PRINTER’S INSTRUCTIONS:
INSTR,INSTL,SW-ATT-GDC - LINEAR P/N: 235667 X14 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
Garage Door Controller
Product Description
The Garage Door Controller (GDC) is designed to work with your existing garage door opener. The GDC will give you remote access to open and close your garage door when used with Digital Life Service. A garage door opener connected to the GDC can be remotely activated using the Digital
Life Web interface or via mobile devices that communicate with the system.
Installation Instructions
WARNING
This operator system is equipped with an unattended operation feature. This door could move unexpectedly.
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors only (per UL-325).
WARNING
The GDC must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.
WARNING
GDC is to be installed only on garage door openers manufactured after 1992 (models with an operational safety beam entrapment protection system, per UL-325).
Figure 1. Garage Door Controller and Garage Door Sensor
The GDC connects to the garage door opener’s pushbutton terminals and communicates with the Digital Life Control Panel (DLC) using 915 MHz radio signals. A wireless garage door sensor mounts on the garage door and reports the door’s position to the GDC. When the GDC receives a command from the DLC, the GDC will open or close the garage door.
Anytime the garage door opener is activated remotely via the Digital Life
System, a warning indicator fl ashes and a beeper sounds for fi ve seconds before the door begins to move.
If, due to an obstruction or other cause, the door does not completely open or close when it is activated remotely, the GDC will pause for 30 seconds. After the delay, a second remote activation can be attempted.
If the door does not complete its motion on the second attempt, the GDC will lock-out and suspend operation. The GDC will report the lock-out condition to the DLC.
Once the garage door is operated by a garage door remote or locally by pushing the opener’s wall station button, the DLC will be reset to allow remote access.
The GDC is powered by a plug-in power supply. The garage door sensor is powered by a 2032 lithium battery. If the garage door sensor battery is low, or the case has been opened, it will be reported to the DLC by the
GDC.
A discovery button and status light are provided on the GDC for adding or removing the device with the DLC.
Four screws and anchors are provided for mounting the GDC. An adjustable GDC mounting bracket with hardware is supplied for installing the unit onto the door opener’s hanging hardware. The wireless garage door sensor mounts with the two screws supplied.
STATUS
I N DICATOR
GARAGE DOOR
CONTROLLER (GDC)
PO W ER
I N PUT
JACK
W AR N I N G
LIGHT
DISCOVERY
BUTTO N
GARAGE DOOR
SENSOR
Discovering and Registering the GDC
1. Place the Digital Life Control Panel into Discovery Mode.
2. Plug the GDC power supply into a 115 VAC outlet.
3. Put the GDC into discovery mode by pressing the Discovery Button.
4. Confi rm that the GDC has been discovered.
PO W ER
SUPPLY
STATUS INDICATOR
✴
BLINKS SLOWLY WHILE IN DISCOVERY MODE
✴
LIGHTS FOR 15 SECONDS FOR DISCOVERY SUCCESS
✴
FLASHES FOR 15 SECONDS IF DISCOVERY FAILS
PO W ER
I N PUT
JACK
GARAGE DOOR
CO N TROLLER
(GDC)
DISCOVERY
BUTTO N
W ALL
OUTLET
Figure 3. Discovering the GDC
Garage Door Sensor Battery
To activate the garage door sensor, remove the battery protection pull strip.
When the system indicates the garage door sensor battery is low, open the garage door sensor case as shown and replace the old 2032 battery with a new one. Install the battery, plus side up.
W HE N THE BATTERY IS LO W
REPLACE THE BATTERY W ITH
A TYPE CR2032 COI N CELL
GARAGE
DOOR
SENSOR
CR2032
PLUS
SIDE
UP !!!
OPE N ER
PUSHBUTTO N
W IRES
POWER
SUPPLY
RETAINING
BRACKET
MOU N TI N G SCRE W S
A N D A N CHORS
POWER
SUPPLY
TO OPE N THE CASE, T W IST
A SMALL SCRE W DRIVER
I N THE CASE SLOT
SLOT
ADJUSTABLE
MOUNTING
BRACKET
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION:
THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS
PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR.
DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.
Figure 2. Product Features Figure 4. Garage Door Sensor Battery
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,SW-ATT-GDC - LINEAR P/N: 235667 X14 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2
"UP"
INDICATOR
Garage Door Controller
Garage Door Sensor Installation
The garage door sensor installs on the top panel of the garage door.
1. Use the garage door sensor mounting plate as a guide to mark the mounting holes.
2. Drill two 1/16” pilot holes if necessary.
3. Attach the mounting plate with the two screws provided. Be sure the post on the mounting plate is on the bottom.
4. Snap the garage door sensor onto the mounting plate. Be sure the arrow on the side of the garage door sensor case is up.
ATTACH MOUNTING PLATE
TO TOP PANEL OF THE DOOR
SNAP SENSOR ONTO
THE MOUNTING PLATE
WITH THE ARROW ON
THE SIDE POINTING UP
Installation Instructions
GDC Connections
The GDC connects to the opener’s pushbutton terminals.
✓ NOTE: Do not disconnect any wires currently connected to the garage door opener.
1. Connect the GDC wires to the pushbutton terminals on the garage door opener. Either wire can connect to either terminal.
2. Remove the power outlet wall plate’s center screw (or one end screw on the decorator style wall plate). Align the power supply retaining bracket with the wall plate so one of the holes in the bracket aligns with a screw hole in the wall plate (be sure the clamps of the bracket are centered over one plug and the other plug is clear). Attach the bracket and wall plate to the outlet using the fl at head machine screw provided with the bracket.
3. Plug the power supply into the 115 VAC power outlet by snapping it into the retaining bracket.
POST ON
BOTTOM
USE THE MOUNTING SCREWS SUPPLIED
(DRILL 1/16" PILOT HOLES IF REQUIRED)
Figure 5. Garage Door Sensor Installation
GDC Installation
The GDC typically mounts on the ceiling near the garage door opener and power outlet. Alternately, the GDC can be mounted to other structures with the adjustable mounting bracket supplied (shown in Figure 2).
✓
NOTE: The GDC’s warning lamp must be visible in all door positions.
Use the four screws and anchors to mount the GDC. -OR- Use the adjustable mounting bracket to mount the GDC.
GARAGE DOOR SE N SOR
MOU N TED O N THE TOP
PA N EL OF THE DOOR
THE GDC TYPICALLY
MOUNTS ON THE CEILING
NEAR THE OPENER AND
THE POWER OUTLET
3/16" HOLES
FOR A N CHORS
THE GDC CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
THE OPTIO
MOU N TI N
N AL ADJUSTABLE
G BRACKET FITS
3 W AYS O N THE GDC
SECURE
BRACKET
W ITH SCRE W
I N DE N T
I N DE N T
THE BRACKET S N APS O N TO
I N DE N TS O N EITHER SIDE OR
O N THE E N D OF THE GDC
USE THE BOLTS A N D N UTS
SUPPLIED TO ATTACH THE BRACKET
TO A SECURE STRUCTURE
I N DE N T
BE SURE THE GDC IS CLEAR
OF ALL MOVING PARTS OF
THE GARAGE DOOR
Figure 6. GDC Installation
Copyright © 2014 Linear LLC
USE THE FOUR SCRE W S
A N D A N CHORS TO MOU N T
THE GDC ABOVE THE OPE N ER
THE GDC'S WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
1
PUSHBUTTO N
W IRES FROM
THE GDC
CO NN ECT THE GDC W IRES
TO THE PUSHBUTTON
A N D COMMON TERMI N ALS
O N THE GARAGE DOOR OPE N ER
EITHER W IRE
CA N CO NN ECT
TO EITHER
TERMI N AL
GARAGE
DOOR
OPENER
2
ATTACH THE RETAI N I N G
BRACKET TO THE 115 VAC
OUTLET A N D S N AP I N THE
PO W ER SUPPLY
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
BE SURE WIRES ARE
CLEAR OF ALL MOVING
PARTS OF THE GARAGE
DOOR AND OPENER
TERMI N AL
LOCATIO N S
VARY PER
MODEL COMMON
PUSHBUTTON
Figure 7. GDC Connections
Specifi cations—GDC
• Model: SW-ATT-GDC
• Compatible panels: DLC-100 Digital Life Control Panel
• Operating Temperature: -31° to 158° F (-35° to 70° C)
• Operating Rel. Humidity: 5 to 95%, non-condensing
• Garage Door Sensor Operating Frequency: 433.92 MHz
• GDC Operating Frequency: 915 MHz
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
changes modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
This device complies with FCC Rules and Regulations as Part 15 devices as well as Industry Canada license exempt RSS Rules and Regulations. Operation is subject to the following two (2) conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. Ľ exploitation est autorisée aux deux conditions suivantes: (1) ľ appareil ne doit pas produire de brouillage, et (2) ľ utilisateur de ľ appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible ď en compromettre le fonctionnement.
Z-Wave is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
235667 X14
