Audio Technica UniPoint AT831b Quick Start Manual
Audio Technica UniPoint AT831b is a miniature condenser microphone with a cardioid polar pattern, designed for hands-free applications in sound reinforcement systems, and for use by professional musicians, especially for pickup of acoustic guitar. It provides improved gain before feedback that normally cannot be achieved with miniature omnidirectional microphones. Close-up voice and instrument pickup are crisp and clean, yet full sounding, while suppression of background noise is significantly improved over that of stand-mounted full-size cardioid microphones.
Advertisement
Advertisement
AT831b
MINIATURE
CARDIOID
CONDENSER
MICROPHONE
Description
The AT831b is a miniature condenser microphone with a cardioid polar pattern. It has been designed for hands-free applications in sound reinforcement systems, and for use by professional musicians, especially for pickup of acoustic guitar. The
AT831b provides improved gain before feedback that normally cannot be achieved with miniature omnidirectional microphones.
Close-up voice and instrument pickup are crisp and clean, yet full sounding, while suppression of background noise is significantly improved over that of standmounted full-size cardioid microphones.
Audio -Technica design engineers have utilized the newest low-mass technology in the quest for superior performance. The permanent charge is now on the fixed back plate, rather than the moving element. With
A-T fixed charge “back plate“ construction, a gold-vaporized diaphragm just 2 microns thick (about 0.000079") can be used. This reduces moving mass, thus improving frequency response and transient response while reducing distortion.
The AT831b can be powered from an external
9V to 52V DC phantom supply or from an AA/UM3 1.5V battery (supplied). Current demands are so low that an alkaline battery will provide about 1200 hours of continuous use.
The microphone element is enclosed in a rugged housing with low-reflectance finish.
Internal construction is designed to minimize handling and clothing noise. A 6' (1.8 m) cable is provided between the microphone and power module. A built-in 3-position switch on the power module allows selection of off, on/flat response, or on/low-roll-off. An
AT8417 clothing clip and AT8444 guitar adapter are provided, as well as an accessory AT8116 windscreen. The microphone is well protected by a speciallydesigned carrying case.
Operation and Maintenance
To install the battery, remove the cap from the top of the power module. Insert the battery, being certain to observe battery polarity as marked (+ end toward the cap release button). For longest battery life, the switch should remain off except when the microphone is in use. While standard carbonzinc AA batteries will operate the microphone satisfactorily, alkaline or mercury cells are preferred for longer service life. Only
“leakproof” batteries should be used. The battery does not have to be in place to use in phantom power mode. Phantom power requires 9V to 52V DC.
The microphone may be worn on the person or attached to a musical instrument. If used with an instrument, it may be attached by means of the clothing clip or the special instrument adapter provided. The power module may be worn on the belt, utilizing the belt clip, or located in any convenient place.
An open-pore foam windscreen simply slips over the head of the microphone, effectively reducing wind noise or “popping” when used extra close.
Output is low impedance balanced. The
XLRM-type output connector mates with
XLRF-type cable connectors. The balanced signal appears across Pins 2 and 3, while the ground (shield) connection is Pin 1. Output is phased so that positive acoustic pressure produces positive voltage at Pin 2 in accordance with industry convention.
While a modern condenser microphone is not unduly sensitive to the environment, temperature extremes can be harmful. Exposure to high temperatures can result in gradual and permanent reduction of the output level.
Avoid leaving the microphone in the open sun or in areas where temperatures exceed 110° F
(43° C) for long periods of time. Extremely high humidity should also be avoided.
Architects and Engineers Specifications
The microphone shall be a fixed-charge condenser with a cardioid polar pattern and a frequency response of 40 Hz to 20,000 Hz. It shall operate from an external 9V to 52V DC phantom power source or, alternatively, from a 1.5V AA / UM3 battery. Nominal opencircuit output voltage shall be 6.3 mV (phantom) or 5.6 mV (battery) at 1 kHz, 1 Pascal.
Output with the included power module shall be low impedance balanced (200 ohms-phantom, 270 ohms-battery).
The microphone shall have a permanentlyattached 6' (1.8 m) miniature cable between the microphone and power module. The power module shall house the battery and contain an off/on/low-roll-off switch. The power module shall terminate in a 3-pin
XLRM-type connector.
The microphone shall be mountable in an included instrument adapter or clothing clip.
The microphone shall be 0.98" (25.0 mm) long with a diameter of 0.39" (10.0 mm). The microphone weight shall be 0.1 oz (2.8
grams). Finish shall be low-reflectance black.
The Audio-Technica AT831b is specified.
Frequency Response
50
LEGEND
100 200 500 1k
Frequency in Hertz
2k
12" or more on axis
Roll-off
5k 10k 20k
10 dB
AT831b
270
300
330
Polar Pattern
0
30
60
240
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
210 150
180
SCALE IS 5 DECIBELS PER DIVISION
120
XLRM-Type Plug Wiring
Low Impedance Balanced
1 /
4
" Phone Plug Wiring
Low Impedance Unbalanced
RED WIRE WHITE WIRE
TIP SLEEVE SHIELD
90
AT8530 Power Module Dimensions
0.87"
22.0 mm
2.48"
63.0 mm
Push Button
To Release Cap
POWER MODULE audio-technica
MADE IN JAPAN
3.27"
83.0 mm
SWITCH
Roll-off
Flat
Off
OFF
PUSH
AT831b
SPECIFICATIONS
†
ELEMENT
POLAR PATTERN
FREQUENCY RESPONSE
LOW-FREQUENCY ROLL-OFF
OPEN CIRCUIT SENSITIVITY
IMPEDANCE
PHANTOM
BATTERY
PHANTOM
BATTERY
MAXIMUM INPUT SOUND LEVEL PHANTOM
BATTERY
DYNAMIC RANGE (TYPICAL) PHANTOM
BATTERY
SIGNAL-TO-NOISE RATIO
1
SWITCH
BATTERY TYPE
BATTERY CURRENT
BATTERY LIFE
PHANTOM POWER REQUIREMENTS
WEIGHT (LESS CABLE AND ACCESSORIES)
MICROPHONE
POWER MODULE
DIMENSIONS
MICROPHONE
POWER MODULE
OUTPUT CONNECTOR (POWER MODULE)
CABLE
ACCESSORIES FURNISHED
Fixed-charge back plate permanently polarized condenser
Cardioid (Unidirectional)
40 -20,000 Hz
80 Hz, 18 dB/octave
–44 dB (6.3 mV) re 1V at 1 Pa*
–45 dB (5.6 mV) re 1V at 1 Pa*
200 ohms
270 ohms
135 dB SPL, 1 kHz at 1% T.H.D.
121 dB SPL, 1 kHz at 1% T.H.D.
106 dB, 1 kHz at Max SPL
92 dB, 1 kHz at Max SPL
65 dB, 1 kHz at 1 Pa*
Off, on-flat, on-roll-off
Use only “leakproof” AA/UM3 1.5V battery
0.4 mA typical
1200 hours (alkaline battery)
9-52V DC, 2 mA typical
0.1 oz (2.8 grams)
5.2 oz (147 grams)
0.98" (25.0 mm) long, 0.39" (10.0 mm) dia.
3.27" (83.0 mm) H x 2.48" (63.0 mm) W x
0.87" (22.0 mm) D, not including clip
Integral 3-pin XLRM-type
Integral 6' (1.8 m), permanently attached between microphone and power module
AT8417 clothing clip; AT8444 instrument adapter;
AT8530 power module; AT8116 windscreen; battery; protective carrying case
† In the interest of standards development, A.T.U.S. offers full details on its test methods to other industry professionals on request.
* 1 Pascal = 10 dynes/cm 2 = 10 microbars = 94 dB SPL
1 Typical, A-weighted, using Audio Precision System One.
Dimensions
0.39"
10.0 mm
0.98"
25.0 mm
Optional Accessories:
• CP8201 line matching transformer
(Lo-Z to 50,000 ohms).
• AT8202 adjustable in-line attenuator for use with balanced Lo-Z microphones.
• AT8314 2-conductor, shielded, vinyl-jacketed, broadcast-type cable with XLRF-type connector at microphone end, XLRM-type connector at equipment end. Available in
10', 20', 25', 30', 50' & 100' lengths.
• AT8412 double clothing clip.
• AT8414 tie tac.
• AT8438 stand adapter.
• CP8506 four-channel 48V phantom power supply (AC powered).
• AT8801 single-channel 48V phantom power supply (AC powered).
One-Year Limited Warranty
Audio-Technica microphones and accessories purchased in the U.S.A. are warranted for one year from date of purchase by
Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to
A.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase date.
Prior approval from A.T.U.S. is required for return. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or modification.
For return approval and shipping information, contact the Service Department, Audio -Technica U.S., Inc.,
1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law, A.T.U.S. will have no liability for any consequential, incidental, or special damages; any warranty of merchantability or fitness for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
Form No. 0310-0764-07-B/W © 1998 Audio-Technica U.S., Inc. Printed in U.S.A.

Public link updated
The public link to your chat has been updated.
Advertisement