Avaya
Avaya™ M4648ML-T Installation Guide
The Avaya M4648ML-T is a 48 10/100BASE-T port multilayer I/O module for the
Avaya™ P460 switch.
Figure 1 M4648ML-T Front Panel
Safety Information
Caution: The Avaya P460 switch and modules contain components sensitive to electrostatic discharge. Do not touch the circuit boards unless instructed to do so.
Caution: Do not leave any slots open. Use the the blanking plates supplied to cover empty slots.
Caution: Do not insert any objects into the P460 chassis other than specifically designed Avaya products.
Warning: Keep your fingers and other objects clear of the fan module. The fans are on whenever the power is on in the chassis.
Catalog No. DO0726 Rev.0 February 2003 1
Installing the Module in the Avaya P460
L You can install I/O modules in slots 3 to 6 only.
Figure 2 Installing P460 I/O Modules
P460 a b
3
3 a a a a aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa a a a a aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa a a a a aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa a a a a aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa aaaa
Key a Open locking handle b Closed locking handle
1 Open the locking handles at the edge of the front panel.
2 Position the module in the slot with the module name towards the top left-hand side of the module.
3 Gently slide the module in.
L Ensure the hooks on the locking handle are aligned with the matching holes on the chassis.
4 Close the locking handles.
X The module slides back and connects to the backplane.
5 Gently tighten the screws.
2
Removing the Module from the Avaya P460
1 Loosen the screws.
2 Open the locking handles.
X The module is disconnected from the backplane and slides forward.
3 Grasp the handles and pull gently but firmly towards yourself.
4 Insert another module or a blanking plate.
Avaya™ M4648ML-T Installation Guide
Specifications
Standards compliance
IEEE
• IEEE 802.3x Flow Control
• IEEE 802.1q/p VLAN Tagging and 802.1p compatible
• IEEE 802.1D
Spanning Tree protocol
IETF
• MIB-II - RFC 1213
• Bridge MIB for Spanning Tree - RFC 1493
• RMON - RFC 1757
• SMON - RFC 2613
Power requirement
48 W
Interface
48 10/100BASE-T ports (RJ-45)
Ordering information
Product
Avaya M4648ML-T
Material Code
700255029
PEC Code
4545-003
Avaya™ M4648ML-T Installation Guide 3
4 avaya.com
© 2003 Avaya Inc. All rights reserved. All trademarks identified by the ® or TM are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners
Avaya™ M4648ML-T Installation Guide
