CipherLab 8500 Series, 8570 Reference Manual
Advertisement
Advertisement
8500 Series Mobile Computer
8500/8570
Version 2.21
Copyright © 2006~2011 CIPHERLAB CO., LTD.
All rights reserved
The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited.
Due to continued product development this information may change without notice. The information and intellectual property contained herein is confidential between CIPHERLAB and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find any problems in the documentation, please report them to us in writing. CIPHERLAB does not warrant that this document is error-free.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of CIPHERLAB CO., LTD.
For product consultancy and technical support, please contact your local sales representative. Also, you may visit our web site for more information.
The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD.
All brand, product and service, and trademark names are the property of their registered owners.
The editorial use of these names is for identification as well as to the benefit of the owners, with no intention of infringement.
CIPHERLAB CO., LTD.
Website: http://www.cipherlab.com
IMPORTANT NOTICES
FOR USA
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FOR CANADA
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled
"Digital Apparatus," ICES-003 of Industry Canada.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Classe B prescrites dans la norme sur le material brouilleur:
"Appareils Numeriques," NMB-003 edictee par l'Industrie.
FOR HAND-HELD PRODUCT WITH RF FUNCTIONS
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. It only operated in hand-held used.
If you only transfer data to the host wirelessly, please keep the minimum distance 20 cm between machine & your body.
FOR PRODUCT WITH LASER
CAUTION
This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not stare into beam.
SAFETY PRECAUTIONS
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
The use of any batteries or charging devices, which are not originally sold or manufactured by CipherLab, will void your warranty and may cause damage to human body or the product itself.
DO NOT disassemble, incinerate or short circuit the battery.
DO NOT expose the scanner or the battery to any flammable sources.
For green-environment issue, it's important that batteries should be recycled in a proper way.
Under no circumstances, internal components are self-serviceable.
The charging and communication cradle uses an AC power adaptor. A socket outlet shall be installed near the equipment and shall be easily accessible. Make sure there is stable power supply for the mobile computer or its peripherals to operate properly.
CARE & MAINTENANCE
This mobile computer is intended for industrial logistics use. The mobile computer is rated IP 64, however, it may do damage to the mobile computer when being exposed to extreme temperatures or soaked wet.
When the body of the mobile computer gets dirty, use a clean and wet cloth to wipe off the dust. DO NOT use/mix any bleach or cleaner. Always keep the LCD dry.
For a liquid crystal display (LCD) or touch screen, use a clean, non-abrasive, lint-free cloth to wipe dust off the screen. DO NOT use any pointed or sharp object to move against the surface.
If you want to put away the mobile computer for a period of time, download the collected data to a host computer, and then take out the battery pack. Store the mobile computer and battery pack separately.
When the mobile computer resumes its work, the main and backup batteries will take a certain time to become fully charged.
If you shall find the mobile computer malfunctioning, write down the specific scenario and consult your local sales representative.
RELEASE NOTES
Version Date
2.21 Mar. 09, 2011
2.20
2.12
2.11
2.10
2.01
2.00
1.07
1.06
1.05
1.04
Oct. 28, 2010
May 20, 2009
July 21, 2008
Notes
Modified: 3.7 Bluetooth Menu — Not maintain Bluetooth PAN
(=BNEP) from 2011
Modified: Specifications — add power adaptor spec.
New: Appendix III Key Reference Tables
Modified: Remove support of 8580/8590
Modified: 1.6.1 Symbologies Supported — ISBT 128 enabled by default and UPC/EAN Addon 2 & 5 disabled by default; add more
GS1 DataBar symbologies
Modified: 3.7 Bluetooth Menu — update table (add HID)
Modified: 3.7.4 Echo Tests — Add “HID Test”
Modified: 3.7.5 Pairing Test — Max. 11 characters for device name
Modified: 3.7.6 Freq. Dev. List — Max. 11 characters for device name
Modified: 3.10.3 WLAN Setting — Add “Fixed BSSID”
Modified: Specifications — 70 hours working time in Wi-Fi mode
Modified: 1.3.2 24-key Layout — Press the Alpha key once to input capital letters
Modified: 4.1.1 Download — [C], [D] are case-sensitive
Modified: 1.3.3 44-key Keypad – “59-key” corrected to “44-key”
Apr. 24, 2008 New Word template applied
Aug. 10, 2007
May 19, 2007
Oct. 31, 2006
July 27, 2006
June 22, 2006
June 16, 2006
Modified: 1.5.9 Reader – Defaults updated
Modified: 4.1.8.(4) GSM/GPRS Menu> Security
Modified: 4.1.8.(4) GSM/GPRS Menu> GPRS Settings
New release
Modified: 1.5.9 List by standards for RFID tags
Modified: 1.5.10 Bluetooth specification
Modified: 4.1.7 Bluetooth Menu > Security – max. 16 characters for PIN
Modified: 1.3.9 Reader – RFID (add ICODE)
Modified: 2.5.2 Front Panel (LEDs of cradle)
New: 4.1.8(2) System Menu > IR Network Menu
Modified: 1.3.9 Reader – RFID
Modified: 4.1.1 Information – add RFID version
FCC Regulations – Class B statement
Modified: 1.3.9 Reader – Symbologies Supported & Enabled
1.03
1.02
1.00
May 23, 2006 Company name changed to CIPHERLAB CO., LTD. since April 2006
Apr. 04, 2006
New: Safety Precaution
Modified: Care & Maintenance
Modified: 1.2.3 Dimensions & Specifications
Modified: 1.3.4 Keypad – Screen Icons
Modified: 1.3.5 LCD – Screen & Backlight Settings
Modified: 1.3.12 Application Software to include AG and CipherNet
Modified: 2, 2.5 ~ 2.7
Modified: 3.1 & 3.3
Modified: 4.1.2 Screen Calibration
Modified: 4.1.6 Load Program via Bluetooth
Update drawings
Load Program via Bluetooth
Mar. 01, 2006 Initial release
CONTENTS
8500 Series Mobile Computer Reference Manual
8500 Series Mobile Computer Reference Manual
8500 Series Mobile Computer Reference Manual
INTRODUCTION
Answering heavy industrial demands for robust, versatile and high performance computers, the 8500 Series Mobile Computer is specifically designed for all-day, everyday use as well as for data-intensive applications in harsh environments.
This line of product comes with built-in Bluetooth technology and allows for optional modules for 802.11b/g, enabling all the time, anywhere applications and seamless real time sharing of performance.
The 8500 Series Mobile Computer is bundled with powerful and rich features to ensure success in timely processing of information, even in rigorous industrial environments, and thus, makes an ideal choice for a wireless solution in either increasing business flexibility or answering the demanding needs of heavy-duty mobile computers. Being programmable, this handy device can run custom applications or terminal emulation applications.
This manual serves to guide you through how to install, configure, and operate the mobile computer. We recommend you to keep one copy of the manual at hand for quick reference or maintenance purposes. To avoid any improper disposal or operation, please read the manual thoroughly before use.
Thank you for choosing CipherLab products!
1
8500 Series Mobile Computer Reference Manual
GETTING FAMILIARIZED WITH 8500
Figure 1: Overview
No. Description
1
3
LCD touch screen
Keypad, 24 or 44 keys
5 Stylus
7 Hand strap (to be screwed)
No. Description
2
4
LED for Good Read and battery charging
Communication/charging port
8 Pistol Grip, optional (to be screwed after removal of this cover)
10 Li-ion Battery, fit to compartment 9 Battery Latch
Warning: Always make sure the hand strap is well hooked and screwed to the back of the mobile computer before use.
2
FEATURES
Introduction
Ergonomic design — ruggedized yet streamlined, with hand strap for secure hold
Built tough to survive drop test and sealed against moisture/dust to IP 64
Upgradeable memory — adds up to 10 MB (2 MB onboard + 8 MB) for data storage
Dual mode support — one barcode scan engine plus the RFID reader
Flexible wireless solutions — IR/IrDA and Bluetooth integrated, with connectivity options for 802.11b/g
Large graphic monochrome LCD touch screen supports double-byte characters and bitmap graphics. The touch screen featuring signature capture can be activated with its stylus or a finger, software programmable
Programmable feedback includes buzzer, LED indicator, and vibrator
Quick link to any backend database through MIRROR Emulator programs for
VT100/220 and IBM 5250 emulation
Easy customization of data collection applications through FORGE Application
Generator (AG) programs for preloaded AG Runtime, batch and WLAN versions available
Programming support includes BASIC & C compilers
Accessories include pistol grip, 4-Slot Battery Charger and a variety of charging/communications cradle, etc.
INSIDE THE PACKAGE
The following items are included in the package. Save the box and packaging material for future use in case you need to store or ship the mobile computer.
8500 Series mobile computer
Rechargeable Li-ion battery pack
Stylus
Hand strap
Product CD
Note: For battery charging, you need to purchase a charging cradle separately.
3
4
8500 Series Mobile Computer Reference Manual
ACCESSORIES
Rich choices of optional accessories are available for you to enhance the total performance of the mobile computer.
Pistol Grip (detachable)
Belt Holster
Protective Cover
Spare rechargeable Li-ion battery
4-slot Battery Charger
Charging & Communication Cradle
Modem Cradle
Ethernet Cradle (10/100 BASE-T)
Vehicle Cradle
Travel Charger
GETTING STARTED
Introduction
INSTALLING HAND STRAP
The hand strap is ideal for one-handed operation, which requires safe and convenient hold of the mobile computer.
Warning: Always make sure the hand strap is well hooked and screwed to the back of the mobile computer before use.
When the hand strap is desired, install it to the mobile computer by following these steps:
1) Place the mobile computer face down on a flat and clean surface.
2) Screw one end of the hand strap to the back of the mobile computer.
3) Insert and hook the other end of the hand strap to the bottom of the mobile computer.
4) Make sure the hand strap is securely attached to the mobile computer.
Figure 2: Installing the Hand Strap
5
8500 Series Mobile Computer Reference Manual
INSTALLING PISTOL GRIP
This contoured pistol grip enables intuitive trigger-and-scan operation, which is very helpful in scan intensive applications. When the pistol grip is desired, install it to the mobile computer by following these steps:
1) Place the mobile computer face down on a flat and clean surface.
2) Remove the shield-like cover on the back of the mobile computer by unscrewing.
If the hand strap is installed, remove it first. Keep the cover and screws for future use when the pistol grip is not desired.
3) Connect the power connector from the pistol grip to the receptacle on the mobile computer.
4) Screw the pistol grip to the shield-like cover.
5) Make sure all screws are tightened up.
6) Turn on the mobile computer and test the trigger.
Figure 3: Installing the Pistol Grip
6
INSERTING BATTERY
Introduction
For shipping and storage purposes, save the mobile computer and the main battery in separate packages. This will keep both batteries in good condition for future use.
Note: Any improper handling may reduce the battery life.
1) Hold the mobile computer still as shown below.
2) Slide the battery pack into the battery compartment at a proper angle (30°~45°) so that the metal contacts of the battery are met with the charging contacts inside the compartment. Make sure that the battery is snugly fit into the compartment.
3) Slide the battery latch to lock the battery in the compartment.
Note: For a new battery, make sure it is fully charged before use. Always prepare a spare battery pack, especially when you are on the road.
Figure 4: Installing the Main Battery
7
8
8500 Series Mobile Computer Reference Manual
INITIAL CHARGING
The main and backup batteries may not be charged to full for shipment. When you first receive the package, you will need to charge batteries to full before using the mobile computer. You may use a cradle or charger to charge the Mobile Computer or spare
batteries. Refer to 1.7 Charging & Communications
.
Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It is recommended to charge the battery at room temperature (18°C to 25°C) for optimal performance. For initial charging, it takes approximately 4 hours to charge the battery to full.
Because the internal backup battery is constantly charged from the main battery, the initial charging requires inserting the battery pack to the mobile computer and then seating the mobile computer in the cradle for charging. This will have both the main and backup batteries charged at the same time. It takes at least 24 hours to fully charge the backup battery. However, it is not necessary to fully charge the backup battery for the mobile computer to work.
Note: In order to charge the backup battery to full, you must insert the main battery and leave it for at least 24 hours, whether the mobile computer is in use or not.
SETTING LOCAL TIME
If you need to set your local time, go to System Menu | 2. Settings | 1. Clock . Refer to
POWER MANAGEMENT
For any portable device, power management is a critical issue especially when you are on the road. Below are some tips to help you save battery power.
Warning: Using backlight, wireless connectivity, and peripherals while on battery power will substantially reduce battery power.
To speed up charging the mobile computer, turn off the mobile computer and seat it in the cradle.
Bring a second battery pack on the road.
Stop wireless connectivity, Bluetooth or 802.11b/g that is not in use.
Go to System Menu | 2. Settings | 2. Backlight Period , and configure backlight
period and luminosity. Refer to 3.2.2 Backlight Period .
Go to System Menu | 2. Settings | 3. Auto Off , and configure the amount of idle
time that must pass before the system will shut down automatically. Refer to 3.2.3
Chapter 1
USING 8500 MOBILE COMPUTER
This chapter explains the features and usage of the 8500 Series Mobile Computer. The
8500 family includes:
8500
8570
Bluetooth Class 2
Bluetooth Class 2 + 802.11b/g
IN THIS CHAPTER
1.1 Battery....................................................................... 9
1.2 Memory.................................................................... 11
1.3 Keypad..................................................................... 12
1.4 LCD ......................................................................... 23
1.5 Notifications.............................................................. 25
1.6 Data Capture ............................................................ 26
1.7 Charging & Communications........................................ 29
1.1 BATTERY
1.1.1 MAIN BATTERY
The mobile computer is powered by a rechargeable 3.7 V/4000 mAh Li-ion battery pack, and it takes approx. four hours to charge it to full.
For power-saving purpose, always turn off the backlight while working in a well-lit area.
When the backlight is on for extended periods of time, the main battery will become low sooner than expected.
The smart battery icon on the LCD screen shows the status of power consumption. There are two ways to monitor a low battery charge or discharged battery from the screen.
Examine the level of the 4-bar battery icon
Monitor voltage level (see 3.5 Power )
9
8500 Series Mobile Computer Reference Manual
1.1.2 BACKUP BATTERY
The backup battery on the main board takes charge when the main battery is removed or drained out. When fully charged, the 3.0 V/7 mAh rechargeable Lithium button cell helps retain data in SRAM and maintain the running of the real-time clock and calendar for at least one week without the main battery. In the meantime, you have to replace the main battery as soon as possible. It takes at least twenty-four hours to fully charge the backup battery. However, it is not necessary to fully charge the backup battery for the mobile computer to work.
Monitor voltage level (see 3.5 Power )
1.1.3 CAUTION OF LOW BATTERY CHARGE
The battery pack is the only power source for the mobile computer to work. It also charges the backup battery on the main board so that the data stored in SRAM can be retained properly. Therefore, when the main battery charge goes low, you need to replace the battery pack with a charged one or charge it as soon as possible. Most of all, you should upload important data on a regular basis.
Warning: Data loss may occur with SRAM during low battery condition. Always save data before running out of power or keep a fresh battery for replacement.
10
1.2 MEMORY
Chapter 1 Using 8500 Mobile Computer
The collected data can be sent back to a host computer immediately over wireless networks, or stored in memory (SRAM) and upload later. The mobile computer is equipped with a calendar chip for accurate time/date logging. When the main battery is removed or drained, the backup battery on the main board is to retain the contents of
SRAM and maintain the running of real-time clock and calendar for at least one week, on condition that the backup battery has already been fully charged.
If you want to put away the mobile computer for a couple of days, you should be aware that data loss occurs when both the main and backup batteries discharge completely.
Therefore, it is necessary to upload data and files before putting away the mobile computer!
1.2.1 READ-ONLY MEMORY (ROM)
2 megabytes flash memory for storing core, OS, application programs, fonts, etc.
1.2.2 RANDOM-ACCESS MEMORY (RAM)
2 megabytes SRAM for storing data. Its contents will be retained by the backup battery.
1.2.3 UPGRADEABLE MEMORY
When ordering, you may choose to have up to 10 MB memory — 2 MB onboard + 8 MB for data storage.
4 or 8 MB optional
11
8500 Series Mobile Computer Reference Manual
1.3 KEYPAD
The mobile computer can be equipped with a keypad of 24 keys or 44 keys for system setup, user entry and so on. The keypad comes with programmable LED backlight, like
the screen. Refer to section 1.4 LCD
for screen & backlight settings.
Silicon rubber has been chosen for their durability and prompt feedback. The key click can be configured through programming or via System Menu . Refer to
.
1.3.1 24-KEY LAYOUT
The layout of the 24-key keypad is similar to that of a telephone, which includes alphanumeric, navigation and function keys, as well as assorted characters.
Refer to
Appendix III — Key Reference Tables .
Figure 5: 24-key Layout
12
Chapter 1 Using 8500 Mobile Computer
This alphanumeric keypad is set to numeric mode by default. The [ALPHA] key serves as a toggle among numeric, alpha (lower-case alphabetic), and ALPHA (upper-case alphabetic) input modes.
Note: It is not necessary to hold down the [ALPHA] key.
The alpha icon will appear on the lower-left corner of the screen in a sequence as shown below.
Status Icon Alpha Key
(none) N/A
A
Press one time a
Press two times
Input Mode
Numbers
Upper-case alphabetic
Lower-case alphabetic
When in alpha mode, it takes turns to show alphabets and number when you keep pressing the same key; each press must not exceed one second. For example, keep pressing the number key [2], it will take turns to show “A”, “B”, “C” or “2” for upper-case, and “a”, “b”, “c” or “2” for lower-case.
When you first press the number key [2], it will produce the letter “A” or “a”.
When you press the number key [2] twice (the time interval must not exceed one second), it will produce the letter “B” or “b”.
When you press the number key [2] three times (the time interval between each press must not exceed one second), it will produce the letter “C” or “c”.
When you press the number key [2] four times (the time interval between each press must not exceed one second), it will produce the number “2”.
In order to get the desired character, you will need to press the same key, one to four times (the time interval between each press must not exceed one second). Only when you stop pressing the same key for longer than one second or you press another key, will the system send the real key code to the application program.
Yellow-coded alphabetic letter printed at the side
The [FN] key works with a number key. Press the function key, and its associated icon will be displayed on the screen. Press the second key, say [5], to complete the key combination and access the function [F5]. The icon will go off automatically.
13
8500 Series Mobile Computer Reference Manual
Below briefly describes the functions of common keys on the mobile computer.
SCAN
This yellow key is used to trigger the scan engine so that it can read a barcode when the reader function is enabled.
ENTER
The two keys on each side of the SCAN key are user-friendly and convenient for either right-handed or left-handed operator.
Normally, it is used for command execution or input confirmation.
When is pressed, they can be used to alternately turn ON/OFF the backlight of LCD and keypad.
Navigation Keys
These keys are used to move the cursor left, up, down, or right.
While pressing , they can be used to adjust the luminosity and contrast of the screen backlight.
ESC (Escape)
Normally, this key is used to stop and exit the current operation.
BkSp (Backspace)
If this key is being held down for more than one second, a clear code will be sent.
ALPHA (Alpha)
This key is a modifier key that requires pressing a second key to get the yellow-coded letter (A~Z) or symbol printed on the lower side of the second key.
Icon Description
A This icon appears when you press the alpha key once, indicating it is set to alphabetic mode for typing upper-case alphabetic letters. a This icon appears when you press the alpha key twice, indicating it is set to alphabetic mode for typing lower-case alphabetic letters.
14
Chapter 1 Using 8500 Mobile Computer
FN (Function)
This key is a modifier key that requires pressing a second key ([0] ~ [9]) to get the value of key combination.
Icon Description
By default, the function toggle is set to Auto Resume mode, and its behavior is as described below:
This icon appears when you press the function key, indicating it is set to the function mode. Then, press a second key to get the desired function.
The icon will go off automatically.
POWER Key
In order to prevent an accidental press of the POWER key, you need to hold down this key for approximately 1.5 seconds to turn ON/OFF the mobile computer.
Note: (1) Functionality of keys is application-dependent. The system will send the associated key code to the application program, and it is up to the application program to interpret the key code.
(2) When a status icon appears on the screen, it indicates a certain mode is activated and it is not necessary to hold down the modifier key.
15
8500 Series Mobile Computer Reference Manual
1.3.2 44-KEY LAYOUT
The layout of the 44-key keypad includes numeric, alphabetic, navigation and function keys, as well as assorted characters and modifier keys.
Refer to
Appendix III — Key Reference Tables for color-coded keys.
Figure 6: 44-key Layout
The red modifier key works with a key on which red-coded function or symbol is printed on the upper side. Press the red key, and its associated icon will be displayed on the screen. Press the second key, say [AB], to complete the key combination and access the function F1.
The icon will go off automatically.
Red-coded function or symbol printed to the upper
side
16
Chapter 1 Using 8500 Mobile Computer
Below briefly describes the functions of common keys on the mobile computer.
SCAN
This yellow key is used to trigger the scan engine so that it can read a barcode when the reader function is enabled.
ENTER
The two keys on each side of the SCAN key are user-friendly and convenient for either right-handed or left-handed operator.
Normally, it is used for command execution or input confirmation.
When the red modifier key is pressed, they can be used to alternately turn
ON/OFF the backlight of LCD and keypad.
Navigation Keys
These keys are used to move the cursor left, up, down, or right.
While pressing the red modifier key , they can be used to adjust the luminosity and contrast of the screen backlight.
ESC (Escape)
Normally, this key is used to stop and exit the current operation.
BkSp (Backspace)
If this key is being held down for more than one second, a clear code will be sent.
Space
This key is used to insert a blank space.
Tab
Ins (Insert)
This key is used to insert a tab.
This key is used to turn on/off the insert mode.
Del (Delete)
This key is used to delete the character to the right of the cursor.
17
8500 Series Mobile Computer Reference Manual
Shift Key
The alphabetic keypad is set to upper-case alphabetic mode by default. The [Shift] key serves as a toggle between lower-case and upper-case alphabetic input modes.
It takes turns to show alphabets or symbols when you keep pressing the same key, one to two times (the time interval between each press must not exceed one second).
Icon Description
This icon appears when you press [Shift] to set the alphabetic mode to lower-case alphabetic letters.
Alt Key
This key is a modifier key that modifies the next key pressed. The functionality depends on software application.
Icon Description
This icon appears when you press [Alt] to enter the special function mode.
Red Modifier Key
This key is a modifier key that requires pressing a second key to get the red-coded function (F1~F12, Home, End, PgUp, PgDn) or symbol printed to the upper side of the second key.
In order to get the desired symbol, such as “?”, “/” or “\”, you must hold down the red modifier key and keep pressing the symbol key, one to two times (the time interval between each press must not exceed one second). The icon will not appear on the screen.
Icon Description
By default, the function toggle is set to Auto Resume mode, and its behavior is as described below:
This icon appears when you press the red modifier key, indicating it is set to the function mode. Then, press a second key to get the desired function.
The icon will go off automatically.
POWER Key
In order to prevent an accidental press of the POWER key, you need to hold down this key for approximately 1.5 seconds to turn ON/OFF the mobile computer.
Note: (1) Functionality of keys is application-dependent. The system will send the associated key code to the application program, and it is up to the application program to interpret the key code.
(2) When a status icon appears on the screen, it indicates a certain mode is activated and it is not necessary to hold down the modifier key unless a specific red-coded symbol (?, /, \) is desired.
18
1.3.3 44-TE KEY LAYOUT
Chapter 1 Using 8500 Mobile Computer
The layout of the 44-TE key keypad includes numeric, alphabetic, navigation and function keys, as well as modifier keys.
Refer to
Appendix III — Key Reference Tables for color-coded keys.
Figure 7: 44-TE key Layout
19
8500 Series Mobile Computer Reference Manual
This alphanumeric keypad is set to numeric mode by default. The [Alpha] key serves as a toggle among numeric, alpha (lower-case alphabetic), and ALPHA (upper-case alphabetic) input modes.
Note: It is not necessary to hold down the [Alpha] key.
The alpha icon will appear on the lower-left corner of the screen in a sequence as shown below.
Status Icon Alpha Key
(none) N/A
A Press one time a Press two times
Input Mode
Numbers
Upper-case alphabetic
Lower-case alphabetic
The blue modifier key works with a key on which blue-coded function or symbol is printed on the upper-right corner. Press the blue key, and its associated icon will be displayed on the screen. Press the second key, say [F6], to complete the key combination and access the function [F16]. The icon will go off automatically.
Red-coded alphabetic letter printed above the upper-left corner
Blue-coded function or symbol printed to the
upper-
right corner
20
Chapter 1 Using 8500 Mobile Computer
Below briefly describes the functions of common keys on the mobile computer.
SCAN
This yellow key is used to trigger the scan engine so that it can read a barcode when the reader function is enabled.
ENTER
The two keys on each side of the SCAN key are user-friendly and convenient for either right-handed or left-handed operator.
Normally, it is used for command execution or input confirmation.
When the blue modifier key is pressed, they can be used to alternately turn
ON/OFF the backlight of LCD and keypad.
Navigation Keys
These keys are used to move the cursor left, up, down, or right.
While pressing the blue modifier key , they can be used to adjust the luminosity and contrast of the screen backlight.
ESC (Escape)
Normally, this key is used to stop and exit the current operation.
BkSp (Backspace)
If this key is being held down for more than one second, a clear code will be sent.
Space
This key is used to insert a blank space.
Tab
Ins (Insert)
This key is used to insert a tab.
This key is used to turn on/off the insert mode.
Del (Delete)
This key is used to delete the character to the right of the cursor.
21
8500 Series Mobile Computer Reference Manual
Alpha Key
This key is a modifier key that requires pressing a second key to get the red-coded letter (A~Z) printed on the upper-left corner of the second key.
Icon Description
A a
This icon appears when you press the [Alpha] key once, indicating it is set to alphabetic mode for typing upper-case alphabetic letters.
This icon appears when you press the [Alpha] key twice, indicating it is set to alphabetic mode for typing lower-case alphabetic letters.
Alt Key
This key is a modifier key that modifies the next key pressed. The functionality depends on software application.
Icon Description
This icon appears when you press [Alt] to enter the special function mode.
Blue Modifier Key
This key is a modifier key that requires pressing a second key to get the blue-coded function (F16~F24) or symbol printed on the upper-right corner of the second key.
Icon Description
By default, the function toggle is set to Auto Resume mode, and its behavior is as described below:
This icon appears when you press the red modifier key, indicating it is set to the function mode. Then, press a second key to get the desired function.
The icon will go off automatically.
POWER Key
In order to prevent an accidental press of the POWER key, you need to hold down this key for approximately 1.5 seconds to turn ON/OFF the mobile computer.
Note: (1) Functionality of keys is application-dependent. The system will send the associated key code to the application program, and it is up to the application program to interpret the key code.
(2) When a status icon appears on the screen, it indicates a certain mode is activated and it is not necessary to hold down the modifier key.
22
1.4 LCD
Chapter 1 Using 8500 Mobile Computer
The mobile computer comes with a 3” FSTN graphic LCD, 160 by 160 pixels resolutions, which can be programmed to display text or graphics, such as specific font and company logo, to meet varying application needs.
Options
English font
Font Size (pixels)
Font size 6×8 (pixels)
Font size 8×16 (pixels)
Characters by lines
26 characters by 19 lines
20 characters by 9 lines
Chinese font Font size 16×16 (pixels) 10 characters by 9 lines
Other language fonts, company logo… Programmable
Note: The bottom line (ICON_ZONE) is reserved to display status icons, such as the battery icon.
1.4.1 ADJUSTING THE BACKLIGHT
The backlight of screen and keypad helps ease reading under dim environments. It can be turned on and adjusted decreasingly or increasingly by the following key combinations.
Keep pressing the key combination until the luminosity or contrast is decreased or increased to a desired level.
Note: Using backlight while on battery power will substantially reduce battery power. We suggest that you dim the backlight while working in a well-lit area or have it set to be automatically turned off when not in use.
Key Combination
+ [Enter]
+ [Up]
+ [Down]
+ [Right]
+ [Left]
+ [Enter]
+ [Up]
+ [Down]
+ [Right]
+ [Left]
Action
44-TE
+ [Enter] Toggle ON/OFF the backlight
Turn ON the backlight and increase the contrast of LCD
+ [Down] Turn ON the backlight and decrease the contrast of LCD
[Right] Turn ON the backlight and increase the luminosity of LCD
+ [Left] Turn ON the backlight and decrease the luminosity of LCD
+ [3]
+ [6]
Same as
Same as
+ [Up]
+ [Down]
Note: Hold down the first key, and press the second key for adjustment.
23
8500 Series Mobile Computer Reference Manual
1.4.2 CALIBRATING THE SCREEN
This LCD is also a touch screen, which enables the use of a stylus for handwriting. It also features signature capture that can save signature as confirmation of receipt when delivering goods to door.
Refer to 3.2.8 Screen Calibration for screen & contrast calibration.
Warning: DO NOT use any pointed or sharp objects to move against the surface of the screen.
24
1.5 NOTIFICATIONS
Chapter 1 Using 8500 Mobile Computer
1.5.1 STATUS LED
The dual-color LED above the [SCAN] trigger is used to provide information on the charging status and can be programmed to provide information that helps diagnosing.
For example, if you are using AG Runtime, you will be informed of the scanning result immediately. The green LED is used for "Good Read" upon reading a barcode successfully.
LED: Red/Green
Charging 8500
Charging done
Good Read
Error occurs
Red
On
---
---
On
Green
---
On
On
---
1.5.2 AUDIO
The mobile computer has a low power transducer type buzzer, which can be programmed for status feedback. In particular, its frequency and duration are software programmable for Good Read in the provided terminal emulation programs.
1.5.3 VIBRATOR
The mobile computer is integrated with a vibrator, which can be programmed for status feedback. It can be helpful when working in noisy environments. In particular, the vibrator is software programmable for Good Read in the provided terminal emulation programs.
25
8500 Series Mobile Computer Reference Manual
1.6 DATA CAPTURE
Options of different reader combination are allowed, such as 1D+RFID and 2D+RFID. For each combination, both readers can be initialized and ready for scanning at the same time (dual mode operation). For example, if you press the [SCAN] trigger while running the preloaded AG runtime on the mobile computer, it will read a barcode in position or an
RFID tag in proximity depending on which one comes first.
Note: You cannot have 1D+2D scan engines installed on the mobile computer because they are both barcode readers!
Varying by the reader type installed, the supported symbologies or tag types are listed below.
1D CCD scan engine
1D Laser scan engine
1D Long Range Laser scan engine (LR)
1D Extra Long Range Laser scan engine (ELR)
2D scan engine
RFID reader
1.6.1 SYMBOLOGIES SUPPORTED
A wide variety of scan engines is available for delivering flexibility to meet different requirements. Depending on the scan engine integrated, the mobile computer is capable of scanning barcodes of a number of symbologies that are enabled by default while
running the preloaded AG runtime. Refer to 3.3.1 Reader
for functional test.
If you need to scan barcodes that are encoded in a symbology, which is disabled by default in AG runtime, FORGE Application Generator (ForgeAG.exe) allows configuring symbology settings, as well as reader settings. First, enable the desired symbologies, and then, download the application settings to the mobile computer.
Note: In AG or CipherNet runtime, not all of the symbologies are enabled by default.
Instead of running any of them, you can develop your own applications to control the scan engine for data collection. For details on configuring reader and symbology settings, please refer to the documentation of the software you use.
Symbologies Supported (Default Setting: Enable/Disable) CCD/Laser LR/ELR
Codabar
2D
Enabled Enabled Enabled
Enabled Code 11
Code 93
Composite
Code
TCIF Linked Code 39 Enabled
26
Chapter 1 Using 8500 Mobile Computer
MSI
Plessey Disabled
Postal Codes Enabled
Telepen
Code 128 Code 128
Disabled
Enabled Enabled Enabled
Code 2 of 5
Code 3 of 9
GS1-128 (EAN-128)
ISBT 128
Industrial 25 (Discrete 25)
Interleaved 25
Matrix 25
Code 39
Trioptic Code 39
Italian Pharmacode (Code 32)
French Pharmacode
Enabled
Enabled
Enabled
Enabled
Disabled
Enabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
EAN/UPC
EAN-8 Addon 2
EAN-8 Addon 5
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
EAN-13 & UPC-A Addon 2
EAN-13 & UPC-A Addon 5
Bookland EAN (ISBN)
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
UPC-E Addon 2
UPC-E Addon 5
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
GS1 DataBar
(RSS)
GS1 DataBar Omnidirectional
(RSS-14)
GS1 DataBar Truncated
Disabled Enabled Enabled
Disabled Enabled Enabled
GS1 DataBar Stacked Disabled Enabled Enabled
GS1 DataBar Stacked Omnidirectional Disabled Enabled Enabled
GS1 DataBar Limited (RSS Limited) Disabled
GS1 DataBar Expanded (RSS
Expanded)
Enabled Enabled
Disabled Enabled Enabled
GS1 DataBar Expanded Stacked Disabled Enabled Enabled
2D
Symbologies
MicroPDF417 Enabled
27
8500 Series Mobile Computer Reference Manual
Data Matrix Enabled
QR Code
1.6.2 RFID TAGS SUPPORTED
Enabled
The RFID reader supports read/write operations depending on the tags. The supported labels include ISO 15693, Icode®, ISO 14443A, and ISO 14443B. Currently, the performance of some tags has been confirmed, and the results are listed below for your reference. Refer to
3.3.9 RFID for functional test.
Note: You should study the specifications of RFID tags before use.
RFID Module Version 1.0
ISO 14443A Mifare Standard 1K
Mifare Standard 4K
Mifare Ultralight
Mifare DESFire
Mifare S50
SLE44R35
ISO 14443B
ISO 15693
SLE66R35
SRIX 4K
SR176
ICODE SLI
SRF55V02P
SRF55V02S
SRF55V10P
TI Tag-it HF-I
ICODE ICODE®
(Phillips)
9
9
9
9
9
9
9
9
9
9
9
9
UID Only
9
9
9
Read Page
9
9
9
Write Page
9
9
9
--- ---
9 9
--- ---
9 9
9
9
9
9
9 9
--- ---
--- ---
--- ---
9 9
9 9
28
1.7 CHARGING & COMMUNICATIONS
Chapter 1 Using 8500 Mobile Computer
You can use a cradle or charger to charge the mobile computer and/or its battery.
1.7.1 CRADLE OPTIONS
A variety of cradles are available to meet different requirements. The cradle is designed for charging and communications at the same time. You may choose a cradle type that best suits your needs.
Task
Charging
Cradle Interface
6 V charging from the adaptor
Communications Depends on the cradle type and its associated settings — RS-232
Modem
Ethernet
Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It is recommended to charge the battery at room temperature (18°C to 25°C) for optimal performance.
1) Seat the mobile computer in the cradle.
2) Connect the power supply cord to the power receptacle on the back of the cradle.
3) Connect the other end of the power cord to a suitable power outlet.
4) Connect the RS-232 cable if data transmission is required.
Refer to the separate manual for configuring your cradle.
Figure 8: Setting up cradle
29
8500 Series Mobile Computer Reference Manual
Charging & Communication Cradle
3
No. Description
1 LED Indicators (from left to right):
Charging
Receive Data
Transmit Data
Power
Refer to 1.7.2 Understanding the LED
.
Power Jack
No. Description
2 Cable Connector (RS-232)
30
Chapter 1 Using 8500 Mobile Computer
Modem Cradle
Delivering flexibility in making a connection, the Modem Cradle integrates the modem functionality (56 kbps) into the cradle. You may choose to use the modem or RS-232 port by sliding the DIP switch.
Modem Connection
To use the modem functionality, slide the DIP switch to right:
When the power cable is properly connected, the LED light of POWER on the front panel will be solid red.
RS-232 Connection
To use the RS-232 port, slide the DIP switch to left:
When the power cable is properly connected, the LED light of POWER on the front panel will be solid green.
5
No. Description
1 LED Indicators (from left to right):
Charging
Receive Data
Transmit Data
Power
Refer to 1.7.2 Understanding the LED
.
3 Phone Jack
DIP Switch (RS-232/Modem)
No. Description
2 Cable Connector (RS-232)
4
6
Line Jack
Power Jack
31
8500 Series Mobile Computer Reference Manual
Ethernet Cradle
Refer to the Ethernet Cradle manual for more information.
Auto-detect Connection
Slide the DIP switch to left:
The RS-232 connection will override Ethernet connection when both are present. However, you can use cradle commands to switch in between the two.
When the power cable is properly connected, the LED light of POWER on the front panel will be solid green.
LAN Connection
Slide the DIP switch to right:
Only the Ethernet connection can be established. However, you can use cradle commands to switch in between the two.
When the power cable is properly connected, the LED light of POWER on the front panel will be solid red.
5
No. Description
1 LED Indicators(from left to right):
Charging
Receive Data
Transmit Data
Power
Refer to 1.7.2 Understanding the LED
.
3 IP Reset Switch
DIP Switch (Auto/LAN)
No. Description
2 Cable Connector (RS-232)
4
6
Ethernet Port (RJ-45)
Power Jack
32
1.7.2 UNDERSTANDING THE LED INDICATORS
Chapter 1 Using 8500 Mobile Computer
For charging status of the loaded battery in the mobile computer, view the device screen.
Figure 9: Cradle LEDs
Indicator
(Spare battery charging)
Status Description
Off
Red, solid
Battery not ready
Charging
Green, solid Charging done
Red/green, flashing Error occurs
RX (Receive data)
Red, solid Receiving data from Ethernet or host
TX (Transmit data)
Red, solid Transmitting data to Ethernet or host
POWER
Green, solid
Red, solid
Direct connection via RS-232
Modem/Ethernet connection
Warning: Charging error may occur due to a power failure or defected battery contacts.
33
8500 Series Mobile Computer Reference Manual
1.7.3 4-SLOT BATTERY CHARGER
Below is the 4-Slot Battery Charger.
1) The Battery Charger can be mounted on table or wall. Drill two holes (centers spaced
160 millimeters apart), secure the two supplied screws, and mount the Battery
Charger by sliding over screws.
2) Slide the battery pack into the compartment at a proper angle (30°~45°) so that the metal contacts on the battery are met with the charging contacts inside the compartment.
3) Connect the power supply cord to the power receptacle on the charger. Connect the other end of the power supply cord to a suitable power outlet.
4) Press the power switch on, and the Battery Charger’s LED will be red.
5) While charging, the LED of the battery compartment will be red. When fully charged, the LED will be green.
Figure 10: 4-Slot Battery Charger
Indicator
Power
Battery Charging
Status
Red, solid
Off
Red, solid
Green, solid
Red/green, flashing
34
Description
Power on
Battery not ready
Charging
Charging done
Error occurs
Chapter 2
LEARNING SOFTWARE ARCHITECTURE
This chapter mainly describes the software inside the mobile computer. It consists of three modules — Kernel, System, and Application; each has a function menu.
When a menu is displayed, you may select an item by either of the following ways:
Press the arrow keys [Up] and [Down] to move the highlight bar.
Press the number key that corresponds to the item number.
Use the stylus to tap that item or the item number
Follow the on-screen instructions to change a specific setting, or press [ESC] to return to a previous page or menu.
35
8500 Series Mobile Computer Reference Manual
On each screen, the bottom line displays status icons, such as:
The 4-bar battery icon indicates the current power status.
The status icon of input or function mode is controlled by the modifier key.
Icon Description
A / a For 24-key keypad operation, input mode controlled by [ALPHA] key .
For 44-TE key keypad operation, input mode controlled by [Alpha] key .
For 44-key keypad operation, input mode controlled by [Shift] key .
For 24-key keypad operation, function mode controlled by [FN] key .
For 44-key keypad operation, function mode controlled by red key .
For 44-TE key keypad operation, function mode controlled by blue key .
The turn-page icon ( ) indicates there is a previous page or menu.
To return to a previous page or menu, you may press [ESC], touch the menu title, or follow the on-screen instructions.
Figure 11: Software Architecture
IN THIS CHAPTER
2.1 Application Module ..................................................... 37
2.2 System Configuration ................................................. 39
36
2.1 APPLICATION MODULE
Chapter 2 Learning Software Architecture
The mobile computer ships with software package on the CD-ROM. It includes FORGE
Application Generator (batch and WLAN versions), MIRROR Emulator (VT and 5250 versions), download utilities, etc.
2.1.1 FORGE APPLICATION GENERATOR (AG)
For easy development of applications, the mobile computer is preloaded with AG runtime.
When you turn on the mobile computer, it displays the Main Menu of AG application, as shown below.
Batch AG WLAN AG
Note: Batch AG supports automatically uploading data to a host computer when the upload interface is properly configured. Once the mobile computer is seated in the cradle, there will be a moving hourglass icon displayed on the upper-right corner of the screen, indicating the mobile computer is ready for auto upload.
Before using the mobile computer to collect data, you need to configure the application with the companion tool on your computer. This time-saving development tool helps create application templates on your computer.
For details on the AG application, please refer to separate user manual.
Application Generator
Batch AG
WLAN AG
AG Runtime Companion Tool on PC End
U8500.SHX ForgeAG.exe
WU8500.SHX AG8500WLAN.exe
Note: FORGE Application Generator (AG) software package includes
(1) a companion tool for quickly developing your application — Batch or WLAN AG;
(2) several download utilities to make it versatile in use.
37
8500 Series Mobile Computer Reference Manual
2.1.2 MIRROR EMULATOR (CIPHERNET)
The mobile computer supports VT100/220 and IBM 5250 terminal emulation for accessing a backend database. Instead of using FORGE Application Generator , you may download the terminal emulation program, i.e. CipherNet Runtime, to the mobile
computer. Refer to 3.6 Load Program . Then, run individual companion tool on your
computer.
For details on the MIRROR Emulator application, please refer to separate user manuals.
Terminal Emulation
VT100/220
IBM 5250
2.1.3 USER PROGRAM
CipherNet Runtime Companion Tool on PC End
85xx-VT.SHX CipherNet-VT.exe
85xx-5250.SHX CipherNet-5250.exe
You may need to develop your own application program. For developing custom applications, CipherLab provides BASIC and C compilers through licensing. For detailed information, please contact your sales representative.
38
2.2 SYSTEM CONFIGURATION & CORE
Chapter 2 Learning Software Architecture
For managing system configurations and multiple programs, each mobile computer comes with the System Menu , Program Manager , and Kernel . Refer to the following chapters on how to configure the 8500 Series Mobile Computer, regarding system configurations and program download.
2.2.1 SYSTEM MENU
is bundled with BASIC Runtime or user programs that are written in “C”. It is provided for system configuration, functionality testing, downloading font file and program.
2.2.2 KERNEL
Kernel is the innermost core of the OS. It provides services for downloading the active
application program or font file, updating the kernel and configuring Bluetooth settings.
2.2.3 PROGRAM MANAGER
is part of the kernel. You may download as many as seven application programs, or six programs plus one font file.
39
8500 Series Mobile Computer Reference Manual
40
Chapter 3
SYSTEM MENU
System Menu is generated by a powerful utility, which offers an interface for engineers
(programmers or system integrator) to view system information, change the configuration parameters, download programs and run diagnostics.
This menu is designed for engineering tests and maintenance ONLY. For this reason, it provides password protection to prevent unauthorized users from accidentally changing system settings.
Warning! System Menu is NOT for the use of any end users. The system password helps ensure system safety and integrity.
How to access the System Menu?
1) Turn off the mobile computer.
2) Press [7] + [9] + [Power].
41
8500 Series Mobile Computer Reference Manual
IN THIS CHAPTER
3.1 Information............................................................... 42
3.2 Settings ................................................................... 44
3.3 Tests ....................................................................... 47
3.4 Memory.................................................................... 49
3.5 Power ...................................................................... 50
3.6 Load Program............................................................ 51
3.7 Bluetooth Menu ......................................................... 53
3.8 Serial PPP Menu......................................................... 63
3.9 IR Network Menu ....................................................... 66
3.10 Wi-Fi Menu.............................................................. 69
3.1 INFORMATION
Here provides important system information to help diagnose the system.
M/D
KNL
LIB
BSC
USR
DEV
System Menu | 1. Information
H/W
S/N
Hardware version
A serial number assigned to the mobile computer
Manufacturing date
Kernel version
C library version
BASIC Run-time version, if a BASIC application is downloaded
Application program version
RFID
5-digit code for optional hardware configurations
For example, 1410-1 indicates the 44-key mobile computer is equipped with
CCD scan engine, RFID reader, Bluetooth module, and 802.11b/g connectivity.
RFID module version if present; the 3 rd digit of the above Device Code must be 1
42
3.1.1 UNDERSTANDING DEVICE CODE
Chapter 3 System Menu
Device Code Modular Component Types
1st digit Reader module 0= none
2nd digit
3rd digit
4th digit
Wireless module
RFID module
Reserved
1= CCD scan engine
2= Laser scan engine
3= 2D scan engine
4= Long Range Laser scan engine
5= Extra Long Range Laser scan engine
4= Bluetooth + 802.11b/g
5= Bluetooth only
0= none
1= RFID reader
0
5th digit Keypad layout 0= 24-key
1= 44-key
2= 44-TE key
(8570)
(8500)
43
8500 Series Mobile Computer Reference Manual
3.2 SETTINGS
You can change the default settings here.
System Settings
Clock
Backlight Period
Auto Off
Power On Options
Key Click
System Password
Font
Reset to Default
Reset Reader
Default Values
Current time
20 seconds, Level 2
10 minutes
Program Resume
Tone 2
Open access
System font
Load factory settings
Restore default reader settings of 2D or (Extra) Long Range Laser scan engine
Disabled LCD Heater
3.2.1 CLOCK
Set date and time for Real Time Clock. Enter two digits for the year, e.g. 04 for 2004.
3.2.2 BACKLIGHT PERIOD
Set the backlight duration for the keypad and LCD.
Enter a value between 0 and 9999 (second).
Press the arrow keys [Up] and [Down] to adjust the backlight level (4 levels).
3.2.3 AUTO OFF
The mobile computer will be turned off automatically when no operation is taking place during a specified period of time. Enter a value between 0 and 999 (minute).
Note: To disable this function, enter 0.
44
3.2.4 POWER ON OPTIONS
Chapter 3 System Menu
Set the startup screen once the mobile computer is turned on. Press the arrow keys [Up] and [Down] to select “[0] Program Resume” or “[1] Program Restart”, and then press
[ENTER].
Program Resume: When selected, the mobile computer will start from the last session of program before it is turned off.
Program Restart: When selected, the mobile computer will start from the first session of the program.
3.2.5 KEY CLICK
The system will produce an audible signal when any key on the keypad is pressed. The current value is highlighted. Select a desired tone for the buzzer or mute it.
3.2.6 SYSTEM PASSWORD
Set a password to control user access to the System Menu , Program Manager and
Kernel Menu . The password can be up to eight alphanumeric characters.
Note: The password is case-sensitive. To disable a previous password, enter blank on the "Input new password" and "Verify password" screens.
3.2.7 FONT
Font version information can be viewed here. It displays System Font if there is no custom font file. If a multi-language font file is downloaded, you will be able to select a font from the list.
3.2.8 SCREEN CALIBRATION
The cross mark will appear on the four corners of the screen for alignment. Use the tip of the stylus to tap at the center of the cross mark firmly and accurately.
for screen & backlight settings.
Warning: DO NOT use any pointed or sharp object to move against the screen.
3.2.9 RESET TO DEFAULT
Reset system settings to the default values, except for the reader settings.
45
8500 Series Mobile Computer Reference Manual
3.2.10 RESET READER
Reset reader settings to the default values when one of the following scan engines is installed for use:
2D scan engine
Long Range Laser scan engine
Extra Long Range Laser scan engine
3.2.11 LCD HEATER
Set the heater functionality. When enabled, it will start to heat when the environmental temperature falls below -10 Celsius degrees.
46
3.3 TESTS
Here provides functional tests for key parts.
Chapter 3 System Menu
3.3.1 READER
Test the reading performance of the scanner. The supported symbologies depend on the scan engine you use. Refer to
for symbologies that are enabled by default. For symbologies that are disabled by default, they must be enabled through programming.
Press [SCAN] to start. To stop and exit the test, press any key.
3.3.2 BUZZER
Test the buzzer with different frequency/duration combinations.
To stop and exit the test, press any key.
3.3.3 LCD & LED
Test the LCD display and LED indicator.
To stop and exit the test, press any key.
3.3.4 KEYBOARD
Test the rubber keys. Press any key and its corresponding character will be shown on the screen.
To stop and exit the test, press [ESC].
3.3.5 MEMORY
Test the data memory (SRAM), and the results will be shown on the screen.
To stop and exit the test, press [ESC].
Warning! The contents of the data memory (SRAM) will be wiped out after test.
47
8500 Series Mobile Computer Reference Manual
3.3.6 TOUCH SCREEN
Test signature capture by using the stylus for handwriting.
To stop and exit the test, press [ESC] or tap [OK] on the screen.
3.3.7 VIBRATOR
Test the vibrator.
To stop and exit the test, press [ESC].
3.3.8 ECHO TEST
After a physical connection is established properly, run the test utility on your computer and start this test on your mobile computer. Select a desired baud rate if necessary.
To stop and exit the test, press [ESC].
Interface Description Test Utility
IR (Cradle-IR) This echo test is to verify connectivity via IR between the mobile computer and any cradle.
EchoTest.exe
Modem This echo test is to verify connectivity via the Modem
Cradle. A telephone line must be connected to the Modem
EchoTest.exe
Cradle.
Note: For the Modem Cradle, any value other than 57600 bps (default) must be configured through the DIP switch on the IR control board.
3.3.9 RFID
Test the reading performance of the RFID reader when a proximity card is present. Refer to
1.6.2 RFID Tags Supported for the supported RFID tags.
To stop and exit the test, press [ESC].
48
3.4 MEMORY
Chapter 3 System Menu
Here provides information and initialization function of the memory.
3.4.1 SIZE INFORMATION
Base RAM — onboard SRAM for data memory
Memory Card — optional data memory
Flash —
3.4.2 INITIALIZE
Initialize the data memory, Base RAM or Memory Card.
Warning! The contents of the data memory (SRAM) will be wiped out after memory initialization.
49
8500 Series Mobile Computer Reference Manual
3.5 POWER
Here shows current voltage consumption.
Main (battery)
It shows dynamic status of the battery pack, which is used as the main power source.
Backup (battery)
It shows dynamic status of the button cell, which is used to retain data in SRAM.
Warning! Always examine the battery icon on the device screen so that you will be alerted for a low battery condition.
50
3.6 LOAD PROGRAM
Chapter 3 System Menu
Here you can access the
Load Program service provided by the kernel. Because the
kernel will take over the job, you will not be able to return to System Menu by pressing
[ESC]. After downloading, restart the mobile computer to activate the new program.
Refer to
Note: The mobile computer will stay in download mode for approximately 30 seconds.
.SHX Program
Program File
Download one of the following C program files and/or font file:
AG Runtime: U8500.shx (Batch AG)
CipherNet Runtime:
WU8500.shx (WLAN AG)
85xx-5250.shx (CipherNet-5250)
BASIC Runtime Note :
User program
85xx-VT.shx (CipherNet-VT)
B8500.shx
Refer to the Font Files folder on CD-ROM. Font File
If you have downloaded a BASIC Runtime program, the next time you enter the Load
Program submenu you will be able to select whether to download a C program (.SHX) or
BASIC program (.SYN).
Note: “Load Basic” menu is only available after you have downloaded a BASIC Runtime program.
51
8500 Series Mobile Computer Reference Manual
SETTINGS
Interface
Options
Cradle-IR
IrDA
Bluetooth
Baud Rate
Description
Proceed to configure baud rate settings on your computer and the mobile computer.
Point to the target IrDA device.
Approach the target Bluetooth enabled device.
Options
115200 (bps)
76800 (bps)
57600 (bps)
38400 (bps)
19200 (bps)
9600 (bps)
4800 (bps)
2400 (bps)
LOAD PROGRAM VIA BLUETOOTH
Supported by CipherLab software, including download utilities
Yes
Yes
Yes
Yes
Yes
No
No
No
1) Go to System Menu | 7. Bluetooth Menu | 3. Security , and configure the following Bluetooth settings first.
Authentication
PIN code
2) Go to System Menu | 6. Load Program and select Bluetooth.
3) Start the pairing procedure from your computer, for example, click [Pair Device] and/or [Connect Bluetooth Serial Port].
4) Run the download utility: ProgLoad.exe
- Select interface RS-232/IrDA for using Bluetooth SPP.
- Select COM port properties that match with the serial port settings used on your computer.
52
3.7 BLUETOOTH MENU
Chapter 3 System Menu
This submenu is for the mobile computer, with built-in Bluetooth module, to work with other Bluetooth enabled devices. You must configure these parameters correctly.
Note: Due to the fact that the production of 3560 (Bluetooth Access Point) has been discontinued, CipherLab will cease to maintain the Bluetooth PAN (=BNEP) functionality on the mobile computer since the year of 2011.
Bluetooth Settings
Connect Setting
Default Value
Local Name
Remote Name
Broadcast Me
Power Saving
BT-GPRS AP Name
Security
Authentication
Model no. + Serial no.
---
Enabled
Enabled
---
Disabled
PIN Code
Network Setting
---
DHCP Enabled
SubNet Mask
Local IP Address
255.255.128.0
0.0.0.0
Default Gateway
DNS Server
Domain Name
0.0.0.0
0.0.0.0
---
HID SPP DUN
Items Need to Be Checked
---
---
--- v
---
---
--v
--- v v
--- v
---
---
---
--- v
---
--- v v v v
--- v v
(v) Note
---
(v) Note
---
---
--- v v v v
(v) Note v
PAN v
--v
--v v v v v v v
--- v
Note: BT-GPRS AP name, DHCP and local IP Address are required for DUN-GPRS mode only.
53
8500 Series Mobile Computer Reference Manual
3.7.1 INFORMATION
Information of network configuration can be viewed here.
Mask
Gate
Bluetooth Menu | 1. Information
LIB C library version
MAC
IAM
CTY
DHCP
IP
MAC address of the Bluetooth module
A name given to the mobile computer for identification
By default, it is made up of model number and the serial number. (Identical to
2. Connect Set | 1. Local Name)
"Normal" means all 79 channels are available for frequency-hopping
There are bandwidth limitations for 2.4 GHz ISM band in some countries. For example, only 23 RF channels are defined instead of 79 RF channels in Japan,
Spain and France.
DHCP server in use or not
It will automatically become enabled while connecting to a BT-GPRS AP.
IP address of the mobile computer
Subnet Mask
Default Gateway
54
3.7.2 CONNECT SETTING
Set the connection parameters if necessary.
Chapter 3 System Menu
Local Name
Enter a name for identifying the mobile computer.
By default, it is made up of model number and the serial number.
Remote Name
Enter a name for making a specific connection.
The remote name must be one of those in the Freq. Dev. List. Otherwise, the mobile computer will fail to make a connection with any device without pairing.
DO NOT specify any remote name when roaming across different groups of APs is required.
Broadcast Me
Options — Enable or Disable
For initial connection, broadcasting must be enabled so that other Bluetooth devices can discover the mobile computer.
For security concerns, you may disable it in future use to hide the mobile computer from other
Bluetooth devices.
Power Saving
This refers to the low power consumption mode.
Options — Enable or Disable (Only the Sniff mode is supported.)
BT-GPRS AP Name
For DUN-GPRS mode, enter the AP name for connecting to the content server.
55
8500 Series Mobile Computer Reference Manual
3.7.3 SECURITY
Set or modify security parameters.
Authentication
Options — Enable or Disable
PIN Code
Define the encryption key values.
Up to 16 characters, using ASCII code.
Note: When authentication is enabled without providing a pre-set PIN code, the mobile computer supports dynamic input of PIN code during pairing.
56
3.7.4 ECHO TESTS
Chapter 3 System Menu
These echo tests are used for verifying connectivity to make sure the mobile computer is within coverage. Press [ESC] to stop and exit the test.
In PAN mode, the echo test helps measure the coverage of the range, estimate the number of APs and mobile computers needed, and determine the topology of deploying
APs.
SPP: Serial Port Profile
It is used for ad hoc networking, without going through any access point.
DUN: Dial-Up
DUN Modem - It makes use of a Bluetooth modem or mobile phone as a wireless modem.
DUN GPRS – It makes use of a mobile phone with GPRS functionality and connects to GPRS AP.
HID: Human Interface Device Profile
It is used for the mobile computer to work as an input device, i.e. keyboard, for a host computer.
BNEP: Bluetooth
It is used by Personal Area Networking Profile (PAN) for IP networking over
Bluetooth.
57
8500 Series Mobile Computer Reference Manual
SPP Master
Set the mobile computer as a master device.
1. Pairing with your computer (slave) must be completed first.
2. Run the utility “EchoTest.exe” on your computer. Associated settings include
- Select “RS-232” for interface.
- Use the Bluetooth COM port that has been paired.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends. The mobile computer will try to connect to PC (slave).
SPP Slave
Set the mobile computer as a slave device.
1. Enable Authentication and set your PIN code on the mobile computer.
2. Run the utility “EchoTest.exe” on your computer. Associated settings include
- Select “RS-232” for interface.
- Use the Bluetooth COM port that has been configured as “outgoing”.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends.
4. The mobile computer will wait for PC (master) to start the connection.
5. Enter the preset PIN code for authentication on your computer.
DUN Modem
The mobile computer will try to connect to a Bluetooth modem or mobile phone.
1. Pairing with your mobile phone must be completed first.
Select “DialUp Network” for Target Machine options.
2. Run the utility “EchoTest.exe” on your computer. Associated settings include
- Select “Modem” for interface.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends.
4. The mobile computer will connect to your mobile phone that dials up to your computer.
HID Test
Set the mobile computer as an input device.
1. The mobile computer will wait for PC to start the connection.
It is suggested to disable Authentication on the mobile computer.
2. Run a text editor on your computer.
3. Start to input data via the keypad on the mobile computer.
58
Chapter 3 System Menu
DUN GPRS
The mobile computer will try to connect to a mobile phone with GPRS functionality.
1. Pairing with your mobile phone must be completed first.
Select “DialUp Network” for Target Machine options.
2. Run the utility “EchoTest.exe” on your computer. Associated settings include
- Select “TCP/IP – Server” for interface.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends.
4. Enter the server IP and port number on the mobile computer.
5. The mobile computer will connect to your mobile phone that dials up a GPRS AP, and finally connect to your computer (server) through the GPRS AP.
BNEP Client
Set the mobile computer as a client.
1. Pairing with an AP must be completed first.
Select “Access Point” for Target Machine options.
Note that you must disable Authentication and clear the preset PIN code when connecting to
Bluetooth AP (3560).
2. Run the utility “EchoTest.exe” on your computer. Associated settings include
- Select “TCP/IP – Server” for interface.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends.
4. Enter the server IP and port number on the mobile computer. The mobile computer will try to connect to an AP.
BNEP Server
Set the mobile computer as a server.
1. Pairing with an AP must be completed first.
Select “Access Point” for Target Machine options.
Note that you must disable Authentication and clear the preset PIN code when connecting to
Bluetooth AP (3560).
2. Run the utility “EchoTest.exe” on your computer. Associated settings include
- Select “TCP/IP – Client” for interface.
- Enter Remote IP and port number.
- Set Action Mode to “Passive”.
3. Start the echo test on both ends. The mobile computer will try to connect to an AP.
59
8500 Series Mobile Computer Reference Manual
3.7.5 PAIRING TEST
The pairing procedure is for the creation and exchange of a link key between two
Bluetooth-enabled devices. The devices use the link key for future authentication when exchanging information.
1) The mobile computer will start with making an inquiry so that the system can generate a list of device(s) that has been discovered nearby.
2) Select a desired target device.
For the device name, it can only display a maximum length of 11 characters. When the device name is too long, it will be truncated automatically.
3) Select a Bluetooth service from the “Target Machine” menu. To stop and exit the test, press [ESC].
After pairing successfully, the target device will be added to the Frequent Device List for quick connection in the future.
Note: For the initial use of Bluetooth networking, the pairing procedure must be done before the Echo tests.
60
3.7.6 FREQ. DEV. LIST
Chapter 3 System Menu
The Frequent Device List is used to store a list of target device(s) that the mobile computer has been connected to lately. After each successful pairing, the system will update the list.
Note: To unpair any device, simply delete the device from this list.
This list can show information of up to eight target devices that provides different
Bluetooth services. For the device name, it can only display a maximum length of 11 characters. When the device name is too long, it will be truncated automatically.
It can list only one device that provides the Bluetooth Serial Port service. (SPP)
It can list up to eight APs that provide the Bluetooth Personal Area Networking service.
(PAN)
It can list only one device that provides the Bluetooth Dial-Up Networking service.
(DUN)
It can list only one device that provides the Human Interface Device (HID)
However, if you access the list via Kernel Menu , it can only show information of the target device connected via SPP.
Note: During roaming (for PAN only) or re-establishing the connection, the mobile computer will automatically connect to the listed AP(s) or target device without going through the pairing procedure.
61
8500 Series Mobile Computer Reference Manual
3.7.7 NETWORK SETTING
Set parameters for IP networking.
DHCP
Options — Enable or Disable
Subnet Mask
Enter a new Mask IP, if necessary.
Local IP Address
Enter a new address for the mobile computer, if necessary.
Default Gateway
Enter a new address for the default Gateway, if necessary.
DNS Server
Enter a new address for the DNS server, if necessary.
Domain Name
The domain name of the host is displayed when DHCP server is enabled.
Note: Normally, DHCP is enabled and all of the settings can be obtained from the DHCP server.
62
3.8 SERIAL PPP MENU
Chapter 3 System Menu
This submenu is for establishing a PPP connection via the Modem Cradle. You must configure these parameters correctly.
Point-to-Point Protocol (PPP) is a method of connecting the mobile computer to the
Internet over serial links. It sends TCP/IP packets to a server that connects to the
Internet.
3.8.1 INFORMATION
Information of library version can be viewed here.
Serial PPP Menu | 1. Information
LIB C library version
Identical to System Menu | 1. Information
63
8500 Series Mobile Computer Reference Manual
3.8.2 CONNECTION SET
DialUp Number
Enter the number provided by your ISP.
Login Name
Enter the login name provided by your ISP.
Login Password
Enter the login password provided by your ISP.
Baud Rate
Select a desired baud rate.
Note: By default, the baud rate is set to 57600 bps on the Modem Cradle.
For any other value, such as 115200/38400/19200/9600, you must configure through the DIP switch on the IR control board.
64
3.8.3 ECHO TEST
Chapter 3 System Menu
This echo test is used for verifying connectivity via Point-to-Point Protocol. For the
Modem Cradle, its physical connectivity can be verified in System Menu | Tests | Echo
Test | IR or MODEM .
Note: Enter the IP address of a server with which a PPP connection is desired. Then, it will try to connect to the server. After the PPP connection is established properly, run the utility “EchoTest.exe” on your computer (TCP/IP – Server), and then, start this test on your mobile computer.
65
8500 Series Mobile Computer Reference Manual
3.9 IR NETWORK MENU (ETHERNET VIA IR)
This submenu is for establishing an Ethernet connection via IR networking. You must configure these parameters correctly.
Note: The Ethernet Cradle is required for establishing Ethernet connection via IR.
3.9.1 INFORMATION
Information of Ethernet network configuration can be viewed here.
IR Network Menu | 1. Information
DHCP DHCP server in use or not
IP
Mask
Gate
IP address of the mobile computer
Subnet Mask
Default Gateway
66
3.9.2 NETWORK SETTING
Set parameters for IP networking.
Chapter 3 System Menu
DHCP
Options - Enable or Disable
Subnet Mask
Enter a new Mask IP, if necessary.
Local IP Address
Enter a new address for the mobile computer, if necessary.
Default Gateway
Enter a new address for the default Gateway, if necessary.
DNS Server
Enter a new address for the DNS server, if necessary.
Domain Name
The domain name of the host is displayed when DHCP server is enabled.
Note: Normally, DHCP is enabled and all of the settings can be obtained from the DHCP server.
67
8500 Series Mobile Computer Reference Manual
3.9.3 ECHO TESTS
The Ethernet Cradle supports three working modes:
Data Mode
Modem Mode
Transparent Mode
These echo tests are used for verifying connectivity via the Ethernet Cradle. For details, refer to the Ethernet Cradle manual.
Data Mode
Set the Ethernet Cradle in Data mode. The mobile computer works as a client.
Modem Mode
Set the Ethernet Cradle in Modem mode. The mobile computer works as a client.
Transparent Mode
1. Client Mode - Set the mobile computer as a client.
Enter the IP address of a server with which a connection is desired.
2. Server Mode - Set the mobile computer as a server that waits for other devices to connect to.
“EchoTest.exe” on your computer (TCP/IP – Server or Client), and then, start this test on your mobile computer.
68
3.10 WI-FI MENU
Chapter 3 System Menu
This submenu is for 802.11b/g wireless networking. You must configure these parameters correctly.
Wi-Fi Settings
Network Setting
DHCP
SubNet Mask
Local IP Address
Default Gateway
DNS Server
Domain Name
WLAN Setting
Local Name
SS ID
System Scale
Power Saving
Preamble
Ad-Hoc
Fixed BSSID
Security
Authentication
WEP Menu
EAP Menu
WPA Menu
Note: The menu is available only when the Wi-Fi module is present.
Default Value
Enabled
255.255.128.0
0.0.0.0
0.0.0.0
0.0.0.0
---
Model no. + Serial no.
---
Medium
Enabled
Long
Disabled
000000000000
Open System
Disabled
Disabled
Disabled
Ad-hoc Infrastructure
---
---
---
---
---
---
--- v
---
---
--- v
---
Items Need to Be Checked
--- v v v v
--- v v v v v v v v v v v v v
--- v
69
8500 Series Mobile Computer Reference Manual
3.10.1 INFORMATION
Information of network configuration can be viewed here.
Wi-Fi Menu | 1. Information
Ver Firmware version of the Wi-Fi module
MAC
IAM
MAC address of the Wi-Fi module
A name given to the mobile computer for identification.
By default, it is made up of model number and the serial number.
(Identical to 3. WLAN Setting | 1. Local Name)
DHCP server in use or not DHCP
IP
Mask
Gate
IP address of the mobile computer
Subnet Mask
Default Gateway
70
3.10.2 NETWORK SETTING
Set parameters for IP networking.
Chapter 3 System Menu
DHCP
Options — Enable or Disable
Subnet Mask
Enter a new Mask IP, if necessary.
Local IP Address
Enter a new address for the mobile computer, if necessary.
Default Gateway
Enter a new address for the default Gateway, if necessary.
DNS Server
Enter a new address for the DNS server, if necessary.
Domain Name
The domain name of the host is displayed when DHCP server is enabled.
Note: Normally, DHCP is enabled and all of the settings can be obtained from the DHCP server.
71
8500 Series Mobile Computer Reference Manual
3.10.3 WLAN SETTING
Wireless networking can operate in two modes – (1) Ad-hoc mode: peer-to-peer, and (2)
Infrastructure mode: point to multi-point through access points.
Set the following parameters.
Local Name
Enter a name for identifying the mobile computer.
By default, it is made up of model number and the serial number.
SS ID
This refers to Service Set Identifier or AP name, which is used for remote device association.
The mobile computer can ONLY communicate with access points that have the same SS ID.
System Scale
This refers to Access Point Density.
Options — [1] Low [2] Medium [3] High
The value you set must match that set for the access point.
“Low / Medium / High” means the mobile computer will search for other APs only when data transmission rate drops below “1 / 2 / 5” Mbps individually.
Power Saving
This refers to the low power consumption mode.
Options — Enable or Disable
The value you set must match that set for the access point.
Preamble
Options — [1] Long [2] Short [3] Both
The value you set must match that set for the access point.
Ad-Hoc
This refers to peer-to-peer mode, without going through access points.
Options — Enable or Disable
72
Chapter 3 System Menu
Fixed BSSID
This refers to the use of a specific AP’s MAC address as the fixed Basic Service Set Identifier.
The mobile computer can ONLY communicate with this one and only access point.
73
8500 Series Mobile Computer Reference Manual
3.10.4 SECURITY
Set or modify security parameters.
WEP: Wired Equivalent Privacy
EAP: Extensible Authentication Protocol
WPA: Wi-Fi Protected Access
Authentication
[1] Open System
[0] Share Key
Default authentication type
This requires implementing WEP key.
WEP Menu
WEP Setting
WEP Key Length
Default Key
WEP Key
Enabled (For Share Key, it must be enabled!)
Disabled (default)
64 bits
128 bits (default)
WEP KEY1
Enter WEP Keys 1 ~ 4 in one of the following input data type:
ASCII (up to 13 characters)
Hexadecimal (up to 26 characters)
EAP Menu (for associating to Cisco access points)
EAP Setting Enabled
Disabled (default)
EAP ID Enter a user name (up to 32 characters)
EAP Password Enter a password (up to 32 characters)
WPA Menu (WPA-PSK)
WPA Setting
WPA Passphrase
Enabled
Disabled (default)
Enter a phrase as your password (8 ~ 63 characters)
74
3.10.5 ECHO TESTS
Chapter 3 System Menu
This function is used to measure the coverage of the range, estimate the number of APs and mobile computers needed, and determine the topology of deploying APs.
Client Mode
Set the mobile computer as a client. Enter the IP address of a server with which a connection is desired. Then, it will try to connect to an AP.
1. Run the utility “EchoTest.exe” on your computer. Associated settings include
- Select “TCP/IP – Server” for interface.
- Set Action Mode to “Passive”.
2. Start the echo test on both ends.
3. Enter the server IP and port number on the mobile computer.
Server Mode
Set the mobile computer as a server. The mobile computer will try to connect to an AP.
1. Run the utility “EchoTest.exe” on your computer. Associated settings include
- Select “TCP/IP – Client” for interface.
- Set Action Mode to “Passive”.
2. Start the echo test on both ends.
While running echo tests, if WPA setting is enabled for security, the SSID and Passphrase will be processed to generate a pre-share key.
Note: If you change the SSID or Passphrase, it will have to re-generate a pre-share key.
1) For initial association with an access point, you will see an antenna icon developing on the screen to indicate that the mobile computer is processing a pre-share key.
2) After having generated the pre-share key, the mobile computer proceeds to establish a connection with an access point, and you will see the whole antenna is flashing.
3) When the mobile computer has been connected to the access point successfully, you will see the whole antenna and the indication of wireless signal strength.
75
8500 Series Mobile Computer Reference Manual
The changing icon indicates
8500 is processing a pre-share key.
Wait for a few seconds.
The antenna icon will become ready and flashes to indicate 8500 is connecting to an access point under the same SSID.
Once connected, the antenna icon will stop flashing. Next to the icon, the more bars, the stronger the signal.
Note: If you are programming in C or BASIC, be aware that the antenna will appear on the device screen after NetInit() or START TCPIP() is called. (WPA must be enabled first!)
76
Chapter 3 System Menu
Once the connection of echo test is established, the details will be displayed as illustrated below. Link Quality (“Q”) will be the most important element while the others are for your reference.
Q (Link Quality)
0 ~ 10
10 ~ 15
15 ~ 30
50 ~ 80
Very Poor
Poor
Good
Very
Good
T (Transmit Speed)
1
2
5.5
11
6
9
12
18
24
36
48
54
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
Mbps
S (Signal Level)
0 ~ 30
30 ~ 60
Over 60
Weak
Moderate
Strong
N (Noise Level)
1
2 ~ 3
4 ~ 5
Weak
Moderate
Strong
77
8500 Series Mobile Computer Reference Manual
78
Chapter 4
PROGRAM MANAGER & KERNEL
This chapter explains Program Manager and Kernel that manage multiple programs and firmware upgrade.
IN THIS CHAPTER
4.1 Program Manager ...................................................... 79
4.2 Kernel ...................................................................... 84
4.1 PROGRAM MANAGER
The mobile computer supports multiple applications and languages. In the menu of
Program Manager , it allows storing up to seven programs and has one activated for the current use.
If there is no application program exists, the Program Manager will be displayed after you turn on the mobile computer.
Warning! Program Manager is provided for managing programs in an administrative level.
How to access Program Manager?
1) Turn off the mobile computer.
2) Press [8] + [Power].
79
8500 Series Mobile Computer Reference Manual
4.1.1 DOWNLOAD
Here provides a full list of programs that are currently stored on the mobile computer with size information. Multiple application programs can be downloaded through a variety of interfaces. Upon completion of downloading, you are allowed to input a name for the program. If there is no need to rename the program, simply press [ENTER] to leave as it is.
The length of program name can be up to 12 characters. Program size is in kilobytes.
A suffix letter after the memory sector (1 ~ 6) indicates the file type of program.
“b” for BASIC program (.SYN)
“c” for C program (.SHX)
“f” for font file (.SHX)
Note: (1) For a BASIC program (.SYN), it can only be downloaded via System Menu .
(2) In addition to the system font, there can be only one font file downloaded to the mobile computer. The custom font file needs to be downloaded via System
Menu or Kernel Menu .
80
Chapter 4 Program Manager & Kernel
SPARE MEMORY SECTORS (1 ~ 6)
Additional program files can be directly downloaded to these sectors.
Download a program file to an empty sector:
1. Press the arrow keys [Up] and [Down] to select an empty sector, and then press [ENTER].
2. Select a desired interface for downloading.
3. Connect the interface cable if required, and wait for a few seconds to establish a connection…
4. To abort the action, press [ESC]. Then press [ESC] again to return to the menu.
Download a program file to an occupied sector:
If no available sectors, you'll have to replace one program with the new one.
1. Press the arrow keys [Up] and [Down] to select a program that you want to delete, and then press [ENTER].
2. The program information is displayed on the screen.
Press the modifier key [ALPHA] or [Alpha] to enter the Alpha mode:
Press the capital letter [C] and follow the steps below to download a program file.
Press the capital letter [D] if you simply want to delete the program.
3. Select a desired interface for downloading.
4. Connect the interface cable if required, and wait for a few seconds to establish a connection…
5. To abort the action, press [ESC]. Then press [ESC] again to return to the menu.
From the menu, you'll see the program has been deleted but no new program is present
(because you have canceled the download action).
ACTIVE MEMORY SECTOR (“ACT”)
Only the application program, which needs to be activated immediately, can be downloaded to the active memory sector.
Download to Memory Sector “ACT”:
1. Press the arrow key [Down] to select the memory sector “ACT” (may be unoccupied), and then press [ENTER].
2. Select a desired interface for downloading.
3. Connect the interface cable if required, and wait for a few seconds to establish a connection…
If the active memory sector has already been occupied by an application program, the newly downloaded program will replace the currently active program and come into effect immediately.
81
8500 Series Mobile Computer Reference Manual
4.1.2 ACTIVATE
The list shows the entire spare programs stored on the mobile computer. From the list, you can select from the memory sector (1 to 6). The selected program will be copied to the active memory sector and replace the current one.
Note: A font file cannot be activated.
TO CLEAR FILE SYSTEM
When <New Program Start> screen appears, “Press [ESC] to clear file” means the file system in the SRAM will be cleared out by pressing [ESC]. Then there will be no data
(transactions, settings, etc.) stored on the mobile computer when the new program comes into effect.
TO KEEP FILE SYSTEM
To keep the data, simply press any other key.
82
Chapter 4 Program Manager & Kernel
4.1.3 UPLOAD
You may duplicate one or all of the programs from the mobile computer to a host computer or another mobile computer. This can be used to clone software on mobile computers.
Note: To clone all of the programs, the target mobile computer cannot have any other program downloaded except the active one; that is, Memory Sectors 1 ~ 6 must be empty!
The procedures are similar to that for downloading programs.
This screen is not available if you select
“2.All Programs” from the previous screen.
83
84
8500 Series Mobile Computer Reference Manual
4.2 KERNEL
The kernel resides in the innermost core of the system. It has the highest security and is always protected by the system. When the application program is corrupted and System
Menu fails at the same time, Kernel Menu provides an access to fix the system.
Warning! Kernel Menu is NOT for the use of any end users.
How to access Kernel Menu?
1) When the last session is in System Menu or Program Manager , simply turn off the mobile computer. Otherwise, you must reload the battery pack.
2) Press [1] + [7] + [Power].
Chapter 4 Program Manager & Kernel
4.2.1 KERNEL INFORMATION
Here provides important system information to help diagnose the system.
Kernel Menu | 1. Information
H/W
S/N
M/D
Hardware version
Serial number of the mobile computer
Manufacturing date
KNL
DEV
Kernel version
5-digit code for optional hardware configurations
Refer to
.
85
8500 Series Mobile Computer Reference Manual
4.2.2 LOAD PROGRAM
You can download one program file to the active memory sector, as well as one font file to the memory address assigned by the system. After downloading, restart the mobile computer to activate the new program. Refer to
.
New application program or program update
And/or one font file, i.e. multi-language font
If you are using a custom font file rather the system font and you want to download another font file, it is necessary to delete the current font file from the program list
first. Otherwise, downloading new font file is not allowed.
Note: The mobile computer will stay in download mode for approximately 30 seconds.
.SHX Program
Program File
Download one of the following C program files and/or font file:
AG Runtime: U8500.shx (Batch AG)
CipherNet Runtime:
WU8500.shx (WLAN AG)
85xx-5250.shx (CipherNet-5250)
BASIC Runtime Note :
User program
85xx-VT.shx (CipherNet-VT)
B8500.shx
Refer to the Font Files folder on CD-ROM. Font File
If you have downloaded a BASIC Runtime program, the next time you access the Load
service via System Menu , you will be able to select whether to download a C program (.SHX) or BASIC program (.SYN).
Note: Go to System Menu | 6. Load Program | 2. Load Basic , and download a BASIC program (*SYN).
86
Chapter 4 Program Manager & Kernel
SETTINGS
Interface
Options
Cradle-IR (Serial IR)
IrDA
Bluetooth
Baud Rate
Description
Proceed to configure baud rate settings on your computer and the mobile computer.
Point to the target IrDA device.
Approach the target Bluetooth enabled device.
Options
115200 (bps)
76800 (bps)
57600 (bps)
38400 (bps)
19200 (bps)
9600 (bps)
4800 (bps)
2400 (bps)
Supported by CipherLab software, including download utilities
Yes
Yes
Yes
Yes
Yes
No
No
No
Note: If you select to use Serial IR of the Modem Cradle, any value other than 57600 bps (default) must be configured through the DIP switch on the IR control board.
LOAD PROGRAM VIA BLUETOOTH
1) Go to Kernel Menu | 5. Bluetooth Menu | 3. Security , and configure the following
Bluetooth settings first.
Authentication
PIN code
2) Go to Kernel Menu | 2. Load Program and select Bluetooth.
3) Start the pairing procedure from your computer, for example, click [Pair Device] and/or [Connect Bluetooth Serial Port].
4) Run the download utility: ProgLoad.exe
- Select interface RS-232/IrDA for using Bluetooth SPP.
- Select COM port properties that match with the serial port settings used on your computer.
87
8500 Series Mobile Computer Reference Manual
4.2.3 KERNEL UPDATE
The kernel might need to be updated to improve performance or due to other considerations.
To download a kernel update (K*.shx), the procedure is the same as that for downloading a program.
Any attempt to download an older version will be rejected.
The system will restart itself right after downloading.
Warning: Do not turn off the mobile computer while downloading a kernel update or re-starting the mobile computer. Otherwise, it will crash the kernel forever.
There is no way to recover it!
Note: CipherLab software, including download utilities, supports the following baud rate options: 115200/57600/38400/19200/9600 bps.
4.2.4 TEST & CALIBRATE
These tools are provided for manufacturing use.
Warning! You should not perform any of these tests.
4.2.5 BLUETOOTH MENU
for details. This submenu is almost the same as the one provided in System Menu except for a few items.
88
SPECIFICATIONS
Model Designation
Wireless
Communications
Readers
Electrical
Characteristics
Physical
Characteristics
IR/IrDA
Bluetooth Class 2
8500
√
√
8570
√
√
802.11b/g √
Barcode Reader CCD (linear imager)
Standard Laser
Long Range Laser
Extra Long Range Laser
2D Imager
RFID Reader Frequency 13.56 MHz
Main Battery
Working Time
Backup Battery
Power Adaptor
CPU
Memory
Display
Keypad
Indicators
Vibrator
Rechargeable Li-ion battery – 3.7 V, 4000 mAh
Laser, one scan per 5 seconds, with backlight on:
400 hours in batch mode
70 hours in Wi-Fi mode
Rechargeable Lithium button cell – 3.0 V, 7 mAh
Data retention – at least 7 days
Input: AC 100~240 V, 50/60 Hz
Output: DC 6 V, 3.3 A
Operating Temperature: 0 °C to 40 °C
32-bit Toshiba CMOS type, 40 MHz
Program memory – 2 MB flash
Data memory – 2 MB onboard SRAM, upgradeable
(4 or 8 MB optional)
Graphic LCD, 160 x 160 pixels, 3” FSTN with LED backlight programmable
Font size 6x8: 26 characters by 19 lines
Font size 8x16: 20 characters by 9 lines
Also a touch screen allows for the use of stylus for control and signature capture.
24 or 44 rubber keys, LED backlight programmable
LED – Dual-color (red/green), programmable
Buzzer – Low power transducer type, 1 KHz to 4
KHz, programmable
9000 ± 2000 RPM, Max. 50 dB, programmable
Enclosure Material Rubber & ABS plastic
89
8500 Series Mobile Computer Reference Manual
Dimensions
Weight
230 mm (L) 91 mm (W) 65 mm (H)
Approx. 600 g (Laser, battery included)
Environmental
Characteristics
Storage:
-10 °C to 60 °C (8570)
-30 °C to 70 °C
Programming
Accessories
Storage: 5% to 95% non-condensing
Impact Resistance 1.5 m, 5 drops per 6 sides
Splash / Dust
Resistance
IP 64
Electrostatic
Discharge
± 15 kV air discharge, ± 8 kV contact discharge
Development Tools C and BASIC
Software & Utilities FORGE Application Generator (AG), AG utilities;
MIRROR Emulator (CipherNet) for VT100/220, IBM
5250 emulation;
Download utilities, testing tools, etc.
Pistol Grip
Belt Holster
Protective Cover
Spare rechargeable battery pack
4-slot Battery Charger
Charging & Communication Cradle
Modem Cradle (56 K)
Ethernet Cradle (10/100 BASE-T)
Vehicle Cradle
Travel Charger
90
Appendix I
DOWNLOAD UTILITY
For easy development of applications, the mobile computer ships with FORGE
Application Generator programs, batch and WLAN versions, as well as a download utility.
FILE TYPES
Depending on the file type, you may download a program or font file via System Menu ,
Program Manager or Kernel Menu .
File Type
Font file
AG runtime
CipherNet runtime
Kernel update
BASIC program
BASIC runtime
FONT FILE
System Menu
√
√
√
−
√
√
Kernel Menu
√
√
√
√
−
√
Program Manager
−
√
√
−
−
√
Download a font file (.SHX) via System Menu or Kernel Menu .
Font file: Font-Multi-Language.SHX, Font-Japanese.SHX, and so on.
C PROGRAMS
Download a C program (.SHX) via System Menu , Program Manager or Kernel Menu .
AG runtime: U8500.SHX, WU8500.SHX
CipherNet runtime: 85xx-VT.SHX, 85xx-5250.SHX
Kernel update: K*.SHX
Note: You can only download a Kernel update via Kernel Menu .
BASIC PROGRAMS
First, download a BASIC runtime (e.g. B8500.SHX) via System Menu , Program
Manager or Kernel Menu . Then, it will allow you to download a BASIC program (.SYN) via System Menu .
91
8500 Series Mobile Computer Reference Manual
PROGLOAD.EXE
The utility “ProgLoad.exe” is provided for you to download a program (*.SHX or *.SYN) to the mobile computer. Run the program on your computer. The following dialog box pops up.
Click to select Comm type, COM port, and
Baud rate.
Choose your file…
Communication Type
RS-232/IrDA
Cradle-IR
TCP/IP
File Type
.SHX file
.SYN file
Connection via direct RS-232 cable, IrDA port, or Bluetooth SPP
Connection via cradle
Connection over networks
Any C program, such as AG Runtime, Basic Runtime, font file, etc.
Any Basic program after Basic Runtime has been installed first.
92
Appendix II
TROUBLESHOOTING
CANNOT TURN ON WHEN PRESSING POWER KEY
Make sure the battery pack is installed properly.
Re-charge the battery inside the mobile computer and monitor the charging status.
(See
.)
If the battery is faulty, replace it with a fresh and fully charged battery then.
CHARGING ERROR
If using a cradle or charger, make sure the power cord is well connected the cradle/charger and an outlet.
Check if the battery contacts of the battery itself and the battery compartment are clean.
Try to re-charge the battery and monitor the charging status.
Warning! Only use batteries or charging device manufactured by CipherLab. The use of wrong battery or charging device could result in damage to human body or the product itself, and will void your warranty.
BUZZER SEEMS NOT WORKING
Perform the buzzer test. (See
.)
If the problem persists, reload the battery pack and perform the test again.
LED INDICATOR SEEMS NOT WORKING
Perform the LCD & LED test. (See 3.3.3 LCD & LED
.)
If the problem persists, reload the battery pack and perform the test again.
LCD TOUCH SCREEN SEEMS NOT WORKING
Perform the touch screen test. (See 3.3.6 Touch Screen
.)
If the problem persists, reload the battery pack and perform the test again.
KEYPAD SEEMS NOT WORKING
Perform the keyboard test. (See
If the problem persists, reload the battery pack and perform the test again.
93
8500 Series Mobile Computer Reference Manual
VIBRATOR SEEMS NOT WORKING
Perform the vibrator test. (See 3.3.7 Vibrator
.)
If the problem persists, reload the battery pack and perform the test again.
MOBILE COMPUTER SEEMS NOT WORKING
Upload all data to the host and perform the memory test. (See 3.3.5 Memory .)
If the problem persists, reload the battery pack and perform the test again.
CANNOT SCAN BARCODES
LOW BATTERY CONDITION
Check if the battery icon on the screen indicates a low battery status. If so, replace it with a fresh battery then.
If the problem persists, check if the battery contacts get dirty or the battery pack does not fit to the compartment.
BARCODE OR RFID READER PROBLEM
Perform the reader test to see if the reader is working. (See 3.3.1 Reader
.)
If the problem persists, reload the battery pack and perform the test again.
CANNOT DECODE DATA AFTER SCANNING
UNREADABLE BARCODE
Check if the barcode is defaced. A defaced barcode may not be readable.
UN-PROGRAMMED TO READ
Check if the scanner is programmed to read the symbologies (types of barcode) that you are trying to read.
Try scanning a test barcode of the symbology you are trying to read.
DIRTY SCAN WINDOW
Check if the scan window gets dirty. Wipe it with a clean and dry cloth, and try again.
OUT OF SCANNING RANGE
Try adjusting the scanning distance from the scanner to the barcode.
94
CANNOT TRANSMIT/RECEIVE DATA
Appendix II Troubleshooting
VIA IR PORT
Make sure the mobile computer's infrared port is pointed directly to the infrared port of another IR device.
Make sure the distance between the mobile computer and a target device is within proper range, and no obstacles in between. Try to establish connection again.
If the problem persists, run the Echo Test to check if the IR interface between the
mobile computer and the cradle is working. (See 3.3.8 Echo Test
.)
USING RS-232 CABLE VIA CRADLE
Check if the RS-232 connection is correct and secured.
Make sure the serial port parameters on the host are configured to match the serial parameters on the mobile computer. Try to establish connection again.
Make sure the mobile computer is well seated inside the cradle. DO NOT remove the mobile computer or disconnect the cradle before communications are done.
If the problem persists, run the Echo Test to check if the IR interface between the
mobile computer and the cradle is working. (See 3.3.8 Echo Test
.)
VIA BLUETOOTH
Make sure the distance between the mobile computer and a target device is within proper range. Try to establish connection again.
Check if the relevant settings are correct. (See 3.7 Bluetooth Menu
.)
If the problem persists, run the Echo Test to check if the connection is working properly. (See
VIA WI-FI
Make sure the mobile computer is connected to an access point properly, under the same SSID. Try to establish connection again.
Check if the relevant settings are correct. (See 3.10 Wi-Fi Menu .)
If the problem persists, run the Echo Test to check if the connection is working properly. (See
.)
VIA ETHERNET CRADLE
Check if the Ethernet connection is correct and secured.
Make sure the networking parameters are configured properly. Try to establish connection again.
Make sure the mobile computer is well seated inside the cradle. DO NOT remove the mobile computer or disconnect the cradle before communications are done.
If the problem persists, run the Echo Test to check if the Ethernet connection is working properly. (See
.)
95
8500 Series Mobile Computer Reference Manual
VIA MODEM CRADLE
Check if the modem connection is correct and secured.
Make sure the modem parameters are configured properly. Try to establish connection again.
Make sure the mobile computer is well seated inside the cradle. DO NOT remove the mobile computer or disconnect the cradle before communications are done.
If the problem persists, run the Echo Test to check if the PPP connection is working properly. (See
If the problem persists, run the Echo Test to check if the IR/MODEM interface between the mobile computer and the cradle is working. (See
96
Appendix III
KEY REFERENCE TABLES
7
8
5
6
9
-
3
4
1
2
0
.
24-KEY KEYPAD
SYSTEM DEFAULTS
Key [ALPHA] key pressed once
[ALPHA] key pressed twice
Key
WXYZ
+$
/*
%#;,
JKL
MNO
PQRS
TUV
Space
ABC
DEF
GHI wxyz
+$
/*
%#;, jkl mno pqrs tuv
Space abc def ghi
7
8
5
6
3
4
1
2
0
.
9
-
[FN] key pressed
[FN] key pressed once twice
F5
F6
F7
F8
F1
F2
F3
F4
F9
-
F10
.
7
8
5
6
3
4
1
2
0
.
9
-
97
YZ
QR
ST
UV
WX
IJ
KL
MN
OP
AB
CD
EF
GH
8500 Series Mobile Computer Reference Manual
44-KEY KEYPAD
SYSTEM DEFAULTS
Key [Shift] key pressed once
[Shift] key pressed twice
Key yz qr st uv wx ij kl mn op ab cd ef gh
YZ
QR
ST
UV
WX
IJ
KL
MN
OP
AB
CD
EF
GH
YZ
,;
$:
QR
ST
UV
WX
IJ
KL
MN
OP
AB
CD
EF
GH
F11
F12
#?
+/
*\
F7
F8
F9
F10
F3
F4
F5
F6
Red key pressed once / held down
F1
F2
98
7
8
5
6
3
4
1
2
0
.
9
-
44-TE KEY KEYPAD
SYSTEM DEFAULTS
Key [Alpha] key pressed once
[Alpha] key pressed twice
Key
G
H
E
F
C
D
A
B
K
L
I
J g h e f c d a b k l i j
7
8
5
6
3
4
1
2
0
.
9
-
Appendix III Key Reference Tables
Blue key pressed once
^
&
[
]
<
>
?
$
%
#
99
F9
F10
F11
F12
F13
F14
F15
F5
F6
F7
F8
F1
F2
F3
F4
8500 Series Mobile Computer Reference Manual
Key [Alpha] key pressed once
[Alpha] key pressed twice
Key
W
X
U
V
Y
Z null
S
T
Q
R
O
P
M
N w x u v y z null s t q r o p m n
F9
F10
F11
F12
F13
F14
F15
F5
F6
F7
F8
F1
F2
F3
F4
Blue key pressed once
F19
F20
F21
F22
F23
F24 null
=
F16
F17
F18
*
/
+
-
100

Public link updated
The public link to your chat has been updated.
Advertisement