jcb JCB-MS-210C Instructions & User's Manual

POWER TOOL

INSTRUCTION & USER MANUAL

JCB-MS-210C

Original Instructions

IM-MS-210C-EN

EN

2 JCB-MS-210C

Instruction & User Manual

GENERAL WARNINGS & DISPOSAL

To reduce the risk of injury, user must read the instruction manual

This symbol is used throughout this manual to warn the user about potential risks. Please read & understand these sections before using the device.

Personal Protective Equipment (P.P.E.) must be worn during the operation of the device.

The device must not be exposed to rain or immersed in water.

Do not allow any part of the device to come into contact with flame, or to catch fire.

Warning!

Risk of injury! Do not touch the moving saw blade!

Protection rating II (double insulated)

This mitre saw is equipped with a class 2 laser.

Do not look into the laser beam

The month and year of manufacture can be found within the product serial number e.g.

MMYYPPPAXXXXX. Where production month (MM) and production year (YY) are included.

JCB-MS-210C

Instruction & User Manual

3

4

Contents

GENERAL SAFETY INSTRUCTIONS

Save all warnings and instructions for future reference

SAFETY INSTRUCTIONS FOR MITRE SAWS

COMPONENT LIST

TECHNICAL DATA

Safty instructions for the handling of saw blades

VIBRATION AND NOISE INFORMATION

OPERATING INSTRUCTIONS

Intended Use

Commissioning

Assembly

Area of application

SETTINGS AND WORKING INSTRUCTIONS 19

Settings

Working instructions

Cross cut 90° and turntable 0°

Cross cut 90° and turntable 0° - 45°

Mitre cut 0°- 45°

Mitre cut 0°- 45° and turntable 0°- 45°

19

19

20

21

21

22

Saw blade replacement

Adjusting the laser

Maintenance

Electrical connection

AC motor

Storage

23

24

24

25

25

25

12

13

14

15

15

15

17

18

7

9

5

5

DISPOSAL AND RECYCLING

WARRANTY STATEMENT

Conditions

Terms

EC DECLARATION OF CONFORMITY

26

28

28

29

31

JCB-MS-210C

Instruction & User Manual

GENERAL SAFETY

INSTRUCTIONS

WARNING!

Read all safety warnings instructions, illustrations and specifications provided with this power tool.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. The term "power tool" in the warnings refers to your mainsoperated (corded) power tool or batteryoperated (cordless) power tool.

Save all warnings and instructions for future reference.

1 Work area safety a Keep work area clean and well lit b c

– Cluttered and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.

– Power tools create sparks which may ignite the dust or fumes.

Keep children and bystanders away while operating a power tool.

– Distractions can cause you to lose control.

2 a

Electrical safety

Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use any adapter plugs with earthed

(grounded) power tools

– Unmodified plugs and matching outlets will reduce risk of electric shock.

b c d

Avoid body contact with earthed or grounded surfaces such as pipes, radiators,ranges and refrigerators.

– There is an increased risk of electric shock if your body is earthed or grounded.

Do not expose power tools to rain or wet conditions.

– Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

e f

– Damaged or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

– Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a residual current device(RCD) protected supply

– Use of an RCD reduces the risk of electric shock.

3 Personal safety a b

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.

– A moment of inattention while operating power tools may result in serious personal injury.

Use safety equipment. Always wear eye protection.

– Safety equipment such as dust mask, non-skid safety shoes, hard hat, or

JCB-MS-210C

Instruction & User Manual

5

6 f c d e g h

– hearing protection used for appropriate conditions will reduce personal injuries.

Prevent unintentional starting.

Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.

– Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on.

– A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.

– This enables better control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.

– Loose clothes, jewellery or long hair can be caught in moving parts.

If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.

– Use of these devices can reduce dust related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.

– A careless action can cause severe injury within a fraction of a second.

f

4 a b c d e g

Power tool use and care

Do not force the power tool. Use the correct power tool for your application.

– The correct power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off.

– Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools.

– Such preventive safety measures reduce the risk of starting the power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

– Power tools are dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use.

– Many accidents are caused by poorly maintained power tools.

Keep cutting tools sharp and clean.

– Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc., in accordance with

JCB-MS-210C

Instruction & User Manual

h

5 a these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to

– be performed.

Use of the power tool for operations different from intended could result in a hazardous situation.

Keep handles and grasping surfaces dry,

– clean and free from oil and grease.

Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

–

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR MITRE SAWS

1 Mitre saws are intended to cut wood or wood-like products, they cannot be used

2

– with abrasive cut-off wheels for cutting ferrous material such as bars, rods, studs, etc.

Abrasive dust causes moving parts such as the lower guard to jam. Sparks from abrasive cutting will burn the lower guard, the kerf insert and other plastic parts.

Use clamps to support the workpiece

– whenever possible. If supporting the workpiece by hand, you must always keep your hand at least 100 mm from either side of the saw blade. Do not use this saw to cut pieces that are too small to be securely clamped or held by hand.

If your hand is placed too close to the saw blade, there is an increased risk of injury

3

4

5

6

7

– from blade contact.

The workpiece must be stationary and clamped or held against both the fence and the table. Do not feed the workpiece into the blade or cut “freehand” in any way.

Unrestrained or moving workpieces could be thrown at high speeds, causing injury.

Push the saw through the workpiece. Do not pull the saw through the workpiece.

To make a cut, raise the saw head and pull it out over the workpiece without cutting, start the motor, press the saw head down and push the saw through the workpiece.

– Cutting on the pull stroke is likely to cause the saw blade to climb on top of the workpiece and violently throw the blade assembly towards the operator.

Never cross your hand over the intended line of cutting either in front or behind the saw blade.

– Supporting the workpiece“cross handed” i.e. holding the workpiece to the right of the saw blade with your left hand or vice versa is very dang erous.

Do not reach behind the fence with either hand closer than 100 mm from either side of the saw blade, to remove wood scraps, or for any other reason while the blade is spinning.

– The proximity of the spinning saw blade to your hand may not be obvious and you may be seriously injured.

Inspect your workpiece before cutting. If the workpiece is bowed or warped, clamp it with the outside bowed face toward the fence. Always make certain that there is no gap between the workpiece, fence and

– table along the line of the cut

Bent or warped workpieces can twist or shift and may cause binding on the spinning saw blade while cutting. There

JCB-MS-210C

Instruction & User Manual

7

8

8 should be no nails or foreign objects in the workpiece.

Do not use the saw until the table is clear of all tools, wood scraps,

– etc., except for the workpiece.

Small debris or loose pieces of wood or other objects that contact the revolving blade can be thrown with high speed.

9

–

Cut only one workpiece at a time.

10

11

Stacked multiple workpieces cannot be adequately clamped or braced and may bind on the blade or shift during cutting.

Ensure the mitre saw is mounted or placed on a level, firm work

– surface before use.

A level and firm work surface reduces the risk of the mitre saw becoming unstable.

Plan your work. Every time you change the bevel or mitre angle setting, make sure the adjustable fence is set correctly to support the workpiece and will not interfere with the blade or the guarding system.

12

– Without turning the tool “ON” and with no workpiece on the table, move the saw blade through a complete simulated cut to assure there will be no interference or danger of cutting the fence.

Provide adequate support such as table extensions, saw horses, etc.

– for a workpiece that is wider or longer than the table top.

Workpieces longer or wider than the mitre saw table can tip if not securely supported. If the cut-off piece or workpiece tips, it can lift the lower

13

14

15

16

17

18 guard or be thrown by the spinning blade.

Do not use another person as a substitute for a table extension or as additional support.

– Unstable support for the workpiece can cause the blade to bind or the workpiece to shift during the cutting operation pulling you and the helper into the spinning blade.

The cut-off piece must not be jammed or pressed by any means against the spinning saw blade.

– If confined, i.e. using length stops, the cut-off piece could get wedged against the blade and thrown violently.

Always use a clamp or a fixture designed to properly support round material such as rods or tubing.

– Rods have a tendency to roll while being cut, causing the blade to “bite” and pull the work with your hand into the blade.

Let the blade reach full speed before contacting the workpiece.

– This will reduce the risk of the workpiece being thrown.

If the workpiece or blade becomes jammed, turn the mitre saw off. Wait for all moving parts to stop and disconnect the plug from the power source and/or remove the battery pack. Then work to free the jammed material.

– Continued sawing with a jammed workpiece could cause loss of control or damage to the mitre saw.

After finishing the cut, release the switch, hold the saw head down and wait for the blade to stop before

JCB-MS-210C

Instruction & User Manual

19

removing the cut-off piece.

– Reaching with your hand near the coasting blade is dangerous.

Hold the handle firmly when making an incomplete cut or when releasing the switch before the saw head is

– completely in the down position.

The braking action of the saw may cause the saw head to be suddenly pulled downward, causing a risk of injury.

WARNING!

This electric tool generates an electromagnetic field during operation. This field can impair active or passive medical implants under certain conditions. In order to prevent the risk of serious or deadly injuries, we recommend that persons with medical implants consult with their physician and the manufacturer of the medical implant prior to operating the electric tool.

Safety instructions for the handling of saw blades

1

2

3

4

5

6

7

8

9

10

11

12

Only use insertion tools if you have mastered their use.

Observe the maximum speed. The maximum speed specified on the insertion tool may not be exceeded. If specified, observe the speed range.

Observe the motor / saw blade direction of rotation.

Do not use any insertion tools with cracks.

Sort out cracked insertion tools. Repairs are not permitted.

Clean grease, oil and water off of the clamping surfaces.

Do not use any loose reducing rings or bushes for the reducing of holes on saw blades.

Make sure that fixed reducer rings for securing the insertion tool have the same diameter and have at least 1/3 of the cutting diameter.

Make sure that fixed reducer rings are parallel to each other.

Handle insertion tool with caution. They are ideally stored in the originally package or special containers. Wear protective gloves in order to improve grip and to further reduce the risk of injury.

Prior to the use of insertion tools, make sure that all protective devices are properly fastened.

Prior to use, make sure that the insertion tool meets the technical requirements of this electric tool and is properly fastened.

Only use the supplied saw blade for cutting wood, never for the processing of metals.

JCB-MS-210C

Instruction & User Manual

9

10

Attention: Laser radiation

Do not stare into the beam

Class 2 laser

Protect yourself and your environment from accidents using suitable precautionary measures!

Do not look directly into the laser beam with unprotected eyes.

Never look into the path of the beam.

Never point the laser beam towards reflecting surfaces and persons or animals.

Even a laser beam with a low output can cause damage to the eyes.

Caution - methods other than those specified here can result in dangerous radiation exposure.

Never open the laser module. Unexpected exposure to the beam can occur.

If the mitre saw is not used for an extended period of time, the batteries should be removed.

The laser may not be replaced with a different type of laser.

Repairs of the laser may only be carried out by the laser manufacturer or an authorised representative .

JCB-MS-210C

Instruction & User Manual

JCB-MS-210C

Instruction & User Manual

16a. Extension block

16b. Stop rail set crew

Fasten bolt for turn table

11

JCB-MS-210C

Instruction & User Manual

14

VIBRATION AND NOISE INFORMATION

Total noise values determined in accordance with EN62841

A-Weighted Sound Pressure (L pA

)

Uncertainty K pA

A-Weighted Sound Level (L wA

)

9 1 , 8

3 dB

dB(A)

108,26 dB(A)

Uncertainty K wA

3 dB

Wear ear protection when sound pressure is over 80 dB(A)

WARNING!

Wear hearing protection.

The effects of noise can cause a loss of hearing. The above-mentioned noise emission values were measured in accordance with a standardised test procedure and can be used to compare one power tool with another.

The above-mentioned noise emission values can also be used for the preliminary assessment of exposure.

Warning:

The noise emissions during the actual use of the power tool may differ from the above-mentioned values depending on the power tool being used, in particular on the type of workpiece being processed.

Try to keep emissions as low as possible, for example by limiting your working time. In this regard, all the operational cycle phases must be taken into consideration (such as the times when the tool is switched off or running idle).

JCB-MS-210C

Instruction & User Manual

OPERATING INSTRUCTIONS

Intended Use

The mitre saw is used for the cutting of wood and plastic, according to the machine capacity.

Warning!

The supplied saw blade is only intended for the sawing of wood! Do not use this blade for the sawing of plastic!

The saw is not suitable for the cutting of firewood.

The machine may only be used in the intended manner.

Only suitable saw blades may be used for the machine. The use of any type of cutting wheels is prohibited.

An element of the intended use is also the observance of the safety instructions, as well as the assembly instructions and operating information in the operating manual.

Persons who operate and maintain the machine must be familiar with the manual and must be informed about potential dangers.

Any use beyond this is improper. The user/ operator, not the manufacturer, is responsible for damages or injuries of any type resulting from this.

In addition, the applicable accident prevention regulations must be strictly observed.

Other general occupational health and safetyrelated rules and regulations must be observed.

The liability of the manufacturer and resulting damages are excluded in the event of modifications of the machine.

Despite use as intended, specific risk factors cannot be entirely eliminated. Due to the design and layout of the machine, the following risks remain:

•

•

•

•

•

•

• Contact with the saw blade in the noncovered saw area.

Reaching into the running saw blade (cutting injury).

Kick-back of workpieces and workpiece parts.

Saw blade breakage.

Ejection of faulty carbide parts of the saw blade.

Hearing damage when the necessary hearing protection is not used.

Harmful emissions of wood dusts during use in enclosed areas.

Please observe that our equipment was not designed with the intention of use for commercial or industrial purposes. We assume no guarantee if the equipment is used in commercial or industrial applications, or for equivalent work.

Commissioning

Prior to commissioning, observe the safety instructions in the operating instructions.

REMOVAL FROM THE PACKAGING

Remove the machine from its package, which protects it during transport, without damaging the package in order to be able to use it later for transporting the mitre saw for long-term storage.

JCB-MS-210C

Instruction & User Manual

1 5

1

1

JCB-MS-210C

Instruction & User Manual

Fig.1.1

10

15

14

Fig.1.2

19

Fig.1.3

16a

16b

JCB-MS-210C

Instruction & User Manual

27

19

Assembly

WARNING!

For your own safety, only insert the mains plug in an outlet when all assembly steps have been completed and you have read and understood the safety and operating instructions.

Lift the saw out of the packaging and place it on your work bench. (Positioning of the saw on the work bench - see the next page under „POSITIONING / WORK STATION“)

Assembling the work piece clamping device (fig. 1.1)

• Loosen the locking knob (17) and attach the work piece clamping device (10) to the left or right of the fixed saw bench.

• r (17).

Assembling the work piece supports

(fig. 1.1 – 1.2)

•

• Loosen the fix screw (14) and guide the workpiece support through the specified hole on the side of the fixed saw bench.

Make sure that the work piece support (15) is also guided through the two plates (19) on the underneath.

• Afterwards, retighten the fix screw (14).

• Repeat this process on the other side.

Assembling the support stand (fig. 1.1 – 1.2)

•

• Loosen the fix screw (14) on the underneath of the saw through the specified holes on the back of the saw.

Afterwards, retighten the fix screw (14).

17

18

•

Installation of the dust bag

Squeeze together the metal ring on the dust bag (12) and attach it to the outlet opening in the motor area.

•

•

•

Emptying the dust bag

By pressing the metal ring wings of the dust bag (12) together the dust bag can be disengaged from the outlet opening.

Open the zipper of the dust bag and shake the contents into a dustbin.

Close the zipper and install the dust bag on the machine again as described.

Area of application

•

•

Intended application possibilities

The machine cuts:

Wood and materials similar to wood

Plastic

Unintended application possibilities

The machine is not suitable for:

•

•

• Ferritic materials, steel and cast iron, as well as other material types which are not listed, particularly food.

Mitre saw without guard.

Materials larger than the specified cutting data:

90°/90° /

90°/45°

45°/90°

45°/45°

120 x 60 mm

80 x 60 mm

120 x 33 mm

80 x 33 mm

JCB-MS-210C

Instruction & User Manual

SETTINGS AND WORKING INSTRUCTIONS

Fig. 2

2

Settings

CROSS-CUTTING

ATTENTION: Before carrying out the following adjustments, please check whether the motor of the machine is switched off.

Fig. 3

21

25

17

24

Pivoting the table plate (Fig. 2)

The mitre saw can be pivoted left and right with the rotary table. Exact angle adjustment is possible on the basis of the scale. The angle can be precisely and quickly adjusted from 0° to 45° with locking positions at 15°, 22.5° and 30°.

To pivot the rotary table, loosen the set screw

(21) and rotate the unit using the handle (1) until the desired angle is reached. Then secure it with the set screw (21).

Tilt of the saw unit (Fig. 3)

The saw unit can be tilted at an angle of up to 45°.

Loosen the locking knob (17) on the rear side of the machine and tilt the unit to the desired angle position according to the scale. The angle can be set on the basis of the scale (24) using the pointer (25). Then the handle must be retightened.

Working instructions

After you have carried out all the tasks described above, you can begin working.

ATTENTION: Always keep your hands away from the cutting zone and never attempt to reach in while cutting.

FIXING A WORKPIECE

Clamp the work piece on the work table with the workpiece clamp (10 - Fig 1) in order to fix it in place.

JCB-MS-210C

Instruction & User Manual

19

20

Fig. 4

2

3

16

1

26

•

•

Cross cut 90° and turntable 0° (Fig. 4,

1.3)

Attention! For 90° mitre cuts, the extention block (16a) must be fixed in the inner position.

•

•

•

• Open the set screw (16b) on the extention block (16a) with an Allen key and push the extention block (16a) inwards.

The moveable extention block (16a) must be locked in a position far enough from the inner position that the distance between the extention block (16a) and the saw blade (5) is no more than 8 mm.

Before making the cut, check that no collision could occur between the extention block (16a) and the saw blade (5).

Secure the set screw (16b) again.

Loosen the locking knob (17).

Lift the saw unit by the handle (1) until it locks in place in the top position.

•

•

•

•

• Lock the material with the clamping device

(10) on the fixed saw table to prevent the material from moving during the cutting operation.

Press the workpiece evenly on the stop rail (16); make sure that you hand remains outside the cutting area of the saw blade.

With your right hand on the handle (1), press the release button (3) so that the unit can also be pivoted downward.

The motor starts when the ON/OFF switch

(1) is pressed.

Slowly bring the saw blade down to the workpiece and cut through it with moderate pressure.

JCB-MS-210C

Instruction & User Manual

• When the cutting operation is completed, move the machine head back to its upper

(home) position and release the ON/OFF button (2).

Attention! The machine executes an upward stroke automatically due to the return spring, i.e. do not release the handle (1) after completing the cut; instead allow the machine head to move upwards slowly whilst applying light counter pressure.

Cross cut 90° and turntable 0° - 45° (Fig.

4, 2, 1.3)

The crosscut saw can be used to make crosscuts of 0°-45° to the left and 0° -45° to the right in relation to the stop rail.

Attention! For bevel cuts (inclined saw head), the moveable extention block (16a) must be fixed in the inner position.

• Open the set screw (16b) on the moveable extention block (16a) and push the moveable stop rail extention block (16a) outwards.

• The moveable extention block (16a) must be locked in a position far enough from the inner position that the distance between the extention block (16a) and the saw blade (5) is no more than 8 mm.

•

•

•

•

• Before making the cut, check that no collision could occur between the extention block (16a) and the saw blade (5).

Tighten the set screw (16b) again.

Loosen set screw (21).

Use the handle (1) to set the turntable (9) to the desired angle. The pointer on the turntable must coincide with the desired angular extent of the scale on the base (7).

Re-tighten the set screw (21) to fix the turntable (9).

• Cut as described under section „Cross cut

90° and turntable 0°“.

•

•

Mitre cut 0°- 45° (Fig. 1, 1.3)

The crosscut saw can be used to make mitre cuts of 0° - 45° in relation to the work face.

Important. To make miter cuts (inclined saw head), the adjustable extention block (16a) must be fixed at the outer position.

•

• Open the set screw (16b) for the adjustable extention block (16a) with an Allen key and push the adjustable stop rail outwards.

The adjustable extention block (16a) must be fixed far enough in front of the innermost position that the distance between the extention block (16a) and the saw blade (5) amounts to a maximum of 8 mm.

•

• Before making a cut, check that the extention block (16a) and the saw blade (5) cannot collide.

Secure the set screw (16b) again.

Move the machine head to the top position.

Fix the turn table (9) in the 0° position.

•

•

• Loosen the fix screw (23) and use the handle (2) to angle the machine head to the left, until the bevel pointer (25) indicates the desired angle measurement on the scale

(24).

Re-tighten the fixing screw (23).

Cut as described under section „Cross cut

90° and turntable 0°“.

JCB-MS-210C

Instruction & User Manual

21

22

Mitre cut 0°- 45° and turntable 0°- 45°

(Fig. 1, 2, 1.3)

The crosscut saw can be used to make mitre cuts to the left of 0°- 45° in relation to the work face and, at the same time, 0° - 45° to the left or 0° - 45° to the right in relation to the stop rail (double mitre cut).

•

•

Important. To make miter cuts (inclined saw head), the adjustable extention block (16a) must be fixed at the outer position.

• Open the set screw (16b) for the adjustable extention block (16a) and push the adjustable extention block (16a) outwards.

•

• The adjustable extention block (16a) must be fixed far enough in front of the innermost position that the distance between the extention block (16a) and the saw blade (5) amounts to a maximum of 8 mm.

Before making a cut, check that the extention block (16a) and the saw blade (5) cannot collide.

Secure the set screw (16b) again.

Move the machine head to its upper position.

•

• Release the turn table (9) by loosening the set screw (21).

Using the handle (2), set the turn table (9) to the desired angle (refer also to point “Cross cut 90° and turntable 0° - 45°” in this regard).

•

•

•

•

• Re-tighten the set screw (21) in order to secure the rotary table.

Undo the locking konb (17)

Use the handle (2) to tilt the machine head to the left until it coincides with the required angle value (in this connection see also section “Mitre cut 0°- 45°”).

Re-tighten the locking konb (17).

Cut as described under section “Cross cut

90° and turntable 0°”.

JCB-MS-210C

Instruction & User Manual

Fig. 5

29

28

30

6

Saw blade replacement (Fig. 5)

• Pull out the mains plug.

• Place the saw unit in „cross-cutting“ position

• Unlock the moving saw blade guard (6) by pressing the release button (3 - Fig. 1); in the process, raise the saw blade guard so that the saw blade is free.

• Actuate the spindle lock (30 - Fig. 5).

• Loosen the saw blade flange bolt

•

- ( Attention: left-handed thread ).

R emove the out flange bolt

(28).

(28) and saw blade

• Carefully remove the saw blade (risk of injury from the saw blade teeth).

• Place a new saw blade on the inner saw rotational direction of the saw blade.

• tighten the screw.

• Move the saw blade guard back to the correct position.

JCB-MS-210C

Instruction & User Manual

23

24

Fig. 6

31

32

Adjusting the laser (Fig. 6)

If the laser (31) ceases to indicate the correct cutting line, you can readjust the laser. To do so, open the laser switch (32) and set the laser by moving sideways to that the laser beam strikes the teeth of the saw blade (5).

Maintenance

If personnel qualified for unusual maintenance tasks or repairs must be obtained during of after the warranty period, please always contact a service point recommended by us or contact the manufacturer.

•

• Only perform repair, maintenance and cleaning work as well as the correction of malfunctions with the drive switched off as a basic rule.

All protective and safety equipment must be reassembled immediately after repair, maintenance is completed.

NORMAL SERVICE TASKS

Normal service tasks can also be performed by untrained personnel and are all described in the preceding sections and in this chapter.

• The mitre saw must not be lubricated, because it always cuts dry surfaces; all moving machine parts are self-lubricating.

•

• In the event of service work, personal protective equipment must always be work

(protective goggles and gloves).

Remove saw dust and chips regularly by cleaning the cutting zone and support surfaces.

We recommend using a suction tool or brush.

ATTENTION: Do not use compressed air!

Check the saw blade from time to time: If problems arise with the blade, it must be ground by a specialist or replaced, depending on the condition.

JCB-MS-210C

Instruction & User Manual

DECOMMISSIONING OF THE MACHINE

After the machine is decommissioned it can be disposed of with normal industrial waste.

Service information

Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

Wear parts*: Carbon brush, saw blade, table inserts, dust bags, batteries,

* Not necessarily included in the scope of delivery!

Electrical connection

The electrical motor installed is connected and ready for operation. The connection complies with the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the extension cable used must also comply with these regulations.

Important information

In the event of an overloading the motor will switch itself off. After a cool-down period (time varies) the motor can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often damaged.

This may have the following causes:

•

•

•

• Passage points, where connection cables are passed through windows or doors.

Kinks where the connection cable has been improperly fastened or routed.

Places where the connection cables have been cut due to being driven over.

Insulation damage due to being ripped out of the wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not be used and are life-threatening due to the insulation damage.

Check the electrical connection cables for damage regularly. Make sure that the connection cable does not hang on the power network during the inspection.

Electrical connection cables must comply with the applicable VDE and DIN provisions. Only use connection cables with the marking „H 07

RN“.

The printing of the type designation on the connection cable is mandatory.

•

•

AC motor

The mains voltage must be 230 V~

Extension cables up to 25 m long must have a cross-section of 1.5 mm2.

•

•

Connections and repairs of electrical equipmentm may only be carried out by an electrician.

Please provide the following information in the event of any enquiries:

•

Type of current for the motor

Machine data - type plate

Machine data - type plate

Storage

Store the machine and its accessories in a dark, dry and frost-free place, inaccessible to children. The ideal storage temperature is between 5 and 30˚C.

Store the power tool in its original packaging.

Cover the power tool to protect it from dust and humidity.

Keep the operating manual with the power tool.

JCB-MS-210C

Instruction & User Manual

25

26

DISPOSAL AND RECYCLING

Disposing of transport packaging

The packaging protects the machine from damage during transport. The packaging material is usually chosen for factors of environmental friendliness and disposal. It can therefore be recycled. Returning the packaging to the material life cycle saves raw material and reduces waste.

Packaging parts (e.g. plastic sheets, Styropor®) can be dangerous for children. Risk of choking!

Store packaging parts beyond the reach of children and dispose of them as soon as possible

Old devices must not be disposed of with household waste!

This symbol indicates that this product must not be disposed of together with domestic waste in compliance with the

Directive (2012/19/EU) pertaining to waste electrical and electronic equipment

(WEEE). This product must be disposed of at a designated collection point. This can occur, for example, by handing it in at an authorised collecting point for the recycling of waste electrical and electronic equipment. Improper handling of waste equipment may have negative consequences for the environment and human health due to potentially hazardous substances that are often contained in electrical and electronic equipment. By properly disposing of this product, you are also contributing to the effective use of natural resources. You can obtain information on collection points for waste equipment from your municipal administration, public waste disposal authority, an authorised body for the disposal of waste electrical and electronic equipment or your waste disposal company.

JCB-MS-210C

Instruction & User Manual

JCB Tools Warranty Terms and Conditions

JCB Power Tools are guaranteed against manufacturing defects for

2 years from date of purchase by simply registering your product online within 30 days. Proof of purchase required. This does not affect your statutory rights.

To register your JCB Power Tool, please visit: jcb-tools.com

Online registration is required to receive a warranty certificate to activate your standard 2 year warranty. Registration is only available online via www.jcb-tools.com. You will need your original sales receipt, the model number and the serial number (if applicable) of your product.

Kits comprising of two or more tools are excluded from single registration and must registered individually for full warranty cover.

Upon successful registration, a warranty certificate will be available to download, print or save as a PDF document. The relevant warranty certificate together with the original sales receipt will be required in the event of any claim within the warranty period.

Should you choose not to register your product within 30 days of purchase, your statutory consumer rights will not be affected. You will need the original sales receipt as proof of purchase in the event of a warranty claim.

Warranty cover commences from the date of purchase on the retail sales receipt and is valid only for JCB Tools products purchased within the UK bearing the CE mark and a visible serial number.

In the unlikely event your JCB Power Tool is subject to a manufacturing fault within the warranty period, JCB Tools may repair the product by replacing defective parts free of charge at our discretion. In the event parts are irreplaceable JCB Tools may replace your product free of charge. The original product will remain the property of JCB Tools in this situation.

•

•

•

•

The above repair or replacement of products will be undertaken providing that:

• The product has been subject to fair wear and tear only.

The product has not been subject to accidental or cosmetic damage.

The product has not been misused and has been used only in accordance with the instruction manual provided.

The product has not been subject to overload or insufficient servicing and maintenance.

•

The product has not been subject to any abnormal environmental conditions or inappropriate operating conditions.

Repairs have not been attempted by an unauthorised person and no modifications have been made to the product.

• Repairs have not been undertaken using non-genuine spare parts.

JCB-MS-210C

Instruction & User Manual

27

2 8

JCB Power Tools used for Hire Fleets or as part of B2B and Service Contracts are not covered by these terms and conditions.

•

•

JCB Tools standard 2 Year warranty excludes the following (where relevant);

• Components normally subject to wear such as carbon brushes.

Batteries, Chucks and Chargers.

Accessories and consumable items.

• Cases and tool storage products.

If your product develops a fault within 30 days of purchase, return it to the retailer where it was purchased together with your sales receipt. If a product develops a fault after 30 days a warranty claim must be submitted.

If you have a warranty claim please take your product, original sales receipt and if applicable, a copy of your extended warranty certificate to your local JCB Tools dealer.

If you wish to send your product to us directly, please call us on 03308380257 to arrange warranty claim or repair. Delivery and repair charges may apply at our discretion should the warranty claim be invalid for any of the reasons illustrated above. In the event charges are not accepted the product will be retained by JCB Tools and remain the property of JCB Tools.

The information on both your sales receipt and your extended warranty certificate must match.

JCB TOOLS WILL NOT BE LIABLE FOR ANY INJURIES OR CONSEQUENTIAL DAMAGES

RESULTING FROM USE OF THIS PRODUCT.

JCB-MS-210C

Instruction & User Manual

EC DECLARATION OF CONFORMITY

Original Declaration of Conformity

We,

JCB Tools

Declare that the product:

Description: Mitre Saw

Type: JCB-MS-210C

Function: Split cuts in wood and plastic.

Complies with the following Directives;

EC Machinery Directive 2006/42/EC

EC Electromagnetic Compatibility Directive 2014/30/EU

RoHS Directive 2011/65/EU*

Standards conform to

EN62841-1:2015

EN62841-3-9:2015+A11

EN55014-1:2006+A1+A2

EN55014-1:20 1 7

EN55014-2:2015

EN61000-3-2:2014

EN61000-3-3:2013

This declaration of conformity is issued under the sole responsibility of the manufacturer.

* The object of the declaration described above fulfils the regulations of the directive 2011/65/EU of the European Parliament and Council from 8th June

2011, on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

The person authorized to compile the technical file:

Date: 04/01/2019

Signature:

Name/ title: Mya Yee Lwin / Quality Assurance Manager

Address: JCB Tools, 55 Romsey Industrial Estate,Romsey,

SO51 0HR,UK. (REG: 11062222)

Company Registration Number: 1062222

JCB-MS-210C

Instruction & User Manual

29