators
TONE
Lights when any of the Midnight, Quiet or
tone controls feature is selected (page 30).
L.OUT
Lights when Line Output is set to Lt/Rt
(page 60).
18
7
BASS MODE
Lights when Bass Mode is active (page 30).
V.SB
Lights when Virtual Surround Back mode
is active (page 50).
6
Lights when playing a multi-angle scene.
PGM
Lights during program play (page 35).
Lights during 1-track repeat play.
8
Character display
9
Tuner indicators
Lights when a broadcast is being received.
Lights when a stereo FM broadcast is being
received in auto stereo mode.
Lights when FM mono reception is
selected.
Lights when in one of the RDS display or
search modes.
A, B, C
Indicate the class of tuner function.
10
Lights when sleep timer is active (page 69).
LX03_En.book
19 ページ
2008年6月24日
火曜日
午後6時1分
Controls and displays
03
STANDBY / ON

1
2
1/2
PLAYLIST
CD
DVD
HDMI
iPod
1
USB
TV
LINE
2
FM/AM
TUNER
3 Function select buttons
Use to select an input source.
3
2
3
4
5
6
7
8
9
CLEAR
0
CH
4 PLAYLIST buttons
Add tracks (during playback), or select a
playlist (while stopped) (page 35).
VOLUME
VOL
7
5 Number buttons
Use to enter a track number or radio station.
8
6 TV CONTROL buttons
These control Pioneer flat screen TVs.
6
INPUT
MUTE

SOUND
TUNE
10
11
ST
RETURN
13
TUNE
MENU
AUDIO
ZOOM
CLASS
SUBTITLE ANGLE
15
14
T.EDIT
17
16
/
/
18
SOUND
SURROUND ADV SURR RETRIEVER
MCACC
iPod
DISPLAY
19
22
20
21
CTRL
9 SETUP
Use to make various system and surround
sound settings (page 48, 63, 69).
23
10 SOUND
Accesses the sound menu to adjust the tone,
bass and treble, etc. (page 27, 29, 30).
Español
12
8 MUTE
Mutes the sound (press again to cancel).
ST
ENTER
TOP
MENU
7 VOLUME +/–
Adjusts the volume.
Nederlands
SETUP
9
Italiano
TV CONTROL
See the section Audio input settings from the
TVs (TV Input) on page 58 for information
regarding the TV button.
Français
1
5
4
2 HOME MENU
Displays (or exits) the on-screen menu for
Initial Settings, Play Mode functions, etc.
Deutsch
3
1  STANDBY/ON
Switches the system on or into standby.
HOME MENU
English
Remote control
11 /// (TUNE +/–, ST +/–), ENTER
Use to select/switch system settings and
modes, and to confirm actions.
Use TUNE +/– to find radio frequencies and
use ST +/– to find preset stations.
19
En
LX03_En.book
03
20 ページ
2008年6月24日
火曜日
Controls and displays
12 TOP MENU
Displays the top menu of a DVD disc in the play
position — this may be the same as pressing
MENU (page 26).
Press to return to the iPod Top menu when
using iPod functions.
13 RETURN
Returns to a previous menu screen.
14 MENU
Press to display a USB menu, or the Navigator
(page 26, 33, 44).
15 DVD controls
AUDIO
Selects audio channel/language (page 38).
SURROUND
Selects a Surround mode (page 27) or
switches to stereo playback (page 29).
ADV SURR
Selects a Pioneer original surround mode
(page 28).
20 SOUND RETRIEVER
Press to restore CD quality sound to
compressed audio sources (page 29).
21 MCACC
Starts the Auto MCACC setup (page 22).
22 iPod controls
CTRL
Switches between the iPod controls and
the receiver controls.
ANGLE
Changes camera angle during DVD multiangle scene playback (page 39).
Changes repeat play setting.
17 Tuner controls
CLASS
Switches between the three banks
(classes) of radio station presets (page 46).
T.EDIT
Memorizes stations for recall (page 46).
18 Playback controls
See Basic playback controls on page 25, Disc
playback features on page 32, iPod playback on
page 40 and Using the USB interface on
page 42 for an explanation of these controls.
En
19 Sound controls
SUBTITLE
Displays/changes the subtitles (page 38).
16 ZOOM
Changes the screen zoom level (page 39).
20
午後6時1分
Changes shuffle play setting.
23 DISPLAY
Displays/changes disc information shown onscreen (page 39) or to display RDS information
(page 47).
Displays song playback information when
using the iPod function.
LX03_En.book
21 ページ
2008年6月24日
火曜日
午後6時1分
Controls and displays
3
Close the cover.
Caution
Italiano
Incorrect use of batteries can result in hazards
such as leakage and bursting. Please observe
the following:
• Make sure that there are no obstacles
between the remote and the remote sensor
on the unit.
• Remote operation may become unreliable
if strong sunlight or fluorescent light is
shining on the unit’s remote sensor.
• Remote controllers for different devices
can interfere with each other. Avoid using
remotes for other equipment located close
to this unit.
• Replace the batteries when you notice a
fall off in the operating range of the remote.
• Use within the operating range in front of
the remote control sensor on the display
unit, as shown.
Français
2 Insert two AA/R6 batteries into the
battery compartment following the
indications (, ) inside the compartment.
Please keep in mind the following when using
the remote control:
Deutsch
1 Open the battery compartment cover
on the back of the remote control.
Using the remote control
English
Putting the batteries in the remote
control
03
PULL OPEN
• Don’t mix new and old batteries together.
• Remove batteries from equipment that
isn’t going to be used for a month or more.
IRTER
DNUO
S
30
30
7m
Español
• Make sure that the plus and minus ends of
each battery match the indications in the
battery compartment.
REVE
HDMI
Nederlands
• Don’t use different kinds of battery
together — although they may look similar,
different batteries may have different
voltages.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country/area.
• Do not use or store batteries in direct
sunlight or other excessively hot place,
such as inside a car or near a heater. This
can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the
life or performance of batteries.
21
En
LX03_En.book
04
22 ページ
2008年6月24日
火曜日
午後6時1分
Getting started
Chapter 4
Getting started
Using the Auto MCACC setup for
optimal surround sound
The Multichannel Acoustic Calibration
(MCACC) system measures the acoustic
characteristics of your listening area, taking
into account ambient noise, and testing for
channel delay and channel level. After you
have set up the microphone provided, the
system uses the information from a series of
test tones to measure reverb, optimizing the
speaker settings and equalization (Acoustic
Calibration EQ) for your particular room.1
1 Connect the microphone to the MCACC
jack on the front panel.
• Open the front panel door to access the
MCACC jack.
iPod DIRECT /USB
OPEN/CLOSE
PHONES
ECT/USB
MCACC
Microphone
Important
• The test tones used for Auto MCACC setup
are loud; however, do not turn the volume
down during setup as this may result in a
sub-optimal setup.
• Make sure the microphone and speakers
are not moved during the MCACC setup.
MCACC
2 Place the microphone at your normal
listening position.
Place it about ear height, and make sure it is
level by using a table or chair.
Make sure there are no obstacles between the
speakers and the microphone.
STANDBY / ON
 If the system isn’t already on,
3
switch it on.
MCACC
4
Press MCACC.
Try to be as quiet as possible after pressing
MCACC. The volume increases automatically
and the system outputs a series of test tones.
• To cancel Auto MCACC setup before it has
finished, press MCACC. The unit will
continue to use the previous settings.
Note
1 You only need to use the Auto MCACC setup once (unless you change the placement of your speakers or your room layout).
22
En
LX03_En.book
23 ページ
2008年6月24日
火曜日
午後6時1分
Getting started
• Be sure to disconnect the microphone
from this unit upon completion of the Auto
MCACC setup.
All the screens are navigated in basically the
same way, using /// to change the
highlighted item and pressing ENTER to select
it.5
Important
• Throughout this manual, ‘Select’ means
use the cursor buttons to highlight an item
on-screen, then press ENTER.
What it does
HOME MENU
Displays/exits the on-screen display.
Changes the highlighted menu item.
RETURN
Selects the highlighted menu item.
Returns to the main menu without
saving changes.
• The button guide at the bottom of every
OSD screen shows you which buttons
you’ll need to use for that screen.
Español
Tip
Nederlands
ENTER
Italiano
Button
Français
When the MCACC setup is complete, the
volume level returns to normal, Complete3
shows in the display, and Acoustic Calibration
EQ is activated.4
Simple and convenient graphic on-screen
displays (OSDs) are used when this system is
connected to a television.
Deutsch
• If you see an Error MIC! or Error Speaker!
message in the display, there may be a
problem with the microphone or the
speaker connections. To try again, press
ENTER2.
Using the on-screen displays
English
• If the ambient noise level is too high,
Noisy! blinks in the display for five
seconds. To exit and check the noise
levels1, press MCACC, or to try again, press
ENTER when Retry shows in the display.
04
Note
1 • If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles
blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air
conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.
• Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off the TV during
Auto MCACC setup.
2 If this doesn’t work, press MCACC, turn off the power, and check the problem indicated by the Error message, then try the
Auto MCACC setup again.
3 If Complete doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.
4 See Listening with Acoustic Calibration EQ on page 29 to switch on/off Acoustic Calibration EQ.
5 The screen saver will appear after five minutes of inactivity.
23
En
LX03_En.book
04
24 ページ
2008年6月24日
火曜日
午後6時1分
Getting started
Playing discs
The basic playback controls for playing DVD,
CD, SACD, Video CD/Super VCD, DivX video/
WMV and MP3/WMA/MPEG-4 AAC discs are
covered here. Further functions are detailed in
chapter 6.
If you loaded a disc containing JPEGs, a
slideshow will start. See Playing a JPEG
slideshow on page 33 for more on this.
• If a disc contains a mixture of DivX video/
WMV and other media file types (MP3, for
example), first select whether to play the
DivX video/WMV files (DivX/WMV) or the
other media file types (MP3/WMA/JPEG/
MPEG-4 AAC) from the on-screen display.
Important
• Please see Disc/content format playback
compatibility on page 73 if you want to play
a DualDisc (DVD/CD hybrid disc).
• Throughout this manual, the term ‘DVD’
means DVD-Video, DVD-Audio and
DVD-R/-RW. If a function is specific to a
particular kind of DVD disc, it is specified.
VOLUME
STANDBY / ON
 If the system isn’t already on,
1
switch it on.
If you’re playing a DVD, disc containing DivX
video/WMV files or Video CD/Super VCD, also
turn on your TV and make sure that it is set to
the correct video input.
OPEN/CLOSE
2
[front panel] Press to load a
disc.
• Open the front panel door to access the 
OPEN/CLOSE button.
Load a disc with the label side facing up, using
the disc tray guide to align the disc (if you’re
loading a double-sided DVD disc, load it with
the side you want to play face down).
3
Start playback.
If you’re playing a DVD or Video CD/Super VCD,
a menu may appear. See DVD-Video disc
menus and Video CD/Super VCD PBC menus on
page 26 to navigate these.
24
En
4
Adjust the volume.
LX03_En.book
25 ページ
2008年6月24日
火曜日
午後6時1分
Getting started
The following table shows the basic controls on
the remote for playing discs.1 You can find
other playback features in chapter 6.
Button
What it does
Stops playback or cancels the
resume function (if the display
shows Resume).
Press to start fast forward scanning.
/
With DVDs and Video CD/Super VCDs, if you
take the disc out of the player after stopping
playback, the last play position is stored in
memory. If the next disc you load is the same
one, the display shows Last Memory and
playback will resume.3 For DVD-Video discs,
the player stores the play position of the last
five discs. When one of these discs is next
loaded, you can resume playback.
Skips to the next track, title or
chapter.
2
3
4
5
6
7
8
9
CLEAR
0
ENTER
Use to enter a title/chapter/track
number. Press ENTER to select.
• If the disc is stopped, playback
starts from the selected title (for
DVD), group (for DVD-Audio) or
track (for CD/SACD/Video CD/Super
VCD).
• If the disc is playing, playback
jumps to the start of the selected
title (VR mode DVD-RW), chapter
(DVD-Video) or track (DVD-Audio*/
SACD/CD/Video CD/Super VCD).
*within the current group
Español
1
Nederlands
Skips to the start of the current
track, title or chapter, then to
previous tracks/titles/chapters.
Italiano
Press to start fast reverse scanning.
/
If the disc tray is not opened, the next time you
start playback the display shows Resume and
playback resumes from the resume point. (If
you want to clear the resume point, press
 (stop) while Resume is displayed.)
Français
Pauses/unpauses a disc.
With the exception of DVD-Audio, SACD and
MP3/WMA/MPEG-4 AAC discs, when you stop
playback of a DVD, CD, or Video CD/Super VCD
or DivX video/WMV discs, Resume is shown in
the display indicating that you can resume
playback again from that point.
Deutsch
Starts/resumes normal playback.
• If the display shows Resume or
Last Memory playback starts from
the resume or last memory point
(see Resume and Last Memory
below).
Resume and Last Memory2
English
Basic playback controls
04
Note
1 You may find with some DVD discs that some playback controls don’t work in certain parts of the disc.
2 The Resume and Last memory functions may not work with some discs.
3 • The Last Memory function doesn’t work with VR format DVD-R/-RW, DVD-Audio or SACD discs.
• If you don’t need the Last Memory function when you stop a disc, you can press  OPEN/CLOSE to stop playback and open
the disc tray.
25
En
LX03_En.book
04
26 ページ
2008年6月24日
火曜日
Getting started
DVD-Video disc menus
Video CD/Super VCD PBC menus
Many DVD-Video and DVD-Audio discs feature
menus from which you can select what you
want to watch. They may also give access to
additional features, such as subtitle and audio
language selection, or special features such as
slideshows. See the disc packaging for details.
Some Video CD/Super VCDs have menus from
which you can choose what you want to watch.
These are PBC (Playback control) menus.
Sometimes DVD-Video and DVD-Audio menus
are displayed automatically when you start
playback; others only appear when you press
MENU or TOP MENU.
Important
• Some DVD-Audio discs feature a ‘bonus
group’. To play this group you first have to
input a password, which you can find on
the disc’s packaging. Use the number
buttons to input the password.
Button
What it does
TOP
MENU
Displays the ‘top menu’ of a DVD
disc — this varies with the disc.
Displays a DVD disc menu — this
varies with the disc and may be
the same as the ‘top menu’.
MENU
Moves the cursor around the
screen.
Selects the current menu option.
ENTER
Returns to the previously
displayed menu screen. On some
DVD-Audio discs featuring
browsable pictures, press to
display the browser screen.
RETURN
1
2
3
4
5
6
7
8
9
CLEAR
0
ENTER
26
En
午後6時1分
Highlights a numbered menu
option (some discs only). Press
ENTER to select.
You can play a PBC Video CD/Super VCD
without having to navigate the PBC menu by
starting playback using a number button to
select a track, rather than the  (play) button.
Button
What it does
RETURN
Displays the PBC menu.
1
2
3
4
5
6
7
8
9
CLEAR
0
Selects numbered menu options.
Press ENTER to select.
ENTER
Displays the previous menu page
(if there is one).
Displays the next menu page
(if there is one).
LX03_En.book
27 ページ
2008年6月24日
火曜日
午後6時1分
Listening to your system
05
Listening to your system
With two channel sources, you can select from:
• Auto – See Auto listening mode above
The Auto listening mode is the simplest way to
listen to any source as it was mastered: the
output from the speakers mirrors the channels
in the source material.
• 2PL II Music (Dolby Pro Logic II Music)2 –
5.1 channel surround sound, especially
suited to music sources; see Dolby Pro
Logic II Music settings below
SURROUND
• Stereo – See Listening in stereo on page 29
• A.L.C. – See Listening in stereo on page 29
With multichannel sources, you can select
(according to format):
• Auto – See Auto listening mode above
• Stereo – See Listening in stereo on page 29
• A.L.C. – See Listening in stereo on page 29
Listening in surround sound
Dolby Pro Logic II Music settings
You can listen to stereo or multichannel
sources in surround sound. Surround sound is
generated from stereo sources using one of
the Dolby Pro Logic decoding modes.
When listening in Dolby Pro Logic II Music
mode (see above), there are three settings you
can adjust: Center Width, Dimension, and
Panorama.
• If you set up the system for Front surround
(page 7), the Front Stage Surround modes
will give the best results (page 28).
1
Press when Dolby Pro Logic II Music
mode is active.
Español
•
Press to select the Auto listening
mode.1
• When playing stereo sources, the STEREO
indicator will light. The 2D indicator will
light when playing a Dolby Surround sound
source.
• 2Pro Logic (Dolby Pro Logic)2 – 4.1
channel surround sound for use with any
two-channel source
Nederlands
• If you set up the system for Front surround
(page 7), the Front Stage Surround modes
will give the best results (page 28).
Italiano
Auto listening mode
• 2PL II Movie (Dolby Pro Logic II Movie)2
– 5.1 channel surround sound, especially
suited to movie sources
Français
• This unit’s audio function may be restricted
depending on the sound source, Line
Output setting (page 60), and HDMI audio
setting (page 63). In this event, the menus
may not appear, or a message may be
displayed instead (page 83).
SURROUND
•
Press repeatedly to select a
listening mode.1
The choices that appear in the display will vary
according to the type of source that’s playing.
Deutsch
Important
English
Chapter 5
SOUND
Note
1 • If the source is Dolby Digital or DTS, the corresponding indicator lights in the front panel display.
• During 88.2 kHz/96 kHz source playback, the listening mode is fixed to Auto and cannot be changed.
2 The 2PL II indicator will light.
27
En
LX03_En.book
05
28 ページ
2008年6月24日
火曜日
午後6時1分
Listening to your system
ENTER
2
Select ‘Center Width’,
‘Dimension’ or ‘Panorama’ then press
ENTER.
• Center Width – Provides a better blend of
the front speakers by spreading the center
channel between the front right and left
speakers, making it sound wider (higher
settings) or narrower (lower settings).
• Dimension – Adjusts the depth of the
surround sound balance from front to
back, making the sound more distant
(minus settings), or more forward (positive
settings).
• Panorama – Extends the front stereo
image to include the surround speakers for
a ‘wraparound’ effect.
ENTER
3
Adjust the setting, then press
ENTER to confirm.
• Unplugged – Suitable for acoustic music
sources
• Expanded – Creates an extra wide stereo
field.
• TV Surround – Provides surround sound
for both mono and stereo TV sources.
• Sports – Suitable for sports programs
• Advanced Game – Suitable for video
games
• Virtual – The virtual surround effect is
heard only from the front speakers, and
from the subwoofer.
• Ext Stereo – Gives multichannel sound to
a stereo source, using all of your speakers.
Using Front Stage Surround
Advance
The Front Stage Surround Advance modes are
effective when you are using the Front
surround setup as described on page 7.
ADV SURR
Using Advanced Surround
The Advanced Surround effects can be used
with any multichannel or stereo source for a
variety of additional surround sound effects.
These modes are designed to provide optimum
listening effect when using the Standard
surround setup described on page 7.
ADV SURR
•
Press to select an Advanced
Surround mode.
The ADV SURR indicator lights when one of
these modes is chosen. You cannot switch
between modes for some audio streams.1
Press repeatedly to select:
• Action – Designed for action movies with
dynamic soundtracks
•
Press to select a Front Stage
Surround Advance mode.
The F.S.SURR indicator lights. You cannot
switch between modes for some audio
streams.1
Press repeatedly to select:
• F.S.S.Focus5.1 – Use to provide a rich
surround sound effect directed to the
center area where the left and right
speakers sound projection converges.
• F.S.S.Wide5.1 – Use to provide a surround
sound effect to a wider area than
F.S.S.Focus5.1 mode.
• Extra Power – Outputs stereo sound (in
the case of multichannel sources, downmixed stereo sound) from the surround
speakers for powerful stereo effect.
Note
1 • During 88.2 kHz/96 kHz source playback, the listening mode is fixed to Auto and cannot be changed.
• When using a Pioneer flat screen TV with HDMI Control function support, these operating modes can be changed by
operating the TV.
28
En
LX03_En.book
29 ページ
2008年6月24日
火曜日
午後6時1分
Listening to your system
SOUND
RETRIEVER
•
Press while listening to a stereo
source.1
Press repeatedly to switch between:
• Retriever On — Switches the Sound
Retriever on. The S.RTRV indicator lights.
Listening with Acoustic
Calibration EQ
SOUND
1
• With headphones connected, press
SURROUND to select Stereo or A.L.C., or
press ADV SURR to select PhonesSurround.
• Stereo – See Listening in stereo above
• A.L.C. – See Listening in stereo above
• PhonesSurround – Virtual surround
sound for headphones.
2
ENTER.
Using the Sound Retriever
When audio data is removed during the MP3 or
WMA compression process, sound quality
often suffers from an uneven sound image. The
Sound Retriever feature employs new DSP
Press to open the sound menu.
ENTER
Select ‘MCACC EQ’ then press
ENTER
3
Switch ‘EQ On’ or ‘EQ Off’ then
press ENTER to confirm.
• The MCACC indicator lights when Acoustic
Calibration EQ is active.
Español
When headphones are connected, only the
Stereo, A.L.C. and PhonesSurround modes
are available.
Nederlands
Listening with headphones
Italiano
You can listen to sources using the Acoustic
Calibration Equalization set in Using the Auto
MCACC setup for optimal surround sound on
page 22.2
Français
• Retriever Off — Switches the Sound
Retriever off.
SURROUND
•
Press repeatedly to select Stereo or
A.L.C. mode.
• Stereo – The STEREO indicator will light
and ordinary stereo sound will be
produced.
• A.L.C. – Listening in Auto level control
stereo mode. The STEREO and ALC
indicators will light.
Deutsch
You can listen to any source — stereo or
multichannel — in stereo. When playing a
multichannel source, all channels are
downmixed to the front left/right speakers and
the subwoofer.
In the Auto level control stereo mode (A.L.C.),
this unit equalizes playback sound levels if
each sound level varies with the music source
recorded in a portable audio player.
technology that helps bring CD quality sound
back to compressed two channel audio by
restoring sound pressure and smoothing
jagged artifacts left over after compression.
English
Listening in stereo
05
• On the EQ Off setting, equalization is set to
off and speaker settings (channel delay
and channel level) remains as it is set.
• EQ On is selected automatically after the
Auto MCACC setup is completed.
Note
1 This setting cannot be used with multichannel or 88.2 kHz/96 kHz sources.
2 Acoustic Calibration EQ is not available when headphones are connected.
29
En
LX03_En.book
05
30 ページ
2008年6月24日
火曜日
午後6時1分
Listening to your system
• The TONE indicator lights.
Enhancing dialogue
The Dialogue Enhancement feature is
designed to make the dialogue stand out from
other background sounds in a TV or movie
soundtrack.
SOUND
1
Press to open the sound menu.
• To cancel the Midnight or Quiet listening
modes, select Bass/Treble.
Adjusting the bass and treble
Use the bass and treble controls to adjust the
overall tone.
SOUND
1
ENTER
2
ENTER.
Press to open the sound menu.
Select ‘Dialogue’ then press
ENTER
2
Select ‘Tone’ then press ENTER.
ENTER
3
Select the amount of Dialogue
Enhancement then press ENTER to confirm.
Select between Off, Mid, Max or Auto.
• When Dialogue is set to Auto, the amount
of Enhancement is selected automatically
to optimally match the audio signal.
• The DIALOG indicator lights when
Dialogue Enhancement is active.
Using Midnight and Quiet
listening modes
The Midnight listening feature allows you to
hear effective surround sound of movies at low
volume levels.
ENTER
3
Select ‘Bass/Treble’ then press
ENTER.
• Selecting Bass/Treble cancels the
Midnight and Quiet listening modes. These
modes cannot be used at the same time.
ENTER
4
Use / to select ‘Bass’ or
‘Treble’; use / to adjust the sound then
press ENTER to confirm.
• Bass and Treble can be adjusted from –6dB
to +6dB.
• When the Bass or Treble is set to
something other than 0dB, the TONE
indicator lights.
The Quiet listening feature reduces excessive
bass or treble in a sound source.
Boosting the bass level
SOUND
1
Press to open the sound menu.
There are two bass modes you can use to
enhance the bass in a source.1
SOUND
ENTER
Select ‘Tone’ then press ENTER.
2
1
ENTER
ENTER
3
Select ‘Midnight’ or ‘Quiet’ then
press ENTER to confirm.
2
ENTER.
Note
1 The Bass Mode is not available when headphones are connected.
30
En
Press to open the sound menu.
Select ‘Bass Mode’ then press
LX03_En.book
31 ページ
2008年6月24日
火曜日
Listening to your system
• The BASS MODE indicator lights when
Bass Mode is active.
There are a total of 60 steps (levels) that you
can adjust, with a total range of 200 msec.
Press to open the sound menu.
ENTER
2
ENTER.
Select ‘Sound Delay’ then press
Español
ENTER
3
Select the length of the delay in
sound, then press ENTER to confirm.
• This option is deactivated and not
displayed if you have Auto Delay set to On
in HDMI Setup (see Setting the Auto Delay
on page 64).
Nederlands
SOUND
1
Italiano
Some monitors have a slight delay when
showing video, so the soundtrack will be
slightly out of sync with the picture. By adding
a bit of delay, you can adjust the sound to
match the presentation of the video.
Français
Adjusting sound delay
Deutsch
• When Bass Mode is set to Auto, the
setting (Music or Cinema) is selected
automatically to optimally match the audio
signal.
05
English
ENTER
3
Select the desired Bass Mode
setting, then press ENTER to confirm.
Select between Off, Music, Cinema or Auto.
午後6時1分
31
En
LX03_En.book
06
32 ページ
2008年6月24日
火曜日
午後6時1分
Disc playback features
Chapter 6
Disc playback features
Important
• Many of the functions covered in this
chapter apply to DVD and SACD discs,
Video CDs/Super VCDs, CDs, DivX video/
WMV and WMA/MP3/MPEG-4 AAC/JPEG
discs, although the exact operation of
some varies slightly with the kind of disc
loaded.
• Some DVDs restrict the use of some
functions (random or repeat, for example)
in some or all parts of the disc. This is not a
malfunction.
• When playing Video CD/Super VCDs, some
of the functions are not available during
PBC playback. If you want to use them,
start the disc playing using a number
button to select a track.
Scanning discs
You can fast-scan discs forward or backward at
various different speeds.1
/
/
•
During playback, start reverse
or forward scanning.
Press repeatedly to increase the scanning
speed (shown on-screen).
• To resume playback, press  (play).2
Playing in slow motion
You can play DVD-Videos and DVD-R/-RW at
four different slow motion speeds, forwards
and backwards. Video CD/Super VCDs and
DivX video/WMV can be played at four different
forward slow motion speeds.
1
Pause playback.
/
/
2
Press and hold to start slow
motion reverse or forward play.
Press repeatedly to change the slow motion
speed (shown on-screen).
• To resume playback, press  (play).2
Frame advance/frame reverse
You can advance or back up DVD-Video and
DVD-R/-RW discs frame-by-frame. With Video
CD/Super VCDs and DivX video/WMV file you
can only use frame advance.
1
Pause playback.
/
/
2
Back up or advance one frame
with each press.
• To resume playback, press  (play).2
Note
1 Only one speed is available for DivX video/WMV discs.
2 • Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc.
• For Video CDs/Super VCDs in PBC mode and WMA/MP3/MPEG-4 AAC tracks (in Scan mode only), normal playback resumes
when you reach the beginning or the end of track.
32
En
LX03_En.book
33 ページ
2008年6月24日
火曜日
午後6時1分
Disc playback features
Use the Disc Navigator to browse through the
contents of a DVD-Video, VR mode DVD-R/-RW
or Video CD/Super VCD disc to find the part
you want to play.
HOME MENU
ENTER
1
During playback, select
‘Disc Navigator’ from the on-screen menu.
Pictures are automatically adjusted so that
they fill as much of the screen as possible.
While the slideshow is running:
Pauses the slideshow (or audio);
press again to restart.
Jumps to the next picture (or
audio file with audio playback).
Disc Navigator
Title
Chapter
The options available depend on the kind of
disc loaded and whether the disc is playing or
not, but include:
• Title – Titles from a DVD-Video disc.
Pauses the slideshow and
rotates/flips the displayed
picture (Press  (play) to restart
slideshow).
• Chapter – Chapters from the current title
of a DVD-Video disc.
Pauses the slideshow and zooms
the picture. Press again to toggle
between 1x, 2x and 4x zoom
(Press  (play) to restart
slideshow).
• Time – Thumbnails from a Video CD/Super
VCD disc at 10 minute intervals.
Displays the Disc Navigator
screen (see below).
• Track – Tracks from a Video CD/Super VCD
disc.
Español
MENU
Select a view option.
Nederlands
Jumps to the previous picture (or
audio file with audio playback).
ZOOM
2
What it does
Italiano
Button
Disc Navigator
Français
• If the folder contains WMA/MP3/MPEG-4
AAC files, playback of the slideshow and
WMA/MP3/MPEG-4 AAC file repeats.
During the audio playback, you can still
use the skip (/), scan (/)
and pause () functions.
Browsing DVD or Video CD/
Super VCD discs with the Disc
Navigator
Deutsch
After loading a disc containing JPEG pictures,
press  (play) to start a slideshow from the first
folder/picture on the disc.1 The player displays
the pictures in each folder in alphabetical
order.
English
Playing a JPEG slideshow
06
• Original: Title – Original titles from a VR
mode DVD-R/-RW disc.
• Playlist: Title – Playlist titles from a VR
mode DVD-R/-RW disc.
• Original: Time – Thumbnails from the
Original content at 10 minute intervals.
• Playlist: Time – Thumbnails from the
Playlist at 10 minute intervals.
Note
1 • The time it takes for the player to load a file increases with large file sizes.
• Discs can contain up to 299 folders and up to 648 folders and files combined.
33
En
LX03_En.book
06
34 ページ
2008年6月24日
火曜日
午後6時1分
Disc playback features
The screen shows up to six moving thumbnail
images displayed one after another. To display
the previous/next six thumbnails, press /
.
3 Select the thumbnail image for what
you want to play.
01
02
03
04
05
06
ENTER
2
Use for navigating folders and
files.
Use / to move up and down the folder/file
list.
Use  to return to the parent folder.1
Use ENTER or  to open a highlighted folder.
• When a JPEG file is highlighted, a
thumbnail image is displayed on the right.
00:00/ 00:00
Disc Navigator: Title
01- 49: - -
0kbps
Folder2
You can use either /// and ENTER to
select a thumbnail, or the number buttons.
File1
To select using the number buttons, enter a
two-digit number then press ENTER.
File5
Browsing Windows Media™
Audio (WMA), MP3, MPEG-4
AAC, DivX video/WMV and JPEG
files with the Disc Navigator
Use the Disc Navigator to find a particular file
or folder by filename.
File2
File3
File4
3 To play the highlighted track or DivX
video/WMV file or display the highlighted
JPEG file, press ENTER.
• When a WMA/MP3/MPEG-4 AAC or DivX
video/WMV file is selected, playback
begins from that file, and continues until
the end of the folder.
• When a JPEG file is selected, a slideshow
begins, starting with that file, and
continues to the end of the folder.
HOME MENU
ENTER
1
Select ‘Disc Navigator’
from the on-screen menu.
00:00/ 00:00
Folder1
Folder2
Folder3
Folder4
0kbps
Tip
• You can also play a JPEG slideshow while
listening to WMA/MP3/MPEG-4 AAC
playback. Simply select the audio file you
want to listen to followed by the JPEG from
which you want the slideshow to start.
Playback of both the slideshow and the
audio files repeats. Playback controls are
effective for the JPEG slideshow only.
• To play the contents of the whole disc
rather than just the current folder, exit the
Disc Navigator and start playback using 
(play).
Note
1 You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.
34
En
LX03_En.book
35 ページ
2008年6月24日
火曜日
午後6時1分
Disc playback features
• With playback stopped, press PLAYLIST
1, 2 or 3.
During playback, PGM lights in the front panel
display. If no playlist has been programmed,
No PLAYLIST shows in the display.
• If the playlist contains both JPEG and
audio files, playback of the slideshow and
audio files starts.
Programming playlists
Deutsch
With this feature, you can make up to three
playlists of 30 files each for discs containing
WMA, MP3, MPEG-4 AAC and JPEG files.
Since this unit will remember all playlists for
the last ten discs you have loaded, this is useful
if you have a large number of files that you want
to organize quickly and easily.1
Listening to playlists
English
Using playlists
06
Clearing files from a playlist
ENTER
1
With the disc stopped,
select ‘Disc Navigator’ from the on-screen
menu.
1
2 From the ‘Disc Navigator’ screen,
highlight the file you want to remove from
the playlist and press CLEAR.
Looping a section of a disc
The A-B Repeat function allows you to specify
two points (A and B) within a track (CD, Video
CD/Super VCD) or title (DVD-Video and DVDRW) that form a loop which is played over and
over.
3
3
Press PLAYLIST 1, 2 or 3.
The file is added to the playlist you select.
4
Repeat steps 2 and 3 until you’re done.
HOME MENU
ENTER
Tip
1
‘Play Mode’.
• To add files without the on-screen display,
simply press PLAYLIST 1, 2 or 3 during
normal playback of the file you want
(except when a JPEG slideshow is playing
at the same time as audio).
During playback, select
Español
• You can’t use A-B Repeat with DVD-Audio,
SACD, Video CD/Super VCDs in PBC
mode, or WMA/MP3/MPEG-4 AAC/DivX
video/WMV files.
2
Nederlands
PLAYLIST
Start playback of your playlist.
Italiano
2 Select the file you want to add to the
playlist.
See Browsing Windows Media™ Audio (WMA),
MP3, MPEG-4 AAC, DivX video/WMV and JPEG
files with the Disc Navigator above if you don’t
know how to do this.
1
Français
HOME MENU
Play Mode
Note
1 The disc must be loaded for the files in your playlist to play back.
35
En
LX03_En.book
06
36 ページ
2008年6月24日
火曜日
午後6時1分
Disc playback features
ENTER
2
Select ‘A-B Repeat’.
ENTER
3
Press at the desired starting point
(A(Start Point)) to set the loop start point.
Using random play
Use the random play function to play titles or
chapters (DVD-Video), Groups (DVD-Audio), or
tracks (DVD-Audio, SACD, CD, Video CD/
Super VCD) at random. (Note that the same
track/title/chapter may play more than once.)2
ENTER
4
Press at the desired ending point
(B(End Point)) to set the loop end point.
After pressing ENTER, playback jumps back to
the start point and plays the loop.
1
‘Play Mode’.
5
2
To resume normal playback, select ‘Off’.
Using repeat play
In addition to various repeat play options, it’s
also possible to use repeat play together with
program play (see Creating a program list on
page 37).
HOME MENU
ENTER
During playback, select
Select ‘Random’ then select an option.
• For DVD discs, select Random Title or
Random Chapter.
• For DVD-Audio discs, select Random
Group or Random Track.
• For CDs, SACDs and Video CD/Super
VCDs, select On or Off to switch random
play on or off.
HOME MENU
ENTER
1
‘Play Mode’.
Tip
During playback, select
2 Select ‘Repeat’ then select a repeat play
option.1
If program play is active, select Program
Repeat to repeat the program list, or Repeat
Off to cancel.
• For DVD discs, select Title Repeat or
Chapter Repeat.
• For DVD-Audio discs, select Group
Repeat or Track Repeat.
• For SACDs, CDs and Video CD/Super
VCDs, select Disc Repeat or Track Repeat.
• For DivX video/WMV discs, select Title
Repeat (or Repeat Off).
• Use the following controls during random
play:
Button
What it does
Selects a new track/title/chapter
at random.
Returns to the beginning of the
current track/title/chapter;
further presses select another
random track/title/chapter.
• Random play remains in effect until you
select Random Off from the random play
menu options.
Note
1 You can’t use repeat play with Video CD/Super VCDs in PBC mode, or with WMA/MP3/MPEG-4 AAC discs.
2 • You can set the random play option when a disc is playing or stopped. However, you can’t use random play together with
program play.
• You can’t use random play with VR format DVD-R/-RW discs, Video CD/Super VCDs playing in PBC mode, WMA/MP3/MPEG4 AAC discs, DivX video/WMV discs, or while a DVD disc menu is being displayed.
36
En
LX03_En.book
37 ページ
2008年6月24日
火曜日
午後6時1分
Disc playback features
06
This feature lets you program the play order of
titles/chapters/groups/tracks on a disc.1
Tip
• Use the following controls during program
play:
Button
HOME MENU
English
Creating a program list
What it does
ENTER
During playback, select
2 Select ‘Program’ then select ‘Create/Edit’
from the list of program options.
• For a CD, SACD or Video CD/Super VCD,
select a track to add to the program list.
Other functions available from the
program menu
There are a number of other options in the
program menu in addition to Create/Edit.
• Playback Start – Starts playback of a
saved program list
• Playback Stop – Turns off program play,
but does not erase the program list
• Program Delete – Erases the program list
and turns off program play
4 Repeat step 3 to build up a program list.
A program list can contain up to 24 steps.
Español
• You can insert steps by just highlighting
the position where you want the new step
to appear and entering a title/chapter/
group/track number.
Nederlands
After pressing ENTER to select the title/
chapter/track, the step number automatically
moves down one.
Skip to the next step in the
program list.
Italiano
• For a DVD-Audio disc, you can add a whole
group, or a track within a group to the
program list.
Save the program list and exit
without starting playback.
Français
ENTER
3
Select a title, chapter or track for
the current step in the program list.
• For a DVD disc, you can add a title or a
chapter.
HOME MENU
Deutsch
1
‘Play Mode’.
• To delete a step, highlight it and press
CLEAR.
5
Play the program list.
Program play remains active until you turn off
program play (see below), erase the program
list (see below), eject the disc or switch off.
Note
1 You can’t use program play with VR format DVD-R/-RW discs, Video CD/Super VCDs playing in PBC mode, WMA/MP3/MPEG4 AAC discs, DivX video/WMV discs, or while a DVD disc menu is being displayed.
37
En
LX03_En.book
06
38 ページ
2008年6月24日
火曜日
午後6時1分
Disc playback features
Searching a disc
Switching subtitles
You can search DVD-Video discs by title or
chapter number, or by time; DVD-Audio discs
can be searched by group or track number;
SACDs by track number, CDs and Video CD/
Super VCDs by track number or time; DivX
video /WMV discs by time.1
Some DVD discs and DivX video discs have
subtitles in one or more languages; the disc
box will usually tell you which subtitle
languages are available. You can switch
subtitle language during playback.2
SUBTITLE
HOME MENU
ENTER
1
Select ‘Play Mode’.
2 Select ‘Search Mode’.
The search options that appear depend on the
kind of disc loaded.
3
Select a search mode.
• The disc must be playing in order to use
time search.
1
2
3
4
5
6
7
8
9
0
4
Enter a title, chapter or track
number, or a time.
• For a time search, enter the number of
minutes and seconds into the currently
playing title (DVD/DivX video/WMV) or
track (CD/Video CD/Super VCD) you want
playback to resume from. For example,
press 4, 5, 0, 0 to have playback start from
45 minutes into the disc. For 1 hour, 20
minutes and 30 seconds, press 8, 0, 3, 0.
CLEAR
• Some DVD-Audio discs feature pages of
browsable pictures. Enter the page
number you want.
5
ENTER
•
Press repeatedly to select a subtitle
option.
• To set subtitle preferences, see Language
settings on page 54.
• See Displaying DivX subtitle files on
page 75 for more on DivX subtitles.
Switching language/audio
channels
When playing discs recorded with dialogue in
two or more languages, or with dual-mono
audio3 you can switch these during playback.4
When playing a DVD-Audio disc, you may be
able to switch channels — see the disc box for
details. (When you change the audio channel,
playback restarts from the beginning of the
current track.)
When playing a Video CD/Super VCD, you can
switch between stereo, just the left channel or
just the right channel.
AUDIO
•
Press repeatedly to select an audio
language option.
• To set audio language preferences, see
Language settings on page 54.
Start playback.
Note
1 Search functions are not available with Video CD/Super VCDs in PBC mode, or with WMA/MP3/MPEG-4 AAC discs.
2 Some discs only allow you to change subtitle language from the disc menu. Press TOP MENU or MENU to access.
3 Some Super VCDs have two soundtracks. With these discs you can switch between the two soundtracks as well as individual
channels in each.
4 Some discs only allow you to change audio language from the disc menu. Press TOP MENU or MENU to access.
38
En
LX03_En.book
39 ページ
2008年6月24日
火曜日
午後6時1分
Disc playback features
Using the zoom feature you can magnify a part
of the screen by a factor of 2 or 4, while
watching a DVD, DivX video/WMV title or Video
CD/Super VCD or playing a JPEG disc.
Français
2
Change the zoomed area.
You can change the zoom factor and the
zoomed area freely during playback.1
Deutsch
ZOOM
1
During playback, press repeatedly to
select the zoom factor (Normal, 2x or 4x).
English
Zooming the screen
06
Switching camera angles
ANGLE
•
During playback (or when paused),
press to switch angle.
Various track, chapter and title information can
be displayed on-screen during playback.
Español
Displaying disc information
Nederlands
When a multi-angle scene is playing, a
icon
appears on screen (this can be switched off if
you prefer — see Display settings on page 55).
Italiano
Some DVD discs feature scenes shot from two
or more angles — check the disc box for
details.
DISPLAY
•
Press repeatedly to show, change,
and hide the disc information display.
Limited disc information also appears in the
front panel display. Press DISPLAY to change
the displayed information.
Note
1 • Since DVD, Video CD/Super VCD, DivX video/WMV title and JPEG pictures have a fixed resolution, picture quality will
deteriorate, especially at 4x zoom. This is not a malfunction.
• If the navigation square at the top of the screen disappears, press ZOOM again to display it.
39
En
LX03_En.book
07
40 ページ
2008年6月24日
火曜日
午後6時1分
iPod/USB playback
Chapter 7
iPod/USB playback
Connecting your iPod to this unit
Connecting an iPod
This unit has a dedicated iPod terminal that
will allow you to control playback of audio
content from your iPod using the controls of
this unit.1
2 Switch the unit on and press the iPod
input source button on the remote control to
switch the unit to the iPod.
The front panel display shows Loading while
the unit verifies the connection and retrieves
data from the iPod.
iPod DIRECT /USB
OPEN/CLOSE
PHONES
1 Set this unit to the standby mode, and
then use the USB cable (for iPod connection)2
to connect your iPod to the iPod DIRECT/USB
terminal on the front panel of this unit.
For the cable connection, refer to also the
operating instructions for iPod.
MCACC
iPod DIRECT/USB
3 Press TOP MENU to display iPod Top
menu.
When the display shows Top Menu you’re
ready to play music from the iPod.3
USB cable (for
iPod connection)
iPod
MENU


• If after pressing iPod the display shows
No Device, try switching off the unit and
reconnecting the iPod to the unit.

iPod playback
To navigate songs on your iPod, you can take
advantage of the OSD of your TV connected to
this unit.4 You can also control all operations
for music in the front panel display of this unit.
Note
1 • This unit is compatible with the audio of iPod nano, iPod fifth generation, iPod classic, iPod touch (not supported iPod shuffle
and iPhone). However, that some of the functions may be restricted for some models. Note, however, compatibility may vary
depending on the software version of your iPod. Please be sure to use the latest available software version.
• iPod is licensed for reproduction of non-copyrighted materials or materials the user is legally permitted to reproduce.
• Features such as the equalizer cannot be controlled using this unit, and we recommend switching the equalizer off before
connecting.
• Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from any inconvenience
or loss of recorded material resulting from the iPod failure.
2 The USB cable (for iPod connection) is not included with this unit.
3 The controls of your iPod will be inoperable when connected to this unit. Features such as the equalizer cannot be controlled
using this unit, and we recommend switching the equalizer off before connecting.
4 • Note that non-roman characters in the title are displayed as #.
• This feature is not available for photos or video clips on your iPod.
40
En
LX03_En.book
41 ページ
2008年6月24日
火曜日
午後6時1分
iPod/USB playback
07
Basic playback controls
When your iPod is connected to this unit, you
can browse songs stored on your iPod by
playlist, artist, album name, song name, genre
or composer, similar to using your iPod directly.
The following table shows the basic playback
controls for your iPod. Press iPod to switch the
remote control to the iPod operation mode.
Button
What it does
Playlists
001/009
/
/
ENTER
Press to skip to previous/next track.
Press repeatedly to switch between
Repeat One, Repeat All and Repeat
Off.
ENTER
DISPLAY
Playlists  Songs
Artists  Albums  Songs
Albums  Songs
Songs
Podcasts
Genres  Artists  Albums  Songs
Composers  Albums  Songs
Audiobooks
Shuffle Songs
Press repeatedly to change the song
playback information displayed in the
front panel display.
When browsing, press to move to
previous/next levels. During playback,
press to skip to previous/next track.
During Audiobook playback, press to
switch the playback speed: Faster 
Normal  Slower
TOP
MENU
Press to return to the iPod Top menu
screen.
RETURN
Press to return to the previous level.
Español
3 Continue browsing until you arrive at
what you want to play, then press  to start
playback.1
Navigation through categories on your iPod
looks like this:
Nederlands
Press repeatedly to switch between
Shuffle Songs, Shuffle Albums and
Shuffle Off.
2
Browse the selected category
(e.g., albums).
• Use / to move to previous/next levels.
Italiano
1
Select a category, then press
ENTER to browse that category.
• To return to the previous level any time,
press RETURN.
Press and hold during playback to start
scanning.
Français
Pauses playback, or restarts playback
when paused.
Deutsch
Press to start playback.
If you start playback when something
other than a song is selected, all the
songs that fall into that category will
play.
iPod Navigator
English
Finding what you want to play
Tip
• You can play all of the songs in a particular
category by selecting the All item at the top
of each category list. For example, you can
play all the songs by a particular artist.
Note
1 If you’re in the song category, you can also press ENTER to start playback.
41
En
LX03_En.book
07
42 ページ
2008年6月24日
火曜日
午後6時1分
iPod/USB playback
Important
If an error message lights in the front panel
display, try following the points below:
Symptom What it means
Error I1
Error I2
Error I3
There is a problem with the signal path
from the iPod to the unit. Switch off the
unit and reconnect the iPod to the unit.
If this doesn’t seem to work, try resetting
your iPod.
The software version being used with
the iPod needs to be updated. Update
the software being used with the iPod
(please use the latest iPod software
versions later than the iPod updater
2004-10-20).
The iPod that is not supported is
connected. Check whether the iPod was
supported by this unit (page 40).
When the iPod software version is too
old, update the iPod software to the
latest version.
Error I4
When there is no response from the
iPod, update the iPod software to the
latest version. If this doesn’t seem to
work, try resetting your iPod.
iPod Error The power requirements of the iPod are
too high for this unit.
Switching the iPod controls1
You can switch over the iPod controls between
the iPod and the unit.
1 CTRL Press to switch the iPod controls.2
This enables operation and display on your
iPod, and this unit’s remote control and OSD
become inactive.
2 CTRL Press again to switch back to the
receiver controls.
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
Using the USB interface
It is possible to listen to two-channel audio3
and watch JPEG files using the USB interface
on the front of this unit. Connect a USB mass
storage device4 as shown below.
1 USB With the system switched on, press
USB.
Make sure your TV is on and set to the correct
video input.
2
Connect your USB memory device.
No Music There are no playable songs currently
Track
stored in the iPod. Input some music
files compatible with iPod playback.
No Track When there are no tracks in the
category selected on the iPod. Select a
different category.
Note
1
2
3
4
42
En
You cannot use this function, when an iPod of fifth generation or iPod nano of first generation is connected.
When this function is set, iPod images cannot be played on this unit.
This includes playback of WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback).
• Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital
audio players (MP3 players) of format FAT16/32. It is not possible to connect this unit to a personal computer for USB playback.
• Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no
responsibility for any loss of data that may occur when connected to this unit.
• With large amounts of data, it may take longer for the system to read the contents of a USB device.
LX03_En.book
43 ページ
2008年6月24日
火曜日
午後6時1分
iPod/USB playback
The USB terminal is located on the front panel.
MCACC
Button
What it does
English
PHONES
Basic playback controls
The following table shows the basic controls on
the remote for USB playback.
iPod DIRECT /USB
OPEN/CLOSE
07
Starts normal playback.
Pauses/unpauses playback.
Stops playback.
Press to start fast reverse scanning.
/
Press to start fast forward scanning.
/
3
Start playback.
If your USB memory device contains JPEGs, a
slideshow will start. See Playing a JPEG
slideshow below for more on this.
• Switch the player off, then on again.
• Reconnecting the USB device with the
player switched off.
• Selecting to another input source (like
DVD/CD), then back to USB.
• Using a dedicated AC adaptor (supplied
with the device) for USB power.
If this doesn’t remedy the problem, it is likely
your USB device is incompatible.
Scanning files
You can fast-scan forward or backward at
various different speeds.
/
/
•
During playback, start reverse
or forward scanning.
Press repeatedly to increase the scanning
speed (shown on-screen).
• To resume playback, press  (play).1
Playing a JPEG slideshow
Español
If a USB Error message lights in the display, it
may mean that the power requirements of the
USB device are too high for this unit, or that the
device is incompatible. Try the following:
Skips to the next file.
Nederlands
Important
Skips to the start of the current file,
then previous files.
Italiano
• Make sure USB DATA is showing in the
front panel display (or the system is in
standby) when disconnecting.
Français
USB mass
storage device
Deutsch
iPod DIRECT/USB
Press  to start a slideshow from the first
folder/picture.2 The pictures in each folder are
displayed in order.
• If the device contains WMA/MP3/MPEG-4
AAC files, playback of the slideshow and
audio files repeats. During audio playback,
you can still use the skip (/), scan
(/) and pause () functions.
Note
1 With WMA/MP3/MPEG-4 AAC tracks, playback automatically resumes at the end or beginning of the track.
2 • The time it takes for the player to load a file increases with large file sizes.
• USB devices can contain up to 299 folders and up to 648 folders and files combined.
43
En
LX03_En.book
07
44 ページ
2008年6月24日
火曜日
午後6時1分
iPod/USB playback
Pictures are automatically adjusted so that
they fill as much of the screen as possible.
While the slideshow is running:
Button
What it does
Pauses the slideshow (or audio);
press again to restart.
Jumps to the previous picture (or
audio file with audio playback).
Jumps to the next picture (or audio
file with audio playback).
Pauses the slideshow and rotates/
flips the current picture (Press  to
restart slideshow).
Pauses the slideshow and zooms
the picture. Press again to toggle
between 1x, 2x and 4x zoom (Press
 to restart slideshow).
ZOOM
Displays the Navigator screen (see
below).
MENU
3 To play the highlighted track or display
the highlighted JPEG file, press ENTER.
• When a WMA/MP3/MPEG-4 AAC file is
selected, playback begins from that file,
and continues until the end of the folder.
• When a JPEG file is selected, a slideshow
begins, starting with that file, and
continues to the end of the folder.
Tip
• You can also play a JPEG slideshow while
listening to WMA/MP3/MPEG-4 AAC
playback. Simply select the audio file you
want to listen to followed by the JPEG from
which you want the slideshow to start.
Playback of both the slideshow and the
audio files repeats. Playback controls are
effective for the JPEG slideshow only.
• To play all of the contents, rather than just
the current folder, exit the Navigator and
start playback using  (play).
Browsing files with the Navigator
Use the Navigator to find WMA, MP3, MPEG-4
AAC and JPEG files or folders by name.1
MENU
1
Press MENU.
ENTER
2
Use for navigating folders and
files.
Use / to move up/down the folder/file list.
Use  to return to the parent folder.2
Use ENTER or  to open a highlighted folder.
• When a JPEG file is highlighted, a
thumbnail image is displayed on the right.
Note
1 Filenames may be displayed incorrectly with some digital audio players.
2 You can also do this by going to the ‘..’ folder at the top, then pressing ENTER.
44
En
LX03_En.book
45 ページ
2008年6月24日
火曜日
午後6時1分
Listening to the radio
08
Listening to the radio
The tuner can receive both FM and AM
broadcasts, and lets you memorize your
favorite stations so you don’t have to manually
tune in every time you want to listen.
TUNE
• High-speed tuning – Press and hold
TUNE +/– until the frequency display starts
to move rapidly. Keep the button held down
until you reach the frequency you want. If
necessary, fine tune the frequency using
the manual tuning method.
Select ‘Tuner Setup’ then press
ENTER
3
Choose ‘FM Auto/Mono’ then
press ENTER.
ENTER
4
Select ‘FM Mono’ then press
ENTER.
The mono indicator ( ) lights when the tuner
is in mono reception mode.
Select FM Auto above to switch back to autostereo mode (the stereo indicator (
) lights
when receiving a stereo broadcast).
Español
• Auto tuning – Press and hold TUNE +/–
until the frequency display starts to move,
then release. The tuner will stop on the next
station it finds. Repeat to keep searching.
ENTER
2
ENTER.
Nederlands
• Manual tuning – Press TUNE +/–
repeatedly to change the displayed
frequency.
SETUP
1
Press after tuning to an FM radio
station.
Italiano
2
Tune to a frequency.
TUNE
There are three tuning modes — manual, auto,
and high-speed:
If you’re listening to an FM station in stereo but
the reception is weak, you can improve the
sound quality by switching to mono.
Français
FM/AM
1 TUNER Switch to the tuner, then press
repeatedly to select the FM or AM band.
The display shows the band and frequency.
Improving poor FM reception
Deutsch
Listening to the radio
English
Chapter 8
Improving poor AM sound
The simplest way to improve the sound quality
of AM radio is to make sure that the TV in the
room is switched off. Also try changing the
position and direction of the AM loop antenna.
45
En
LX03_En.book
08
46 ページ
2008年6月24日
火曜日
午後6時1分
Listening to the radio
Changing the noise cut mode
If you find that the AM sound quality is bad
even after trying the above, you may be able to
improve it using a different noise cut mode.
Just choose the one that sounds best.
SETUP
1
Press after tuning to an AM radio
station.
Listening to station presets
You will need to have some presets stored to do
this.
CLASS
1
Press to select the class in which the
channel is stored.
Press repeatedly to cycle through classes A, B
and C.
ST
ENTER
2
ENTER.
Select ‘Tuner Setup’ then press
ENTER
3
ENTER.
Choose ‘Noise Cut’ then press
ENTER
4
Select a Noise cut mode (1, 2 or 3)
then press ENTER.
Memorizing stations
This system can memorize up to 30 stations,
stored in three banks, or classes (A, B and C) of
10 stations each.
1 Tune to an FM or AM radio station.
Select mono or auto-stereo reception (FM) or
the Noise Cut mode (AM) as necessary. These
settings are saved along with the preset.
T.EDIT
2
Press T.EDIT.
CLASS
3
Press to select one of the three
classes, then press ST +/– to select the station
preset you want.
You can also use the number buttons to select
a preset.
ENTER
4
Press ENTER.
After pressing ENTER, the preset class and
number stop blinking and the system
memorize station.
46
En
ST
2
Select the station preset you
want.
• You can also use the number buttons on
the remote control to recall the station
preset.
LX03_En.book
47 ページ
2008年6月24日
火曜日
午後6時1分
Listening to the radio
08
Use DISPLAY to display the different types of
RDS information available.2
DISPLAY
•
Press for RDS information.
Each press changes the display as follows:
• Radio Text (RT) – Messages sent by the
radio station. For example, a talk radio
station may provide a phone number as RT.
One feature of RDS is that you can search by
type of program. For example, you can search
for a station that’s broadcasting a show with
the program type, Jazz.
You can search the following program types:
• Program Type (PTY) – This indicates the
kind of program currently being broadcast.
• PTY SEARCH – PTY search (see below)
• Current tuner frequency
Searching for RDS programs
You can search for a program type listed above.
1
FM/AM
TUNER
Press for the FM band.3
DISPLAY
2
Press repeatedly until ‘PTY
SEARCH’ appears in the display.
Select the program type you want
4 ENTER Start the search.
The system searches the station presets for a
match. If it finds one, searching stops for five sec.
Español
3
to hear.
Nederlands
Finance – Stock market
reports, commerce,
trading, etc.
Children – Programs for
children
Social – Social affairs
Religion – Programs
concerning religion
Phone In – Public
expressing their views by
phone
Travel – Holiday-type travel
information as opposed to
traffic announcements.
Leisure – Leisure interests
and hobbies
Jazz – Jazz
Country – Country music
Nation M – Popular music
in a language other than
English
Oldies – Popular music
from the ’50s and ’60s
Folk M – Folk music
Document – Documentary
Italiano
News – News
Affairs – Current Affairs
Info – General Information
Sport – Sport
Educate – Educational
Drama – Radio plays, etc.
Culture – National or
regional culture, theater,
etc.
Science – Science and
technology
Varied – Usually talkbased material, such as
quiz shows or interviews.
Pop M – Pop music
Rock M – Rock music
Easy M – Easy listening
Light M – ‘Light’ classical
music
Classics – ‘Serious’
classical music
Other M – Music not fitting
above categories
Weather – Weather
reports and forecasts,
meteorological information
Français
• Program Service Name (PS) – The name of
the radio station.
1
Deutsch
Radio Data System (RDS) is a system used by
most FM radio stations to provide listeners with
various kinds of information — the name of the
station and the kind of show they’re
broadcasting, for example.
English
Displaying RDS information
Using RDS
5 If you want to keep listening to the
station, press ENTER within the five seconds.
If you don’t press ENTER, searching resumes.
Note
1 In addition, there are three other program types, TEST, ALARM!, and None, ALARM! and TEST are used for emergency
announcements. None appears when a program type cannot be found.
2 • If any noise is picked up while displaying the RT scroll, some characters may be displayed incorrectly.
• If you see No Radio Text Data in the RT display, it means no RT data is sent from the broadcast station. The display will
automatically switch to the PS data display (if no PS data, the frequency is displayed).
• In the PTY display, NO DATA or None may be shown. In this case, the PS display is shown after a few seconds.
3 RDS is only possible in the FM band.
47
En
LX03_En.book
09
48 ページ
2008年6月24日
火曜日
午後6時1分
Surround sound settings
Chapter 9
Surround sound settings
• Dynamic Range Compression
Resuscitates detailed sound susceptible to
ambient noise to create an acoustic
environment where you feel as if you are
right in the action.
Important
• This unit’s audio function may be restricted
depending on the Line Output setting
(page 60) and HDMI audio setting
(page 63). In this event, the menus may not
appear.
• Frequency Characteristic Correction
Realizes the playback characteristic
optimized for long hours of listening in
addition to the added features of the
supplied speaker units.
Using the Sound Setup menu
From the Sound Setup menu you can access
all the surround sound settings of the system.
During setup, the speakers are represented by
the following letters:
• L – Front left speaker
• C – Center speaker
The Effective Sound mode can be turned off
(activating Direct Sound mode) by doing the
following:
SETUP
1
Press SETUP.
• R – Front right speaker
ENTER
• SR – Surround right speaker
• SL – Surround left speaker
2
ENTER.
Select ‘Sound Setup’, then press
• SW – Subwoofer
ENTER
Effective Sound (for optimum
sound)
With the uniquely shaped high-quality
speakers supplied with this unit, the Effective
Sound mode enables the following Pioneer
exclusive audio technologies designed to
maximize the real experience of sound
originally inherent in movies and music.
Turn on the Effective Sound mode under
normal circumstances to maximize the
capabilities of this unit.1
3
ENTER.
ENTER
4
Select ‘Direct Sound’, then press
ENTER to confirm.
To return to Effective Sound mode, perform the
same procedure noted above to select
‘EffectiveSound’.
• When Direct Sound is selected, the
DIRECT indicator lights.
Note
1 The Sound Field setting is not available when headphones are connected.
48
En
Select ‘Sound Field’, then press
LX03_En.book
49 ページ
2008年6月24日
火曜日
午後6時1分
Surround sound settings
Speaker distance setting
The Auto MCACC feature (see page 22) should
give you the best surround sound setup.
However you may find that by further
adjustment of the speaker distance settings
you can improve the surround sound in your
listening room.
This method of setting the channel levels
allows you to listen to a source and adjust the
levels of each playback channel.
Set the distance of each speaker from your
normal listening position.
SETUP
1
menu.
SETUP
1
menu.
ENTER
Open the ‘Sound Setup’
ENTER
Open the ‘Sound Setup’
ENTER
Select ‘Distance’, then press
Select ‘ChannelLevel’, then press
ENTER
ENTER
Press ENTER when you’re finished.
• If you use the Auto MCACC feature again,
it will overwrite the settings you have made
here.
Press once when you’re finished.
• If you use the Auto MCACC feature again,
it will overwrite the settings you have made
here.
Español
4
4
Nederlands
3
Use / to select a channel3 or
/ to adjust the level of that channel.
• You can adjust the level of each channel by
±10 dB.
3
Use / to select a speaker or
/ to adjust the distance.
Each speaker can be adjusted from 0.1m to
9.0m.
Italiano
2
ENTER.
ENTER
2
ENTER.
Français
The test tone method can also be used to
adjust channel levels.2
Deutsch
The Auto MCACC feature (see page 22) should
give you the best surround sound setup.
However you may find that by further
adjustment of the channel levels you can
improve the surround sound in your listening
room.
English
Channel level setting1
09
Note
1 The Channel level setting is not available when headphones are connected.
2 No test tone is output when audio is muted.
3 When Test Tone is selected, the test tone moves automatically from speaker to speaker in the order
LCRSRSLSW. Adjust the / controls so that the test tone is heard at the same volume from each speaker when
sitting in the main listening position. However, the test tone from the subwoofer may sound lower than other tones, in which
case adjust the level while listening to a source. Press ENTER when you’re finished.
49
En
LX03_En.book
09
50 ページ
2008年6月24日
火曜日
午後6時1分
Surround sound settings
Dynamic Range Control
Virtual Surround Back
When watching Dolby Digital or DTS material
at low volume, low level sounds — including
some of the dialog — can be difficult to hear
properly. Using one of the Dynamic Range
Control (DRC) settings can help by bringing up
the low level sounds, while controlling high
level peaks.
This mode allows you to use your surround
speakers with standard surround setup to
listen to a virtual surround back channel. You
can choose to listen to sources with no
surround back channel information, or if the
material sounds better in the format (for
example, 5.1) for which it was originally
encoded, you can have the unit only apply this
effect to 6.1 encoded sources like Dolby Digital
EX or DTS-ES.1
Dynamic Range Control works only with Dolby
Digital soundtracks and some DTS
soundtracks.
SETUP
1
menu.
SETUP
ENTER
Open the ‘Sound Setup’
1
menu.
Select ‘D.R.C.’, then press ENTER.
2
ENTER.
ENTER
Open the ‘Sound Setup’
ENTER
ENTER
2
3
Select a setting.
Select one of the following:
• D.R.C. High – Dynamic range is reduced
(loud sounds are reduced in volume while
quieter sounds are increased)
3
Select a setting.
Select one of the following:
• Vir.SB On – Virtual Surround Back is
always used (for example, on 5.1 encoded
material).
• D.R.C. Mid – Mid setting
• D.R.C. Off – No dynamic range adjustment
(use when listening at higher volume)
4
ENTER
Press to exit.
Select ‘Virtual SB’, then press
• Vir.SB Off – Virtual Surround Back mode
is switched off.
The V.SB indicator lights when Virtual
Surround Back is active.
4
ENTER
Press to exit.
Note
1 • Depending on the input signal and the listening mode, the Virtual Surround Back mode may not be effective.
• The Virtual Surround Back mode is not effective when the headphones are connected or when using the Front surround
setup.
50
En
LX03_En.book
51 ページ
2008年6月24日
火曜日
午後6時1分
Surround sound settings
09
DTS CD setting
Some Dolby Digital and DTS audio sources
include ultra-low bass tones.
If you play a DTS-encoded CD, you will need to
change this setting to hear the decoded signal.
Set the LFE attenuator as necessary to prevent
the ultra-low bass tones from distorting the
sound from the speakers.
ENTER
Open the ‘Sound Setup’
ENTER
Open the ‘Sound Setup’
ENTER
2
ENTER.
Select ‘CD Type’, then press
Select ‘LFE ATT’, then press
3
Select a setting.
Select one of the following:
• 0dB – The LFE is not limited, which is the
recommended value.
• DTS-CD – Use for playback of DTSencoded CDs, but note that the beginning
of regular CD tracks may be skipped.
• LFE Off – No sound is output from the LFE
channel.
4
ENTER
Press to exit.
Dual mono setting
4
ENTER
Press to exit.
Español
Specifies how dual mono encoded Dolby
Digital soundtracks should be played. This
setting can also be used to change the audio
channels for DVD-RW discs recorded in
bilingual audio, and external inputs with
bilingual audio (HDMI and optical/coaxial
digital inputs).
Nederlands
• -10dB – The LFE is limited by the respective
degree.
Italiano
• Normal CD – Use for playback of regular
audio CDs. Some DTS-encoded CDs will
output noise when played.
3
Select a setting.
Select one of the following:
Français
ENTER
2
ENTER.
Deutsch
SETUP
1
menu.
SETUP
1
menu.
English
LFE Attenuate
AUDIO
1
Press repeatedly to select a setting.
Select one of the following:1
• CH1 Mono – Only channel 1 is played
• CH2 Mono – Only channel 2 is played
• CH1/CH2 – Both channels are played
through the front speakers
Note
1 When DVD function is selected, the displayed setting items are L, R and L+R (displayed on OSD).
51
En
LX03_En.book
10
52 ページ
2008年6月24日
火曜日
午後6時1分
Video Adjust menu
Chapter 10
Video Adjust menu
Video Adjust menu
From the Video Adjust screen you can adjust
settings that affect picture presentation.
HOME MENU
1
ENTER
Video Adjust
ENTER
3
Make settings.
Video Adjust
Sharpness
Brightness


Standard
0
Contrast
Gamma


0
Off
Hue
Chroma Level


0
0
You can adjust the following settings:
• Sharpness – Adjusts the sharpness of
edges in the picture (Fine, Standard,
Soft).
• Brightness – Adjusts the overall
brightness (–20 to +20).
• Contrast – Adjusts the contrast between
light and dark (–16 to +16).
• Gamma – Adjusts the ‘warmth’ of the
picture (High, Medium, Low, Off).
• Hue – Adjusts the red/green balance
(Green 9 to Red 9).
• Chroma Level – Adjusts how saturated
colors appear (–9 to +9).
En
Brightness
ENTER
Press HOME MENU.
2
Select ‘Video Adjust’ from the onscreen display.
52
Adjust the Brightness, Contrast, Hue and
Chroma Level settings using /.
min
max
0
4
Press to return to the Video Adjust
screen, or press HOME MENU to exit.
LX03_En.book
53 ページ
2008年6月24日
火曜日
午後6時1分
Initial Settings menu
11
English
Chapter 11
Initial Settings menu
Using the Initial Settings menu
ENTER
CD
DVD
Press DVD.
Initial Settings
ENTER
4
Select the setting and option you
want to set.
All the settings and options are explained on
the following pages.1
Français
1
Select ‘Initial Settings’.
Deutsch
The Initial Settings menu provides audio and
video output settings, parental lock settings,
and display settings, among others.
If an option is grayed out it means that it
cannot be changed at the current time. This is
usually because a disc is playing. Stop the
disc, then change the setting.
3
HOME MENU
Italiano
2
With playback stopped, press to
display the Home Menu.
Option
What it means
TV Screen
(See also Screen sizes
and disc formats on
page 77.)
4:3 (Letter Box)
Set if you have a conventional 4:3 TV. Widescreen movies are
shown with black bars top and bottom.
4:3 (Pan & Scan)
Set if you have a conventional 4:3 TV. Widescreen movies are
shown with the sides cropped so that the image fills the screen.
16:9 (Wide)
Set if you have a widescreen TV.
16:9 (Compressed)
Can be selected when the HDMI Resolution is set to 1920 x
1080p, 1920 x 1080i or 1280 x 720p. Video in 4:3 can be
properly displayed on a 16:9 high definition television (with
black bars shown on either side of the screen).
AV Connector Out
Video
(See Connecting
S-Video
auxiliary components on
page 59.)
RGB
Español
Setting
Nederlands
Video Output settings
Ordinary (composite) video output, compatible with all TVs.
Almost the same quality as RGB, but can give better results if
you are using a long SCART cable.
If your TV is compatible, this setting gives the best picture
quality.
Note
1 • In the table, the default setting is shown in bold: other settings are shown in italics.
• Some settings, such as TV Screen, Audio Language and Subtitle Language may be overridden by the DVD disc. Often
these settings can also be made from the DVD disc menu.
• The AV Connector Out setting only needs to be set if you have connected this unit to your TV using a SCART cable.
53
En
LX03_En.book
11
54 ページ
2008年6月24日
火曜日
午後6時1分
Initial Settings menu
Setting
Option
What it means
HDMI Resolution*
(See Connecting using
HDMI on page 62.)
* Default changes with
TV format (PAL/NTSC).
1920x1080p
Set if your TV supports 1920 x 1080 pixel progressive-scan video.
1920x1080i
Set if your TV supports 1920 x 1080 pixel interlace video.
HDMI Color*
(See Connecting using
HDMI on page 62.)
* Default changes
depending on device
connected.
1280x720p
Set if your TV supports 1280 x 720 pixel progressive-scan video.
720x480p (NTSC)/
720x576p (PAL)
Set if your TV supports 720 x 480 (NTSC)/720 x 576 (PAL) pixel
progressive-scan video.
Full range RGB
If colors are weak, this gives brighter colors and deeper black
(default setting for HDMI-compatible DVI devices).
RGB
Use this setting if colors appear overly rich on the Full Range
RGB setting.
Component
Outputs 8-bit component video format (default setting for
HDMI-compatible devices).
Language settings1
Setting
Option
What it means
Audio Language
English
If there is an English soundtrack on the disc, it is played.
Languages as displayed
If there is a language selected on the disc, it is played.
Other Language
Select to choose a language other than the ones displayed (see
Language code list on page 85).
English
If there are English subtitles on the disc they are displayed.
Subtitle Language
DVD Menu
Lang.
Subtitle Display
Languages as displayed
The subtitle language selected on the disc is displayed.
Other Language
Select to choose a language other than the ones displayed (see
Language code list on page 85).
w/Subtitle Lang.
DVD disc menus are displayed in the same language as your
selected subtitle language, if possible.
Languages as displayed
DVD menus are displayed in the selected language, if possible.
Other Language
Select to choose a language other than the ones displayed (see
Language code list on page 85).
On
Subtitles are displayed in your selected subtitle language.
Off
Subtitles are always off by default when you play a DVD disc.
Note
1 When you have this unit connected to an HDMI Control compatible Pioneer flat screen TV, language settings are imported
from the flat screen TV’s OSD settings before HOME MENU or Disc Navigator begins.
54
En
LX03_En.book
55 ページ
2008年6月24日
火曜日
午後6時1分
Initial Settings menu
11
Setting
Option
What it means
OSD Language
English
On-screen displays of the player are in English.
Languages as displayed
On-screen displays are shown in the language selected.
On
A camera icon is displayed on-screen during multi-angle
scenes on a DVD disc.
Off
No multi-angle indication is shown.
Options settings
Option
What it means
Parental Lock
–
See Parental Lock below.
DVD Playback
Only the DVD-Video part of a DVD-Audio disc is playable.
2ch Area
Selects the 2 channel (stereo) SACD audio area of the disc
for playback.
Multich Area
Selects the multichannel SACD audio area of the disc for
playback.
CD Area
Selects the standard CD audio area of an SACD/CD hybrid
disc for playback.
Display
See About DivX® VOD content on page 56.
Parental Lock
• Default level: Off; Default password: none;
Default Country/Area code: us (2119)
Some discs also support the Country/Area
Code feature. The player does not play certain
scenes on these discs, depending on the
Country/Area Code you set.
Register a password to change the Parental
Lock level or enter a Country/Area code.1
ENTER
1
ENTER.
Select ‘Password’ then press
Español
To give you some control over what your
children watch on your DVD player, some DVDVideo discs feature a Parental Lock level. If your
player is set to a lower level than the disc, the
disc won’t play.
Registering a new password
Nederlands
DivX(R) VOD
All material on a DVD-Audio disc is playable.
Italiano
SACD Playback
DVD-Audio
DVD-Video
Français
Setting
Deutsch
Angle Indicator
English
Display settings
Initial Settings
Video Output
Language
Parental Lock
DVD Playback
Password
Level Change
Display
Options
SACD Playback
DivX (R) VOD
Country Code
Note
1 • Not all discs use Parental Lock, and will play without requiring the password.
• If you forget your password, you’ll need to reset the player to register a new password (see Resetting the system on page 84).
55
En
LX03_En.book
11
56 ページ
2008年6月24日
火曜日
午後6時1分
Initial Settings menu
1
2
3
4
5
6
7
8
9
0
2
Input a four-digit password
then press ENTER.
CLEAR
Changing your password
To change your password, confirm your
existing password then enter a new one.
About DivX® VOD content
In order to play DivX VOD (video on demand)
content on this player, you first need to register
the player with your DivX VOD content
provider. You do this by generating a DivX VOD
registration code, which you submit to your
provider.1
1 Select ‘Password Change’, input your
existing password, then press ENTER.
2
Important
• DivX VOD content is protected by a DRM
(Digital Rights Management) system. This
restricts playback of content to specific,
registered devices.
Enter a new password and press ENTER.
Setting/changing the Parental Lock
1
Select ‘Level Change’ then press ENTER.
2
Enter your password, then press ENTER.
3
Select a new level and press ENTER.
• Press  repeatedly to lock more levels
(more discs will require the password);
press  to unlock levels. You can’t lock
level 1.
Setting/changing the Country/Area code
You can find the Country/Area code list on
page 85.
1 Select ‘Country Code’, input your
password, then press ENTER.
2 Select a Country/Area code then press
ENTER.
There are two ways you can do this:
• Select by code letter: Use / to change
the Country/Area code.
• Select by code number: Press  then use
the number buttons to enter the four-digit
Country/Area code.
• If you load a disc that contains DivX VOD
content not authorized for your player, the
message Authorization Error is displayed
and the content will not play.
Displaying your DivX VOD registration
code
1 Press HOME MENU and select ‘Initial
Settings’.
2
Select ‘Options’, then ‘DivX (R) VOD’.
Initial Settings
Video Output
Language
Display
Options
Parental Lock
DVD playback
SACD playback
DivX (R) VOD
3 Select ‘Display’.
Your eight-digit registration code is displayed.
Make a note of the code as you will need it
when you register with a DivX VOD provider.
The new Country/Area code takes effect after
ejecting the disc once.
Note
1 Resetting the system (as described in page 84) will not cause you to lose your registration code.
56
En
Display
LX03_En.book
57 ページ
2008年6月24日
火曜日
Initial Settings menu
Français
If your DivX VOD content allows an unlimited
number of plays, then you may load the disc
into your player and play the content as often
as you like, and no message will be displayed.
Deutsch
Some DivX VOD content may only be playable
for a fixed number of times. When you load a
disc containing this type of DivX VOD content,
the remaining number of plays is shown onscreen and you then have the option of playing
the disc (thereby using up one of the remaining
plays), or stopping. If you load a disc that
contains expired DivX VOD content (for
example, content that has zero remaining
plays), the message Rental Expired is
displayed.
11
English
Playing DivX® VOD content
午後6時1分
Italiano
Nederlands
Español
57
En
LX03_En.book
12
58 ページ
2008年6月24日
火曜日
午後6時1分
Other connections
Chapter 12
Other connections
• When digital connections are used, it may
be necessary to adjust the digital audio
output settings on the TV. For details,
consult the operating instructions for your
TV.
Important
• When making or changing connections on
the rear panel of this unit, be sure to switch
power off and disconnect the power cord
from the wall socket.
After completing all connections, connect
the power cord to the wall socket.
Using this unit for TV audio
To listen to audio from a TV, connect the TV’s
audio cable to one of the inputs on this unit.
TV
From analog output
From digital output
(coaxial)
Audio input settings from the TVs
(TV Input)
To listen to audio from a flat screen TV on this
device, you will need to connect an audio cable
other than an HDMI cable. From this menu, set
the audio input to that which you would like to
connect. Press TV on the remote control to
switch this unit to the input source selected
here. This setting is changed to the selected
input and the audio from the flat screen TV is
output from this device.
Select from inputs Digital 1 OPT, Digital 2
OPT, Digital 3 COAX, Analog 1 RCA and
Analog 2 SCART.
(optical)
SETUP
1
Press SETUP.
ENTER
ANALOG
1
L
OPTICAL
R
AV CONNECTOR
VIDEO OUT
AUDIO IN
3
COAX
DIGITAL IN
ANALOG 2
1 AM
LOOP
OUT
IN 2
ANTENNA
IN 1
• To use the HDMI Control function when
you are connected to a supported Pioneer
flat screen TV, you must connect via HDMI.
En
Select ‘System Setup’ then press
FM
2 UNBAL
75
DIGITAL IN
HDMI
• Connect the audio output jacks on your
TV to the audio input jacks on the receiver.
• You can connect by either a digital or
analog audio cable. Select only one
method to make connections.
58
2
ENTER.
ENTER
3
ENTER.
Select ‘TV Input’, then press
ENTER
4
Adjust the setting then press
ENTER to confirm.
LX03_En.book
59 ページ
2008年6月24日
火曜日
午後6時1分
Other connections
12
We recommend using an HDMI cable to
connect sources that have HDMI terminals.
For more information see Connecting using
HDMI on page 62.
You can use the ANALOG AUDIO IN jacks to
connect an analog audio component, such as
a tape player.
Deutsch
You can connect both analog and digital
external audio sources to this system. Digital
audio sources include digital satellite
receivers, CD recorders, etc.
Tape player, etc.
From
analog output
Français
Connecting for digital audio
This system has several digital inputs for digital
playback components, such as your MD or CD
recorder.
ANALOG
1
L
R
ANALOG
HDMI
OUT
IN 2
IN 1
Nederlands
From digital
output (optical)
or
ANALOG 2
Italiano
MD, CD recorder, etc.
AV CONNECTOR
VIDEO OUT
AUDIO IN
3
COAX
DIGITAL IN
From digital
output (coaxial)
English
Connecting an analog audio
component
Connecting auxiliary
components
1
L
OPTICAL
R
AV CONNECTOR
VIDEO OUT
3
COAX
DIGITAL IN
ANALOG 2
1 AM
LOOP
FM
2 UNBAL
75
DIGITAL IN
HDMI
OUT
IN 2
ANTENNA
IN 1
• Connect the digital output jack on CD
recorder, etc. to one of the DIGITAL input
jacks on this unit.
Use a commercially available optical cable or
coaxial cable to make this connection.
Español
AUDIO IN
These include digital components such as an
MD player, digital satellite, or a game system.
• When digital connections are used, it may be
necessary to adjust the digital audio output
settings on the connected component. For
details, consult the operating instructions for
the component involved.
59
En
LX03_En.book
12
60 ページ
2008年6月24日
火曜日
午後6時1分
Other connections
Using the SCART AV connector
The SCART output should give you better
picture quality than the standard composite
video output. The SCART AV connector
functions as both a video and audio output.1
SCART pin assignment
The diagram below shows the SCART 21-pin
connector assignment. This connector
provides the video and audio signals for
connection to a compatible color TV/monitor.
• Use a commercially available SCART cable
to connect the (LINE 1) AV CONNECTOR to
your TV.
To SCART
input
Pin No. Assignment
Pin No. Assignment
1
Audio R OUT
12
No connection
2
Audio R IN
13
GND (video)
3
Audio L OUT
14
GND (video)
4
GND (audio)
15
R or C OUT
5
GND (video)
16
BLANK OUT
6
Audio L IN
17
GND (video)
7
B OUT
18
GND (video)
8
Status
19
Video or Y OUT
9
GND (video)
20
No connection
10
No connection
21
GND (video)
11
G OUT
TV
ANALOG
1
L
OPTICAL
R
AV CONNECTOR
VIDEO OUT
AUDIO IN
3
COAX
DIGITAL IN
ANALOG 2
1 AM
LOOP
FM
2 UNBAL
75
DIGITAL IN
HDMI
OUT
IN 2
IN 1
ANTENNA
Line Output setting
Use to select the audio down-mix method
when outputting Dolby Digital multi-channel
sound sources from the AUDIO OUT jacks or
AV CONNECTOR.2
SETUP
1
Press SETUP.
Note
1 • SCART cables are available in several configurations. Make sure that the one you get will work with this system and your TV/
monitor (see SCART pin assignment below).
• If the TV’s SCART connector is a dual input/output connector, a single SCART cable can be used to input the television sound
to this unit. To listen to that sound, select Analog 2 SCART.
2 • When the Line Output is switched to Lt/Rt, the sound function will be fixed at the current setting and cannot be changed.
The display will briefly flash Line Out Mode if an attempt is made to use a prohibited function.
• When the Line Output is to Lo/Ro(Stereo), the audio from the analog output jacks may be interrupted, depending on the
operation.
• When using DTS multi-channel sound sources, output is in Lo/Ro(Stereo).
60
En
LX03_En.book
61 ページ
2008年6月24日
火曜日
午後6時1分
Other connections
Select ‘Sound Setup’, then press
ENTER
Select ‘Line Output’, then press
Digital 1 OPT
Analog 2 SCART
Digital 2 OPT
Analog 1 RCA
Digital 3 COAX
• Lo/Ro(Stereo) – A simple stereo downmix
(left-only/right-only, or Lo/Ro) is output
(suitable for playback on a two-channel
stereo system or on headphones).
Connecting external antennas
For an external AM antenna, use 5 to 6 meters
of vinyl-insulated wire and set up either indoors
or outdoors. Leave the loop antenna
connected.
For an external FM antenna, use a PAL
connector to hook up an external FM antenna.
Nederlands
External AM antenna
5
ENTER
Press to exit.
To listen to audio from a connected external
component on this system, choose its input
function on the remote control. Some Pioneer
products can be controlled via this remote.
Outdoor antenna
Indoor antenna
(vinyl-coated Wire)
External
FM antenna
(5 m to 6 m)
Español
Listening to an external audio
source
Italiano
• Lt/Rt – A surround-compatible downmix
(left-total/right-total, or Lt/Rt) of Dolby
multichannel sources is output, (suitable
for Dolby Surround Pro Logic or other
matrix decoding).
The L.OUT indicator lights.
3 If necessary, start playback of the
external source.
Français
4
Select a setting.
Select one of the following:
Deutsch
3
ENTER.
2 LINE Select an audio input source.
Input sources are cycled through as shown
below:
English
ENTER
2
ENTER.
12
AM Loop antenna
STANDBY / ON
 If the system isn’t already on,
1
switch it on.
Also make sure that the external source (TV,
satellite receiver, etc.) is switched on.
OPTICAL
1 AM
LOOP
FM
2 UNBAL
75
DIGITAL IN
ANTENNA
PAL connector
61
En
LX03_En.book
12
62 ページ
2008年6月24日
火曜日
午後6時1分
Other connections
About control out connections
Connecting using HDMI
Many Pioneer components support CONTROL
connections, by which you can use the remote
controls of any connected components by
aiming them at the sensor of just one
component.
If you have a HDMI or DVI (with HDCP)
equipped monitor or display, you can connect
it to this system using a commercially available
HDMI cable for high quality digital video.1
When you use a remote control, the control
signal is passed along the chain to the
appropriate component.
See About HDMI on page 64 for more about the
HDMI connection.
If you choose to use this feature, you must
make sure that you also have at least one set of
HDMI or analog audio jacks connected to
another component for grounding purposes.
• Using a cable with a mono mini-plug on
either end, connect the CONTROL IN jack on
another Pioneer component to the CONTROL
OUT jack on the rear panel.
This will allow you to control the other
component by pointing its remote at the front
panel.
TV
To HDMI input
OPTICAL
AV CONNECTOR
EO OUT
ANALOG 2
1 AM
LOOP
FM
2 UNBAL
75
DIGITAL IN
HDMI
OUT
IN 2
ANTENNA
IN 1
From HDMI output
HDMI/DVI-equipped component
Note
1 • An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High Bandwidth
Digital Content Protection (HDCP). If you choose to connect to a DVI connector, you will need a separate adaptor (DVIHDMI)
to do so. A DVI connection, however, does not support audio signals. Consult your local audio dealer for more information.
• This system has been designed to be compliant with HDMI (High-Definition Multimedia Interface).
• When HDMI Audio is set to TV, sound is output from this unit to the TV connected to the HDMI connectors in for audio format
supported by that TV.
• Depending on the component you have connected, using a DVI connection may result in unreliable signal transfers.
62
En
LX03_En.book
63 ページ
2008年6月24日
火曜日
午後6時1分
Other connections
Switching the HDMI audio setting
Specifies the routing of the HDMI audio signal
out of this system (amp) or through to a TV or
flat screen TV. You cannot use a number of
sound functions of this system when HDMI
audio is set to TV.
2 Use an HDMI cable to connect the HDMI
OUT interconnect on this system to an HDMI
interconnect on an HDMI-compatible display.
ENTER
2
ENTER.
Select ‘HDMI Setup’ then press
ENTER
3
ENTER.
Select ‘HDMI Audio’, then press
• TV – Output an HDMI audio signal from a
TV or flat screen TV.1
Español
• If the video signal does not appear on your
TV or flat screen TV, try adjusting the
resolution settings on your component or
display.
Nederlands
• Set the HDMI Audio setting to TV in
Switching the HDMI audio setting below if
you want to hear HDMI audio output from
your TV or flat screen TV (no sound will be
heard from this unit).
ENTER
4
Adjust the setting then press
ENTER to confirm.
• AMP – Output an HDMI audio signal from
this system.
Italiano
1/2
3 HDMI Press repeatedly to select the HDMI
input you’ve connected to (for example,
HDMI 2).
You can also use the front panel FUNCTION to
carry out this operation.
Français
Once this system is properly connected to your
HDMI component, the HDMI indicator (red)
lights up on the front panel when you watch
HDMI contents.
Press SETUP.
Deutsch
SETUP
1
English
1 Use an HDMI cable to connect the HDMI
IN 1/2 interconnect on this system to an HDMI
output on your HDMI component.
• With the arrow on the cable plug facing up,
connect the plug to the player’s connector.
12
Note
1 This makes it possible to use the TV’s built-in speakers to listen to the audio input from a DVD, iPod (44.1kHz only), USB device
or HDMI 1/2 component. In this event, no sound will be heard from this unit’s speakers (or headphones). All other audio sources
(including TUNER) are output from this unit normally.
63
En
LX03_En.book
12
64 ページ
2008年6月24日
火曜日
午後6時1分
Other connections
Setting the Auto Delay
This feature automatically corrects the audioto-video delay between components connected
with an HDMI cable. The audio delay time is set
depending on the operational status of the
display connected with an HDMI cable. The
audio delay time is automatically adjusted
according to the video delay time.
ENTER
2
ENTER.
Select ‘Initialize’ then press
ENTER
3
Select ‘HDMI Init’ then press
ENTER.
• Initialize OK? is displayed.
SETUP
1
Press SETUP.
ENTER
Select ‘HDMI Setup’ then press
2
ENTER.
About HDMI
ENTER
Select ‘Auto Delay’, then press
3
ENTER.
ENTER
4
Select ‘A.Delay On’ or ‘A.Delay
Off’ then press ENTER to confirm.
Tip
• This feature is only available when the
connected display supports the automatic
audio/video synchronizing capability (‘lipsync’) for HDMI or HDMI Control. If you
find the automatically set delay time
unsuitable, set A.Delay to Off and adjust
the sound delay settings manually
(page 31).
Resetting the HDMI connection
If the screen goes blank (for example, after
changing the resolution), check the
troubleshooting guide on (page 82). If this
doesn’t solve the problem, follow the steps
below to reset the HDMI connection.
SETUP
1
64
En
4 ENTER Press ENTER to confirm initialization.
The system will restart and the HDMI settings
are automatically reset to the factory defaults.
See Video Output settings on page 53 for more
on these settings.
Press SETUP.
HDMI (High-Definition Multimedia Interface)
supports both video and audio on a single
digital connection for use with DVD players,
DTV, set-top boxes, and other AV devices.
HDMI was developed to provide the
technologies of High-bandwidth Digital
Content Protection (HDCP) as well as Digital
Visual Interface (DVI) in one specification.
HDCP is used to protect digital content
transmitted and received by DVI-compliant
displays.
HDMI has the capability to support standard,
enhanced, or high-definition video plus standard to multichannel surround-sound audio.
HDMI features include uncompressed digital
video, a bandwidth of up to 2.2 gigabytes per
second (with HDTV signals), one connector
(instead of several cables and connectors), and
communication between the AV source and
AV devices such as DTVs.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
LX03_En.book
65 ページ
2008年6月24日
火曜日
午後6時1分
HDMI Control
13
English
Chapter 13
HDMI Control
• The KURO LINK function name used on
the web and in catalogues is referred to as
HDMI Control in the operating instructions
and on the product.
• HDMI Control may not operate properly if
you do not use a High Speed HDMI cable.
• Requires connection of audio cables and
additional settings. For details see Audio
input settings from the TVs (TV Input) on
page 58.
HDMI Control-compatible
Pioneer flat screen TV
From
analog output
From optical digital
output (or coaxial)
To
HDMI input
Nederlands
Español
Refer to the operating instructions for your flat
screen TV for more information about which
operations can be carried out by connecting
via HDMI cable.
Be sure to connect the flat screen TV’s audio
cable to the audio input of this unit.
Italiano
In addition, when language information is
input from the connected flat screen TV, this
unit’s GUI display language automatically
changes (only when playback is stopped and
GUI screen is not displayed, with DVD/CD
function only).
You can use synchronized operation for a
connected flat screen TV and up to two other
components (including a recorder or player).
Français
By connecting this unit to an HDMI Controlcompatible Pioneer flat screen TV or the HDD/
DVD recorder with an HDMI cable, you can
control this unit from the remote control of a
connected flat screen TV, as well as have the
connected flat screen TV automatically change
inputs in response to operations carried out on
this unit.
Making the HDMI Control
connections
Deutsch
Important
• You cannot use this function with
components that do not support HDMI
Control.
ANALOG
• We cannot guarantee this unit will work
with HDMI Control-compatible components
other than those made by Pioneer.
1
L
OPTICAL
R
AV CONNECTOR
VIDEO OUT
1 AM
LO
ANALOG 2
AUDIO IN
3
COAX
DIGITAL IN
FM
2 UM
75
DIGITAL IN
HDMI
OUT
IN 2
IN 1
From HDMI output
HDMI Control-compatible
Pioneer HDD/DVD recorder
Blu-ray disc player or DVD player
65
En
LX03_En.book
13
66 ページ
2008年6月24日
火曜日
午後6時1分
HDMI Control
• Connect the flat screen TV directly to this
unit. Interrupting a direct connection with
other amps or an AV converter (such as an
HDMI switch) can cause operational
errors.
• Only connect components you intend to use
as a source to the HDMI input of this unit.
Interrupting a direct connection with other
amps or an AV converter (such as an HDMI
switch) can cause operational errors.
HDMI Control-compatible
Pioneer flat screen TV
HDMI Control-compatible
Pioneer flat screen TV
HDMI input
HDMI input
HDMI cable
HDMI output
HDMI cable
HDMI OUT
PULL OPEN
HDMI input
Other amps
or AV converter
STANDBY / ON
HDMI
HDMI IN
HDMI cable
HDMI OUT
HDMI cable
HDMI output
PULL OPEN
STANDBY / ON
This unit
HDMI
This unit
Other amps
or AV converter
Important
• When connecting this system or changing
connections, be sure to switch the power
off and disconnect the power cord from the
wall socket.
After completing all connections, connect
the power cords to the wall socket.
• After connecting this unit to an AC outlet, a
15-second initialization process begins.
You cannot carry out any operations during
initialization. The HDMI indicator on the
front panel blinks during initialization, and
you can turn this unit on once it has
stopped blinking.
• To get the most out of this function, we
recommend that you connect your HDMI
component not to a flat screen TV but
rather directly to the HDMI terminal on this
unit.
66
En
LX03_En.book
67 ページ
2008年6月24日
火曜日
午後6時1分
HDMI Control
13
Before using synchronization
You must adjust the settings of this unit as well
as HDMI Control-compatible connected
components in order to make use of the HDMI
Control function. For more information see the
operating instructions for each component.
Once you have finished all connections and
settings, you must:
• When using a TV not manufactured by
Pioneer, put this setting to Control Off.
2 Turn the power ON for all components,
with the power for the flat screen TV being
turned on last.
3 Choose the HDMI input to which the TV is
connected to this unit, and see if video
output from connected components displays
properly on the screen or not.
Français
Choose whether to set this unit’s HDMI Control
function On or Off. You will need to set it to
Control On to use the HDMI Control function.
Put all components into standby mode.
Deutsch
Setting the HDMI Control mode
1
English
Setting the HDMI options
SETUP
1
Press SETUP.
Select ‘HDMI Setup’ then press
Select ‘HDMI Ctrl’, then press
Nederlands
ENTER
3
ENTER.
Italiano
ENTER
2
ENTER.
ENTER
Español
4
Adjust the setting then press
ENTER to confirm.
• Control On – Enables the HDMI Control
function. When this unit’s power is turned
off and you have a supported source begin
playback while using the HDMI Control
function, the audio and video output from
the HDMI connection are output from the
flat screen TV.
• Control Off – The HDMI Control is
disabled. Synchronized operations cannot
be used. When this unit’s power is turned
off, audio and video of sources connected
via HDMI are not output.
67
En
LX03_En.book
13
68 ページ
2008年6月24日
火曜日
HDMI Control
Synchronized amp mode
Synchronized amp mode begins once you
carry out an operation for the flat screen TV. For
more information, see the operating
instructions of your flat screen TV.
Synchronized amp mode operations
The synchronized amp mode can be used to
perform the following operations when using
the internal DVD/CD player, USB or iPod
function, or when the HDMI cable is used to
connect an external component:
• Displays on the flat screen TV when you
mute or adjust the volume of this unit.
• The input of this unit is automatically
changed when playback occurs on a
connected component.
• Even if you change this unit’s input to a
device that is not connected by HDMI, the
synchronized amp mode remains in effect.
Canceling synchronized amp mode
If you cancel synchronized amp mode while
connected via HDMI to a flat screen TV or while
you are watching a TV program, the power for
this unit is turned off.
However, the power remains ON when an input
other than HDMI is selected (including internal
DVD/CD, USB, or iPod function).
68
En
午後6時1分
LX03_En.book
69 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
14
Additional information
SETUP
1
Press SETUP.
ENTER
2
Adjust the setting, then press
ENTER to confirm the settings and exit.
• Sleep On – Switches off after about an
hour. The
indicator lights.
• Sleep Off – Cancels the sleep timer.
After selecting Sleep On, you can press SLEEP
again to check how much time is left. Each line
indicates approximately 12 minutes
(remaining):
Français
All the available settings in the System Setup
menu are listed below. See the notes in each
section for more information about the
settings. The first setting in each section is the
default.
Deutsch
Optional system settings
English
Chapter 14
ENTER
Sleep --- --
Select ‘System Setup’ then press
Dimming the display
ENTER
You can adjust the brightness of the text in the
front panel display.3
ENTER
1
Select ‘Dimmer’ from the System
Setup menu, then press ENTER.
Nederlands
3
Choose the setting you want to
adjust, then press ENTER.
The available settings are shown in the front
panel display.1
Italiano
2
ENTER.
ENTER
Setting the sleep timer
The sleep timer switches off the system after
about an hour so you can fall asleep without
worrying about it.2
ENTER
2
Adjust the setting, then press
ENTER to confirm the settings and exit.
• Dimmer Light – Brighter setting
Español
4
Adjust the setting, then press
ENTER to confirm the settings and exit.
• Dimmer Dark – Darker setting
ENTER
1
Select ‘Sleep Timer’ from the
System Setup menu, then press ENTER.
Note
1 The setup menu is exited automatically after 5 minutes of inactivity.
2 The display dims when the sleep timer is set.
3 The display of the front panel dims when the sleep timer is set, regardless of this setting.
69
En
LX03_En.book
14
70 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
Changing the display mode
If no operation is performed for one minute, the
front panel display and button illumination
automatically turns off. The display will turn on
again automatically if a command is input or
movement is detected by the motion sensor.
To make the display remain on constantly, set
the display mode to Display On.
ENTER
1
Select ‘Display Mode’ from the
System Setup menu, then press ENTER.
• Lock Off – Restores regular use of the front
panel buttons and controls.
TV system setting
The default setting of this system is Auto, and
unless you notice that the picture is distorted
when playing some discs, you should leave it
set to Auto. If you find picture distortion with
some discs, set the TV system to match your
country or region’s system. However, this may
restrict the kinds of disc you can watch. See
the table for the kinds of discs compatible with
each setting (Auto, PAL and NTSC).1
ENTER
2
Adjust the setting, then press
ENTER to confirm the settings and exit.
• Auto Display – Turns off automatically if
no operation is performed for one minute.
• Display On – Displays constantly.
Even when set to not display, the display is
temporarily shown when you carry out a
control function.
• The motion sensor detects movement in
the left/right and up/down directions
within a distance of 2.5 m and an angle of
40º (20º only in the upper direction).
Walking towards the unit will reduce the
sensing range to 0.7 m.
Key lock setting
ENTER
1
Select ‘Key Lock’ from the System
Setup menu, then press ENTER.
ENTER
ENTER
1
Select ‘TV System’ from the
System Setup menu, then press ENTER.
• Change TV SYS? is displayed.
ENTER
2
Press ENTER to confirm.
Change the TV system as follows:
• Auto  NTSC
• NTSC  PAL
• PAL  Auto
The system will automatically enter standby
mode, then turn ON once again. You will see
the new TV system setting in the display after
seeing Power On.
Player setting
Media Type
DVD/Super VCD/
Video CD/DivX
Video/WMV
CD/MP3/WMA/
MPEG-4 AAC/
JPEG/no disc
Format NTSC
PAL
Auto
NTSC
NTSC
PAL
NTSC
PAL
NTSC
PAL
PAL
—
NTSC
PAL
NTSC or
PAL
2
Adjust the setting, then press
ENTER to confirm the settings and exit.
• Lock On – Makes the front panel buttons
and controls inoperative.
Note
1 Most models of the newly developed countdown PAL TV system detect 50 Hz (PAL)/60 Hz (NTSC) and automatically switch
vertical amplitude, resulting in a display without vertical shrinkage. However, in some cases, the image may appear without
color. If your PAL TV does not have a V-Hold control, you may not be able to watch NTSC discs because of picture roll. If the TV
has a V-Hold control, adjust it until the picture stops rolling. On some TVs, the picture may shrink vertically, leaving black bands
at the top and bottom of the screen.
70
En
LX03_En.book
71 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
1
2
3
4
5
6
7
8
9
CLEAR
Nederlands
2 Point the remote towards your TV and
press TV Control  to check that the remote
works with your TV.
If the remote is set up correctly, the TV should
switch off. If it doesn’t and there is another
code given for your maker, repeat step 1 with a
new code.
Español
Aiwa 660
Alba 639
Bush 647
Fisher 635, 638
Fujitsu 648
Funai 640, 658
GE 611, 628
General 629
Goldstar 610, 623, 650
Grandiente 630
Grundig 631, 653
Hitachi 606, 624, 625, 633, 634, 654
ITT 642
JVC 613
Magnabox 612
Mitsubishi 609
NEC 659
Nokia 632, 652
Panasonic 608, 622
Philips 607, 656, 668
RCA 601, 615, 616, 617, 618, 661, 662
Salora 643
Samsung 644, 646, 669, 670
Sanyo 614, 621, 645
SEI 649
Sharp 602, 619, 627, 667
Sony 604
Tandy 641
Telefunken 637
Thomson 636, 663
Toshiba 605, 626
Uniden 671
Zenith 603, 620
Pioneer 600, 651
Italiano
• If the maker’s name of your TV doesn’t
appear in the table, you will not be able to
use this remote to control your TV.
Manufacturer Code(s)
Français
0
1
Press and hold CLEAR and Use
the number buttons to input the maker code
for your TV, and press ENTER.
See the following table for the list of maker
codes. If there is more than one code given for
your make, input the first one in the list.
Please note that there are cases where only
certain functions may be controllable after
assigning the proper preset code, or the codes
for the manufacturer in the list will not work for
the model that you are using.
Deutsch
You can use the supplied remote to control
your TV. To be able to use this feature you first
have to program the remote with a maker code
from the following table.
TV Preset code list
English
Setting up the remote to control
your TV
14
71
En
LX03_En.book
14
72 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
Surround sound formats
Below is a brief description of the main
surround sound formats you’ll find on DVDs,
satellite, cable and terrestrial broadcasts, and
video cassettes.
Dolby
The Dolby technologies are explained below.
See www.dolby.com for more detailed
information.
• Dolby Pro Logic II – 5.1 channel sound
(stereo surround) from any stereo source
With two channel sources, the “.1” subwoofer
channel is generated by bass management in
the receiver.
Dolby Surround is an encoding system which
embeds surround sound information within a
stereo soundtrack, which a Dolby Pro Logic
decoder can then use for enhanced surround
listening with greater sound detail.
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, and the double-D
symbol are trademarks of Dolby Laboratories.
DTS
The DTS technologies are explained below. See
www.dtstech.com for more detailed
information.
Dolby Digital
Dolby Digital is a multichannel digital audio
coding system widely used in cinemas, and in
the home for DVD and digital broadcast
soundtracks. It can deliver up to six discrete
audio channels, comprising five full range
channels and a special LFE (low frequency
effects) channel used mainly for deep,
rumbling sound effects; hence the term “5.1channel” Dolby Digital.
In addition to the format features above, Dolby
Digital decoders offer downmixing for
compatibility with mono, stereo and Dolby Pro
Logic audio from a number of bit rates and
channels. Another feature, called Dialog
Normalization, attenuates programs based on the
average level of dialog in a program relative to its
peak level (also known as Dialnorm) in order to
achieve uniform playback level.
Dolby Pro Logic II and Dolby Surround
Using the innovative “steering logic” circuit,
this system extracts surround sound from
sources as follows:
• Dolby Pro Logic – 4.1 channel sound
(mono surround) from any stereo source
72
En
DTS Digital Surround
DTS Digital Surround is a 5.1-channel audio
coding system from DTS Inc. now widely used
for DVD-Video, DVD-Audio, 5.1 music discs,
digital broadcasts, and video games. It can
deliver up to six discrete audio channels,
comprising five full range channels, including
an LFE channel. Higher sound quality is
achieved through the use of a low compression
rate, and high rates of transmittance during
playback.
LX03_En.book
73 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
Super Video CD (Super VCD)
About DualDisc playback
Please also note that recordable discs cannot be
recorded using this unit.
The DVD side of a DualDisc plays in this
product. DVD-Audio content will not play.
DVD-R
DVD-RW
CD-R/-RW compatibility
Video CD
CD-R
CD-RW
Super Audio CD
• Compatible formats: CD-Audio, Video CD/
Super VCD, ISO 9660 CD-ROM* containing
MP3, WMA, MPEG-4 AAC, JPEG or DivX
video/WMV files
* ISO 9660 Level 1 or 2 compliant. CD
physical format: Mode1, Mode2 XA Form1.
Romeo and Joliet file systems are both
compatible with this player.
Español
Audio CD
Nederlands
DVD-Video
For more detailed information on the DualDisc
specification, please refer to the disc
manufacturer or disc retailer.
Italiano
The non-DVD, audio side of the disc is not
compliant with the CD Audio specification and
therefore may not play.
A DualDisc is a new two -sided disc, one side
of which contains DVD content video, audio,
etc. while the other side contains non-DVD
content such as digital audio material.
Français
This player is compatible with a wide range of
disc types (media) and formats. Playable discs
will generally feature one of the following logos
on the disc and/or disc packaging. Note
however that some disc types, such as
recordable CD and DVD, may be in an
unplayable format — see below for further
compatibility information.
DVD-Audio
Deutsch
Disc/content format playback
compatibility
This unit supports the IEC’s Super VCD
standard. Compared to the Video CD standard,
Super VCD offers superior picture quality, and
allows two stereo soundtracks to be recorded.
Super VCD also supports the widescreen size.
English
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Surround
are registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-2007
DTS, Inc. All Rights Reserved.
14
• Multi-session playback: No
Fujicolor CD
• This unit will play DVD+R/+RW discs.
•
•
is a trademark of DVD Format/Logo
Licensing Corporation.
• Unfinalized disc playback: No
• File structure (may differ): Up to 299 folders
on a disc; up to 648 folders and files
(combined) within each folder
is a trademark of FUJIFILM Corporation.
• Also compatible with KODAK Picture CD.
73
En
LX03_En.book
14
74 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
DVD+R/DVD+RW compatibility
About MPEG-4 AAC
Only DVD+R/DVD+RW discs recorded in
‘Video Mode (DVD Video Mode)’ which have
been finalized, can be played back. However,
some editing made during the recording may
not be played back accurately.
Advanced Audio Coding (AAC) is at the core of
the MPEG-4 AAC standard, which incorporates
MPEG-2 AAC, forming the basis of the MPEG-4
audio compression technology. The file format
and extension used depend on the application
used to encode the AAC file. This unit plays
back AAC files encoded by iTunes bearing the
extension ‘.m4a’. DRM-protected files will not
play, and files encoded with some versions of
iTunes may not play, or filenames may display
incorrectly.
DVD-R/-RW compatibility
• Compatible formats: DVD-Video, Video
Recording (VR)*
* Edit points may not play exactly as edited;
screen may go momentarily blank at edited
points.
Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.
• Unfinalized playback: No
• MP3/WMA/MPEG-4 AAC/JPEG or DivX
video/WMV file playback on DVD-R/-RW:
Yes
Compressed audio compatibility
• Compatible formats: MPEG-1 Audio Layer 3
(MP3), Windows Media Audio (WMA),
MPEG-4 AAC
• Sampling rates: 32 kHz, 44.1 kHz or 48 kHz
• Bit-rates: Any (128 kbps or higher
recommended)
• VBR (variable bit rate) MP3/WMA/MPEG-4
AAC playback: No
• WMA lossless encoding compatible: No
• DRM (Digital Rights Management)
compatible: No (DRM-protected audio files
will not play in this unit.)
• File extensions: .mp3, .wma, .m4a (these
must be used for the player to recognize
MP3, WMA and MPEG-4 AAC files – do not
use for other file types)
74
En
WMA (Windows Media™ Audio)
compatibility
This player can playback Windows Media
Audio content.
WMA is an acronym for Windows Media Audio
and refers to an audio compression technology
developed by Microsoft Corporation. WMA
content can be encoded by using Windows
Media Player for Windows XP, Windows Media
Player 9 or Windows Media Player 10 series.
Windows Media is a trademark of Microsoft
Corporation.
This product includes technology owned by
Microsoft Corporation and cannot be used or
distributed without a license from Microsoft
Licensing, Inc.
LX03_En.book
75 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
• This player is compatible with WMV9 files
that are encoded by using the Windows
Media® Encoder 9 Series, with .wmv as an
extension.
• Compatible with size under 720 x 576
pixels/720 x 480 pixels.
• Advanced Profile is not supported.
• Compatible with bit rate under 192 kbps.
The font sets listed below are available for DivX
external subtitle files. You can see the proper
font set on-screen by setting the Subtitle
Language (in Language settings on page 54)
to match the subtitle file.2
Español
• DRM-protected video files will not play in
this player.
Nederlands
Displaying DivX subtitle files
WMV is an acronym for Windows Media Video
and refers to a video compression technology
developed by Microsoft Corporation. WMV
content can be encoded by using Windows
Media® Encoder.
Italiano
• Official DivX Certified product.
• Plays all versions of DivX video (including
DivX 6) with standard playback of DivX
media files.1
• File extensions: .avi and .divx (these must
be used for the player to recognize DivX
video files). Note that all files with the .avi
extension are recognized as MPEG4, but not
all of these are necessarily DivX video files
and therefore may not be playable on this
player.
About WMV
Français
DivX video compatibility
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license.
Deutsch
DivX is a compressed digital video format
created by the DivX video codec from DivX, Inc.
This player can play DivX video files burned on
CD-R/-RW and DVD-R/-RW/-ROM discs.
Keeping the same terminology as DVD-Video,
individual DivX video files are called ‘Titles’.
When naming files/titles on a CD-R/-RW or
DVD-R/-RW disc prior to burning, keep in mind
that by default they will play in alphabetical
order.
Rhaeto-Romanic (rm), Scottish (gd), Spanish (es),
Swedish (sv)
Group 2: Albanian (sq), Croatian (hr), Czech (cs),
Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk),
Slovenian (sl)
Group 3: Bulgarian (bg), Byelorussian (be),
Macedonian (mk), Russian (ru), Serbian (sr),
Ukrainian (uk)
Group 4: Hebrew (iw), Yiddish (ji)
Group 5: Turkish (tr)
English
About DivX
14
Group 1: Albanian (sq), Basque (eu), Catalan (ca),
Danish (da), Dutch (nl), English (en), Faroese (fo),
Finnish (fi), French (fr), German (de), Icelandic (is),
Irish (ga), Italian (it), Norwegian (no), Portuguese (pt),
Note
1 Playback of .avi video files larger than 4 GB is not possible.
2 • For external subtitle files the following subtitle format filename extensions are supported (please note that these files are not
shown within the disc navigation menu): .srt, .sub, .ssa, .smi
• Some external subtitle files may be displayed incorrectly or not at all.
• The filename of the movie file has to be repeated at the beginning of the filename for the external subtitle file.
• The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10.
75
En
LX03_En.book
14
76 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
JPEG file compatibility
• Compatible formats: Baseline JPEG and
EXIF 2.2* still image files up to a resolution
of 3072 x 2048.
*File format used by digital still cameras.
• Progressive JPEG compatible: No
• File extensions: .jpg (must be used for the
player to recognize JPEG files – do not use
for other file types)
PC-created disc compatibility
Discs recorded using a personal computer
may not be playable in this unit due to the
setting of the application software used to
create the disc. In these particular instances,
check with the software publisher for more
detailed information.
Discs recorded in packet write mode (UDF
format) are not compatible with this player.
Check the DVD-R/-RW or CD-R/-RW software
disc boxes for additional compatibility
information.
Using and taking care of discs
Handling discs
Hold the disc by its edges when handling so as
not to leave fingerprints, dirt or scratches on
either side of the disc. Damaged or dirty discs
can affect playback performance.
If a disc becomes marked with fingerprints,
dust, etc., clean using a soft, dry cloth.
If necessary, use a cloth soaked in alcohol, or a
commercially available CD/DVD cleaning kit to
clean a disc more thoroughly. Never use
benzine, thinner or other cleaning agents such
as those designed for cleaning vinyl records.
Storing discs
Avoid leaving discs in excessively cold, humid,
or hot environments (including under direct
sunlight). Don’t glue paper or put stickers onto
the disc, or use a pencil, ball-point pen or other
sharp-tipped writing instrument. These could
all damage the disc.
Discs to avoid
Discs spin at high speed inside the player. If a
disc is cracked, chipped, warped, or otherwise
damaged, don’t risk using it in your player—
you could end up damaging the unit.
This unit is designed for use with conventional,
fully circular discs only. Pioneer disclaims all
liability arising in connection with the use of
shaped discs.
DVD Video regions
All DVD Video discs carry a region mark that
indicates which region(s) of the world the disc
is compatible with. Your DVD system also has
a region mark (on the rear panel). Discs from
incompatible regions will not play in this
player. In this instance, the following message
appears on-screen:
Incompatible disc region number
Can’t play disc
Discs marked ALL play in any player.
Wipe lightly from the center of the disc using
straight strokes. Don’t wipe the disc surface
with circular strokes.
76
En
LX03_En.book
77 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
Hints on installation
Do...
 Use in a well-ventilated room.
 Place on a solid, flat, level surface, such as a
table, shelf or stereo rack.
Screen sizes and disc formats
DVD-Video discs come in different screen
aspects, ranging from TV programs, which are
generally 4:3, to CinemaScope widescreen
movies2, with an aspect ratio of up to about 7:3.
Televisions also come in different aspect
ratios; ‘standard’ 4:3 and widescreen 16:9.3
Widescreen TV users
Español
If you have a widescreen TV, the TV Screen
setting (page 53) of this player should be set to
16:9 (Wide) or 16:9 (Compressed).
When you watch discs recorded in 4:3 format
with the 16:9 (Wide) setting, you can use the
TV controls to select how the picture is
presented. Your TV may offer various zoom and
stretch options; see the instructions that came
with your TV for details.
Nederlands
The DVD player’s lens should not become dirty
in normal use, but if for some reason it should
malfunction due to dust or dirt, consult your
nearest Pioneer authorized service center.
Although lens cleaners are commercially
available, we do not recommend using them
since some may damage the lens.
If you need to move the main unit, first remove
a disc if there’s one in the player, then press
 STANDBY/ON on the front panel to turn the
system off. Wait for --Off-- to disappear from
the display, then unplug the power cord.1
Never lift or move the unit during playback —
discs rotate at high speeds and may damage.
Italiano
Cleaning the pickup lens
Moving the system unit
Français
Don’t...
 Use in a place exposed to high temperatures or
humidity, including near radiators and other
heat-generating appliances.
 Place on a window sill or other place where the
system will be exposed to direct sunlight.
 Use in an excessively dusty or damp
environment.
 Place directly on top of an amplifier, or other
component in your stereo system that becomes
hot in use.
 Use near a television or monitor as you may
experience interference — especially if the
television uses an indoor antenna.
 Use in a kitchen or other room where the system
may be exposed to smoke or steam.
 Use on a thick rug or carpet, or cover with cloth
— this may prevent proper cooling of the system
unit.
 Place on an unstable surface, or one that is not
large enough to support all four of the system
unit’s feet.
Condensation may form inside the player if it is
brought into a warm room from outside, or if
the temperature of the room rises quickly.
Although the condensation won’t damage the
player, it may temporarily impair performance.
Leave it to adjust to the warmer temperature
for about an hour before switching on.
Deutsch
We want you to enjoy using this system for
years to come, so please bear in mind the
following points when choosing a location:
Problems with condensation
English
Installation and maintenance
14
Note
1 Unplugging the unit before --Off-- disappears from the display may cause the system to return to the factory settings.
2 Many widescreen discs override the system’s settings so that the disc is shown in letterbox format regardless of the setting.
3 Using the 16:9 (Wide) or 16:9 (Compressed) setting with a standard 4:3 TV, or one of the 4:3 settings with a widescreen TV,
will result in picture distortion.
77
En
LX03_En.book
14
78 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
Please note that some movie aspect ratios are
wider than 16:9, so even though you have a
widescreen TV, these discs will still play in a
‘letter box’ style with black bars at the top and
bottom of the screen.
Standard TV users
If you have a standard TV, the TV Screen
setting (page 53) of this player should be set to
4:3 (Letter Box) or 4:3 (Pan & Scan),
depending on which you prefer.
Set to 4:3 (Letter Box), widescreen
discs are shown with black bars top
and bottom.
Set to 4:3 (Pan & Scan), widescreen
discs are shown with the left and
right sides cropped. Although the
picture looks larger, you don’t
actually see the whole picture.
Please note that many widescreen discs
override the player’s setting so that the disc is
shown in letter box format regardless of the
setting.
Using your own speaker cables
When connecting the speakers, you can
purchase and use your own speaker cables if
desired, in place of those furnished. In this
case, perform the following procedures to
attach the speaker cable adaptor to your own
cables:1
• While holding down the two buttons on
the adaptor, insert the wire ends of your own
cable into the adaptor.
Separately purchased
speaker cable
• White, Red, Blue, Gray and Purple speaker
cable adaptors are provided as
accessories. Use these to attach your own
cables for the front left/right speakers,
surround left/right speakers and
subwoofer.
• Use the supplied Y- cable for center
speakers connections.
• Confirm the +/– polarities of the two wires
and the corresponding markings on the
adaptor, and be sure to insert the proper
wire core into the proper side.
• After inserting the wire cores, pull gently
on the cable to confirm that the wires do
not slip out.
• Be careful to prevent the cores of the two
wires from touching each other, since a
short circuit will result.
Note
1 Speaker cables can be of sizes between 0.3 sq and 1.0 sq (equivalent to 22 gauge and 17 gauge, respectively).
78
En
LX03_En.book
79 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
• If the system does not operate normally due to external effects such as static electricity
disconnect the plug from the outlet and insert again to return to normal operating conditions.
• For audio-related problems, please also check the settings of the audio playback device. See
the operating instructions for the device for detailed information.
No sound is output
when an input function
is selected.
• If you’re using the line input, make sure the component is connected correctly
and the volume level of your external component (i.e. a portable player, etc.) is
adjusted (see Connecting auxiliary components on page 59).
• Turn up the volume.
• No audio is output from the speakers connected to this unit if HDMI Audio is set
to TV (page 63).
• No audio is output if a DVI component is connected via HDMI.
• Press MUTE on the remote control to turn muting off.
Español
• Leave the unit plugged in, wait for one minute, then switch back on.
• Make sure there are no loose strands of wire touching the unit. This could cause
the system to shut off automatically.
• Check that the speakers are connected correctly.
• Make sure there is enough space for ventilation around the unit.
• Make sure the voltage of the mains power source is correct for the model.
• Try reducing the volume level.
• If the problem persists, take it to your nearest Pioneer authorized service center
or your dealer for servicing.
• Do not block the air intake opening on the bottom as well as the air exhaust
opening on the back of this unit.
Nederlands
Remedy
The power does not turn
on, or switches off
suddenly (an error
message may be
displayed at startup). Or,
the display disappears
suddenly and no sound
is output.
Italiano
Problem
Français
General
Deutsch
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
English
Troubleshooting
14
No sound from surround • Refer to Channel level setting on page 49 to check the speaker levels.
or center speakers.
• Check that you haven’t selected the Auto, Stereo, A.L.C. or Virtual mode (see
Listening in surround sound on page 27).
• Connect the speakers properly (see Basic connections on page 12).
• Confirm audio output and HDMI settings for the external component
connected by optical digital cable, coaxial digital cable, or HDMI cable.
• If the source is 88.2 kHz/96 kHz, it will be played in stereo.
No sound from AUDIO
OUT jacks.
• Sound input from ANALOG RCA jacks cannot be output from AUDIO OUT
jacks.
79
En
LX03_En.book
14
80 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
Problem
Remedy
Can’t operate using the
remote control.
• Replace the batteries (see Putting the batteries in the remote control on page 21).
• Operate within 7 m, 30° of the remote sensor (see Using the remote control on
page 21).
• Remove any obstacles or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
• Check that there’s nothing mistakenly plugged into the CONTROL IN jack.
• For operating the other Pioneer component connected to the CONTROL OUT
jack of this unit, make sure that the control cable and either an HDMI or analog
audio cable are connected (page 62).
• If an object is placed on top of the touch sensor, the sensor will be activated,
thus disabling the remote control unit operations. If the action indicator remains
continuously lighted, remove any object sitting on the touch sensor panel.
The front panel display
and indicators do not
appear.
• If the display mode is set to Auto Display, the display will automatically turn off
if no operation is performed for a period of one minute. Try performing an
operation.
Motion sensor not
working.
• The motion sensor is on the front of the unit. Make sure you are within 2.5 m and
40° of the sensor.
• Since the motion sensor uses infrared rays, it may not work correctly if placed in
direct sunlight or close to heat source.
• Minimum unit height must be 25 cm or above from ground level. The sensor will
not work properly when located at ground level.
• Motion sensor will not work if placed in a fully sealed cabinet (include glass /
clear cabinet).
Tray Lock shows in the • Press and hold  OPEN/CLOSE on the front panel for about eight seconds. Then
display and the tray can’t the tray can be opened/closed using  OPEN/CLOSE.
be ejected.
DVD/CD/Video CD player
80
En
Problem
Remedy
The disc is ejected
automatically after
loading.
• Clean the disc and align the disc properly in the disc guide.
• If the region number on a DVD-video disc does not match the number on the
player, the disc cannot be used (see DVD Video regions on page 76). In this
instance, the following message appears on screen: Incompatible disc region
number/Can’t play disc.
• Allow time for any condensation inside the player to evaporate. Avoid using the
player near an air-conditioning unit.
Playback not possible.
• If the disc is loaded upside down, reload the disc with label side face up.
Picture playback stops
and buttons cannot be
used.
• Press  (stop), then  (play) to start playback again.
• Switch the power off once, then on again using the front panel  STANDBY/ON
button.
Settings are canceled.
• When the power is cut, settings will be canceled.
LX03_En.book
81 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
• Check that connections are correct and that plugs are inserted fully.
• Check the manual of the TV/monitor to make sure the settings are correct.
Screen is stretched or
aspect doesn’t change.
• The TV Screen setting is incorrect. Set the TV Screen option to match the TV/
monitor you’re using (page 53).
When recorded on a
VCR or passed through
an AV selector, there is
disturbance in the
playback picture.
• This system uses copy-protection technology which may prevent recording or
cause picture problems when connected through a VCR or AV selector. This is not
a malfunction.
DVD-ROM disc is not
recognized.
• Make sure that the DVD-ROM was recorded using the UDF bridge format. See
Disc/content format playback compatibility on page 73 for more on disc
compatibility.
Files don’t show up in
the Disc Navigator/
Photo Browser.
• The files on the disc must be named with the correct file extension: .mp3 for MP3
files; .wma for WMA files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or
lower-case is OK). See Disc/content format playback compatibility on page 73.
Can’t play WMA or
MPEG-4 AAC files.
• The files were recorded using DRM (digital rights management). This is not a
malfunction.
Can’t play WMV files.
• When the bit rate the file is more than 192 kbps, the file cannot be played back.
Español
• Make sure that the CD-ROM was recorded using the ISO 9660 disc format. See
Disc/content format playback compatibility on page 73 for more on disc
compatibility.
Nederlands
CD-ROM disc is not
recognized.
Italiano
Noticeable difference in • DVDs and CDs use different recording methods. This is not a malfunction.
DVD and CD volume.
Français
Picture disturbance
• This player is compatible with Macro-Vision System copy guard. Some discs
during playback or dark. include a copy prevention signal, and when this type of disc is played back, stripes
etc., may appear on some sections of the picture depending on the TV. This is not a
malfunction.
• Discs respond differently to particular player functions. This may result in the
screen becoming black for a brief instant or shaking slightly when the function is
executed. These problems are largely due to differences between discs and disc
content and are not malfunctions of this player.
Deutsch
Remedy
No picture/No color.
English
Problem
14
Tuner
Problem
Remedy
Considerable noise in
radio broadcasts.
• Connect the AM antenna (see Basic connections on page 12) and adjust the
direction and position for best reception. You may also connect an additional
internal or external AM antenna (refer to Connecting external antennas on
page 61).
• Fully extend the FM wire antenna, position for best reception, and secure to a
wall. You may also connect an outdoor FM antenna (see Connecting external
antennas on page 61).
• Turn off other equipment that may be causing the noise or move it further away.
81
En
LX03_En.book
14
82 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
Problem
Remedy
Auto tuning does not
pick up some stations.
• The radio signal is weak. Auto tuning will only detect radio stations with a good
signal. For more sensitive tuning, connect an outdoor antenna.
USB connection
Problem
Remedy
USB mass storage
• Make sure you have completely inserted the USB connector to this unit.
device is not recognized • Check that the memory format is FAT16 or FAT32.
by the system.
• USB devices with an internal USB hub are not supported.
Files don’t show up in
the Navigator/Photo
Browser.
• The files must have the correct file extension: .mp3 for MP3 files; .wma for WMA
files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or lower-case is OK).
• Make sure the file permission hasn’t been restricted (through a password, etc.).
Can’t play WMA or
MPEG-4 AAC files.
• The files were recorded using DRM (digital rights management). This is not a
malfunction.
HDMI connection
82
En
Symptom
Remedy
No picture or sound.
• This unit is HDCP-compatible. Check that the components you are connecting
are also HDCP-compatible.
• Depending on the connected source component, it’s possible that it will not
work with this unit (even if it is HDCP-compatible).
• If the problem still persists when connecting your HDMI component directly to
your monitor, please consult the component or monitor manual or contact the
manufacturer for support.
No sound, or sound
suddenly ceases.
• Check that the HDMI Audio is set to AMP.
• If the component is a DVI device, use a separate connection for the audio.
• Check the audio output settings of the source component.
HDMI Control does not
function.
• Verify that the HDMI cable is firmly connected.
• Make sure that this unit’s HDMI Control mode is set to Control On (page 67).
• Check whether the connected component supports HDMI Control or not. For
more information refer to the operating manual of your flat screen TV, DVD player,
Blu-ray disc player, etc.
• This unit does not guarantee HDMI Control-compatible components other than
those made by Pioneer.
• HDMI Control may not work properly if a SCART cable and an HDMI cable are
connected simultaneously. Set HDMI Control mode to Control Off when
connecting SCART and HDMI cables simultaneously.
Your TV automatically
change inputs.
• The connected TV automatically may change inputs in response to this unit
starting playback DVD or having the GUI screen (ex. Disc Navigator) displayed, etc.
If you do not want your TV to change inputs in this way, set this unit HDMI Control
mode to Control Off (page 67).
LX03_En.book
83 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
96kHz PCM
An operation is prohibited because the source is 88.2 kHz/96 kHz PCM.
Error MIC!
An error occurred during MCACC setup because the microphone is not connected
or is not connected properly.
Error Speaker!
An error occurred during MCACC setup because the speakers are not connected or
are not connected properly.
Exit
Appears when a menu is automatically exited after a set period of inactivity.
HDMI Audio <TV>
Displays when you change the listening mode, the volume level, or some sound
settings when the HDMI Audio is set to TV.
HDMI C.ERR 1**
Check if the HDMI cable is properly connected. If the cable is properly connected,
this unit may be damaged. In such an event, please contact a Pioneer-authorized
service center or your nearest dealer.
HDCP ERROR
Check whether or not the connected component is compatible with HDCP. If it is not
compatible with HDCP, reconnect the source device using a different type of
connection (SCART or composite). Some components that are compatible with
HDCP still cause this message to be displayed, but so long as there is no problem
with displaying video, this is not a malfunction.
Key Lock
The key lock is enabled. See Key lock setting on page 70.
Line Out Mode
Operation is disabled since Line Output is set to Lt/Rt.
Muting
When audio is muted, display appears if Auto MCACC setup is performed.
No MIC
Display appears when Auto MCACC setup is performed without a microphone
connected.
Noisy!
Background noise is too high to complete MCACC setup successfully.
Not support
For HDMI1 or 2 inputs:
Try adjusting the resolution, DeepColor or other setting for your component.
For DVD input:
Try changing the resolution in the HDMI Resolution setting (page 54).
OC Error1
OC Error2
Check whether the speaker cables are short-circuited. If the error message continues
to be displayed, contact your Pioneer authorized service center or your dealer for
servicing.
Over Temp
Try lowering the volume. If this problem is not fixed by removing and inserting the
power cable, this unit may be damaged. In such an event, please contact a Pioneerauthorized service center or your nearest dealer.
Phones In
An operation is prohibited because the headphones are connected.
Tray Lock
The tray lock is on (see page 80).
USB Error
See Important on page 43 for more on this.
*** BackUpERR
Contact your Pioneer authorized service center or your dealer for servicing.
Español
An operation is prohibited because it is only applicable to 2 channel sources, while
the current source is a multichannel source.
Nederlands
2ch Only
Italiano
An operation is prohibited because the source is 176.4 kHz/192 kHz PCM.
Français
Description
Deutsch
Message
192kHz PCM
English
Front panel display messages
14
83
En
LX03_En.book
14
84 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
Resetting the system
Use this procedure to reset all system settings
to the factory default.
SETUP
1
Press SETUP.
Display Mode
Display Mode
Line Output
Line Output
TV Input
TV Input
HDMI Audio
HDMI Audio
HDMI Control mode
HDMI Ctrl
Auto Delay
Auto Delay
Storing stations
-
ENTER
2
ENTER.
Select ‘Initialize’ then press
Using the language code list
ENTER
3
Select ‘All Init’ then press ENTER.
• Initialize OK? is displayed.
4 ENTER Press ENTER to confirm initialization.
The system will restart and all the system
settings should be reset.
• Note that following settings will be saved,
even if the receiver is unplugged.
84
En
Input function
‘HDMI 1’, ‘Digital 1’, etc.
Listening mode
‘Auto’, ‘Action’, etc.
Sound Retriever
‘Retriever On’ or
‘Retriever Off’
Sound Field
Sound Field
Tone controls
Bass, Treble, Quiet,
Midnight
Bass Mode
Bass Mode
Dialogue Enhancement
Dialogue
Acoustic Calibration EQ
MCACC EQ
Sound Delay
Sound Delay
Center Width
Center Width
Dimension
Dimension
Panorama
Panorama
Channel Level
Channel Level
Speaker Distance
Distance
Dynamic Range Control
D.R.C.
Dual Mono
Dual Mono
Virtual Surround Back
Virtual SB
LFE Attenuator
LFE ATT
CD Type
CD Type
Some of the language options (see Language
settings on page 54) allow you to set your
preferred language from any of the 136
languages in the Language code list below.
1
Select ‘Other Language’.
2
Select either a code letter or a
code number.
3
Select a code letter or a code
number.
See the Language code list below for a
complete list of languages and codes.
LX03_En.book
85 ページ
2008年6月24日
火曜日
午後6時1分
Additional information
14
Language (Language code letter), Language code
Nederlands
Español
Slovak (sk), 1911
Slovenian (sl), 1912
Samoan (sm), 1913
Shona (sn), 1914
Somali (so), 1915
Albanian (sq), 1917
Serbian (sr), 1918
Siswati (ss), 1919
Sesotho (st), 1920
Sundanese (su), 1921
Swedish (sv), 1922
Swahili (sw), 1923
Tamil (ta), 2001
Telugu (te), 2005
Tajik (tg), 2007
Thai (th), 2008
Tigrinya (ti), 2009
Turkmen (tk), 2011
Tagalog (tl), 2012
Setswana (tn), 2014
Tonga (to), 2015
Turkish (tr), 2018
Tsonga (ts), 2019
Tatar (tt), 2020
Twi (tw), 2023
Ukrainian (uk), 2111
Urdu (ur), 2118
Uzbek (uz), 2126
Vietnamese (vi), 2209
Volapük (vo), 2215
Wolof (wo), 2315
Xhosa (xh), 2408
Yoruba (yo), 2515
Zulu (zu), 2621
Italiano
Lingala (ln), 1214
Laothian (lo), 1215
Lithuanian (lt), 1220
Latvian (lv), 1222
Malagasy (mg), 1307
Maori (mi), 1309
Macedonian (mk), 1311
Malayalam (ml), 1312
Mongolian (mn), 1314
Moldavian (mo), 1315
Marathi (mr), 1318
Malay (ms), 1319
Maltese (mt), 1320
Burmese (my), 1325
Nauru (na), 1401
Nepali (ne), 1405
Norwegian (no), 1415
Occitan (oc), 1503
Oromo (om), 1513
Oriya (or), 1518
Panjabi (pa), 1601
Polish (pl), 1612
Pashto, Pushto (ps), 1619
Portuguese (pt), 1620
Quechua (qu), 1721
Rhaeto-Romance (rm), 1813
Kirundi (rn), 1814
Romanian (ro), 1815
Kinyarwanda (rw), 1823
Sanskrit (sa), 1901
Sindhi (sd), 1904
Sangho (sg), 1907
Serbo-Croatian (sh), 1908
Sinhalese (si), 1909
Français
Esperanto (eo), 0515
Estonian (et), 0520
Basque (eu), 0521
Persian (fa), 0601
Finnish (fi), 0609
Fiji (fj), 0610
Faroese (fo), 0615
Frisian (fy), 0625
Irish (ga), 0701
Scots-Gaelic (gd), 0704
Galician (gl), 0712
Guarani (gn), 0714
Gujarati (gu), 0721
Hausa (ha), 0801
Hindi (hi), 0809
Croatian (hr), 0818
Hungarian (hu), 0821
Armenian (hy), 0825
Interlingua (ia), 0901
Interlingue (ie), 0905
Inupiak (ik), 0911
Indonesian (in), 0914
Icelandic (is), 0919
Hebrew (iw), 0923
Yiddish (ji), 1009
Javanese (jw), 1023
Georgian (ka), 1101
Kazakh (kk), 1111
Greenlandic (kl), 1112
Cambodian (km), 1113
Kannada (kn), 1114
Kashmiri (ks), 1119
Kurdish (ku), 1121
Kirghiz (ky), 1125
Latin (la), 1201
Deutsch
Japanese (ja), 1001
English (en), 0514
French (fr), 0618
German (de), 0405
Italian (it), 0920
Spanish (es), 0519
Dutch (nl), 1412
Russian (ru), 1821
Chinese (zh), 2608
Korean (ko), 1115
Greek (el), 0512
Afar (aa), 0101
Abkhazian (ab), 0102
Afrikaans (af), 0106
Amharic (am), 0113
Arabic (ar), 0118
Assamese (as), 0119
Aymara (ay), 0125
Azerbaijani (az), 0126
Bashkir (ba), 0201
Byelorussian (be), 0205
Bulgarian (bg), 0207
Bihari (bh), 0208
Bislama (bi), 0209
Bengali (bn), 0214
Tibetan (bo), 0215
Breton (br), 0218
Catalan (ca), 0301
Corsican (co), 0315
Czech (cs), 0319
Welsh (cy), 0325
Danish (da), 0401
Bhutani (dz), 0426
English
Language code list
Country/Area code list
Country/Area, Country/Area code, Country/Area code letter
Argentina, 0118, ar
Australia, 0121, au
Austria, 0120, at
Belgium, 0205, be
Brazil, 0218, br
Canada, 0301, ca
Chile, 0312, cl
China, 0314, cn
Denmark, 0411, dk
Finland, 0609, fi
France, 0618, fr
Germany, 0405, de
Hong Kong, 0811, hk
India, 0914, in
Indonesia, 0904, id
Italy, 0920, it
Japan, 1016, jp
Korea, Republic of, 1118, kr
Malaysia, 1325, my
Mexico, 1324, mx
Netherlands, 1412, nl
New Zealand, 1426, nz
Norway, 1415, no
Pakistan, 1611, pk
Philippines, 1608, ph
Portugal, 1620, pt
Russian Federation, 1821, ru
Singapore, 1907, sg
Spain, 0519, es
Switzerland, 0308, ch
Sweden, 1905, se
Taiwan, 2023, tw
Thailand, 2008, th
United Kingdom, 0702, gb
United States of America, 2119, us
85
En
14_Additional_info.fm 86 ページ
14
2008年7月1日
DVD/CD receiver
•
Amplifier section
RMS Power Output:
Front, Center . . . . . . . . . . . 100 W per channel
(1 kHz, 10 % T.H.D., 4 Ω)
Surround. . . . . . . . . . . . . . . . 50 W per channel
(1 kHz, 10 % T.H.D., 8 Ω)
Subwoofer. . . 100 W (100 Hz, 10 % T.H.D., 4 Ω)
•
Disc section
Type . . . . . . . DVD system, Video CD/Super VCD
system and Compact Disc digital audio system
Wow and Flutter . . . . . . . .Limit of measurement
(±0.001 % W.PEAK) or less (JEITA)
•
FM tuner section
Frequency range . . . . . . . . 87.5 MHz to 108 MHz
Antenna . . . . . . . . . . . . . . . . . . 75 Ω, unbalanced
•
AM tuner section
Frequency range . . . . . . . . . 531 kHz to 1602 kHz
Antenna . . . . . . . . . . . . . . . . . . . . . .Loop antenna
•
Input/Output section
HDMI terminal:
Input. . . . . . . . . . . . . . . . . . . . . . . . . . . 19-pin x2
Output . . . . . . . . . . . . . . . . 19-pin (5 V, 55 mA)
Audio input . . . . . Coaxial x1, Optical x2 (Digital)
RCA (2-pin) (Analog)
Audio output . . . . . . . . . . . . RCA (2-pin) (Analog)
Video output . . . . . . . . . . . . . . . . . . . . . . . RCA x1
AV connector output. . . . . . . . . . . . . . . . . . 21-pin
Control jack . . . . Input x1, Output x1 (Mini jack)
MCACC input . . . . . . . . . . . . . . . . . . . . .Mini jack
iPod/USB connector . . . . . . . . . . . . . .5 V, 500 mA
En
午後1時30分
Additional information
Specifications
86
火曜日
•
Miscellaneous
Power requirements
. . . . . . . . . . . . . . . AC 220 V to 240 V, 50 Hz/60 Hz
Power consumption . . . . . . . . . . . . . . . . . . .60 W
Power consumption in standby
. . . . . . . . . . . . . . . . . . . 0.7 W (HDMI Control ON)
0.4 W (HDMI Control OFF)
Dimensions
. . . . . . . .420 mm (W) x 80 mm (H) x 364 mm (D)
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 kg
Speaker system
(Front speakers x2, Center speakers x2, Surround
speakers x2, Subwoofer x1)
•
Front speakers
Enclosure . . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System . . . . . . . . . . . . . . . . . . . . . . .2-way system
Speakers:
Woofer . . . . . . . . . . . . . . . 5.2 cm cone type x2
Tweeter . . . . . . . . . . . . 2.6 cm semi-dome type
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω
Frequency range . . . . . . . . . . . . 200 Hz to 20 kHz
Maximum input power . . . . . . . . . . . . . . . .100 W
Dimensions
. . . . . . . 80 mm (W) x 196.8 mm (H) x 82 mm (D)
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.02 kg
•
Center speakers
Enclosure . . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System . . . . . . . . . . . . . . . . 5.2 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . 5.2 cm cone type
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω
Frequency range . . . . . . . . . . . . 200 Hz to 20 kHz
Maximum input power . . . . . . . . . . . . . . . . .50 W
Dimensions
. . . . . . . . . .80 mm (W) x 80 mm (H) x 82 mm (D)
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.48 kg
14_Additional_info.fm 87 ページ
2008年7月1日
火曜日
午後1時30分
Additional information
•
Surround speakers
DVD/CD receiver box:
Español
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/R6 dry cell batteries
(to confirm system operation) . . . . . . . . . . . . . . 2
Video cable (yellow plugs) . . . . . . . . . . . . . . . . . 1
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Microphone (for Auto MCACC setup) . . . . . . . . 1
Power cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Speaker cable adaptors
(White, Red, Blue, Gray, Purple) . . . . . . . 1 each
Cleaning cloth . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Setup Guide
These operating instructions
This product incorporates copyright
protection technology that is protected
by method claims of certain U.S. patents
and other intellectual property rights
owned by Macrovision Corporation and
other rights owners. Use of this copyright
protection technology must be authorized
by Macrovision Corporation, and is intended
for home and other limited viewing uses
only unless otherwise authorized by
Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Nederlands
•
This product includes FontAvenue®
fonts licenced by NEC corporation.
FontAvenue is a registered trademark
of NEC Corporation.
Italiano
Accessories
Note
• Specifications and design subject to
possible modification without notice, due
to improvements.
Français
Subwoofer
Enclosure . . . . . . . Bass-reflex floorstanding type
System . . . . . . . . . . . . . . . . . 18 cm 1-way system
Speaker. . . . . . . . . . . . . . . . . . . . 18 cm cone type
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω
Frequency range . . . . . . . . . . . . 25 Hz to 1500 Hz
Maximum input power . . . . . . . . . . . . . . . .100 W
Dimensions
. . . . . . . 211 mm (W) x 320 mm (H) x 358 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.50 kg
Speakers box:
Speaker cables . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Screws (for brackets) . . . . . . . . . . . . . . . . . . . . . 4
Speaker stands . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Non-skid pads (for satellite speakers). . . . . . . .24
Non-skid pads (for subwoofer) . . . . . . . . . . . . . 4
Non-skid pads (for speaker stands) . . . . . . . . . 8
Spiral wrap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Deutsch
•
•
English
Enclosure . . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System . . . . . . . . . . . . . . . . . . . . . . .2-way system
Speakers:
Woofer . . . . . . . . . . . . . . . . . .5.2 cm cone type
Tweeter . . . . . . . . . . . . 2.6 cm semi-dome type
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω
Frequency range . . . . . . . . . . . . 200 Hz to 20 kHz
Maximum input power . . . . . . . . . . . . . . . . .50 W
Dimensions
. . . . . . . 80 mm (W) x 115.8 mm (H) x 82 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.60 kg
14
DRM (digital rights management)
copy protection is a technology
designed to prevent unauthorized
copying by restricting playback, etc. of
compressed audio files on devices
other than the PC (or other recording
equipment) used to record it. For
detailed information, please see the
instruction manuals or help files that
came with your PC and/or software.
87
En
99_backcover.fm
88 ページ
2008年7月1日
火曜日
午後1時31分
Discover the benefits of registering your product online at
http://www.pioneer.co.uk (or http://www.pioneer.eu)
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270
K002_B_En
Published by Pioneer Corporation.
Copyright © 2008 Pioneer Corporation.
All rights reserved.
<XRB3101-B>
Printed in

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement