Eneo VMC-19LEDMD User Manual
The Eneo VMC-19LEDMD is a professional 19-inch LCD monitor with a resolution of 1280 x 1024 pixels, a 12V power supply, and protection glass. It features HDMI connectivity, a desktop design, and a user-friendly OSD menu for adjusting picture and sound settings. With its sleek and stylish design, the Eneo VMC-19LEDMD is a great choice for both home and office use.
Advertisement
Advertisement
User Manual
Professional Monitor 19”
(48cm) LCD/TFT, 1280x1024,
12V, Protection Glass, HDMI,
Desktop
VMC-19LEDMD
EN
Installation and User's Guide
1. SAFETY INSTRUCTION
Follow this safety instruction to use the monitor properly and prevent the damage.
This safety instruction has “Warning” & “Caution” as below
Warning - If the user does not follow this instruction, it may cause the serious damage to the user.
Caution - If the user does not follow this instruction, it may cause the slight damage to the user or cause some damages to the monitor.
Keep this user’s guide book for later use.
Warning
Never remove the back cover and touch the inside of the monitor.
If you need a service, please contact the service center.
Keep away the monitor from the direct sunlight and a heating appliance.
Never put objects of any kind into this product as they may result in a risk of fire or electric shock.
Connect the power cord to the wall outlet tightly. If the power cord or plug are defective and the wall outlet is not tight, please do not use them.
2
Installation and User's Guide
Warning
Do not install this monitor on the outside and near water. It may cause damage to the product, electric shock and fire.
For cleaning do not use liquid cleaners.
Never touch the power plug with wet-hands.
When lightning and thundering, unplug the monitor from the wall outlet and never touch it.
Unplug this product from the wall outlet, when it does not operate for a long time.
When smoking and noising from the monitor, unplug the product from the wall outlet and contact a service center.
W A R N I I N G : :
How to fix
Do not open this product as it contains high voltage inside.
It may create an electric shock.
If the user disassembles and remove the back cover, it does not make sure to make up for the damage and do a service and exchange the monitor.
3
Installation and User's Guide
Cautions
Install this monitor some distance from the wall and do not install unless proper ventilation is provided.
Place this product on a stable place.
If not, it may fall, causing serious damages to the monitor and people.
The openings must not be blocked by curtain, rug or other similar surface.
When carrying this monitor, be careful not to damage the panel and drop it
It may cause some trouble.
Before carrying the monitor, turn it off and unplug the signal cables and the power cord from the wall outlet.
Take the power plug out from the wall outlet.
Do not pull the cable. It may snap the innerwires and cause overheating and fire.
4
Cautions
Install this monitor about 50cm far from the eyes and an angle of 0~15 degrees below eyes. Too close installation may cause having weak sight.
Installation and User's Guide
Do not press the LCD panel with hands or the sharpened material hardly.
For cleaning, unplug the monitor from the wall outlet. Do net use the liquid cloth.
Use the soft cloth.
Do not use the chemical liquid for cleaning.
It may cause fading and breakage.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR WATER.
Instructions for Disposal of Electrical and Electronic Equipment in Private
Households
Disposal of used Electrical and Electronic Equipment
(Applicable in the European Union and other European countries with garbage separate disposal and collection methods)
This symbol on the product, or in the related documents in the package, indicates that this
product shall not be treated as normal household waste. Instead, it should be taken to a proper
applicable collection point or depot for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent possible negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources.
For more detailed information about recycling of this product, please contact your local city authority, your household waste disposal service or the place where you purchased the product.
5
Installation and User's Guide
2. FCC RF INTERFERENCE STATEMENT
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio, TV technician for help.
● Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment.
DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of communications.
6
Installation and User's Guide
TABLE OF CONTENTS
ITEM No
1
1-1
2
1-2
3
3-1
4
3-2
4-1
4-2
4-3
4-4
5
6
4-5
4-6
SAFETY INSTRUCTION
Warning
Caution
FCC STATEMENT
INSTALLATION
Parts
How to Install
OSD Menu Setting
Menu Structure
PICTURE Menu
SOUND Menu
OPTION Menu
INPUT SOURCE
Audio Volume
FEATURES
TROUBLESHOOTING
Page
2
20
21
6
8
12
7
3. INSTALLATION
3-1 Parts
Installation and User's Guide
LCD Monitor
Adapter User Manual Power Cable
Battery Remote Controller
8
3-2 How to Install
KEY BUTTON
Installation and User's Guide
SHORT KEY FUNCTION
OSD Key
MENU / EXIT
SOURCE /
AUTO /
VOL
SELECT
LED
+
Function
Activate the menu function / Exit from the menu
Input source menu / Source selection(move down from OSD menu)
Auto-fit screen with PC-RGB input / move up from OSD menu
Decrease the level of volume and move the previous menu
Increase the level of volume and select the OSD menu
Power On / Off
Red : Power Off state
Green : Power On and available input signal state
Orange : When DPMS "ON" state, no input signal
Press “ , ” Key 10 seconds simultaneously to lock / unlock OSD Key
9
Installation and User's Guide
A
B
REMOTE CONTROLLER
A
MODE SELECT MENU
VIDEO1
Select VIDEO1 mode
HDMI1
Select HDMI1 mode
HDMI2
Select HDMI2 mode
POWER
VIDEO1
VGA
DVI
HDMI2
SCAN MODE
VIDEO2
AUTO
HDMI1
MUTE
S-VIDEO
COLOR TEMP
S.SET
PIP
VOL-
MENU/EXIT
P.INPUT
P.LOCATION
P.SIZE
P.SWAP
STILL
VOL+
KEY LOCK
B
OSD CONTROL MENU
POWER
Turn ON / OFF the monitor
AUTO
Auto adjust position of the screen (in VGA mode)
SCAN MODE
Select the scan mode of the screen
MENU / EXIT
Activate and exit the OSD menu
STILL
Freeze the current image
VIDEO2
Select VIDEO2 mode
VGA (RGB)
Select VGA mode
MUTE
Turn ON / OFF the sound
COLOR TEMPERATURE
Select color temperature of the screen
VOL- / VOL+
Increase / Decrease the volume level
KEY LOCK
Locking the button (Prevent operation)
11
Installation and User's Guide
CONNECTION
1 2 3 4 5
1 DC12V
DC adapter input
2 AUDIO (VIDEO-1)
Stereo audio input for VIDEO-1
3 AUDIO (VIDEO-2)
Stereo audio input for VIDEO-2
4 VIDEO-1 IN / OUT
VIDEO-1 signal input / looping out
5 VIDEO-2 IN / OUT
VIDEO-2 signal input / looping out
6 HDMI 1
HDMI signal 1 input
7 HDMI 2
HDMI signal 2 input
8 VGA
VGA (PC RGB) signal input
9 AUDIO (PC)
Stereo audio input for VGA
10 For FW Update
10
9
8
7
6
10
Installation and User's Guide
4. OSD MENU SETTING
4-1 Menu Structure
When user presses the menu key, the first “PICTURE” menu is displayed. Select by " ◀ " key then three types of menu functions are shown as below.
- PICTURE : Menu related to PICTURE Function
- SOUND : Menu related to SOUND Function
- OPTION : Other OSD Menu Status Control and Firmware Update
If press "▲, ▼" key, then select sub title in functions.
4-2 PICTURE Menu
Picture Mode
Color Temperature
Aspect Ratio
Noise Reduction
Screen
Color Range
Dymanic
Cool
16 : 9
Middle
0-255
PICTURE
PC-RGB:
The PICTURE Menu can be selected from the following 7 modes by pressing the ▲ or ▼ key.
Picture Mode Adjust sate of the picture
Color Temperature Change color according to the color temperature
Aspect Ratio
Noise Reduction
Screen
Color Range
Change the aspect ratio
Adjust noise attenuation of input signal
Adjust the PC-RGB input signal to fit the screen
Setting the Color Expression Range
12
Installation and User's Guide
4-2-1 Picture Mode
Picture Mode can select 4 modes as Mild, Dynamic, Standard and User as shown in the figure below.
Press the " ◀ , ▶ " key to change the mode.
Picture Mode Mild
Contrast 45
Brightness 48
Color 45
Sharpness 50
Tint 50
MENU
Picture Mode Dynamic
Contrast 60
Brightness 50
Color 60
Sharpness 60
Tint 50
MENU
Picture Mode Standard
Contrast 50
Brightness 50
Color 50
Sharpness 50
Tint 50
MENU
Picture Mode User
Contrast 60
Brightness 50
Color 60
Sharpness 60
Tint 50
MENU
Three of the four modes except for User mode are shipped with fixed values at the time of shipment from the factory.
User mode can be set with “ ◀ , ▶ ” keys by selecting each item below with “▲, ▼” key only in the User mode.
Contrast
Brightness
Color
Sharpness
Tint
Adjust difference in the color and brightness
Adjust the dark and light
Adjust for desired color intensity
Adjust for best clarity of outline detail
Adjust for natural flesh tones
4-2-2 Color Temperature
Color Temperature can select 4 modes as Cool, Medium, Warm and User as shown in the figure below.
Color Tempera.. Cool
Red 43
Green 50
Blue 68
Color Tempera.. Medium
Red 50
Green 50
Blue 55
Color Tempera.. Warm
Red 60
Green 50
Blue 25
Color Tempera.. User
Red 50
Green 50
Blue 50
MENU MENU MENU
Three modes except User mode are factory shipped with factory default values, and each color item (RED, GREEN, BLUE) is selected with the "▲, ▼" keys in the User mode only.
User settings are available.
MENU
13
Installation and User's Guide
4-2-3 Aspect Ratio
Aspect Ratio allows user to select the each aspect ratio as shown in the figure below.
(However, activated list is according to the input port and the input resolution.)
Aspect Ratio
Auto
4 : 3
16 : 9
Zoom1
Zoom2
Just Scan
MENU
4-2-4 Noise Reduction
Noise Reduction can select 5 modes as Off, Low, Middle, High, Default as shown in the figure below.
Noise Reduction
Off
Low
Middle
High
Default
MENU
4-2-5 Screen
Screen enables to set the active area of the display when using PC-RGB input port.
Screen
Auto Adjust
Horizontal Pos. 4
Vertical Pos. 91
Size 100
Phase 100
Screen
Auto Adjust
Horizontal Pos. 4
Vertical Pos. 91
Size 100
Phase 100
Screen
Auto Adjust
Horizontal Pos. 4
Vertical Pos. 91
Size 100
Phase 100
Screen
Auto Adjust
Horizontal Pos. 4
Vertical Pos. 91
Size 100
Phase 100
MENU MENU MENU MENU
Screen
Auto Adjust
Horizontal Pos. 4
Vertical Pos. 91
Size 100
Phase 100
MENU
Auto Adjust is an item to be set automatically, and the input signal should be operated in the signal state where the Outline has a lot of white color.
14
Installation and User's Guide
4-2-6 Color Range
Color Range sets the range of color expressions on the display.
(Press the “ ▶ SELECT” key to select either”0~255”, “16~235”)
4-3 SOUND Menu
SOUND
Sound Mode
Balance
Auto Volume
Surround Sound
EQ
Standard
0
Off
Off
PC-RGB:
The SOUND Menu can be selected from the following 5 modes by pressing the ▲ or ▼ key.
Sound Mode
Balance
Auto Volume
Surround Sound
EQ
Sound mode selection
Adjust Left and Right audio balance
Auto volume control for input audio
Surround Sound selection
Adjust Sound Equalizer
4-3-1 Sound Mode
Sound Mode can select 5 modes as Standard, Movie, Sports, Music and User as shown in the figure below.
SOUND Standard
Treble 50
Bass 50
SOUND
Treble 75
Bass 90
Movie SOUND
Treble 35
Bass 35
Sports SOUND
Treble 75
Bass 75
Music SOUND
Treble 50
Bass 50
User
MENU MENU MENU
Four modes except User mode are factory shipped with factory default values, and both item (Treble, Bass) is selected with the "▲, ▼" keys in the User mode only.
Each item set by pressing the " ◀ , ▶ ".
MENU MENU
15
Installation and User's Guide
4-3-2 Balance
Balance can adjust the left and right volume of audio and set by pressing the " ◀ , ▶ ".
Balance
0
MENU
4-3-3 Auto Volume
Control for input audio when pressing “ ▶ SELECT” key select On/Off.
4-3-4 Surround Sound
When pressing "▲, ▼" keys select from three modes as Off, Surround, SRS TruSurround XT by shown in the figure below.
Surround Sound
Off
Surround
SRS TruSurround XT
MENU
4-3-5 EQ
Equalizer Frequency is selected with the "▲, ▼" keys. each frequency adjust by pressing the " ◀ , ▶ ".
EQ
120Hz 50
500Hz 50
1.5KHz 50
5KHz 50
10KHz 50
MENU
16
Installation and User's Guide
4-4 Option Menu
OPTION
OSD Language
Blending
OsdDuration
Restore Factory Default
Software Update(USB)
Key Lock
DPMS
English
Low
Off
Off
On
PC-RGB:
The Option Menu can be selected from the following 6 modes by pressing the ▲ or ▼ key.
OSD Language
Blending
Selectable OSD Menu Language
Adjust blending for OSD Menu and Main window
OSD Duration Setting Duration time of OSD Menu
Restore Factory Default
Software Update(USB)
Key Lock
DPMS
When input signal is the no signal, DPMS "on" change the power saving mode.
4-4-1 OSD Language
As shown in the figure below, OSD Language can be se▲lected by "▲, ▼ " key.
OSD Language
English
Espaol
Franais
Deutsch
Italiano
MENU
17
Installation and User's Guide
4-4-2 Blending
OSD Menu Bleding can select 4 modes as Off, Low, Middle, High by pressing the “ ▶ SELECT” key.
4-4-3 OsdDuration
OSD menu Duration can select 4 modes as 5, 10, 15Sec and Off by pressing the “ ▶ SELECT” key.
4-4-4 Restore Factory Default
Restore factory default can be selected by pressing the " ▶ SELECT" key. Select Yes or No by the “ ◀ , ▶ " key.
Are you sure?
Yes No
4-4-5 Software Update(USB)
Sofrware update default can be selected by pressing the "Menu" key. Select Yes or No by the “ ◀ , ▶ " key.
Are you sure?
Software Update(USB)
48%
Yes No
18
4-4-6 Key Lock
Key lock default can be selected by pressing the " ▶ SELECT" key.
KEY LOCK ON KEY LOCK OFF
Installation and User's Guide
4-4-7 DPMS
The function can be activated(ON) or deactivated(OFF) with the button ▶ .
4-5 INPUT SOURCE
Input Source can be selected from the following four input modes by using the ▲ and ▼ keys when the window as shown below is displayed by pressing the "SOURCE / ▼" key in the Main window.
(Input Source can be selected by ▲ and ▼ key when window shown as below. To be in this menu, pressing the “SOURCE” / ▼" key in the Main window.)
Input Source
PC - RGB
HDMI2
HDMI1
AV 2
AV 1
OK
4-6 Audio Volume
Audio Volume can be increased or decreased by pressing "VOL- / ◀ ", "VOL + / ▶ " Key.
20
19
Installation and User's Guide
5. FEATURE
Display
Interface
Audio
Transmetter
Special
Features
Dimension
Cabinet
Power
General Features
Screen Size
Resolution
Pixel Pitch
Brightness
Contrast Ratio
Aspect Ratio
Viewing Angle(H/V)
Display Color
Response Time
Video System
Panel Life Time(hours)
Video In/Out(BNC Type)
VGA In(15Pin D-sub)
HDMI In
Audio In(RCA Type)
PC Stereo In
Built in Speakers
Remote Control
Filter Type
Deinterlacing
Noise reduction
Multi Lingual Language
Outline Dimension(w Stand)
Cabinet color/Base Stand
Cabinet Material
Electrical Ratings
Circumstance
Mounts
Options
Operating Temperature
Storage Temperautre
VESA Mounts Size
Ceiling Mount
Wall
Rack Mount
LCD Protection Glass
VCM-19LEDMD
19.0 inches
1280*1024 pixels
0.293*0.293 mm
250cd/m²
1000 : 1
5 : 4
178/178 degress
16.7 million
14 ms
NTSC / PAL
30,000 hours
2/2
1
2
2
1
Y(1W*2)
Y
3D Comb Filter
Y
Y
Eng, Spa, Fre, Ger, Ita
16.38*3.43*14.37 inches
Black/Tilt Back
Electro-Galvanized Steel
AC 100~240V(50/60Hz)
DC 12V
0~40 celsius
-20~60 celsius
100*100 mm
CMK-01
WB-5, 10, 30, 31
RMK-08
Y
20
Installation and User's Guide
6. TROUBLESHOOTING
* When the following troubles are occurred, follow the trouble shooting. Before contacting service center.
Troubleshooting
The screen doesn’t show up
Troubleshooting Tip
1. Make sure if the power supply is connected property
2. Turn on the power.
3. Select the input signal right for the connected port.
The screen is too light or to dark
The screen size is not fit for the PC signal
Control the BRIGHTNESS
Press the AUTO key among keys in the front.
(It is used only in the PC signal)
The screen color shows strange in the PC signal
In the FUNCTION menu of OSD menu, perform the
AUTOADJUST.
The key pad does not work Press ▲ and ◄ button on the key pad for 10 seconds.
21
eneo® is a registered trademark of
VIDEOR E. Hartig GmbH
Exclusive distribution through specialised trade channels only.
VIDEOR E. Hartig GmbH
Carl-Zeiss-Straße 8
63322 Rödermark/Germany
Tel. +49 (0) 6074 / 888-0
Fax +49 (0) 6074 / 888-100 www.videor.com
www.eneo-security.com
Technical changes reserved
© Copyright by VIDEOR E. Hartig GmbH
Version
11
/201
7

Public link updated
The public link to your chat has been updated.
Advertisement