START HERE
QUICK START
1 Carefully unpack box.
GUIDE
2 Remove screws and cover of unit for access to internal components.
1 of 4 r
Model 25-C1
IMPORTANT!
We recommend mounting Ascent C1 inside the gate operator or other weatherproof enclosure when possible.
If mounting inside a metal enclosure, the
Ascent 10' Cable Extension ( p/n 16-X-EXT ) is required. Follow the instructions included with the cable extension before moving on.
Failure to do so may result in no signal!
Continued on next page...
What’s what?
All the important components labeled for you
SIM Card
If you have your own SIM card, see page 4 and follow the instructions entitled,
Installing a Third-Party SIM Card .
Connection Terminals
For wiring to all external devices including gate operator or door opener
Cable Gland
For sealing cable pass-through
Power Terminals
For wiring to compatible AC/DC power source
Unit shown with cover removed.
Internal wiring not shown for clarity.
r
IMPORTANT!
Ascent WILL NOT WORK until the activation process is COMPLETE !
Follow the Activation Guide or call
Summit Control at (844) 259-8265 to activate your unit.
WARNING!
AUTOMATIC GATES CAN CAUSE
SERIOUS INJURY OR DEATH!
ALWAYS CHECK that the GATE PATH IS
CLEAR BEFORE OPERATING !
Reversing or other safety devices should
ALWAYS BE USED !
3
Connect wires
Feed wires through back of unit and connect as shown.
Ascent
Power
Terminals
12–24 VAC/DC
POWER
J3
QUICK START GUIDE
Ascent Connection Terminals
STATUS DIGITAL INPUTS EVENT RELAY B RELAY A
J7 J8 J9 J6 J5 J4
2 of 4
Model 25-C1
Gate Operator / Door Opener
12–24 VAC/DC
POWER
Additional wiring diagrams can be found on Page 3 .
Relay B can be wired to a second device in the same manner.
+ –
Third-Party 12–24-VAC/DC
Power Source
OR
STOP!
Before going forward, double check wiring and ensure unit has power!
For additional wiring options, see Page 3 .
© 2017 Security Brands, Inc. All rights reserved.
4
12-V AC/DC Adapter
Model PS-12DC1
The GROUND terminal is optional unless required by local code(s). If using, please connect to earth ground or equivalent.
Tighten cable-gland locknut.
5 Replace and secure front cover with included screws.
CAUTION!
If you will not be using the 12-V AC/DC adapter, please go to Page 4 and follow the procedure,
Using a Third-Party Power Source .
Do not exceed 24 VAC/DC! Failure to choose a compatible power source can damage unit!
N
INSTALLATION COMPLETE!
Now follow the Activation Guide to create an account and begin using Ascent.
QSG-25C1-EN Rev. D (9/2017)
QUICK START GUIDE
A
Status Check
Wiring to enable Gate Status Check
B
Event Input
Wiring for accessories such as a request-to-exit device
Ascent Connection Terminals
STATUS DIGITAL INPUTS EVENT RELAY B RELAY A
J7 J8 J9 J6 J5 J4
Ascent Connection Terminals
STATUS DIGITAL INPUTS EVENT RELAY B RELAY A
J7 J8 J9 J6 J5 J4
3 of 4
Model 25-C1
Connected as shown in Step 3
Connected as shown in Step 3
Optional wire splices
Gate Operator
N/C
N/O
COM
N/C
N/O
COM
Close Limit Switch
Open Limit Switch
(if equipped with limit switches)
Request-to-Exit
( Summit Access Control S-RTE-P is shown)
Using a
Third-Party
Power Source
(Optional)
QUICK START r
IMPORTANT!
If you would like to use a third-party power source, such as solar, verify that it conforms to the following specs:
Input
Current Draw
12–24 VAC/DC no more than 10% beyond this range less than 90 mA @ 12 VDC less than 60 mA @ 24 VDC
3a
GUIDE
Connect wires to unit as shown in
Step 3.
3b Connect wires to your power source, making sure you connect positive to positive and negative to negative.
4 of 4
Model 25-C1
CAUTION!
Double check that you’ve wired from positive on Ascent to positive on your power source and negative on Ascent to negative on your power source.
Reverse polarity can damage Ascent!
1 Push existing SIM card in until it unlocks with “click” sound.
2 Remove existing SIM card and locate new SIM card.
3 Insert new SIM card until it locks in place with “click” sound.
Installing a
Third-Party
SIM Card
(Optional)
?
NEED HELP
Call (844) 259-8265
Text (720) 386-4627
Email [email protected]
We are available Mon–Fri / 8am–5pm Central
© 2017 Security Brands, Inc. All rights reserved.
QSG-25C1-EN Rev. D (9/2017)
