ADAX NEO S5.1
User Guide
Control Panel
Menu Functions
Press and hold OK for 5 seconds to open and close the menu. td
Pr
Co rd
OP
Setting the time and day
The weekly program menu
“Comfort” temperature
“Reduced” temperature
Open window detection function
C
AS
Temperature calibration
Adaptive start function rE Reset the heater to factory default settings
Use “>” button to cycle through list
“OK” Confirms selection and opens functions menu button
“+” Increases temperature, increases other parameters
“ ” Decreases temperature, reduces other parameters
“>” Selection button more
(Used to scroll though lists)
“>” Selection button less
(Used to scroll though lists)
Green light at top.
Red “heating light”
Indicates that the heater is calling for heat.
1.
Initial Set Up.
Indicates that the heater is in comfort mode.
Green light at bottom.
Indicates that the heater is in reduced mode.
When the heater is switched on for the first time, it begins operating at the default “comfort” temperature of 22°C. This is the home screen.
The screen will blink indicating that the time and day has not been set.
2.
Pre-Set programmes.
The heater has 3 programme modes: “Office” (P2) “Home” (P3) and P1( the user’s programme ).
See section 4 for details on how to set P1 . The heater will operate at the default temperature settings comfort = 22°C, reduced = 17°C).
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
(Times of “comfort” temperature)
P1
User Programmed
User Programmed
User Programmed
User Programmed
User Programmed
User Programmed
User Programmed
P2
07-17
07-17
07-17
07-17
07-17
OFF
OFF
P3
06-08, 15-23
06-08, 15-23
06-08, 15-23
06-08, 15-23
06-08, 15-23
07-23
07-23
3.
Setting the time and day.
Start from the Below home
Screen :
Hold the OK button until Td is present Press OK To enter the day menu
1.
Select the current day of the week using + and – . hours (eg 1 -Monday, 2 Tuesday ect) Press
OK to confirm and move on to setting the hours
2.
Set the current hour; press OK once to confirm
3.
Set the minutes; press OK once confirm
4.
Td will show on the display
The and time access
and day
the functions . must be set before you can programmes
5.
Hold OK to return to the home screen
4.
Setting the heater’s timer .
Start at the home screen, as shown below.
Press and Hold OK until the menu is opened.
Hold OK
Set the minutes; press OK once confirm
Press OK
Press the > button until Pr is displayed.
Press
OK
7d Programme Monday - Sunday
5d Programme Monday - Friday
2d Programme Saturday – Sunday d1 Monday d2 Tuesday d3 Wednesday d4 Thursday d5 Friday d6 Saturday d7 Sunday
Then press Ok to confirm
Press >
Now select which days you wish to programme
Press OK
Press OK to Select P1
The Time programmer will now be open.
0 indicates midnight
Using the + or – select either comfort or reduced mode
Pressing the + button will set the heater to “comfort” mode .
Indicated by a green light at the top
Use the > button to progress onto the next hour.
Pressing the - button will set the heater to “reduced” mode.
Indicated by a green light at the bottom
Continue through each hour using +/- and > until you arrive back at 0.
Make sure each hour is programmed to comfort or reduced.
Then press OK once to return to the programme day screen.
Hold OK until you return to the initial home screen.
5.
Setting comfort and reduced mode
Start at the home screen, as shown below.
Press OK once; a number is displayed. Use + or – to change the comfort temp
Press and Hold OK until the menu is opened.
Press the > button until Co is displayed.
Press OK once; a number is displayed. Use + or – to change the reduced temp. Then press
OK to return to the menu
Press OK once return to the menu screen below screen.
Then press > once. RD will display
Then, press and hold OK to return to the home screen.
To activate the programme, select P1
See section 6 on how to activate the timer
6.
Changing / Activating programme mode
Start at the home screen, as shown below.
Press the “>” button to open the menu list
Keep pressing the > button until the desired programme is displayed.
Press OK to confirm your selection.
See the key below for details
See below key.
Option
P1
P2
P3
OF nP
Description
The user's own program. See section 5 to set
Pre set programme 2 “Office”
Pre set programme 3 “Home”
Heater is OFF but the clock setting are maintained.
No programme / manual mode
To indicate that the heater is in a programmed mode ( P1, 2 or 3) a green light will display.
