advertisement
Safety ......................................................... 2
Specifications ............................................. 8
Setup .......................................................... 8
Operation .................................................... 9
Table of Contents
Maintenance .............................................. 12
Parts List and Diagram .............................. 14
Warranty .................................................... 16
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
General Power Tool Safety Warnings
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term ″power tool″ in the warnings refers to your mains-operated (corded) power tool.
Work area safety
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
Page 2 For technical questions, please call 1-800-444-3353.
ITEM 3273
Electrical safety
1. Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with grounded
power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location is unavoidable, use a Ground Fault Circuit
Interrupter (GFCI) protected supply.
Use of a GFCI reduces the risk of electric shock.
Personal safety
1. Stay alert, watch what you are doing and use common sense when operating a power tool.
Do not use a power tool while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in serious personal injury.
2. Use personal protective equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
3. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Power tool use and care
1. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was designed.
2. Do not use the power tool if the switch/trigger does not turn it on and off.
Any power tool that cannot be controlled with the switch/trigger is dangerous and must be repaired.
3. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust-related hazards.
8. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide adequate protection. Eye protection must be
ANSI-approved and breathing protection must be NIOSH-approved for the specific hazards in the work area.
4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions
to operate the power tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
ITEM 3273 For technical questions, please call 1-800-444-3353.
Page 3
Power tool use and care (cont.)
7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions
and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
Drill Safety Warnings
1. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tools by insulated gripping surfaces when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a ″live″ wire will make exposed metal parts of the tool ″live″ and shock the operator.
3. Let bit cool before touching, changing or adjusting it. Bits heat up dramatically while in use, and can burn you.
4. If the drill bit jams, release the trigger immediately; drill torque can cause injury or break bit.
5. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
6. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
7. Do not lay the tool down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your control.
8. When using a handheld power tool, maintain a firm grip on the tool with both hands to resist starting torque.
9. Do not leave the tool unattended when it is plugged into an electrical outlet. Turn off the tool, and unplug it from its electrical outlet before leaving.
10. This product is not a toy.
Keep it out of reach of children.
11. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
In addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with power switch/trigger locked on.
• Properly maintain and inspect to avoid electrical shock.
• Properly ground power cord. Ground Fault Circuit
Interrupter (GFCI) should also be implemented
– it prevents sustained electrical shock.
12. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.
)
13. WARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of
California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.
)
14. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur.
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Page 4 For technical questions, please call 1-800-444-3353.
ITEM 3273
Vibration Safety
This tool vibrates during use.
Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool.
If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the vibration effects on the user.
4. Use tools with the lowest vibration when there is a choice.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work.
7. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately.
SAVE THESE INSTRUCTIONS.
ITEM 3273 For technical questions, please call 1-800-444-3353.
Page 5
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
Grounded Tools: Tools with Three Prong Plugs
3-Prong Plug and Outlet
2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically
“live” terminal. (See 3-Prong Plug and Outlet.)
3. The tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the preceding illustration.
(See 3-Prong Plug and Outlet.)
1. Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet.
If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See 3-Prong Plug and Outlet.)
Double Insulated Tools: Tools with Two Prong Plugs
Outlets for 2-Prong Plug
1. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies
OSHA requirements and complies with the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.
2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.
(See Outlets for 2-Prong Plug.)
Extension Cords
1. Grounded tools require a three wire extension cord.
Double Insulated tools can use either a two or three wire extension cord.
2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Table A.)
3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Table A.)
4. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Table A.)
Page 6 For technical questions, please call 1-800-444-3353.
ITEM 3273
5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Table A.)
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.
7. Make sure the extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it.
8. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas.
TABLE A: RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS* (120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
0 – 2.0
EXTENSION CORD
LENGTH
25´ 50´ 75´ 100´ 150´
18 18 18 18 16
2.1 – 3.4
3.5 – 5.0
18
18
18
18
18
16
16
14
14
12
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
18
18
14
12
16
14
12
10
14
12
10
-
12
10
-
-
12
-
-
-
* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
V~
Volts Alternating Current
A
Amperes
n0 xxxx/min.
No Load Revolutions per Minute (RPM)
WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields.
Read the manual before set-up and/or use.
WARNING marking concerning Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Properly connect power cord to appropriate outlet.
ITEM 3273 For technical questions, please call 1-800-444-3353.
Page 7
Specifications
Electrical Rating
No Load Speed
Chuck Capacity
Approximate
Work Capacity
120V~ / 60Hz / 6.3A
0-1200 RPM
1/2″ (13mm)
3/4″ Wood
1/2″ Metal
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Assembly
Thread the Auxiliary Handle securely into the left or right side of the Drill.
Functions
Chuck
Ring
Lock
Button
Chuck
Key Hole
Chuck
Jaws
Auxiliary
Handle
Trigger
Direction
Switch
Key Holder
Page 8 For technical questions, please call 1-800-444-3353.
ITEM 3273
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Power Switch/Trigger is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section.
Drill Bit Installation
CAUTION!
Wear heavy-duty work gloves to provide protection when inserting and removing drill bits.
Drill bits become very hot during use.
Do not remove drill bits until the bit has cooled.
1. Loosen the Chuck with the Chuck Key until the jaws of the drill are opened enough to fit the drill bit.
2. Place the desired drill bit or screwdriver bit into the drill between the Chuck Jaws.
Note: In addition to single or double-ended screwdriver bits, adapters with hexagonal shafts with matching socket heads can also be used.
3. Insert the tip of the Chuck Key into a hole on the side of the Chuck so that the teeth on the Key engage the gear on the Chuck. Use the Key to tighten the Chuck securely and remove the Key.
NOTICE: Use sharp bits. Dull, bent, or damaged bits will cause stress on the drill and/or break.
Workpiece and Work Area Set Up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children or pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be objects, such as utility lines, nearby that will present a hazard while working.
ITEM 3273 For technical questions, please call 1-800-444-3353.
Page 9
General Operating Instructions
1. Make sure that the Switch/Trigger is in the off-position, then plug in the tool.
2. Press the Direction Switch of the Trigger to determine the rotation direction. Press to the left side for clockwise rotation. Press to the right side for counterclockwise rotation.
3. Squeeze the Trigger to start the tool. The Trigger has a variable speed feature. Moving the Trigger slightly will make the tool operate slowly, moving the trigger more will cause the tool to operate faster.
4. You can lock the Trigger in the ON position by squeezing the trigger, pressing in the
Lock Button, and releasing the Trigger. The tool will operate continuously. To stop the tool, squeeze and release the Trigger.
5. Use only well-sharpened bits that are in good condition and appropriate to the task.
6. Use firm pressure when drilling, but do not press too hard. Too much pressure will cause the bit to overheat, may cause the bit to bend or break, cause undue strain on the tool, and may damage the workpiece. Pressing too hard may stall the motor.
7. If the motor stalls, release the Trigger immediately to prevent damage to the tool.
8. Only drill in a straight line. Bending or twisting the bit while drilling may cause the bit to bend or break and may damage the workpiece.
9. Back off your pressure if you are about to penetrate the other side of the workpiece.
10. Keep the motor running when pulling the bit out of a completed hole to prevent the bit from jamming.
Page 10 For technical questions, please call 1-800-444-3353.
ITEM 3273
Metal Drilling
1. Use high speed steel, carbide, TiN coated, or specialty bits for metal drilling.
2. Secure the workpiece to keep it from moving during the drilling operation.
3. To make starting the hole easier, use a punch to create a dimple at the hole center.
4. Unless drilling into cast iron or brass use a cutting lubricant.
5. Start by drilling slowly to keep the bit from moving away from your starting point.
Wood Drilling
6. As the hole is established, increase tool speed.
Do not go so fast or use so much pressure that the bit heats up. This can damage the bit and create an irregular hole. For hard metal, use cutting oil to keep the bit cool.
7. Since drilling in metal is a slow operation, you may lock the Trigger in the ON position to maintain a constant speed and reduce fatigue.
8. When drilling large holes in metal, start by drilling a smaller pilot hole, then using a larger bit for the final size hole.
1. Use high speed bits or bits specially designed for wood drilling, such as brad point, spade bits, forstner bits, etc.
2. Secure the workpiece to keep it from moving during the drilling operation.
3. Start by drilling slowly to keep the bit from moving away from your starting point.
Increase speed as the hole is established.
4. To prevent or reduce “break out” when the bit penetrates the workpiece, clamp a piece of scrap material to the back of the workpiece.
5. Do not lock the Trigger in the ON position, as the bit can easily jam in wood and the motor must be stopped quickly.
After Use
To prevent accidents, disengage the trigger, disconnect the tool’s power supply, allow the bit to cool completely, and remove the bit after use. Clean, then store the tool indoors out of children’s reach.
ITEM 3273 For technical questions, please call 1-800-444-3353.
Page 11
Maintenance and Servicing
Procedures not specifically explained in this manual must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Power Switch/Trigger is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general condition of the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• damaged cord/electrical wiring,
• cracked or broken parts, and
• any other condition that may affect its safe operation.
Chuck (1) Replacement
2. AFTER USE, wipe external surfaces of the tool with clean cloth.
3. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician.
1. Release the Trigger and unplug the tool from its electrical outlet.
2. Open the Chuck jaws fully.
3. Remove the Chuck Screw (44) inside the
Chuck Jaws by turning it counterclockwise.
4. Switch the Direction Switch to the reverse direction.
Plug the Power Cord into a suitable outlet.
5. Hold the Chuck ring with a gloved hand and gently squeeze the trigger with your other hand.
6. The Chuck should come off in your gloved hand.
7. Install the new Chuck by reversing the above steps.
Carbon Brush Service
If the Carbon Brushes are damaged or worn, they must be replaced by a qualified service technician. Improper service may result in the double insulation system being compromised.
Page 12 For technical questions, please call 1-800-444-3353.
ITEM 3273
Troubleshooting
Problem
Tool will not start.
Possible Causes
1. Cord not connected.
2. No power at outlet.
3. Tool’s thermal reset breaker tripped (if equipped).
4. Internal damage or wear.
(Carbon brushes or switch, for example.)
Tool operates slowly. 1. Forcing tool to work too fast.
2. Extension cord too long or cord diameter too small.
Performance decreases over time.
Excessive noise or rattling.
1. Carbon brushes worn or damaged.
2. Bit dull or damaged.
Internal damage or wear. (Carbon brushes or bearings, for example.)
Likely Solutions
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
1. Allow tool to work at its own rate.
2. Eliminate use of extension cord. If an extension cord is needed, use one with the proper diameter for its length and load. See Extension Cords in Grounding section on page 6.
1. Have qualified technician replace brushes.
2. Keep bits sharp. Replace as needed.
Have technician service tool.
Drill bit slips in chuck.
Overheating.
1. Jaws are loose.
2. Bit is jammed in workpiece.
1. Forcing tool to work too fast.
2. Bit dull or damaged.
3. Blocked motor housing vents.
4. Motor being strained by long or small diameter extension cord.
1. Tighten chuck .
2. Tighten chuck, then operate tool in reverse to back bit out of workpiece.
1. Allow tool to work at its own rate.
2. Keep bits sharp. Replace as needed.
3. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while blowing dust out of motor using compressed air.
4. Eliminate use of extension cord. If an extension cord is needed, use one with the proper diameter for its length and load. See Extension Cords in Grounding section on page 6.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
ITEM 3273 For technical questions, please call 1-800-444-3353.
Page 13
Parts List and Diagram
Part
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
17
18
19
20
21
22
23
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List
Description
Chuck
Retaining Ring Ø 32
Iron Bushing
Wool Washer
Spindle
Key 3 x Ø10
Bearing 6002
Screw ST4.2 x 3.5
Washer Ø4
Fender Ring Ø15
Gear Housing
Needle Bearing HK071109
Gear 3
Key 3 x Ø10
Gear 2
Needle Bearing HK071109
Middle Housing
Gear 4
Spring Ø12
Needle Bearing HK081210
Bearing 608
Fan
Rotor
Part
36
37
38
39
32
33
34
35
28
29
30
31
24
25
26
27
40
41
42
43
44
45
Description
Bearing 607
Inner Bearing Cover
Ring Fender
Screw ST4.2 x 50
Washer Ø4
Stator
Rear Housing
Brush Holder Cap
Carbon Brush
Brush Holder
Direction Switch
Handle
Trigger
Screw ST2.9 x 12
Screw ST4.2 x 14
Cord Clamp
Cord
Handle
Screw ST4.2 x 14
Cord Protector
Chuck Screw
Auxiliary Handle (Not Shown)
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
Page 14 For technical questions, please call 1-800-444-3353.
ITEM 3273
Assembly Diagram
ITEM 3273 For technical questions, please call 1-800-444-3353.
Page 15
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
advertisement