HP t820 Flexible Thin Client Guide
广告
广告
HP Easy Shell Administrator Guide
SUMMARY
HP Easy Shell allows you to configure connections, websites, and applications for kiosk-style deployments of HP thin clients based on Windows® operating systems.
Copyright information
© Copyright 2014–2020 HP Development
Company, L.P.
Citrix, ICA, and StoreFront are trademarks of
Citrix Systems, Inc. and/or one more of its subsidiaries, and may be registered in the
United States Patent and Trademark Office and in other countries. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. VMware and Horizon
View are registered trademarks or trademarks of VMware, Inc. in the United States and/or other jurisdictions.
Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and
12.212, Commercial Computer Software,
Computer Software Documentation, and
Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license.
The information contained herein is subject to change without notice. The only warranties for
HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Tenth Edition: October 2020
First Edition: March 2014
Document Part Number: L69884–002
User input syntax key
Text that you must enter into a user interface is indicated by fixed-width font .
Table User input syntax key
Item
Text without brackets or braces
<Text inside angle brackets>
[Text inside square brackets]
{Text inside braces}
|
Description
Items you must type exactly as shown
A placeholder for a value you must provide; omit the brackets
Optional items; omit the brackets
A set of items from which you must choose only one; omit the braces
A separator for items from which you must choose only one; omit the vertical bar
...
Items that can or must repeat; omit the ellipsis iii
Table of contents
iv
1 Getting started
HP Easy Shell allows you to configure connections, websites, and applications for kiosk-style deployments of HP thin clients based on Windows ® operating systems. You can also customize the kiosk interface that is presented to standard users and enable or disable user access to specific Control Panel settings. The configured environment can be deployed to multiple thin clients using HP Device Manager (HPDM).
NOTE: Enabling user access to Control Panel settings might also give the user access to File Explorer.
Many thin client deployments need to provide either a single- or limited-purpose environment to users, such as an environment for web browsing or remote desktop access. HP Easy Shell simplifies this type of thin client deployment by hiding the standard Windows interface, restricting users to certain applications and functions, and locking down the system against user modification.
NOTE:
This guide applies to HP Easy Shell 3.5 or newer (see Obtaining and opening HP Easy Shell on page
for information about obtaining the latest version).
Supported operating systems, connection types, and applications
The following table describes the operating systems, connection types, and applications supported by HP
Easy Shell.
Table 1-1 HP Easy Shell Compatability
Item Description
Operating systems
Connection types
Applications
Windows 10 IoT Enterprise
Windows Embedded 8.1 Industry Pro
Windows Embedded 8 Standard
Windows Embedded Standard 7
Web browser*
Citrix® ICA**, StoreFront**, Web Interface**
Microsoft ® RDP
VMware® Horizon View™ (PCoIP, RDP)
All traditional desktop applications that are supported by the operating systems listed above should work with HP Easy Shell.
HP Easy Shell does not support Windows Store apps.
* HP Easy Shell features a built-in kiosk-style web browser with limited functionality that is suitable for standard web browsing. Alternatively, a web browser connection can be configured to use the full Internet
Explorer browser, if additional functionality is needed.
** Citrix® ICA ® , StoreFront ™
for information on where to create each Citrix connection type.
Getting started 1
Obtaining and opening HP Easy Shell
HP Easy Shell is typically preinstalled on HP thin clients. It can also be downloaded or updated via HP
ThinUpdate.
NOTE: For more information, see the administrator guide for HP ThinUpdate.
HP Easy Shell contains the following two components:
● HP Easy Shell—This is the tile-based, kiosk-style user interface that allows standard users to launch applications, connections, and websites as configured by the administrator.
● HP Easy Shell Configuration—This is the configuration utility used by the administrator to configure the experience for standard users.
Opening HP Easy Shell within Windows
Follow the instructions outlined here to open HP Easy Shell within Windows.
▲ Windows Embedded Standard 7—Select Start, select All Programs, select HP, and then select HP Easy
Shell.
Windows Embedded 8 Standard and Windows Embedded 8.1 Industry Pro—Select HP Easy Shell at the
Start screen.
Windows 10 IoT Enterprise—Type Easy Shell into the taskbar search box, and then select the HP
Easy Shell app.
Opening HP Easy Shell Configuration from outside HP Easy Shell
Follow the instructions outlined here to open HP Easy Shell Configuration from outside HP Easy Shell.
▲ Open Control Panel and select HP Easy Shell Configuration.
NOTE: You will be prompted for administrator credentials if you are logged on to Windows as a standard user.
Opening the Configuration from within HP Easy Shell
Follow the instructions outlined here to open HP Easy Shell Configuration from within HP Easy Shell to make configuration changes without having to log off to the standard user account.
1.
In HP Easy Shell, select Admin.
2.
Use the User Account Control dialog to log on as an administrator.
3.
Configure changes as necessary, and then select Apply.
4.
Select Exit to return to HP Easy Shell.
Using HP Easy Shell
The following information is the typical process for using HP Easy Shell to configure the environment for standard users.
The typical process for using HP Easy Shell to configure the environment for standard users is as follows:
2 Chapter 1 Getting started
1.
Open the HP Easy Shell Configuration utility (see Obtaining and opening HP Easy Shell on page 2 for
more information).
2.
for more information) and be sure to select Apply to apply the configuration.
3.
If you are configuring HP Easy Shell from an administrator account, log off, and then log on as a standard user.
If you are configuring HP Easy Shell from a standard user account and you switched to the configuration utility using the Admin button, select Exit to return to the standard user interface.
NOTE: You can test the user experience from an administrator account, with the exception that the
Kiosk mode setting does not affect administrator accounts.
4.
Be sure that the environment is configured as needed. If it is not, return to HP Easy Shell Configuration to make additional changes.
5.
The configuration can be deployed to other thin clients (see
for more information).
Using HP Easy Shell 3
2 Configuration
This chapter outlines configuration settings for HP Easy Shell.
Creating an HP Easy Shell configuration
The following table describes the settings available in each panel in the HP Easy Shell Configuration utility.
Table 2-1 Configuration options
Panel
Settings
Applications
Connections
StoreFront
Websites
Description
Allows you to do the following:
● Create custom Easy Shell profiles for specific users and domains (see
● Enable kiosk mode, which makes the traditional Windows interface (such as the desktop and taskbar) inaccessible to standard users.
NOTE: This global setting affects all standard user accounts in all Easy Shell profiles.
●
Customize the user interface for an Easy Shell profile (see Customizing the user interface on page 4
for more information).
● Set up a reboot schedule for the thin client.
Allows you to add applications to an Easy Shell profile (see Adding an application on page 7 ).
Allows you to add Citrix ICA, RDP, and VMware connections to an Easy Shell profile (see
Citrix ICA, RDP, or VMware connection on page 8
).
Allows you to add Citrix StoreFront connections to an Easy Shell profile (see
StoreFront connection on page 10 ).
Allows you to add internet, network, and Citrix Web Interface sites and set the default site for an
Easy Shell profile (see Adding an internet, network, or Citrix Web Interface site on page 11 ).
Customizing the user interface
The settings under the User Settings heading let you enable or disable access to specific system settings for standard users. Select the Advanced button for quick access to HP Logon Manager and HP Hotkey Filter.
NOTE: For information about HP Logon Manager, see the administrator guide for your operating system.
For information about HP Hotkey Filter, see the administrator guide for HP Hotkey Filter.
The settings under the Behavior Settings heading let you specify an action to occur when a smart card is removed from the system: Log Off, Restart, or Shut down.
The following table describes the settings under the User Interface heading.
For more customization options, see Customizing through the registry on page 17 .
4 Chapter 2 Configuration
Table 2-2 User interface options
Setting
Display tiles button
Display applications
Display connections
Display StoreFront
Enable StoreFront categories
Display websites
Display browser button
Display address box
Display navigation buttons
Display home button
Display admin button
Display power button
Allow lock
Allow logoff
Allow restart
Allow shutdown
Display virtual keyboard button
Enable legacy touch keyboard
Display time
Description
If set to On, the Tiles button is displayed in the top-right corner of the user interface, allowing users to access the configured applications, connections, and websites.
NOTE: If the Tiles button is disabled, users cannot access the configured applications, connections, or websites. If no applications, connections, or websites are configured, the Tiles button is not displayed even if this setting is enabled.
If set to On, the configured applications are available to users in the Tiles panel of the user interface.
If set to On, the configured Citrix ICA, RDP, and VMware connections are available to users in the
Tiles panel of the user interface.
If set to On, the configured Citrix StoreFront connections are available to users in the Tiles panel of the user interface.
If set to On, the All, Favorites, Apps, and Desktops categories appear.
If set to On, the configured internet, network, and Citrix Web Interface sites are available to users in the Tiles panel of the user interface.
If set to On, the Browser button is displayed in the top-right corner of the user interface, allowing users to access the built-in web browser.
If set to On, the address box for the built-in web browser is displayed in the user interface.
NOTE: The setting does not apply to the full Internet Explorer browser. If the full Internet
Explorer browser is used, the built-in web browser controls are always disabled.
If set to On, the navigation buttons for the built-in web browser is displayed in the user interface.
NOTE: The setting does not apply to the full Internet Explorer browser. If the full Internet
Explorer browser is used, the built-in web browser controls are always disabled.
If set to On, the home button is displayed in the top-left corner of the user interface when using
).
NOTE: The home button is not accessible if the full Internet Explorer browser is full screen but not embedded in the HP Easy Shell user interface.
If set to On, the Admin button is displayed in the top-right corner of the user interface, allowing administrators to access HP Easy Shell Configuration.
If set to On, the power button is displayed in the top-right corner of the user interface, allowing users to select from the available settings.
If set to On, users can lock the computer using the drop-down menu for the power button.
If set to On, users can log off the current user account using the drop-down menu for the power button.
If set to On, users can restart the computer using the drop-down menu for the power button.
If set to On, users can shut down the computer using the drop-down menu for the power button.
If set to On, users can access a virtual keyboard using a button in the top-left corner of the user interface.
NOTE: You can change the Virtual keyboard style through the registry.
If set to On, the touch keyboard is displayed automatically for legacy apps, such as Notepad, that do not trigger the touch keyboard to display.
If set to On, the current time is displayed in the lower-left corner of the user interface.
Customizing the user interface 5
Table 2-2 User interface options (continued)
Setting Description
Display device name and IP address If set to On, the computer name and IP address are displayed in the lower-left corner of the user interface.
Display MAC address If set to On, the MAC (Media Access Control) address for the computer is displayed in the lower-left corner of the user interface.
Enable task switcher If set to On, the task switcher is available in the lower-right corner of the user interface, allowing users to quickly switch between tasks.
NOTE: To enable the HP Write Manager icon to work within task switcher, you must remove
HPWFTray.exe
from startup programs.
▲ The HP Write Manager app can be deleted from startup programs from the registry at:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion
\Run .
Display notification tray
Permanent
Display time
Display battery icon
- or -
Instead of the deleting the entry, you can rename the file to a nonexistent file name. For example, you can change hpwtftray.exe
to hpwtftray123.exe
. This change has the same effect as deleting the entry.
If set to On, a notification tray is displayed on the task switcher.
If set to On, the task switcher is always displayed and is not hidden automatically.
Displays time and date in tray.
If set to On, the battery icon is displayed on the task switcher.
Display cellular signal icon
Display sound icon
Sound icon interaction
NOTE: This icon is always read-only.
If set to On, the cellular signal icon is displayed on the task switcher.
NOTE: This icon is always read-only.
If set to On, the sound icon is displayed on the task switcher.
If set to On, the system volume can be adjusted via the sound icon on the task switcher.
Display Wi-Fi icon
Wi-Fi icon interaction
Display write filter icon
Write filter icon interaction
If set to On, the Wi-Fi icon is displayed on the task switcher.
If set to On, Wi-Fi settings can be accessed via the Wi-Fi icon on the task switcher.
If set to On, the write filter icon is displayed on the task switcher.
If set to On, write filter settings can be accessed through the task switcher.
Enable network status notification If set to On, notifications about network and internet connectivity are displayed.
Hide HP Easy Shell during session If set to On, the HP Easy Shell interface is hidden during an application, connection, or website session.
Enable custom background
Extended background
If set to On, the specified image file is used for the background of the user interface.
If set to On, the background used in HP Easy Shell displays on secondary monitors.
NOTE: To activate this setting, set Enable Custom background to On.
6 Chapter 2 Configuration
Table 2-2 User interface options (continued)
Setting
Select theme
Description
This button opens a dialog box that allows you to customize the color theme for the user interface.
NOTE: Select Apply to apply the changes and add the settings to the registry. For information on exporting
.
Display settings
To manage monitor shortcut settings, use the keyboard shortcut Win+P.
● PC Screen Only—Allows for only one display on the main monitor of desktop thin clients, and the embedded monitor on laptops.
● Duplicate—Duplicates the image on the main display to all other displays.
● Extend—Other displays are an extension of the main display.
● Second screen only—Only the secondary displays are on.
Adding an application
Follow the instructions outlined here to add an application.
1.
In the Applications panel, select the Application tile.
2.
Configure settings in the application editor as necessary.
NOTE: See the following table for a list of settings.
3.
Select OK to finish adding the application.
4.
Select Apply to save your changes.
You can edit or delete an application by selecting the corresponding button on that application tile.
The following table describes the settings available in the application editor.
Table 2-3 Application editor settings
Setting
Name
Path
Arguments
Launch delay
Custom icon
Exit action
Description
Specifies a custom name to be displayed on the tile for the application.
Specifies the full file path to one of the following file types: .exe, .com, .bat, .cmd, or .cpl.
Allows you to specify command-line arguments.
Sets the delay, in seconds, for an auto-launched application.
Allows you to set a custom icon (.exe, .png, .jpg, .bmp, or .ico) for the application.
Sets the action to take when the application is closed (None, Log off, Restart, Shut down).
Display settings 7
Table 2-3 Application editor settings (continued)
Setting
Auto-launch
Maximized
Persistent
Admin only
No tracking
Hide missing app
Wait for network
Wait for Internet
Description
When enabled, the application launches automatically when the user logs on to
Windows.
When enabled, the application maximizes automatically when opened.
When enabled, the application reopens automatically when closed.
NOTE: This setting can be set only if Exit action is set to None.
When enabled, the application is available only for administrators.
When set to Off, apps are tracked and a green indicator informs the user that the app is active. When set to On, apps are no longer tracked and there is no green indicator on the app tile. When set to On, it is possible to have multiple instances of a single app running at the same time.
When enabled, if HP Easy Shell cannot find the executable file at the indicated path, the app tile is hidden from users.
When enabled, the application does not auto-launch until a network connection is found. A screen with the message Waiting for connectivity is displayed while the network connection is searched for.
NOTE: This setting can be set only if Auto-launch is set to On.
When enabled, the application does not auto-launch until an internet connection is found. A screen with the message Waiting for connectivity is displayed while the internet connection is searched for.
NOTE: This setting can be set only if Auto-launch and Wait for network are set to On.
Adding a Citrix ICA, RDP, or VMware connection
Follow the instructions outlined here to add a Citrix ICA, RDR, or VMware connection.
Adding a Citrix ICA, RDP, or VMware connection
Follow the instructions outlined here to add a Citrix ICA, RDR, or VMware connection.
1.
In the Connections panel, select the tile for the connection type that you want to add.
2.
Configure settings in the connection editor as necessary.
NOTE:
. For information about other advanced connection settings that vary by connection type, see the documentation provided by Citrix, Microsoft, or VMware.
3.
Select OK to finish adding the connection.
4.
Select Apply to save your changes.
Assigning a failover connection to a profile
Follow the instructions outlined here to assign a failover connection to a profile:
8 Chapter 2 Configuration
1.
In the Connections panel, select the connection profile, and then drag it onto one of your previously created connections.
2.
Select Apply to save your changes.
NOTE: A failover connnection inherits the primary connection's settings for the Exit action, Persistent, and
Auto-launch settings if the primary connection was launched. If the failover connection was launched manually, it follows its own settings for those settings.
Common connection settings
The following table describes some of the connection settings that are common to the Citrix ICA, RDP, and
VMware connection editors.
Table 2-4 Connection settings
Setting
Connection name
Hostname
Exit action
Launch delay
Arguments
Auto-launch
Persistent
Wait for network
Wait for Internet
Description
Specifies a custom name to be displayed on the tile for the connection.
Specifies the host name or IP address for the connection.
Sets the action to take when the connection is ended (None, Log off, Restart, Shut down).
Sets the delay, in seconds, for an auto-launched application.
Allows you to specify command-line arguments.
When enabled, the connection launches automatically when the user logs on to Windows.
When enabled, the connection reconnects automatically when ended.
NOTE: This setting can be set only if Exit action is set to None.
When enabled, the connection does not auto-launch until a network connection is found. A screen with the message Waiting for connectivity is displayed while the network connection is searched for.
NOTE: This setting can be set only if Auto-launch is set to On.
When enabled, the connection does not auto-launch until an internet connection is found. A screen with the message Waiting for connectivity is displayed while the internet connection is searched for.
NOTE: This setting can be set only if Auto-launch and Wait for network are set to On.
RDP file customization
Adding custom values
HP Easy Shell automatically generates the RDP file for the RDP connections that you create. To add custom values to the RDP file, use the Expert tab in the RDP connection editor. The value type can be s (string), i
(integer), or b (byte).
Using a custom RDP file
Follow the instructions outlined here to use a custom RDP file.
1.
On the Basic tab in the RDP connection editor, enable the Custom RDP file option.
Common connection settings 9
2.
Specify the RDP file path.
Adding a Citrix StoreFront connection
Follow the instructions outlined here to add a Citrix StoreFront connection.
NOTE: On the devices that connect to the StoreFront server, you must install the SSL certificates for your
StoreFront server. If no certificates exist, HP Easy Shell might fail to communicate with the server.
1.
In the StoreFront panel, select the StoreFront tile.
2.
Select the Select store button to use the wizard.
– or –
Enter the full path for the StoreFront URL in the Store URL box in a format similar to: https:// samplestorefrontaddress.net/citrix/thinclient . Then, go to step 6.
TIP: If you do not include http:// or https:// in the URL, it defaults to https://.
3.
Enter the base path for the StoreFront URL. A base path should be entered in a format similar to the following: https://samplestorefrontaddress.net
. Then, select Next.
TIP: If you do not include http:// or https:// in the URL, it defaults to https://.
4.
If prompted, enter the StoreFront Citrix credentials, and then select OK.
5.
Select the StoreFront account, and then select Next.
6.
Configure the settings in the connection editor as necessary.
NOTE: See the following table for a list of settings.
7.
Select Save to finish adding the connection.
8.
Select Apply to save your changes.
NOTE: NetScaler is supported as well. HP Easy Shell supports updating StoreFront and NetScaler passwords after they have expired.
The following information about StoreFront connections might be helpful:
● You can edit or delete a connection by selecting the corresponding button on that connection tile.
● At the bottom of the StoreFront panel, you can set the action to take when all StoreFront connections have ended.
● When a StoreFront session is active, you can select Disconnect session under the resource window to end the session.
The following table describes the settings available in the StoreFront connection editor.
Table 2-5 Citrix StoreFront connection settings
Panel Setting Description
StoreFront Connection name Specifies a custom name to be displayed on the tile for the connection.
10 Chapter 2 Configuration
Table 2-5 Citrix StoreFront connection settings (continued)
Panel
StoreFront
StoreFront
StoreFront
StoreFront
StoreFront
StoreFront
StoreFront
StoreFront
StoreFront
Options
Options
Options
Behaviors
Behaviors
Setting
Store URL
Launch delay
Exit action
Logon method
Domain
Enable auto-logon
Custom logo
Auto-launch
Session timeout
Desktop Viewer toolbar
Disable resource interactivity
Resource title
Wait for network
Wait for internet
Description
Specifies the StoreFront URL.
Sets the delay, in seconds, for an auto-launched application.
Sets the action to take when the connection is ended (None, Log off, Restart, Shut down).
Allows you to select Username and password, Smart card, or Single sign-on.
IMPORTANT: By default, single sign-on is not enabled for Citrix Receiver on HP thin clients. For information about how to enable single-sign on for Citrix Receiver, see the administrator guide for your HP thin client operating system.
Allows you to hide the domain from users.
When enabled, HP Easy Shell automatically logs on to the StoreFront connection when the user logs on to Windows.
NOTE: This setting is available only if the logon method is set to Username and password.
Allows you to enter a custom logo (.exe, .png, .jpg, .bmp, or .ico) to show on the logon window for StoreFront.
When enabled, the connection launches automatically when the user logs on to
Windows.
Specifies in d.hh.mm.ss format the amount of time that the StoreFront session remains open. After the session timeout is reached, the connection automatically closes.
NOTE: If you need the session timeout to be greater than 1 hour, see the StoreFront documentation. You must change the appropriate web.config file’s lifetime token values for the auth store, because the Citrix default setting is 1 hour. For example, edit maxLifetime values in
C:\intetpub\wwwroot\Citrix\Name_of_StoreAUTH\web.config
to the appropriate value.
When enabled, the Citrix Desktop Viewer toolbar is displayed during published desktop sessions for the StoreFront.
When enabled, auto-launch resources start, but the user cannot interact with
StoreFront resources.
Allows you to set a specific StoreFront resource to launch automatically when the connection starts.
When enabled, the StoreFront connection does not auto-launch until a network connection is found. A screen with the message Waiting for connectivity is displayed while the network connection is searched for.
NOTE: You can set this setting only if Auto-launch is set to On.
When enabled, the StoreFront connection does not auto-launch until an internet connection is found. A screen with the message Waiting for connectivity is displayed while the internet connection is searched for.
NOTE: You can set this setting only if Auto-launch and Wait for network are set to
On.
Adding an internet, network, or Citrix Web Interface site
This section outlines how to configure and add internet, network and Citrix Web Interface settings.
Adding an internet, network, or Citrix Web Interface site 11
1.
In the Websites panel, select the Website tile.
2.
Configure settings in the website editor as necessary.
NOTE: See the following table for a list of settings.
3.
Select OK to finish adding the website.
4.
Select Apply to save your changes.
A website can be set as the home site (the default site, which is automatically launched when the program starts), edited, or deleted by selecting the corresponding button on that website tile.
The following table describes the settings available in the website editor.
NOTE: Single sign-on is not supported for Citrix Web Interface connections.
Table 2-6 Citrix Web Interface settings
Setting
Name
Address
Use Internet Explorer
Full-screen Internet Explorer
Embed Internet Explorer
Allow closing embedded Internet Explorer
Wait for network
Wait for Internet
Custom icon
Description
Specifies a custom name to be displayed on the tile for the connection.
Specifies the website address.
When enabled, the website is opened in Internet Explorer. Otherwise, the website is opened within the Easy Shell interface.
IMPORTANT: This setting must be enabled for a Citrix Web Interface connection.
When enabled, Internet Explorer opens in full screen, which makes the Internet Explorer address bar and navigation buttons inaccessible. If Embed Internet Explorer is disabled, this also hides the entire HP Easy Shell user interface, except for the task switcher.
NOTE: This setting can be enabled only if Use Internet Explorer is enabled.
When enabled, the full-screen Internet Explorer is embedded in the HP Easy Shell user interface. The controls at the top of the interface can be accessed in this configuration, but the Internet Explorer address bar and navigation buttons are still inaccessible.
NOTE: This setting can be enabled only if Full-screen Internet Explorer is enabled.
When enabled, the embedded Internet Explorer can be closed.
When enabled, the web browser does not auto-launch until a network connection is found. A screen with the message Waiting for connectivity is displayed while the network connection is searched for.
NOTE: This setting affects only the home site.
When enabled, the web browser does not auto-launch until an internet connection is found. A screen with the message Waiting for connectivity is displayed while the internet connection is searched for.
NOTE: This setting can be set only if Wait for network is set to On and affects only the home site.
Allows you to set a custom icon (.exe, .png, .jpg, .bmp, or .ico) for the application.
Adding a custom Easy Shell profile
Follow the instructions outlined here to add a custom Easy Shell profile.
12 Chapter 2 Configuration
In most deployments, using only the default Easy Shell profile will suffice. However, you can create custom
Easy Shell profiles, if you need to assign different settings to different users and domains. The default profile is used for any users or domains not specifically assigned to a custom Easy Shell profile.
To add a custom Easy Shell profile:
1.
In the Settings panel, select the profile tile under Global Settings.
2.
Type a name for the profile, and then select Add.
3.
Choose to add either a user or a domain by selecting the corresponding option.
NOTE: User accounts cannot be added to the default profile. That profile is used automatically for all user accounts not assigned to a custom profile.
4.
Type the user name or domain name, and then select Add.
5.
Optionally, add additional users and domains.
6.
Select Done.
7.
Select Apply to save your changes.
You can rename or delete an Easy Shell profile by selecting the corresponding button on the profile tile.
Adding a custom Easy Shell profile 13
3 Deployment
This chapter discusses the various methods that can deploy HP Easy Shell to multiple thin clients. The best method depends on your use case and environment.
NOTE: All of the following methods discuss using HPDM for deployment. For more specifics on HPDM, see the HP Device Manager Administrator Guide.
Deploying a preconfigured thin client image
You can deploy HP Easy Shell by configuring it on a thin client image that will be captured and deployed to other thin clients. The most efficient way to deploy an image to multiple thin clients is via HPDM, which has preset templates for capturing and deploying an image.
Deploying HP Easy Shell to existing thin client images
Follow the instructions outlined here to deploy HP Easy Shell to existing thin client images.
1.
Configure HP Easy Shell on a single system, and then export the configuration as a registry file, as described in
Exporting and deploying an HP Easy Shell configuration on page 14 .
2.
Copy the registry file to the system running the HPDM Console.
3.
Use the HP FTP Software Component Browser to locate the HP Easy Shell package on the HP FTP site, and then generate a _File and Registry template for the package.
4.
Add a subtask to the template and import the registry file containing the exported configuration.
5.
Deploy the template to the target thin clients.
Exporting and deploying an HP Easy Shell configuration
This section outlines how to export an HP Easy Shell configuration to a registry file.
You can export an HP Easy Shell configuration as a Windows registry file so that it can easily be deployed to other thin clients.
NOTE: Be sure that HP Easy Shell is being deployed simultaneously or is already installed on each thin client.
1.
Click the Export button in the lower-left corner of the HP Easy Shell Configuration utility.
2.
Select the destination folder, and then enter a name for the configuration.
3.
Click Save.
NOTE: An HP Easy Shell configuration can also be exported to a registry file by entering the following in an administrator command prompt (be sure to include the double quotes around the file path if it contains spaces):
14 Chapter 3 Deployment
hpeasyshell.exe /export "<registry file>.reg"
You can import the registry file into a _File and Registry template in HPDM. The template can then be used to deploy the configuration to the target thin clients.
You can also deploy the exported registry file to other thin clients in either of the following ways:
● Copy the registry file to another thin client, and then double-click the registry file to apply the settings.
● Use Group Policy to propagate the registry settings to certain domain users.
Exporting and deploying an HP Easy Shell configuration 15
4 Tips and best practices
Consider the information outlined here when using HP Easy Shell.
● Some applications might require a launch delay to function properly.
● When setting Internet Explorer as an auto-started application, be sure to launch the version that best matches the operating system (32-bit or 64-bit); otherwise, the end-of-session action might not be triggered.
● HP Easy Shell does not filter the built-in web browser content. Keep this in mind when selecting the websites. The web browser can be further locked down using the following:
– Group Policy
–
Internet Explorer registry restrictions (see Internet Explorer registry restrictions on page 18 for
more information)
If the web browser is intended to be used for intranet only, it is best to disable the address bar and add links to the Sites menu.
● The desktop resolution settings available in the ICA and RDP connection editors are not indicative of the target monitor. It is best to use the default setting (full-screen).
● For RDP connections, it is best to disable the RDP connection bar setting in the Display panel of the connection editor when deploying in kiosk mode. This setting is enabled by default, and the connection bar could be used by users to access the local desktop.
● To use USB redirection with an RDP connection when the VMware Horizon View client is installed, you must first disable the VMware Horizon View USB service before connecting to an RDP session.
● If you log on to an administrator account while User Account Control is enabled (in Windows) and kiosk mode is enabled (in HP Easy Shell), you will be presented with a User Account Control dialog asking for permission to make changes to the computer. If you select No, Windows will not allow HP Easy Shell to become a shell replacement and will be stuck at the logon process. Use ctrl+alt+del to log off the account if this happens. You must select Yes at the User Account Control dialog to successfully complete the logon process.
16 Chapter 4 Tips and best practices
A Customizing through the registry
You can further customize the behavior and settings of HP Easy Shell through the registry.
Display user name
Follow the instuctions outlined here to display the user name of the user.
To display the user name of the user:
▲ In the registry, create the following string key-value:
HKEY_LOCAL_MACHINE\SOFTWARE\HP\HP Easy Shell\UI .
DisplayUsername=True
Customizing title category names
Categories can be renamed through the registry. You must create a string key-value DisplayName .
To change category names, modify the following registry keys:
● [HKEY_LOCAL_MACHINE\SOFTWARE\HP\HP Easy Shell\Apps]
DisplayName=Applications
● [HKEY_LOCAL_MACHINE/SOFTWARE\HP\HP Easy Shell\Connections]
DisplayName=Connections
● [HKEY_LOCAL_MACHINE\SOFTWARE\HP\HP Easy Shell\StoreFront]
DisplayName=StoreFront
● [HKEY_LOCAL_MACHINE\SOFTWARE\HP\HP Easy Shell\Sites]
DisplayName=Websites
Delay Easy Shell start up
You can create a string key-value to delay the start up of HP Easy Shell. HP recommends a delay of 5 seconds to resolve errors that might occur when some apps start in kiosk mode.
[HKEY_LOCAL_MACHINE\SOFTWARE\HP\HP Easy Shell]
DelayStart=5
Virtual keyboard style
Virtual keyboard style can be changed through the registry by creating a string key-value.
[HKEY_LOCAL_MACHINE\SOFTWARE\HP\HP Easy Shell]
VirtualKeyboardStyle=1
Customizing through the registry 17
Accepted values are 0 or 1.
Delay browser embed
If the embedded browser window does not resize properly, create the following string key-value to delay the browser window embedding.
[HKEY_LOCAL_MACHINE\SOFTWARE\HP\HP Easy Shell\Sites]
EmbedDelay=2
Accepted value: 2 or higher.
By default, the value is 2. Increase the value to delay the embedding.
Creating custom connection error messages
Follow the instructions outlined here to create custom connection error messages.
Administrators can create custom error messages for when a connection fails.
▲ The registry key HKEY_LOCAL_MACHINE\SOFTWARE\HP\HP Easy Shell\protocols contains subkeys for the default connection protocols: CitrixICA , RDP , and VMware . With the subkey specified, create a string key-value with the name ErrorMessage . For the data, enter the text you want to display.
For example, to create a custom error message for RDP:
HKEY_LOCAL_MACHINE\SOFTWARE\HP\HP Easy Shell\protocols\RDP
ErrorMessage=Please contact your administrator.
Internet Explorer registry restrictions
Modify the following registry key to restrict the built-in web browser and the full Internet Explorer browser.
HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Internet
Explorer\Restrictions
The following table describes the registry settings that apply to HP Easy Shell:
Table A-1 Registry settings
Registry entry
NoSelectDownloadDir
NoBrowserContextMenu
NoViewSource
NoOpeninNewWnd
NoPrinting
Description
Disables the Save command in the File Download dialog box.
Disables the right-click context menu in the browser.
Disables the View Source command in the right-click context menu.
Disables the Open in New Window command in the right-click context menu.
IMPORTANT: Links that are coded to open a new window will still do so.
Disables the Print command.
18 Appendix A Customizing through the registry
文档公共链接
广告