HP E344c 34-inch Curved Monitor User Guide 36 Pages
advertisement
User Guide
© Copyright 2019 HP Development Company,
L.P.
Windows is either a registered trademark or trademark of Microsoft Corporation in the
United States and/or other countries. HDMI, the
HDMI Logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI Licensing LLC.
DisplayPort™ and the DisplayPort™ logo are trademarks owned by the Video Electronics
Standards Association (VESA) in the United
States and other countries.
The information contained herein is subject to change without notice. The only warranties for
HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Product notice
This guide describes features that are common to most models. Some features may not be available on your product. To access the latest user guide, go to http://www.hp.com/support , and follow the instructions to find your product. Then select User Guides.
First Edition: July 2019
Document Part Number: L57244-001
About This Guide
This guide provides information about monitor features, setting up the monitor, using the software and technical specifications.
WARNING!
Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
IMPORTANT: Indicates information considered important but not hazard-related (for example, messages related to property damage). A notice alerts the user that failure to follow a procedure exactly as described could result in loss of data or in damage to hardware or software. Also contains essential information to explain a concept or to complete a task.
NOTE: Contains additional information to emphasize or supplement important points of the main text.
TIP: Provides helpful hints for completing a task.
This product incorporates HDMI technology.
iii
iv About This Guide
Table of contents
v
vi
1 Getting Started
Important safety information
A power cord is included with the monitor. If you use another cord, use only a power source and connection appropriate for this monitor. For information about the correct power cord set to use with the monitor, refer to the Product Notices provided in your documentation kit.
WARNING!
To reduce the risk of electric shock:
• Plug the power cord into an AC outlet that is easily accessible at all times.
• If the power cord has a 3-pin attachment plug, plug the cord into a grounded (earthed) 3-pin outlet.
For your safety, do not place anything on power cords or cables. Care should be taken to route all cords and cables connected to the monitor so that they cannot be stepped on, pulled, grabbed, or tripped over.
To reduce the risk of serious injury, read the Safety & Comfort Guide provided with your user guides. It describes proper workstation setup and proper posture, health, and work habits for computer users. The
Safety & Comfort Guide also provides important electrical and mechanical safety information. The Safety &
Comfort Guide is also available on the Web at http://www.hp.com/ergo .
IMPORTANT: For the protection of the monitor and the computer, connect all power cords for the computer and its peripheral devices (such as a monitor, printer, scanner) to a surge protection device such as a power strip or uninterruptible power supply (UPS). Not all power strips provide surge protection; the power strip must be specifically labeled as having this capability. Use a power strip whose manufacturer offers a damage replacement policy so you can replace the equipment if surge protection fails.
Use the appropriate and correctly sized furniture designed to properly support your monitor.
WARNING!
Monitors that are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, or carts may fall over and cause personal injury.
NOTE: This product is suitable for entertainment purposes. Consider placing the monitor in a controlled luminous environment to avoid interference from surrounding light and bright surfaces that may cause disturbing reflections from the screen.
Important safety information 1
Product features and components
Features
The monitor includes the following features:
● 86.4 cm (34 in) diagonal viewable screen area with 3440 × 1440 resolution, plus full-screen support for lower resolutions; includes custom scaling for maximum image size while preserving original aspect ratio
● Nonglare panel with an LED backlight
● Wide viewing angle to allow viewing from a sitting or standing position, or when moving from side to side
● Tilt, swivel, and height adjustment capabilities
● Removable stand for flexible monitor head mounting solutions
● DisplayPort™ video input (cable provided)
NOTE: Cables and/or adapters (purchased separately) may be required.
● High-Definition Multimedia Interface (HDMI) video input
NOTE: Cables and/or adapters (purchased separately) may be required.
● USB hub with two upstream ports (connect to the computer): one USB Type-C (USB 3.1) and one USB
Type-B (USB 3.0); and four downstream ports: three USB Type-A and one USB Type-C (connect to USB devices)
● USB cable provided to connect the monitor's USB hub to the USB port on the computer
● Plug and Play capability, if supported by your operating system
● Security cable slot provision on rear of monitor for optional security cable
● On-screen display (OSD) adjustments in several languages for easy setup and screen optimization
● HP Display Assistant software for adjusting monitor settings and enabling the theft deterrence features
● High-bandwidth Digital Content Protection (HDCP) copy protection on all digital inputs
● Energy saver feature to meet requirements for reduced power consumption
NOTE: For safety and regulatory information, refer to the Product Notices provided in your documentation kit. To access the latest user guide, go to http://www.hp.com/support and follow the instructions to find your product. Then select User Guides.
2 Chapter 1 Getting Started
Rear components
Table 1-1 Rear components
Component
6
7
8
4
5
1
2
3
Security cable slot
Power connector
HDMI port
DisplayPort connector
USB Type-C port (upstream)
USB Type-B port (upstream)
USB Type-A ports (2) (downstream)
USB Type-A port (downstream)
9 USB Type-C port with 15 W charging
(downstream)
Function
Connects an optional security cable to the monitor.
Connects the power cord.
Connects an HDMI cable from the monitor to a source device such as a computer.
Connects the DisplayPort cable from the monitor to a source device such as a computer.
Connects the USB CM-CM cable from the monitor to a source device such as a computer.
Connects a USB Type-B cable from the monitor to a source device such as a computer.
Connect USB cables to peripheral devices, such as a keyboard, mouse, or USB hard drive, and provide data transfer.
Connects a USB cable to a peripheral USB device, such as a keyboard, mouse, or USB hard drive, and provides data transfer.
Connects a USB Type-C cable to a peripheral USB device, provides data transfer, and even when the monitor is in Sleep mode, charges most devices such as a smart phone or tablet.
NOTE: Cables and/or adapters (purchased separately) may be required.
Product features and components 3
Front components
3
4
1
2
Table 1-2 Front components
Control
Menu button
Function buttons
Power button
Power light
Function
Press to open the OSD menu, select a menu item from the OSD, or close the OSD menu.
Use these buttons to navigate through the OSD menu based on the indicators above the buttons that are activated while the OSD menu is open.
NOTE: You can reconfigure the function buttons in the OSD menu to quickly select the most commonly used operations. See
Using the function buttons on page 16
for more information.
Turns the monitor on or off.
White: The monitor is on.
Amber: Monitor is in a reduced power state because of inactivity. See Using Auto-Sleep
.
Setting up the monitor
WARNING!
To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation setup and proper posture, health, and work habits for computer users. The Safety & Comfort
Guide also provides important electrical and mechanical safety information. The Safety & Comfort Guide is available on the Web at http://www.hp.com/ergo .
IMPORTANT: To prevent damage to the monitor, do not touch the surface of the LCD panel. Pressure on the panel may cause nonuniformity of color or disorientation of the liquid crystals. If this occurs, the screen will not recover to its normal condition.
IMPORTANT: To prevent the screen from getting scratched, defaced, or broken and prevent damage to the control buttons, position the monitor facedown on a flat surface covered with protective sheet foam or a nonabrasive cloth.
4 Chapter 1 Getting Started
Installing the monitor stand
TIP: Consider the placement of the monitor, because surrounding light and bright surfaces might cause interfering reflections.
1.
With the monitor placed facedown inside the box, lower the bottom of the stand's mounting plate into the back of the monitor’s recess (1) until it snaps into place (2).
2.
With the monitor still placed facedown inside the box: a.
Insert the base into the bottom of the monitor stand (1).
b.
Swivel the base counterclockwise to lock it in place (2).
c.
Confirm that the red arrow on the monitor stand is aligned with the green arrow on the bottom of the base (3).
d.
Then insert the two thumbscrews into the base and tighten them (4).
Setting up the monitor 5
Mounting the monitor head
The monitor head can be attached to a wall, swing arm, or other mounting fixture.
NOTE: This apparatus is intended to be supported by a GS and UL–listed or GS and CSA–listed wall-mount bracket.
Removing the monitor stand
You can remove the monitor head from the stand to install the monitor head on a wall, a swing arm, or other mounting fixture.
IMPORTANT: Before disassembling the monitor, be sure that the monitor is turned off and all cables are disconnected.
1.
Disconnect and remove all cables from the monitor.
2.
Position the monitor facedown in the original packing box.
3.
Push up on the latch near the bottom center of the monitor (1).
4.
Lift the bottom of the stand straight up until the mounting plate clears the recess in the panel (2), and then lift the stand off the monitor head (3).
6 Chapter 1 Getting Started
Attaching the VESA mounting bracket
1.
Remove the four screws from the VESA® holes located on the rear of the monitor head.
2.
Attach the VESA mounting bracket (included with your monitor) to the back of the monitor head. Fit the four tabs on the upper part of the VESA adapter to the groove on the back of the monitor and press the
VESA adapter down until it snaps into place.
Setting up the monitor 7
3.
Attach the monitor to the wall or swing arm of your choice by inserting the four VESA screws provided with the VESA mounting bracket.
IMPORTANT: Use the four new VESA screws that are attached to the new mounting bracket. Do not reuse the four VESA screws that you removed from the back of the monitor head. These screws are not long enough to provide a secure connection.
Connecting the cables
NOTE: The monitor ships with select cables. Not all cables shown in this section are included with the monitor.
1.
Place the monitor in a convenient, well-ventilated location near the computer.
2.
Before connecting the cables, route the cables through the cable routing hole in the center of the stand.
3.
Connect a video cable.
NOTE: The monitor automatically determines which inputs have valid video signals. To select any input manually, open the OSD and select Input.
● Connect one end of a DisplayPort cable to the DisplayPort connector on the rear of the monitor and the other end to the DisplayPort connector on the source device.
8 Chapter 1 Getting Started
● Connect one end of an HDMI cable to the HDMI port on the rear of the monitor and the other end to the HDMI port on the source device.
Setting up the monitor 9
● Connect a USB CM to CM cable to the USB Type-C port on the monitor. Then connect the Type-C connector to the USB downstream port on the source device.
NOTE: The USB CM to CM cable provides power delivery up to 15 W (5V, 3A).
4.
Connect a USB Type-A to Type-B cable to the USB Type-B port on the rear of the monitor and the other end to a USB port on the source device.
NOTE: You must connect the USB Type-C upstream cable or USB Type-B upstream cable from the source device (computer) to the rear of the monitor to enable the USB Type-A and USB Type-C downstream ports on the monitor. For more information, see
Connecting USB devices on page 11
.
10 Chapter 1 Getting Started
5.
Connect one end of the power cord to the power connector on the rear of the monitor and the other end to a grounded AC outlet.
WARNING!
To reduce the risk of electric shock or damage to the equipment:
Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
Plug the power cord into a grounded (earthed) AC outlet that is easily accessible at all times.
Disconnect power from the equipment by unplugging the power cord from the AC outlet.
For your safety, do not place anything on power cords or cables. Arrange them so that no one may accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging the power cord from the AC outlet, grasp the cord by the plug.
Connecting USB devices
USB ports are used to connect devices such as a digital camera, USB keyboard, or USB mouse. There are four downstream USB ports on the monitor: two USB Type-A downstream on the rear, and one USB Type-C and one
USB Type-A downstream on the rear side.
NOTE: You must connect the USB Type-C upstream cable or USB Type-B upstream cable from the source device (computer) to the rear of the monitor to enable the USB Type-A and USB Type-C downstream ports on the monitor.
Setting up the monitor 11
Table 1-3 USB port locations
USB Ports
(1)
(2)
(3)
USB Type-A and USB Type-C downstream ports
USB Type-C or USB Type-B upstream port from computer
USB Type-A downstream ports
Adjusting the monitor
WARNING!
To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation setup and proper posture, health, and work habits for computer users. The Safety & Comfort
Guide also provides important electrical and mechanical safety information. The Safety & Comfort Guide is available on the Web at http://www.hp.com/ergo .
NOTE: Do not touch the front of the monitor screen. When adjusting the tilt, swivel, and height, place a hand on the left and right side of the back of the monitor head and adjust as needed.
1.
Tilt the monitor head forward or backward to set it to a comfortable eye level.
12 Chapter 1 Getting Started
2.
Swivel the monitor head to the left or right for the best viewing angle.
3.
Adjust the monitor’s height to a comfortable position for your individual workstation. The monitor’s top bezel edge should not exceed a height that is parallel to your eye height. A monitor that is positioned low and reclined may be more comfortable for users with corrective lenses. The monitor should be repositioned as you adjust your working posture throughout the work day.
Turning on the monitor
IMPORTANT: Burn-in image damage may occur on monitors that display the same static image on the screen for 12 or more consecutive hours. To avoid burn-in image damage, you should always activate a screen saver application or turn off the monitor when it will not be in use for a prolonged period of time. Image retention is a condition that may occur on all LCD screens. Burn-in damage on the monitor is not covered under the HP warranty.
NOTE: If pressing the power button has no effect, the Power Button Lockout feature may be enabled. To disable this feature, press and hold the monitor power button for 10 seconds.
NOTE: You can disable the power light in the OSD menu. Press the Menu button to open the OSD, and then select Power, select Power LED, and then select Off.
Setting up the monitor 13
1.
Press the power button on the computer to turn it on.
2.
Press the power button on the bottom of the monitor to turn it on.
When the monitor is first turned on, a monitor status message displays for five seconds. The message shows which input is the current active signal, the status of the auto-switch source setting (On or Off; default setting is On), the current preset screen resolution, and the recommended preset screen resolution.
The monitor automatically scans the signal inputs for an active input and uses that input for the display.
Installing a security cable
You can secure the monitor to a fixed object with an optional security cable available from HP.
14 Chapter 1 Getting Started
2 Using the monitor
Software and utilities
You can download and install the following files from http://www.hp.com/support :
● INF (Information) file
● ICM (Image Color Matching) files
● HP Display Assistant: Adjusts the monitor settings and enables theft deterrence features
To download the files:
1.
Go to http://www.hp.com/support .
2.
Select Software and Drivers.
3.
Select your product type.
4.
Enter your HP monitor model in the search field and follow the on-screen instructions.
The Information file
The INF file defines monitor resources used by Windows® operating systems to ensure monitor compatibility with the computer’s graphics adapter.
This monitor is Microsoft Windows Plug and Play–compatible and the monitor will work correctly without installing the INF file. Monitor Plug and Play-compatibility requires that the computer’s graphic card is VESA
DDC2–compliant and that the monitor connects directly to the graphics card. Plug and Play does not work through separate BNC-type connectors or through distribution buffers/boxes.
The Image Color Matching file
The ICM files are data files that are used in conjunction with graphics programs to provide consistent color matching from monitor screen to printer, or from scanner to monitor screen. This file is activated from within graphics programs that support this feature.
NOTE: The ICM color profile is written in accordance with the International Color Consortium (ICC) Profile
Format specification.
Software and utilities 15
Using the OSD menu
Use the OSD menu to adjust the screen image based on your viewing preferences. You can access and make adjustments in the OSD menu using the buttons on the monitor's front bezel.
NOTE: Changing the default settings may increase power consumption.
To access the OSD menu and make adjustments, do the following:
1.
If the monitor is not already on, press the power button to turn on the monitor.
2.
Press the Menu button.
3.
Use the three function buttons to navigate, select, and adjust the menu choices. The on-screen button labels vary depending on which menu or submenu is active.
The following table lists menu selections in the OSD main menu.
Table 2-1 OSD main menu
Main Menu Description
Brightness+
Color
Image
Input
Power
Menu
Management
Information
Exit
Adjusts the brightness and contrast levels of the screen.
Selects and adjusts the screen color.
Adjusts the screen image.
Selects the video input signal.
Adjusts the power settings.
Adjusts the on-screen display (OSD) and function button controls.
Adjusts the USB host and DDC/CI settings and returns all OSD menu settings to the factory default settings.
Selects and displays important information about the monitor.
Exits the OSD menu screen.
Using the function buttons
Pressing one of the three function buttons activates the buttons and displays the icons above the buttons.
The factory default button icons and functions are shown in the following table.
Table 2-2 Button names and functions
Button
1 Menu button
2 Information button
(function button 3- assignable)
Function
Opens the OSD main menu, selects a menu item from the OSD, or closes the OSD menu.
Opens the Information menu.
16 Chapter 2 Using the monitor
Table 2-2 Button names and functions (continued)
Button Function
3
4
Viewing Modes button
(function button 2 - assignable)
Next Active Input button
(function button 1 - assignable)
Opens the Viewing Modes menu where you can adjust the monitor screen to a comfortable viewing light or select a preset viewing mode.
Switches the monitor’s input source to the next active input.
Reassigning the function buttons
You can change the assignable function buttons from their default values so that when the buttons are activated you can quickly access commonly used menu items. You cannot reassign the Menu button.
To reassign the function buttons:
1.
Press the Menu button to open the OSD menu.
2.
Select Menu, select Assign Buttons, and then select one of the available options for the button you want to assign.
NOTE: To view an OSD menu simulator, visit the HP Customer Self Repair Services Media Library at http://www.hp.com/go/sml .
Adjusting blue light output (select products only)
Decreasing the blue light emitted by the monitor reduces the blue light exposure to your eyes. This monitor allows you to select a setting to reduce blue light output and create a more relaxing and less stimulating image while you read content on the screen.
To adjust the blue light output from the monitor:
1.
Press one of the rear panel OSD buttons to activate the buttons, and then press the Menu button to open the OSD. Select Color and Viewing Mode.
2.
Select the setting that you want.
● Low Blue Light: (TUV certified) Reduces blue light for improved eye comfort.
● Night: Adjusts to the lowest blue light and reduces the impact on sleep.
● Reading: Optimizes blue light and brightness for indoor viewing.
3.
Select Save and Return to save your setting and close the menu. Select Cancel if you do not want to save the setting.
4.
In the Main menu, select Exit.
Using Auto-Sleep Mode
The monitor supports an on-screen display (OSD) menu option called Auto-Sleep Mode that allows you to enable or disable a reduced power state for the monitor. When Auto-Sleep Mode is enabled, the monitor enters a reduced power state when the host computer signals low power mode in the absence of either horizontal or vertical sync signal. Auto-Sleep Mode is enabled by default.
Reassigning the function buttons 17
Upon entering this reduced power state (sleep mode), the monitor screen is blanked, the backlight is turned off, and the power light indicator turns amber. The monitor draws less than 0.5 W of power when in this reduced power state. The monitor wakes from the sleep mode when the host device sends an active signal to the monitor (for example, if you activate the mouse or keyboard).
To disable Auto-Sleep Mode:
1.
Press the Menu button to open the OSD.
2.
In the OSD menu, select Power, select Auto-Sleep Mode, and then select Off.
Changing the Power Mode setting
When in sleep mode, to comply with international power standards, the monitor default setting is Power
Saver mode. If your display supports Performance mode, then to keep the USB ports enabled even when the monitor is in Auto-Sleep Mode, change the Power Mode setting from Power Saver to Performance.
To change the Power Mode setting:
1.
Press the Menu button to open the OSD menu.
2.
Select Power, select Power Mode, and then select Performance.
3.
Select Save and close the OSD.
18 Chapter 2 Using the monitor
3 Support and troubleshooting
Solving common issues
The following table lists possible issues, the possible cause of each issue, and the recommended solutions.
Table 3-1 Common issues and solutions
Issue
Screen is blank or video is flashing.
Possible Cause
Power cord is disconnected.
Solution
Connect the power cord.
Image appears blurred, indistinct, or too dark.
Check Video Cable is displayed on screen.
Input Signal Out of Range is displayed on screen.
The monitor is off but it did not seem to enter into sleep mode.
OSD Lockout is displayed.
Monitor is turned off.
Press the front bezel power button.
NOTE: If pressing the power button has no effect, press and hold the power button for 10 seconds to disable the Power
Button Lockout feature.
Video cable is improperly connected.
Connect the video cable properly. See
Connecting the cables on page 8
for more information.
System is in sleep mode.
Video card is incompatible.
Press any key on the keyboard or move the mouse to exit sleep mode.
Open the OSD menu and select the Input Control menu. Set
Auto-Switch Input to Off and manually select the input.
Brightness is too low.
Open the OSD menu and select Brightness to adjust the brightness scale as needed.
Monitor video cable is disconnected.
Connect the appropriate video signal cable between the computer and monitor. Be sure that the computer power is off while you connect the video cable.
Video resolution and/or refresh rate are set higher than what the monitor supports.
The monitor's power saving control is disabled.
Open the OSD menu and select Power Control > Auto-Sleep
Mode and set auto-sleep to On.
Power Button Lockout is displayed.
The monitor's OSD Lockout function is enabled.
The monitor's Power Button Lockout function is enabled.
Press and hold the Menu button on the front bezel for 10 seconds to disable the OSD Lockout function.
Press and hold the power button for 10 seconds to disable the
Power Button Lockout function.
Button lockouts
Holding down the power button or Menu button for 10 sec. will lock out the functionality of the buttons. You can restore the functionality by holding the buttons down again for 10 sec. This functionality is only available when the monitor is turned on, displaying an active signal, and the OSD is not open.
Solving common issues 19
Contacting support
To resolve a hardware or software problem, go to http://www.hp.com/support . Use this site to get more information about your product, including links to discussion forums and instructions on troubleshooting. You can also find information on how to contact HP and open a support case.
NOTE: The monitor user guide, reference material, and drivers are available at http://www.hp.com/support .
NOTE: Contact customer support to replace the power cord, the AC adapter (select products only), or any other cables that shipped with your monitor.
Preparing to call technical support
If you cannot solve a problem using the troubleshooting tips in this section, you may need to call technical support. Have the following information available when you call:
● Monitor model number
● Monitor serial number
● Purchase date on invoice
● Conditions under which the problem occurred
● Error messages received
● Hardware configuration
● Name and version of the hardware and software you are using
Locating the serial number and product number
The serial number and product number are located on a label on the bottom of the monitor head. You may need these numbers when contacting HP about the monitor model.
NOTE: You may need to partially pivot the monitor head to read the label.
20 Chapter 3 Support and troubleshooting
4 Maintaining the monitor
Maintenance guidelines
To enhance the performance and extend the life of the monitor:
● Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those controls that are covered in the operating instructions. If the monitor is not operating properly or has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider.
● Use only a power source and connection appropriate for this monitor, as indicated on the label or back plate of the monitor.
● Be sure that the total ampere rating of the products connected to the outlet does not exceed the current rating of the AC outlet and that the total ampere rating of the products connected to the cord does not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS or A) for each device.
● Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
● Turn the monitor off when it is not in use and use a screen saver program. Doing this can substantially increase the life expectancy of the monitor.
NOTE: A burned-in image on the monitor is not covered under the HP warranty.
● Never block the slots and openings of the cabinet or push objects into them. These openings provide ventilation.
● Do not drop the monitor or place it on an unstable surface.
● Do not allow anything to rest on the power cord. Do not walk on the cord.
● Keep the monitor in a well-ventilated area, away from excessive light, heat, or moisture.
Cleaning the monitor
1.
Turn off the monitor and unplug the power cord from the AC outlet.
2.
Disconnect any external devices.
3.
Dust the monitor by wiping the screen and the cabinet with a soft, clean antistatic cloth.
4.
For more difficult cleaning situations, use a 50/50 mix of water and isopropyl alcohol.
IMPORTANT: Do not use cleaners that contain any petroleum-based materials such as benzene, thinner, or any volatile substance to clean the monitor screen or cabinet. These chemicals may damage the monitor.
IMPORTANT: Spray the cleaner onto a cloth and use the damp cloth to gently wipe the screen surface.
Never spray the cleaner directly on the screen surface. It may run behind the bezel and damage the electronics. The cloth should be moist, but not wet. Water dripping into the ventilation openings or other points of entry can cause damage to the monitor. Allow the monitor to air-dry before use.
Maintenance guidelines 21
Shipping the monitor
Keep the original packing box in a storage area. You may need it later if you ship the monitor or move.
22 Chapter 4 Maintaining the monitor
A Technical specifications
NOTE: All specifications represent the typical specifications provided by HP’s component manufacturers; actual performance may vary either higher or lower.
For the latest specifications or additional specifications on this product, go to http://www.hp.com/go/ quickspecs/ and search for your specific monitor model to find the model-specific QuickSpecs.
86.4 cm/34 in model specifications
Table A-1 86.4 cm/34 in model specifications
Specification
Display, wide-screen
Type
Viewable image size
Maximum weight (unpacked)
Dimensions (include base)
Height (highest position)
Height (lowest position)
Depth
Width
Tilt
Swivel
Environmental requirements temperature
Measurement
86.4 cm
SVA
86.4 cm diagonal
11.00 kg
54.2 cm
39.2 cm
22 cm
80.92 cm
-5° to 20°
30° ± 1°
Operating temperature
Storage temperature
Storage humidity
Power source
Input terminal
5 to 35° C
-34 to 60° C
100–240 VAC 50/60 Hz
One HDMI port, one DisplayPort connector, and one USB Type-C DisplayPort connector
34 inch
34 inch diagonal
24.3 lbs
21.3 inches
15.4 inches
8.66 inches
31.85 inches
41 to 95° F
-29 to 140° F
5% to 95%
86.4 cm/34 in model specifications 23
Preset display resolutions
The following display resolutions are the most commonly used modes and are set as factory defaults. The monitor automatically recognizes these preset modes, and they will appear properly sized and centered on the screen.
86.4 cm/34 in model
Table A-2 Preset display resolutions
Preset Pixel format Horz freq (kHz)
12
13
14
15
8
9
10
11
4
5
6
7
1
2
3
16
17
18
19
20
21
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
1024 × 768
1024 × 768
1280 × 720
1280 × 800
1280 × 1024
1280 × 1024
1440 × 900
1600 × 900
1680 × 1050
1920 × 1080
1920 × 1200
1600 × 1200
2560 × 1080
2560 × 1440
3440 × 1440
3440 × 1440
45.000
49.702
63.981
79.976
55.935
60.000
65.290
67.500
31.469
37.500
31.469
37.879
46.875
48.363
60.023
74.556
75.000
66.000
88.787
43.819
88.819
Vert freq (Hz)
60.000
59.810
60.020
75.025
59.887
60.000
59.954
60.000
59.940
75.000
70.087
60.317
75.000
60.004
75.029
59.885
60.000
60.000
59.951
30.000
59.973
Table A-3 Preset timing resolutions
2
3
Preset
1
4
Timing name
480p
480p
576p
720p50
Pixel format
640 × 480
720 × 480
720 × 576
1280 × 720
Horz freq (kHz) Vert freq (Hz)
31.469
59.940
31.469
31.250
37.500
59.940
50.000
50.000
24 Appendix A Technical specifications
Table A-3 Preset timing resolutions (continued)
Preset Timing name Pixel format Horz freq (kHz) Vert freq (Hz)
5
6
7
8
9
10
11
12
720p60
1080p50
1080p60
1280 × 720
1920 × 1080
1920 × 1080
1600×1200p60 1600 × 1200
1900×1200p60 1920 × 1200
2560×1080p60 2560 × 1080
2560×1440p60 2560 × 1440
3440×1440p30 3440 × 1440
45.000
56.250
67.500
75.000
74.560
66.000
88.787
43.819
60.000
50.000
60.000
60.000
59.880
60.000
59.950
30.000
Energy saver feature
The monitors support a reduced power state. The reduced power state is initiated if the monitor detects the absence of either the horizontal sync signal or the vertical sync signal. Upon detecting the absence of these signals, the monitor screen is blanked, the backlight is turned off, and the power light turns amber. When the monitor is in the reduced power state, the monitor uses <0.5 W of power. There is a brief warm-up period before the monitor returns to its normal operating state.
See the computer manual for instructions on setting energy saver features (sometimes called power management features).
NOTE: The previous power saver feature only works when the monitor is connected to a computer that has energy saver features.
By selecting the settings in the monitor's Energy Saver utility, you can also program the monitor to enter into the reduced power state at a predetermined time. When the monitor's Energy Saver utility causes the monitor to enter the reduced power state, the power light blinks amber.
Energy saver feature 25
B Accessibility
HP and accessibility
Because HP works to weave diversity, inclusion, and work/life into the fabric of the company, it is reflected in everything HP does. HP strives to create an inclusive environment focused on connecting people to the power of technology throughout the world.
Finding the technology tools you need
Technology can unleash your human potential. Assistive technology removes barriers and helps you create independence at home, at work, and in the community. Assistive technology helps increase, maintain, and improve the functional capabilities of electronic and information technology. For more information, see
Finding the best assistive technology on page 27
.
The HP commitment
HP is committed to providing products and services that are accessible for people with disabilities. This commitment supports the company's diversity objectives and helps ensure that the benefits of technology are available to all.
The HP accessibility goal is to design, produce, and market products and services that can be effectively used by everyone, including people with disabilities, either on a stand-alone basis or with appropriate assistive devices.
To achieve that goal, this Accessibility Policy establishes seven key objectives to guide HP actions. All HP managers and employees are expected to support these objectives and their implementation in accordance with their roles and responsibilities:
● Raise the level of awareness of accessibility issues within HP, and provide employees with the training they need to design, produce, market, and deliver accessible products and services.
● Develop accessibility guidelines for products and services, and hold product development groups accountable for implementing these guidelines where competitively, technically, and economically feasible.
● Involve people with disabilities in the development of accessibility guidelines and in the design and testing of products and services.
● Document accessibility features, and make information about HP products and services publicly available in an accessible form.
● Establish relationships with leading assistive technology and solution providers.
● Support internal and external research and development that improves assistive technology relevant to
HP products and services.
● Support and contribute to industry standards and guidelines for accessibility.
International Association of Accessibility Professionals (IAAP)
IAAP is a not-for-profit association focused on advancing the accessibility profession through networking, education, and certification. The objective is to help accessibility professionals develop and advance their careers and to better enable organizations to integrate accessibility into their products and infrastructure.
26 Appendix B Accessibility
As a founding member, HP joined to participate with other organizations to advance the field of accessibility.
This commitment supports HP’s accessibility goal of designing, producing, and marketing products and services that people with disabilities can effectively use.
IAAP will make the profession strong by globally connecting individuals, students, and organizations to learn from one another. If you are interested in learning more, go to http://www.accessibilityassociation.org
to join the online community, sign up for newsletters, and learn about membership options.
Finding the best assistive technology
Everyone, including people with disabilities or age-related limitations, should be able to communicate, express themselves, and connect with the world using technology. HP is committed to increasing accessibility awareness within HP and with our customers and partners. Whether it’s large fonts that are easy on the eyes, voice recognition that lets you give your hands a rest, or any other assistive technology to help with your specific situation—a variety of assistive technologies make HP products easier to use. How do you choose?
Assessing your needs
Technology can unleash your potential. Assistive technology removes barriers and helps you create independence at home, at work, and in the community. Assistive technology (AT) helps increase, maintain, and improve the functional capabilities of electronic and information technology.
You can choose from many AT products. Your AT assessment should allow you to evaluate several products, answer your questions, and facilitate your selection of the best solution for your situation. You will find that professionals qualified to do AT assessments come from many fields, including those licensed or certified in physical therapy, occupational therapy, speech/language pathology, and other areas of expertise. Others, while not certified or licensed, can also provide evaluation information. You will want to ask about the individual's experience, expertise, and fees to determine if they are appropriate for your needs.
Accessibility for HP products
The following links provide information about accessibility features and assistive technology, if applicable, included in various HP products. These resources will help you select the specific assistive technology features and product(s) most appropriate for your situation.
● HP Elite x3–Accessibility Options (Windows 10 Mobile)
● HP PCs–Windows 7 Accessibility Options
● HP PCs–Windows 8 Accessibility Options
● HP PC’s–Windows 10 Accessibility Options
● HP Slate 7 Tablets–Enabling Accessibility Features on Your HP Tablet (Android 4.1/Jelly Bean)
● HP SlateBook PCs–Enabling Accessibility Features (Android 4.3, 4.2/Jelly Bean)
● HP Chromebook PCs–Enabling Accessibility Features on Your HP Chromebook or Chromebox (Chrome
OS)
● HP Shopping–peripherals for HP products
If you need additional support with the accessibility features on your HP product, see
.
Additional links to external partners and suppliers that may provide additional assistance:
● Microsoft Accessibility information (Windows 7, Windows 8, Windows 10, Microsoft Office)
● Google Products accessibility information (Android, Chrome, Google Apps)
HP and accessibility 27
● Assistive Technologies sorted by impairment type
● Assistive Technologies sorted by product type
● Assistive Technology vendors with product descriptions
● Assistive Technology Industry Association (ATIA)
Standards and legislation
Standards
Section 508 of the Federal Acquisition Regulation (FAR) standards was created by the US Access Board to address access to information and communication technology (ICT) for people with physical, sensory, or cognitive disabilities. The standards contain technical criteria specific to various types of technologies, as well as performance-based requirements which focus on functional capabilities of covered products. Specific criteria cover software applications and operating systems, web-based information and applications, computers, telecommunications products, video and multimedia, and self-contained closed products.
Mandate 376 – EN 301 549
The EN 301 549 standard was created by the European Union within Mandate 376 as the basis for an online toolkit for public procurement of ICT products. The standard specifies the functional accessibility requirements applicable to ICT products and services, together with a description of the test procedures and evaluation methodology for each accessibility requirement.
Web Content Accessibility Guidelines (WCAG)
Web Content Accessibility Guidelines (WCAG) from the W3C's Web Accessibility Initiative (WAI) helps web designers and developers create sites that better meet the needs of people with disabilities or age-related limitations. WCAG advances accessibility across the full range of web content (text, images, audio, and video) and web applications. WCAG can be precisely tested, is easy to understand and use, and allows web developers flexibility for innovation. WCAG 2.0 has also been approved as ISO/IEC 40500:2012 .
WCAG specifically addresses barriers to accessing the web experienced by people with visual, auditory, physical, cognitive, and neurological disabilities, and by older web users with accessibility needs. WCAG 2.0 provides characteristics of accessible content:
● Perceivable (for instance, by addressing text alternatives for images, captions for audio, adaptability of presentation, and color contrast)
● Operable (by addressing keyboard access, color contrast, timing of input, seizure avoidance, and navigability)
● Understandable (by addressing readability, predictability, and input assistance)
● Robust (for instance, by addressing compatibility with assistive technologies)
Legislation and regulations
Accessibility of IT and information has become an area of increasing legislative importance. The links listed below provide information about key legislation, regulations, and standards.
● United States
● Canada
● Europe
28 Appendix B Accessibility
● United Kingdom
● Australia
● Worldwide
Useful accessibility resources and links
The following organizations might be good resources for information about disabilities and age-related limitations.
NOTE: This is not an exhaustive list. These organizations are provided for informational purposes only. HP assumes no responsibility for information or contacts you encounter on the Internet. Listing on this page does not imply endorsement by HP.
Organizations
● American Association of People with Disabilities (AAPD)
● The Association of Assistive Technology Act Programs (ATAP)
● Hearing Loss Association of America (HLAA)
● Information Technology Technical Assistance and Training Center (ITTATC)
● Lighthouse International
● National Association of the Deaf
● National Federation of the Blind
● Rehabilitation Engineering & Assistive Technology Society of North America (RESNA)
● Telecommunications for the Deaf and Hard of Hearing, Inc. (TDI)
● W3C Web Accessibility Initiative (WAI)
Educational institutions
● California State University, Northridge, Center on Disabilities (CSUN)
● University of Wisconsin - Madison, Trace Center
● University of Minnesota computer accommodations program
Other disability resources
● ADA (Americans with Disabilities Act) Technical Assistance Program
● ILO Global Business and Disability network
● EnableMart
● European Disability Forum
● Job Accommodation Network
● Microsoft Enable
Useful accessibility resources and links 29
HP links
Our contact webform
HP comfort and safety guide
HP public sector sales
Contacting support
NOTE: Support is in English only.
● Customers who are deaf or hard of hearing who have questions about technical support or accessibility of HP products:
– Use TRS/VRS/WebCapTel to call (877) 656-7058 Monday through Friday, 6 a.m. to 9 p.m. Mountain
Time.
● Customers with other disabilities or age-related limitations who have questions about technical support or accessibility of HP products, choose one of the following options:
– Call (888) 259-5707 Monday through Friday, 6 a.m. to 9 p.m. Mountain Time.
– Complete the Contact form for people with disabilities or age-related limitations .
30 Appendix B Accessibility
advertisement