AEG DSE 220 Instructions For Use

Add to My manuals
4 Pages

advertisement

AEG DSE 220 Instructions For Use | Manualzz

DSE 220, DSE 260

Instruction for use

Please read and save these instruction

Gebrauchsanleitung

Bitte lesen und aufbewahren

Instruction d’utilisation

Prière de lire et de conserver

Istruzioni d’uso

Si prega di leggere le istruzioni e di conservarle

Instrucciones de uso

Lea y conserve estas instricciones por favor

Instruções de serviço

Por favor leia e conserve em seu poder

Gebruiksaanwijzing

Lees en let goed op deze advizen

Brugsanvisning

Vær venlight at læse og opbevare

Bruksanvisning

Vennligst les og ta godt vare på denne informasjonen

Bruksanvisning

Var god läs och tag tillvara dessa instruktioner

Käyttöohje

Lue ja säilytö

Introduction

Technical Data

Safety advice

Measured sound value

Measured vibration value

Usage

You demand the best and buy quality - quality provided by Atlas Copco. We have built for you a reliable and lasting tool. Working effectively and without endangering your health is only possible if this instruction for use is read carefully before first using the tool. We want to satisfy our customers and would like you to buy again

AEG Electric Power Tools from Atlas Copco.

Type

Nominal power (W)..................................................................

DSE 220 DSE 260

220

Min. orbital frequency at no load (min -1 )..................................

6500

Max. orbital frequency at no load (min -1 ).................................

11500

260

8000

11500

Orbit diameter (mm) ................................................................

1.5

Base plate, size from corner to corner (mm) ...........................

105

1.5

105

Weight (kg) ..............................................................................

Electronics ...............................................................................

1.1

1.1

■ Please pay attention to the safety instructions in the attached leaflet!

■ Do not pierce the motor housing as this could damage the double insulation

(use adhesives).

■ Always disconnect the plug from the socket before carrying out any work on the machine.

■ Only plug-in when machine is switched off.

■ Keep mains lead clear from working range of the machine. Always lead the cable away behind you.

■ Before use check machine, cable, and plug for any damages or material fatigue.

Repairs should only be carried out by authorised service agents.

■ Allow the machine to come to a stop before putting down.

■ Appliances used at many different locations including open air must be connected via a current surge preventing switch.

■ Always wear goggles when using the machine. It is recommended to wear gloves, sturdy non slipping shoes and apron.

■ Dust that arises when working in stones with crystalline silicic acid can damage your health. Please note the safety regulations, VBG, of the employer’s liability insurance association.

■ This machine are suitable only for dry sanding.

■ Dust that arises when working on wood or using the tool on industrial material can be dangerous to health. In this case connect the tool to a suction device.

Typically the A-weighted sound pressure level of the tool is 72 dB (A).

The noise of this power tool is measured according to IEC 59 CO 11, IEC 704,

DIN 45 635, part 21, NFS 31-031. The sound level may exceed 85 dB (A) at your working place; in this case sound insulation measures are necessary for the operator.

Typically the weighted acceleration is 2.7 m/s 2 .

The detail sander can be used for sanding a large variety of surfaces, especially in corners and on edges, as well as in confined areas.

Do not use this product in any other way as stated for normal use.

ENGLISH 6 DSE 220, DSE 260

Brief description

Infinitely variable electronic speed pre-selection for working a large variety of surfaces.

Speed adjustment knob

On/Off switch

Dust-bag connector

Tool reception

Sanding disk

Lamella base plate

Sandpaper

Lamella sandpaper

ENGLISH 6

Modifications: Text, diagrams and data are correct at the time of printing. In the interest of continuous improvement of our products, technical specifications are subject to alteration without prior notice.

DSE 220, DSE 260

Mains connection

Switching on and off

Connect only to a single-phase AC current supply and only to the mains voltage specified on the rating plate. Connection to sockets without earth protection is possible as the appliance features protective insulation to DIN 57 740/ VDE 0740 and CEE 20. Radio suppression complies with the European standard EN 55014.

When fitting the plug, make sure that the brown (live) wire of this appliance is connected to the plug terminal marked L or coloured red, and the blue (neutral) wire of this appliance is connected to the plug terminal marked N or coloured black.

Under no circumstances must the wires of this appliance be connected to the earth terminal of the plug marked either E, with the earth symbol, or coloured green or green/yellow.

Switching on: Move the slide switch to the left in direction of arrow. The switch engages.

Switching off: Depress "OFF" button of the slide switch. The switch moves automatically back to the 0-position.

Electronics

Speed selection

Due to the electronic the speed can be controlled by setting the wheel to suit the various materials.

The speed is adjusted by means of the electronic thumb wheel.

1 = lowest r.p.m.

6 = largest r.p.m.

1

Mounting the base plate/ lamella base plate

Always disconnect the plug from the socket before carrying out any work on the machine.

Mount the base plate (turned approx. 15°) to the tool reception (as shown in illustration) and turn it in direction of arrow until it locks.

ENGLISH 6 DSE 220, DSE 260

advertisement

Related manuals

advertisement